LG | LD-14AT3 | LG LD-14AT3 User manual

LG LD-14AT3 User manual
DISHWASHER
OWNER'S MANUAL
MODEL
:
LD-14AT 3
Please read this manual
carefully
before
operating your
dishwasher. Retain it for future reference.
Capacity
14 Place
Dimension
600x600x850mm(WxDxH)
Weight
52
Power
Supply
See
rating
label
Power
Consumption
See
rating
label
Water
Consumption
See energy label
Water Feed Pressure
P/No.: 3828DD7001X
settings
kg
50~800kPa
CONTENTS
SAFETY AND CAUTION
IMPORTANT SAFETY INSTRUCTIONS
WARNING
?
?
Please read this manual
using your dishwasher, follow
including the following:
When
carefully before
the
installation,
use
?
and
maintenance of your dishwasher.
The manufacturer can not be responsible
?
for
?
SAFETY AND CAUTION
3
?
?
INSTALLATION INSTRUCTION
4
?
PARTS NAME
FUNCTION OF CONTROL BUTTON
HOW TO USE AND OPERATE
8
9
WASH OPTIONS
15
mains.
This appliance must be positioned so that
the plug is accessible.
Controls may be locked using "child lock"
mode to prevent from interrupting
Do not
use
the dishwasher for industrial
16
?
CHECK AND CARE
17
?
cord.)
?
Only suitable household utensils should
be placed in the dishwasher. (Please avoid
18
?
SPECIFICATIONS
?
?
are
metal
?
away from children.
If the hot water exceeds 65˚C, adjust the
water heater setting. If the hot water
may
cause an
Do not expose skin to vapor vent.
During operation, as hot steam may scald.
?
Dishwasher detergents are strongly
alkaline. They can be extremely
dangerous if swallowed. Avoid contact
with skin and eyes and keep children
away from the dishwasher when the door
is open.
explosion
Do not spray water on the appliance. It
may cause the failure of electric parts or
electric shock.
Do not allow children to operate the
dishwasher.
Do not push down or sit on the inner door
?
when the door opened. It may cause the
deformation or failure of your dishwasher.
Do not use the detergent for hand
washing.
The detergent for dishwasher
supervision.
Young children should be supervised to
ensure that they do not play with the
appliance.
Do not insert anything such as coin into
?
not be maintained
They
dishwasher accidentally.
The appliance is not intended for use by
young children or infirm persons without
parts and noise.
below
65˚C, the dishwasher must be connected
to cold water.
Do not use any kinds of solvent in your
can
the
the vapor vent.
It may cause the failure of mechanical
Keep detergents
dishwasher.
or fire.
?
TROUBLE SHOOTING GUIDE
?
accordance with the rating label.
Electrical safety is only guaranteed when
the earth system of your house is in
temperature
PROGRAMS
?
and commercial use, or other purpose.
Electrical connection must be in
or
automatically stops
operation of the dishwasher when it is
exposed to heavy disturbance on its
use.
utensils;
non-heartresistant,
decorated, etc.)
?
person in order to avoid a hazard.
This appliance is fitted with a safety
household
that
?
operation.
If power supply cord is damaged, it must
only be replaced by the manufacturer or
its service agent or a similar qualified
function that
cable
10
precautions,
problems caused by ignoring these
safety and caution instructions.
This dishwasher is designed for normal
accordance with the related local
regulations. (Do not use an extension
?
basic
used for normal
using the dishwasher for the first time.
This manual contains very important notes
regarding
?
-
?
should be
Check that the detergent receptacle is
empty after completion of the wash cycle.
The appliance is to be connected to the
water mains using new hose-sets and that
old hose-sets should not be reused.
Some pre-treatment sprays or liquids
can damage your dishwasher's control
panel and plastic components, so do not
use these products on or around your
dishwasher.
3
INSTALLATION INSTRUCTION
INSTALLATION INSTRUCTION
Step1:
Step2:
Step3:
Step4:
PREPARE CUPBOARD OPENING
PREPARE ELECTRICAL WIRING
PREPARE DISHWASHER FOR
INSTALL THE DISHWASHER IN
INSTALLATION
CUPBOARD
1
This dishwasher is
size shown
as
designed
to fit to the
CAUTION
below.
For
2
Select
a
location
as
close to sink
as
this
or
appliance.
Electrical and
grounding
the dishwasher
1
Lay
2
Adjust
the
cabinet
as
legs
on
its back.
to the needed
shown in below
height
figure.
1
of
connections must
electrical
The dishwasher should not be installed
more
house fuse
open circuit breaker before installation. Do not
use an extension cord or adapter plug with
possible for easy connections to water and
drain lines.
3
personal safety,
remove
comply with the national
code/provincial and municipal code
and/or other local codes.
2
than 3 meters from sink for proper
a
corner,
minimum 5cm of space is required
between the washer and an adjacent
a
This
appliance must be supplied with
correct rating voltage and hertz as shown
on
kinked
instruction manual, and connected to
individual, properly grounded branch
circuit, protected by minimum 15 amp
wall.
Wiring
2
or
must be 2
time
delay
wires with
If the
that the
fuse.
ground.
The power plug must be in a accessible
location adjacent to and not behind the
dishwasher
3
side.(See
page 6
Fig.A)
The power plug must be correctly
earthed, if in doubt, have it checked by a
qualified
Electrician. No other
should be connected to the
outlet
by
a
double
adapter
appliance
same plug
or
similar
plug.
Unit:mm
chipboard
is
adjacent
to or above the
dishwasher, it should be sealed with a
waterproofing paint or sealant to prevent
due to steam.
4
or
stretched.
is below 850mm, you
should remove the top table by unscrewing
the 2 screws. (Two of rear)
dishwasher and within 1.2 meters of the
swelling
sure
CAUTION
an
circuit breaker
If bare
Make
drain hose inside the cabinet is not
If dishwasher is to be installed in
or a
Slide the dishwasher into the cabinet
opening carefully.
1
cabinet
sliding the dishwasher into the
cupboard opening, all necessary final
height adjustment and balancing
adjustment should be done using the
spanner.
drainage.
4
Before
5
height
of
cupboard
INSTALLATION INSTRUCTION
INSTALLATION INSTRUCTION
Step5:
Step6:
Step8:
DRAIN LINE CONNECTION
WATER SUPPLY CONNECTION
HOW TO LEVEL THE PRODUCT
1
If the end of drain hose does not fit to
When the drain hose is connected to
the drain line,
separate stand pipe, it is essential that
piece of rubber
connector(not supplied) that must be
resistant to heat and detergent and may
be obtained from a plumbing shop.
2
There
are
shown in
use a
2
typical connections
Figure A, B.
air
tight
Refer to
1
a
Connect the water
supply hose
to the
After
valve behind dishwasher and the water
an
tap
connection is made.
as
shown in
figure.
product.
Case 1. In
case
the door is slanted to the
right
2
connecting, the sealing tape or
sealing compound should be used to
When
avoid water leaks.
Make
sure
sharply
that the line is not kinked
or
bent.
S
drainage.
Fig. C
one
of the
following
?
Water
instruction methods must be followed:
When the drain hose is connected to
tap
a
sink "s" trap or waste disposal unit, the
hose must be looped up to the underside
Fig.
of the bench top and secured.
B
:
Drainage
connection
-
stand
pipe.
Water
Drain Hose Extension
Extend Drain Hose
as
supply
?
hose
shown below.
If the door is slanted to the
right as shown in
figure C, repeat the procedure shown as
below until the door is operated normally.
1) Unscrew(counter-clockwise) the left leg of
back side and high the level.
2) Check the opening of door if there still
remains sticky or friction sound.
When the product is correctly leveled, there
do not remain slant, stickiness
sound.
Valve
Case 2. In
case
or a
friction
the door is slanted to the left
Step7:
FINAL CHECK AND
ASSEMBLING
1
Fig.
2
as
maximum internal diameter, if used for
prevent siphoning,
product, if you feel some
frictional sound between the
and tub when you open or
close the door, you have to adjust the level of
maintained below 65ºC, the dishwasher
must be connected to cold water.
The "S" trap spigot must be drilled out
cleanly and free of obstruction to its
To
1
the
sticky or hear a
side portion of door
This dishwasher may be fed with either
hot or cold water. If the water can not be
Fig.B
installing
SW
A
CAUTION
When you connect or extend Drain Hose,
make sure that drain hose is not kinked.
(Bends should have
6
40
mm
radius.)
2
Securely hand tighten supply hose to
water supply.
Plug power supply cord into an
earthed the power plug and switch on.
Fig.
?
D
If the door is slanted to the left
conditions.
?
7
shown in
the
procedure shown as
below until the door is operated normally.
1) Unscrew(counter-clockwise) the right leg
of back side and high the level.
2) Check the opening of door if there still
remains sticky or friction sound.
When the product is correctly leveled, there
figure D, repeat
Operate the dishwasher through one
cycle (Quick cycle is recommended)
to check for water leak and operating
as
do not remain slant, stickiness
sound.
or a
friction
PARTS NAME
FUNCTION OF CONTROL BUTTON
DELAY START
TIME SAVE
BUTTON
If you want to
?
delay
?
This function is for
?
of small load,
In
case
lower rack only to
saving time and
or
program, press this
button before
energy.
With each press, time
energy.
With each press,
pressing start button.
Pressing the delay
?
HALF LOAD
the start of selected
?
save
time
?
ON and OFF is
or
repeated.
time will increase
?
by
1 hour.
?
When select this
lower rack
BUTTON
use
upper
can
select upper
only.
case
time will be shorten.
operate upper and lower spray
arm
washing, which
alternately.
11.
Adjust Leg
2. Control Panel
12.
Upper
3. Door Handle
13.
Cutlery
4. Front Cover
14.
Detergent
5. Lower Cover
15.
Vapor
6. Process Monitor
16.
Upper Spray
7. Power Switch
17. Lower
8. Drain Hose
18. Filter ASM
9. Inlet valve ASM
19. Lower Rack
Vapor
vent
?
After
operating, this
button automatically
switches off for safety
and energy saving.
If case of irregular surge
disturbances to the
machine, the power may
be
automatically turned
off for safety.
1 hour to 19 hours.
1.
?
you don't select this
button, the machine always
In
For operating, press this
button first for power
on.
works vario
delay start time
can be adjusted from
?
save
function, the operating
The
?
POWER SWITCH
Rack
Rack
& Rinse Aid
Dispenser
Vent Cover
Spray
Arm
Arm
10. Power Cord
REMAINING
TIME
Indication of
?
?
8
or
remaining
time
buttons to prevent all
the setting from being
Self
and
child.
message
changed by
For locking/unlocking,
press Delay Start and
display
T-Save button
error
Inlet Hose
Used to lock
?
?
unlock the control
diagnosis
PROGRAM
CHILD LOCK
a
?
simultaneously.
When power is
on, program is
automatically
set
to normal.
?Ifyouwantto
change the
?
RINSE/
START/PAUSE
SANI
BUTTON
With each
press,
rinse+,
repeated during
operation.
rinse+ &
77 C sani
With each press,
Start and Pause is
?
?
If the machine
rinse,
remains in Pause
program, press the
button and set the
77 C sani
mode for 10
rinse is
minutes, the power
program you want
repeated.
is
to.
automatically
turned off.
9
HOW TO USE AND OPERATE
1.
Be careful
large items not to prevent
the detergent dispenser lid from
opening
Dishwasher
your
Loading
HOW TO USE AND OPERATE
For the best
washing performance, it is important
that the dishwasher is loaded according to
instructions.
3.
Before
loading items into the dishwasher, you
must scrape off large particles in particular non
soluble items such
as
bones, toothpicks, pips,
etc.
Using
Cutlery
loading the dishwasher,
following general guidelines:
observe the
nesting
the
crockery such that water will contact
all surfaces.
hinged
and
clipped
Deep based items should be placed at an angle
to help water run off and dry properly.
knives located at upper rack.
Items with burnt
Take
prior to loading
cover
away from the
basket if you choose not to use them.
For the knives, place at seperate rack for
can
Position
cutlery
with the handles down. The
scraps should be soaked
in the dishwasher.
on
care
sharp
when
loading
and
Loading
the
Upper Rack
5.
Adjusting
the
Upper
Your upper rack can be raised or lowered to
cater for different size of crockery. Before
cups, glasses and dishwasher safe plastic
items. Plates should be positioned upwards
adjusting, ensure rack is empty of
all crockery.
You can change the position of the upper
rack by pulling the rack upward(to upper
position) or pulling the two levers on the
left and right sides of the rack to take the
rack down (to lower position).
plate
bottom
facing
the front of the
rack.
Cups, glasses
upside down.
and bowls must be
positioned
Extra cups or cooking utensils can be laid
on the fold down cup racks which may also
provide support for long stem glasses.
Take
spray
care
arm
It is recommended to level the upper rack
gently for more convenience and correct
not to obstruct the rotation of the
operation.
under the upper rack.
And when you pull the rack upward, hold
the middle location of the upper rack
unloading
(
items.
marked
position)
After adjusting, check that the spray
is free to rotate.
2.
Loading
the Lower Rack
Front
The lower basket is best loaded with dinner
soup bowls, dishes, pots, pans, lids
and even the grill tray.
plates,
Plates should be
facing
positioned upright
the center of the rack.
Pots, pans and large dishes
upside
Take
Non Dishwasher Safe Items
and
The combination of high water temperatures and
dishwasher detergent may damage particular
must be turned
down.
care
items, therefore
not to obstruct the rotation
of the spray
we
do not recommend
dishwasher to wash the
arms.
using the
following:
Copper or anodized aluminum
Hand painted silver or gold leaf crockery
Wood
Iron
or
bone handled utensils
or non
rust
WARNING
proof utensils
Plastic items which
10
Rack
The upper rack is best loaded with more
delicate items, small plates, long cutlery,
with the
basket to prevent
of similar items. Place the cutlery in
cover
be
Cutlery
Basket
should be mixed within each
section of the
When
the
4.
are
not
Before
adjusting, ensure rack is
empty of all crockery.
Otherwise crockery may be
damaged or you may be injured.
dishwasher safe.
11
arm
HOW TO USE AND OPERATE
6.
?
HOW TO USE AND OPERATE
7.
Adding Detergent
Dispenser
Detergent
must be
chamber before
put into the
starting
Adding Rinse
Dispenser
To fill the Rinse Aid
detergent
every program
Push latch to open
except the Pre-Wash.
Use
only
the
detergent
washing detergent
because the foam
?
(Ordinary
hand-
Rinse Aid, then
good quality
replace
the
automatically dispensed
final rinse cycle.
interfere with proper
the
operation.)
Chambers hold
number of washes, the chamber may need
only to be topped up once per month. The
15g
and
Place proper
25g.
The amount of
program.
detergent depends
Refer to the guide table.
on
the
on
rinse aid level
into this
dosage setting
and the
Depending
detergent
?
a
during
should not be used,
can
rotate the
and lock the cap.
The Rinse Aid is
intended for
household dishwashers.
chamber,
round cap counter clockwise and remove.
Fill the container to the maximum level
with
?
Aid
can
be checked
by looking
at
the indicator window when the dishwasher
compartment
door is
fully
open.
Black indicates sufficient Rinse Aid
PROGRAM
AMOUNT OF DETERGENT
Intensive
25g
O Clear indicates Rinse Aid
Normal
20g
The
Eco
dosage setting
most installations.
15g
required
is
factory set to suit
If, after washing, you
notice
Gentle
10g
Quick
10g
Pre-Wash
?
After the
Detergent
detergent
No
is
Use
detergent
supplied,
the
detergent
intended for
household dishwashers.
washing detergent
the
because the foam
chamber lid should be closed.
?
only
Information
(Ordinary hand-
should not be used,
can
interfere with proper
operation.)
cloudy spots, streaks or water marks
on your glassware, it may be necessary
increase the setting. To do so, remove the
cap and rotate the indicator arrow to a
higher setting then replace the cap If the
.
on
are
smeared
Rinse Aid Information
there is foam present
the bottom of the glass or the bottom of
glasses
the machine. Select
or
a
lower
setting.
Rinse Aid is necessary in order to get spot
and streak free dishes as well as improved
The
detergent is dispensed automatically
during the operation.
drying. Using the correct amount will
improve wash performance. However, using
too much can produce excess foam leading
to possible water leaks.
WARNING
?
The chamber lid remains open after
The
detergent
detergent and
operation.
used is
a
special
Dishwasher
like all household chemicals
should be treated
poison and kept out
of reach of children. At completion of each
wash program, the detergent compartment
should be checked and any remaining
detergent removed.
12
as a
13
HOW TO USE AND OPERATE
8. Fold down dividers.
Fold-down dividers at the lower rack
lowered to
improve stacking
can
10.
be
of pots and pans.
?
?
?
?
?
?
Energy Test
(AS / NZS 2007)
Appliance loaded in accordance with
standard specifications.
Example of loaded dishwasher : p.10~11
Capacity : 14 place settings
Comparability course : Economy with
Rinse+ (R+1) option.
Rinse aid setting : 3
Reference cleaner : 6g of detergent onto
the inside surface of the door and fill 24g
into the detergent dispenser.
Height-adjustable Rack-U must be
inserted in the uppermost position.
WASH OPTIONS
Before
the wash program, press the power button. Then Normal
program will be selected with remaining time on display window. To change the
program, press the program button required.
selecting
Start / Pause Button
After
or
Child Lock
wash program, press the Start
Pause button to start the wash cycle.
selecting
To reduce the
a
interrupting
If at any time you want to interrupt the
washing cycle, press the Start or Pause button.
possibility
of children
the dishwasher when
unattended, the child lock feature
can
be
selected.
Your dishwasher will then pause. Press the
Start or Pause button again to re-start
For
dishwasher.
Start" and "T-Save" buttons
locking
or
unlocking,
press
"Delay
simultaneously.
Progress Indicators
Sani-Rinse
Once you select a program, the progress
indicators light(Wash, Rinse, Dry). When press
the Start or Pause button to start the program,
When you want to rinse dishes with higher
temperature for sanitation, use this function
the current stage
at any program. If you choose this
light
will blink.
function,
the water temperature goes up to 77˚C when
Delay
9.
This function enables the wash
Drying
anywhere
fully open the
door to assist in
cycle
drying.
Set the
Press Rinse button until
to start
With each press, upper rack only(Upper
light on), lower rack only(Lower light on)
delay
time you want
can
In
be started
automatically after the delayed
shown in the display has expired.
Rinse Plus
when you select any program, the
Rinse process is done only two ( 1 normal
Normally
rinse +1
1
heating rinse) or three (2 normal rinse
heating rinse) times according to selected
program. But if you want to rinse more, you
can use this function. As you select R+1 with
pressing
done
14
Rinse button, the normal rinse will be
one
time
be selected.
case
of small load
lower rack
Press the start button. Then the program will
+
on.
Half Load
by using
by pressing the
"Delay Start" button. The delay start time is
increased by 1 hour for each pressing.
time
"R77˚" is lighted
between 1 to 19 hours later.
Select the program that you want
the program button.
At the end of the program, it is recommended
to
rinsing.
Start
more.
15
only
washing,
use
to save energy.
upper
or
PROGRAMS
CHECK AND CARE
To prevent trouble and poor operating, it is
filters and spray arms at intervals.
important
Filters
Remove the lower rack first.
?
?
Turn the mesh filter counterclockwise off.
?
?
Take out the mesh filter, upper STS filter
and out filter.
?
?
Eco Wash with
Intensive Wash
This program is for
including pots,
heavily
Rinse+
soiled loads
pans and casserole dishes.
Normal Wash
This program is for
everyday loads.
normally
option
This program is for
everyday loads.
soiled
normally
Check that the water jet holes
blocked
?
by
?
food
are
not
remove
the
particles.
When necessary to clean,
by pulling
soiled
Arm
Spray
arm
up.
Clean the spray
down.
arm
and
replace by pushing
Gentle Wash
This program is for
items like glasses.
washing
delicate
Eco Wash
This program is for
loads.
light
soiled
Quick Wash
everyday
This program is for that quick wash of
lightly soiled recently used dishes and
cutlery.
16
Pull the upper rack forwards.
Check that the water jet holes
blocked
Clean them if necessary.
Replace them in the reverse order.
Lower
Arm
Upper Spray
?
?
to check and care for the
17
by
food
are
not
remove
the
particles.
?
When necessary to clean,
by unscrewing the nut.
?
Clean the spray
reverse order.
arm
and
replace
arm
it in the
TROUBLE SHOOTING GUIDE
If
a
problem
occurs
Memo
in your machine, call for service.
Before you call for service, check the below instructions to
problem can be solved by yourself first.
on
do not
lamps
come
when the power switch
on.
The machine does not start.
Water is not
pumped
show
"
shows
"
(The display
The
display
(Automatically
The
The
The
display
display
The spray
Drain
away.
"
"
code)
code
Pump operated)
?
Fuse blown
?
The
?
Door is not
?
The start button is not
?
The drain hose is kinked.
?
The filter is
?
Excessive water is
?
The inlet valve is troubled.
fully
was
cut
off.
closed.
pressed.
clogged. (Clean
the
filter)
supplied than
normal water level.
?
Water is not
shows
"
"
code
?
Water
?
Water is leaked
?
The circuit of Heater is troubled.
?
The
mounting of spray arms is blocked by food
particles. (Clean the holes of the spray arm)
?
The amount of
?
Too little Rinse-aid
dispensed.
?
Too little Rinse-aid
dispensed.
?
Incorrect amount of
"
"
code
does not rotate
are
on
are
not
results
left
on
the
supplied. (Water tap
leakage
is not
opened)
in Hose connections
by damages.
detergent
or
rinse-aid set
incorrectly.
washing.
left
Washing
satisfactory.
of the house
electricity
tripped.
code
dish washer after
Dry
circuit breaker
shows
deposits
results
or
"
arms
are
properly
inserted in the socket.
Plug
smoothly
Streaks
is not
?
"
shows
display
White
whether the
Possible Causes
Problem
The
see
glassware
satisfactory.
are
not
?
?
?
?
?
detergent.
Utensils incorrectly arranged or overloaded.
Filters are clogged.
Water jet holes of spray arms blocked.
Spray arms' rotation obstructed by utensils.
Unsuitable program selected.
18
19
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising