RMS510TS Owners Manual - Searchfield Electronics

RMS510TS Owners Manual - Searchfield Electronics
Owner’s Manual
Contents
Model Identification............................ 2
Precautions to avoid possible
exposure to excessive
microwave energy.................... 3
Important safety instructions.... 3
Commercial Microwave Oven
Keep these instructions for future reference.
If the oven changes ownership, this manual
must accompany oven.
Installation ......................................... 5
Earthing Instructions.......................... 5
Electronic Control Operation.............. 6
Dial Control Operation...................... 10
Care and Cleaning............................11
Before Calling for Service................ 12
Model
Identification
When contacting ACP, provide product information. Product information is located on oven serial plate which is
located on the back side of the oven. Record the following information:
Any questions or to locate an authorized ACP servicer,
call toll free 1-866-426-2621 inside the U.S.A or Canada,
or 1-319-368-8120 outside the U.S.A or Canada.
Warranty service must be performed by an authorized
ACP servicer. ACP also recommends contacting an
authorized ACP servicer if service is required after
warranty expires.
Model Number:______________________________
Manufacturing Number:________________________
Serial or S/N Number:_________________________
Date of purchase:____________________________
Dealer’s name and address:____________________
__________________________________________
__________________________________________
__________________________________________
2
IMPORTANT SAFETY INSTRUCTIONS
Recognize this symbol as a SAFETY message
!
WARNING
When using electrical equipment, basic safety precautions should be followed to reduce the risk of burns,
electrical shock, fire, or injury to persons.
1. READ all instructions before using equipment.
9. DO NOT heat baby bottles in oven.
2. READ AND FOLLOW the specific
“PRECAUTIONS TO AVOID POSSIBLE
EXPOSURE TO EXCESSIVE MICROWAVE
ENERGY” on this page.
10. Baby food jars shall be open when heated and
contents stirred or shaken before consumption, in
order to avoid burns.
11. DO NOT operate this equipment if it has a
damaged cord or plug, if it is not working properly,
or if it has been damaged or dropped.
3. This equipment MUST BE EARTHED. Connect
only to properly EARTHED outlet. See
“EARTHING INSTRUCTIONS” on page 5.
12. This equipment, including power cord, must be
serviced ONLY by qualified service personnel.
Special tools are required to service equipment.
Contact nearest authorized service facility for
examination, repair, or adjustment.
4. Install or locate this equipment ONLY in
accordance with the installation instructions in
this manual.
5. Some products such as whole eggs and sealed containers—for example, closed glass jars—are
able to explode and SHOULD NOT be HEATED
in this oven.
13. DO NOT cover or block filter or other openings on
equipment.
14. DO NOT store this equipment outdoors. DO NOT
use this product near water – for example, near a
kitchen sink, in a wet basement, a swimming pool,
or a similar location.
6. Use this equipment ONLY for its intended use as
described in this manual. Do not use corrosive
chemicals or vapors in this equipment. This type
of oven is specifically designed to heat, cook,
or dry food. It is not designed for industrial or
laboratory use.
15. DO NOT immerse cord or plug in water.
16. Keep cord AWAY from HEATED surfaces.
7. As with any equipment, CLOSE SUPERVISION
is necessary when used by CHILDREN.
17. DO NOT let cord hang over edge of table or
counter.
8. See door cleaning instructions in the product
safety manual.
18. For commercial use only.
PRECAUTIONS TO AVOID POSSIBLE
EXPOSURE TO EXCESSIVE MICROWAVE
ENERGY
A. DO NOT attempt to operate this oven with the door open since open door operation can result in harmful
exposure to microwave energy. It is important not to defeat or tamper with the safety interlocks.
B. DO NOT place any object between the oven front face and the door or allow soil or cleaner residue to
accumulate on sealing surfaces.
C. DO NOT operate the oven if it is damaged. It is particularly important that the oven door close properly and
that there is no damage to the:
1. door (bent)
2. hinges and latches (broken or loosened)
3. door seals and sealing surfaces.
D. The oven should not be adjusted or repaired by anyone except properly qualified service personnel.
SAVE THESE INSTRUCTIONS
3
IMPORTANT SAFETY INSTRUCTIONS
WARNING
WARNING
Liquids such as water, coffee, or tea are able to
be overheated beyond the boiling point without
appearing to be boiling due to surface tension of the
liquid. Visible bubbling or boiling when the container
is removed from the microwave oven is not always
present. THIS COULD RESULT IN VERY HOT
LIQUIDS SUDDENLY BOILING OVER WHEN A
SPOON OR OTHER UTENSIL IS INSERTED INTO
THE LIQUID. To reduce the risk of injury to persons:
To avoid risk of fire in the oven cavity:
a. DO NOT overcook food. Carefully attend oven
when paper, plastic, or other combustible
materials are placed inside the oven to facilitate
cooking.
b. Remove wire twist-ties from paper or plastic
bags before placing bag in oven.
c.If materials inside the oven ignite, keep oven
door CLOSED, turn oven off and disconnect
the power cord, or shut off power at the fuse or
circuit breaker panel.
i) Do not overheat the liquid.
ii) Stir the liquid both before and halfway through
heating it.
iii) Do not use straight-sided containers with narrow
necks.
iv) After heating, allow the container to stand in the
microwave oven for a short time before removing
the container.
v) Use extreme care when inserting a spoon or
other utensil into the container.
d. DO NOT use the cavity for storage. DO NOT
leave paper products, cooking utensils, or food
in the cavity when not in use.
!
CAUTION
To avoid personal injury or property damage, observe the following:
1. Do not deep fat fry in oven. Fat could overheat
and be hazardous to handle.
materials that are not intended for cooking.
9. When cooking with paper, plastic, or other
combustible materials, follow manufacturer’s
recommendations on product use.
2. Do not cook or reheat eggs in shell or with
an unbroken yolk using microwave energy.
Pressure may build up and erupt. Pierce yolk
with fork or knife before cooking.
10. Do not use paper towels which contain nylon or
other synthetic fibers. Heated synthetics could
melt and cause paper to ignite.
3. Pierce skin of potatoes, tomatoes, and similar
foods before cooking with microwave energy.
When skin is pierced, steam escapes evenly.
11. Do not heat sealed containers or plastic bags in
oven. Food or liquid could expand quickly and
cause container or bag to break. Pierce or open
container or bag before heating.
4. Do not operate equipment without load or food
in oven cavity.
5. Use only popcorn in packages designed and
labeled for microwave use. Popping time
varies depending on oven wattage. Do not
continue to heat after popping has stopped.
Popcorn will scorch or burn. Do not leave oven
unattended.
12. To avoid pacemaker malfunction, consult
physician or pacemaker manufacturer about
effects of microwave energy on pacemaker.
6. Do not use regular cooking thermometers in
oven. Most cooking thermometers contain
mercury and may cause an electrical arc,
malfunction, or damage to oven.
14. Clean oven regularly and remove any food
deposits.
13. An authorized servicer MUST inspect equipment
annually. Record all inspections and repairs for
future use.
15. To avoid surface deterioration, keep the oven
in a clean condition. Infrequent cleaning could
adversely affect the life of the appliance and
possibly result in a hazadous situation.
7. Do not use metal utensils in oven.
8. Never use paper, plastic, or other combustible
SAVE THESE INSTRUCTIONS
4
Installation
WARNING
Unpacking Oven
•
•
•
•
Inspect oven for damage such as dents in door or inside oven cavity.
Report any dents or breakage to source of purchase immediately.
Do not attempt to use oven if damaged.
Remove all materials from oven interior.
If oven has been stored in extremely cold area, wait a few hours before
connecting power.
Radio Interference
Microwave operation may cause interference to radio, television, or a similar
oven. Reduce or eliminate interference by doing the following:
• Clean door and sealing surfaces of oven according to instructions in
Care and Cleaning section.
• Place radio, television, etc. as far as possible from oven.
• Use a properly installed antenna on radio, television, etc. to obtain
stronger signal reception.
Oven Placement
•
•
•
•
•
Do not install oven next to or above source of heat, such as pizza
oven or deep fat fryer. This could cause microwave oven to operate
improperly and could shorten life of electrical parts.
Do not block or obstruct oven filter. Allow access for cleaning.
Install oven on level countertop surface.
Place warning label in a conspicuous place close to microwave oven.
Outlet should be located so that plug is accessible when oven is in place.
A
B
C
A—For North American (UL/CSA) models, allow at least 3” (7.6 cm) of clearance around
top of oven. For International (50 Hz) models, allow at least 12” (30 cm) of clearance
around top of oven. Proper air flow around oven cools electrical components.
With restricted air flow, oven may not operate properly and life of electrical parts is
reduced.
B—Allow at least 3” (7.6 cm) between air discharge on back of oven and back wall.
C—Allow at least 3” (7.6 cm) of clearance around side of oven. One side of oven must be
open.
Oven Clearances
5
To avoid risk of electrical shock
or death, this oven must be
earthed.
WARNING
To avoid risk of electrical shock
or death, do not alter the plug.
Grounding/Earthing
Instructions
Oven MUST be grounded.
Grounding reduces risk of electric
shock by providing an escape wire
for the electric current, if an electrical
short occurs. This oven is equipped
with a cord having a ground wire
with a grounding plug. The plug
must be plugged into an outlet that is
properly installed and grounded.
Consult a qualified electrician or
servicer if grounding instructions
are not completely understood, or if
doubt exists as to whether the oven
is properly grounded.
Do not use an extension cord.
If the product power cord is too
short, have a qualified electrician
install a three-slot receptacle.
This oven should be plugged
into a separate circuit with the
electrical rating as provided in
product specifications (available at
www.acpsolutions.com). When a
microwave oven is on a circuit with
other equipment, an increase in
cooking times may be required and
fuses can be blown.
External Equipotential
Earthing Terminal (export only)
Equipment has secondary earthing
terminal. Terminal provides external
earthing connection used in addition
to earthing prong on plug. Located
on outside of oven back, terminal is
marked with symbol shown below.
Electronic Control Operation
So...how do I use it?
1. Power Up
“-- -- ” displays when the oven is powered up for the first
time. If
Mode.
key is pressed, the oven will change to Idle
Note: In Idle mode, no key can be pressed.
2. Idle Mode
(1)
1)The oven will enter Idle Mode after a set number
of seconds have expired in Ready Mode without a
keypad pressed or without the door being opened and
closed. The default number of seconds is 60 and maybe
changed by resetting User Option 4.
2) During Idle Mode, LED is blank. There will be no oven
activity.
(2)
3) Open and close the oven door to exit the Idle Mode
and go into Ready Mode.
3. Ready Mode
(3)
1) In this mode, the oven is ready to either begin a
manual or preset cook cycle.
(7)
2) Opening and closing the door while the oven is in Idle
Mode will put the oven into Ready Mode.
(4)
3) During Ready Mode LED displays “0:00”.
(5)
4. Door Open Mode
1) While the door of the oven is open, the oven will
be in Door Open Mode. This allows for entry into
Programming Mode.
(6)
2) During this mode, LED is blank, the fan operates and
oven light is on.
(1) LED Display
(2) Power Level Keys
(3) Time Entry Key
(4) Stop/Cancel Key
(5) Start Key
(6) X2 Key
(7) Number Keys
3) When the door is opened and closed, if User Option
OP:60 is selected and the oven was running a manual or
preset cook cycle, the oven will enter Pause Mode.
If User Option OP:61 is selected and the oven was
running a manual or preset cooking cycle, opening
and closing the door will clear all preset cook cycle
information.
The switching operation of this microwave oven can cause voltage fluctuations on the supply line. The operation of this oven under unfavorable voltage
supply conditions can have adverse effects. This device is intended for the connection to a power supply system with a maximum permissible system
impedance Zmax of 0.2 Ohms at the interface point of the user’s supply. The user has to ensure that this device is connected only to a power
supply system which fulfills the requirement above. If necessary, the user can ask the public power supply company for the system impedance at
the interface point.
6
Electronic Control Operation
5. Pause Mode
(3) If either User Option OP:11 or OP:12 is selected, the
oven will continue to sound until the user acknowledges
by either opening and closing the door or pressing the
1) This mode allow users to temporarily stop the cooking
cycle to inspect or stir the food item.
key. User Option OP:10 is the default and after the 3
second beep, the oven will go into Ready Mode.
2) While in Time Entry Mode or Preset Program Cook
Mode, if the door is open and closed, or if the
pressed, the oven will enter Pause Mode.
key is
9. Preset Program Cook Mode
1) This mode allows cooking of food items through a one
key touch operation. While in Ready Mode, pressing a
Number Key on the keypad will cause the oven to run
the Preset Program associated with that key.
3) While paused, LED will display the remaining cooking
time.
4) Pause Mode will expire back to Idle Mode in the exact
fashion as Ready Mode, dependent on User Option 61.
5) Additionally, if the
2) LED displays the remaining cooking time. If it is multistage cooking, the total remaning cooking time displays
not a particular stage cooking time.
key is pressed, the oven will
immediately enter Ready Mode. If
key is pressed,
the oven will resume the cooking cycle.
(3) If the program chosen exceeds the maximum time
allowed by User Option 7, then the oven will beep three
times and display 00:00 to indicate the program is
unacceptable.
6. Time Entry Mode
1) The user may manually enter a cook time and power
level while in this mode.
(4) When the cooking program finishes, the oven will
2) While the oven is in the Ready Mode, pressing the
key
enter End of Cook Cycle Mode. If you press
while in this mode, the oven will enter Pause Mode.
key will put the oven into Time Entry Mode.
3) During this mode, “00:00” displays.
10. On the Fly Cooking
1) The user may start another cook cycle while the oven
is operating or paused.
4) Press
,
,
, or
key to
select power level, LED will display the related power.
If the same key is pressed twice, the power will change
to PL10 ( Power Level 10 or full power). If no power
chosen, PL10 is default.
5) During setting process, press
2) While the oven is operating or while in the Pause
Mode and if User Option OP:51 is selected pressing a
Number Key will automatically start the preset cooking
program associated with the selected number key.
key to enter Time
Entry Mode and begin cooking. Press
Ready Mode.
3) LED displays the remaining cooking time.
key to enter
4) When cooking program finish, the oven will enter End
key while in this
of Cook Cycle Mode. If you press
mode, the oven will enter Pause Mode.
7. Manual Cook Mode
1) This mode allows cooking of the food items. While
11. Programming Mode
in Manual Cook Entry Mode, pressing the
key will
cause to the oven to begin Manual Cook Mode.
1) This mode allows the user to assign cook times and
power levels to the keypad number keys.
2) During this mode, cooking time displays. The fan
operates and oven light is on.
2) Open the door and press Number Key 1 for
5 seconds. The buzzer sounds once to indicate
Programming Mode is activiated.
3) When cooking program is finished, the oven will enter
key while in
End of Cook Cycle Mode. If you press
this mode,the oven will enter Pause Mode.
3) LED displays “ProG”.
8. End of Cook Cycle Mode
4) Press
key, LED will display the saved time. Input
the desired new time.
1) After the time has expired in a Manual Cook Mode, or
a Preset Program Cook Mode, the oven will go into The
End of Cook Cycle Mode.
5) Press
(2) During this mode, “End” displays.
7
,
,
, or
to input the power level.
LED will display the related power. If the same key is
pressed twice, the power will change to PL10 ( Power
Level 10 or full power). If no power chosen, PL10 is the
default.
Electronic Control Operation
6) If X2 is pressed, LED displays “CF:80”. The default
factor of 80%. To change the cooking factor, press
desired Number Key for new factor.
Example: If number “5” key is programmed to cook
for 1:00, when first pressing X2 key and then pressing
number “5” key, the oven will automatically set the cook
time to 1:48. (1:00 cook cycle x 80% “X2” cook factor =
1:48)
7) After setting the time and power, press
key to
save the cooking program. LED displays “ProG”.
4) When the cooking program finishes, the oven will
enter End of Cook Cycle Mode.
8) If total cooking time entered exceeds the maximum
time allowed User Option 7, when
key is pressed
to save the program. If the program chosen exceeds the
maximum time allowed by User Option 7, then the oven
will beep three times and display 00:00 to indicate the
program is unacceptable.
Note: X2 function may be used only with Programming
Mode cooking.
13. Stage Cooking Programming
1) This allows food items to be cooked using a
combination of various Power Levels and times.
9) Close the door and the oven will return to Ready
Mode.
Press
Mode.
2) A maximum of three stages can be set.
key and the oven will return to Door Open
After setting the power and time for the first stage, press
key to set the second stage.
10) Program example for a cook setting of 1 minute and
25 seconds at 70% power.
Repeat to set the third stage.
Step1: Open oven door and press Number Key “1” for 5
seconds, LED displays”ProG”.
3) When setting the second and the third stage, press
Step 2: Press Number Key “3”. The program will be
saved in “3”.
4) Press
Step 3: Press
key LED displays “S-2” or “S-3”.
Program example for two stages. Stage 1: 1 minute 25
seconds @ 70% power; Stage 2: 5 minutes 40 seconds
@50% power.
key, LED displays “0:00”.
Step 4: Press Number Keys “1”, “2” and “5” to input the
cooking time, LED displays 1:25.
Step 5: Press
displays “PL7”.
key to start cooking.
Step 1: Open oven door and press Number Key ”1” for
5 seconds LED displays “ProG”.
key to input 70% power level. LED
Step 2: Press Number Key “3”. The program will be
saved in “3”.
Step 6: Press
key to save. To use this program
press “3”. The oven will start operating for 1:25 @70%
power.
Step 3: Press
key, LED displays “00:00”.
Note:
Step 4: Press Number Keys “1”,”2”,”5” to input the
cooking time. LED displays “1:25”.
1. If the electric supply is interrupted, the saved program
will not be lost.
Step 5:. Press
displays “PL7”.
key returns the oven to Ready Mode
2. Pressing
and cancels entered settings
The first stage is finished.
Step 6: Press
12. Double Quantity Cooking
key to input 70% power, LED
key, LED displays “S-2”.
Step 7: Press Number Keys “5”, “4”,”0” button, LED
displays “5:40” .
1)The X2 pad allows two quanities of the same food item
to be cooked at once
”keyto input 50% power, LED displays
Step 8: Press “
“PL5”. The second stage is finished.
2) Press X2 key and then Preset Program Number(s)
0-9 with in 5 seconds. The oven will start cooking per the
quantity preset cooking time.
Step 9: Press
key to save. To use this program
press “3”. The oven will start operating for 7:05 (1:25 @
70% power + 5:40 @50% power).
3) Press X2, LED displays “doub”. Press
preprogrammed number key, LED displays the cooking
time for two quanities.
8
Electronic Control Operation
14. Use Option Mode
1) This allows the user to choose various oven
operations.
5) Press
key to save the selected setting. LED
displays “OP: - -” to indicate selection was saved and
another option change can be made.
2) Open the oven door and press Number Key “2” for
5 seconds. The buzzer sounds once to indicate User
Option Mode is activated.
key to
6) During programming process, press
enter Door Open Mode. Close the door will enter Ready
Mode.
3) LED displays “OP: - -”.
7) If
key is not pressed as the last step, the
selected option will not be saved.
4) Press any Number Key to enter related options as
noted in chart below.
15. Inqury Function
Example: To set the buzzer or key beep volume to
medium, Press Number Key “2“ “OP:22” displays.
During the cooking process, press
the power level.
To change, repeat pressing “2” LED displays “OP:20”,
“OP:21” ”OP:22” ”OP:23” etc.
Number Keys
1
End of Cycle Beep
Display
LED will display the power level for 3 seconds and then
return to remaining cook time display.
Options (Factory Settings in Bold)
OP:10
3 second beep.
OP:11
Continuous beep until door is opened.
OP:12
5 beep bursts until door is opened.
2
OP:20
Eliminates beep.
Key Beep Volume
OP:21
Sets volume to low.
OP:22
Sets volume to medium.
OP:23
Sets volume to high.
OP:30
OP:31
Prevents beep when Number Key is pressed.
Allows beep when Number Key is pressed.
OP:40
15 seconds after oven door is opened, keyboard disabled.
OP:41
30 seconds after oven door is opened, keyboard disabled.
OP:42
1 minute after oven door is opened, keyboard disabled.
3
Key Beep
4
Active Display
key to check
OP:43
2 minutes after oven door is opened, keyboard disabled.
5
OP:50
Prevents different pre-programmed Number Key to be activated during cooking.
On-the Fly Cooking
OP:51
Allows different pre-programmed Number Key to be activated during cooking.
6
OP:60
Opening oven door does not reset oven back to ready mode.
OP:61
Opening oven door resets oven back to ready mode.
OP:70
Allows 60 minutes of heating time (some models).
OP:71
Allows 10 minutes of heating time.
Reset to Ready Mode
7
(some models)
Maximum Heating Time
8
Manual Operation
9
(some models)
Double Digit Operation
0
Clean Filter Message
OP:80
Allows use of preprogrammed Number Key only.
OP:81
Allows use of manual time entry and preprogrammed Number Key.
OP:90
Allows 10 (0-9) preprogrammed Number Key.
OP:91
Allows 100 (00-99) preprogrammed Number Key.
OP:00
Do not display message.
OP:01
Display message for 24 hours every 7 days.
OP:02
Display message for 24 hours every 30 days.
OP:03
Display message for 24 hours every 90 days.
9
Dial Operation
So...how do I use it?
Heating
Menu Guide
2:00
:15
1:00-2:00
:45
:30
1:30-2:30
1. Open oven door, place food in oven, and close oven door.
2. Turn time entry knob clockwise to desired time.
• Cooking time can be set up to 6 minutes.
• Oven begins operation and time counts down.
3. When cooking time has elapsed, microwave energy stops and oven
signal sounds.
Interrupting Operation
Open oven door to interrupt operation or turn time entry knob
counterclockwise to “0”.
When cooking is interrupted by opening door, oven automatically resets to
zero time.
To resume microwave oven operation, close door and re-enter desired time
by turning knob clockwise.
Changing Time and Canceling Mistakes
Heating time can be changed at any time while the oven is operating.
Turn knob to desired new setting. To set cooking time to zero, turn knob
counterclockwise to “0”. Setting the time to zero cancels the set cooking time
and turns the oven off.
10
Care and Cleaning
!
WARNING
To avoid electrical shock which can cause severe personal injury or death, unplug power cord or open
circuit breaker to oven before cleaning or removing light bulb.
DO NOT power spray
PART
No metal pans
CARE AND CLEANING RECOMMENDATION
Interior, Exterior, and Door
Clean microwave oven with mild detergent in warm water using soft sponge or cloth.
Wring sponge or cloth to remove excess water before wiping equipment. If desired, boil a
cup of water in microwave oven to loosen soil before cleaning.
Important:
•
•
•
Do not use abrasive cleansers or cleaners containing ammonia or citrus.
These could damage finish.
Never pour water into microwave oven bottom.
Do not use water pressure type cleaning systems.
Discharge Air Vents
Check monthly for a buildup of cooking vapors along intake and discharge louvers on
bottom and back of oven. Clean air vents with damp cloth to ensure proper airflow. Dry
thoroughly.
Control Panel
Open oven door to deactivate oven timer. Clean with mild detergent in warm water using
soft sponge or cloth.
11
Before Calling for Service
!
WARNING
To avoid electrical shock which can cause severe personal injury or death, do not remove outer case at any time.
Only an authorized ACP servicer should remove outer case.
Troubleshooting
Complaint
Dim oven light
Steam forms on oven
door
Hot air expelled from
vents
Oven does not start.
Possible Cause
Cooking at low power level.
When cooking foods in a microwave steam is generated.
Foods cooking in a microwave
may release heat.
Power cord not plugged in correctly.
Fuse blown or circuit breaker
open.
Malfunctioning outlet
Door not closed.
Part No. 20042802
Revised 10/10
Remedy
This is normal
This is normal
This is normal
Plug cord into outlet correctly.
Replace fuse (should be repaired
by authorized servicer) or reset
breaker.
Test outlet with other electrical appliances.
Close door.
For full product documentation visit:
www.acpsolutions.com
12
 2010 ACP, Inc.
Cedar Rapids, Iowa 52404
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising