Elo TouchSystems | 1529L | User guide | Elo TouchSystems 1529L User guide

* Shown with optional peripherals
Touchmonitor User Guide
1529L 15” LCD Desktop Touchmonitor, 3000 series
(Optional Magnetic Stripe Reader, Barcode Scanner,
Customer Display and Biometric available)
Elo Touchmonitor
User Guide
15" LCD Desktop
1529L
Revision F
P/N 008603E
Elo TouchSystems.
1-800-ELOTOUCH
www.elotouch.com
Copyright © 2008 Tyco Electronics. All Rights Reserved.
No part of this publication may be reproduced, transmitted, transcribed, stored in a
retrieval system, or translated into any language or computer language, in any form or by
any means, including, but not limited to, electronic, magnetic, optical, chemical, manual,
or otherwise without prior written permission of Elo TouchSystems.
Disclaimer
The information in this document is subject to change without notice. Elo TouchSystems
makes no representations or warranties with respect to the contents hereof, and specifically disclaims any implied warranties of merchantability or fitness for a particular purpose.
Elo TouchSystems reserves the right to revise this publication and to make changes from
time to time in the content hereof without obligation of Elo TouchSystems to notify any
person of such revisions or changes.
Trademark Acknowledgments
IntelliTouch, SecureTouch, AccuTouch, and MonitorMouse are trademarks of Elo
TouchSystems.
Other product names mentioned herein may be trademarks or registered trademarks of
their respective companies. Elo TouchSystems claims no interest in trademarks other
than its own.
Table of Contents
Chapter 1
Introduction
1
Product Description ................................................. 1
Detailed LCD Display Performance
Requirements .......................................................... 2
Customer Display .............................................. 3
Serial Version ................................................. 3
Fingerprint Reader ............................................ 3
Theory of Operation ....................................... 4
Sensor Specifications ..................................... 4
Credit Card Reader ........................................... 4
Barcode Scanner .............................................. 4
Omni-directional scanner ................................ 4
Single scanner ................................................ 5
Six Port USB Hub ............................................. 5
External 12 VDC Power Supply ........................ 5
Chapter 2
Installation and Setup
7
Unpacking Your Touchmonitor. ............................... 7
Product Overview .................................................... 8
Main Unit ........................................................... 8
Rear View .......................................................... 8
Side View .......................................................... 9
Base Bottom View ............................................. 9
Kensington™ Lock ............................................ 10
USB Interference Connection ................................. 11
Remove the back cover .................................... 11
Replace the cable cover .................................... 16
USB/Serial Interference Connection ....................... 17
Remove the back cover .................................... 17
Replace the cable cover .................................... 23
Optimizing the LCD Display .................................... 24
Installing the Peripheral Device Drivers .................. 24
Finger Print Reader ........................................... 24
Magnetic Stripe Reader .................................... 25
Testing the USB MSR Keyboard Emulation ... 25
Testing the USB-HID Class MSR .................... 25
Convert MSR from HID to Keyboard
emulation ........................................................ 25
Convert MSR from Keyboard emulation to
HID ................................................................. 26
Rear Facing Customer Display ......................... 26
Barcode Scanner .............................................. 27
Installing the Touch Driver Software ....................... 29
Installing the USB Touch Driver ........................ 30
Installing the USB Touch Driver for Windows
XP, Windows 2000, Me, 98 .............................. 30
Chapter 3
Operation
About Touchmonitor Adjustments .......................
15” LCD Function Key .........................................
Controls and Adjustment ...............................
OSD Lock/Unlock .......................................
Power Lock/Unlock ....................................
OSD Menu Functions .................................
OSD Control Options .................................
Brightness ..................................................
Contrast ......................................................
Saturation, Hue, Flesh Tones .....................
Phase .........................................................
Auto Adjust .................................................
OSD Left/Right ...........................................
OSD Up/Down ............................................
Clock ..........................................................
Color Temperature .....................................
Current Input ..............................................
OSD Position ..............................................
Language ...................................................
Recall Defaults ...........................................
Input Timeout .............................................
Power-Save (No Input) ..............................
Power LED Display & Power Saving .............
General Power Saving Mode .....................
Display Angle ......................................................
Controls and Adjustment .....................................
OSD Lock/Unlock ..........................................
Power Lock/Unlock .......................................
OSD Menu Functions ....................................
OSD Control Options ....................................
Brightness ..................................................
Contrast ......................................................
Saturation, Hue, Flesh Tones .....................
Phase .........................................................
Auto Adjust .................................................
OSD Left/Right ...........................................
OSD Up/Down ............................................
Clock ..........................................................
Color Temperature .....................................
Current Input ..............................................
OSD Position ..............................................
Language ...................................................
Recall Defaults ...........................................
OSD Timeout ..............................................
Input Video Select ......................................
Volume .......................................................
31
32
33
33
33
33
34
34
34
34
34
34
34
34
34
34
34
34
35
35
35
35
35
35
35
37
37
37
37
38
38
38
38
38
38
38
38
38
38
38
38
38
39
39
39
39
Chapter 4
Troubleshooting
41
Solutions to Common Problems ......................... 41
31
Appendix A
Native Resolution
43
Appendix B
Touchmonitor Safety
45
Care and Handling of Your Touchmonitor ........... 46
Appendix C
Technical Specifications
Touchmonitor Specifications .........................
AccuTouch Touchscreen
Specifications ................................................
IntelliTouch Touchscreen
Specifications ................................................
Infrared Touchscreen
Specifications ................................................
Acoustic Pulse Recognition
Specifications ................................................
15” LCD Touchmonitor
(1529L-XXXA-1-XX-G) Dimension ................
15” LCD Touchmonitor
(1529L-XXXA-1-XX-T-G) Dimension ............
47
48
49
50
51
52
53
53
Regulatory Information
55
Warranty
59
Index
62
C H A P T E R
1
INTRODUCTION
Product Description
The 1529L is a retail terminal designed to present information to the operator and the
customer. The 1529L is available in serial and USB versions or combo touch monitor.
The 1529L consists of a 15.0” LCD main display with a touchscreen and the following
optional peripherals: customer display, vacuum fluorescent display (VFD) Customer
Display, fingerprint reader, barcode scanner, credit card reader, and a 6 port USB (USB
version only) Hub. The main display element is a 15.0 inch diagonal XGA resolution
(1024 x 768) LCD display. The main display will consist of an LCD Display and
touchscreen. Four types of touchscreens can be selected in the 1529L as options. They
are AccuTouch, Intellitouch, and carrollTouch and Acoustic Pulse Recognition.
The fingerprint reader translates illuminated images of fingerprints into digital code for
further software processing, e.g. enrollment (fingerprint registration) and verification
(authentication of registered users). The fingerprint reader uses the SEIR method and
CMOS image sensor to capture high contrast, high resolution fingerprint images. A series of algorithms extracts minutiae data from the image, mapping the distinguishing
characteristics of fingerprint ridge ends, splits, dots, and arches. To identify or verify a
fingerprint, a proprietary matching algorithm compares the extracted minutiae points
from the input fingerprint on the optical module to a previously stored sample. The
entire matching process takes roughly one second. There is a fingerprint reader available in the USB version of the 1529L.
1-1
The credit card reader reads all three stripes on a standard credit card or drivers license.
The credit card is read by sliding the credit card, stripe side toward the display through
the credit card reader forward or backward. There is a USB credit card reader only.
The Hub provides 4 internal USB ports to be used by the credit card reader, the fingerprint reader or barcode scanner, the touchscreen, and the customer display. The hub also
supplies two USB ports to the outside of the back of the 1529L for external use. The hub
is only used by the USB version of the 1529L. The 1529L is powered by a universal AC
power source or 12 VDC from external power source.
The barcode scanner comes in two different configurations. The first is a high-end
omni-directional scanner, which is also capable of reading 2-D barcodes. And the second is a lower cost, yet efficient, 1-D scanner. Both scanners run on a USB interface.
Detailed LCD Display Performance Requirements
15 inch TFT LCD Display Panel
Display Format
Display area 15”
1024 x 768
304.1mm(H) x 228mm(V)
Pixel Pitch 15”
Contrast Ratio
0.297mm(H) x 0.297mm(V)
400:1 typical
Brightness
LCD
350 cd/m2 (Typical)
AccuTouch
IntelliTouch
280 cd/m2 (Typical)
322 cd/m2 (Typical)
CarrollTouch
Surface Capacitive
322 cd/m2 (Typical)
298 cd/m2 (Typical)
Acoustic Pulse Recognition
Accutouch Transmission
322 cd/m2 (Typical)
82% typical
IntelliTouch Transmission
IR Touchscreen Transmission
92% typical
92% typical
Surface Capacitive Transmission
Acoustic Pulse Recognition
84% typical
92% typical
Response Time
Display Color
Tr=4 msec/Tf=12msec typical
16.2 million colors, 6 Bit with dithering
Vertical Viewing Angle
Typical Vertical Viewing Angle: 60deg(looking down)/40 deg(lookingup)
@ CR>=10
Horizontal Viewing Angle
Typical Vertical Viewing Angle: 60deg(looking down)/60 deg(lookingup)
@ CR>=10
1-2 Elo Touchmonitor User Guide
Customer Display
The Customer Display is a twenty character two line vacuum fluorescent display (VFD).
It consists of a VFD and VFD controller.
Serial Version
Optional Parameters
Characters per row
Number of rows
Character
configuration
Character Height
Character width
Character
configuration
Character color
MTBF
20
2
5x7 dot matrix
9.5mm
6.2mm
ASCII
Blue green
300,000 hours
Fingerprint Reader
There is a fingerprint reader in the USB version only.
General Description-FDU01B is a PC peripheral FRD (Fingerprint Recognition Device)
for USB (Universal Serial Bus) connections.
1-3
Specifications
Sensor
Image Capture Speed
Image Transfer Speed
Pixel Resolution
USB Signaling Type
SecuGen FOR
600ms/frame
500Byte/ms
356x292
Full Speed Type
Theory of Operation
The USB host initiates communication with the FDU01 using operation commands
(Sensor LED On, Fingerprint Capture Start and Stop). Fingerprint data are then captured by the CMOS sensor at a total image size of 356 x 292 with 8-bit gray level. The
image frame transfer speed is 500 bytes/ms. It takes about 600 milliseconds to send one
frame of image data over USB protocols. FDU01 uses the SecuGen FOR (Fingerprint
Optic Reader).
Sensor Specifications
Sensor
Resolution
Verifying Time
Image Capture Error Rate
Life Time Typically
CMOS Image Sensor
500dpi
<1sec
<0.1%
40,000Hrs
Credit Card Reader
There is a USB credit card reader only. The USB version is available in HID and Keyboard emulation versions. The reader reads all three stripes on a standard credit card or
drivers license.
Reference Standards-Conform to
applicable standards
Message Format
Card Speed
MTBF Electronics
International Standards Organization, American National Standards
Institute, California Drivers License, American Association of Motor
Vehicle Administrators
ACCII
3 to 50 IPS
125,000 hrs; Head 1,000,000 passes
Barcode Scanner
Omni-directional scanner:
1. Ability to read 1D codes with a 360º rotation, eliminating the need to orient the
scanner in the field of view
2. Scan angle
Minimum horizontal: 34º ± 1.5º
Minimum vertical: 12.5º ± 1.5º
3. Ability to read 2-D barcodes (PDF417, Micro PDF)
4. Ability to read damaged or poorly printed barcodes
1-4 Elo Touchmonitor User Guide
5. Effective form factor; ability to be mounted on side of ET1529L
6. USB interface that complies with USB 2.0 standards
7. USB bus powered
8. Easy communication between host and scanner
9. Visible laser diode operating at 650nm
10.600+ scans/sec
1-D scanner:
1. Ability to read 1-D codes
2. Scan angle
Minimum: 47º ± 3º
3. Low cost solution
4. Effective form factor; ability to be mounted on side of ET1529L
5. USB interface that complies with USB 2.0 standards
6. USB bus powered
7. Easy communication between host and scanner
8. Visible laser diode operating at 650nm
9. 100+ scans/sec
Six Port USB Hub
The Hub provides 4 internal USB ports to be used by the credit card reader, the fingerprint reader, the touchscreen, and the customer display. The hub also supplies two USB
ports to the outside of the back of the 1529L for external use. The hub is only used by the
USB version of the 1529L. The hub meets the following requirements:
Specification
Full compliance with USB specification 1.0, 1.1 and HID Class Definition Rev 1.0.
Hub shall be self powered
Hub shall provide 2 external and 4 internal downstream ports with individual port over
current detection, protection and recovery. Supports both Open Host Controller Interface (OHCI) and Universal Host Controller Interface (UHCI).
Supports Suspend and Resume operation.
Bus fault detection and recovery.
External Power Supply
The 1529L shall be powered by a universal AC power source or 12 VDC from external
power source. The power supply shall provide the following capability:
AC power: Input voltage 85 to 265 vac
Input frequency 47 to 63hz
DC power: Input voltage 12 vdc
Input line and load regulation +/-2%
1-5
1-6 Elo Touchmonitor User Guide
C H A P T E R
2
INSTALLATION AND SETUP
This chapter discusses how to install your LCD touchmonitor and how to install Elo
TouchSystems driver software.
Unpacking Your Touchmonitor
Check that the following items are present and in good condition:
Touchmonitor
Power cable US/Candian
DVI cable
USB Cable
Video cable
European power cable
Speaker
CD and Quick Install Guide
2-7
Product Overview
Main Unit
Note: Shown with optional Biometric & MSR.
Rear View
Note: Shown with optional Rear Facing Customer Display.
2-8 Elo Touchmonitor User Guide
Side View
Base Bottom View
or
2-9
Kensington
TM
Lock
The KensingtonTM lock is a security device that prevents theft. To
find out more about this security device, do to http://www.
kensington.com.
2-10 Elo Touchmonitor User Guide
USB Interface Connection
Your touchmonitor comes with only one touchscreen connector cables: USB cable. (For
Windows 2000, Me and XP systems only.)
To set up the display, please refer to the following figures and procedures:
Remove the Cable Cover
The cables are connected at the back of the monitor.
cable cover
To remove the cover, grasp the lip of the cover and pull towards you until it snaps off.
2-11
CAUTION
Before connecting the cables to your touchmonitor and PC, be sure that the
computer and touchmonitor are turned off.
NOTE
Before connecting the cables to the touchmonitor, route all the cables through
the hole in the second as shown in the picture above.
2-12 Elo Touchmonitor User Guide
The following illustrations guide you step by step in connecting your touchmonitor
using a USB cable connection.
Power cord
Connect one end of the power cord to the monitor and the other end to wall.
Connect the power cable to the power port in the monitor.
2-13
Video cable
Connect one end of the video cable to the rear side of computer and the other to the
LCD. Tighten by turning the two thumb screws clockwise to ensure proper grounding.
You can select DVI video cable or D-SUB15 video cable.
DVI cable
2-14 Elo Touchmonitor User Guide
Speaker cable
Connect one end of the speaker cable to the speaker port in the computer and the other
end to the port in the monitor.
2-15
USB cable
Connect one end of the USB cable to the rear side of the computer and the other to the
LCD monitor.
The USB cable is for optional touch, MSR, CD and Finger Print Reader. Only one USB
cable is needed because the device contains a self powered USB 1.1 Hub. Two self
powered ports are available for running other USB devices. For touch only, no USB
Hub is present.
2-16 Elo Touchmonitor User Guide
USB / SERIAL Interface Connection
Your touchmonitor comes with only one touchscreen connector cables: USB cable. (For
Windows 2000, Me and XP systems only.)
To set up the display, please refer to the following figures and procedures:
Remove the Cable Cover
The cables are connected at the back of the monitor.
cable cover
To remove the cover, grasp the lip of the cover and pull towards you until it snaps off.
2-17
CAUTION
Before connecting the cables to your touchmonitor and PC, be sure that the
computer and touchmonitor are turned off.
NOTE
Before connecting the cables to the touchmonitor, route all the cables through
the hole in the second as shown in the picture above.
2-18 Elo Touchmonitor User Guide
The following illustrations guide you step by step in connecting your touchmonitor
using a USB cable connection.
Power cord
Connect one end of the power cord to the monitor and the other end to wall.
Connect the power cable to the power port in the monitor.
2-19
Video cable
Connect one end of the video cable to the rear side of computer and the other to the
LCD. Tighten by turning the two thumb screws clockwise to ensure proper grounding.
You can select DVI video cable or D-SUB15 video cable.
DVI cable
2-20 Elo Touchmonitor User Guide
Speaker cable
Connect one end of the speaker cable to the speaker port in the computer and the other
end to the port in the monitor.
2-21
USB cable
Serial cable
For USB interface, connect one end of the USB cable to the rear side of the computer
and the other to the LCD monitor.
For Serial interface, connect one end of the RS-232 cable to the rear side of the conputer
and the other to the LCD monitor.
2-22 Elo Touchmonitor User Guide
Replace the Cable Cover
Cable cover lip
cables
Then you have attached all the cables to the monitor, gently bring all the cables toward
the standard so they fit under the cover lip.
Snap the Cable cover in place over the connections.
2-23
Optimizing the LCD Display
To ensure the LCD display works well with your computer, configure the display mode
of your graphic card to make it less than or equal to 1024 x 768 resolution, and make
sure the timing of the display mode is compatible with the LCD display. Refer to Appendix A for more information about resolution. Compatible video modes for your
touchmonitor are listed in Appendix C.
Installing the Peripheral Device Drivers
Finger Print Reader
NOTE:
This driver is for MS Windows 9x through XP.
1
2
On the TouchTools CD, browse to Touch Monitor Peripherals\Finger
Print Readers\Fingerprint Reader 229L 1529L\Driver Install\Drivers.
Double-click setup.exe
Follow the Install Shield Wizard procedure to complete the installation.
For a detailed software development kit, browse to Touch Monitor
Peripherals\Finger Print Readers\Fingerprint Reader 229L 1529L\Driver
Install\Drivers and open the following files:
• FDxSDKforWindows1 .20.zip
• SecuBSPSDK for Windows2 .10.zip
You will enter one of the following serial numbers depending on your operating system:
• FDx SDK for Windows: 31-100s101-3586383
• FDx SDK for Windows CE: 32-100s101-9713291
• SecuBSP SDK for Windows: 41-100s101-7685871
• SecuBSP SDK for Windows CE: 42-100s101-1155462
• SecuBSP SDK: 51-100s101-5963137
Once the driver setup is complete, the demo program can be run from Touch Monitor
Peripherals\Finger Print Readers\Fingerprint Reader 229L 1529L\Demo\
BSPDemo.exe
2-24 Elo Touchmonitor User Guide
Magnetic Stripe Reader
No device are needed.
Testing the USB MSR Keyboard Emulation
1 Plug in the device.
2 Open MS Word.
3 Slide the card through the MSR to view the data.
Testing the USB-HID Class MSR
1 On the CD, browse to Touch Monitor Peripherals\Magnetic Stripe Card
Readers\Demo.
2 Open the Readme.txt and follow instructions to test the unit.
Convert MSR from HID to keyboard Emulation
1 To convert from HID mode to Keyboard Emulation mode
1.1 Double-click on the “MSR Change Mode” icon on the desktop.
The following will appear:
1.2
The dim box will indicate the current setting. Click the “Keyboard Mode”
to switch to Keyboard Emulation mode.
1.3 Click “Quit” to close the window.
2 Open NotedPad.
3 Slide the card through the MSR to view the data.
2-25
Convert MSR from keyboard emulation to HID
1 To convert from Keyboard Emulation mode to HID mode
1.1 Double-click on the “MSR Change Mode” icon on the desktop.
The following will appear:
1.2 The dim box will indicate the current setting. Click the “HID Mode” to
switch to HID mode.
1.3 Click “Quit” to close the window.
Rear Facing Customer Display
1. Insert your Elo TouchTools CD.
2. On the CD, browse to Touch Monitor Peripherals\Rear Facing Customer
Display\Drivers\USB Drivers. Click on the folder that has the name of your
operating system for the necessary drivers.
3. Once in this folder, open up the zip file and open the install text file for further driver
installation instructions.
* Note: If your software requires OPOS Drivers, it is available in the following location:
Touch Monitor Peripherals\Rear Facing Customer Display\Drivers\OPOS Drivers.
Test Applications:
1. Insert your Elo TouchTools CD.
2. On the CD, browse to Touch Monitor Peripherals\Rear Facing Customer
Display\Testing\USB.
3. Open up the text file named USB Test and follow the instructions. This testing
procedure assumes you have already installed the necessary USB drivers.
2-26 Elo Touchmonitor User Guide
Barcode Scanner
1.
2.
3.
4.
Insert your Elo TouchTools CD.
On the CD, browse to Touch Monitor Peripherals\Barcode Scanner Startup\Drivers.
Double-click on USB7210.msi and follow the prompts given by the setup file.
Once you have finished installing the above: Right click on My Computer and
click on Properties. Click on the Hardware tab and then click Device Manager.
5. Double click on USB7210 Converter Module, which should be located in the
Other Devices section. Next click on Reinstall Driver.
6. Now your Windows operating system should guide you through the rest of the
installation process. If any files are requested, please provide the following pathname
in your Elo TouchTools CD: Touch Monitor Peripherals\Barcode Scanner
Startup\Drivers.
Test Applications:
1.
2.
3.
Insert your Elo TouchTools CD.
On the CD, browse to Touch Monitor Peripherals\Barcode Scanner Startup\Test
Applications.
Double click on Scanner Test Application Readme. This document will explain
how to test your scanner for basic functionality.
Your scanner default settings do not enable 2-D barcode reading ability. In order to
enable this option, follow these steps:
1) Scan the barcodes below to enable PDF417 and MicroPDF417. These are
both types of 2-D barcodes.
2-27
2) Now scan the barcode below to change your scanning pattern. Using this
scanning pattern will allow you to read 2-D barcodes (you can still read 1-D
barcodes also).
The scanner module also adds a Hall Effect Switch (HE Switch) that enables the unit to
automatically set the Trigger mode of the Scan Engine depending on the location of an
external magnet (included in scanner cradle).
The output of the HE Switch switches low (turns ON) when a magnetic field (south
polarity) perpendicular to the Hall sensor exceeds the operate point threshold, BOP
(typically 100 G magnetic field). When the magnetic field is reduced below the release
point, BRP, (typically 45 G magnetic field) the HE Switch output goes high (turns OFF).
The Hall Effect Switch goes to the USB Controller’s DSR input. As the HE Switch
opens or closes, it causes the USB Controller to initiate a USB Interrupt message to the
host. When the Host Application software detects the DSR input active LOW via the
USB Interrupt and a CDC message (HE Switch is ON), it sends a ‘Continuous Trigger’
SSI command to the Symbol Scan Engine.
The Scan Engine turns on the laser and is able to scan and decode barcodes continuously
without the user having to press the trigger (momentary switch). When the Host Application software detects the DSR input HIGH (HE Switch is OFF), it sends a ‘Level
Trigger’ SSI command to the Symbol Scan Engine. The Scan Engine turns off the laser
and will scan and decode barcodes only when the trigger is activated.
2-28 Elo Touchmonitor User Guide
Installing the Touch Driver Software
Elo TouchSystems provides driver software that allows your touchmonitor to work with
your computer. Drivers are located on the enclosed CD-ROM for the following operating systems:
• Windows XP
• Windows 2000
• Windows Me
• Windows 98
• Windows 95
• Windows NT 4.0
• CE 2.x, 3.0, 4x
• Windows XP Embedded
• Windows 3.x
• MS DOS
• OS/2
Additional drivers and driver information for other operating systems (including
Macintosh and Linux) are available on the Elo TouchSystems web site at www.elotouch.
com.
Your Elo USB touchmonitor is plug-and-play compliant. Information on the video capabilities of your touchmonitor is sent to your video display adapter when Windows starts.
If Windows detects your touchmonitor, follow the instructions on the screen to install a
generic plug-and-play monitor.
Refer to the appropriate following section for driver installation instructions.
2-29
Installing the USB Touch Driver
Installing the USB Touch Driver for Windows XP, Windows 2000,
Me and 98
1 Insert the Elo CD-ROM in your computer’s CD-ROM drive.
If Windows XP, Windows 2000,Windows 98, or Windows Me starts the Add New
Hardware Wizard:
2 Choose Next. Select “Search for the best driver for your device (Recommended)” and
choose Next.
3 When a list of search locations is displayed, place a checkmark on “Specify a
location” and use Browse to select the \EloUSB directory on the Elo CD-ROM.
4 Choose Next. Once the Elo TouchSystems USB touchscreen driver has been detected,
choose Next again.
5 You will see several files being copied. Insert your Windows 98 CD if prompted.
Choose Finish.
If Windows XP, Windows 2000,Windows 98, or Windows Me does not start the Add
New Hardware Wizard:
NOTE:
For Windows XP and Windows 2000 you must have administrator access
rights to install the driver.
1 Insert the Elo CD-ROM in your computer’s CD-ROM drive. If the AutoStart feature
for your CD-ROM drive is active, the system automatically detects the CD and starts
the setup program.
2 Follow the directions on the screen to complete the driver setup for your
version of Windows. If the AutoStart feature is not active:
1 Click Start > Run.
2 Click the Browse button to locate the EloCd.exe program on the CD-ROM.
3 Click Open, then OK to run EloCd.exe.
4 Follow the directions on the screen to complete the driver setup for your
version of Windows.
2-30
Elo Touchmonitor User Guide
C H A P T E R
3
OPERATION
About Touchmonitor Adjustments
Your touchmonitor will unlikely require adjustment. Variations in video output and application may require adjustments to your touchmonitor to optimize the quality of the
display.
For best performance, your touchmonitor should be operating in native resolution, that
is 1024 x 768 at 60-75 Hz. Use the Display control panel in Windows to choose 1024 x
768 resolution.
Operating in other resolutions will degrade video performance. For further information,
please refer to Appendix A.
All adjustments you make to the controls are automatically memorized. This feature
saves you from having to reset your choices every time you unplug or power your
touchmonitor off and on. If there is a power failure your touchmonitor settings will not
default to the factory specifications.
To restore factory set up, choose it from the OSD. See page 3-43.
3-31
15” LCD Function Key
5
4
3
2
1
1
Controls
Power Switch
Function
Turns the display system power on or off.
2
Select
Displays the OSD menus on the screen and used to
select (“Clockwise” and “Counter-clockwise” direction) the OSD control options
3
on the screen.
Adjusts the decreasing value of the selected
4
OSD control option.
Adjusts the increasing value of the selected OSD control option.
5
Menu
Menu display and menu exit.
3-32 Elo Touchmonitor User Guide
Controls and Adjustment
OSD Lock/Unlock
You are able to lock and unlock the OSD feature. The monitor is shipped in the unlocked
position.
To lock the OSD:
1 Press the Menu button and button simultaneously for 2 seconds. A window will
appear displaying “OSD Unlock”. Continue to hold the buttons down for another 2
seconds and the window toggles to “OSD Lock”.
Power Lock/Unlock
You are able to lock/unlock the Power feature. The monitor is shipped in the
unlockedposition.To lock the power:
1 Press the Menu button and the
simultaneously for 2 seconds. A window for another
2 seconds and the window toggles to —Power Lock“.
OSD Menu Functions
To display the OSD Menu press the Menu button.
1 Press the button or button to select the different OSD control option.
2 When the function you want to change is displayed, press the Select button.
To adjust the Value of the function:
1 Pressing the
button increases the value of the selected OSD control option.
2 Pressing the button decreases the value of the selected OSD control
option.
After adjusting the values, the monitor will automatically save the changes.
NOTE:
The OSD screen will disappear if no input activities are detected for 45 seconds.
3-33
OSD Control Options
Brightness
• Background Luminance of the LCD panel is adjusted.
Contrast
• Adjusts the contrast or the values of color gain (RED, GREEN or BLUE).
Sharpness
• The sharpness can be adjustable.
Phase
• Adjusts the phase of the dot clock.
Auto Adjust
• Clock system auto adjustment (under 5 seconds).
OSD Left/Right
• The OSD screen is moved vertically right and left.
OSD Up/Down
• The OSD screen is moved vertically up and down.
Clock
• Adjusts the ratio of dividing frequency of the dot clock.
Color Temperature
• Sets R, G, B gain.
Current Input
• The frequency of the horizontal/vertical synchronizing signal under the input
indicated. (This information is under Auto Adjust icon)
OSD Position
• Allows the OSD indication position to be selected.
Language
• Select the language used for the OSD menu from among English, France, Deutsch,
Spanish and Japanese.
Recall Defaults
• All data copy from factory shipment data.
OSD Timeout
• Adjust time for OSD to disappear.
Input Video Select
• Select D-SUB Analog, DVI Digital signal.
Volume
• To increase or decrease the sound level.
3-34 Elo Touchmonitor User Guide
Power-Save (No Input)
• The LCD panel background is cut when there is no signal input (AC line power
consumption of 4w or less).
Power LED Display & Power Saving
General Power Saving Mode
When the power switch are switch on, this LED lights in green.
The LED indicates the different power status with altered LED colors when monitor
operates in different modes (see following table).
Mode
On
Sleep
Off
Power
Consumption
50w max.
4w max.
2w
Indicator
Green
Orange
NO
We recommend switching the monitor off when it is not in use for a long period of time.
Display Angle
For viewing clarity, you can tilt the LCD forward up 67 to 90 degrees.
3-35
CAUTION
In order to protect the LCD, be sure to hold the base when adjusting the LCD,
and take care not to touch the screen.
3-36 Elo Touchmonitor User Guide
Controls and Adjustment
OSD Lock/Unlock
You are able to lock and unlock the OSD feature. The monitor is shipped in the unlocked
position.
To lock the OSD:
1 Press the Menu button and button simultaneously for 2 seconds. A window will
appear displaying “OSD Unlock”. Continue to hold the buttons down for another 2
seconds and the window toggles to “OSD Lock”.
Power Lock/Unlock
You are able to lock/unlock the Power feature. The monitor is shipped in the
unlockedposition.To lock the power:
1 Press the Menu button and the
simultaneously for 2 seconds. A window for another
2 seconds and the window toggles to —Power Lock“.
OSD Menu Functions
To display the OSD Menu press the Menu button.
1 Press the button or button to select the different OSD control option.
2 When the function you want to change is displayed, press the Select button.
To adjust the Value of the function:
1 Pressing the
button increases the value of the selected OSD control option.
2 Pressing the button decreases the value of the selected OSD control
option.
After adjusting the values, the monitor will automatically save the changes.
NOTE:
The OSD screen will disappear if no input activities are detected for 45 seconds.
3-37
OSD Control Options
Brightness
• Background Luminance of the LCD panel is adjusted
Contrast
• Gain of R, G, and B signal is adjusted.
Sharpness
• The sharpness can be adjustable.
Phase
• The phase of the dot clock is adjusted.
Auto Adjust
• Automatically adjusts the systems dot clock(takes approximately 5 seconds).
OSD Left/Right
• The osd screen is moved horizontally left and right.
OSD Up/Down
• The OSD screen is moved vertically up and down.
Clock
• The ratio of dividing frequency of the dot clock is adjusted.
Color Temperature
• Sets the R, G, and B gains.
Current Input
• The frequency of the horizontal/vertical synchronizing signal under the input is
indicated.(These information is under auto Adjust icon)
OSD Position
• The osd indication position can be selected.
Language
• Select the language for the OSD menu from among English, France, Deutsch,
Spanish and Japanese.
3-38 Elo Touchmonitor User Guide
Recall Defaults
• Restore all original factory defaults.
OSD Timeout
• Adjust how long the OSD menu is displayed.
Input Video Select
• Select D-SUB Analog, dvi Digital signal.
Volume
• To increase or decrease the sound level.
3-39
3-40 Elo Touchmonitor User Guide
C H A P T E R
4
TROUBLESHOOTING
If you are experiencing trouble with your touchmonitor, refer to the following table. If
the problem persists, please contact your local dealer or our service center. Elo Technical Support numbers are listed on the last page of this manual.
Solutions to Common Problems
Problem
Suggestion(s)
The monitor does not respond after
Check that the monitor’s Power Switch is on.
you turn on the system.
Turn off the power and check the monitor’s power cord and signal
Characters on the screen are dim
The screen is blank
cable for proper connection.
Refer to the Controls and Adjustments section to adjust the brightness.
During operation, the monitor screen may automatically turn off as a
result of the Power Saving feature. Press any key to see if the screen
reappears.
Refer to the Controls and Adjustments section to adjust the brightness.
OSD or power buttons don’t work
“Out of Range” display
Check to see that they are not locked out. See page 3-33.
check to see of the resolution or vertical frequency of your computer is
higher than that of the LCD display.
Reconfigure the resolution of your computer to make it less than or
equal to 1024x768. 1024x768 is optimal. See Appendix A for more
information on resolution.
Touch doesn’t work
Make sure cable is securely attached at both ends.
4-41
4-42 Elo Touchmonitor User Guide
C H A P T E R
A
NATIVE RESOLUTION
The native resolution of a monitor is the resolution level at which the LCD panel is
designed to perform best. For the Elo LCD touchmonitor, the native resolution is 1024
x 768 for the 15.0 inch size. In almost all cases, screen images look best when viewed at
their native resolution. You can lower the resolution setting of a monitor but not increase
it.
Input Video
15.0" LCD
640 x 480 (VGA)
800 x 600 (SVGA)
Transforms input format to 1024 x 768
Transforms input format to 1024 x 768
1024 x 768(XGA)
Display in Native Resolution
The native resolution of an LCD is the actual number of pixels horizontally in the LCD
by the number of pixels vertically in the LCD. LCD resolution is usually represented by
the following symbols:
VGA
640 x 480
SVGA
XGA
800 x 600
1024 x 768
A-43
As an example, a SVGA resolution LCD panel has 800 pixels horizontally by 600 pixels
vertically. Input video is also represented by the same terms. XGA input video has a
format of 1024 pixels horizontally by 768 pixels vertically. When the input pixels contained in the video input format match the native resolution of the panel, there is a one to
one correspondence of mapping of input video pixels to LCD pixels. As an example, the
pixel in column 45 and row 26 of the input video is in column 45 and row 26 of the
LCD. For the case when the input video is at a lower or higher resolution than the native
resolution of the LCD, the direct correspondence between the video pixels and the LCD
pixels is lost. The LCD controller can compute the correspondence between video pixels and LCD pixels using algorithms contained on its controller. The accuracy of the
algorithms determines the fidelity of conversion of video pixels to LCD pixels. Poor
fidelity conversion can result in artifacts in the LCD displayed image such as varying
width characters.
A-44 Elo Touchmonitor User Guide
C H A P T E R
B
TOUCHMONITOR SAFETY
This manual contains information that is important for the proper setup and maintenance
of your touchmonitor. Before setting up and powering on your new touchmonitor, read
through this manual, especially Chapter 2 (Installation), and Chapter 3 (Operation).
1 To reduce the risk of electric shock, follow all safety notices and never open the
touchmonitor case.
2 Turn off the product before cleaning
3 Your new touchmonitor is equipped with a 3-wire, grounding power cord. The power
cord plug will only fit into a grounded outlet. Do not attempt to fit the plug into an
outlet that has not been configured for this purpose. Do not use a damaged power
cord. Use only the power cord that comes with your Elo TouchSystems Touchmonitor.
Use of an unauthorized power cord may invalidate your warranty.
4 The slots located on the sides and top of the touchmonitor case are for ventilation. Do
not block or insert anything inside the ventilation slots.
5 It is important that your touchmonitor remains dry. Do not pour liquid into or onto
your touchmonitor. If your touchmonitor becomes wet do not attempt to repair it
yourself.
B-45
Care and Handling of Your Touchmonitor
The following tips will help keep your Elo Entuitive touchmonitor functioning at the
optimal level.
• To avoid risk of electric shock, do not disassemble the brick supply or display unit
cabinet. The unit is not user serviceable. Remember to unplug the display unit from
the power outlet before cleaning.
• Do not use alcohol (methyl, ethyl or isopropyl) or any strong dissolvent. Do not use
thinner or benzene, abrasive cleaners or compressed air.
• To clean the display unit cabinet, use a cloth lightly dampened with a mild detergent.
• Avoid getting liquids inside your touchmonitor. If liquid does get inside, have a
qualified service technician check it before you power it on again.
• Do not wipe the screen with a cloth or sponge that could scratch the surface.
• To clean the touchscreen, use window or glass cleaner. Put the cleaner on the rag and
wipe the touchscreen. Never apply the cleaner directly on the touchscreen .
Warning
This product consists of devices that may contain mercury, which must be recycled or
disposed of in accordance with local, state, or federal laws. (Within this system, the
backlight lamps in the monitor display contain mercury.)
Waste Electrical and Electronic Equipment(WEEE) Directive
In the European Union, this label indicates that this product should not be disposes of
with household waste. It should be deposited at an appropriate facility to enable recovery and recycling.
B-46 Elo Touchmonitor User Guide
C H A P T E R
C
TECHNICAL SPECIFICATIONS
Display Modes
Your Elo Entuitive touchmonitor is compatible with the following standard
video modes:
Item
Resolution
Type
H. Scan(KHz)
V. Scan(Hz)
Pol.
1
2
640X350
720X400
VGA
VGA
31.469
31.469
70.087
70.087
+/
-/+
3
4
640X480
640X480
VGA
VESA72
31.469
37.861
59.940
72.809
-/
-/
5
6
640X480
800X600
VESA75
SVGA
37.500
35.156
75.000
56.250
-/
+/+
7
8
800X600
800X600
SVGA
VESA72
37.879
48.077
60.317
72.188
+/+
+/+
9
10
800X600
1024X768
VESA75
XGA
46.875
48.363
75.000
60.004
+/+
-/-
11
12
1024X768
1024X768
XGA
VESA75
56.476
60.023
70.069
75.029
-/+/+
C-47
Touchmonitor Specifications
Model
LCD Display
1529L
15.0” TFT Active Matrix Panel
Display Size
Pixel Pitch
304.1(H) x 228(V) mm
0.297(H) x 0.297(V) mm
Display Mode
VGA 640 x 350 (70 Hz)
VGA 720 x 400 (70 Hz)
VGA 640 x 480 (60 / 72 / 75 Hz)
SVGA 800 x 600 (56 / 60 / 72 / 75Hz)
Native
XGA 1024 x 768 (60 / 70 / 75Hz)
XGA 1024 x 768
Contrast Ratio
Brightness
400 : 1 (typical)
350 cd/m2 with AT 287 cd/m2, IT 322 cd/m2, IR 322 cd/m2,
LCD
SC 294 cd/m2
350 cd/m2 (Typical)
AccuTouch
IntelliTouch
287 cd/m2 (Typical)
322 cd/m2 (Typical)
CarrollTouch
Surface Capacitive
322 cd/m2 (Typical)
294 cd/m2 (Typical)
Acoustic Pulse Recognition
Response Time
322 cd/m2 (Typical)
Tr= 5 msec, Tf= 11 mesc typical(CPT CLAA150XP01P)
Display Color
Tr= 4 msec, Tf= 12 mesc typical(AU G150XG01)
16.2 million color, 6 bit with dithering
Viewing Angle
Input Signal
VGA Analog Video
(L/R)= -60 /+60 (typical), (U/D) -60 /+40 (typical)
R.G.B. Analog 0.7V peak to peak
Sync
DVI Video
TTL Positive or Negative, Composite Sync, Sync on green
Digital TMDS Input
o
o
o
o
Signal Connector
Front Control
15 Pin D-Sub, DVI-D
Power on / off , Menu,
OSD
Contrast, Brightness, H/V-Position, Recall default,
Color Temperature, Volume, Sharpnss,
,
, Select
Phase, Clock OSD H/V position, OSD Time, Auto Adjust,
OSD Language, Input Select
Plug & Play
Touch Panel (optional)
DDC1 / 2B
AccuTouch, IntelliTouch and CarrollTouch, Surface Capacitive,
Power
Acoustic Pulse Recognition
Input: AC 85-265V, 47-63Hz, or DC 12V/4A (max.)
Operating Conditions
Temp
Humidity
o
o
o
o
0 C ~ 40 C (41 F ~ 95 F)
20% ~ 80% (No Condensation)
Dimensions (HxWxD)
Altitude To 12,000 Feet
354 x 301 x 285mm
Weight (Net)
Certifications
20.1lbs., monitor weight 16.2 lbs.
UL, C-UL, FCC-B, CE, Semko, VCCI, MPRII, C-TICK
C-48 Elo Touchmonitor User Guide
AccuTouch Touchscreen Specifications
Mechanical
Construction
Top: Polyester with outside hard-surface coating with clear or
antiglare finish.
Inside: Transparent conductive coating.
Bottom: Glass substrate with uniform resistive coating. Top and
bottom layers separated by Elo-patented separator dots.
Positional Accuracy
Standard deviation of error is less than 0.080 in. (2.03 mm). This
equates to less than ±1%.
Touchpoint Density
Touch Activation Force
More than 100,000 touchpoints/in² (15,500 touchpoints/cm²).
Typically less than 4 ounces (113 grams).
Surface Durability
Meets Taber Abrasion Test (ASTM D1044), CS-10F wheel, 500 g.
Meets pencil hardness 3H.
Expected Life
Performance
AccuTouch technology has been operationally tested to greater than
35 million touches in one location without failure, using a stylus
similar to a finger.
Optical
Light Transmission
(per ASTM D1003)
Typically 85% at 550-nm wavelength (visible light spectrum).
Visual Resolution
All measurements made using USAF 1951 Resolution Chart, under
30 X magnification, with test unit located approximately 1.5 in.
(38 mm) from surface of resolution chart.
Antiglare surface: 6:1 minimum.
Haze (per ASTM D1003)
Gloss (per ASTM D2457)
Antiglare surface: Less than 15%.
Antiglare surface: 90 ± 20 gloss units tested on a hard-coated front
surface.
C-49
IntelliTouch Touchscreen Specifications
Mechanical
Positional Accuracy
Standard deviation of error is less than 0.080 in. (2.03 mm).
Equates to less than ±1%.
Touchpoint Density
Touch Activation Force
More than 100,000 touchpoints/in2 (15,500 touchpoints/cm2).
Typically less than 3 ounces (85 grams).
Surface Durability
Expected Life Performance
Surface durability is that of glass, Mohs’ hardness rating of 7.
No known wear-out mechanism, as there are no layers, coatings,
or moving parts. IntelliTouch technology has been operationally
tested to more than 50 million touches in one location without
Sealing
failure, using a stylus similar to a finger.
Unit is sealed to protect against splashed liquids, dirt, and dust.
Optical
Light Transmission (per ASTM
90%
D1003)
Visual Resolution
All measurements made using USAF 1951 Resolution Chart,
under 30X magnification, with test unit located approximately
1.5 in (38 mm) from surface of resolution chart.
Clear surface: Excellent, with no noticeable degradation.
Antiglare surface: 6:1 minimum.
Gloss (per ASTM D2457
using a 60-degree gloss meter)
Antiglare surface: Curved: 60 ± 20 gloss units or 75 ± 15 gloss
units.
Environmental
Chemical Resistance
The active area of the touchscreen is resistant to all chemicals
that do not affect glass, such as:
Acetone
Toluene
Methyl ethyl ketone
Isopropyl alcohol
Methyl alcohol
Ethyl acetate
Ammonia-based glass cleaners
Gasoline
Kerosene
Vinegar
Electrostatic Protection (per
EN 61 000-4-2, 1995)
Meets Levels 4 (15kV air/8 kV contact discharge)
C-50 Elo Touchmonitor User Guide
Infrared Touchscreen Specifications
Mechanical
Input Method
Electrical
Input Method Finger or gloved hand activation
Positional Accuracy
Resolution
Typical centroid accuracy: 2 mm with 1 mm STD error
Touchpoint density is based on controller resolution of 4096 x
Touch Activation Force
4096
No minimum touch activation force is required
Controller
Optical
Board: Serial (RS232) or USB 1.1
Light Transmission
Glass overlay: 90% per ASTM D1003-92
Environmental
Chemical Resistance
Glass overlays: The touch active area of the touchscreen is
resistant to chemicals that do not affect glass, such as: acetone,
toluene, methyl ethyl ketone, isopropyl alcohol, methyl alcohol,
ethyl acetate, ammonia-based glass cleaners, gasoline, kerosene,
vinegar. Polycarbonate bezel: around perimeter of display has
some sensitivity to hydrocarbons.
Durability
Surface Durability
Glass filter option: Surface durability is that of glass, Mohs’
hardness rating of 7.
C-51
Acoustic Pulse Recognition Specification
MECHANICAL
Input method
Finger, finger nail, gloved hand, or stylus activation
ELECTRICAL
Position accuracy
1% max. error
Resolution accuracy
Touch activation force
Touchpoint density is based on controller resolution of 4096 x 4096
Typically 2 to 3 ounces (55 to 85 grams)
Controller
OPTICAL
Board: USB 1.1
Light transmission
ENVIRONMENTAL
90%+/-5%
Chemical resistance
The touch activation area of the touchscreen is resistant to chemicals
that do not affect glass such as: acetone, toluene, methyl ethyl ketone,
isopropyl alcohol, methyl alcohol, ethyl acetate, ammonia-based glass
cleaners, gasoline, kerosene, vinegar
DURABILITY
Surface durability
Expected life
Surface durability is that of glass, Mohs’ hardness rating of 7
No known wear-out mechanism, as there are no layers, coatings, or moving
parts. APR technology has been operationally tested to more than 50
million touches in one location without failure, using a stylus similar
finger.
C-52 Elo Touchmonitor User Guide
15” LCD Touchmonitor(ET1529L-XXXA-1-XX-G) Dimensions
15” LCD Touchmonitor(ET1529L-XXXA-1-XX-T-G) Dimensions
C-53
C-54 Elo Touchmonitor User Guide
REGULATORY INFORMATION
I. Electrical Safety Information:
A) Compliance is required with respect to the voltage, frequency, and current requirements indicated on the manufacturer’s label. Connection to a different power source
than those specified herein will likely result in improper operation, damage to the equipment or pose a fire hazard if the limitations are not followed.
B) There are no operator serviceable parts inside this equipment. There are hazardous
voltages generated by this equipment which constitute a safety hazard. Service should
be provided only by a qualified service technician.
C) This equipment is provided with a detachable power cord which has an integral safety
ground wire intended for connection to a grounded safety outlet.
1) Do not substitute the cord with other than the provided approved type. Under
no circumstances use an adapter plug to connect to a 2-wire outlet as this will
defeat the continuity of the grounding wire.
2) The equipment requires the use of the ground wire as a part of the safety
certification, modification or misuse can provide a shock hazard that can result
in serious injury or death.
3) Contact a qualified electrician or the manufacturer if there are questions about
the installation prior to connecting the equipment to mains power.
II. Emissions and Immunity Information
A) Notice to Users in the United States: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules.
These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
B) Notice to Users in Canada: This equipment complies with the Class B limits for radio
noise emissions from digital apparatus as established by the Radio Interference Regulations of Industrie Canada.
C) Notice to Users in the European Union: Use only the provided power cords and
interconnecting cabling provided with the equipment. Substitution of provided cords
and cabling may compromise electrical safety or CE Mark Certification for emissions or
immunity as required by the following standards:
55
This Information Technology Equipment (ITE) is required to have a CE Mark on
the manufacturer’s label which means that the equipment has been tested to the
following Directives and Standards:
This equipment has been tested to the requirements for the CE Mark as required
by EMC Directive 89/336/EEC indicated in European Standard EN 55 022 Class
B and the Low Voltage Directive 73/23/EEC as indicated in European Standard
EN 60 950.
D) General Information to all Users: This equipment generates, uses and can radiate
radio frequency energy. If not installed and used according to this manual the equipment
may cause interference with radio and television communications. There is, however, no
guarantee that interference will not occur in any particular installation due to site-specific factors.
1) In order to meet emission and immunity requirements, the user must observe
the following:
a) Use only the provided I/O cables to connect this digital device with any
computer.
b) To ensure compliance, use only the provided manufacturer’s approved
line cord.
c) The user is cautioned that changes or modifications to the equipment
not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
2) If this equipment appears to cause interference with radio or television reception, or
any other device:
a) Verify as an emission source by turning the equipment off and on.
b) If you determine that this equipment is causing the interference, try to
correct the interference by using one or more of the following measures:
i) Move the digital device away from the affected receiver.
ii) Reposition (turn) the digital device with respect to the affected
receiver.
iii) Reorient the affected receiver’s antenna.
iv) Plug the digital device into a different AC outlet so the digital
device and the receiver are on different branch circuits.
v) Disconnect and remove any I/O cables that the digital device
does not use. (Unterminated I/O cables are a potential source of
high RF emission levels.)
vi) Plug the digital device into only a grounded outlet receptacle.
Do not use AC adapter plugs. (Removing or cutting the line cord
ground may increase RF emission levels and may also present a
lethal shock hazard to the user.)
If you need additional help, consult your dealer, manufacturer, or an experienced radio
or television technician.
56 Elo Touchmonitor User Guide
REP
AR
U B L I CA
G E N TI N A
"The application of this monitor is restricted to special controlled luminous environments.The screen surface trend to
reflect annoying light of lamps and sunlight. To avoid these reflections the monitor should not be positioned in front of a
window or directed to luminaries. The monitor is in compliance with Reflection Class III according to ISO
13406-2"
"Die Anwendung dieses Bildschirms ist auf speziel kontrollierte
Umgebungsbeleuchtungen eingeschränkt. Die Bildschirmoberfläche neigt zu störenden Spielungen von Lampen und
Sonnenlicht. Um diese Refelxionen zu vermeiden sollte der Monitor nicht auf Fenster und Beleuchtungseinrichtungen
ausgerichtet sein. Der Monitor erfüllt nur die Relexionsklasse III nach ISO 13406-2"
This class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) This device must accept any interference reveived, including interference that
may cause undesired operation.
CAUTION:
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by
the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.
VORSICHT:
Explosionsgetahr bei unsachgemäßen Austausch der Batterie. Ersatz nur durch denselben oder einem vom Hersteller
empfohlenem ähnljchen Typ. Entsorgung gebrauchter Batterien nach Angaben des Herstellers.
57
58 Elo Touchmonitor User Guide
WARRANTY
Except as otherwise stated herein or in an order acknowledgment delivered to Buyer,
Seller warrants to Buyer that the Product shall be free of defects in materials and
workmanship. With the exception of the negotiated warranty periods; the warranty for
the touchmonitor and components of the product is 2 years.
Seller makes no warranty regarding the model life of components. Seller’s suppliers
may at any time and from time to time make changes in the components delivered as
Products or components.
Buyer shall notify Seller in writing promptly (and in no case later than thirty
(30) days after discovery) of the failure of any Product to conform to the warranty set
forth above; shall describe in commercially reasonable detail in such notice the symptoms associated with such failure; and shall provide to Seller the opportunity to inspect
such Products as installed, if possible. The notice must be received by Seller during the
Warranty Period for such product, unless otherwise directed in writing by the Seller.
Within thirty (30) days after submitting such notice, Buyer shall package the allegedly
defective Product in its original shipping carton(s) or a functional equivalent and shall
ship to Seller at Buyer’s expense and risk.
Within a reasonable time after receipt of the allegedly defective Product and verification
by Seller that the Product fails to meet the warranty set forth above, Seller shall correct
such failure by, at Seller’s options, either (i) modifying or repairing the Product or (ii)
replacing the Product. Such modification, repair, or replacement and the return shipment of the Product with minimum insurance to Buyer shall be at Seller’s expense.
Buyer shall bear the risk of loss or damage in transit, and may insure the Product. Buyer
shall reimburse Seller for transportation cost incurred for Product returned but not found
by Seller to be defective. Modification or repair, of Products may, at Seller’s option,
take place either at Seller’s facilities or at Buyer’s premises. If Seller is unable to modify,
repair, or replace a Product to conform to the warranty set forth above, then Seller shall,
at Seller’s option, either refund to Buyer or credit to Buyer’s account the purchase price
of the Product less depreciation calculated on a straight-line basis over Seller’s stated
Warranty Period.
59
THESE REMEDIES SHALL BE THE BUYER’S EXCLUSIVE REMEDIES FOR
BREACH OF WARRANTY. EXCEPT FOR THE EXPRESS WARRANTY SET
FORTH ABOVE, SELLER GRANTS NO OTHER WARRANTIES, EXPRESS OR
IMPLIED BY STATUTE OR OTHERWISE, REGARDING THE PRODUCTS, THEIR
FITNESS FOR ANY PURPOSE, THEIR QUALITY, THEIR MERCHANTABILITY,
THEIR NONINFRINGEMENT, OR OTHERWISE. NO EMPLOYEE OF SELLER
OR ANY OTHER PARTY IS AUTHORIZED TO MAKE ANY WARRANTY FOR
THE GOODS OTHER THAN THE WARRANTY SET FORTH HEREIN. SELLER’S
LIABILITY UNDER THE WARRANTY SHALL BE LIMITED TO A REFUND OF
THE PURCHASE PRICE OF THE PRODUCT. IN NO EVENT SHALL SELLER BE
LIABLE FOR THE COST OF PROCUREMENT OR INSTALLATION OF SUBSTITUTE GOODS BY BUYER OR FOR ANY SPECIAL, CONSEQUENTIAL,
INDIRECT, OR INCIDENTAL DAMAGES.
Buyer assumes the risk and agrees to indemnify Seller against and hold Seller harmless
from all liability relating to (i) assessing the suitability for Buyer’s intended use of the
Products and of any system design or drawing and (ii) determining the compliance of
Buyer’s use of the Products with applicable laws, regulations, codes, and standards.
Buyer retains and accepts full responsibility for all warranty and other claims relating to
or arising from Buyer’s products, which include or incorporate Products or components
manufactured or supplied by Seller. Buyer is solely responsible for any and all representations and warranties regarding the Products made or authorized by Buyer. Buyer will
indemnify Seller and hold Seller harmless from any liability, claims, loss, cost, or
expenses (including reasonable attorney’s fees) attributable to Buyer’s products or
representations or warranties concerning same.
60 Elo Touchmonitor User Guide
INDEX
Numerics
F
15.0" LCD Touchmonitor (1529L-XXWA-1-G)
Dimensions, 53
Finger Print Reader, 3
G
A
About Touchmonitor Adjustments, 31
AccuTouch Touchscreen Specifications, 49
Acoustic Pulse Recognition Specification, 52
Auto Adjust, 34
General Power Saving Mode, 35
Gloss, AccuTouch, 49
Gloss, IntelliTouch, 50
Mechanical, AccuTouch, 49
Mechanical, IntelliTouch, 50
B
H
Barcode Scanner, 4,28
Base Bottom View, 9
Brightness, 34
Haze, AccuTouch, 49
I
Infrared Touchscreen Specifications, 51
Input Method, 51
Installation and Setup, 7
Installing the Peripheral Device Drivers, 24
Installing the Touch Driver Software, 30
Installing the USB Touch Driver, 30
Installing the USB Touch Driver for Windows XP,
Windows 2000, Me and 98, 30
IntelliTouch Touchscreen Specifications, 50
C
Care and Handling of Your Touchmonitor, 46
Chemical Resistance, IntelliTouch, 50
Chemical Resistance, IR, 51
Cleaning Your Touchmonitor, 46
Clock, 34,38
Color Temperature, 34,38
Construction, AccuTouch, 49
Contrast, 34,38
Controller, IR, 51
Controls and Adjustment, 33,37
Credit Card Reader, 5
Current Input, 34,38
Customer Display, 4
K
Kensington™ Lock, 10
L
D
Detailed LCD Display Performance Requirements, 2
Display Angle, 35
Display Modes, 47
Durability, IR, 51
E
Electrical Safety Information, 55
Electrical, IR, 51
Electrostatic Protection, IntelliTouch, 50
Emissions and Immunity Information, 55
Environmental, 50
Environmental, IR, 51
Expected Life Performance, AccuTouch, 49
Expected Life Performance, IntelliTouch, 50
External 12 VDC Power Supply, 6
Language, 35
Light Transmission, AccuTouch, 49
Light Transmission, IntelliTouch, 50
Light Transmission, IR, 51
M
Magnetic Stripe Reader, 25
Main Unit, 8
Mechanical, 43
I N D E X - 61
N
T
Native Resolution, 47
Technical Specifications, 51
Testing Applications/Readme, 32
Testing the USB MSR Keyboard Emulation, 25
Testing the USB-HID Class MSR, 25
Theory of Operation, 4
Touch Activation Force, AccuTouch, 53
Touch Activation Force, IntelliTouch, 54
Touch not working, 45
Touchmonitor Safety, 49
Touchmonitor Specifications, 52
Touchpoint Density, AccuTouch, 53
Touchpoint Density, IntelliTouch, 54
Troubleshooting, 45
O
Omni-directional scanner, 4
Optical, AccuTouch, 53
Optical, IntelliTouch, 54
Optical, IR, 55
Optimizing the LCD Display, 24
OSD Control Options, 38,42
OSD Left/Right, 38,42
OSD Lock/Unlock, 37,41
OSD Menu Functions, 37,41
OSD Position, 38,42
OSD Timeout, 39,43
OSD Up/Down, 38,42
P
Phase, 38,42
Positional Accuracy, AccuTouch, 53
Positional Accuracy, IntelliTouch, 54
Positional Accuracy, IR, 55
Power LED Display & Power Saving, 39
Power Lock/Unlock, 37,41
Power-Save (No Input), 39
Product Description, 1
Product Overview, 8
U
Unpacking Your Touchmonitor, 7
USB Customer Display, 32
USB Interface Connection, 11
V
VGA, 41
Visual Resolution, AccuTouch, 53
Visual Resolution, IntelliTouch, 54
Volume, 43
W
Warranty, 63
R
Rear Facing Customer Display, 32
Rear View, 8
Recall Defaults, 39
Regulatory Information, 59
Remove the Back Cover, 11,17
Replace the Back Cover, 16,23
Resolution, IR, 55
X
XGA, 47
S
Saturation, Hue, Flesh Tones, 38,42
Sealing, IntelliTouch, 54
Sensor Specifications, 5
Side View, 9
Single scanner, 5
Six Port USB Hub, 6
Solutions to Common Problems, 45
Surface Durability, AccuTouch, 53
Surface Durability, IntelliTouch, 54
Surface Durability, IR, 55
SVGA, 47
I N D E X - 62
Check out Elo’s Web site!
www.elotouch.com
Get the latest...
• Product information
• Specifications
• News on upcoming events
• Press release
• Software drivers
• Touchmonitor Newsletter
Getting in Touch with Elo
To find out more about Elo’s extensive range of touch solutions, visit our Web site at www.elotouch.com or simply call the office
nearest you:
North America
Germany
Belgium
Asian-Pacific
Elo TouchSystems
Tyco Electronics Raychem GmbH
Tyco Electronics Raychem GmbH
Sun Homada Bldg. 2F
301 Constitution Drive,
Menlo Park, CA 94025
(Elo TouchSystems Division)
Finsinger Feld 1
(Elo TouchSystems Division)
Diestsesteenweg 692
1-19-20 Shin-Yokohama
Kanagawa 222-0033
USA
D-85521 Ottobrunn
Germany
B-3010 Kessel-Lo
Belgium
Japan
(800) ELO-TOUCH
(800-356-8682)
Tel +49(0)(89)60822-0
Tel +32(0)(16)35-2100
Tel +81(45)478-2161
Tel 650-361-4800
Fax 650-361-4722
Fax +49(0)(89)60822-180
elosales@elotouch.com
Fax +32(o)(16)35-2101
elosales@elotouch.com
Fax +81(45)478-2180
www.tps.co.jp
© 2008 Elo TouchSystems Inc. Printed
in USA
eloinfo@elotouch.com
Download PDF