OWNERS MANUAL
MS SERIES
STEREO MIXING S YSTEM
WARNING: TO PREVENT ELECTRICAL SHOCK OR FIRE HAZARD, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE. BEFORE USING THIS APPLIANCE,
READ THE OPERATING GUIDE FOR FURTHER WARNINGS.
2007-15 ESTER
MIO —a) FREQ
| +10 de
GE oa
+ 10 =— | —
+ ® — —
46 — ===
+ —
— —
а LL Bu
16
CHANNELS
GAIN
Varies the gain of the channel input stage to allow a wide input dynamic range. Calibration is in dB from approximately 2
dB to over 60 dB. Proper adjustment of the input gain is aided by observance of the LED STATUS DISPLAY.
MONITOR SEND A/B
Two monitor sends are provided in a dual-concentric control. The inner knob is Monitor A, the outer knob is Monitor B.
Both sends are "Pre EQ" and “Pre Fader", meaning before equalization and before the channel fader. Both sends are
independent of all channel functions except the gain control, allowing adjustment of the “house” mix without affecting the
monitor mixes.
HIGH FREQUENCY EQ
An active tone control (shelving type, +15 dB) that varies the high frequency range.
MID/FREQUENCY EQ
The inner “mid” control is capable of 15 dB of boost or cut at the center frequency selected by the outer “FREQUENCY”
control. Frequency range is 200 Hz to 5 kHz,
LOW FREQUENCY EQ
An active tone control (shelving type, +15 dB) that varies the low frequency range. Caution: excessive low frequency boost
causes greater power consumption and increases possibility of speaker damage.
EFFECTS SEND, A/B
Two effects sends are provided in a dual-concentric control. The inner knob is Effects A, the outer is Effects B. Both sends
are Post (after) EQ and Post Fader. The “A” send supplies the Effects A master control and the internal reverb. The “B" send
supplies the Effects B master control and the internal electronic delay.
PAN
Used to place the channel signal in full left or full right or anywhere between. For some applications it may be used as a
rotary channel assignment control allowing assignment to the Left or Right sliders.
PFL (PRE FADE LISTEN)
Allows cueing of any channel or combination of channels instantly through headphones connected to the HEADPHONE
jack (master section), or via a powered monitor connected to the PFL AUX. (See Auxiliary Inputs.)All channel functions
(except fader) may be monitored via the PFL system.
LED STATUS DISPLAY
Indicates the operational state of the channel. The green -10 dBV (.32V RMS) LED indicates that the channel is active. The
red +10 dBV (3.2V RMS) warns that overload could occur. Since the channel is capable of +18 dBV, there is still 8 dB of
headroom available when the red LED flashes,
The sampling for status indication is taken at three critical points (after the input amp, equalization and final channel gain
stage). Proper channel adjustment should allow the +10 dBV LED to flash only on extreme peaks in the program material.
CHANNEL LEVEL SLIDER
Determines the level of the channel. Calibration isin dB and level is variable from “infinity” (off) to +10 dB. This should be
operated near the "0 dB” (unity gain) indicator whenever possible to assure an optimum balance between channel noise and
headroom.
Operation Note, Channel Level Slider
Sometimes it may be necessary to operate the slider at other than this optimum setting. Example: If the channel need not
be as loud as the other channels, the slider may be set lower than 0 dB. This yields lower noise and a visual indication of the
channel's relative level. Should more level be needed, it can be achieved with the slider, preventing readjustment of the
critical input gain, which would also affect the monitor sends.
MON. ASEFX. à
MOM. B/EFX. B
+
+в
+2
о
=3
=B
=F
“17
=15
=18
= Fi
a —
WON. AB m EF. AB
MONITOR A
53 125 250 Eta 1K
IH ЯК E 18H
OUTPUT LEVEL (dB)
DISPLAY SELECT
LEFT:RIGHT
+
LEFT/FFL
ña 175 250 50
RIGHT/MASTER
+5
+1
9
=
-6
-#
=17
15
‘a
POWER
=
PAL:MASTER
MONITOR E
1K IK AK BE TE
EEE EEE
= TEES a wu |
12 = EF 1 — — | — NN Pl P. Ya m |2 === |
LE] 125 50 50% IK
LEFT
da 129 250 00 E FL] AK ax TEN
+
> 4K HS тен.
83 is 250 50 ik 2H
RIGHT
“3 135 150 6 ik FL
4K BK IEE
“к aK VE
SERRE ZEEE EEE
= HEE CE EEE.
SE dar = ЕЕВНЕВЕЕЕ
El 125 250 FM = aw ER a
EFFECTS A EFFECTS B/DELAY
RETURN RETURN
a Un 0 16
LEVEL + PAR LA LEVEL-— FAN L/A
ree Ш pe. |
MONITOR
{0 ee ff —— a —— ff —
1 —. ooioo +4 —o
в — o 6 — ————
SE AE
i — E —— ‹— NN <—
¿Mask Ed A
E —ÍÑ — —_— |
ле —
wl -п = IL —
MON. A MON. B
Master Section
REVERE
RETURN
5
O
a 16
TO MON. AB
O
0 19
LEVEL -—-PAM L/A
LEFT
* “
= О 10
EFFECTS
MASTERS
= 00 id+
EFE AE EFI E
+
= я
©
о 0
DELAY <&-HEPEAT
ELECTRONIC
CELAY
RIGHT
53 125 860 50) IK mM LL] aK 16K
AUXILIARY
OUTPUTS
+ 5 я
* a
O
o 10
STEMES OUT
5
1 a
a a
O
в 10
PFL LEWEL
HEADPHONE 7
HÉAGPHÔHE
PFL ACTIVE
+10
MASTER
LAMP
1T AC
MASTER SECTION
MONITOR A/B SLIDERS
These are the masters for all channel A and B Monitor sends and
determine the overall monitor mix levels.
