Owner`s Manual
INSTALLATION AND
OPERATION INSTRUCTIONS FOR
WALL- MOUNT AND BUILT- IN UNITS
BI-50-FLUSHMT-BLKGLS BI-50-FLUSHMT-WHTGLS
BI-50-FI-FLUSHMT-BLKGLS
operation
09 13-01
TABLE OF CONTENTS
CONGRATULATIONS!
In selecting this Amantii Wall Mount OR Built-in electric fireplace, you have chosen the
finest and most dependable fireplace on the market today. A beautiful and functional
addition to the finest homes. Welcome to the family of satisfied Amantii electric fireplace
owners.
Please read and carefully follow all of the instruction sfound in this manual. Please pay
special attention to the safety instructions provided in this manual. The instructions
included here will as sure that you have many years of dependable and enjoyable service
from your Amantii product.
Important instructions
Page 3
BI-50-FLUSHMT-BLKGLS/WHTGLS (BI-FI-50FLUSHMT-BLKGLS)
Page 4
Installation Overview
Page 5
Package Contents
Page 6
Built-In Installation
Page 7
Wall Mount Installation
Page 9
Media options
Page 10
Fire Glass Media Installation
Page 11
Front Installation
Page 12
Operating the Unit
Page 13
Replacing The Remote Control Battery
Page 17
Care And Maintenance
Page 18
Fireplace Maintenance
Page 19
Trouble Shooting
Page 20
Parts list
Page 21
Service History
Page 22
Warranty
Page 23
Dealer Contact Information
Back Page
2
IMPORTANT INSTRUCTIONS
WARNING!
5. Do not use outdoors.
15.
properly grounded outlet box. The adapter should not be used if a three-slot grounded receptacle is available.
Cover Of Grounded
Outlet Box
Metal
Screws
Grounding Pin
A B
Adapter
C D
Grounding
Means
Grounding
Pin
Fig. 1
SAVE THESE INSTRUCTIONS
3
BI-50-FLUSHMT-BLKGLS/WHTGLS
BI-FI-50-FLUSHMT-BLKGLS
Built-In or Wall Mount Appliance
Voltage
120V AC,60Hz
Amps
12A
appliances in the United States and Canada. If you need assistance during installa-
1500W
HEATER
HIGH
1500W
LOW
750W
This appliance has been tested in accordance with the UL Standand 2021 for
NO HEATER
25W
MOTOR HEATER
19W
MOTOR FLAME
Appliance Width
4W
47 1/2” or 120.6 cm
Appliance Height
21 1/8” or 53.6 cm
Appliance Depth
6 1/8” or 15.5 cm
Gross Weight
80lbs or 36.35kg
NOTE: This appliance must be electrically
wired and grounded in accordance with
local codes. In the absence oflocal codes,
us the current CSA C22.1 Canadian Electrical Code in Canada or the ANSI/NFPA
States.
Left side
74.81” or 190.00 cm
45 1/2
6 3/4
51
47 1/2
4
1/2
21 1/8
10
23
Cord Length
INSTALLATION OVERVIEW
NOTE: BEFORE YOU INSTALL
SITE SELECTION
wall.
Review and consider all of the following condir
r
re etc.
wo (2) wall
dir
ing.
ethods:
-
overhead light-
et for ease of electric
and all hardware fr
ox and r ove all
aterials prior to installapackaging relat
Power supply Wire Gage
Voltage
Wire Gage
Fuse
14 G .
ht and away fr
electric
t-In (page 7)
W
nt (Page 9)
120 v
rapes, pillow
15 MP
Wall switch / t hermostat Wire Gage
Voltage
Wire Gage
5 Volts
18 Gage
Volt cir
referr
cated cir
r
red.
-
PACKAGING LIST
with:
WARNING:
r
re the power cord is not installed
i
so
pinched
or
against
a
sharp
edge
that it is
and ensure that the power cord is stored
or
red to avoid tripping or snagging
Decorative media (See page 11)
TOOLS & BUILDING SUPPLIES
NORMALLY REQUIRED
ry to persons.
st c
with local
te control
T
Phillip
codes
-
aw and/
Level
ry to persons.
To reduce the risk of fire, do not store or
use gasoline or other flammable vapors
and liquids in the vicinity of the heater.
