Cypress | PCHD-HDMI-SCALER | Specifications | Cypress PCHD-HDMI-SCALER Specifications

CP-293N
PC/HD to HDMI Scaler
Operation Manual
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes no
commitment to update or to keep current the information contained
in this document.
Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer file, in any form or by any means—
electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise—without express written permission and consent from
Cypress Technology.
© Copyright 2011 by Cypress Technology.
All Rights Reserved.
Version 1.1 August 2011
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
•
Always follow basic safety precautions to reduce the risk of fire,
electrical shock and injury to persons.
•
To prevent fire or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
•
Never spill liquid of any kind on or into this product.
•
Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
•
Do not attach the power supply cabling to building surfaces.
•
Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
•
Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
•
To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufficient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO.
DATE DD/MM/YY SUMMARY OF CHANGE
VR0
11/08/14
Preliminary Release
VR1
25/12/14
Add Audio Cable
VR2
13/01/15
D-sub Cable Type
VS3
21/04/15
Updated Text/Diagrams
CONTENTS
1. Introduction�������������������������������������������� 1
2. Applications������������������������������������������� 1
3. Package Contents�������������������������������� 1
4. System Requirements���������������������������� 1
5. Features�������������������������������������������������� 2
6. Operation Controls and Functions������� 3
6.1 Front Panel����������������������������������������3
6.2 Rear Panel�����������������������������������������4
6.3 OSD Menu�����������������������������������������5
7. Connection Diagram���������������������������� 7
8. Specifications���������������������������������������� 8
8.1 Technical Specifications�����������������8
8.2 Input and Output Resolutions���������9
8.3 Audio Specifications����������������������10
9. Acronyms��������������������������������������������� 10
1. INTRODUCTION
The PC to HDMI Scaler is designed to upscale an analog video signal
from a PC (VGA) or HD (Component Video) source device to digital
HDMI output in a wide range of HDTV and PC resolutions up to 1080p/
WUXGA. Additionally this unit can also convert a digital/analog audio
signal and then simultaneously output to an HDMI, Optical and 3.5mm
Mini-jack (L/R audio) connections. This unit has a comprehensive OSD
menu that allows the user to select a variety of output resolutions and
make picture adjustments to optimize the image quality.
2. APPLICATIONS
• Display an analog PC/HD video signal on an HDMI display
• Scale an analog PC/HD video signal to HD resolutions
• Integrate an analog PC/HD video device, such as a Laptop or nonHDMI DVD player to an HDMI equipped display or AV receiver
3. PACKAGE CONTENTS
• 1×PC to HD Scaler
• 1×VGA Cable (D-sub 15-pin to D-sub 15-pin)
• 1×Stereo Audio Cable (3.5mm to 2-RCA)
• 1×5 V/2.6 A DC Power Adaptor
• Operation Manual
4. SYSTEM REQUIREMENTS
Analog video source equipment such as a non-HDMI equipped DVD
player or PC/Laptop and and HDMI equipped display or switching
device such as a matrix or AV receiver.
1
5. FEATURES
• HDMI, HDCP and DVI compliant
• Supports a wide range of PC resolutions from VGA to WUXGA (RB)
and HD resolutions from 480i to 1080p
• Automatically detects the display settings of the connected display
and outputs the correct resolution and refresh rate when the NATIVE
output option is selected
• Supports adjustment of contrast, brightness, hue, saturation,
sharpness, RGB (color tone) level and aspect ratio size of the video
output
• Supports OSD selectable stereo analog and digital audio inputs
and simultaneous stereo analog and digital audio outputs to HDMI,
Optical digital audio and analog mini-jack connections
2
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
1 HDMI OUTPUT: Connect to a HDMI equipped display or AV receiver
for video and audio output.
2 OPTICAL OUTPUT: Connect to an amplifier or active speakers with
an optical cable for LPCM 2 channel digital audio output.
3 AUDIO OUTPUT: Connect to an amplifier or active speakers with a
3.5mm mini-jack cable for analog audio output.
4 MENU Button: Press this button to enter the OSD (On-Screen
Display) menu and press it again to make a selection.
5 +/− Button: Press these buttons to:
When in the OSD menu
• Navigate up/down the OSD menu.
• To adjust the value of a menu selection.
Under normal operation (outside of OSD menu)
• Press the '-' button to perform automatic calibration of the
output signal when in PC MODE only.
• Press the '+' button together with the 'MENU' button to switch the
output resolution to XGA@60 (1024×768).
• Press the '-' button together with 'MENU' button to switch the
output resolution to 720p@60.
• Press both the '+' and '-' buttons at the same time to reset the
device to the default settings.
3
6.2 Rear Panel
1 PC INPUT: Connect to the D-sub/VGA output of a source device
such as a PC/Laptop with D-sub 15-pin cable or a DVD player with
the supplied D-sub 15-pin to D-sub 15-pin adaptor cable.
2 AUDIO INPUT: Connect to the analog audio output of the source
device such as a PC/Laptop with a 3.5mm mini-jack cable.
3 OPTICAL INPUT: Connect to the optical digital audio output of the
source device with an optical cable.
4 SERV.: Reserved for firmware update only
5 DC 5V: Connect the 5V DC power supply to the unit and plug the
adaptor into an AC outlet.
6 Power LED: This LED will illuminate once the unit is connected to an
active power supply.
4
6.3 OSD Menu
MAIN MENU
1ST LAYER
2ND LAYER
PICTURE
CONTRAST
0~100 (50)
SETTING
BRIGHTNESS
0~100 (50)
EXIT
FINETUNE
PHASE
0~100 (100)
(PC Mode
CLOCK
0~100 (50)
H-POSITION
0~100 (50)
V-POSITION
0~100 (50)
Only)
EXIT
FINETUNE
HUE
0~100 (50)
(HD/SD Mode
SATURATION
0~100 (50)
SHARPNESS
0~100 (50)
NR
OFF, LOW, MIDDLE, HIGH (OFF)
Only)
EXIT
COLOR
RED
0~100 (50)
SETTING
GREEN
0~100 (50)
BLUE
0~100 (50)
EXIT
5
MAIN MENU
1ST LAYER
2ND LAYER
OUTPUT
SIZE
FULL, OVERSCAN, UNDERSCAN,
SETTING
LETTER BOX, PANSCAN, ASPECT
(FULL)
RESOLUTION
640×480@60, 800×600@60,
1024×768@60, 1280×1024@60,
1400×150@60, 1600×1200@60,
1280×800@60, 1440×900@60,
1680×1050@60,
1920×1200@60RB, 1600×900@60,
480p, 720p@60, 1080i@60,
1080p@60, 576p, 720p@50,
1080i@50, 1080p@50
EXIT
AUDIO
DELAY
OFF, 40ms, 110ms, 150ms (OFF)
SETTING
INPUT
ANALOG, OPTICAL (ANALOG)
SOUND
ON, MUTE (ON)
EXIT
OSD SETTING
H-POSITION
0~100 (10)
V-POSITION
0~100 (90)
TIMER
0~100 (50)
BACKGROUND
0~100 (50)
DISPLAY
INFO, ON, OFF (INFO)
EXIT
Note: Values in brackets are default for that setting.
6
7. CONNECTION DIAGRAM
PC/Laptop
D-Sub/VGA
Input
Analog Audio
Input
Digital Optical
Audio Input
Power
Supply
HDMI
Output
Digital Optical
Audio Output
HDTV
7
Analog Audio
Output
AV Receiver
8. SPECIFICATIONS
8.1 Technical Specifications
Video Bandwidth
225 MHz/6.75 Gbps
Input Ports
1×D-Sub 15-pin, 1×3.5mm Mini-jack,
Optical (TOSLINK), 1×USB (Service only)
Output Ports
1×HDMI, Optical (TOSLINK), 1×3.5mm Minijack
HDMI Output Resolutions Up to 1080p & WUXGA@60 (RB)
HDMI and Optical Audio Up to 48 kHz
Sampling Rates
Power Supply
5 V/2.6 A DC (US/EU standards, CE/FCC/UL
certified)
ESD Protection
Human body model:
±8 kV (air-gap discharge)
±6 kV (contact discharge)
Dimensions
102 mm (W)×147 mm (D)×25 mm (H)/Jack
Excluded
102 mm (W)×157 mm (D)×25 mm (H)/Jack
Included
Weight
340 g
Chassis Material
Aluminum
Color
Black
Operating Temperature
0 ˚C~40 ˚C/32 ˚F~104 ˚F
Storage Temperature
−20 ˚C~60 ˚C / −4 ˚F~140 ˚F
Relative Humidity
20 ~ 90 % RH (non-condensing)
Power Consumption
4.8 W
8
8.2 Input and Output Resolutions
INPUT
OUTPUT
RESOLUTION
PC
SD/HD
PC
SD/HD
640×480@60/72/75/85

@60
800×600@56/60/72/75/85

@60
1024×768@60/70/75/85

@60
1280×1024@60/75/85

@60
1400×1050@60


1600×1200@60

@60
1280×800@60

@60
1440×900@60


1600×900@60


1680×1050@50/60

@60
1920×1200@60RB


480i/576i

480p/576p


720p@50/60


1080i@50/60


1080p@50/60


9
8.3 Audio Specifications
INPUT LEVEL/
FREQ.
OUTPUT
TERMINAL
OUTPUT
LEVEL
THD+N
FREQUENCE
RESPONSE
SNR
CROSSTALK
Digital
0dB/1kHz
Digital
0dB ~ −1dB
<0.01%
±3dB
>70dB
<-80dB
Analog
1Vrms/1kHz
Digital
0dB ~
−1.5dB
<0.1%
±3dB
>70dB
<−60dB
Digital
0dB/1kHz
Analog
0.5Vrms
±10%
<0.1%
±3dB
±3dB
<−60dB
Analog
1Vrms/1kHz
Analog
0.5Vrms
±10%
<0.1%
±3dB
>70dB
<−60dB
9. ACRONYMS
ACRONYM
COMPLETE TERM
HDMI
High-Definition Multimedia Interface
WUXGA (RB)
Widescreen Ultra Extended Graphics Array
(Reduce blanking)
10
CYPRESS TECHNOLOGY CO., LTD
Home page: http://www.cypress.com.tw
MPM-CP293N
Download PDF