MAIN LEFT/RIGHT SLIDERS
These are the masters for all channels and determine the overall main
or “house” mix levels.
MASTER SLIDER
Controls the overall mix level when the mixer is operated in the mono
configuration (2X1). “Master” is the combination of the Main Left and
Right signals after the graphic equalizers. (See Master Out.)
MONITOR A/B GRAPHIC EQUALIZERS
These 9 band, one octave equalizers are electrically between the MON-
ITOR level sliders and the MONITOR BALANCED LINE outputs allowing
independent equalization.
Operation Note, Graphic In/Out
Graphic IN and OUT jacks are provided to allow use of the equalizers
for other purposes if desired. (See Monitor A/B, Graphic In/Out)
LEFT/RIGHT GRAPHIC EQUALIZERS
These 9 band, one octave equalizers are electrically between the LEFT
and RIGHT level sliders and the MAIN BALANCED LINE outputs provid-
ing independent equalization for each side of the stereo mix.
Operation Note, Graphic In/Out |
Graphic IN and OUT jacks are provided to allow use of the equalizers
for other purposes if desired. (See Right/Left, Graphic In/Out)
EFFECTS MASTERS (A/B)
The inner knob is the Effects A Master, the outer is the Effects B Master.
The Effects A Master determines the effects level supplied to the internal
reverb andthe Effects A output jack. The Effects B Master determines the
effects level supplied to the internal electronic delay and the Effects B
output jack. (See Effects Patch diagram.)
ELECTRONIC DELAY/REPEAT
The Delay control adjusts the delay time and is variable from 13 to 185
milliseconds. The Repeat control varies the signal regeneration or
number of “repeats” in an echo effect. These controls operate together
with the Effects B Master and the Effects B/Delay Return controls.
Operation Note
Selectthe EFX B LED ARRAY to monitor the Delay drive level. Exceed-
ing +6 dB would distort the delayed signal.
REVERB RETURN (LEVEL)
Controls the reverb effects supplied to the Left and Right Mains. This
must be used together with the REVERB RETURN (PAN) control.
REVERB RETURN (PAN L/R)
Allows the reverb effect to be assigned to Left Main, Right Main or both.
REVERB RETURN (TO MONITOR A/B)
Allows the reverb effect to be assigned to Monitor A and Monitor B.
EFFECTS A RETURN (LEVEL)
When an outboard effects device is connected into the Effects A patch
loop, this control regulates the intensity or level of the effect in the Left
and Right mix. This control must be used together with the associated
PAN control.
EFFECTS A RETURN (PAN)
Allows the "A" effects return to be assigned to Left Main, Right Main or
both.
EFFECTS A RETURN (TO MONITOR A/B)
Allows the “A" effects return to be assigned to Monitor A and Monitor B.
EFFECTS ‘B”/DELAY RETURN (LEVEL)
Regulates the level of the internal Electronic Delay and must be used
together with the associated PAN control.
NOTE:When an outboard effects device is connected into the Effects
B patch loop, the internal delay is disconnected and this control
regulates the level of the outboard effect in the Left and Right mix.
EFFECTS B/DELAY RETURN (PAN)
Allows the "B" effects return orthe Electronic Delay to be assigned to
Left Main, Right Main or both.
EFFECTS B/DELAY RETURN (TO MONITOR A/B)
Allows the “B” effects return orthe Electronic Delay to be assigned to
Monitor A and Monitor B.
AUXILIARY QUTPUTS (STEREO OUT)
Adjusts the Left and Right signal level to the STEREQ OUT jack (patch
panel). Signal for this control is taken before (PRE) the Left and Right
Main sliders.
AUXILIARY OUTPUTS (PFL LEVEL)
Controls the level for any “Pre Fade Listen" (PFL) source selected on the mixer. One or more PFL switches must be engaged before this control is
active (the PFL ACTIVE LED will light).
PFL (MASTER)
These four switches allow cuei
HEADPHONE jack.
PFL ACTIVE
The LED is illuminated when any PFL switch is activated.
LAMP
ng of the Monitor Masters (A and B) and/or the Main (Left and Right) through headphones connected to the
A special 2-pin XLR jack is provided for connecting an optional gooseneck mixer lamp (model ML-2) for illumination in adverse lighting
conditions.
LED ARRAYS (MONITOR A/EFFECTS A, MONITOR B/EFFECTS B, LEFT/PFL, RIGHT/MASTER)
Four calibrated, switch-selectable, 10 segment LED arrays are provided to visually indicate the levels of the mixes selected.
DISPLAY SELECT
The position of each switch determines which signal sources will be displayed.
CH. 15 & 16
= © ®©
SOURCE
NORMAL IL
PHONO —
SEND RETURN
REAR PANEL (CHANNELS)
LINE IN
A high impedance (40k ohm), %" jack which will accept signal sources up to +36 dBV (60V RMS).
LOW Z IN
16 For use with low impedance microphones or low level sources equipped with an XLR connector.
LIME IH
| PHANTOM POWER
Operation Note
This input will accept up to +16 dBV (6.3V RMS). An additional 20 dB pad can be provided by inserting an “open” stereo
phone plug into the Line In jack.
SEND AND RETURN
These jacks allow individual channel patching after the Input Gain control and before the channel equalization (Pre EQ).
The SEND may be used to patch from the channel without interrupting the channel signal path. The RETURN is a switching
jack which interrupts the normal signal path allowing external signal processing equipment to be patched “in-line” with the
channel.
PHANTOM POWER ON/OFF
These switches allow on/off selection. of the 48V DC phantom power in groups of four channels.
RIAA PHONO INPUTS
The last two channels may be operated as phonograph inputs by selecting the
"PHONO” position of the NORMAL/PHONO switch. In the PHONO mode, both channel inputs (11 and 12 on MS-1221, 15
and 16 on MS-1621, 23 and 24 on MS-2421) are rerouted to the phono jacks near the Master Patch Panel.
Both units are specially equalized (RIAA EQ) and do not require an outboard RIAA equalizer/preamp. When the PHONO
mode is selected, the channels Line In and Low Z inputs are disabled.
NOTE:Other equipment such as tape decks do not usually require RIAA equalization and should be patched directly to
the channel inputs.
OM
OFF
«if VOLTS —
STEREO OUT
— CAQSS0OVER —
HIGH HIGH
{PAD & EQ.)
©
1200
800 Г LOW
"
FREG.
INPUT
MASTER
MASTER OUT
LINE IN
MASTER IN
GRAPHIC QUT
GRAPHIC IN
R OUT L
— RIGHT —— LEFT — |
MASTER LEFT
AUXILIARY INPUTE —
EFX A
EFX. E
GRAPHIC OUT
GRAPHIC IN
MON. OUT
REY. —
PATCH FOR EFFECTS DEVICES
Effects Hookup is typical for Delay units, Phasors, Flan-
gers, Chorus units, etc. The “A” Effects loop is illustrated.
“B” may be patched in the same manner.
NOTE: Effects devices used with this system should be
“line-level” products to work satisfactorily.
@
EFFECTS OUT
MASTER PATCH PANEL ——————
Shielded Cable
Shielded Cable
о о
© ©
о INPUT OUTPUT о
EFFECTS
DEVICE
REAR PANEL (MASTER)
AUXILIARY INPUTS
May be used to patch an external signal into any of the eight mix buses: Master, Left, Right, Monitor A, Monitor B, Effects A, Effects B and PFL.
These inputs are primarily provided for patching an auxiliary sub mixer to gain additional channels.
Operation Note
The PFL Auxiliary input, normally used to patch the PFL systems oftwo mixers together (via a shielded stereo cable), may also serve as an extra
“PFL mix" output or to drive a powered monitor (or equivalent). For this application use a shielded cable with a stereo 14” phone plug (leave the ring
“open”) so the PFL switching will remain active.
STEREO QUT
This 14” stereo (ring-tip-sleeve) jack provides a stereo output from the LEFT and RIGHT Mains before the sliders and before the graphic
equalizers. This output level is adjusted by the STEREO OUT control (Master Section).
RIGHT/LEFT (LINE IN)
These switching jacks allow insertion of signal processing equipment “in-line” with the Rightand/or Left Mains. They also provide directaccess
to the line driver stages ahead of the Left and Right Balanced Line Quts. (See Mono Operation Patch Diagram.)
RIGHT/LEFT (MASTER IN)
These inputs are similar to the Right/Left Line Inputs, except they provide direct input to the Master summing section. These are switching jacks
which interrupt the normal signal path to the Master. These inputs are useful for inserting external signal processing equipment “in line” with the
Right and/or Left Mains. They also allow the graphic equalizers to be bypassed if desired.
RIGHT/LEFT (GRAPHIC IN/OUT)
Both graphic equalizers can be patched into other signal paths by using these jacks. The IN (switching) jacks allow the graphic to be switched
away from its normal input, to accept an external signal to be equalized. This allows the internal equalizers to be used as if they were outboard
graphic equalizers.
RIGHT/LEFT (OUT)
These outputs are from the Right and Left Mains beforethe graphic equalizers. These jacks are useful for bypassing the equalizers, if desired, by
patching the Right/Left Outs directly to the Right/Left Line Inputs, or direct to the Master (via the Master Inputs).
MONITOR A/B (GRAPHIC IN/OUT)
Both graphic equalizers can be patched into other signal paths by using these jacks. The IN (switching) jacks allow the graphic to be switched
away from its normal input to accept an external signal to be equalized. This allows the internal equalizers to be used as if they were outboard
graphic equalizers.
MONITOR A/B (MONITOR OUT)
These outputs are from the Monitor A & B before the graphic equalizers. These jacks are useful for bypassing the equalizers, if desired, by
patching the Monitor A/B Outs directly to the Monitor A/B Line Inputs.
MONITOR A/B (LINE IN)
These switching jacks allow insertion of signal processing equipment “in-line” with the A and/or B monitors. They also provide direct access to
the line driver stages ahead of the Monitor A and B Balanced Line Outs.
MASTER OUT
This output is a “mono” combination of the Left and Right program material after the equalization. The level is adjusted by the Master Slider.
Operation Note
In mono operation, a “balanced” line output is often needed to patch to the power amplifiers on stage. This can be achieved by patching the
Master Out to one of the Line (Right or Left) Inputs and then using the associated Balanced Line Output. (See Mono operation patch diagram.) The
Master Out jacks may be used to patch to the power amplifier(s) if they are near the mixer or if balanced lines are not otherwise required.
EFFECTS A/B (OUT, RETURN)
These are the Effects patch loop connections for the two internal effects buses. The Effects Out is for patching to the input of an outboard effects
device. Next, patch the effects device output to the respective Effects Return. (See Effects Patch diagram.)
REVERB FOOTSWITCH (REV./F.S.)
The reverb may be remotely selected, on or off, by a simple footswitch (optional) and will affect only the reverb function. For proper operation, the
footswitch plug should only be inserted to the first detent or “click” of the jack. Full insertion will completely override the reverb function.
NOTE: This jack may also be used as a third Effects Return. For this function, the return cable plug should be fully inserted into the footswitch
jack. In this mode, the REVERB RETURN control in the Master section controls the level of the third effect.
DELAY PATCH
This stereo switching jack allows the internal Electronic Delay to be “removed” from the Effects "B” bus and patched to other sends and returns
as if it were an outboard delay device. It is necessary to use a shielded stereo “Y" cable. The “tip” accesses the Delay input, the “ring” accesses the
Delay output.
NOTE:Only delayed signal is available at this output.
CROSSOVER INPUT
The electronic crossover is internally patched to the Master Output, however, the INPUT jack is of the switching type, which allows another
source to access the crossover if desired.
CROSSOVER FREQUENCY
The internal crossover is designed to provide an 18 dB per octave frequency dividing function, and three crossover points are selectable. The
crossover point selected should be determined by the speakers or speaker/horn combinations used in your system. (See your speaker enclosure
specifications.)
CROSSOVER (LOW)
This is to be patched to the “low pass” power amplifier input. (See crossover patch diagram.)
CROSSOVER (HIGH)
This is to be patched to the "high pass” power amplifier input (See crossover patch diagram).
CROSSOVER (HIGH (PAD & EQ))
This is to be patched to the "high pass’ power amplifier if the high frequency component of the speaker system uses a Peavey Model 22A driver.
The HIGH EQ output provides special mid frequency pad and high frequency boost to maximize the response of the model 22A driver. (See
crossover patch diagram.)
BALANCED LINE OUT (MAIN L/R, MONITOR A/B)
All four are transformer balanced, XLR outputs to allow quiet operation even with long multi-conductor snake cables.
Operation Note
Any signal may be sent to the balanced outputs via its respective Line In jack. Patching to the Line Inputs will disconnect the normal signal path to
the balanced outputs. (See Master Out.)
— RIGHT = LEFT == p—————— AUXILIARY INPUTS —————
© © © © © Rear Panel (Master)
one o o © @ ® ©
RIGHT MON, 6 EFX.B
HIGH HIGH ey — DELAY Ë
{PAD & ECL}
00070
LOW GRAPHIC QUT
500
GRAPHIC OUT
INPUT
GRAPHIC IN
MASTER GRAPHIC IN RETURN
MASTER OUT я OUT L MON. OUT EFFECTS OUT
MASTER PATCH PANEL — |
MAIN MONITOR MONITOR
BALANCED LINE CUT LIME IM BALANCED LINE OUT
POWER GMD. 120 VAL
ON + ED Hz ©
RIGHT LEFT B A B A
POWER SWITCH
Depress to “On” position to turn on.
GROUND SWITCH
Three position rocker type switch which, in most applications, should be operated in its center or zero position. There may be some situations
when audible hum and/or noise will come from the loudspeaker. If this situation arises, position the ground switch to either positive or negative
(+ or -) or until the noise is minimized.
NOTE:Should the noise problem continue, consult your authorized Peavey dealer, the Peavey factory, or a qualified service technician. THE
GROUND SWITCH IS NOT FUNCTIONAL ON 220/240 VOLT MODELS.
LINE CORD
For your safety, we have incorporated a 3-wire line (mains) cable on the back of the chassis with proper grounding facilities. It is not advisable to
remove the ground pin under any circumstances. If it is necessary to use this equipment without proper grounding facilities, suitable grounding
adaptors should be used. Less noise and greatly reduced shock hazard exists when the unit is operated with the proper grounded receptacles.
NOTE:The above statement in reference to removing the ground pin is applicable only to 120 volt model products.
TO LED /
ÉFR À OISPLA
о ALE.
| k D HOM 17 ID din] ] wi amy
B oC la ram CFE & EFX A SEND a AMP NEY PAN мамы
MASTER y "m6 “es L
Bi с aug
fetta be] MAH
EEL RE - у
А ONéIRHO | LINE AWF HIE id
sus AME o ri y MON. A NUS
REY TO Mk BBE
Г — C= - ] мон п
ЕЕ В АИ.
HOM AV Gans
TO LED
CISELY
GAIN AUP „ PAN WAIN EFL B EFX%. 8 SEND
| MEX. 29 (+6 de) EFE RET L MASTER на лу 10 dBW)
AC. 14 о оО му у eus LD 254 1012 Oi
FFE HET iN
JA & Bi MA
| Bus: | в COMENCE LINE AR
EEx. For У A sur
нон. & | RON, E BUS | Bus Pag
EFE. ro
| Ere ro и мен B BUS
bus — — . = я
| Ç T ETD STATUE STATUS |
CO Z INPUT E so " Таити LEDS GAIN ANF LEDS РАН
Máx Fe C+6 08m ! | MAINE
| ме. лаве 1-14 2800 отм y ¥ 7 y St Pr У BUS |
[ETE ET LT:
HOM EIN di pe male À | pete
мир HEGH EATER ENE A
LIME | PUT
MAK EV (+74 CM] EFO A BUS
HOM 1% 4D dai
| Min. 10m ed cE] | i
EFX 6 SUS |
TYPICAL EACH CHANNEL FED | |
| TELE ]
ALR. EE DIA LINE AMP MAIN LEFT
ном: то ап FAOEA
REPT IN ANT GRAPHIC SLT LIME IN
DUT
137 Ami MAX 9% [+37 dimi
| Ma NI ia peu WO TY 1d AY
COMMING LINE AMP
me AMP
MEIN |
"ys CED LIME OUT |
MÄR Sa fim
ELECTRO AA CRIOGRDYVER
{БАМ 45 MAIHLEFT I | | (SAME 4% Méir LEFTI ¡SAME A5 MAIN LET
MASTER 3} _ MASTER
HÔW Te i 2 | amena Diéplan SE Paba:
ARP LIKE BRE | E
FREOPER
IHPUT SELECT
WAIN a) м > WAX AW [533 dO AH CE Hi HIGH
MASTER |” HOM. 1Y 10 6ÉVI AD ia CE
nam Ч da. FADER
MASTER AUX IH
FOR 1% 0 afl |
Г o ны pe si — — —- =" =" —- — —
|
| MAIN RIGHT |! MONITOR B MONITOR A
В _ == E Ea A SI EL CE Ч
— RIGHT — LEFT —
© © @
LINE IN
MASTER IN
GRAPHIC QUT
GRAPHIC IN
A OUT L
MASTER
AUXILIARY INFUTS —————
MASTER
STEREO CUT
—— CROSSOVER —
HIGH
LEFT MON A
PFL
RIGHT
(PAD $ Lo. } BE MON.
GRAPHIC OUT
GRAPHIC IN
MON. OUT
INPUT
MASTER
© ©
MASTER bor
FREQ.
EFFECTS OUT
PATCH PANEL |
Shielded Cable
PATCH FOR MONO OPERATION TO GET A
BALANCED
LINE OUT.
Since the Right and Left “Line In” jacks give direct access
to the Right and Left line driver stages (switched), a trans-
former balanced output can be achieved for the Master
Out by completing this patch. The balanced Master Qut
signal is then taken at the “Right-Main” Balanced Line Ош!
jack as illustrated. The Monitor line drivers can be used in
the same manner by using the Monitor A or B “Line In” and
the Monitor A or B Balanced Line Outs.
NOTE: Any output from the MS™ Mixer can be “balanced”
using this method.
e
RIGHT
MAIN
BALANCED LINE OUT
LEFT
MONITOR
LIME IN
MONITOR
BALANCED LINE CUT
® ©
To power amp rack
(through snake, if used)
CROSSOVER PATCH DIAGRAM
STERED QUT
Shielded Cable — CROSSOVER ——
High Pass E Boiss mr td uno mu ee de E
Channel
HIGH HIGH
[PAD 5 EC)
Shielded Cable
1200
Low Pass
Channel
FREG.
©
MASTER
| |
Ste reo MASTER OUT
Power
— RIGHT —— LEFT —
LINE IN
MASTER IN
GRAPHIC OUT
GRAFHIC IN
MASTER LEFT
RIGHT
— AUXILIARY INPUTS
MON. A
MON. E
o
EF. A
EFX. B
A OUT L
—— 6 MON.
GRAPHIC OUT
GRAPHIC IN
A —
MON. OUT
— DELAY
PATCH
REY.
=
FT. 5W.
EFX.
RETURN
EFFECTS OUT
O O
Amplifier
|
| То low frequency enclosures
To high frequency enclosures
Select the crossover point which matches the require-
ments of your speaker/horn system. Keep High Pass and
Low Pass consistent through the power amplifiers and to
the speakers. Balance the High/Low response using the
level controls on the power amplifiers.
*Use HIGH (PAD & E.Q.) out when the high frequency
component uses a Peavey Model 22A" driver.
MASTER PATCH PANEL
MS™ MIXER SPECIFICATIONS
All specifications are typical unless otherwise noted.
0 dBY = 1 Volt O dBY = .778 Volt
All specifications are referenced to nominal output level (0
dBY) unless otherwise noted,
All measurements are wideband 20 Hz to 20 kHz unless other-
wise noted.
CHANNEL
EQUIVALENT INPUT NOISE:
(150 Ohm 25° C Theoretical -133 dBV)
(Mic Input to Channel Pre Send)
-133 dBV (150 Ohm, 25°C, 60 dB Gain)
SHORT CIRCUIT INPUT NOISE:
(0 Ohm 25°C)
(Mic Input to Channel Pre Send)
-140 dBV (D Ohm, 25°C, 60 dB Gain)
FREQUENCY RESPONSE:
+ 2 dB 20-20,000 Hz all EQ flat
DISTORTION:
Less than .05% at 0 dB Output at 60 dB Gain Typical .003% at 0
dB Output at 30 dB Gain
(Mic Input to L or R Outputs, EQ flat, Sliders at 0)
COMMON MODE REJECTION RATIO (CMRR):
Greater than 100 dB
(Typically 120 dB)
INPUT IMPEDANCE:
Mic = BK Ohms
Line = 40K Ohms
Return = 20K Ohms
OUTPUT IMPEDANCE:
Send = 100 Ohms
HIGH EQ:
+15 dB at 10 kHz minimum Center
Detent flat + 2 dB
MID EQ:
+ 15 dB at selected frequency
Center Detent flat + 2 dB
MID FREQUENCY:
200 Hz to 4 kHz adjustment of Mid Frequency
LOW EQ:
+15 dB at 50 Hz minimum
Center Detent flat + 2 dB
MAXIMUM PREAMP GAIN:
60 dB minimum
MINIMUM PREAMP GAIN:
2 dB typical
MAXIMUM CHANNEL GAIN:
(Pan at L or R, Slide at Max, EQ flat)
74 dB
MAXIMUM INPUT LEVEL:
Mic = +16 dBV (6.3V RMS)
Line = +36 dBV (60V RMS)
Return = +18 dBV (8V RMS)
MAXIMUM OUTPUT LEVEL:
Send = +18 dBV (8V RMS)
NOMINAL INPUT LEVEL:
Mic = -18 dBm (100 mV, -20 dBV)
Return = 0 dBY (1.0v RMS)
HEADROOM:
Nominal = 18 dB
Red LED = 8 de
PAN CHARACTERISTICS:
2 dB down at Mid Position
LED LEVEL:
Green = -10 dBY (.32Y RMS)
Red = +10 dBV (3.2V RMS)
MASTER
LED METER CALIBRATION:
0 = 0 dBV (1.0V RMS)
NOMINAL OUTPUT LEVEL:
Master = +0 dBV (1.0V RMS)
L & R = +0 dBV (1.0V RMS)
Monitor À & B = +0 dBV (1.0V RMS)
Effects A & B: High = 0 dBY (1.0V RMS)
Low = -12 dBY (.25V RMS)
NOMINAL HEADROOM:
Master = 19 dB
LáR=19d8e
Monitor À & B = 19 dB
Effects À & B 19 dB
MAXIMUM OUTPUT LEVEL:
Master = + 19.5 dBV (9.5V RMS, +21.5 dBv)
LáR=+195 dev (9.5V RMS, +21.5 dBv)
Monitor A & B = 19.9 dBV (9.5V RMS, +21.5 dBv)
Effects A & B:High = 18 dBV (9.0V RMS, + 20 dBv)
Low = 6 dBV (2.0V RMS, + 8 dBv)
OUTPUT IMPEDANCE:
Master = 100 Ohms
L & R= 100 Ohms
Monitor A & B = 100 Ohms
Effects A & B: High = 1000 Ohms
Low = 250 Ohms
OUTPUT NOISE:
MS-12
Residual:-99 dBV
(L & R sliders down)
Bus:-82 dBV
(All channel sliders down, Effects Returns down, all Pan at
middle)
Nominal:-78 dBV
(All channels at 30 dB Gain, 150 Ohm input, EQ flat, Pan mid-
dle, sliders at 0, assigns at L 6 R, Effects Returns down)
MS-16
Residual:-99 dBV
(L & R sliders down)
Bus:-80.5 dBV
(All channel sliders down, Effects Returns down, all Pan at
middle)
Nominal:-76 dBV
(All channels at 30 dB Gain, 150 Ohm input, EQ flat, Pan mid-
dle, sliders at 0, assigns at L & R, Effects Returns down)
EFFECTS A & B RETURN INPUT IMPEDANCE:
80K Ohms
EFFECTS À & B RETURN GAIN:
16 d8 Max
PFL AUX:
Tip = PFL Signal at 1V RMS Nom
Ring = PFL Switch Signal (Grounding activates PFL)
HEADPHONE:
Stereo 8 Ohm to 200 Ohm nominal
Tip = Left, Ring = Right, Sleve = Ground
500 mW total power
Less than 1% distortion
GRAPHIC EQUALIZERS
(All sliders flat, 1.0¥ RMS unless noted)
FILTER BANDWIDTH:
1 Octave
FILTER FREQUENCIES:
63, 125, 250, 500, 1K, 2K, 4K, 8K, 16 kHz (150 Stds.)
FILTER Q:
1.57
MAXIMUM BOOST & CUT:
+12 dB
DISTORTION (THD):
05% Maximum
FREQUENCY RESPONSE:
5 Hz to 40 kHz + 1 dB
INPUT LEVEL:
Nom = 0 dBV (1.0V RMS)
Max = 19 dBY (9V RMS)
OUTPUT LEVEL:
Nom = 0 dBV (1.0V RMS)
Max = 19 dBV (9V RMS)
INPUT IMPEDANCE:
20K Ohms
QUTPUT IMPEDANCE:
100 Ohms
RIAA PREAMP
INPUT IMPEDANCE:
47K Ohms
NOMINAL INPUT:
12 mV RMS at 1 kHz
ELECTRONIC CROSSOVER
CROSSOVER FREQUENCY:
500 Hz, 800 Hz, or 1200 Hz (Switch-Selectable)
FILTER SLOPE:
18 dB per Octave
FILTER TYPE:
High & Low = Butterworth
High {Pad and EQ) EQ = Modified Butterworth
(Mid Frequency Pad with High Frequency EQ)
INPUT IMPEDANCE:
5K Ohms
QUTPUT IMPEDANCE:
Low = 100 Ohms
High = 100 Ohms
High EQ = 1K Ohm
INPUT LEVEL:
Nom = 0 dBV (1.0V RMS)
Max = +18 dBV (8V RMS)
QUTPUT LEVEL (HIGH & LOW):
Мот = 0 dBV (1.0V RMS)
Max = +18 dBV (8V RMS)
OUTPUT LEVEL (HIGH (PAD AND EQ)):
Nom = -6 dBV at 1 kHz
= -1,5 dBY at 10 kHz
Max = +12 dBV at 1 kHz (4V RMS)
= +16.5 dBV at 10 kHz (6.6V RMS)
ELECTRONIC DELAY
DELAY TIME:
Max = 185 ms.
Min = 13 ms.
DISTORTION (0 dBV):
Less than 1%
QUTPUT NOISE (INPUT SHORTED):
-104 dav
FREQUENCY RESPONSE:
20 -20,000 Hz Max
High Frequency limit depends upon delay time
INPUT LEVEL:
Nom= 0 dBV (1.0¥ RMS)
Max = +6 dBV (2.0V RMS)
OUTPUT LEVEL:
Nom = 0 dBY (1.0V AMS)
Max = + 6 dBV (2.0VRMS)
INPUT IMPEDANCE:
33K Ohms
OUTPUT IMPEDANCE:
100 Ohms
POWER CONSUMPTION
М5 = 120 VAC 60 Hz, 90 Watts Max.
— RIGHT — LEFT = — AUXILIARY INPUT; =— — — = CH. 15 & 16
STEREO CUT LINE IN MASTER LEFT MON, A EFE. A SOURCE SEND RETURN
—— CROSSOVER —— NORMAL J
(O) ©| © PHONG am
O) = RIGHT MON. E EFE. B
HIGH HIGH MASTER = DELAY REY. —
(PAD A EC B MON. A
A O ®) | > À LOWZIN
GRAPHIC OUT PATCH FT. SW.
GRAPHIC OUT EFX.
