Cisco | WS-X4013 - Supervisor Engine II-Plus-TS | Specifications | Cisco WS-X4013 - Supervisor Engine II-Plus-TS Specifications

Installation and Configuration Note for the
Catalyst 4500 Series Supervisor Engine II-Plus TS
Product Numbers: WS-X4013+TS = Catalyst 4500 Series Supervisor Engine II-Plus TS
This publication describes how to install and verify the operation of the Catalyst 4500 series switch
Supervisor Engine II-Plus TS. Refer to the software configuration guide for your switch to obtain
configuration information for the supervisor engines and switching modules.
Contents
This document contains these sections:
•
Safety Overview, page 2
•
Supervisor Engine II-Plus TS, page 7
•
Port Cabling Specifications, page 10
•
Installing and Removing the Supervisor Engine, page 11
•
Attaching Module Interface Cables, page 15
•
Configuring Your Supervisor Engine, page 16
•
SFP Guidelines, page 16
•
Standards Compliance Specifications, page 20
•
Related Documentation, page 20
•
Obtaining Documentation, page 21
•
Obtaining Technical Assistance, page 22
•
Obtaining Additional Publications and Information, page 23
Corporate Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Copyright © 2004 Cisco Systems, Inc. All rights reserved.
Safety Overview
Safety Overview
Throughout this publication, safety warnings appear in procedures that may harm you if performed
incorrectly. A warning symbol precedes each warning statement.
Warning
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents. Use the statement number provided at the end of
each warning to locate its translation in the translated safety warnings that accompanied this
device. Statement 1071
SAVE THESE INSTRUCTIONS
Waarschuwing
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan
veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij
elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard
praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de
waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt
raadplegen.
BEWAAR DEZE INSTRUCTIES
Varoitus
TÄRKEITÄ TURVALLISUUSOHJEITA
Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin
käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu
onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen
mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien
lausuntonumeroiden avulla.
SÄILYTÄ NÄMÄ OHJEET
Attention
IMPORTANTES INFORMATIONS DE SÉCURITÉ
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant
entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez
conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures
couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des
avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil,
référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.
CONSERVEZ CES INFORMATIONS
Installation and Configuration Note for the Catalyst 4500 Series Supervisor Engine II-Plus TS
2
78-16551-01
Safety Overview
Warnung
WICHTIGE SICHERHEITSHINWEISE
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen
kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und
den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder
Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten
Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.
BEWAHREN SIE DIESE HINWEISE GUT AUF.
Avvertenza
IMPORTANTI ISTRUZIONI SULLA SICUREZZA
Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle
persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli
relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti.
Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le
traduzioni delle avvertenze riportate in questo documento.
CONSERVARE QUESTE ISTRUZIONI
Advarsel
VIKTIGE SIKKERHETSINSTRUKSJONER
Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du
begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med
elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten
av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne
enheten.
TA VARE PÅ DISSE INSTRUKSJONENE
Aviso
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de
lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos
perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de
prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para
localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.
GUARDE ESTAS INSTRUÇÕES
¡Advertencia!
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular
cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los
procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el
número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña
a este dispositivo.
GUARDE ESTAS INSTRUCCIONES
Installation and Configuration Note for the Catalyst 4500 Series Supervisor Engine II-Plus TS
78-16551-01
3
Safety Overview
Varning!
VIKTIGA SÄKERHETSANVISNINGAR
Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada.
Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och
känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av
varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna
anordning.
SPARA DESSA ANVISNINGAR
Installation and Configuration Note for the Catalyst 4500 Series Supervisor Engine II-Plus TS
4
78-16551-01
Safety Overview
Aviso
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões
corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os
circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o
número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de
segurança traduzidos que acompanham o dispositivo.
GUARDE ESTAS INSTRUÇÕES
Advarsel
VIGTIGE SIKKERHEDSANVISNINGER
Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for
legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de
involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til
undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de
oversatte advarsler, der fulgte med denne enhed.
GEM DISSE ANVISNINGER
Installation and Configuration Note for the Catalyst 4500 Series Supervisor Engine II-Plus TS
78-16551-01
5
Safety Overview
Installation and Configuration Note for the Catalyst 4500 Series Supervisor Engine II-Plus TS
6
78-16551-01
Supervisor Engine II-Plus TS
Supervisor Engine II-Plus TS
This section describes the Catalyst 4500 series Supervisor Engine II-Plus TS (WS-X4013+ TS). This
supervisor engine provides data path and data control for all network interfaces, and also provides
12 10/100/1000BASE-T IEEE 802.3af compliant Power over Ethernet (PoE) ports and 8 1000BASE-X
SFP ports. A PoE-capable power supply is not needed to use PoE devices connected to the front panel
ports on the Catalyst 4500 series Supervisor Engine II-Plus TS. A PoE-capable power supply would be
needed to use PoE devices connected to modules in slot 2 and slot 3.
The Catalyst 4500 series Supervisor Engine II-Plus TS is only used in Catalyst 4503 switches. Install
the Catalyst 4500 series Supervisor Engine II-Plus TS in slot 1.
The supervisor engine is hot swappable, but packets are not forwarded when the supervisor engine has
been removed. When a supervisor engine is reinserted, the system reboots.
The Catalyst 4500 series Supervisor Engine II-Plus TS provides:
•
64-Gbps full-duplex switching, with an actual forwarding rate of 48 million packets-per-second
•
32K MAC addresses for Layer 2 switching
•
16K IP unicast adjacencies
•
2048 VLANs with 802.1Q VLAN tagging on all ports
•
Cisco Inter Switch Link (ISL) tagging on all ports
•
Support for Jumbo Frames on all non-blocking GE ports
Installation and Configuration Note for the Catalyst 4500 Series Supervisor Engine II-Plus TS
78-16551-01
7
Supervisor Engine II-Plus TS
Figure 1
Catalyst 4500 Series Supervisor Engine II-Plus TS (WS-X4013+TS)
RESET button
Switch load
indicators
Compact Flash port
Ethernet
management port
CONSOLE
port
113860
STATUS LED
PoE status
LED
The supervisor engine includes interfaces for SNMP, console, and Telnet and provides management
functions such as environmental status monitoring.
There is a total of 158.4 Watts available for PoE. This allows any eight ports to be compliant to IEEE
802.3af with 15.4 Watts of supplied power, while the other four ports provide 6.3 Watts of supplied power.
The Catalyst 4500 series Supervisor Engine II-Plus TS has a standard serial console and a
10/100BASE-TX Ethernet management port.
The following sections describe the LEDs, connectors, and switches on the Catalyst 4500 series
Supervisor Engine II-Plus TS:
•
LEDs, page 9
•
SFP Ports, page 9
•
10/100/1000 Ports, page 9
•
Ethernet Management Port, page 9
•
Console Port, page 10
•
RESET Button, page 10
•
Flash Port, page 10
Installation and Configuration Note for the Catalyst 4500 Series Supervisor Engine II-Plus TS
8
78-16551-01
Supervisor Engine II-Plus TS
LEDs
Table 1 describes the LEDs on the supervisor engine front panel.
Table 1
Supervisor Engine LEDs (WS-X4013+TS)
LED
LED Status
STATUS
UTILIZATION
Indicates the results of a series of self-tests.
Green
All diagnostic tests passed.
Red
A test failed.
Orange
System boot or diagnostic test is in progress.
Off
Module is disabled.
Green 1–100%
If the switch is operational, this display indicates the
current traffic load over the backplane (as an approximate
percentage).
Link
PoE Status
Description
Indicates the status of the 10/100BASE-T Ethernet
management port or uplink ports.
Green
The link is operational.
Orange
The link is disabled by user.
Flashing orange
The power-on self-test indicates a faulty port.
Off
No signal is detected, or there is a link configuration
failure.
Green
PoE is healthy.
Off
No PoE power is available.
Red
One or more ports are in power-deny mode.
SFP Ports
The Gigabit Ethernet SFP ports operate in full-duplex mode only. These ports use the 1000BASE-SX,
1000BASE-LX, Cisco Coarse Wave Division Multiplexing (CWDM ) SFPs, 1000BASE-T SFP, and
1000BASE-ZX SFP. SFP connectors vary with interface type and may use multimode fiber (MMF),
single-mode fiber (SMF) cable, or copper Ethernet cables. For further information on SFPs, see the “SFP
Guidelines” section on page 16.
10/100/1000 Ports
The 10/100/1000 ports operate in full-duplex mode or in half-duplex mode. These ports use RJ-45
connectors.
Ethernet Management Port
The Ethernet management port is used (in ROMMON mode only) to recover a switch software image
that has been corrupted or destroyed. This port is not active while the switch is operating normally.
Installation and Configuration Note for the Catalyst 4500 Series Supervisor Engine II-Plus TS
78-16551-01
9
Port Cabling Specifications
Console Port
The Catalyst 4500 series Supervisor Engine II-Plus TS console port has an EIA/TIA-232 RJ-45
connector. The console port allows you to perform the following functions:
Note
•
Configure the switch from the CLI
•
Monitor network statistics and errors
•
Configure SNMP agent parameters
EIA/TIA-232 was known as recommended standard RS-232 before its acceptance as a standard by the
Electronic Industries Alliance (EIA) and Telecommunications Industry Association (TIA).
RESET Button
The RESET button is used to restart the switch.
Note
Use a paper clip or other small, pointed object to press the RESET button.
Flash Port
The Flash port accepts a Type 1 compact Flash card. You can use it for file transfer tasks such as loading
a new software image. The Flash card is optional and can be obtained from Cisco resellers or directly
from Cisco.
For more information, refer to Using the Compact Flash on the Catalyst 4000 Family Supervisor
Engine III and IV at the following URL:
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat4000/inst_nts/ol_2058.htm
Port Cabling Specifications
This section provides port cabling specifications.
The length of your networks and the distances between connections depend on the type of signal, the
signal speed, and the transmission medium (the type of cabling used to transmit the signals). The
distance and rate limits in this document are the IEEE-recommended maximum speeds and distances for
signaling. Table 2 shows the transmission speed versus the distance.
Table 2
EIA/TIA-232 Transmission Speed in Contrast with Distance
Rate (bps)
Distance (ft)
Distance (m)
2400
200
60
4800
100
30
9600
50
15
19,200
25
7.6
38,400
12
3.7
56,000
8.6
2.6
Installation and Configuration Note for the Catalyst 4500 Series Supervisor Engine II-Plus TS
10
78-16551-01
Installing and Removing the Supervisor Engine
Maximum Cable Distances
Table 3 shows the maximum cable distances for transceiver speed and cable type.
Table 3
Maximum Cable Distances
Transceiver
Speed
Cable Type
Duplex Mode
Maximum Distance
Between Stations
10 Mbps
Category 3 UTP
Half or full
328 ft (100 m)
10 Mbps
MMF
Half or full
1.2 mi (2 km)
100 Mbps
Category 5 UTP
Half or full
328 ft (100 m)
100 Mbps
MMF
Half
1312 ft (400 m)
100 Mbps
MMF
Full
1.2 mi (2 km)
Table 4 on page 17 provides cabling specifications for the SFPs that you install in the SFP port modules.
Installing and Removing the Supervisor Engine
Warning
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Statement 1030
All Catalyst 4500 series switches support hot swapping, which lets you install, remove, replace, and
rearrange supervisor engines and switching modules without powering off the system. When the system
detects that a switching module has been installed or removed, it runs diagnostic and discovery routines
automatically, acknowledges the presence or absence of the module, and resumes system operation with
no operator intervention.
This section contains the following subsections:
•
Required Tools, page 11
•
Installing the Supervisor Engine, page 12
•
Removing the Supervisor Engine, page 13
Required Tools
You will need these tools to install a supervisor engine in a Catalyst 4500 series switch:
Note
•
Number 1 and number 2 Phillips screwdrivers for the captive installation screws on most modules
•
3/16-inch flat-blade screwdriver for the captive installation screws on other modules
•
Antistatic mat or antistatic foam
•
Wrist strap or other grounding device
Whenever you handle supervisor engines, use a wrist strap or other grounding device to prevent ESD
damage.
Installation and Configuration Note for the Catalyst 4500 Series Supervisor Engine II-Plus TS
78-16551-01
11
Installing and Removing the Supervisor Engine
Installing the Supervisor Engine
The Catalyst 4500 series Supervisor Engine II-Plus TS is only used in Catalyst 4503 switches. Install
the Catalyst 4500 series Supervisor Engine II-Plus TS in slot 1.
Warning
Caution
Hazardous voltage or energy is present on the backplane when the system is operating. Use caution
when servicing. Statement 1034
To prevent ESD damage, handle supervisor engines by the carrier edges only.
To install a supervisor engine in a Catalyst 4503 switch, follow this procedure:
Step 1
Take the necessary precautions to prevent ESD damage.
Step 2
Ensure that you have enough clearance to accommodate any interface equipment that you will connect
directly to the supervisor engine ports.
Step 3
Loosen the captive installation screws that secure the switching-module filler plate or the existing
supervisor engine (whichever is present), and remove it.
Step 4
Remove the supervisor engine filler plate or the existing supervisor engine from slot 1. If a switching
module filler plate was installed, save it for future use. If you are removing an existing supervisor engine,
see the “Removing the Supervisor Engine” section on page 13.
Step 5
To install the new supervisor engine, grasp the switching module front panel with one hand and place
your other hand under the carrier to support the supervisor engine, as shown in Figure 2. Do not touch
the printed circuit boards or connector pins.
Step 6
Align the edges of the supervisor engine carrier with the slot guides on the sides of the switch chassis,
as shown in Figure 2.
Figure 2
Installing the Supervisor Engine in the Chassis
4506
1
1
13
1
13
113861
1
13
13
Step 7
Pivot the two module ejector levers out and away from the faceplate.
Step 8
Carefully slide the supervisor engine into the slot until the notches on both ejector levers engage the
chassis sides.
Installation and Configuration Note for the Catalyst 4500 Series Supervisor Engine II-Plus TS
12
78-16551-01
Installing and Removing the Supervisor Engine
Step 9
Using the thumb and forefinger of each hand, simultaneously pivot in both ejector levers to fully seat the
supervisor engine in the backplane connector.
Caution
Always use the ejector levers when installing or removing a supervisor engine. A supervisor engine that
is partially seated in the backplane will not function correctly.
Step 10
Use a screwdriver to tighten the captive installation screws on each end of the supervisor engine
faceplate.
To check the status of the module, perform these steps:
Step 1
Ensure that the LED labeled Status is green (module operational).
Step 2
When the switch is online, enter the show module command. Verify that the system acknowledges the
new module and that the module status is good.
Step 3
If the module is not operational, reseat it. If the module is still not operational, contact your customer
service representative.
Removing the Supervisor Engine
Warning
Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into
beams or view directly with optical instruments. Statement 1051
Warning
Hazardous voltage or energy is present on the backplane when the system is operating. Use caution
when servicing. Statement 1034
Caution
To prevent ESD damage, handle supervisor engines by the carrier edges only.
To remove a supervisor engine from a Catalyst 4500 series switch, perform these steps:
Step 1
Disconnect any network interface cables attached to the ports on the supervisor engine that you intend
to remove.
Step 2
Loosen the captive installation screws. (See Figure 3.)
Installation and Configuration Note for the Catalyst 4500 Series Supervisor Engine II-Plus TS
78-16551-01
13
Installing and Removing the Supervisor Engine
Figure 3
Captive Installation Screws and Ejector Levers
Ejector lever
113862
Captive
installation
screw
Step 3
Grasp the left and right ejector levers, and simultaneously pivot the levers outward to release the
supervisor engine from the backplane connector. Figure 3 shows a close-up of the right ejector lever.
Step 4
Grasp the front panel of the supervisor engine with one hand, and place your other hand under the carrier
to support and guide it out of the slot. Do not touch the printed circuit boards or connector pins.
Step 5
Carefully pull the supervisor engine straight out of the slot, keeping your other hand under the carrier to
guide it.
Step 6
Place the supervisor engine on an antistatic mat or antistatic foam, or immediately install it in another
slot 1 in another chassis.
Warning
Blank faceplates and cover panels serve three important functions: they prevent exposure to
hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI)
that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not
operate the system unless all cards, faceplates, front covers, and rear covers are in place.
Statement 1029
Step 7
Warning
If the slot is to remain empty, install a switching-module filler plate (part number 800-00292-01).
Ultimate disposal of this product should be handled according to all national laws and regulations.
Statement 1040
Installation and Configuration Note for the Catalyst 4500 Series Supervisor Engine II-Plus TS
14
78-16551-01
Attaching Module Interface Cables
Attaching Module Interface Cables
Figure 4 shows the connector types used to attach interface cables to the supervisor engine.
Figure 4
RJ-45 Connector
H1567a
RJ-45 (both ends)
Pin 1
Pin 8
MT-RJ Connector
14367
Figure 5
Note
Always keep caps and plugs on the fiber-optic connectors on the cable and the switch when they are not
in use.
Warning
Voltages that present a shock hazard may exist on Power over Ethernet (PoE) circuits if
interconnections are made using uninsulated exposed metal contacts, conductors, or terminals.
Avoid using such interconnection methods, unless the exposed metal parts are located within a
restricted access location and users and service people who are authorized within the restricted
access location are made aware of the hazard. A restricted access area can be accessed only
through the use of a special tool, lock and key or other means of security. Statement 1072
Warning
To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network
voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some
LAN and WAN ports both use RJ-45 connectors. Use caution when connecting cables. Statement 1021
Warning
Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into
beams or view directly with optical instruments. Statement 1051
Installation and Configuration Note for the Catalyst 4500 Series Supervisor Engine II-Plus TS
78-16551-01
15
Configuring Your Supervisor Engine
Configuring Your Supervisor Engine
For information and commands to configure your supervisor engine, refer to the Software Configuration
Guide for your switch.
SFP Guidelines
SFP modules are hot-pluggable and field-replaceable, and you can insert them into the eight SFP module
slots on the front panel of the Supervisor Engine II+TS. You can use the SFP modules for connections
to other network devices.
You can use any combination of supported SFP modules. Use only Cisco SFP modules on your Cisco
device. Each SFP module has an internal serial EEPROM that is encoded with security information. This
encoding provides a way for Cisco to identify and validate that the SFP module meets the requirements
for the device.
The following SFP media types are supported:
•
1000BASE-SX (GLC-SX-MM)
•
1000BASE-LX/LH (GLC-LH-SM)
•
1000BASE-ZX (GLC-ZX-SM)
•
1000BASE-T (GLC-T)
•
CWDM (CWDM-SFP-xxxx)
Cisco 1000BASE-LX/LH interfaces fully comply with the IEEE 802.3z 1000BASE-LX standard.
However, their higher optical quality allows them to reach 6.2 miles (10 km) over SMF cable instead of
the 3.1 miles (5 km) specified in the standard.
If an LX/LH SFP designed for operation on an SMF cable is directly coupled to an MMF cable, an effect
known as Differential Mode Delay (DMD) might occur. See the Catalyst 4500 Series Module
Installation Guide for more information.
This section describes the following topics:
•
Fiber-Optic SFP Modules, page 17
•
1000BASE-T SFP Modules, page 18
•
CWDM SFPs, page 18
Installation and Configuration Note for the Catalyst 4500 Series Supervisor Engine II-Plus TS
16
78-16551-01
SFP Guidelines
Fiber-Optic SFP Modules
Some fiber-optic SFP modules use LC-type connectors, as shown in Figure 6.
Caution
Protect your fiber-optic SFP modules by inserting clean dust plugs into the SFP modules after you
remove the cables. Be sure to clean the optic surfaces of the fiber-optic cables with a soft antistatic cloth
before you reconnect them to another SFP module. Avoid getting dust and other contaminants into the
optical bores, as the optics do not work correctly when obstructed with dust.
LC Fiber-Optic SFP Module
63066
Figure 6
LC SFPs provide duplex single-mode and multimode connections in supported devices. Table 4 lists the
cable specifications for fiber-optic SFP module ports.
Table 4
Fiber-Optic SFP Module Port Cabling Specifications
Core Size
(micron)
Modal
Bandwidth
(MHz/km)
Cable Distance
MMF
62.5
62.5
50.0
50.0
160
200
400
500
722 feet (220 m)
902 feet (275 m)
1640 feet (500 m)
1804 feet (550 m)
MMF1
62.5
50.0
50.0
9/10
500
400
500
—
1804 feet (550 m)
1804 feet (550 m)
1804 feet (550 m)
32,810 feet (10 km)
9/10
—
43.4 to 62 miles (70
to 100 km)2
SFP Module
Wavelength
(nanometers)
Fiber Type
1000BASE-SX
850
1000BASE-LX/LH
1300
SMF
1000BASE-ZX
1550
SMF
1. A mode-conditioning patch cord is required. Using an ordinary patch cord with MMF, 1000BASE-LX/LH SFP modules, and
a short link distance can cause transceiver saturation, resulting in an elevated bit error rate (BER). When using the LX/LH
SFP module with 62.5-micron diameter MMF, you must also install a mode-conditioning patch cord between the SFP module
and the MMF cable on both the sending and receiving ends of the link. The mode-conditioning patch cord is required for link
distances greater than 984 feet (300 m).
2. 1000BASE-ZX SFP modules can reach up to 62 miles (100 km) by using dispersion-shifted SMF or low-attenuation SMF;
the distance depends on the fiber quality, the number of splices, and the connectors.
Installation and Configuration Note for the Catalyst 4500 Series Supervisor Engine II-Plus TS
78-16551-01
17
SFP Guidelines
Note
When using shorter distances of single-mode fiber cable, you might need to insert an inline optical
attenuator in the link to avoid overloading the receiver.
When the fiber-optic cable span is less than 15.43 miles (25 km), you should insert a 5-decibel (dB) or
10-dB inline optical attenuator between the fiber-optic cable plant and the receiving port on the
1000BASE-ZX SFP module at each end of the link.
Fiber-optic SFP modules also use MT-RJ connectors, as shown in Figure 7.
MT-RJ Fiber-Optic SFP Module
87946
Figure 7
1000BASE-T SFP Modules
Copper 1000BASE-T SFP modules use RJ-45 connectors, as shown in Figure 8.
1000BASE-T Copper SFP Module
87922
Figure 8
1000BASE-T copper SFP modules used with the Catalyst 4500 series Supervisor Engine II-Plus TS
operate only in 1000BASE-T mode, or at 1000 Mbps. Copper 1000BASE-T SFP modules use standard
four twisted-pair, Category 5 cable at lengths up to 328.08 feet (100 meters).
CWDM SFPs
You can connect the CWDM SFPs to CWDM passive optical system optical add/drop multiplexer
(OADM) or multiplexer/demultiplexer plug-in modules using single-mode fiber-optic cables with
standard SC connectors. Figure 9 shows a CWDM SFP with the optical port dust plug removed.
Figure 10 shows an SC-type connector.
Installation and Configuration Note for the Catalyst 4500 Series Supervisor Engine II-Plus TS
18
78-16551-01
SFP Guidelines
Figure 9
CWDM SFP Module (Yellow-Coded CWDM-SFP-1550= Shown)
Optical bore
dust plug
Figure 10
Receive optical bore
Transmit optical bore
Color coded bale clasp
120533
C
C WD
l
L as M
N
S # s -S
/N 50 1 F
: 7 21 PO / C 14
H 01 F 7
1 R 0
2 1 3 0 2
3 4 G
4 0
5 .
6 0 1
3 0
-1
3
Color arrow on label
SC-Type Fiber-Optic Connector
Plug
Keys
Cable
Light out
of fiber
Receptacle
Key slots
13087
Tr
an
sm
itt
R
er
ec
ei
ve
r
Light into
fiber
CWDM SFPs come in eight wavelengths that range from 1470 nm to 1610 nm. Color markings on the
devices identify the wavelength to which the Gigabit Ethernet channel is mapped. Table 5 lists the
CWDM SFPs with their wavelengths and color codes.
Table 5
GBIC and SFP Wavelengths and Color Coding
SFP Product Number
Wavelength
Color Identifier
CWDM-SFP-1470=
Longwave 1470 nm laser, single mode
Gray
CWDM-SFP-1490=
Longwave 1490 nm laser, single mode
Violet
CWDM-SFP-1510=
Longwave 1510 nm laser, single mode
Blue
CWDM-SFP-1530=
Longwave 1530 nm laser, single mode
Green
CWDM-SFP-1550=
Longwave 1550 nm laser, single mode
Yellow
CWDM-SFP-1570=
Longwave 1570 nm laser, single mode
Orange
CWDM-SFP-1590=
Longwave 1590 nm laser, single mode
Red
CWDM-SFP-1610=
Longwave 1610 nm laser, single mode
Brown
Installation and Configuration Note for the Catalyst 4500 Series Supervisor Engine II-Plus TS
78-16551-01
19
Standards Compliance Specifications
Standards Compliance Specifications
When installed in a system, the Catalyst 4500 series modules comply with the standards listed in Table 6.
Table 6
Standards Compliance Specifications
Item
Specification
Compliance
CE1 Marking
Safety
UL2 60950, CSA3-C22.2 No. 60950, EN4 60950, IEC5 60950, TS0016,
AS/NZS7 3260
EMC8
FCC9 Part 15, Class A (CFR10 47) (USA), ICES11-003 Class A (Canada),
EN 55022 Class A (Europe), CISPR2212 Class A (International), AS/NZS 3548
Class A (Australia), and VCCI13 Class A (Japan) with UTP14
1. CE = European Compliance
2. UL = Underwriters Laboratory
3. CSA = Canadian Standards Association
4. EN = European Norm
5. IEC = International Electrotechnical Commission
6. TS = technical specifications
7. AS/NZS = Australia Standards/New Zealand Standards
8. EMC = electromagnetic compatibility
9. FCC = U.S. Federal Communications Commission
10. CFR = Code of Federal Regulations
11. ICES = Interference-Causing Equipment Standard
12. CISPR = Comite International Special des Perturbation Radioelectriques
13. VCCI = Voluntary Control Council for Information Technology Equipment
14. UTP = unshielded twisted-pair
The Catalyst 4500 series modules have been found to comply with the limits for a Class A digital device
per FCC (CFR 47) Part 15, ICES 003, EN55022, CISPR22, AS/NZS 3548, and VCCI with UTP cables,
and complies with the limits for a Class B digital device per EN55022, CISPR22, AS/NZS 3548, and
VCCI with shielded FTP cables.
Related Documentation
For more detailed installation and configuration information, refer to the following:
•
Catalyst 4000 Series Installation Guide
•
Catalyst 4500 Series Installation Guide
•
Catalyst 4500 Series Module Installation Guide
•
Catalyst 4500 Series Supervisor Engine and Switching Modules Installation Note
•
Cisco Small Form-Factor Pluggable Modules Installation Notes
•
Cisco CWDM GBIC and CWDM SFP Installation Note
•
Regulatory Compliance and Safety Information for the Catalyst 4500 Series Switches
Installation and Configuration Note for the Catalyst 4500 Series Supervisor Engine II-Plus TS
20
78-16551-01
Obtaining Documentation
•
Software Configuration Guide—Catalyst 4500 Series, Catalyst 2948G, and Catalyst 2980G
Switches
•
Command Reference—Catalyst 4500 Series, Catalyst 2948G, and Catalyst 2980G Switches
•
System Message Guide— Catalyst 4500 Series, Catalyst 2926G Series, Catalyst 2948G, and
Catalyst 2980G Switches
•
Layer 3 Services Software Configuration Guide
Obtaining Documentation
Cisco documentation and additional literature are available on Cisco.com. Cisco also provides several
ways to obtain technical assistance and other technical resources. These sections explain how to obtain
technical information from Cisco Systems.
Cisco.com
You can access the most current Cisco documentation at this URL:
http://www.cisco.com/univercd/home/home.htm
You can access the Cisco website at this URL:
http://www.cisco.com
You can access international Cisco websites at this URL:
http://www.cisco.com/public/countries_languages.shtml
Ordering Documentation
You can find instructions for ordering documentation at this URL:
http://www.cisco.com/univercd/cc/td/doc/es_inpck/pdi.htm
You can order Cisco documentation in these ways:
•
Registered Cisco.com users (Cisco direct customers) can order Cisco product documentation from
the Ordering tool:
http://www.cisco.com/en/US/partner/ordering/index.shtml
•
Nonregistered Cisco.com users can order documentation through a local account representative by
calling Cisco Systems Corporate Headquarters (California, USA) at 408 526-7208 or, elsewhere in
North America, by calling 800 553-NETS (6387).
Installation and Configuration Note for the Catalyst 4500 Series Supervisor Engine II-Plus TS
78-16551-01
21
Documentation Feedback
Documentation Feedback
You can send comments about technical documentation to bug-doc@cisco.com.
You can submit comments by using the response card (if present) behind the front cover of your
document or by writing to the following address:
Cisco Systems
Attn: Customer Document Ordering
170 West Tasman Drive
San Jose, CA 95134-9883
We appreciate your comments.
Obtaining Technical Assistance
For all customers, partners, resellers, and distributors who hold valid Cisco service contracts, Cisco
Technical Support provides 24-hour-a-day, award-winning technical assistance. The Cisco Technical
Support Website on Cisco.com features extensive online support resources. In addition, Cisco Technical
Assistance Center (TAC) engineers provide telephone support. If you do not hold a valid Cisco service
contract, contact your reseller.
Cisco Technical Support Website
The Cisco Technical Support Website provides online documents and tools for troubleshooting and
resolving technical issues with Cisco products and technologies. The website is available 24 hours a day,
365 days a year at this URL:
http://www.cisco.com/techsupport
Access to all tools on the Cisco Technical Support Website requires a Cisco.com user ID and password.
If you have a valid service contract but do not have a user ID or password, you can register at this URL:
http://tools.cisco.com/RPF/register/register.do
Submitting a Service Request
Using the online TAC Service Request Tool is the fastest way to open S3 and S4 service requests. (S3
and S4 service requests are those in which your network is minimally impaired or for which you require
product information.) After you describe your situation, the TAC Service Request Tool automatically
provides recommended solutions. If your issue is not resolved using the recommended resources, your
service request will be assigned to a Cisco TAC engineer. The TAC Service Request Tool is located at
this URL:
http://www.cisco.com/techsupport/servicerequest
For S1 or S2 service requests or if you do not have Internet access, contact the Cisco TAC by telephone.
(S1 or S2 service requests are those in which your production network is down or severely degraded.)
Cisco TAC engineers are assigned immediately to S1 and S2 service requests to help keep your business
operations running smoothly.
Installation and Configuration Note for the Catalyst 4500 Series Supervisor Engine II-Plus TS
22
78-16551-01
Obtaining Additional Publications and Information
To open a service request by telephone, use one of the following numbers:
Asia-Pacific: +61 2 8446 7411 (Australia: 1 800 805 227)
EMEA: +32 2 704 55 55
USA: 1 800 553 2447
For a complete list of Cisco TAC contacts, go to this URL:
http://www.cisco.com/techsupport/contacts
Definitions of Service Request Severity
To ensure that all service requests are reported in a standard format, Cisco has established severity
definitions.
Severity 1 (S1)—Your network is “down,” or there is a critical impact to your business operations. You
and Cisco will commit all necessary resources around the clock to resolve the situation.
Severity 2 (S2)—Operation of an existing network is severely degraded, or significant aspects of your
business operation are negatively affected by inadequate performance of Cisco products. You and Cisco
will commit full-time resources during normal business hours to resolve the situation.
Severity 3 (S3)—Operational performance of your network is impaired, but most business operations
remain functional. You and Cisco will commit resources during normal business hours to restore service
to satisfactory levels.
Severity 4 (S4)—You require information or assistance with Cisco product capabilities, installation, or
configuration. There is little or no effect on your business operations.
Obtaining Additional Publications and Information
Information about Cisco products, technologies, and network solutions is available from various online
and printed sources.
•
Cisco Marketplace provides a variety of Cisco books, reference guides, and logo merchandise. Visit
Cisco Marketplace, the company store, at this URL:
http://www.cisco.com/go/marketplace/
•
The Cisco Product Catalog describes the networking products offered by Cisco Systems, as well as
ordering and customer support services. Access the Cisco Product Catalog at this URL:
http://cisco.com/univercd/cc/td/doc/pcat/
•
Cisco Press publishes a wide range of general networking, training and certification titles. Both new
and experienced users will benefit from these publications. For current Cisco Press titles and other
information, go to Cisco Press at this URL:
http://www.ciscopress.com
•
Packet magazine is the Cisco Systems technical user magazine for maximizing Internet and
networking investments. Each quarter, Packet delivers coverage of the latest industry trends,
technology breakthroughs, and Cisco products and solutions, as well as network deployment and
troubleshooting tips, configuration examples, customer case studies, certification and training
information, and links to scores of in-depth online resources. You can access Packet magazine at this
URL:
http://www.cisco.com/packet
Installation and Configuration Note for the Catalyst 4500 Series Supervisor Engine II-Plus TS
78-16551-01
23
Obtaining Additional Publications and Information
•
iQ Magazine is the quarterly publication from Cisco Systems designed to help growing companies
learn how they can use technology to increase revenue, streamline their business, and expand
services. The publication identifies the challenges facing these companies and the technologies to
help solve them, using real-world case studies and business strategies to help readers make sound
technology investment decisions. You can access iQ Magazine at this URL:
http://www.cisco.com/go/iqmagazine
•
Internet Protocol Journal is a quarterly journal published by Cisco Systems for engineering
professionals involved in designing, developing, and operating public and private internets and
intranets. You can access the Internet Protocol Journal at this URL:
http://www.cisco.com/ipj
•
World-class networking training is available from Cisco. You can view current offerings at
this URL:
http://www.cisco.com/en/US/learning/index.html
This document is to be used in conjunction with the Catalyst 4500 Series Installation Guide, and the Catalyst 4500 Series Module Installation Guide publications.
CCSP, the Cisco Square Bridge logo, Follow Me Browsing, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, and iQuick
Study are service marks of Cisco Systems, Inc.; and Access Registrar, Aironet, ASIST, BPX, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, Cisco, the Cisco Certified
Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Empowering the Internet Generation,
Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step, FormShare, GigaDrive, GigaStack, HomeLink, Internet Quotient, IOS, IP/TV, iQ Expertise, the iQ logo, iQ
Net Readiness Scorecard, LightStream, Linksys, MeetingPlace, MGX, the Networkers logo, Networking Academy, Network Registrar, Packet, PIX, Post-Routing, Pre-Routing,
ProConnect, RateMUX, ScriptShare, SlideCast, SMARTnet, StrataView Plus, SwitchProbe, TeleRouter, The Fastest Way to Increase Your Internet Quotient, TransPath, and VCO
are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.
All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship
between Cisco and any other company. (0411R)
Copyright © 2004, Cisco Systems, Inc.
All rights reserved. Printed in USA.
Installation and Configuration Note for the Catalyst 4500 Series Supervisor Engine II-Plus TS
24
78-16551-01
Download PDF