Pliers
re
Gloves
5
rewdriver
aw
Tape
E
Fr
aterials
Wall Finishing Marterials
aterials
stable)
PACKAGE CONTENTS
B
C
A
E
D
Part
A
B
C
D
E
Glass
1
1
1
1
1
Wall Mount Bracket
Decorative Media
CONTENTS
Part
Description
Quantity
A
Screw
0.16 in. x 1.0 in.
10
B
Wall Plug
0.3 in. x 1.5 in.
10
C
Wood Screw
0.16 in. x 0.6 in.
10
Picture
6
NEW CONSTRUCTION OR RENOVATION
CAUTION: Two people may be needed to
NOTE BEFORE YOU INSTALL
moisture and is located at least 0.91 m or
als such as curtains or drapes, furniture,
bedding, paper, etc.
WALL
min. 5 cm
2 in
BI-50-FLUSHMT units must stick out
of the wall a minimum of 1/2" or 1.3 cm.
min. 5 cm
2 in
Clearance to combustibles
Clearances are measured from the unit
not the glass.
FLOOR
Sides ---------------------- 2 in / 5 cm
Floor ---------------------- 1 in / 2.5 cm
Top ---------------------- 2 in / 5 cm
Back ---------------------- 1/4 in / 0.6 cm
min. 2.5 cm
1 in
2. Place the appliance in selected loca-
and store appliance in a safe, dry and
4. Prepare a wall with a framed opening to accomodate the size of your unit.
For the BI-FLUSHMT the rough wall opening
is 49"W × 6 3/8" × 22"H
Any new wiring must be done in compliance
with local and national codes and other applicable regulations.
WARNING:
To prevent contact with sagging or
ance must not be installed against
WARNING:
outlets or circuits. To reduce the risk
licensed electrician.
result.
7
BI-50-FLUSHMT INSTALLATION BUILT IN
NOTE BEFORE YOU INSTALL
k
BI-50-FLUSHMT units must stick out
of the wall a minimum of 1/2" or 1.3 cm.
The rough wall opening size of the fireplace.
W(")
49
D(")
6 3/8
H(")
22
w
ow
4. Drive mounting screws through the holes
located on the top and both sides of the
unit into the wall studs.
H
BI-50-FLUSHMT
r
W
D
1" [13mm]
2
Wall
8
NOTE: BEFORE YOU INSTALL
Stakes for hanging
wall bracket
It is strongly recommended that the screws be
screwed into the wall studs where possible. If
anchors are used.
ke sure it is level.
5 inch
hanging into the keyholes on the back of the unit.
Floor
3. Check the appliance for stability ensuring that
the appliance will not pull free from the wall.
4. Drive mounting screws into the mounting bracket on
the bottom of unit.
Stakes for hanging
Wall
Back of unit
Side view
9
Media op ons
Model BI-50-FLUSHMT-BLKGLS is shipped with an LED ember log that is pre-installed.
3 colours of fire glass media are also included.
See page 16 for log removal instruc ons.
See page 16 for media installa on instruc ons.
Clear
Harvest Moon
LED log
Sun Tea
Models
BI-50-FLUSHMT-WHTGLS, BI-FI-50-FLUSHMT-BLKGLS
are shipped with 3 large glass nuggets, clear and blue
diamond shaped media.
Glass nuggets, clear and
blue diamond shaped media
See page 16 for media installa on instruc ons.
10
Fire Glass Media - Log Installa on
1. Removing the log
Unplug the unit from wall and make sure controls are switched off. The LED log is shipped in place. The log has
tabs on each side that hold it secure. Remove the side panel to remove the log set and the LED strip.
2 . Installing the fire glass media
Pour the fire glass media into the tray as shown below. Fee free to use any combina on of fire glass media that
you find most appealing.
11
FRONT INSTALLATION
NOTE: BEFORE YOU INSTALL
It is recommended that two people install the
front onto the appliance, wear safety glasses and
gloves when handling glass.
1.Lift fireplace front and line up the brackets
with the four (4) shoulder screws on the side of
appliance body
NOTE: Before you lift the front glass. Unscrew
two screws on both side of the fireplace as
below shown.
Mount
Unit
Shoulder Screw
Wall
Unit
Shoulder Screw
Wall
Screw
12
OPERATING THE UNIT
Wall
1. Make sure the appliance is switched OFF (refer
19
on the right hand side of the unit.
3. Plug unit into electrical outlet.
HARD-WIRE INSTALLATION
If it is necessary to hard wire this appliance, a qualified
electrician may remove the cord connection, and wire the
appliance directly to the house hold wiring.