= © © O «©
INPUT
ВАР
MASTER A e GRAPHIC IM RETURN 18 © LINEN
BALANCED LINE OUT LIME IN BALANCED LINE OUT
MASTER QUT H OUT L MON. CUT EFFECTS OUT PHONG
INPUT
| MASTER PATCH PANEL e)
DURATION PER DAY IM HOURS
ACCORD EXPOSURE
EAR PL M THE EAR
EXPO
PERS ARE
LIT
THIS O GONSOLESPREAMP
Gal [RLIZATION CONTROLS A
LOL TE ETEMD
МАХ ESTAN
17156 Ou
ES CR
co
TAR
aa TAPE NO
I. Read all safely ard operatic insloclang Deloria png 1hig
predaci
. All setaly end operating instruchóne 3Rqguid be retainad lor
litre reference
One а М сана in He cosrabng inylractions ard an the
back ol the ur
All aparating matruelons should be loliowed
Thig product angulo rad Be used meer weber, i.e a botte
SINE, Seummimg poagl, él Casemerl, 8c
This product should be located 26 IAB IES position des nal
име Рена with «is proses ventilation. IF should motas placed
Lgl agains & well ar placed ré à Built-in erélogure hel wall
impago The Fow ol cooling as
This product should not ba placed mia á sounce of heat such
as A ÉNP6, Feater, radigror or ancihar heal producimo
amplifier
Fur
o
vu E
a
a
4
7 DANGER
EXPOSURE TO EXTREMELY HIGH NOISE LEVELS MAY CAUSE à PERMANENT HEARING LOSS INDIVIDUALS VARY CO Fe EEE ВСТО SLUSCEPTIGILITÉ TO NOISE INOUCEO HE AFIAG LOSS. BUT
NÉAALE EVERYONE WILL LOSE SOME REARING IF EXPOSED TD SUFFICIENTLY INTENSE MOISE FOR À SUFFICIENT TIM
THE LS. GOVERNMENT 'S OCCUPATIONHAL SAFETY AND HEALTH ADMINESTRATION (C5Hä] HAS SPECIFIED TRE FO Come PERMISSIBLE WOISE LEVEL EXPOSURES:
MOVED. W GLY RE END TH PAINTED SURFACES MOR ANY OTHER ты FECHA SUCH APPLICATIONS
MEDIUM OF LIGHT ADHESIVE MASKING on MUTER LABEL TAPE i RECOMMENDED IF TAPE 15 USED ANY TAPE LEFT ON PAINTED SURFAGE FOR EXTENDED PERIODS WILL BE DIFFICULT TO
REMOVE. HEVER USE CLEAR OB SCOTCH TAPE FOR THESE APPLICATIONS
SOUND LEYEL dá. SLOW RESPONSE
HER T AFE THA Y CESTA
Connect only 10 a porerer supply Me hyoe marked ash umi
adjacent fo bhe power supaly coro
Mever ила К off Ihe Ground pin ch lhe power supply cord. For
More nlarmation on grounding write lar our res bookie
Shack Hazard and Grovading
Power supply Socds should always be handled carefully
Meyer walk or place equigment cn power duppiy Conds
Farigdically cnesk corde tor eutt óramgos pl siress, especially
ат Ва [óug Sd Lhe ocinl where Ine cord ariba the ка
Tre power supply cord should be unpliagged wham The pals
La nu Pos larg pandas Of Gime
Metal parts car ba gleaned wih a damp rag. The vinyl
Cémériaÿ vééd on soma units car ba cleangd waln a dhmp rag,
or 31 ammon cds Base Paeidahole sagas if Ascagsary
5
Care shguld ge takes 20 ЗВ но в di nat fall and hqueds dre
rat spilled nla fe uml гомо the ventilahon hoes or any
Сна Den
Thos uri shoud be checked by & qualhed serace bechrecian
The power supply cord or plug has been damaged
Anything has ‘allier or Bean spilled isa ne unl
The url does nor áperata correct
I'he uml has bern dropped or the anclosare damaged
The user saoguld of attempt ho saraoe Ths Ego pment Al
Seva wDrE sfóLd0 be dore by a quahfied sensee techmie un
Fame =
THIS LIMITED WARRANTY VALID ONLY WHEN PURCHASED AND REGISTERED IN THE UNITED STATES OR CANADA. ALL EXPORTED PRODUCTS ARE SUBJECT TO
WARRANTY AND SERVICES TO BE SPECIFIED AND PROVIDED BY THE AUTHORIZED DISTRIBUTOR FOR EACH COUNTRY.
Ces clauses de garantie ne son! vaiables qu'aux Etats-Unis et au Canada. Dans lous les autres pays, les clauses de garantle et de maintenance sont lixees par le distributeur national et
assuree par lul selon la legislation en vigueur.
Diese Garantie ist nur in den USA and Kanada gultig. Alle Export-Produkte sind der Garantie und dem Service des Importeurs des jewelllgen Landes unterworfen.
Esta garantia es valida solamente cuando el producto es comprado en E.U. continentales o en Canada. Todos los productos que sean comprados en el extranjero, estan sujetos a las
garantias y servicio que cada distribuidor autorizado determine y ofrezca en los dilerentes paises.
ONE-YEAR LIMITED WARRANTY/REMEDY
PEAVEY ELECTRONICS CORPORATION ("PEAVEY") warrants this product, EXCEPT for covers, footswitches, patchcords, tubes and meters, to be free from defects in material
and workmanship for a period of one (1) year from date of purchase, PROVIDED, however that this limited warranty is extended only to the original retail purchaser and is subject ta the
conditions, exclusions and limitations hereinafter set forth:
PEAVEY 90-DAY LIMITED WARRANTY ON TUBES AND METERS
If this product contains tubes or meters, Peavey warrants the tubes or meters contained in the product to be free from defects in material and workmanship for a period of ninety (90)
days from date of purchase; PROVIDED, however, that this limited warranty is extended only to the original retail purchaser and is also subject to the conditions, exclusions and
limitations hereinafter set forth.
CONDITIONS, EXCLUSIONS AND LIMITATIONS OF LIMITED WARRANTIES
These limited warranties shall be void and of no effect if:
a. The first purchase of the product is for the purpose of resale; or
b. The original retail purchase is not made from an AUTHORIZED PEAVEY DEALER: or
c. The product has been damaged by accident or unreasonable use, neglect, improper service or maintenance, or other causes not arising out of defects in material or
workmanship; or
d. The serial number affixed to the product is altered, defaced or removed,
In the event of a defect in material and/or workmanship covered by this limited warranty, Peavey will;
a. In the case of tubes or meters, replace the defective component without charge:
b. In other covered cases (i.e., cases involving anything other than covers, footswitches, patchcords, tubes or meters), repair the defect in material or workmanship or replace
the product, at Peavey's option; |
and provided, however, that, in any case, all costs of shipping, if necessary, are paid by you, the purchaser.
THE WARRANTY REGISTRATION CARD SHOULD BEACCURATELY COMPLETED AND MAILED TO AND RECEIVED BY PEAVEY WITHIN FOURTEEN ( 14) DAYS FROM THE
DATE OF YOUR PURCHASE.
In order to obtain service under these warranties, you must:
a. Bring the defective item to any AUTHORIZED PEAVEY DEALER or AUTHORIZED PEAVEY SERVICE CENTER and present therewith the ORIGINAL PROOF OF
PURCHASE supplied to you by the AUTHORIZED PEAVEY DEALER in connection with your purchase from him of this product.
If the DEALER or SERVICE CENTER is unable to provide the necessary warranty service you will be directed to the nearest other PEAVEY AUTHORIZED DEALER or
AUTHORIZED PEAVEY SERVICE CENTER which can provide such service.
OR
b. Ship the defective item, prepaid, to:
PEAVEY ELECTRONICS CORPORATION
International Service Center
Highway 80 East
MERIDIAN, MS 39301
including therewith a complete, detailed description of the problem, together with a legible copy of the original PROOF OF PURCHASE and a complete return address. Upon
Peavey's receipt of these items:
If the defect is remedial under these limited warranties and the other terms and conditions expressed herein have been complied with, Peavey will provide the necessary
warranty service to repair or replace the product and will return it, FREIGHT COLLECT, to you, the purchaser.
Peavey's liability to the purchaser for damages from any cause whatsoever and regardless of the form of action, including negligence, is limited to the actual damages up to the
greater of $500.00 or an amount equal to the purchase price of the product that caused the damage or that is the subject of or is directly related to the cause of action. Such purchase
price will be that in effect for the specific product when the cause of action arose. This limitation of lia bility will not apply to claims for personal injury or damage to real property or
tangible personal property allegedly caused by Peavey's negligence. Peavey does not assume liability for personal injury or property damage arising out of or caused by a non-Peavey
alteration or attachment, nor does Peavey assume any responsibility for damage to interconnected non-Peavey equipment that may result from the normal functioning and
maintenance of the Peavey equipment.
UNDER NO CIRCUMSTANCES WILL PEAVEY BE LIABLE FOR ANY LOST PROFITS, LOST SAVINGS, ANY INCIDENTAL DAMAGES OR ANY CONSEQUENTIAL DAMAGES
ARISING QUT OF THE USE OR INABILITY TO USE THE PRODUCT, EVEN IF PEAVEY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
THESE LIMITED WARRANTIES ARE IN LIEU OF ANY AND ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR USE; PROVIDED, HOWEVER, THAT IF THE OTHER TERMS AND CONDITIONS NECESSARY TO THE EXISTENCE OF
THE EXPRESS, LIMITED WARRANTIES, AS HEREINABOVE STATED, HAVE BEEN COMPLIED WITH, IMPLIED WARRANTIES ARE NOT DISCLAIMED DURING THE
APPLICABLE ONE-YEAR OR NINETY-DAY PERIOD FROM DATE OF PURCHASE OF THIS PRODUCT.
SOME STATES DONOTALLOWLIMITATION ONHOWLONG AN IMPLIED WARRANTY LASTS, OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THESE LIMITED WARRANTIES GIVE YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY
ALSO HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE,
THESE LIMITED WARRANTIES ARE THE ONLY EXPRESS WARRANTIES ON THIS PRODUCT, AND NO OTHER STATEMENT, REPRESENTATION, WARRANTY OR
AGREEMENT BY ANY PERSON SHALL BE VALID OR BINDING UPON PEAVEY.
Inthe event of any modification or disclaimer of express or implied warranties, or any limitation of remedies, contained herein conflicts with applicable law, then such modification,
disclaimer or limitation, as the case may be, shall be deemed to be modified to the extent necessary to comply with such law.
Your remedies for breach of these warranties are limited to those remedies provided herein and Peavey Electronics Corporation gives this limited warranty only with respect to
equipment purchased in the United States of America.
INSTRUCTIONS — WARRANTY REGISTRATION CARD
1. Mail the completed WARRANTY REGISTRATION CARD to:
PEAVEY ELECTRONICS CORPORATION
POST OFFICE BOX 2898
MERIDIAN, MISSISSIPPI 39302-2898
a. Keep the PROOF OF PURCHASE. In the event warranty service is required during the warranty period, you will need this document. There will be no identification card
issued by Peavey Electronics Corporation.
2. IMPORTANCE OF WARRANTY REGISTRATION CARDS AND NOTIFICATION OF CHANGES OF ADDRESS:
a. Completion and mailing of WARRANTY REGISTRATION CARDS — Should notification become necessary for any condition that may require correction, the REGISTRATION
CARD will help ensure that you are contacted and properly notified.
b. Notice of address changes — If you move from the address shown on the WARRANTY REGISTRATION CARD, you should notify Peavey of the change of address so as to
facilitate your receipt of any bulletins or other forms of notification which may become necessary in connection with any condition that may require dissemination of
information or correction.
3. You may contact Peavey directly by telephoning (601) 483-5365.
4. Please have the Peavey product name and serial number available when comm unicating with Peavey Customer Service.
Features and specifications are subject to change without notice.
PEAVEY ELECTRONICS CORPORATION 711 A Street/Meridian, MS 39302-2898/U.S.A./(601) 483-5365/Telex: 5041 15/Fax: 484-4278
©1989 #80300550 Printed in U.S.A.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021