Eiki | LC-7000UE | manual | LC-7000UE Owners Manual

LC-7000UE Owners Manual
 MULTIMEDIA PROJECTOR
MODEL LC-7000U E
AN
3
y
AMONT
||
OWNER'S INSTRUCTION MANUAL
INFORMATION TO THE USER
NOTE: This equipment has been tested and found to comply with the limits for a Glass À digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment, This equipment generates, |
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely 1o cause harmful interference in which case the user will be
required to correct the interference at his own expense.
iS,
i SAFETY PRECAUTIONS )
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
The projector has a grounding-type AC line plug. This is a safety feature to be sure that the plug will fit
into the power outlet. Do not try to defeat this safety feature.
Intense light source. Do not stare directly into the projection lens as possible eye damage could result.
Be especially careful that children do not stare directly into the beam.
If the projector will not be used for an extended time, unplug the projector from the power outlet.
READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
THIS SYMBOL INDICATES THAT DANGER- THIS SYMBOL INDICATES THAT THERE ARE
0 OUS VOLTAGE CONSTITUTING A RISK OF IMPORTANT OPERATING AND MAINTENANCE
ELECTRIC SHOCK IS PRESENT WITHIN INSTRUCTIONS IN THE OWNER'S MANUAL
THIS UNIT, WITH THIS UNIT,
IMPORTANT:
For your protection in the event of theft or loss of this LG
Data-Grade projector, please record the Model Number
and Serial Number located on the rear of unit and retain Model No: LC-7000UE
this information. Refer to these numbers whenever you call
upon your authorized dealer regarding this product. Serial No:
Do not discard shipping carton and packing materials.
These items may be needed for storage or future
servicing.
us
Al the safety and operating instructions should be read
before the product is operated.
Read all of the instructions given here and retain them for
later use. Unplug this projector fram AC power supply
before cleaning. Do not use liquid or aerosol cleaners. Use
a damp cloth for cleaning.
Do not use attachments not recommended by the
manufacturer as they may cause hazards,
Do not placa this projector on an unstable cart, stand, or
table. The projector may fall, causing serious injury to a
child or adult, and serious damage to the projector. Usa
only with a cart or stand recommended by Ihe
manufacturer, or sold with the projector. Wall or shelf
mounting should follow the manufacturer's Instructions,
and should use a mounting kit approved by the
manufacturer.
Do not expose this unit to rain or use near water... for
example, in a wet basement, near a swimming pool, etc...
slots and openings in the back and bottom of the cabinet
are provided for ventilation, to insure reliable operation of
the equipment and to protect it from overheating.
The openings should never be covered with cloth or other
material, and the bottom opening should not ba blocked by
placing the projector on a bed, sofa. rug, or other similar
surface. This projector should never be placed near or
over a radiator or heat register.
This projector should not be placed in a built-in installation
such as a bookcase unless proper ventilation 1s provided.
This projector should be operated only from the type of
power source indicated on the marking label. If vou are not
sure of the type of power supplied, consult your authorized
dealer or local power company.
Do not overload wall outlets and extension cords as this
can result in fire or electric shock. De not allow anything to
rest on the power cord. Do not locate this projector where
tne cord may be damaged by persons walking on it.
Never push objects of any kind into this projector through
cabinet slots as they may touch dangerous voltage points
or Short out parts that could result in a fire or electric
shock, Never spill liquid of any kind on the projector.
Do not attempt to service this projector yourself as opening
Or removing covers may expose you 10 dangerous voltage
or other hazards, Refer all servicing to qualified service
personnal.
IMPORTANT SAFETY INSTRUCTIONS )
Unplug this projector from wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed,
b. If quid has been spilled into the projector.
c. If the projector has been exposed to rain or water.
d. If the projector does not operate normally by following
the operating instructions, Adjust only those controls
that are covered by the operating instructions as
improper adjustment of other controls may result im
damage and will often require extensive work by a
qualified technician to restore the projector to normal
operation,
e If the projector has been dropped or the cabinet has
heen damaged,
|. When the projector exhibits a distinct change In
performance-this indicates a need for service
when replacement parts are required, be sure the service
technician has Used replacement parts specified by the
manufacturer that have the same charactenstics as the
original part. Unauthorzed substitulions may result in fire,
electric shack, or injury to persons.
Upon completion of any service of repairs to this projector,
ask the service technician to perform routine safety checks
to determine that the projector ls in safe operating
condition.
This projector is equipped
with a grounding type AC
ing plug. Should you be
unable to insert the plug
into the outlet, contact your
glecirician. Do not defeat
GROUND the safety purpose of this
grounding type plug.
Follow all warnings and instructions marked on the
projectors.
For added protection to the projector during a lightning
storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet, This will
prevent damage due to lightning and powerline surges.
An appliance and cart combination
should be moved with care. Quick
stops, excessive force, and uneven
surfaces may cause the appliance
and car combination to overturn.
( TABLE OF CONTENTS
INTRODUCTION cov ovrrerrrr mmr rims as rams aa a sr mrs rr 11 1 4 aE a FE SECTE ES EEE EEE NEA ET EU TE N ENT TENUE TU EENE
POWER REQUIREMENT ------=---=:=--
EETTINÓ-UB THE PROJEN EOFE-:=========="===:e1c0:-r taa: Hi) des Cani edans ae rame RE RES
MOVING THE PROJECTOR:---------==c==ecrrcereeracinerererieraneroreretncear arrancar erre rParsa a earn
CONNECTING THE PROJECTOR: + ttre tsersrssresssnetarssssnesrsssryssinnsssssssossosssannsssrsosssnsssonesons
OPERATION OF CONTROLS EEE EEE ddaV raisin st nan
OPERATION OF REMOTE CONTROL -------=e=vrev=evccsrecccartcnartenceceren reine ene erccaa ree io meneame.
CONTROL ME PAOJECTOR “imc ima nie Eire arar arte rey torera a veta Liz
USING THE PROJECTOR --+=:-+++=+-e+sirccencarariiateoricererareacentecenrraneattnracatane canica acarrear ener ate
COMPUTER SYSTEM SELECT (COMPUTER MODE) -+--==-=e===eíieieenierecconeneenaos
PICTURE IMAGE ADJUSTMENT (COMPUTER MODE)-<…..<<.…..….seeccecccees
PICTURE SCREEN ADJUSTMENT (COMPUTER MODE) -+-=========e===vrr=ecereornreearrenennararreereneros
COLOR SYSTEM SELECT (VIDEO MODE) ---:--+:.cesererievinvercarenvnorevevóacaaranenearran ne ree cioo.
PICTURE IMAGE ADJUSTMENT (VIDEO MODE) --==-============v===ecrrcereerecioreracoss
PICTURE SCREEN ADJUSTMENT (VIDEO MODE) -------==v+-ercieseereeneenecrconenrnenennervencenacnnnn— es
OTHER FUNCTION SETTING +:::105:c6mu2imiiia HS
CARA A STE NE: . drco ero retar hi AA Las re ch MAR Ed 0 A ts Teas LALA rn hid An
AIR FILTER CARE AND CLEANING +45 stisiaiats sets ribs 1ats ih ibisdidiissaduns RER
TEMPER ÁTURE WARNING INDICATOR --—=-e-6ec0iciriidaenaciirim ia e ena perito ride idicacaondo as
TROUBLESHOOTING::-=-:-==+==::-=vrcenbererenivanibca rre ia ae ene Ae teatre
TECHNICAL SPECIFICATION:?S:==================-
-8-9
10-17
EE ra rrmae a aí 18-19
20-21
22-23
24-25
ERR нача 26-27
28-30
31
32
33
Ce Ca E ть 34
35
pre 2e E 36-39
-40
41
41
42
-43
-43-44
45
( INTRODUCTION | )
The projector is a multimedia projector designed for portability, durability, and ease of use. The projector utilizes built-in
multimedia features, a palette of 16.8 million colors, and active matrix liquid crystal display (LCD) technology,
COMPATIBILITY
The projector is compatible with many different types of personal computers and video devices, including;
® |BM-compatible computers, including laptops, up to 1024 + 768 resolution with à vertical frequency up to 75Hz.
* Apple Macintosh and PowerBook computers up to 1024 = 768 resolution.
e Various VCRs, video disc players, video cameras, satellite TV tuners or other AV equipment using any of the worldwide
video standards, including NTSC, NTSC4.43, PAL and SECAM.
IMAGE RESOLUTION
The resolution of the projector's projected image is B32 = 624, The projector displays computer images just as they
appear on your computers monitor. Screen resolutions between 832 » 624 and 1024 + 768 are compressed to 800 +
600, The projector cannot display screen resolutions above 1024 ~ 768, If your computer's screen resolution is higher
than 1024 > 768, reset it to a lower resolution before you connect the projector.
PORTABILITY
The projector Is extremely compact in size and weight, Having a sophisticated shape Ike an attaché case with a
retractable carrying handle, the projector will help you make powerful presentations wherever you go. To strengthen the
portability, the LENS RETRACT function is designed to protect the lens from being damaged during transportation. With
this function, the lens is retracted when the power is off,
UNPACKING THE PROJECTOR
The projector comes with the parts shown listed below. Check to make sure all are included. If any parts are missing,
contact an authorized dealer or service station,
a Owners Manual.
e Warranty Card.
® AC Power Cord.
& Remote Control Transmitter Unit and batteries.
a Lens Cover,
a Protective Dust Cover,
8 VGA Cable.
e VGA/MAC Adapter.
® Mouse Cable for PS/2 port.
e Mouse Cable for serial port.
® Mouse Cable for ADE port,
TRADEMARKS
e Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer, Inc.
a IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc,
POWER REQUIREMENTS
Your projector uses nominal input voltages of 100-120 VAC. The
projector automatically selects the correct input voltage. The
projector is designed to work with single-phase power systems
having a grounded neutral conductor. To reduce the risk of
electrical shock, do not plug into any other type of power system.
Consult your authorized dealer or service station if you are not
sure what type of power is supplied to your building.
/
a
L
Connect the AC power
supply cord (supplied) to
the projector,
Slide the guard when the AC cord may
not be connected by the guard.
GUARD
4
Projector side (Female) AC outlet side (Male)
ZZ
Hz
DESCRIPTION
| FRONT ;
INFRARED
REMOTE
RECEIVER
PROJECTION LENS
~~ REMOVABLE
LENS COVER
REAR |
EXHAUST VENT Bh
ra INFRARED
| A REMOTE
| MAIN ON/OFF RECEIVER
CAUTION HOT AIR | SWITCH
Air blown from the exhaust vent ls hot.
Observe the following when handling your
projector or choosing a location to install it.
* Keep heat-sensitive objects away from the
exhaust port.
e If you set the projector on top of a metallic
surface, the surface will become hot because
of the hot air exhaust. Be careful when
handling.
a Do not touch the cabinet near to the exhaust
vant, and especially screws and metallic parts.
These parts will become hot while the projector
Is used,
CARRY HANDLE
POWER CORD
CONNECTOR
[—— LAMP COVER
LEVELING/ELEVATING
FEET
AIR INTAKE
VENT
( SETTING-UP THE PROJECTOR )
- ® This projector is basically designed to project on a fiat projection surface.
POSITIONING: ® This projector can be focused from 3.6' (1.1m) ~ 75.6" (23.0m).
® Use the illustration below as an example when positioning the projector to the screen.
Maximum Zoom
ROOM LIGHT
ideally the projector should be placed in a Minimum Zoom 7
room with limited light. Picture quality will be
directly affected by lighting conditions,
HI
Hz
DISTANCE
| Screen| Max Zoom| 32 60" | 100 150° 200" 300° 1: 400° tag
Size (Min. Zoom | 20" SLL Lae 94" 125" 188" | 250 400"
Distance ECE т) | 6.9'{2.1 т) |1 1.8'(3.6 m)[17.8'(5.4 m)| 23.7'(7.2 m)|35.2'(10.7 т)| 47'(14.3 m)| 75.6'(23.0 m)
Screen Size 20 60" 100” 150" 200" 300 | 400" |
(W = H) inch 16x12 | 48x 36 80 = 60 120 = 90 | 160 120 240 + 180 Ш 320 = 240 |
Height (H1) 10.7 inch 32 inch 53inch | B0inch 106 inch 160 inch__ | 212 Inch
Height (H2) 1.3inch 4 inch 7 inch 10 inch 14 inch 20 inch 28 inch
VENTILATION
Although this projector has a cooling fan to protect from overheating,
please be careful to set the projector so that it can cool properly and
you can avoid a risk of fire and malfunction,
e Do not cover the vents with papers or other materials.
A e Keep the side grill at least 3.3" (1m) away from any
object.
# Make sure that there are no objects under the projector,
An object under the projector may prevent the projector
from taking the cooling air through the bottom vent,
EXHAUST VENT
AIR INTAKE VENT
(BOTTOM SIDE)
LEVELING AND ELEVATING ADJUSTMENTS
Screen positioning adjustment can be made with the two
leveling/elevating feet.
Adjustments of up to 6” are possible by rotating the feet on the
bottom of the projector.
Level the projector, by rotating the two feet (left and right) on the
bottom of the projector.
LEVELING/ELEVATION
FEE]
a MOVING THE PROJECTOR )
Use the carry handle when moving the projector.
Replace the lens cover when moving the projector to
prevent damage to the lens.
( ~ CONNECTING THE PROJECTOR _ )
Your projector is equipped with various audio/video inputs and outputs including Computer HDB15-pin (VGA) terminals,
Monitor HDB15-pin (VGA) terminals and 5-VHS video.
CONNECTING THE COMPUTER
CONNECTING TO THE COMPUTER INPUT HDB15-PIN (VGA) TERMINALS (1 and 2)
Personal computers can be connected to the HDB15-pin (VGA) terminal on the projector. |
e Connect the computer to these terminals using the VGA cable or VGA cable with VGA/MAG adapter (provided).
WARNING: For projectors, the VGA cable provided is designed to reduce RFI (Radio Frequency Interference)
emissions. For regulatory compliance reasons, this cable must be used and must not be replaced by any
other cable.
CONNECTING TO THE MONITOR OUTPUT HDB15-PIN (VGA) TERMINAL
This terminal contain the information that is viewed on the screen.
Monitor can be connected to the HDB15-pin (VGA) terminal on the projector.
# Connect the monitor to this terminal using the monitor cable (not provided).
Pin No./Signal Pin No./Signal
1 Red input 8 Non Connect
2 Green input 10 Ground (Vert. sync.)
3 Blue input 11 Sense 0
4 Sense 2 12 Sense 1
5 Ground (Horiz. sync.) 13 Horz. sync.
6 Ground (Red) 14 Vert sync.
7 Ground (Green) 15 Reserved
8 Ground (Blue)
CONNECTING TO THE COMPUTER AUDIO INPUT JACKS (1 and 2)
® Connect audio outputs from your computer to these jacks using the audio cable (not provided).
CONNECTING TO THE MULTI-POLE 12-PIN (CONTROL PORT) CONNECTOR
e When the computer (connected to the COMPUTER INPUT 1 terminal only) is operated by the remote control unit,
connect three different type of cables (provided) between control port and computer mouse port or serial port.
NOTE: The computer connected to the COMPUTER INPUT 2 terminal cannot be operated by the remote control unit.
| CAB LE
Mouse Cable for P3/2 port. =
Mouse Cable for Serial port.
COMPUTER TYPE =
IBM Compatible computer with PS/2 mouse port.
¡BM Compatible computer with senal contro) port,
Apple Macintosh computer with ADB mouse port. i Mouse Cable for ADB port.
P52 | Serial ADB
HE CONTROL PORT Port Port port. | — =
= Je — CONTROL PORT CABLE
<a REMOVAL HINT
A == — — To disconnect the control port cable
5 —_— | —— — connector procead as follows.
6 | — — — |
me — 1. Hold the portion (A) of the
1 TE connector.
— 2. Pull the portion (B) to
= GND GND ue disconnect,
a — | — | —— =
— EE |
— 10 —
Connecting an IBM-compatible desktop computer
COMPUTER
"TES
COMPUTER
OUTPUT VGA CABLE MONITOR CABLE
{ (PROVIDED) (NOT PROVIDED)
UL Je
AUDIO SERIAL PORT PS
QUTPUT INPUT PORT INPUT
COMPUTER (= МЕД MONITOR
INPUT 1 or 2 im OUTPUT
MOUSE CABLE
FOR PS/2 PORT /(-
РВОМ!
(PROVIDED) ff к
rfi
CONTROL PORT
OUTPUT
MOUSE CABLE I
FOR SERIAL PORT
(PROVIDED) ® ae
== =a] [ee Ep нове L pd
AUDIO CABLE OMPUTER == J
(NOT PROVIDED) AUDIO INPUT =
10r2 ha rh
CAUTION
1. The hook up should be done as per the above illustration. After hook
up, turn on the projector, monitor, computer, in that order.
2. The CONTROL PORT can only be used with the computer connected
to the COMPUTER INPUT 1 terminal.
Connecting a Macintosh desktop computer
COMPUTER
Te
MONITOR CABLE
(NOT PROVIDED)
COMPUTER
OUTPUT
VGA GABLE
d (PROVIDED)
DI ———
E
VGA/MAL ADAPTER
AUDIO ADB
OUTPUT PORT INPUT (PAOWIDEU)
COMPUTER E = MONITOR
INPUT 1 or 2 OUTPUT
MOUSE CABLE
FOR ADB PORT
(PROVIDED)
CONTROL PORT
OUTPUT
AUDIO CABLE COMPUTER = -
(NOT PROVIDED) AUDIO INPUT = =
1or2 \
Set the slide switches as shown in the table below VGAMAC ADAPTER
depending on the RESOLUTION MODE that you want
to use before you turn on the projector and computer.
м _— SW4-SW6
| RESOLUTION MODE |SWi| SW2|swa| swa|Sw5|sw6| ом
| 18" MODE (640 < 480) | ON | OFF | OFF | OFF | OFF | OFF |
| 16 MODE (832 624) | OFF | OFF | OFF | OFF OFF | ON | a
CAUTION
1. The hook up should be done as per the above illustration. After hook
up, turn on the projector, monitor, computer, in that order.
2. The CONTROL PORT can only be used with the computer connected
to the COMPUTER INPUT 1 terminal.
OFF
{5
Connecting an IBM-compatible laptop computer
COMPUTER
COMPUTER
OUTPUT VGA CABLE
(PROVIDED)
jon |
AUDIO SERIAL PORT PS/2
OUTPUT INPUT PORT INPUT
Ш
COMPUTER (VËV
INPUT 1 or 2 [OL
MOUSE CABLE
FOR PS/2 PORT 7 —
(PROVIDED) |
CONTROLPORT. | ||
OUTPUT
MOUSE CABLE mf
FOR SERIAL PORT
(PROVIDED)
a ==
AUDIO CABLE COMPUTER
(NOT PROVIDED) AUDIO INPUT
1or2
1. The hook up should be done as per the above illustration. After hook
up, turn on the projector, computer, in that order.
2. The CONTROL PORT can only be used with the computer connected
to the COMPUTER INPUT 1 terminal.
— 14 —
= EE TEE
Connecting a Macintosh PowerBook computer
COMPUTER
The Macintosh PowerBook requires the use of the
PowerBook Video Adapter shipped with the PowerBook.
TO POWERBOOK
VIDEO ADAFTER
= VGA CABLE
Я нет Г (PROVIDED)
ESA dE
1 ——
AUDIO ADB VGA/MAC ADAPTER
OUTPUT PORT INPUT (PROVIDED)
COMPUTER
INPUT 1 or 2
MOUSE CABLE
FOR ADB PORT
(PROVIDED) |
CONTROL PORT Te
OUTPUT
ALI del y
© ©) ©
®
EXT SPW Ski
AUDIO CABLE COMPUTER =
(NOT PROVIDED) AUDIO INPUT
lor2
Set the slide switches as shown in the table below VGA/MMAC ADAPTER
depending on the RESOLUTION MODE that you want ST
to use before you turn on the projector and computer,
3W1- SW6
| 13" MODE (640 x 480) | ON | OFF | OFF | OFF | OFF| OFF | 0
| 16" MODE (832 x 624) | oF | oFF | oFF | ОРЕ | oFF | ON |
[ RESOLUTION MODE |swi|sW2|swa]swa|sws]Sws]
a
OFF
CAUTION
1. The hook up should be done as per the above illustration. After hook
up, turn on the projector, computer, in that order.
2. The CONTROL PORT can only be used with the computer connected
to the COMPUTER INPUT 1 terminal.
Ч
CONNECTING THE VIDEO EQUIPMENT
CONNECTING TO THE AV INPUT JACKS
Connect to the video and audio outputs of a VCR, video disc player, video camera, satellite TV tuner or other AV
equipment.
® Connect audio/video outputs from external sources to these input jacks using the audio/video cable.
e If the audio signal from the AV equipment is stereo, be sure to connect the right and left channels to the respective right
and left audio input jacks.
e |f the external audio signal is monaural, connect it to the left jack.
S-VHS FORMAT VCR CONNECTION
The AV input includes an extra video input jack marked S-VIDEO to allow connection to an S-VHS format VCR that has
separate Y/C video signals. The S-VIDEO jack has priority over the VIDEO jack.
CONNECTING TO THE MONITOR OUTPUT JACKS
These jacks contain the audio/video information of the viewed image.
® Connect audio/video inputs from AV equipment to these output jacks using the audio/video cable.
e | the Ep of the audio equipment is stereo, be sure to connect the right and left channels to the respective right
and left jacks.
e |f the audio input of the audio equipment is monaural, connect it to the left jack.
® YWhenever the S-VIDEQ signal source is viewed on the screen, the video signal available at the MONITOR OUTPUT
jack will be in black and white (monochrome).
Connecting the Video Equipment
4 VIDEO EQUIPMENT
| Video Cassette Recorder Video Disc Player Satellite
| TV Tuner |
| |
| |
A Na PT A AAA AE A CT a J
Lo E
VIDEO
AUDIO
OUTPUT CUTPUT
S-VIDEO
> INPUT
VIDEO INPUT Ц [mo
ra }5— | AU NE
Lape |: © — “
AUDIO INPUT Y AO PEF
alii
rn = \ AUDIO
nf eT = — INPUT
AUDIO MONITOR Wet | VIDEO
OUTPUT MONITOR
OUTPUT
A L Speaker (L)
AUDIO SPEAKER
VIDEO
INPUT QUT | INPUT AUDIO S-VIDEO
OUTPUT OUTPUT
= тен
S-VHS VCR
Speaker (R) MONITOR
NOTE: The hook up should be done as per the above illustration. After hook up, turn on the projector, video equipment,
in that order.
—16—
CONNECTING AN EXTERNAL SPEAKER
CONNECTING TO THE EXT. SP. JACK (3.5mm mini stereo type)
This jack contains the audio information of the viewed image. Use it to connect an external speaker system when using
this jack. It will turn off the audio from the internal speaker.
тон — я
я ]
Foal ITER
ALICE 14
вен |
ALDI I 2
AUDIO LO ®)
q ее O Ch
aces e
£
=
7
EXTERNAL
SPEAKERS SYSTEM )
ep DO
C
©
OPERATION OF CONTROLS 8 y
TOP OF THE PROJECTOR =
ТОР
CONTROL
LAMP POWER INDICATOR
Light is dim when the projector is on.
Light is brightened when the projector is in stand-by mode.
READY INDICATOR
Light is green when projector lamp is ready to be turned on,
TEMPERATURE WARNING INDICATOR
Flashes red when internal projector temperature |8
too high.
LAMP REPLACEMENT INDICATOR
Light is orange when projection lamp
is nearing end of service life.
LAMP POWER ON/OFF BUTTON
Used to urn projection lamp on or off.
MODE BUTTON
Used to select video source
(Computer 1, Computer 2 or VIDED
Input)
NORMAL BUTTON
Used to reset to normal picture
adjustment preset by factory,
VOLUME BUTTONS
Used to adjust volume,
® seccreurron
SYSTEM BUTTON This button has different functions depending on
Use this button, the POINT UP/DOWN buttons tem selected, 10 Increase or decrease the values
and the SELECT button to select computer in_cerain Пете such as COLOR or
8 VIDEO Mode [12 ur pown BUTT
Use this button, the POINT UP/DOWN buttons @ To select an it Lat, un
d the SELECT b | elect an item on the that you want to adjust
button either A or Y.
od ое, @ Used to operate power zoom lens or power focus
15 button will activate the MENU operation, system. (Pressing these button either 4 or Y.)
Use this button, the POINT UP/DOWN buttons and
the SELECT button to mak
projector's setting in MENU us 7 ¿es © ZOOM/FOCUS BUTTON
| Used to select power zoom lens or focus adjust.
— TH —
9 9 9006
SIDE OF THE PROJECTOR
(de
i hry у
es
CONTROL FORT
@—
(EE
VIDED Sven
o
ALE MA
@
922216
Fauna BY ae
COMPUTER INPUT TERMINALS (1 and 2)
Used to connect a computer to the projector.
MONITOR OUTPUT TERMINAL
Used to connect a monitor to the projector.
CONTROL PORT CONNECTOR
(For the Computer Input-1 terminal only)
Used to connect a mouse cable to the projector.
COMPUTER AUDIO INPUT JACKS (1 and 2)
mini stereo type
Used to connect a computer audio input to the
projector.
AUDIO INPUT JACKS
Used to connect an audio input to the projector.
ee
Фе
© VIDEO INPUT JACK
Used to connect a video source to the projector.
20 S-VIDEO INPUT JACK
Used to connect a 5-VHS video source to the projector.
AUDIO MONITOR OUTPUT JACKS
Permits audio connection to a monitor.
VIDEO MONITOR OUTPUT JACK
Permits video connection to a monitor.
E) EXT. 5P. JACK (3.5 mm mini stereo type)
Used to connect a external speakers system.
C
This remote control unit can be used not only as a remote control
for the projector operation but also as a wireless mouse for PC,
The remote control unit has a pointing pad and two click buttons.
The wireless mouse function ls activated when you do not adjust
the setting by using the MENU operation,
NOTE: To use the wireless mouse function, connect the aftached
cable between the projector and your PC since the mouse
control signal 1s transferred through the projector. Use the
proper cable and follow the instruction as described in
section "CONNECTING THE PROJECTOR" on pages 10 -
14 depending on your PC.
| FRONT |
POINTING PAD
(POINT UP/DOWN BUTTON)
(Oo, — When In use as a remote for the
| projector.
To select an ¡tem on the MENU that you
want to adjust, To select an item, move
SO the arrow by pressing the pad ether
upward or downward.
Used to operate power zoom lens or
power focus system by pressing the pad
either upward or downward
When in use as a wireless mouse
Used to move the pointer, The pointer is
moved according to the direction you
are pressing.
FRONT CLICK BUTTON
This button has (he same function as
the right button in a PL mouse
Pressing this button does not affect any
operation when in MENU moda.
ZOOM/FOCUS BUTTON
Used to select power zoom lens or focus
adjust.
O VOLUME BUTTONS
Used to adjust volume,
SOUND MUTE BUTTON
Used to mule sound.
MENU BUTTON
This button will activate the MENU operation.
Use this button, the FOINT UP/DOWN button
and the SELECT (REAR CLICK) button to make
adjustments to the projectors setting in MENU
operation.
OPERATION OF REMOTE CONTROL )
SELECT (REAR CLICK) BUTTON
When in use as a remote for the
projector.
This bution has different functions
depending on when used. This bution is
used to execute the item selected, lo
increase or decrease the values In
certain items such as COLOR or
BRIGHTNESS,
When In use as a wireless mouse
This button has the same function as
thé left button In à PC mouse.
FINE SYNC BUTTONS
Used t0 adjust fine sync.
LAMP POWER ON/OFF BUTTON
Used to turn the projection lamp on or off
MODE BUTTON
Used to select video source, (Computer 1,
Computer 2 or VIDED Input)
NORMAL BUTTON
Use to reset to normal picture adjustment presat
by factory,
FREEZE BUTTON
Use this button to freeze on-screen image
REMOTE CONTROL BATTERY INSTALLATION
Remove the battery Slide the batteries into the Replace the compart-
compartment lid, compartment, ment lid,
Mote: For correct polarity (+ and -
terminal), be sure the battery
terminals are In contact with
tha pins in the compartment
USING THE REMOTE CONTROL UNIT
Point the remote control toward the projector (Receiver window) whenever pressing the buttons. Maximum operating
range for the remote control is about 16.4 (5m) and 60" front and back of the projector.
| To insure safe operation, please observe the following precautions:
Use (2) AA type manganese or alkaline batteries.
Change two batteries at the same time,
Do not use a new battery with a used battery.
Avoid contact with water
Do not drop the remote control unit.
If batteries have leaked on the remote control, carefully wipe the case
clean and load new batteries,
( CONTROL THE PROJECTOR
The projector has two types of operation: DIRECT OPERATION and MENU OPERATION. DIRECT OPERATION
allows you to operate the projector by using one button without showing the MENU. In MENU OPERATION mode,
you display menus where you can adjust the projector's settings. Follow the instruction for each control,
DIRECT OPERATION
TOP CONTROL
ADJUST ITEM OF THE PROJECTOR REMOTE CONTROL UNIT
LAMP POWER ON/OFF | LAMP POWER ON-OFF BUTTON LAMP POWER ON-OFF BUTTON
MODE SELECT MODE BUTTON MODE BUTTON
VOLUME ADJUSTMENT | VOLUME (+) and ( - ) BUTTONS VOLUME (+) and { — ) BUTTONS
SOUND MUTE NOT AVAILABLE MUTE BUTTON
ZOOM ADJUSTMENT ZOOM/FOCUS BUTTON ZOOM/FOCUS BUTTON
POINT UP/DOWN (4 /Y) BUTTONS| POINT (UP/DOWN) BUTTON
FOCUS ADJUSTMENT | ZOOM/FOCUS BUTTON ZOOM/FOCUS BUTTON
POINT UP/DOWN (A /¥ ) BUTTONS| POINT (UP/DOWN) BUTTON
NORMAL PICTURE NORMAL BUTTON NORMAL BUTTON
FREEZE PICTURE NOT AVAILABLE FREEZE BUTTON
FINE SYNC. NOT AVAILABLE | FINE SYNC. (+) and ( — ) BUTTONS
MENU OPERATION
1. COMPUTER MODE
| TOPCONTROL — |
COMPUTER SYSTEM MENU or SYSTEM BUTTON MENU BUTTON
POINT UP/DOWN ( A /Y ) BUTTONS | POINT (UP/DOWN) BUTTON
SELECT BUTTON | SELECT (REAR CLICK) BUTTON
CUSTOM MODE MENU BUTTON MENU BUTTON
POINT UP/DOWN (A / W ) BUTTONS| POINT (UP/DOWN) BUTTON
SELECT BUTTON SELECT (REAR CLICK) BUTTON
PICTURE IMAGE MENU BUTTON MENU BUTTON
one POINT UP/DOWN (A /W ) BUTTONS| POINT (UP/DOWN) BUTTON
H-POSITION SELECT EUTTON SELECT (REAR CLICK) BUTTON
V-POSITION
| PICTURE SCREEN MENU BUTTON MENU BUTTON
POINT UP/DOWN (4/Y ) BUTTONS| POINT (UP/DOWN) BUTTON
22
2. VIDEO MODE
POINT UP/DOWN (A /W) BUTTONS
SELECT BUTTON
ADJUST ITEM OF SM PROJECTOR REMOTE CONTROL UNIT
“COLOR SYSTEM MENU or SYSTEM BUTTON MENU BUTTON
POINT UP/DOWN (A/Y)BUTTONS| POINT (UP/DOWN) BUTTON
SELECT BUTTON SELECT (REAR CLICK) BUTTON
PICTURE IMAGE MENU BUTTON MENU BUTTON
TINT POINT UP/DOWN (A /W)BUTTONS| POINT (UP/DOWN) BUTTON
CONTRAST SELECT BUTTON SELECT (REAR CLICK) BUTTON
BRIGHTNESS
SHARPNESS =
PICTURE SCREEN MENU EUTTON MENU BUTTON
POINT (UP/DOWN) BUTTON
SELECT (REAR CLICK) BUTTON
3. COMPUTER/VIDEO MODE
ADJUST ITEM SPTOE PROJECTBA REMOTE CONTROL UNIT
| OTHER FUNCTION | | MENU BUTTON | MENU BUTTON
TE | POINT UP/DOWN (4/Y)BUTTONS| POINT (UP/DOWN) BUTTON
| | | SELECT (REAR CLICK) BUTTON
REVERSE L/R SELECT BUTTON ( KK
BLUE BACK
DISPLAY |
MODE FREE |
| LANGUAGE
NOTES:
1. The MENU, once activated, will not disappear unless you have choose QUIT operation. If you switch to
DIRECT operation by pressing a DIRECT operation button while in MENU mode, the menus will disappear
and the MENU operation will end.
2. You can use the REMOTE CONTROL UNIT or the TOP CONTROL OF THE PROJECTOR to operate the
MENU operation.
3. You cannot make adjustments to items that are in gray letters. Only items that are in black letters are
available.
o 1
( USING THE PROJECTOR ==
TO TURN ON THE PROJECTOR
Connect the projector to a video source (Computer, VCR, Video Camera, Video Disc Player, elc.) using the appropriate
terminals on the side of the projector (Sea "CONNECTING THE PROJECTOR" section on pages 10-17).
Connect the projector's AC power cord into a wall outlet and turn the MAINS ON/OFF switch (located on the back of the
projector) to the ON position. The LAMP POWER indicator will light RED, the READY indicator will light GREEN.
Prass the LAMP POWER ON/OFF button on the remote control unit or on the
projector to ON. The LAMP POWER indicator light will dim and the cooling fans will
operate. The count-down display appears on the screen and the count-down starts
(20-19-18-...1). The signal from the video source appears after 30 seconds.
CAUTION: ,
A THIS PROJECTOR USES A METAL-HALIDE ARC LAMP. TO EXTEND THE LIFE OF THE LAMP, ONCE
YOU HAVE TURNED IT ON, WAIT AT LEAST 5 MINUTES BEFORE TURNING IT OFF.
NOTE: TEMPERATURE WARNING INDICATOR flashes red, the projector will be automatically turned of.
Wait at least 5 minutes before turning the projector on.
If the TEMPERATURE WARNING INDICATOR continues to flash, follow the procedures below:
(1). Press LAMP POWER ON/OFF button to OFF.
(2). Check the air filter for dust accumulation,
(3). Remove dust with vacuum cleaner (See "AIR FILTER CARE AND CLEANING" section on page 41.)
(4). Prass LAMP POWER ON/OFF button to ON,
if the TEMPERATURE WARNING INDICATOR still continues to flash, call your authorized dealer or service
station.
TO TURN OFF THE PROJECTOR
Press the LAMP POWER ON/OFF button on the remote control unit or on the
projector. The "POWER OFF 7?" appears on the screen. Press again the LAMP
POWER ON/OFF button to turn OFF the projector, The LAMP POWER indicator will
light bright and READY indicator will turn off. The cooling fans will operate for 1 minute —— |
after the projector is turned off. (During this "cooling down” period, the projector cannot | POWER OFF ? |
be tumed on.) The READY indicator will light green again and the projector may be
tumed on by pressing the LAMP POWER ON/OFF button,
== ЗА
MODE SELECT | rar
— COMPUTER 1| | — |COMPUTER 2
Press the MODE button (located on remote control unit or on the projector) ——
В уе SR 1 EAN 2 or VIDED Input. The "COMPUTER 1", a FA
! ‘or "VI " display will appear al the bottom right of the |
screen for a few seconds. E A od VIDEO | |
VOLUME ADJUSTMENT =
Press the VOLUME buttons (located on remote control unit or on the projector) to adjust
the volume. The volume display will appear at the bottom right of the screen for a few
seconds.
Pressing volume (+) to increase volume and increase the number on the screen.
Pressing volume (-) ta decrease volume and decrease the number on the screen == Sa a
SOUND MUTE FUNCTION
| VOLUME
Pressing the MUTE bution on the remota control unit to mute audio, Press the MUTE
button again to restore audio to its previous level. The mute display will appear at the 0-63 32
bottom right of the screen for a few seconds. MUTE
ZOOM ADJUSTMENT (With remote control unit) = =
Press the ZOOM/FOGUS button until zoom display appears on the screen, and press
POINT (UP/DOWN) button to obtain your desired picture size. The zoom display will
appear at the bottom right of ihe screen for a few seconds.
For a larger picture, press (UP) and for a smaller picture, press (DOWN).
ZOOM ADJUSTMENT Without remote control unit) |
ZOOM |
Press the ZOOM/FOCUS button until zoom display appears on the screen, and press г
FOINT UP/DOWN ( A / WF ) buttons. to obtain your desired picture size. The zoom display
will appear al the bottom right of the screen for a few seconds
Fora larger picture, press ( A) and for a smaller picture, press ( Y ).
FOCUS ADJUSTMENT (With remote control unit)
Press tne ZOOM/FOCUS button until thé focus display appears on the screen, and press
POINT (UP/DOWN) button to obtain a sharper, crisper picture. The focus display will
appear at the bottom right of the screen for a few seconds.
FOCUS ADJUSTMENT (Without remote control unit) FOCUS |
Press the ZOOM/FOCUS button on the projector until the focus display appears on the
screen, and press POINT UP/DOWN ([ & /'W ) buttons tó obtain a sharper, crisper picture.
The focus display will appear at the bottom right of the screen for a few seconds.
NORMAL PICTURE FUNCTION
The normal picture level is factory preset on the projector and can be restored anytime by "DEFAULT |
pressing the NORMAL button (located on remote control unit or on the projector), The
"DEFAULT" display will appear at the bottom right of the screen for a few seconds.
FREEZE PICTURE FUNCTION
Press the FREEZE button on the remote control unit, and the still picture will remain on-screen. This function is cancelled
when the FREEZE button is pressed again or any other function button is pressed.
NOTE: Your computer or video equipment is not affected by this function, and will continue to run
FINE SYNC ADJUSTMENT
Press the FINE SYNC (+) or (—) buttons on the remote control unit to eliminate flicker from
the display on computer mode. The fine sync display will appear at the bottom right of the | al
screen for a few seconds, FINE SYNC
NOTE: The projector may not reproduce a proper image for soma XGA signals. Since XGA
(1024 x 768) image is converted to SVGA (800 = 600) image by partial scan, some 0-127
lines and dots of the image do mot appear. The flicker on this compressad XGA image
cannot be eliminated even though you try to make a FINE SYNC adjustment,
— PE
=
COMPUTER SYSTEM SELECT (COMPUTER MODE) )
This projector is designed to adjust to different types of computer display signals based on VGA, SVGA or XGA (See
"COMPATIBLE PERSONAL COMPUTER SPECIFICATIONS" on the next page), If you set MODE SELECT to
"COMPUTER", the projector will automatically process the incoming signal and project the proper image without any
special setting. Although this will work in most cases, you may be required to manually set the projector for some
computer signals. If the computer image is not reproduced properly, try the following procedure and switch 1o the
computer display mode that you want 10 use. You can alter the system by using either the REMOTE CONTROL UNIT
ar the TOP CONTROL of the projector.
. Connect the COMPUTER and the PROJECTOR.
. Press the MODE BUTTON to set COMPUTER MODE.
Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear,
. Move the arrow by pressing the POINT (UP/DOWN) BUTTON(s) lo select SYSTEM. Press the SELECT (REAR
CLICK) BUTTON, Another dialog box, COMPUTER SYSTEM DISPLAY will appear. This shows the current display
mode initially detected by the projector.
5. If you want to change the display mode from the current one, point the arrow to SEARCH and then press the
SELECT (REAR CLICK) BUTTON and select one of the possible alternatives shown in the top row.
E. To quit the MENU, point to QUIT and then press the SELECT (REAR CLICK) BUTTON.
£a LO BI —
NOTE: 1, If the projector cannot discriminate or detect the input signal from the computer, the "GO TO CUSTOM
MODE" display appears.
NOTE: 2. If no input signal from the computer, the "NO SIGNAL" display appears on the screen,
MAIN MENU DISPLAY
172 COMPUTER SYSTEM
| SYSTEM + bp DISPLAY
IMAGE | + ===
— > | МСАТ — Hi
SCREEN —
= | SEARCH —+—
| SETTING = =
EZ | QUIT
LANGUAGE D ‘
QUIT ] | | CUSTOM MODE | A
For your reference, "CURRENT MODE" is also available. CURRENT MODE
This will appear by the parameter dialog box, and show SE ge
some characteristics of the display signal currently | H-SYNC FREQ. 36.5 |
connected. These figures are measured by the projector, | ay. | | |
CURRENT MODE includes "H-SYNC FREQ.", "V-SYNC | VETA 50.0
FREQ.", and "POLARITY" POLARITY H+V+
SIMPLE METHOD
1. Connect the COMPUTER and the PROJECTOR.
2. Press he MODE BUTTON to set COMPUTER MODE,
3. Press the SYSTEM BUTTON on the projector and the COMPUTER SYSTEM DISPLAY dialog box will appear,
4. If you want to change the display mode from the current one, point the arrow to SEARCH and then press the
SELECT (REAR CLICK) BUTTON and select ona of the possible alternatives shown in the top row.
5. To quit the MENU. point to QUIT and then press the SELECT (REAR CLICK) BUTTON.
CUSTOM MODE
This is a special function that may be used when a computer image is not reproduced properly. (See the pages 28 -
30 for more detail.)
COMPATIBLE PERSONAL COMPUTER SPECIFICATIONS
DISPLAY | RESOLUTION A (kHz) E (Hz)
VGA! 640 x 480 “e 59.88
VGAZ 720 x 400 31.47 70.09
VGA3 840 x 400 31.47 70.09
vos — 640 480 37.86 74.38
VGAS 640 > 480 37.86 7281 —
VGAS 640 > 480 31.70 61.91
MAC LC13 640 > 480 34.97 66.60
| MAC 13 640 x 480 — 35.00 66.67 |
PC98 640 400 — 2485 56.42
| FM TOWNS 640 * 400 24.38 55.40
| SVGAI 800 > 600 35.21 56.33
SVGA2 “800 * 600 — 9788 60.32
SVGAJ l 800x600 46.92 7508 —
SVGA4 800 > 600 48.32 76.33
SVGAS 800 * 600 48.01 71.98
SVGAG 800 = 600 37.90 61.03
— SVGA7 800 x 600 34.50 55.38
SVGAB B00 > 600 38.00 60.51
| SVGA9 800 > 600 | 3860 — eos
— SVGAIO 800 » 600 — 790 71.92
SVGA11 800 > 600 32.70 51.00
NC1 “800 » 600 38.00 6051
MAC 16 832 » 624 49.72 74.55
XGA 1024 x 768 48.36 60
— XGA?: 1024 x 768 — 5628 70.26
XGA3 1024x768 | 60.08 75.10
| XGA “1024 x 768 56.47 70.06
XGAS 1024 > 768 60.30 7491
XGAB 1024 » 768 48.50 60.02
XGAT 1024 х 768 | 44.00 54,59
XGAS | 1024 х 768 48.36 82.65
[INR 1024 х 768 36.00 87.17
Specifications are subject to change without notice.
J
CUSTOM MODE )
This projector can automatically detect most display signals in most personal computers currently distributed.
However, some computers employ a special signal format which is different from the standard ones and may not be
detected by this projector. If this happens, the projector cannot reproduce a proper image, often recognized as a
flickering picture, a non-synchronized picture, a non-centered picture or à skewed picture.
To project a proper image for those non-standard formats, this projector provides CUSTOM MODE, in which you can
precisely adjust several parameters lo match the input signal format. The projector has eight Independent memory
areas that you can store the parameter settings you have made. Therefore, you can recall the setting for a specific
computer when you need It
This adjustment is available by using either the REMOTE CONTROL UNIT or the TOP CONTROL of the projector.
1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog bax MAIN MENU DISPLAY
will appear,
2 Move the arrow by pressing the POINT UP/DOWN BUTTON(s) to | -
select the SYSTEM. Press the SELECT (REAR CLICK) BUTTON. SYSTEM + E
Another dialog box, COMPUTER SYSTEM DISPLAY will appear. > x;
1. Then, move the arrow by pressing the POINT UP/DOWN BUTTON(s) | IMAGE | E
to select the CUSTOM MODE. Press the SELECT (REAR CLICK) —
BUTTON, Another dialog box "WHERE TQ RESERVE", will appear SCREEN =
4. In this dialog box, you will select one of the memory areas shown as | =
"MODE!" to "MODES". If the parameters have been previously set and | SETTING >
stored to the memory, the status "STORED" will appear on a
corresponding row. If not, "FREE" will appear. LANGUAGE >
5. Move the arrow to one of the "MODES" that you want to by pressing -
the POINT UP/DOWN BUTTON(s). Press the SELECT (REAR CLICK) QUIT
BUTTON to select it.
NOTE: If all MODE= is STORED will appear, cannot stored the new PC
parameter data. In this case, you must be cleared the PC
parameter data used the MODE FREE Function.
(See "MODE FREE" section on page 38.)
COMPUTER SYSTEM DISPLAY
| GO TO CUSTOM MODE WHERE TO RESERVE
SEARCH MODE1 | STORED | +
Quit | MODE 2 | FREE - >
— — | MODE3 | FREE >
| CUSTOM MODE <— > —
— = MODE 4 | FREE >
“CURRENT MODE MODES | FREE > |
Fa | =: |
H-SYNC FREQ. 36.5 MODE 6 | FREE a
V-SYNC FREQ. 60.0 MODE 7 | FREE | >
POLARITY | H+V+ DOE Y [FREE | FREE >
For your reference, "CURRENT MODE" is also available. “QUIT
This will appear by the parameter dialog box, and show
some characteristics of the display signal currently
connected. These figures are measured by the projecior.
CURRENT MODE includes "H-SYNC FREQ", "V-8YNCG
FREQ." and "POLARITY"
6.
10,
11,
Another dialog box "CUSTOM MODE ADJUSTMENT DISPLAY 1° will
appear and the parameter data for the MODE you have selected Is shown
in this dialog box.
The parameters will be filled with the data determined by the projector
according to the present signal input.
The function of he parameters and their values are summanzed in the
right table.
, Move the arrow to an item that you want to adjust by pressing the POINT
UP/DOWN BUTTON(s).
To Increase the level, point the arrow to 5. and then press the SELECT
(REAR CLICK) BUTTON. To decrease the level, point the arrow to + and
then press the SELECT (REAR CLICK) BUTTON.
If you want to store the settings to the memory, move the arrow 10
STORE and press the SELECT (REAR CLICK) BUTTON. When you
have stored the settings, you will seg "OK ?" as a confirmation, Move the
arrow to YES and then press the SELECT (REAR CLICK) BUTTON to
quit.
CUSTOM MODE
ADJUSTMENT DISPLAY 1
| MAC/XGA
TOTAL LINES
FINE SYNC
TOTAL DOTS
HORIZONTAL | a7 ei
| OFF
630
63
a5] a5
1056
SE
Bl
12. To recall the parameter data before settings, move the arrow to RESET VERTICAL 4
and then press the SELECT (REAR CLICK) BUTTON. You can adjust the E
settings again if needed. | E
13. Whenever you want to quit the MENU, point to QUIT and then press the | RESET |
SELECT (REAR CLICK) BUTTON. —
14. If you quit the MENU without storing the settings to the memory, the "STORE |
parameter data you changed will not be kept. | L |
15. The stored settings are permanently kept even if the MAIN ON/OFF is
switched off QUIT
16. Adjust the data such as a "CLAMP", "H-SHIFT", "HEIGHT", "WIDTH",
V-WINDOW" and "V-RAM SYNC" if you needed, move the arrow by ADVANCED
pressing the POINT UP/DOWN BUTTON(s) to select ADVANCED, Press
the SELECT (REAR CLICK) BUTTON,
OK?
ITEM FUNCTION
; When MAC or XGA image is to be projected, select MAC or XGA. For other PC select
MAC/XGA OFF. я
| TOTAL LINES | The number of the total vertical lines. Adjust the number to match your PC image.
FINE SYNC Adjustment of the fine sync to eliminate flicker from the display. a
nat The number of the total dots in one horizontal period. Adjust the number to match your PC |
TOTAL DOTS | "=n ‘
"A Adjustment of the horizontal picture position. When the image is not centered on the
HORIZONTAL | screen, adjust this.
| VERT Adjustment of the vertical picture position. When the image is not centered on the screen,
TICAL adjust this.
17. Another dialog box "CUSTOM MODE ADJUSTMENT DISPLAY 2" will
appear and the parameter data for the MODE you have selected is CUSTOM MODE
shown in this dialog box ADJUSTMENT DISPLAY 2
18. Move the arrow to an item that you want to adjust by pressing the POINT
UP/DOWN BUTTON(s).
19. To increase the level, point the arrow to 5. and then press the SELECT
9
(REAR CLICK) BUTTON. To decrease the level, point the arrow to 77 CLAMP 300
and then prass the SELECT (REAR CLICK) BUTTON.
20. To recall the parameter data before settings, move the arrow to RESET H-SHIFT OFF al
and then press the SELECT (REAR CLICK) BUTTON. You can adjust
the settings again if needed A
21. If you want to store the settings to the memory, move the arrow to HEIGHT 1
STORE and press the SELECT (REAR CLICK) BUTTON. When you
have stored the settings, you will see "OK 7" as a confirmation. Move WIDTH
the arrow to YES and then press the SELECT (REAR CLICK) BUTTON
to quit. A 5
22. Whenever you want to quit the MENU, point to QUIT and then press the AE НЕ Mm
40 =
М
SELECT (REAR CLICK) BUTTON.
23. If you quit the MENU without storing the settings to the memory, the V-RAM SYNC |
parameter data you changed will not be Kept.
24, The siored settings are permanently kept even if the MAIN ON/OFF is RESET
switched off.
| STORE
| —
OK? Tour |
YES a u
ITEM FUNCTION
CLAMP Adjustment of the clamp level. When the image has a dark bar, try this adjustment.
H-SHIFT Coarse adjustment of the CLAMP position. To be adjusted in conjunction with CLAMP,
HEIGHT Expanding or compressing level for the vertical direction.
WIDTH Expanding or compressing level for the horizontal direction.
V-WINDOW | To be adjusted to lessen the skew noise
V-RAM SYNC To be adjusted to eliminate the VRAM noise generated by the partial scan.
= 4 —
(PICTURE IMAGE ADJUSTMENT (COMPUTER MODE) )
Although picture adjustments have been preset at the factory to our standards, you may want to change the setting,
You can make adjustments to the picture image by using either the REMOTE CONTROL UNIT or the TOP
CONTROL of the projector.
1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear.
2. Move the arrow by pressing the POINT UP/DOWN BUTTON(s) to select IMAGE. Press the SELECT (REAR
CLICK) BUTTON. Another dialog box, IMAGE ADJUST DISPLAY will appear, This shows the current picture
settings.
. In this dialog box, you can adjust to increase or decrease the setting levels.
; Move the arrow to an Item to be adjust by pressing the POINT UP/DOWN BUTTON(s).
. To increase the level, point the arrow to À and then press the SELECT (HEAR CLICK) BUTTON. To decrease
the level, point the arrow to “7 and then press the SELECT (REAR CLICK) BUTTON.
6. You may want to store the settings to the memory so that you can recall them later. To store the settings, move
the arrow to STORE and then press the SELECT (REAR CLICK) BUTTON. When you have stored the settings,
you will see "OK 7" as a confirmation.
7. Move the arrow to YES and then press the SELECT (REAR CLICK) BUTTON to quit. The stored settings are
permanently kept even if the MAIN ON/OFF is switched off,
8. If you do not want to store the settings, move the arrow to QUIT and then press the SELECT (REAR CLICK)
BUTTON. The settings changed are temporarily effective until you turn off the MAIN ON/OFF switch.
g. To recall the settings you have stored, move the arrow to RESET and then press the SELECT (REAR CLICK)
BUTTON. You can adjust the settings again if needed.
N + La
MAIN MENU DISPLAY IMAGE ADJUST DISPLAY
[SYSTEM | №» | | BRIGHTNESS 0-63 | 320
| IMAGE + > CONTRAST -
| SCREEN
= 3 | | H-POSITION OK ?
SETTING
—— V-POSITION YES
"LANGUAGE | D ;
- NO
IQUIT =
= STORE
QUIT |
TABLE OF PICTURE IMAGE ADJUSTMENT
BRIGHTNESS DARKER 0-=— 63 BRIGHTER
CONTRAST LIGHTER (| —— 53 DEEPER
H. POSITION RIGHT 0 -—= 255 LEFT
V. POSITION DOWNWARD 0-=-—= 255 UPWARD
(
PICTURE SCREEN ADJUSTMENT (COMPUTER MODE)
This projector have two mode projection "NORMAL" and "EXPANDED for VGA image only as showned below
llustration. This adjustment is available by using either the REMOTE CONTROL UNIT or the TOP CONTROL of the
projector.
NORMAL MODE EXPANDED MODE
600
624
624
800
| 832
1. Press the MODE BUTTON to set COMPUTER MODE.
2, Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear
3, Move the arrow by pressing the POINT UP/DOWN BUTTON(s) to select SCREEN. Press the SELECT (REAR
CLICK) BUTTON. Another dialog box, SCREEN ADJUST DISPLAY will appear
4 To switch to "EXPANDED MODE", move the arrow to EXPANDED by pressing the POINT UF/DOWN BUTTON(s)
and then press the SELECT (REAR CLICK) BUTTON.
5. To switch to "NORMAL MODE", move the arrow to NORMAL by pressing the POINT UP/DOWN BUTTON(s) and
then press the SELECT (REAR CLICK) BUTTON.
The "EXPANDED" setting is temporarily effective until you turn off the MAIN ON/OFF switch.
7. To quit the MENU, move the arrow to QUIT and then press the SELECT (REAR CLICK) BUTTON
©
MAIN MENU DISPLAY SCREEN ADJUST
в DISPLAY
| SYSTEM | > | ==
[ace | » | EXPANDED —#—
| SCREEN <- b | EA -
| SETTING | D QUIT
(LANGUAGE) »
Got"
— 32
)
С
COLOR SYSTEM SELECT (VIDEO MODE) )
This projector is compatible with the four major broadcast video standards: PAL, SECAM, NTSC or NTSC 4.43
(COLOR SYSTEMS). When the color system is set to "AUTO" position, this projector can receive color programs
from one of the 4 systems (PAL, SECAM, NTSC or NTSC 4.43), automatically. However, if the video signal is poor,
the projector may not reproduce the proper video image. In this case, this projector allows you to choose a specific
broadcast signal format. You can select the COLOR SYSTEM by using either the REMOTE CONTROL UNIT or the
TOP CONTROL of the projector.
1.
2
3.
A
CO
Connect the video equipment and the PROJECTOR.
. Press the MODE BUTTON to set VIDEO MODE,
Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear.
. Move the arrow by pressing the POINT UP/DOWN BUTTON(s) to select SYSTEM. Press the SELECT (REAH
CLICK) BUTTON. Another dialog box, COLOR SYSTEM DISPLAY, will appear, The current COLOR SYSTEM is
displayed at the bottom right of the screen.
. If you want to change the COLOR SYSTEM from the current one, move the arrow to the system {hat you want to
select and then press the SELECT (REAR CLICK) BUTTON.
. To quit the MENU, point to QUIT and then press the SELECT (REAR CLICK) BUTTON,
. The setting changed is temporarily effective until you turn off the MAIN ON/OFF switch,
NOTE: The color systems you can select are highlighted in COLOR SYSTEM DISPLAY, Some projectors distributed
in certain areas allow you to select limited systems.
MAIN MENU DISPLAY COLOR SYSTEM DISPLAY
SYSTEM + b> AT e
IMAGE | » PAL
[SCREEN | » | SECAM |
[SETTING | D Met
[LANGUAGE] D _NTSC4.43
| Гашт | PAL-M
= PALM =
| QUIT
SIMPLE METHOD
Es
2,
J.
4.
En
Connect the video equipment and the PROJECTOR.
Press the MODE BUTTON to set VIDEO MODE.
Press the SYSTEM BUTTON on the projector and the COLOR SYSTEM DISPLAY dialog box will appear. The
current COLOR SYSTEM is displayed at the bottom right of the screen.
If you want to change the COLOR SYSTEM from the current one, move the arrow to the system that you want to
select and then press the SELECT (REAR CLICK) BUTTON,
To quit the MENU, point to QUIT and then press the SELECT (REAR CLICK) BUTTON.
. The setting changed is temporarily effective until you turn off the MAIN ON/OFF switch.
23 —
PICTURE IMAGE ADJUSTMENT (VIDEO MODE) 3
Although picture adjustments have been preset at the factory to our standards, you may want to change the setting.
You can make adjustments to the picture image by using either the REMOTE CONTROL UNIT or the TOP
CONTROL of the projector.
1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear.
=. Move the arrow by pressing the POINT UP/DOWN BUTTON(s) to select IMAGE. Press the SELECT (REAR
CLICK) BUTTON. Another dialog box, IMAGE ADJUST DISPLAY will appear. This shows the current picture
settings.
3. In this dialog box, you can adjust to increase or decrease the setting levels.
4. Move the arrow to an item to be adjust by pressing the POINT UP/DOWN BUTTON(s).
5. To increase the level, point the arrow to and then press the SELECT (REAR CLICK) BUTTON. To decrease
the level, point the arrow to “7 and then press the SELECT (REAR CLICK) BUTTON.
6. You may want to store the settings to the memory so that you can recall them later. To store the settings, move
the arrow to STORE and then press the SELECT (REAR CLICK) BUTTON. When you have stored the settings,
you will see "OK 7" as a confirmation.
7. Move the arrow to YES and then press the SELECT (REAR CLICK) BUTTON to quit. The stored settings are
permanently kept even if the MAIN ON/OFF is switched off,
8. If you do not want to store the settings, move the arrow to QUIT and then press the SELECT (REAR CLICK)
BUTTON. The settings changed are temporarily effective until vou turn off the MAIN ON/OFF switch.
9. To recall he settings you have stored, move the arrow to RESET and then press the SELECT (REAR CLICK)
BUTTON. You can adjust the settings again if needed.
NOTE: "TINT will be skipped during in the PAL and SECAM mode.
MAIN MENU DISPLAY IMAGE ADJUST DISPLAY
“SYSTEM —=— > COLOR 0-63
| IMAGE ur es
[SREER ä BRIGHTNESS 0-83 | 326 OK ?
SETTING > A YES
ENACABE! 5 | CONTRAST 0-63 | 32
| QUIT SHARPNESS 0-83 [32 & NO |
| STORE |
‘our |
TABLE OF PICTURE IMAGE ADJUSTMENT
COLOR DECREASES (0-— 63 INCREASES
TINT MORE PURPLE 0 —— = 83 MORE GREEN |
CONTRAST | LIGHTER 0 = 63 DEEPER —
BRIGHTNESS | DARKER )— 63 BRIGHTER
SHARPNESS | SOFTER )— 63 SHARPER
- 34
С
PICTURE SCREEN ADJUSTMENT (VIDEO MODE)
J
This projector has a WIDE function, which enables you to view a wider video image. This adjustment is available by
using either the REMOTE CONTROL UNIT or the TOP CONTROL of the projector,
WIDE function
This projector is designed to project a normal video image (with 4 x 3 aspect ratio). In addition, with the WIDE
function, the projector can project a wider video image by compressing 4 x 3 image. This feature may be used by
those who want to enjoy watching a movie with a cinema-like image. You can switch to either WIDE or REGULAR
screen mode,
1. Press the MODE BUTTON to set VIDEO MODE.
2. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear.
3. Move the arrow by pressing the POINT UP/DOWN BUTTON(s) to select SCREEN. Press the SELECT (REAR
CLICK) BUTTON. Another dialog box, SCREEN ADJUST DISPLAY, will appear. The current screen mode is
displayed at the bottom right of the screen.
4. To switch to "WIDE" mode, move the arrow to WIDE by pressing the POINT UP/DOWN BUTTON(s) and then
press the SELECT (REAR CLICK) BUTTON.
5. To switch to "REGULAR" mode, move the arrow to REGULAR by pressing the POINT UP/DOWN BUTTON and
then press the SELECT (REAR CLICK) BUTTON.
6. The "WIDE" settings is temporarily effective until you turn off the MAIN ON/OFF switch.
7. To quit the MENU, move the arrow to QUIT and then press the SELECT (REAR CLICK) BUTTON.
MAIN MENU DISPLAY
| [SYSTEM
| [IMAGE |
SETTING _
LANGUAGE
QUIT
>
>
[SCREEN + >
»
»
SCREEN ADJUST
DISPLAY
REGULAR |
WIDE +
QuIT
E Е
— OTHER FUNCTION SETTING >
This projector has other function settings; auto retract, reverse 1/8, reverse L/H, blue back, display, mode free and
lamp replace,
AUTO RETRACT
when this function is in the "ON" position, the lens is retracted into lens holder when the projector is turned off. To
protect the lens from the damage while you are carrying the projector, you are strongly recommended to set this
function "ON". Since the lens is retracted in each time the POWER is switched off, you need to make ZOOM and
FOCUS adjustments when you tum on the projector.
REVERSE T/B
When this function is in the "ON" position, the picture
inverted for a ceiling-mounted projector. T /B | INB
REVERSE L/R
When this function is in the "ON" position, the picture |
reversed for a rear projechon.
L/R Йа
BLUE BACK
When this function is in the "ON" position, the projector will project a blue image without video noise on the screen
when the video source is unplugged or turned off.
DISPLAY
When this function is in the "ON" position, on-screen displays always appear when adjustments are made. Although
these on-screen displays are very helpful, these may spoil the view if adjustments are made during presentations.
The certain displays do not appear when display switch is "OFF", The following displays do not appear.
e Count-down Display
* Volume Display.
* Mute Display
e Normal Display ( "DEFAULT" is displayed)
MODE FREE
The MODE FREE function is designed to confirm or clear the parameter data produced by CUSTOM MODE
LAMP REPLACE
The LAMP REPLACE function ls designed to reset the lamp replacement monitor timer. When replace the lamp,
reset the lamp replacement monitor timer for used this function.
AUTO RETRACT, REVERSE T/B, REVERSE L/R, BLUE BACK and DISPLAY
1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear.
2. Move the arrow by pressing the POINT UP/DOWN BUTTON(s) to select SETTING. Press the SELECT (REAR
CLICK) BUTTON. Another dialog box, SETTING DISPLAY will appear.
3. Move the arrow to an item you want to be adjust and the current setting is displayed at the bottom right of the
screen.
4. If you want to change the setting (ON or OFF), press the SELECT (REAR CLICK) BUTTON.
5. To quit the MENU, paint to QUIT and then press the SELECT (REAR CLICK) BUTTON.
6. The settings are permanently kept even if the MAIN ON/OFF is switched off.
MAIN MENU DISPLAY SETTING DISPLAY
SYSTEM | > AUTO RETRACT И ON | a SE
| IMAGE > REVERSE T/B OFF
SCREEN >
| = | REVERSE L/R OFF | =
SETTING + > —— =
TANCIAGE » BLUEBACK | ON |
| А
QuIT DISPLAY | on 6
QUIT
| MODE FREE E
| LAMP REPLACE |p
Arrow to ( 4 ) and press
SELECT ((REAR CLICK)
button,
Arrow to ( 5 ) and press
SELECT ((HEAR CLICK)
button.
— FE
MODE FREE
1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will
MAIN MENU DISPLAY
3. Move the arrow by pressing the POINT UP/DOWN BUTTON(s) to VERTICAL
select MODE FREE. Press the SELECT (REAR CLICK) BUTTON.
via | SYSTEM |
2. Move the arrow by pressing the POINT UP/DOWN BUTTON(s) to select ; JL >
SETTING. Press the SELECT (REAR CLICK) BUTTON. Another dialog :
box, SETTING DISPLAY will appear. IMAGE | >
SETTING DISPLAY SCREEN >
AUTO RETRACT [| ON SETTING 4
m LANGUAGE | №
REVERSE T/B | or [|B ==
ES QUIT
REVERSE L/R | orr |[2 =
BLUEBACK ON || PARAMETER DATA LIST
DISPLAY ON В == |
— MAC/XGA OFF |
QUIT TOTAL LINES | 630
MODE FREE + +
EEE | TOTALDOTS | 1056
ada E НИР HORIZONTAL 47 |
4 |
Another dialog box "CUSTOM MODE LIST" will appear.
4, Move the arrow to one of the "MODEs” that you want to confirm by CLAMP
pressing the POINT UP/DOWN BUTTON(s). Press the SELECT
(REAR CLICK) BUTTON. Another dialog box "PARAMETER DATA H-SHIFT OFF
LIST" will appear.
5. To quit the MENU, point to QUIT and then press the SELECT (REAR HEIGHT
CLICK) BUTTON.
6. If you clear the parameter data, move the arrow by pressing the
POINT UP/DOWN BUTTON(s) to select FREE MODE. Press the WIDTH
SELECT (REAR CLICK) BUTTON. You will see "OK?" as a
8
E
—
confirmation. V-WINDOW | 0
7. Move the arrow to YES and then press the SELECT (REAR CLICK) ——
BUTTON, the parameter data is clear and MENU is quit. V-RAM SYNC 40
CUSTOM MODE LIST
MODE 1 | STORED —+- > TEN = =
MODE 2 | FREE | >
MODE3 | FREE _ » |
MODE 4 | FREE | > OK ?
MODE 5 | FREE | >»
MODES | FREE | >
MODE7 | FREE | D Ме ||
MODES | FREE —D
ET
—
LAMP REPLACE
NOTE: The LAMP REPLACE MONITOR must be reset only after the lamp has
been replaced by a new one. Do not forget to reset the LAMP
REPLACE MONITOR after replacing the lamp, so the projector can
keep track of the usable life of the new lamp.
1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will
MAIN MENU DISPLAY
appear.
2. Move the arrow by pressing the POINT UP/DOWN BUTTON(s) to select SYSTEM >
SETTING. Press the SELECT (REAR CLICK) BUTTON. Another dialog box, Ty E
SETTING DISPLAY will appear. | IMAGE | >
3. Move the arrow by pressing the POINT UP/DOWN BUTTON(s) to select LAMP ]
REPLACE and then press the SELECT (REAR CLICK) BUTTON. When you | | SCREEN | №
reset the lamp replace monitor, you will see "RESET?" as a confirmation. Te Ч ‘
4, Move the arrow to YES and then press the SELECT (REAR CLICK) BUTTON. | SETTING i LA
The lamp replace monitor is reset and MENU is quit. | LANG UAGE | >
5. Move the arrow to NO and then press the SELECT (REAR CLICK) BUTTON, ae ранен
The lamp replace monitor is not reset and MENU is quit. | QUIT
SETTING DISPLAY
AUTO RETRACT | ON |
REVERSE T/B | OFF |
Ja [ar A ~ LAMP REPLACE MONITOR
REVERSE L/R | off |g rn pin
BLUEBACK on | RESET? [YES
DISPLAY “on | 7
QUIT |
| MODE FREE +
LANGUAGE ADJUSTMENT
You can select a language used in the MENU among English, German, French, Italian ano Spanish. This adjustment
is avallable by using either the REMOTE CONTROL UNIT or the TOP CONTROL of the projector.
1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear.
2 Move the arrow by pressing the POINT UP/DOWN BUTTON(s) to select LANGUAGE. Press the SELECT (REAR
CLICK) BUTTON. Another dialog box, LANGUAGE SETTING DISPLAY, will appear.
3. Move the arrow to the language you want to use by pressing the POINT UP/DOWN BUTTON(s) and then press
the SELECT (REAR CLICK) BUTTON.
4 To quit the MENU, move the arrow to QUIT and then press the SELECT (REAR CLICK) BUTTON.
5. The setting is permanently kept even if the MAIN ON/OFF is switched off
NOTE: The languages you can select are highlighted in LANGUAGE SETTING DISPLAY. Some projectors
distributed in certain areas allow you to select limited languages.
MAIN MENU DISPLAY sertie ab
SYSTEM | > _ ENGLISH + ||
(MAGE | + (DEUTSCH | —
[SCREEN | D | FRANCAIS
| SETTING » [ITALIANO
LANGUAGE+— b> | ESPANOL |
QUIT | [’auIT
— 40
[8 AIR FILTER CARE AND CLEANING 5
The removable the air filter prevents dust from accumulating on the surface of the projection lens and projection mirror.
Should the air filter become clogged with dust particles, it will reduce the cooling fan's effectiveness and may result in
internal heat build up and reduce the life of the projector.
To clean the air filter, follow the cleaning procedures below:
1. Tum the POWER (LAMP) ON/OFF button CFF.
2. Remove the air filter caver.
Carefully place a coin against the indented part of the filter cover and lift.
3. Remove the air filter from the filler cover.
4. Clean the air filter with a vacuum cleaner.
5. Replace the air filter, Make sure that air filter cover is securely insertad.
Do not clean with water, Doing so may damage the air filter.
Do not operate the projector with air filter removed,
AIR FILTER
COVER
RECOMMENDATION
TO ENJOY PICTURE IMAGE, USE THE PROJECTOR IN
THE CLEAN ENVIRONMENT, USAGE IN THE CLEAN
ENVIRONMENT 15 RECOMMENDED.
When used under the dusty or smoky conditions, dust may
accumulate on the liquid crystal panel and lens inside it, and may
resultantly be projected on the screen together with the picture.
When the above symptoms are noticed contact the place where your COVER
authorized dealer or service station for the cleaning.
AIR FILTER
( TEMPERATURE WARNING INDICATOR )
The TEMPERATURE WARNING INDICATOR flashes red whan the internal
temperature of the projector exceeds tha normal temperature.
Possible causes for the temperature warning may be:
1. Ventilation slots of the projector are blocked. In such an event, reposition the
projector so that ventilation slots are not obstructed.
2. Air filter is clogged with dust particles. Remove dust from the air filter by
following instructions in the Air Filter Care and Cleaning section above.
If the TEMPERATURE WARNING INDICATOR still continues to flash after
checking (1) and (2), call your authorized dealer or service station,
TEMPERATURE
WARNING
INDICATOR
— UA
( LAMP REPLACEMENT
If the lamp fails to come on and the lamp monitor on the projector light is orange, you must replace the lamp.
* For continued safety, replace with a lamp assembly of the same type.
* Allow the projector to cool for at least 45 minutes before you open the lamp cover. The
inside of the projector can become very hot.
s Do not drop the lamp module or touch the glass part ! The glass can shatter and cause
injury.
* To prevent operator injury, the lamp cover is locked. Unless the guard is in the unlocked
position, the lamp cover will not disconnect even if the screws have been removed.
Sr : Mo - y
Follow these steps to replace the lamp assembly.
. Turn off the projector and allow the projector to cool thoroughly.
. Disconnect the AC cord from the projector and slide the guard to the unlock
position.
‚ Remove 2 screws with a screwdriver and disconnact the lamp cover
. Remove 2 screws with a screwdriver and pull out the lamp assembly Dy
grasping the handle,
5. Replace the lamp assembly.
6. Tighten 4 screws to secure the lamp assembly and lamp Cover.
7. Slide the guard to lock the lamp cover.
В. Connect the detachable AC cord to the projector. LAMP REPLACEMENT
INDICATOR
>> UNLOCK
Ls LS A3 —
POSITION
LAMP LE,
GUARD — LOCK ASSEMBL Y
POSITION
9. After replacing the lamp, you must reset the LAMP REPLACEMENT MONITOR TIMER. (See "LAMP REPLACE
section on page 39.)
NOTE: Do not reset the LAMP REPLACEMENT MONITOR TIMER, except after the lamp replacement.
(
CLEANING THE LENS
Follow these steps to clean the projection lens:
1. Use a non-abrasive camera lens cleaner with a soft, dry cleaning cloth.
Avoid using an excessive amount of cleaner.
Abrasive cleaners, solvents or other harsh chemicals might make scratch on the lens.
2. Lightly wipe the cleaning cloth over the lens.
3. If you don't intend to use the projector immediately, replace the lens cover.
К
TROUBLESHOOTING
Problem:
Try these Solutions:
No power
® Plug the projector into an AC outlet.
e Tum the MAINS ON/OFF button to ON,
e Be sure the READY INDICATOR light is ON,
NOTE: After pressing the LAMP POWER ON/OFF button to
OFF . The projector functions as follows.
1. The LAMP POWER indicator will light and the READY
indicator will turn off.
2. After one minute, the READY indicator will light green again
and the projector can be tumed on by pressing the LAMP
POWER ON/OFF button.
e Check temperature warning indicator. If the indicator flashes
red, the projector cannot be turned on.
(See "USING THE PROJECTOR" section on page 24).
# Check the projection lamp.
No image
e Check if computer or video cables are connected to the
Projector and the computer or vidéo equipment.
e Check the color system. (Video Mode).
as Check the computer system. (Computer Mode).
e Make sure you have removed the lens cover,
Image is out of focus |
* Adjust the focus,
® Маке sure the projection screen is at least 3.6 feel (1.1 m)
from the projector.
e Check ifihe projection lens is dark.
NOTE: Moving the projector from a cool temperature location
to a warm temperature location may result in moisture
condensation on the lens. In such an event, leave the
projector OFF and wait until condensation disappears.
— dy —
Problem:
Try these Solutions:
Picture ls L/R Reversed.
Check REVERSE L/R feature.
(See "OTHER FUNCTION SETTING" section on pages 36 —- 37).
Picture ls T/B Inverted.
Check REVERSE T/B feature.
(See "OTHER FUNCTION SETTING" section on pages 36 ~ 37).
Some displays are not seen
during the operation.
Check DISPLAY feature.
(See "OTHER FUNCTION SETTING" section on pages 36 o 37). 3
No sound.
a Check audio cable connection from audio input source.
e Check the audio source.
a Press the VOLUME (+) button.
e Press the MUTE button.
Remote control unit doesn't
Work,
e Check the batteries.
eMake sure nothing is blocking between the remote control
sensor and remote control unit.
e Make sure you are not too far from the projector when using the
remote control unit. {Maximum operate range 16.4 feet (5 m)}.
Wireless mouse function does
not work.
e Check the cable connection between the projector and the
computer.
e Check the mouse setting on your computer.
e Turn on the projector before vou turn on the computer,
Е TECHNICAL SPECIFICATIONS )
SPECIFICATIONS
Projector Type | Multi-media Projector
Dimensions (H x W x D) | 5.9" (148.9 тит ) x 11.6" (296 mm) x 18.1" (460 mm) =
Net Weight | — 16.0165 (7.2 Ко) 3
LCD Panel System | 1.3" TFT Active Matrix type ( Thin Film Transistor) * 3
Number of Pixels — 1,557,504 (519,168 (832 x 624) x 3}
Color System | 4 color system (NTSC, PAL, SECAM and NTSC4.43) |
Scanning Frequency H-sync. 15 ~ 58 KHz, V-sync. 50 ~ 75 Hz |
Projection Image ‘ Size (Diagonal) Adjustable from 20" to 400"
Contrast Ratio | 1001
Horizontal Resolution 750 TV lines
Projection Lens F2.5 — 3.2, 11.77" - 2,95 with Motor zoom and focus
Throw Distance | 3,6 (1.1 m) - 75.6' (23.0 m)
Projection Lamp Metal Halide, 250 watt type
Projection Mirror | Dichroic mirror and X- -prism system
Е. AV Input jacks RCA Type > 3 (Video, Audio R and L) and DIN 4 pin (S-Video) = 1
Computer Input Jack = (VGA) HDB15 Terminal * 2, Multi- -pole 12 pin (Control port)
Monitor Output Jack — (VGA) HDB15 Terminal x 1
Computer Audio Input Jack Mini Stereo Type x 2
Video Monitor Output Jack RCA Type = 1
Audio Monitor Output Jacks RCA Type = 2 (Rand L)
Other Jacks EXT. Speaker Jack 1
Bullt-in Speaker | (2) 4 cm * 7 cm, Stereo (R and L), 3 watt + 3 watt (Music Power)
Image Elevation Adjustment | Uptos'
__ Voltage | 100 ~ 120V AC, 50/60 Hz
Power Consumption 5.0A (Max. Ampere)
Operating Temperature 5C-35C
Storage Temperature | 10% - 60 C
Remote Control Battery (2) AA Type
This symbol on the nameplate means the product is Listed by Underwriters Laboratories Inc.
It is designed and manufactured to meet rigid U.L. safety standards against risk of fire. casualty
and electrical hazards.
_= йе
EIK]
Audio Visual/Video Products
EIKI INTERNATIONAL, INC.
26794 Vista Terrace Drive, Lake Forest, CA. 92630-8113
TEL (714) 457-0200 FAX (714) 457-7878
IN CANADA, EIKI CANADA
355 Cranston Crescent P.O. Box 156
Midland Ontario L4R 4K68 Canada
TEL (705) 527-4084 FAX (705) 527-4087
Printed in Japan
Part No. 510 267 2923 (1AA6P1P1219-- M6FBA) (© 1997 Eiki International, Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising