220i cut sheet - Harman Professional

DriveRack 220i
®
®
System Processor with AFS™ Advanced Feedback Suppression
Designed from the ground up to provide state-of-the-art signal processing, the DriveRack 220i
is the perfect tool for any fixed-install application. With a full complement of processing features and Mic/Line inputs the DriveRack 220i can provide both system and microphone processing. Featuring the new, patent-pending Advanced Feedback Suppression (AFS) algorithm,
equalization, dynamics processing, delay, matrix mixing, and bandpass filters, the DriveRack
220i will exceed your expectations.
The DriveRack 220i is piloted from the intuitive DriveWare GUI that offers both Configuration
and Control of the processing modules. Modules can be accessed, edited and saved as part
of programs. Processing modules can be linked between the channels for true stereo processing. If independent processing is desired, parameters can be copied from one channel to
the next to ensure that setup is quick and easy. Stored programs can be loaded from either
the front panel or from wall mounted Zone Controllers. Zone Controllers can also be used for
output muting or adjusting output volumes. For more information please visit www.driverack.com or www.dbxpro.com.
• Advanced Feedback
Suppression (AFS™)
• Graphic and Parametric EQ
• Compressor
• Limiter
• Auto Gain Control
• Noise Gating
• De-Esser
• Ducker
•
•
•
•
•
•
•
Bandpass Filters
Matrix Mixer
1.3 Seconds of Delay
RS-232 PC GUI control
Mic/Line Inputs
Wall Panel Control
Security Lockout
8760 S. Sandy Pkwy.
Sandy, Utah 84070
Phone (801) 568-7660
Fax (801) 568-7662
Int’l Fax (801) 568-7583
customer@dbxpro.com
http://www.dbxpro.com
A Harman International Company
18-0245 -A 9/03
®
DriveRack 220i
System Processor with AFS™ Advanced Feedback Suppression
Analog Inputs:
D/A Performance:
Number of Inputs:
Connectors:
Type:
(2) Switchable line or mic inputs
Female XLR line inputs and Euroblock
Electronically balanced/RF filtered
Impedance:
Max input line level:
CMRR:
Mic Pre gain:
Mic EIN:
Mic Phantom Power:
> 50k Ω
+20dBu
> 40dB, typically >55db @ 1kHz
30 to 60dB
< 110dB, 22Hz-22kHz, 150Ω
15V
Analog Outputs:
Number of Outputs:
Connectors:
Type:
Impedance:
Max Output Level:
(2)
Male XLR and Euroblock
Electronically balanced, RF filtered
120 Ω balanced, 60Ω unbalanced
+20dBu
Dynamic Range:
112 dB A-weighted, 109dB unweighted
System Performance:
Dynamic Range:
THD+N:
Frequency Response:
Interchannel Crosstalk:
Crosstalk input to output:
Operating voltage:
Size:
>110 dB A-weighted, >107dB unweighted,
0.003% typical at +4dBu, 1kHz, 0dB gain
20Hz – 20kHz, +/- 0.5dB
>110dB, 120dB typical
>80dB
100 VAC, 50/60Hz, 120 VAC, 60Hz, 230VAC 50/60Hz
19” Wide, 1.75”High, 7.7” Deep
Safety Agency Approvals:
UL 6500, IEC 60065, EN 55013, E 60065
A/D Performance:
Type:
Dynamic Range line:
Type IV dynamic range:
Sample Rate:
dbx Type IV™ conversion system
>113 dB A-weighted, >110 dB unweighted
>119 dB, A-weighted, 22kHz BW
>117 dB, unweighted, 22kHz BW
48kHz
Architects’ and Engineers’ Specifications:
The device shall provide two balanced inputs which are selectable as line level or mic level with phantom power. The line inputs and output gains shall be controllable
via software; the mic inputs shall be adjustable from the rear panel. Analog audio inputs and outputs shall be accessible via rear panel XLR and Euroblock connectors.
The signal processing Graphic User Interface (GUI) software shall be user programmable using Windows® 98, 2000, and XP operating systems. Software control shall be
via RS-232 protocol and shall be located on both the front and rear panel. The GUI shall provide display, configuration and control of all signal processing functions
including, but not limited to: • Input Gain and Mixing • Graphic or Parametric Equalization • Compression • Limiting • Gating • Automatic Gain Control • Ducking •
De-Essing • Advanced Feedback Suppression (AFS™) • Notch Filters • Sub-Harmonic Synthesis • Matrix Mixing • Bandpass Filtering • Delay
Front panel controls shall include program selection and load buttons. Clearing feedback suppression filters shall also be provided for using the program up and program down buttons. A PC connection and Clip indicator shall be located on the front panel. The front panel shall also include input and output level meters with a 6segment LED meter and output dynamics threshold LED.
External control shall include program selection, output level control and muting, and shall be via industry-standard CAT5 cable with RJ45 connectors. The device shall
include 20 internal programs with up to 10 being user configurable. All program memory shall be non-volatile providing program security should power or computer
fail.
Audio conversion shall be 24-bit 48 kHz. The dynamic range of the processor shall not be lower than 110 dB A-weighted.
The device shall have an IEC power socket. The unit shall meet UL/CSA and CE safety requirements. The unit shall be constructed of cold-rolled steel with a brushed
and anodized aluminum front panel, and mount into a standard 19” 1U EIA rack. The device shall be a dbx DriveRack® 220i.
FOR MORE INFORMATION CONTACT:
dbx Professional Products
8760 S. Sandy Pkwy.
Sandy, Utah 84070
Phone (801) 568-7660
Fax (801) 568-7662
The Professional’s Choice In Signal Processing™
A Harman International Company
customer@dbxpro.com
http://www.dbxpro.com