Dell | Inspiron 15R SE 7520 | Owner`s manual | Dell Inspiron 15R SE 7520 Owner`s manual

Инструкция для
Dell Inspiron 7520
Перейти в карточку товара
8 800 775 98 98
л чит т нич
ю н льт цию.
гл т чн . Б з вы дны
www.sotmarket.ru
д бн я инф м ция
тзывы, бз ы и
т в
ы
,
Dell Inspiron 15R
Owner’s Manual
Computer model: Inspiron 5520/7520
Regulatory model: P25F
Regulatory type: P25F001
Notes, Cautions, and Warnings
NOTE: A NOTE indicates important information that helps you make
better use of your computer.
CAUTION: A CAUTION indicates potential damage to hardware or loss
of data if instructions are not followed.
WARNING: A WARNING indicates a potential for property damage,
personal injury, or death.
____________________
Information in this document is subject to change without notice.
© 2012 Dell Inc. All rights reserved.
Reproduction of these materials in any manner whatsoever without the written permission
of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell™, the DELL logo, and Inspiron™ are trademarks of Dell
are either trademarks
Inc.; Microsoft®, Windows®, and the Windows start button logo
or registered trademarks of Microsoft corporation in the United States and/or other
countries; Bluetooth® is a registered trademark owned by Bluetooth SIG, Inc. and is used
by Dell under license.
Other trademarks and trade names may be used in this document to refer to either the
entities claiming the marks and names or their products. Dell Inc. disclaims any proprietary
interest in trademarks and trade names other than its own.
2012 - 04
Rev. A00
Contents
1
Before You Begin
. . . . . . . . . . . . . . . . . . . . . . . .
Turn Off Your Computer and Connected Devices
Safety Instructions . . . . . . . . . . . . . . . . . . . . .
Recommended Tools . . . . . . . . . . . . . . . . . . .
2
After Working Inside Your Computer .
3
Switch .
4
Battery .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
Keyboard .
. . . . . . . . . . . . . . . . . . . .
13
13
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
. . . . . . . . . . . . . . . . . . . .
Base Cover
. . . . . . . . . . . . . . . . . . .
15
16
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
17
. . . . . . . . . . . . . . . . . . .
Memory Module(s) .
. . . . . . . . . . . . . . . . .
17
18
. . . . . . . . . . . . . . . . . . . . .
19
. . . . . . . . . . . . . . . . .
Removing the Memory Module(s) .
Replacing the Memory Module(s) .
8
Hard Drive .
. . . . . . . . . . . .
19
20
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
21
Removing the Hard Drive
Replacing the Hard Drive
9
11
11
12
Removing the Base Cover .
Replacing the Base Cover .
7
9
. . . . . . . . . . . . . . . . . . . . .
Removing the Keyboard
Replacing the Keyboard
6
. . . . . . .
. . .
. . . . . . . . . . . . . . . . . . . . .
Removing the Battery .
Replacing the Battery .
5
. . .
7
7
8
. . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removing the Switch
Replacing the Switch
7
Optical Drive .
. . . . . . . . . . . .
. . . . . . . . . . . . . . . . . .
21
23
. . . . . . . . . . . . . . . . . . . . . . . . . .
25
. . . . . . . . . . . . . . . . . .
Removing the Optical Drive .
Replacing the Optical Drive .
. . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . .
25
26
Contents
|
3
10 Palm Rest
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removing the Palm Rest .
Replacing the Palm Rest .
11 Power-Adapter Port .
. . . . . . . . . . . . . . . . . .
27
31
. . . . . . . . . . . . . . . . . . . .
33
. . . . . . . . . . . . . . . . . .
Removing the Power-Adapter Port .
Replacing the Power-Adapter Port .
12 Display Assembly
. . . . . . . . . . .
33
34
. . . . . . . . . . . . . . . . . . . . . . .
35
Removing the Display Assembly .
Replacing the Display Assembly .
Removing the Display Bezel . . .
Replacing the Display Bezel . . . .
Removing the Hinge Caps . . . . .
Replacing the Hinge Caps . . . . .
Removing the Display Panel . . .
Replacing the Display Panel . . . .
13 Camera Module
. . . . . . . . . . .
. . . . . . . . . . . . .
35
37
37
38
39
40
40
43
. . . . . . . . . . . . . . . . . . . . . . . .
45
Removing the Camera Module.
Replacing the Camera Module .
14 System Board
. . . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . . .
45
48
. . . . . . . . . . . . . . . . . . . . . . . . . .
49
. . . . . . . . . . . . . .
Removing the System Board . . . . . .
Replacing the System Board . . . . . .
Entering the Service Tag in the BIOS .
15 Thermal-Cooling Assembly .
. . . . . . . . . .
49
52
53
. . . . . . . . . . . . . .
55
. . . . . . . . . .
. . . . . . . . . .
Removing the Thermal-Cooling Assembly .
Replacing the Thermal-Cooling Assembly .
16 Processor
. . . . . .
55
57
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
59
Removing the Processor .
Replacing the Processor .
17 Coin-Cell Battery .
|
Contents
. . . . . .
. . . . . . . . . . . . . . . . . .
59
61
. . . . . . . . . . . . . . . . . . . . . .
63
. . . . . . . . . . . . . . . . . .
Removing the Coin-Cell Battery .
Replacing the Coin-Cell Battery .
4
27
. . . . . . . . . . . . .
. . . . . . . . . . . . .
63
65
18 Speakers
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removing the Speakers
Replacing the Speakers .
19 Media Card Reader .
. . . . . . . . . . . . . . . . . . .
67
69
. . . . . . . . . . . . . . . . . . . . .
71
. . . . . . . . . . . . . . . . . . .
Removing the Media Card Reader
Replacing the Media Card Reader .
20 Daughter Board
. . . . . . . . . . . .
71
73
. . . . . . . . . . . . . . . . . . . . . . . .
75
Removing the Daughter Board .
Replacing the Daughter Board .
21 Mini-Card
67
. . . . . . . . . . . .
. . . . . . . . . . . . . .
75
77
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
79
Removing the Mini-Card .
Replacing the Mini-Card .
22 Flashing the BIOS .
. . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . .
79
80
. . . . . . . . . . . . . . . . . . . . . .
83
. . . . . . . . . . . . . . . . . .
Contents
|
5
6
|
Contents
1
Before You Begin
Turn Off Your Computer and Connected Devices
CAUTION: To avoid losing data, save and close all open files and exit all open
programs before you turn off your computer.
1
Save and close all open files and exit all open programs.
2
Click Start
and click Shut down.
Microsoft Windows shuts down and then the computer turns off.
NOTE: If you are using a different operating system, see the documentation of
your operating system for shut-down instructions.
3
Disconnect your computer and all attached devices from their electrical outlets.
4
Disconnect all telephone cables, network cables, and attached devices from your
computer.
5
Press and hold the power button for about 5 seconds, after the computer is
unplugged, to ground the system board.
Safety Instructions
Use the following safety guidelines to protect your computer from potential damage and
ensure your personal safety.
WARNING: Before working inside your computer, read the safety information
that shipped with your computer. For additional safety best practices
information, see the Regulatory Compliance Homepage at dell.com/
regulatory_compliance.
WARNING: Disconnect all power sources before opening the computer cover or
panels. After you finish working inside the computer, replace all covers, panels,
and screws before connecting to the power source.
CAUTION: To avoid damaging the computer, ensure that the work surface is flat
and clean.
CAUTION: To avoid damaging the components and cards, handle them by their
edges and avoid touching pins and contacts.
CAUTION: Only a certified service technician is authorized to remove the
computer cover and access any of the components inside the computer. See the
safety instructions for complete information about safety precautions, working
inside your computer, and protecting against electrostatic discharge.
CAUTION: Before touching anything inside your computer, ground yourself by
touching an unpainted metal surface, such as the metal at the back of the
computer. While you work, periodically touch an unpainted metal surface to
dissipate static electricity, which could harm internal components.
Before You Begin
|
7
CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab,
not on the cable itself. Some cables have connectors with locking tabs or
thumb-screws that you must disengage before disconnecting the cable. When
disconnecting cables, keep them evenly aligned to avoid bending any connector
pins. When connecting cables, ensure that the connectors and ports are correctly
oriented and aligned.
CAUTION: To disconnect a network cable, first unplug the cable from your
computer and then unplug the cable from the network device.
Recommended Tools
The procedures in this document may require the following tools:
8
•
Phillips screwdriver
•
Plastic scribe
•
Small flat-blade screwdriver
|
Before You Begin
2
After Working Inside Your Computer
After you complete replacement procedures, ensure the following:
•
Replace all screws and ensure that no stray screws remain inside your computer
•
Connect any external devices, cables, cards, and any other part(s) you removed
before working on your computer
•
Connect your computer and all attached devices to their electrical outlets
CAUTION: Before turning on your computer, replace all screws and ensure that
no stray screws remain inside the computer. Failure to do so may damage your
computer.
After Working Inside Your Computer
|
9
10
|
After Working Inside Your Computer
3
Switch
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 7. For additional safety best practices information, see the Regulatory
Compliance Homepage at dell.com/regulatory_compliance.
Removing the Switch
1
Slide the switch release latch to the side.
The switch pops up.
2
Lift the switch off the computer.
3
2
1
1
display cover
3
switch
2
switch release latch
Switch
|
11
Replacing the Switch
Procedure
Align the tabs at the bottom of the switch with the slots on the display cover and
snap the switch into place.
1
4
3
2
1
1
display cover
2
slots
3
tabs
4
switch
2
Follow the instructions in "After Working Inside Your Computer" on page 9.
12
|
Switch
4
Battery
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 7. For additional safety best practices information, see the Regulatory
Compliance Homepage at dell.com/regulatory_compliance.
Removing the Battery
1
Close the display and turn the computer over.
2
Slide the battery release latches to the unlock position.
3
Lift the battery out of the battery bay.
2
1
1 battery release latches (2)
2 battery
Replacing the Battery
1
Align the tabs on the battery with the slots on the battery bay and snap the battery
until it clicks into place.
2
Follow the instructions in "After Working Inside Your Computer" on page 9.
Battery
|
13
14
|
Battery
5
Keyboard
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 7. For additional safety best practices information, see the Regulatory
Compliance Homepage at dell.com/regulatory_compliance.
Removing the Keyboard
Prerequisites
1
Remove the battery. See "Removing the Battery" on page 13.
Procedure
CAUTION: The keycaps on the keyboard are fragile, easily dislodged, and
time-consuming to replace. Be careful when removing and handling the keyboard.
1
Turn the computer over and open the display as far as possible.
2
Using a plastic scribe, release the keyboard from the tabs on the palm rest and ease
the keyboard up until it clears off the palm rest.
CAUTION: Be extremely careful when removing and handling the keyboard.
Failure to do so could result in scratching the display panel.
1
2
3
4
1 tabs (4)
2 plastic scribe
3 keyboard
4 palm rest
Keyboard
|
15
3
Carefully turn the keyboard over and place it on the palm rest.
4
Lift the connector latch and pull the pull-tab to disconnect the keyboard cable
from the connector on the system board.
5
Lift the keyboard away from the computer.
1
2
3
1 keyboard cable
2 connector latch
3 tabs (5)
Replacing the Keyboard
Procedure
1
Slide the keyboard cable into the connector on the system board and press down
on the connector latch to secure the cable.
2
Slide the tabs at the bottom of the keyboard into the slots on the palm rest and
place the keyboard on the palm rest.
3
Gently press around the edges of the keyboard to secure the keyboard under the
tabs on the palm rest.
4
Close the display and turn the computer over.
Postrequisites
1
Replace the battery. See "Replacing the Battery" on page 13.
2
Follow the instructions in "After Working Inside Your Computer" on page 9.
16
|
Keyboard
6
Base Cover
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 7. For additional safety best practices information, see the Regulatory
Compliance Homepage at dell.com/regulatory_compliance.
Removing the Base Cover
Prerequisites
1
Remove the battery. See "Removing the Battery" on page 13.
Procedure
1
Loosen the captive screws that secure the base cover to the computer base.
2
Using your fingertips, pry the base cover from the computer base.
3
Lift the base cover off the computer base.
2
1
1
base cover
2
captive screws (3)
Base Cover
|
17
Replacing the Base Cover
Procedure
1
Slide the tabs on the base cover into the slots on the computer base and snap the
base cover into place.
2
Tighten the captive screws that secure the base cover to the computer base.
Postrequisites
1
Replace the battery. See "Replacing the Battery" on page 13.
2
Follow the instructions in "After Working Inside Your Computer" on page 9.
18
|
Base Cover
7
Memory Module(s)
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 7. For additional safety best practices information, see the Regulatory
Compliance Homepage at dell.com/regulatory_compliance.
Removing the Memory Module(s)
Prerequisites
1
Remove the battery. See "Removing the Battery" on page 13.
2
Remove the base cover. See "Removing the Base Cover" on page 17.
Procedure
CAUTION: To prevent damage to the memory-module connector, do not use
tools to spread the memory-module securing clips.
1
Use your fingertips to carefully spread apart the securing clips on each end of the
memory-module connector until the memory module pops up.
2
Remove the memory module from the memory-module connector.
1
3
2
1
memory-module connector
3
memory module
2
securing clips (2)
Memory Module(s)
|
19
Replacing the Memory Module(s)
Procedure
1
Align the notch on the memory module with the tab on the memory-module
connector.
2
Slide the memory module firmly into the slot at a 45-degree angle, and press the
memory module down until it clicks into place. If you do not hear the click, remove
the memory module and reinstall it.
NOTE: If the memory module is not installed properly, the computer may not
boot.
2
1
1
tab
2
notch
Postrequisites
1
Replace the base cover. See "Replacing the Base Cover" on page 18.
2
Replace the battery. See "Replacing the Battery" on page 13.
3
Follow the instructions in "After Working Inside Your Computer" on page 9.
4
Turn on the computer.
As the computer boots, it detects the memory module(s) and automatically updates the
system configuration information.
To confirm the amount of memory installed in the computer:
Click Start
20
|
→ Control Panel→ System and Security→ System.
Memory Module(s)
8
Hard Drive
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 7. For additional safety best practices information, see the Regulatory
Compliance Homepage at dell.com/regulatory_compliance.
CAUTION: To avoid data loss, do not remove the hard drive while the computer is
On or in Sleep state.
CAUTION: Hard drives are extremely fragile. Exercise care when handling the
hard drive.
Removing the Hard Drive
Prerequisites
1
Remove the battery. See "Removing the Battery" on page 13.
2
Remove the base cover. See "Removing the Base Cover" on page 17.
Hard Drive
|
21
Procedure
1
Remove the screws that secure the hard-drive assembly to the computer base.
2
Using the pull-tab, slide the hard-drive assembly toward the back of the computer
to disconnect the hard-drive assembly from the connector on the system board.
3
Lift the hard-drive assembly out of the computer base.
1
2
3
1
pull-tab
3
hard-drive assembly
22
|
Hard Drive
2
screws (4)
4
Remove the screws that secure the hard-drive bracket to the hard drive.
5
Lift the hard drive off the hard-drive bracket.
3
2
1
1
screws (4)
3
hard-drive bracket
2
hard drive
Replacing the Hard Drive
Procedure
1
Remove the new hard drive from its packaging.
Save the original packaging for storing or shipping the hard drive.
2
Align the screw holes on the hard drive-bracket with the screw holes on the hard
drive.
3
Replace the screws that secure the hard-drive bracket to the
hard drive.
4
Place the hard-drive assembly on the computer base.
5
Using the pull-tab, slide the hard-drive assembly toward the front of the computer,
to connect the hard-drive assembly to the connector on the system board.
6
Replace the screws that secure the hard-drive assembly to the computer base.
Hard Drive
|
23
Postrequisites
1
Replace the base cover. See "Replacing the Base Cover" on page 18.
2
Replace the battery. See "Replacing the Battery" on page 13.
3
Follow the instructions in "After Working Inside Your Computer" on page 9.
24
|
Hard Drive
9
Optical Drive
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 7. For additional safety best practices information, see the Regulatory
Compliance Homepage at dell.com/regulatory_compliance.
Removing the Optical Drive
Prerequisites
1
Remove the battery. See "Removing the Battery" on page 13.
2
Remove the base cover. See "Removing the Base Cover" on page 17.
Procedure
1
Remove the screw that secures the optical-drive assembly to the computer base.
2
Using your fingertips, slide the optical-drive assembly out of the optical-drive bay.
2
1
1
optical-drive assembly
2
screw
Optical Drive
|
25
3
Carefully pry the optical-drive bezel and remove it from the optical-drive assembly.
4
Remove the screws that secure the optical-drive bracket to the optical drive.
5
Remove the optical-drive bracket.
3
4
2
1
1
optical-drive bezel
2
optical drive
3
optical-drive bracket
4
screws (2)
Replacing the Optical Drive
Procedure
1
Align the screw holes on the optical-drive bracket with the screw holes on the
optical drive.
2
Replace the screws that secure the optical-drive bracket to the optical drive.
3
Align the tabs on the optical-drive bezel with the slots on the optical-drive
assembly and snap the optical-drive bezel into place.
4
Slide the optical-drive assembly into the optical-drive bay until it is fully seated.
5
Replace the screw that secures the optical-drive assembly to the computer base.
Postrequisites
1
Replace the base cover. See "Replacing the Base Cover" on page 18.
2
Replace the battery. See "Replacing the Battery" on page 13.
3
Follow the instructions in "After Working Inside Your Computer" on page 9.
26
|
Optical Drive
10
Palm Rest
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 7. For additional safety best practices information, see the Regulatory
Compliance Homepage at dell.com/regulatory_compliance.
Removing the Palm Rest
Prerequisites
1
Remove the battery. See "Removing the Battery" on page 13.
2
Remove the keyboard. See "Removing the Keyboard" on page 15.
3
Remove the base cover. See "Removing the Base Cover" on page 17.
Procedure
1
Remove the screws that secure the palm rest to the computer base.
Palm Rest
|
27
2
Turn the computer over.
3
Lift the connector latches and pull the pull-tabs to disconnect the power-button
board cable, touchpad cable, and hot-key board cable from the connectors on the
system board.
1 2
3
4
1 power-button board cable
2 pull-tab
3 connector latch
4 touchpad cable
5 hot-key board cable
28
|
Palm Rest
5
4
Remove the screws that secure the palm rest to the computer base.
5
Using your fingertips, pry out the palm rest from the computer base.
CAUTION: Carefully separate the palm rest from the display assembly to avoid
damage to the display assembly.
1
2
1
screws (6)
2
palm rest
Palm Rest
|
29
6
Without pulling hard on the palm-rest assembly, place it away from the display as
shown in the illustration below.
7
Lift the connector latch and pull the pull-tab to disconnect the status-lights cable
from the connector on the system board.
8
Lift the palm-rest assembly off the computer base.
1 2
3
1 connector latch
3 status-lights cable
30
|
Palm Rest
2 pull-tab
Replacing the Palm Rest
Procedure
1
Slide the status-lights cable into the connector on the system board and press
down on the connector latch to secure the cable.
2
Align the palm rest with the computer base and gently snap the palm rest into
place.
3
Slide the hot-key board cable, power-button board cable, and touchpad cable into
the connectors on the system board and press down on the connector latches to
secure the cables.
4
Replace the screws that secure the palm rest to the computer base.
5
Turn the computer over and replace the screws that secure the palm rest to the
computer base.
Postrequisites
1
Replace the base cover. See "Replacing the Base Cover" on page 18.
2
Replace the keyboard. See "Replacing the Keyboard" on page 16.
3
Replace the battery. See "Replacing the Battery" on page 13.
4
Follow the instructions in "After Working Inside Your Computer" on page 9.
Palm Rest
|
31
32
|
Palm Rest
11
Power-Adapter Port
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 7. For additional safety best practices information, see the Regulatory
Compliance Homepage at dell.com/regulatory_compliance.
Removing the Power-Adapter Port
Prerequisites
1
Remove the battery. See "Removing the Battery" on page 13.
2
Remove the keyboard. See "Removing the Keyboard" on page 15.
3
Remove the base cover. See "Removing the Base Cover" on page 17.
4
Remove the palm rest. See "Removing the Palm Rest" on page 27.
Procedure
1
Remove the screws that secure the power-adapter port bracket to the computer
base.
2
Lift the power-adapter port bracket off the computer base.
1
2
1 screws (2)
2 power-adapter port bracket
Power-Adapter Port
|
33
3
Disconnect the power-adapter port cable from the connector on the system board.
4
Lift the power-adapter port off the computer base.
1
2
3
1 power-adapter port cable
2 system-board connector
3 power-adapter port
Replacing the Power-Adapter Port
Procedure
1
Place the power-adapter port in the slot on the computer base.
2
Connect the power-adapter port cable to the connector on the system board.
3
Align the screw holes on the power-adapter port bracket with the screw holes on
the computer base.
4
Replace the screws that secure the power-adapter port bracket to the computer
base.
Postrequisites
1
Replace the palm rest. See "Replacing the Palm Rest" on page 31.
2
Replace the base cover. See "Replacing the Base Cover" on page 18.
3
Replace the keyboard. See "Replacing the Keyboard" on page 16.
4
Replace the battery. See "Replacing the Battery" on page 13.
5
Follow the instructions in "After Working Inside Your Computer" on page 9.
34
|
Power-Adapter Port
12
Display Assembly
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 7. For additional safety best practices information, see the Regulatory
Compliance Homepage at dell.com/regulatory_compliance.
Removing the Display Assembly
Prerequisites
1
Remove the battery. See "Removing the Battery" on page 13.
2
Remove the keyboard. See "Removing the Keyboard" on page 15.
3
Remove the base cover. See "Removing the Base Cover" on page 17.
4
Remove the palm rest. See "Removing the Palm Rest" on page 27.
Display Assembly
|
35
Procedure
1
Disconnect the antenna cables from the connectors on the Mini-Card.
2
Peel the tape that secures the display cable to the system board and then
disconnect the display cable from the connector on the system board.
3
Make a note of the display cable routing and remove the cable from the routing
guides.
4
Remove the screws that secure the display assembly to the computer base.
5
Lift the display assembly off the computer base.
5
1
2
4
3
1 display assembly
2 screws (6)
3 tape
4 display cable
5 antenna cables (2)
36
|
Display Assembly
Replacing the Display Assembly
Procedure
1
Place the display assembly in position and replace the screws that secure the
display assembly to the computer base.
2
Route the display cable through the routing guides and connect the display cable
to the connector on the system board.
3
Adhere the tape that secures the display cable to the system board.
4
Connect the antenna cables to the connectors on the Mini-Card.
Postrequisites
1
Replace the palm rest. See "Replacing the Palm Rest" on page 31.
2
Replace the base cover. See "Replacing the Base Cover" on page 18.
3
Replace the keyboard. See "Replacing the Keyboard" on page 16.
4
Replace the battery. See "Replacing the Battery" on page 13.
5
Follow the instructions in "After Working Inside Your Computer" on page 9.
Removing the Display Bezel
Prerequisites
1
Remove the battery. See "Removing the Battery" on page 13.
2
Remove the keyboard. See "Removing the Keyboard" on page 15.
3
Remove the base cover. See "Removing the Base Cover" on page 17.
4
Remove the palm rest. See "Removing the Palm Rest" on page 27.
5
Remove the display assembly. See "Removing the Display Assembly" on page 35.
Display Assembly
|
37
Procedure
CAUTION: The display bezel is extremely fragile. Be careful when removing it to
prevent damaging the display bezel.
1
Using your fingertips, carefully pry up the inside edge of the display bezel.
2
Remove the display bezel.
1
1 display bezel
Replacing the Display Bezel
Procedure
Align the display bezel with the display cover and gently snap the display bezel into place.
Postrequisites
1
Replace the display assembly. See "Replacing the Display Assembly" on page 37.
2
Replace the palm rest. See "Replacing the Palm Rest" on page 31.
3
Replace the base cover. See "Replacing the Base Cover" on page 18.
4
Replace the keyboard. See "Replacing the Keyboard" on page 16.
5
Replace the battery. See "Replacing the Battery" on page 13.
6
Follow the instructions in "After Working Inside Your Computer" on page 9.
38
|
Display Assembly
Removing the Hinge Caps
Prerequisites
1
Remove the battery. See "Removing the Battery" on page 13.
2
Remove the keyboard. See "Removing the Keyboard" on page 15.
3
Remove the base cover. See "Removing the Base Cover" on page 17.
4
Remove the palm rest. See "Removing the Palm Rest" on page 27.
5
Remove the display assembly. See "Removing the Display Assembly" on page 35.
6
Remove the display bezel. See "Removing the Display Bezel" on page 37.
Procedure
1
Remove the screws that secure the hinge caps to the display cover.
2
Lift the hinge cap, and slide the antenna cables through the slot on the hinge cap.
3
2
1
1 hinge caps (2)
2 screws (4)
3 display cover
Display Assembly
|
39
Replacing the Hinge Caps
Procedure
1
Slide the antenna cables through the slot on the hinge cover
2
Align the screw holes on the hinge caps with the screw holes on the display cover.
3
Replace the screws that secure the hinge caps to the display cover.
Postrequisites
1
Replace the display bezel. See "Replacing the Display Bezel" on page 38.
2
Replace the display assembly. See "Replacing the Display Assembly" on page 37.
3
Replace the palm rest. See "Replacing the Palm Rest" on page 31.
4
Replace the base cover. See "Replacing the Base Cover" on page 18.
5
Replace the keyboard. See "Replacing the Keyboard" on page 16.
6
Replace the battery. See "Replacing the Battery" on page 13.
Removing the Display Panel
Prerequisites
1
Remove the battery. See "Removing the Battery" on page 13.
2
Remove the keyboard. See "Removing the Keyboard" on page 15.
3
Remove the base cover. See "Removing the Base Cover" on page 17.
4
Remove the palm rest. See "Removing the Palm Rest" on page 27.
5
Remove the display assembly. See "Removing the Display Assembly" on page 35.
6
Remove the display bezel. See "Removing the Display Bezel" on page 37.
7
Remove the hinge caps. See "Removing the Hinge Caps" on page 39.
40
|
Display Assembly
Procedure
1
Remove the screws that secure the display panel to the display cover.
2
Carefully lift the display panel and turn it over.
1
2
3
1 display cover
2 display panel
3 screws (8)
Display Assembly
|
41
3
Peel and lift the tape that secures the display cable to the display-board connector
and disconnect the display cable.
4
Peel the display cable from the back of the display panel.
1
2
1 display cable
2 display-board connector
3 tape
42
|
Display Assembly
3
5
Turn the display panel over and place it on a clean surface.
6
Remove the screws that secure the display-panel brackets to the display panel.
7
Remove the display-panel brackets off the display panel.
3
2
1
1 screws (8)
2 display-panel brackets (2)
3 display panel
Replacing the Display Panel
Procedure
1
Align the screw holes on the display-panel bracket with the screw holes on the
display panel and replace the screws that secure the display-panel bracket to the
display panel.
2
Turn the display panel over.
3
Adhere the display cable to the back of the display panel.
4
Connect the display cable to the display-board connector and secure it with the
tape.
5
Align the screw holes on the display panel with the screw holes on the display cover
and replace the screws that secure the display panel to the display cover.
Display Assembly
|
43
Postrequisites
1
Replace the hinge caps. See "Replacing the Hinge Caps" on page 40.
2
Replace the display bezel. See "Replacing the Display Bezel" on page 38.
3
Replace the display assembly. See "Replacing the Display Assembly" on page 37.
4
Replace the palm rest. See "Replacing the Palm Rest" on page 31.
5
Replace the base cover. See "Replacing the Base Cover" on page 18.
6
Replace the keyboard. See "Replacing the Keyboard" on page 16.
7
Replace the battery. See "Replacing the Battery" on page 13.
8
Follow the instructions in "After Working Inside Your Computer" on page 9.
44
|
Display Assembly
13
Camera Module
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 7. For additional safety best practices information, see the Regulatory
Compliance Homepage at dell.com/regulatory_compliance.
Removing the Camera Module
Prerequisites
1
Remove the battery. See "Removing the Battery" on page 13.
2
Remove the keyboard. See "Removing the Keyboard" on page 15.
3
Remove the base cover. See "Removing the Base Cover" on page 17.
4
Remove the palm rest. See "Removing the Palm Rest" on page 27.
5
Remove the display assembly. See "Removing the Display Assembly" on page 35.
6
Remove the display bezel. See "Removing the Display Bezel" on page 37.
Camera Module
|
45
Procedure
1
Remove the screws that secure the display panel to the display cover.
2
Carefully lift the display panel and turn it over.
1
2
3
1 display cover
2 display panel
3 screws (8)
46
|
Camera Module
3
Disconnect the camera cable from the connector on the camera module.
.
1
2
1 camera module
2 camera cable
4
Remove the screw that secures the camera module to the display cover.
5
Lift the camera module off the display cover.
4
3
2
1
1 tab
2 display cover
3 camera module
4 screw
Camera Module
|
47
Replacing the Camera Module
Procedure
1
Use the alignment posts on the display cover to place the camera module
in position.
Ensure that the camera module is secured under the tab on the display cover.
2
Connect the camera cable to the connector on the camera module.
3
Replace the screw that secures the camera module to the display cover.
4
Turn the display panel over and place it on the display cover.
5
Align the screw holes on the display panel with the screw holes on the
display cover.
6
Replace the screws that secure the display panel to the display cover.
Postrequisites
1
Replace the display bezel. See "Replacing the Display Bezel" on page 38.
2
Replace the display assembly. See "Replacing the Display Assembly" on page 37.
3
Replace the palm rest. See "Replacing the Palm Rest" on page 31.
4
Replace the base cover. See "Replacing the Base Cover" on page 18.
5
Replace the keyboard. See "Replacing the Keyboard" on page 16.
6
Replace the battery. See "Replacing the Battery" on page 13.
7
Follow the instructions in "After Working Inside Your Computer" on page 9.
48
|
Camera Module
14
System Board
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 7. For additional safety best practices information, see the Regulatory
Compliance Homepage at dell.com/regulatory_compliance.
Removing the System Board
Prerequisites
1
Remove the battery. See "Removing the Battery" on page 13.
2
Remove the base cover. See "Removing the Base Cover" on page 17.
3
Remove the memory module(s). See "Removing the Memory Module(s)" on
page 19.
4
Follow the instructions from step 1 to step 3 in "Removing the Hard Drive" on
page 21.
5
Follow the instructions from step 1 to step 2 in "Removing the Optical Drive" on
page 25.
6
Remove the keyboard. See "Removing the Keyboard" on page 15.
7
Remove the palm rest. See "Removing the Palm Rest" on page 27.
System Board
|
49
Procedure
NOTE: Your computer’s Service Tag is stored in the system board. You must enter
the Service Tag in the BIOS after you replace the system-board assembly.
NOTE: Before disconnecting the cables from the system board, note the location
of the connectors so that you can reconnect them correctly after you replace the
system-board assembly.
1
Remove the screws that secure the power-adapter port bracket to the computer
base.
2
Lift the power-adapter port bracket off the computer base.
1
2
1 screws (2)
50
|
System Board
2 power-adapter port bracket
3
Disconnect the power-adapter port cable, fan cable, and speakers cable from the
connectors on the system board.
4
Peel the tape that secures the display cable to the system board and then
disconnect the display cable from the connector on the system board.
5
Lift the connector latch and pull the pull-tab to disconnect the Media Card Reader
cable from the connector on the system board.
.
8
9
7
6
5
1
2
3
4
1 power-adapter port cable
2 fan cable
3 system-board assembly
4 speakers cable
5 connector latch
6 pull-tab
7 Media Card Reader cable
8 display cable
9 tape
System Board
|
51
6
Remove the screws that secure the system board to the computer base.
7
Lift the system board to disconnect the connector on the system board from the
connector on the daughter board.
8
Lift the system board at an angle and release the connectors on the system board
from the slots on the computer base.
2
1
1 system-board assembly
9
10
2 screws (6)
Remove the thermal-cooling assembly. See "Removing the Thermal-Cooling
Assembly" on page 55.
Remove the processor. See "Removing the Processor" on page 59.
Replacing the System Board
Procedure
1
Replace the processor. See "Replacing the Processor" on page 61.
2
Replace the thermal-cooling assembly. See "Replacing the Thermal-Cooling
Assembly" on page 57.
3
Slide the connectors on the system board into the slots on the computer base.
4
Gently press the system board to connect the connector on the system board to
the connector on the daughter board.
5
Replace the screws that secure the system board to the computer base.
52
|
System Board
6
Slide the Media Card Reader cable into the connector on the system board and
press down on the connector latch to secure the cable.
7
Connect the display cable to the connector on the system board and adhere the
tape that secures the cable to the system board.
8
Connect the power-adapter port cable, fan cable, and speakers cable to the
connectors on the system board.
9
Align the screw holes on the power-adapter port bracket with the screw holes on
the computer base.
10
Replace the screws that secure the power-adapter port bracket to the computer
base.
Postrequisites
1
Replace the palm rest. See "Replacing the Palm Rest" on page 31.
2
Replace the keyboard. See "Replacing the Keyboard" on page 16.
3
Follow the instructions from step 4 to step 5 in "Replacing the Optical Drive" on
page 26.
4
Follow the instructions from step 4 to step 6 in "Replacing the Hard Drive" on
page 23.
5
Replace the memory module(s). See "Replacing the Memory Module(s)" on
page 20.
6
Replace the base cover. See "Replacing the Base Cover" on page 18.
7
Replace the battery. See "Replacing the Battery" on page 13.
8
Follow the instructions in "After Working Inside Your Computer" on page 9.
Entering the Service Tag in the BIOS
1
Turn on the computer.
2
Press <F2> during POST to enter the system setup program.
3
Navigate to the main tab and enter the Service Tag in the Service Tag Setting field.
System Board
|
53
54
|
System Board
15
Thermal-Cooling Assembly
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 7. For additional safety best practices information, see the Regulatory
Compliance Homepage at dell.com/regulatory_compliance.
Removing the Thermal-Cooling Assembly
Prerequisites
1
Remove the battery. See "Removing the Battery" on page 13.
2
Remove the base cover. See "Removing the Base Cover" on page 17.
3
Remove the memory module(s). See "Removing the Memory Module(s)" on
page 19.
4
Follow the instructions from step 1 to step 3 in "Removing the Hard Drive" on
page 21.
5
Follow the instructions from step 1 to step 2 in "Removing the Optical Drive" on
page 25.
6
Remove the keyboard. See "Removing the Keyboard" on page 15.
7
Remove the palm rest. See "Removing the Palm Rest" on page 27.
8
Follow the instructions from step 1 to step 8 in "Removing the System Board" on
page 49.
Thermal-Cooling Assembly
|
55
Procedure
1
In sequential order (indicated on the thermal-cooling assembly), remove the
screws that secure the thermal-cooling assembly to the system board.
2
Lift the thermal-cooling assembly off the system board.
2
1
1 thermal-cooling assembly
56
|
2 screws (7)
Thermal-Cooling Assembly
Replacing the Thermal-Cooling Assembly
Procedure
1
Align the screw holes on the thermal-cooling assembly with the screw holes on the
system board.
2
In sequential order (indicated on the thermal-cooling assembly), replace screws
that secure the thermal-cooling assembly to the system board.
Postrequisites
1
Follow the instructions from step 3 to step 10 in "Replacing the System Board" on
page 52.
2
Replace the palm rest. See "Replacing the Palm Rest" on page 31.
3
Replace the keyboard. See "Replacing the Keyboard" on page 16.
4
Follow the instructions from step 4 to step 5 in "Replacing the Optical Drive" on
page 26.
5
Follow the instructions from step 4 to step 6 in "Replacing the Hard Drive" on
page 23.
6
Replace the memory module(s). See "Replacing the Memory Module(s)" on
page 20.
7
Replace the base cover. See "Replacing the Base Cover" on page 18.
8
Replace the battery. See "Replacing the Battery" on page 13.
9
Follow the instructions in "After Working Inside Your Computer" on page 9.
Thermal-Cooling Assembly
|
57
58
|
Thermal-Cooling Assembly
16
Processor
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 7. For additional safety best practices information, see the Regulatory
Compliance Homepage at dell.com/regulatory_compliance.
Removing the Processor
Prerequisites
1
Remove the battery. See "Removing the Battery" on page 13.
2
Remove the base cover. See "Removing the Base Cover" on page 17.
3
Remove the memory module(s). See "Removing the Memory Module(s)" on
page 19.
4
Follow the instructions from step 1 to step 3 in "Removing the Hard Drive" on
page 21.
5
Follow the instructions from step 1 to step 2 in "Removing the Optical Drive" on
page 25.
6
Remove the keyboard. See "Removing the Keyboard" on page 15.
7
Remove the palm rest. See "Removing the Palm Rest" on page 27.
8
Follow the instructions from step 1 to step 8 in "Removing the System Board" on
page 49.
9
Remove the thermal-cooling assembly. See "Removing the Thermal-Cooling
Assembly" on page 55.
Processor
|
59
Procedure
1
To loosen the ZIF socket, use a small, flat-blade screwdriver and rotate the
ZIF-socket cam screw counterclockwise until it comes to the cam stop.
CAUTION: To ensure maximum cooling for the processor, do not touch the heat
transfer areas on the processor thermal cooling assembly. The oils in your skin
can reduce the heat transfer capability of the thermal pads.
CAUTION: When removing the processor module, pull the module straight up.
Be careful not to bend the pins on the processor module.
2
Lift the processor module from the ZIF socket.
4
1
2
3
1
processor
2
ZIF socket
3
pin-1 corner
4
ZIF-socket cam screw
60
|
Processor
Replacing the Processor
Procedure
NOTE: If you install a new processor, a new thermal cooling assembly including an
affixed thermal pad or a new thermal pad along with documentation to illustrate
proper installation is shipped.
1
Align the pin-1 corner of the processor module with the pin-1 corner of the ZIF
socket, then insert the processor module.
NOTE: The pin-1 corner of the processor module has a triangle that aligns with the
triangle on the pin-1 corner of the ZIF socket.
When the processor module is properly seated, all four corners are aligned at the
same height. If one or more corners of the module are higher than the others, the
module is not seated properly.
CAUTION: To avoid damage to the processor, hold the screwdriver perpendicular
to the processor when turning the cam screw.
2
Tighten the ZIF socket by turning the cam screw clockwise to secure the processor
module to the system board.
Postrequisites
1
Replace the thermal-cooling assembly. See "Replacing the Thermal-Cooling
Assembly" on page 57.
2
Follow the instructions from step 3 to step 10 in "Replacing the System Board" on
page 52.
3
Replace the palm rest. See "Replacing the Palm Rest" on page 31.
4
Replace the keyboard. See "Replacing the Keyboard" on page 16.
5
Follow the instructions from step 4 to step 5 in "Replacing the Optical Drive" on
page 26.
6
Follow the instructions from step 4 to step 6 in "Replacing the Hard Drive" on
page 23.
7
Replace the memory module(s). See "Replacing the Memory Module(s)" on
page 20.
8
Replace the base cover. See "Replacing the Base Cover" on page 18.
9
Replace the battery. See "Replacing the Battery" on page 13.
10
Follow the instructions in "After Working Inside Your Computer" on page 9.
Processor
|
61
62
|
Processor
17
Coin-Cell Battery
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 7. For additional safety best practices information, see the Regulatory
Compliance Homepage at dell.com/regulatory_compliance.
WARNING: The battery may explode if installed incorrectly. Replace the battery
only with the same or equivalent type. Discard used batteries according to the
manufacturer’s instructions.
Removing the Coin-Cell Battery
CAUTION: Removing the coin-cell battery resets the BIOS settings to default. It is
recommended that you note the BIOS settings before removing the coin-cell
battery.
Prerequisites
1
Remove the battery. See "Removing the Battery" on page 13.
2
Remove the base cover. See "Removing the Base Cover" on page 17.
3
Remove the memory module(s). See "Removing the Memory Module(s)" on
page 19.
4
Follow the instructions from step 1 to step 3 in "Removing the Hard Drive" on
page 21.
5
Follow the instructions from step 1 to step 2 in "Removing the Optical Drive" on
page 25.
6
Remove the keyboard. See "Removing the Keyboard" on page 15.
7
Remove the palm rest. See "Removing the Palm Rest" on page 27.
8
Follow the instructions from step 1 to step 8 in "Removing the System Board" on
page 49.
Coin-Cell Battery
|
63
Procedure
Using a plastic scribe, gently pry the coin-cell battery out of the battery socket on the
system board.
3
2
1
1
battery socket
3
plastic scribe
64
|
Coin-Cell Battery
2 coin-cell battery
Replacing the Coin-Cell Battery
Procedure
With the positive-side facing up, snap the coin-cell battery into the battery socket on the
system board.
Postrequisites
1
Follow the instructions from step 3 to step 10 in "Replacing the System Board" on
page 52.
2
Replace the palm rest. See "Replacing the Palm Rest" on page 31.
3
Replace the keyboard. See "Replacing the Keyboard" on page 16.
4
Follow the instructions from step 4 to step 5 in "Replacing the Optical Drive" on
page 26.
5
Follow the instructions from step 4 to step 6 in "Replacing the Hard Drive" on
page 23.
6
Replace the memory module(s). See "Replacing the Memory Module(s)" on
page 20.
7
Replace the base cover. See "Replacing the Base Cover" on page 18.
8
Replace the battery. See "Replacing the Battery" on page 13.
9
Follow the instructions in "After Working Inside Your Computer" on page 9.
Coin-Cell Battery
|
65
66
|
Coin-Cell Battery
18
Speakers
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 7. For additional safety best practices information, see the Regulatory
Compliance Homepage at dell.com/regulatory_compliance.
Removing the Speakers
Prerequisites
1
Remove the battery. See "Removing the Battery" on page 13.
2
Remove the base cover. See "Removing the Base Cover" on page 17.
3
Remove the memory module(s). See "Removing the Memory Module(s)" on
page 19.
4
Follow the instructions from step 1 to step 3 in "Removing the Hard Drive" on
page 21.
5
Follow the instructions from step 1 to step 2 in "Removing the Optical Drive" on
page 25.
6
Remove the keyboard. See "Removing the Keyboard" on page 15.
7
Remove the palm rest. See "Removing the Palm Rest" on page 27.
8
Follow the instructions from step 1 to step 8 in "Removing the System Board" on
page 49.
Speakers
|
67
Procedure
1
Remove the screws that secure the speakers to the computer base.
2
Lift the speakers along with its cable away from the computer base.
2
1
1 screws (4)
68
|
Speakers
2
speakers
Replacing the Speakers
Procedure
1
Align the screw holes on the speakers with the screw holes on the computer base
and place the speakers on the computer base.
2
Replace the screws that secure the speakers to the computer base.
Postrequisites
1
Follow the instructions from step 3 to step 10 in "Replacing the System Board" on
page 52.
2
Replace the palm rest. See "Replacing the Palm Rest" on page 31.
3
Replace the keyboard. See "Replacing the Keyboard" on page 16.
4
Follow the instructions from step 4 to step 5 in "Replacing the Optical Drive" on
page 26.
5
Follow the instructions from step 4 to step 6 in "Replacing the Hard Drive" on
page 23.
6
Replace the memory module(s). See "Replacing the Memory Module(s)" on
page 20.
7
Replace the base cover. See "Replacing the Base Cover" on page 18.
8
Replace the battery. See "Replacing the Battery" on page 13.
9
Follow the instructions in "After Working Inside Your Computer" on page 9.
Speakers
|
69
70
|
Speakers
19
Media Card Reader
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 7. For additional safety best practices information, see the Regulatory
Compliance Homepage at dell.com/regulatory_compliance.
Removing the Media Card Reader
Prerequisites
1
Remove the battery. See "Removing the Battery" on page 13.
2
Remove the base cover. See "Removing the Base Cover" on page 17.
3
Remove the memory module(s). See "Removing the Memory Module(s)" on
page 19.
4
Follow the instructions from step 1 to step 3 in "Removing the Hard Drive" on
page 21.
5
Follow the instructions from step 1 to step 2 in "Removing the Optical Drive" on
page 25.
6
Remove the keyboard. See "Removing the Keyboard" on page 15.
7
Remove the palm rest. See "Removing the Palm Rest" on page 27.
8
Follow the instructions from step 1 to step 8 in "Removing the System Board" on
page 49.
9
Remove the speakers. See "Removing the Speakers" on page 67.
Media Card Reader
|
71
Procedure
1
Remove the screw that secures the Media Card Reader to the computer base.
2
Make note of the Media Card Reader cable routing.
3
Lift the Media Card Reader along with its cable away from the computer base.
2
1
1 Media Card Reader
72
|
2 screw
Media Card Reader
Replacing the Media Card Reader
Procedure
1
Align the screw holes on the Media Card Reader with the screw holes on the
computer base and place the Media Card Reader on the computer base.
2
Replace the screw that secures the Media Card Reader to the computer base.
Postrequisites
1
Replace the speakers. See "Replacing the Speakers" on page 69.
1
Follow the instructions from step 3 to step 10 in "Replacing the System Board" on
page 52.
2
Replace the palm rest. See "Replacing the Palm Rest" on page 31.
3
Replace the keyboard. See "Replacing the Keyboard" on page 16.
4
Follow the instructions from step 4 to step 5 in "Replacing the Optical Drive" on
page 26.
5
Follow the instructions from step 4 to step 6 in "Replacing the Hard Drive" on
page 23.
6
Replace the memory module(s). See "Replacing the Memory Module(s)" on
page 20.
7
Replace the base cover. See "Replacing the Base Cover" on page 18.
8
Replace the battery. See "Replacing the Battery" on page 13.
9
Follow the instructions in "After Working Inside Your Computer" on page 9.
Media Card Reader
|
73
74
|
Media Card Reader
20
Daughter Board
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 7. For additional safety best practices information, see the Regulatory
Compliance Homepage at dell.com/regulatory_compliance.
Removing the Daughter Board
Prerequisites
1
Remove the battery. See "Removing the Battery" on page 13.
2
Remove the base cover. See "Removing the Base Cover" on page 17.
3
Remove the memory module(s). See "Removing the Memory Module(s)" on
page 19.
4
Follow the instructions from step 1 to step 3 in "Removing the Hard Drive" on
page 21.
5
Follow the instructions from step 1 to step 2 in "Removing the Optical Drive" on
page 25.
6
Remove the keyboard. See "Removing the Keyboard" on page 15.
7
Remove the palm rest. See "Removing the Palm Rest" on page 27.
8
Remove the Mini-Card. See "Removing the Mini-Card" on page 79.
9
Remove the display assembly. See "Removing the Display Assembly" on page 35.
10
Follow the instructions from step 1 to step 8 in "Removing the System Board" on
page 49.
Daughter Board
|
75
Procedure
1
Remove the screws that secure the daughter board to the computer base.
2
Lift the daughter board away from the computer base.
2
1
1 daughter board
76
|
Daughter Board
2 screws (4)
Replacing the Daughter Board
Procedure
1
Align the screw holes on the daughter board with the screw holes on the computer
base.
2
Replace the screws that secure the daughter board to the computer base.
Postrequisites
1
Replace the display assembly. See "Replacing the Display Assembly" on page 37.
2
Follow the instructions from step 3 to step 10 in "Replacing the System Board" on
page 52.
3
Replace the Mini-Card. See "Replacing the Mini-Card" on page 80.
4
Replace the palm rest. See "Replacing the Palm Rest" on page 31.
5
Replace the keyboard. See "Replacing the Keyboard" on page 16.
6
Follow the instructions from step 4 to step 5 in "Replacing the Optical Drive" on
page 26.
7
Follow the instructions from step 4 to step 6 in "Replacing the Hard Drive" on
page 23.
8
Replace the memory module(s). See "Replacing the Memory Module(s)" on
page 20.
9
Replace the base cover. See "Replacing the Base Cover" on page 18.
10
Replace the battery. See "Replacing the Battery" on page 13.
11
Follow the instructions in "After Working Inside Your Computer" on page 9.
Daughter Board
|
77
78
|
Daughter Board
21
Mini-Card
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 7. For additional safety best practices information, see the Regulatory
Compliance Homepage at dell.com/regulatory_compliance.
NOTE: Dell does not guarantee compatibility or provide support for Mini-Cards
from sources other than Dell.
If you ordered a wireless Mini-Card with your computer, the card is already installed.
Your computer has one half Mini-Card slot which supports a Wireless Local Area
Network (WLAN) + Bluetooth combo card, Wi-Fi, and Worldwide Interoperability for
Microwave Access (WiMax) cards.
Removing the Mini-Card
Prerequisites
1
Remove the battery. See "Removing the Battery" on page 13.
2
Remove the keyboard. See "Removing the Keyboard" on page 15.
3
Remove the base cover. See "Removing the Base Cover" on page 17.
4
Remove the palm rest. See "Removing the Palm Rest" on page 27.
Procedure
1
Disconnect the antenna cables from the connectors on the Mini-Card.
2
Remove the screw that secures the Mini-Card to the connector on the daughter
board.
1
2
3
1
screw
3
antenna cables (2)
2
Mini-Card
Mini-Card
|
79
3
Lift the Mini-Card out of the connector on the daughter board.
CAUTION: When the Mini-Card is not in the computer, store it in protective
antistatic packaging. For more information, see "Protecting Against Electrostatic
Discharge" in the safety information that shipped with your computer.
Replacing the Mini-Card
Procedure
1
Remove the new Mini-Card from its packaging.
2
Align the notch on the Mini-Card with the tab on the connector on the daughter
board.
CAUTION: Use firm and even pressure to slide the Mini-Card into place. If you use
excessive force, you may damage the connector.
CAUTION: The connectors are keyed to ensure correct insertion. If you feel
resistance, check the connectors on the Mini-Card and on the daughter board,
and realign the Mini-Card.
CAUTION: To avoid damage to the Mini-Card, never place cables under the
wireless Mini-Card.
3
80
Insert the Mini-Card connector at a 45-degree angle into the connector on the
daughter board.
|
Mini-Card
4
Press the other end of the Mini-Card down into the slot on the daughter board and
replace the screw that secures the Mini-Card to the daughter board.
5
Connect the antenna cables to the connectors on the Mini-Card.
The following table provides the wireless antenna cable color scheme for the
Mini-Cards supported by your computer.
Connectors on the Mini-Card
Antenna Cable Color Scheme
WLAN + Bluetooth (2 cables)
Main WLAN + Bluetooth (white triangle)
white
Auxiliary WLAN + Bluetooth
(black triangle)
black
WWAN (2 antenna cables)
Main WWAN (white triangle)
white
Auxiliary WWAN (black triangle)
black
Postrequisites
1
Replace the palm rest. See "Replacing the Palm Rest" on page 31.
2
Replace the base cover. See "Replacing the Base Cover" on page 18.
3
Replace the keyboard. See "Replacing the Keyboard" on page 16.
4
Replace the battery. See "Replacing the Battery" on page 13.
5
Follow the instructions in "After Working Inside Your Computer" on page 9.
Mini-Card
|
81
82
|
Mini-Card
22
Flashing the BIOS
The BIOS may require flashing when an update is available or when
replacing the system board.
To flash the BIOS:
1
Turn on the computer.
2
Go to support.dell.com/support/downloads.
3
Locate the BIOS update file for your computer:
NOTE: The Service Tag for your computer is located on a label at the bottom
of your computer. For more information, see the Quick Start Guide that
shipped with your computer.
If you have your computer’s Service Tag or Express Service Code:
a
Enter your computer’s Service Tag or Express Service Code in the Service Tag
or Express Service Code field.
b
Click Submit and proceed to step 4.
If you do not have your computer’s Service Tag or Express Service Code:
a
b
Select one of the following options:
•
Automatically detect my Service Tag for me
•
Choose from My Products and Services List
•
Choose from a list of all Dell products
Click Continue and follow the instructions on the screen.
4
A list of results appears on the screen. Click BIOS.
5
Click Download File to download the latest BIOS file.
6
In the Please select your download method below window, click
For Single File Download via Browser, and then click Download Now.
7
In the Save As window, select an appropriate location to download the file on your
computer.
8
If the Download Complete window appears, click Close.
9
Navigate to the folder where you downloaded the BIOS update file.
The file icon appears in the folder and is titled the same as the downloaded BIOS
update file.
10
Double-click the BIOS update file icon and follow the instructions that appear on
the screen.
Flashing the BIOS
|
83
84
|
Flashing the BIOS
Dell Inspiron 7520
Описание
ф мл ни
дит
нл н з 2 мин ты
Характеристики
Д т в
в
м
з
нии
з в
ии
Д т в
и
Аксессуары
гл
л жб
т чн я
дд ж и
л т
вин и
л т з з любым
д бным
б м
тзывы
ции и
ид и
Download PDF