1. Unscrew two screw show in the below. Remove the cover
plate and the power cord fix piece, remove power cord.
Remove the knockout.
2. Attach the wiring to the junction block
3. Put the plate back and screw back.
Power adaptor port
WARNING:
outlets or circuits. To reduce the risk of
licensed electrician.
Appliance has overheated and safety
device has cause the thermal switch to
discount. Unplug the appliance, allow
appliance to cool for 15 minutes, then
plug back in.
Fix plate
Inspect for an objects on or adjacent to
the heater that may have locked the
airflow or otherwise caused high
temperatures to have occurred.
13
OPERATING THE UNIT
This remote control will be used on : BI-FI-50-FLUSHMT-BLKGLS, BI-50-FLUSHMT-WHTGLS
The button located at the top position of the remote control is ON/OFF. Press it, the flame and
ember will be on. The heater will be off. Press again, the fireplace will turn off.
“DISPLAY ON/OFF”: Switching the fireplace flame and tray light ON/OFF. It has functions of setting
memory.
“DISPLAY ORANGE ”: Adjust the orange colour brightness of flame.
“DISPLAY BLUE ”: Adjust the blue colour brightness of flame.
“HEATER ON/OFF”: Switching the fireplace heater ON/OFF. It
has functions of setting memory.
DISPLAY ON/OFF
ORANGE
BLUE
DISPLAY
“HIGH”: The heater works at 1500W.
“LOW”: The heater works at 750W.
“TEMP.”: The heater keep working if the room temperature lower
than 22℃. The heater not working if the room temperature
higher than 25℃.
14
HEATER ON/OFF
HIGH
LOW
TEMP.
This remote control will be used on : BI-50-FLUSHMT-BLKGLS
The button located at the top position of the remote control is ON/OFF. Press it, the flame and
ember will be on. The heater will be off. Press again, the fireplace will turn off.
“DISPLAY ON/OFF”: Switching the fireplace flame and tray light ON/OFF. It has functions of setting
memory.
“FLAME ORANGE”: Adjust the orange colour brightness of flame.
“FLAME YELLOW”: Adjust the yellow colour brightness of flame.
“TRAY ORANGE”: Adjust the orange colour brightness of tray.
“ TRAY WHITE”: Adjust the white colour brightness of tray.
“HEATER ON/OFF”: Switching the fireplace heater ON/OFF. It
has functions of setting memory.
“HIGH”: The heater works at 1500W.
“LOW”: The heater works at 750W.
“TEMP.”: The heater keep working if the room temperature lower
than 22℃. The heater not working if the room temperature
higher than 25℃.
15
1. Power ON/OFF switch
2. Heat control button
3. Flame control button
4. HEATER LED
5. POWER LED
Plug the heater into a suitable outlet.
1) “Power ON/OFF”
Set this switch to position I to turn the product ON. Setting it to O to turn the product OFF.
POWER LED will be lit when the fireplace insert is on.
The
2) “Heat control button”
Press the HEAT button repeatedly to set the heater to the desired heat setting. The HEATER LED will
indicate the current setting for the heater as shown below:
HEATER LED = Red = 1500W HEAT OUTPUT
HEATER LED = Blue = 750W HEAT OUTPUT
HEATER LED = Purple = AUTO MODE
HIGH / 1500W
LOW / 750W
AUTO MODE
HEATER INDICATOR
HEATER INDICATOR
HEATER INDICATOR
OFF
Auto Mode
In this mode the heater will automatically turn on and off. When the room temperature drops below
71° F. (22° C) the heater will turn on to the high heat setting (1500 watt). When the room temperature
is between 71° and 77° F (22-25° C) the heater output will switch to low heat setting (750W). When
the room temperature goes above 77° F (25° C) the heater will turn off.
3) “Flame control button”
Press the Flame brightness adjustment button to adjust the flame height and ember bed brightness.
Press the FLAME control button to cycle through LO, MED, HI and OFF.
16
REPLACING THE REMOTE CONTROL BATTERY
When the remote control stops operating or its range seems reduced, it is time to replace the batteries
with new ones. Remove the batteries if the remote control won’t be used for a long period of time.
1. The battery compartment is located on the back end of the remote.
2. Press the small tab inward as you slide the battery door open and remove the old batteries.
3. Replace with (2) AAA batteries (not included), making sure the + and - sides of the battery match the
inside of the battery compartment.
4. Replace the battery door.
CAUTION:
Always purchase the correct size and grade of battery most suitable for the intended use.
y.
Note:
Caution for Ingestion.
DISPOSAL OF USED BATTERIES
Batteries may contain hazardous substances which could be endangering to the
enviroment and to human health.
This symbol marked on the battery and/or packaging indicates that used battery shall
not be treated as municipal waste. Instead it shall be left at the appropriate collection
point for recycling.
By ensuring used batteries are disposed of correctly, you will help to prevent potential
The recycling of
materials will help to conserve natural resources.
For more information about collection and recycling of used batteries, please contact
your local municipality or your waste disposal service.
Note: please operate remote transmitter at a slow measured pace. Press the remote control buttons with
an even motion and gentle pressure. Repeatedly pressing buttons in rapid succession may cause the
transmitter to Malfunction.
17
CARE AND MAINTENANCE
CLEARANCE TO COMBUSTIBLES
Keep electrical cords, drapery, furniture and other combustibles at least 3 ft. from the front of the heater
and away from the sides.
CLEANING TRIM
Clean the metal trim using a soft cloth, slightly dampened with a citrus oil-based product and buff with a
clean soft cloth. Do not use brass polish or household cleaners as these products will damage the metal
trim. Citrus oil-based products can be obtained at supermarkets or hardware stores.
WARNING: Make sure the power is turned off before proceeding. Any electrical repairs
or rewiring of this unit should be carried out by a licensed electrician in accordance with
national and local codes.
If repairing or replacing any electrical component or wiring, the original wire routing,
color coding and securing locations must be followed.
WARNING: Electrical outlet wiring must comply with local building codes and other
WARNING:
. Immediately
electrical system.
WARNING: Disconnect power before attempting any maintenance or cleaning to reduce
WARNING: During any service of this appliance, the power to the unit must be turned off.
First turn the main power switch to the OFF position. Then remove the electrical plug from
the wall outlet.
18
FIREPLACE MAINTENANCE
WARNING:
Disconnect power before performing any maintenance or cleaning to reduce the risk of
LED LIGHT BULB REPLACEMENT
LED light bulbs are to be replaced by the manufacturer, it’s service agent or similar quali-
WARNING:
UNIT DISPOSAL
Do not dispose with other household wastes. To prevent possible harm to the environment
or human health from uncontrolled waste disposal, recycle it responsibly to promote the
19
TROUBLE SHOOTING
WARNING
Disconnect power before performing any maintenance and allow to cool before servic-
SYMPTOM
POSSIBLE CAUSES
Fireplace doesn’t work.
Fireplace inner temperature over
heatng or home circuit breaker
has opened.
or log set and ember is not
glowing.
LED Light(s) burt out or wiring is
loose.
Remote Control does not
work.
CORRECTIVE ACTION
Reset switch by turning main power switch off and waiting five
mimutes, then turning it back on.
if necessary. Inspect light bulbs and replace if necessary.
Replace AA batteries in remote control. If problem persists,
there may have been a loss of power to the unit as a possible result from a power failure
(i.E. Breaker tripped).
Circuit Breaker trips or fuse
blows when the unit is on.
to ensure it is on a dedicated circuit with proper amp. rator replace wiring and/or connectors as necessary.
Heater does not provide heat Thermal switch has been trippped. Turn the unit off and unplug the unit for five minutes.
when turned on
Circuit breaker has been tripped
Plug back in and turn the unit on. If plug can be reached,
follow directions for tripped circuit breaker. Turn off circuit
breaker that supplies electricity to the unit. Wait five minutes
then flip circuit breaker back on.
not turn on.
Appliance will not come on
ON.
a. Appliance has overheated and
mal switch to disconnect.
OR
b. House circuit breaker has
tripped.
a. Unplug the appliance, allow appliance to cool for 15 minutes, then plug back in.
a. Appliance is not plugged into
an eletrical outlet.
OR
b. Appliance has overheated and
mal switch to disconnect.
a. Check plug and plug it in.
b. Reset the house circuit breaker
b. Unplug the appliance, allow appliance to cool for 15 minutes, then plug back in.
20
PART LIST
REF NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
PART NO.
602030C
601089C
601089E
301506
601120H
601121N
601122H
601123N
601120J
601121G
601140
601141
10105031
10105048
10101200B
10104010
10305513
10701163
10701163B
10701163C
395502
395012
DESCRIPTION
BLOWER AND HEATER ASSEMBLY
CIRCUIT BOARD
CIRCUIT BOARD
REMOTE RECEIVER
LED STRIP FOR FLAME
LED STRIP FOR FLAME
LED STRIP FOR LOG
LED STRIP FOR LOG
LED STRIP FOR EMBER
LED STRIP FOR EMBER
LED STRIP FOR FLAME
LED STRIP FOR LOG
REMOTE
REMOTE
FLAME MOTOR
SWITCH
LOG
FRONT TEA GLASS
FRONT CLEAR GLASS WITH WHITE PAINT
FRONT CLEAR GLASS WITH BLACK PAINT
Flicker assembly
Back cloth
21
SERVICE HISTORY
This heater must be serviced annually depending on usage.
Date
Dealer
Name
service technician
Name
service Performed
NOTES:
22
special Concerns
WARRANTY
Amantii Imports Corp. (”Amantii”) warrants that your newly purchased Amantii electric fireplace is free from manufacturing and
material defects for a period of one (1) year from the date of the first purchase, subject to the conditions and limitations contained
below.
Warranty Application & Exclusions
This limited warranty applies to your newly purchased Amantii electric fireplace; the limited warranty’s application is limited to purchases made in any province of Canada or in any of the 52 States of the United States of America, including the District of Columbia.
Only the original purchaser of the product is eligible for coverage under this limited warranty; the warranty is not transferable.
Products excluded from this limited warranty
Light bulbs are not covered by this limited warranty and are the sole responsibility of the owner/purchaser.
Warranty Coverage and Team
Products covered by this limited warranty have been tested and inspected prior to shipment and, subject to the provisions of this warranty, Amantii warrants such products to be free from defects in material and workmanship for a period of one (1) year from the date
of the first purchase of such products.
The limited one (1) year warranty period for products also applies to any implied warranties that may exist under applicable law. Some
jurisdictions do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to the purchaser.
All other warranties - expressed or implied - with respect to the product, its components and accessories or any obligation/liabilities
on the part of Amantii are hereby expressly excluded.
Limitations to Coverage Under Limited Warranty
This limited warranty does not apply to products that have been repaired, except by Amantii or its authorized service representatives,
or otherwise altered. This limited warranty further does not apply to defects resulting from misuse, abuse, accident, neglect, incorrect
installation, improper maintenance or handling, or operation with an incorrect power source.
Products made by other manufacturers, sold with the product or thereafter, are not covered by this limited warranty. The use of unauthorized components will render this warranty null and void.
Service Under Limited Warranty
Defects must be brought to the atenton of Amanti Technical Service by contactng Amanti at (1-888-406-8764), or at
Davie Street Vancouer, BC V6E 4L2. Please have your proof of purchase, catalogue/model and serial numbers
available when calling; any and all service under the limited warranty requires a proof of purchase of the product.
# 502-1207
Defects
Should a product or part covered by this limited warranty be proven to be defective, in material or workmanship, and during the one
(1) year limited warranty period, Amantii will replace such defective product or part without charge. If Amantii is unable to replace
such product, or if replacement is not commerically practicable or cannot be timely done, in its sole discretion Amantii may, in lieu of
replacement, choose to refund the purchase price for such product or part.
Limitations
In no event will Amantii, including without limitation any of its directors, officers, shareholders, employees, consultants, agents, heirs,
executors, administrators and assigns, be liable to the purchaser or any third party, whether in contract, in tort, or on any other basis
for any indirect, special, punitive, exemplary, consequential, or incidental loss, cost or damage arising out of or in connection with the
sale, maintenance, use or inability to use the product, even if Amantii, including without limitation any of its directors, officers,
shareholders, employees, consultants, agents, heirs, executors, administrators and assigns, have been advised of the possibility of
such losses, costs or damages, or if such losses, costs or damages are foreseeable. In no event will Amantii, including without limitation any of its directors, officers, shareholders, employees, consultants, agents, heirs, executors, administrators and assigns, be liable
for any direct losses, costs or damages that exceed the purchase price of the product.
Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion
may not apply to the purchaser.
Application of Provincial and State law
This limited warranty gives you specific legal rights, and you may also have other rights which vary from jurisdiction to jurisdiction. The
provisions of the United Nations Convention on Contracts for the Sale of Goods shall not apply to this limited warranty or the sale of
products covered by this limited warranty.
General
Amantii reserves the right to make changes at any time without notice, in design, material, specifications, prices and the right to discontinue styles and products.
23
ELECTRIC FIREPLACES
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising