XD-DV290 HRJ(N),LH(N)
SERVICE MANUAL
DVD PLAYER
BASIC DVD MECHANISM : LDM-H109
(6721R-0300A)
S/M Code No. 09-99C-337-5R3
DA
TA
RE
VI
SIO
N
This Service Manual is the “Revision Publishing” and replaces “Simple Manual”
(S/M Code No.09-99C-337-5T4).
TABLE OF CONTENTS
SPECIFICATIONS .................................................................................................................................. 3
ACCESSORIES/PACKAGE LIST ........................................................................................................... 3
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING/
Precaution to replace Optical block......................................................................................................... 4
DISASSEMBLY INSTRUCTIONS ...................................................................................................... 5-10
ELECTRICAL MAIN PARTS LIST ................................................................................................... 11-13
TRANSISTOR ILLUSTRATION ............................................................................................................ 13
BLOCK DIAGRAM-1 (OVERALL) ......................................................................................................... 14
BLOCK DIAGRAM-2 (POWER) ............................................................................................................ 15
BLOCK DIAGRAM-3 (RF/DSP/SERVO) ............................................................................................... 16
BLOCK DIAGRAM-4 (AUDIO) .............................................................................................................. 17
BLOCK DIAGRAM-5 (MPEG) ............................................................................................................... 18
BLOCK DIAGRAM-6 (SYSTEM CONTROL) ........................................................................................ 19
BLOCK DIAGRAM-7 (MIC) ................................................................................................................... 20
WIRING-1 (MAIN: COMPONENT SIDE) ........................................................................................ 21, 22
WIRING-2 (MAIN: CONDUCTOR SIDE) ........................................................................................ 23, 24
SCHEMATIC DIAGRAM-1 (MAIN 1/5) ............................................................................................ 25, 26
SCHEMATIC DIAGRAM-2 (MAIN 2/5) ............................................................................................ 27, 28
SCHEMATIC DIAGRAM-3 (MAIN 3/5) ............................................................................................ 29, 30
SCHEMATIC DIAGRAM-4 (MAIN 4/5) ............................................................................................ 31, 32
SCHEMATIC DIAGRAM-5 (MAIN 5/5) ............................................................................................ 33, 34
SCHEMATIC DIAGRAM-6 (JACK) ................................................................................................. 35, 36
WIRING-3 (JUNCTION/JACK) ........................................................................................................ 37, 38
SCHEMATIC DIAGRAM-7 (JUNCTION) ........................................................................................ 39, 40
WIRING-4 (TIMER/KEY/POWER) .................................................................................................. 41, 42
SCHEMATIC DIAGRAM-8 (TIMER/KEY) ....................................................................................... 43, 44
SCHEMATIC DIAGRAM-9 (POWER) ............................................................................................. 45, 46
SCHEMATIC DIAGRAM-10 (MIC) .................................................................................................. 47, 48
WIRING-5 (MIC) .................................................................................................................................... 49
WAVE FORM ................................................................................................................................... 50-52
TROUBLE-SHOOTING .................................................................................................................... 53-63
LCD DISPLAY ....................................................................................................................................... 64
IC DESCRIPTION ............................................................................................................................ 65-83
IC BLOCK DIAGRAM ....................................................................................................................... 84-86
MECHANICAL EXPLODED VIEW 1/1 .................................................................................................. 87
MECHANICAL PARTS LIST 1/1 ........................................................................................................... 88
MECHANISM EXPLODED VIEW 1/1 ............................................................................................. 89, 90
MECHANISM PARTS LIST 1/1 ............................................................................................................. 91
2
SPECIFICATIONS
DVD VIDEO PLAYER
Power supply
Power consumtion
Mass
External dimensions
Signal system
Laser
Frequency range (digital audio)
Signal-to-noise ratio (digital audio)
Audio dynamic range (digital audio)
Harmonic distortion(digital audio)
Wow and flutter
Operations
110~240V, 50~60Hz
20W
3.5kg(7.7lbs)
430 x 91 x 293 (W * H * D)
NTSC
Semiconductor laser, wavelength 655nm(DVD)/795nm(CD)
2Hz to 44kHz
More than 105dB (EIAJ)
More than 95dB (EIAJ)
0.003%
Below measurable level (less than +0.001%(W.PEAK)) (EIAJ)
Temperature : 5˚C(41˚F) to 35˚C(95˚F),
Operation status : Horizontal
OUTPUTS
Video outputs
S video outputs
Component video output
Audio output(digital audio)
Audio output(optical audio)
Audio output(analog audio)
•
•
1.0V(p-p), 75Ω, negative sync., RCA jack * 1
(Y)1.0V(p-p), 75Ω, negative sync.,Mini DIN 4-pin * 1
(C)0.286V(p-p), 75Ω
(Y)1.0V(p-p), 75Ω,negative sync., RCA jack * 1
(Pb)/(Pr) 0.7V(p-p), 75Ω
0.5V(p-p), 75Ω, RCA jack * 1
Optical connector * 1
2.0Vrms (1kHz, 0dB), 330Ω, RCA jack (L, R) * 2
Design and specifications are subject to change without notice .
Weight and dimensions shown are approximate.
ACCESSORIES/PACKAGE LIST
REF. NO
1
1
3
4
5
PART NO.
S8-35R-S00-09M
S8-35R-S00-09L
S5-640-17B-000
S5-640-18B-000
S7-11R-2N0-13B
5 S7-11R-2N0-13C
KANRI
NO.
DESCRIPTION
EVNT INSTRUCTION ASSY<HR<N>>
INSTRUCTION ASSY<LH<N>>
PLUG ASSY PHONE CORD 1WAY
PLUG ASSY PHONO CORD
REMOTE CONTROLLER A<LH<N>>
REMOTE CONTROLLER A<HR<N>>
3
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs laser. Therefore, be sure to follow carefully the
instructions below when servicing.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
WARNING!
WHEN SERVICING, DO NOT APPROACH THE LASER EXIT
WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO
CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE
FROM A DISTANCE OF MORE THAN 30cm FROM THE
SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL
PICK-UP BLOCK.
ATTENTION
L'utilisation de commandes, réglages ou procédures autres que
ceux spécifiés peut entraîner une dangereuse exposition aux
radiations.
ADVARSEL!
Caution: Invisible laser radiation when
open and interlocks defeated avoid exposure to beam.
Advarsel:Usynling laserståling ved åbning,
når sikkerhedsafbrydere er ude af funktion.
Undgå udsættelse for stråling.
Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude
af funktion. Undgå udsættelse for stråling.
This Compact Disc player is classified as a CLASS 1 LASER
product.
The CLASS 1 LASER PRODUCT label is located on the rear
exterior.
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saattaa altistaa käyt-täjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.
CLASS 1
KLASSE 1
LUOKAN 1
KLASS 1
VARNING!
LASER PRODUCT
LASER PRODUKT
LASER LAITE
LASER APPARAT
Om apparaten används på annat sätt än vad som specificeras i
denna bruksanvising, kan användaren utsättas för osynling
laserstrålning, som överskrider gränsen för laserklass 1.
Precaution to replace Optical block
(LPC-512A)
Body or clothes electrostatic potential could ruin
laser diode in the optical block. Be sure ground
body and workbench, and use care the clothes
do not touch the diode.
Solder
1) After the connection, remove solder shown in
the right figure.
4
DISASSEMBLY INSTRUCTIONS
CAUTION BEFORE STARTING SERVICING
Electronic parts are susceptible to static electricity and may easily damaged, so do not forget to take a proper
grounding treatment as required.
Many screws are used inside the unit. To prevent missing, dropping, etc. of the screws, always use a
magnetized screw driver in servicing. Several kinds of screws are used and some of them need special
cautions. That is, take care of the tapping screws securing molded parts and fine pitch screws used to secure
metal parts. If they are used improperly, the screw holes will be easily damaged and the parts can not be
fixed.
CABINET DISASSEMBLY
1. Top Case
3. Front Panel
1) Release 7 screws (A). (See Fig-1)
2) Lift the top case with holding the back of it, and remove
it in the direction of the arrow.
Top Case
(A)
(A)
1)
2)
3)
4)
Eject the disc tray. (See Fig-2)
Remove the tray door. (See Fig-2)
Release 2 screws (B).
Pull the front panel toward you while pressing 7
stoppers to disengage, and remove the front panel. (See
Fig-3)
(A)
(A)
(A)
(A)
(A)
(B)
Stopper
(B)
Stopper
Front Panel
Fig-1
Fig-3
2. Tray Door
1) Eject the disc tray.
2) Lift up the tray door in the direction of the arrow.
Tray Door
Disc Tray
Fig-2
5
CIRCUIT BOARD DISASSEMBLY
Note: Before removing the main circuit board, be sure to
shortcircuit the laserdiode output land.
After replacing the main circuit board, open the land after
inserting the flexible connector.
(Refer to Mechanism Disassembly)
6. TIMER and Key C.B
1) Remove the front panel. (See Fig-3)
2) Release 5 screws (E), and remove the TIMER C.B.
4. Main/JACK C.B
1) Remove the top case. (See Fig-1)
2) Release 10 screws (C), and take out the main/JACK
C.B. (See Fig-4)
3) Remove the flexible connectors and the connector from
main circuit board.
4) Then, remove the main JACK C.B.
Key C.B
(E)
(E)
(E)
(E)
(C)
(E)
(C)
JACK C.B
(C)
(C)
TIMER C.B
Main C.B
Flexible
connector
(C)
Flexible
connector
Fig-6
(C)
(C) (C)
(C)
Fig-4
5. Power C.B
1) Release 4 screws (D). (See Fig-5)
Power Code
(D)
(D)
(D)
(D)
Power C.B
Fig-5
6
DECK MECHANISM PARTS LOCATION
• Bottom View
Procedure
Parts
Starting No.
1
Junction P.C.Board
Fixing Type
4 Screws,
Disassembly Figure
Bottom
4-1
4 Locking Tabs
• Top View
2
Bracket Assembly Clamp
3
Bracket Clamp
2 Screws
4-2
4-2
4
Clamp Assembly Disk
4-2
5
Plate Clamp
4-2
5
6
Magnet Clamp
4-2
5, 6
7
Clamp Lower
2
8
Tray Disk
1 Locking Tab
4-3
2, 8
9
Base Assembly Feed
1 Connector
4-4
2, 8
10
Rubber R
1 Screw
4-4
2, 8
11
Spring Skew
1 Hook
4-4
2, 8, 11
12
Shaft PU Main
4-4
2, 8, 11
13
Shaft PU Sub
4-4
2, 8, 12, 13
14
Mechanism Assembly
4-4
2, 8, 12-14
15
Guide Freed PU
2, 8, 12-14
16
Spring Guide Feed
2, 8, 12-16
17
Pick up Assembly General
2, 8, 9
18
Motor (Mech.)
2, 8, 9
19
Shaft Lead Screw
2, 8, 9
20
Motor Assembly PU Freed 2 Locking Tabs
2, 8, 9-20
21
Base PU (Outsert)
4-4
1, 2, 8, 9
22
Base Assembly Main
4-5
1, 2, 8, 9
23
Holder Assembly Deck on 1 Locking Tab
2, 8, 9
24
Frame Assembly Up/Down
2, 8, 9
25
Rubber F
4-5
2, 8
26
Belt Loading
4-5
2, 8, 26
27
GearPulley
2, 8, 26, 27
28
Gear Loading
4-5
2, 8, 26-28
29
Gear Emergency
4-5
2, 8, 26-29
30
Cam Loading
4-5
4-2
PU Unit
1Screw
4-4
4-4
4-4
3Screws
Bottom
4-4
4-4
Bottom
Bottom
2 Locking Tabs
2 Screws
1, 2, 8, 26-31 32 Base Main
1 Locking Tab
4-5
4-5
1 Screw
1, 2, 8, 26-30 31 Motor Assembly Loading
4-4
4-5
Bottom
4-5
4-5
Note: When reassembling, perform the procedure in reverse order.
The “Bottom” on Disassembly column of above
Table indicates the part should be disassembled at the
Bottom side.
7
DECK MECHANISM ASSEMBLY
DECK ASSEMBLY
TRAY DISK
(B)
(L1)
(L2)
(L1)
EMERGENCY
EJECT HOLE
(L1)
(L1)
(C4)
(C3)
(C2)
(S1)
LEVER
JUNCTION
C.B
(C1)
(S1)
(S1)
(A)
(A)
(B)
(S1)
BOTTOM SIDE VIEW
Fig-7
Fig-9
8. Bracket Assembly Clamp (Fig-8)
BRACKET CLAMP
PLATE CLAMP
MAGNET CLAMP
CLAMP
ASSEMBLY DISK
1) Put the Deck Assembly on original position. (Top side)
2) Release 2 Screws (S2).
3) Lift up the Bracket Assembly Clamp.
(A)
8-1.
CLAMP LOWER
Clamp Assembly Disk
1) Place the Clamp Assembly Disk as Fig-(A).
2) Lift up the Clamp Assembly Disk in direction of arrow
(A).
3) Separate the Clamp Assembly Disk from the Bracket
Clamp.
(S2)
(S2)
(Fig-A)
8-1-1. Plate Clamp
1) Turn the Plate Clamp to counterclockwise direction and
then lift up the Plate Clamp.
BRACKET CLAMP
8-1-2. Magnet Clamp
8-1-3. Clamp Lower
8-2.
DECK ASSEMBLY
Bracket Clamp
9. Tray Disk (Fig-9)
1) Insert and push a Driver in the emergency eject hole (A)
at the front side, or put the Driver on the Lever (B) of
the Gear Emergency and pull the Lever (B) in direction
of arrow (A) so that the Tray Disk is ejected about 1520mm.
2) Pull the Tray Disk until the moving is locked by the
Locking Tab (L2).
3) Unlock the Locking tab (L2) in direction of arrow (B).
4) Separate the Tray Disk completely.
Fig-8
7. Junction C.B (Fig-7)
1)
2)
3)
4)
Put the Deck Assembly face down. (Bottom side)
Release 4 Screws (S1).
Unlock 4 Locking tabs (L1).
Lift up the Junction C.B a little to disconnect the
Connector (C1).
5) Disconnect 3 Connectors (C2, C3, C4).
8
CABLE FLEXIBLE
MOTOR ASSEMBLY PU FEED
BASE PU (OUTSERT)
SHAFT PU SUB
(A)
SHAFT PU MAIN
Fig-(A)
PICK UP
ASSEMBLY GENERAL
P.C. BOARD
(C5)
RED
BLACK
(S3)
SPRING
GUIDE FEED
GUIDE FEED PU
(S4)
RUBBER R
SPRING SKEW
(L4)
BASE PU (OUTSERT)
(A)
MOTOR
ASSEMBLY PU
FEED
(L3)
(A)
MOTOR (MECH.)
SHAFT LEAD SCREW
(S5)
(S5)
Fig-10
10. Base Assembly Feed (Fig-10)
10-5-3. Pick Up Assembly General
1) Disconnect the Connector (C5)
2) Release the Screw (S3).
10-6. Motor (mech.)
1) Release the 3 Screws (S5) at bottom side.
2) Push down the Motor (Mech.) and separate from the
Base PU (Outsert).
10-1. Rubber R
10-2. Spring Skew
10-7. Shaft Lead Screw
1) Press the (A) position of the Spring Skew and unlock
the Spring Skew locking.
1) Push the Shaft Lead Screw in direction on arrow (A) a
little and lift up the Shaft Lead Screw.
10-3. Shaft PU Main
10-4. Shaft PU SUB
10-8. Motor Assembly PU Feed.
10-5. Mechanism Assembly PU Unit
1) Unlock the Locking tab (L3) and lift up the P.C.Board.
2) Unlock two Locking Tabs (L4) and push down the
Motor Assembly PU Feed.
3) Separate the Motor Assembly PU Feed from the Base
PU (Outsert).
10-5-1. Guide Feed PU
1) Release the Screw (S4) and separate the Guide Feed PU
from the Pick up Assembly General.
Note: When reassembling, place the Motor Assembly PU
Feed as Fig-(A) and insert the Cable Flexible to the
Hole (A) of the Base PU (Outsert). (See Fig-(A))
Note: When reassembling, be careful not to change the
Shaft PU Main (Long) and the Shaft PU Sub (Short).
10-5-2. Spring Guide Feed
10-9. Motor (mech.)
9
(R2)
Fig-(B)
(R1)
FRAME ASSEMBLY UP/DOWN
RUBBER F
Fig-(D)
GEAR EMERGENCY
(S6)
(R1)
(R2)
GEAR PULLY
BASE MAIN
GEAR LOADING
CAM LOADING
(L6)
(S7)
(L7)
HOLDER
ASSEMBLY
DECK ON
(L6)
(L5)
Fig-(C)
BELT LOADING
(L5)
MOTOR ASSEMBLY LOADING
CONNECTOR(2 PIN)
(A)
Fig-(E)
BOTTOM SIDE VIEW
Fig-(A)
Fig-11
11-6. Gear Loading
11. Base Assembly Main (Fig-11)
11-1. Holder Assembly Deck On
11-7. Gear Emergency
1) Push the Locking tabs (L5) at bottom side of the Holder
Assembly Deck On in direction of arrow (A) and
separate to bottom side. (See Fig-(A))
Note: When reassembling, confirm that the Hole (A) of the
Cam Loading is aligned to the Hole (B) of the Gear
Emergency as Fig-(C).
For this alignment, place the Gear Emergency and
Cam Loading as Fig-(D), and then move the Gear
Emergency in direction of arrow (B) until these two
gears are aligned as Fig-(C).
11-2. Frame Assembly Up/Down.
1) Push the two Locking tabs (L6) and lift up the Frame
Assembly Up/Down.
Note: When reassembling, insert the Lever (R1) of the
Frame Assembly Up/Down to the Groove (R2) of the
Gear Emergency and lock the two Locking Tabs
(L6). (See Fig-(B))
11-8. Cam Loading
11-9. Motor Assembly Loading
1) Release two Screws (S7).
2) Unlock the Locking tab (L7) and separate the Motor
Assembly Loading to bottom side.
11-3. Rubber F
11-4. Belt Loading
11-5. Gear Pulley
Note: When reassembling, confirm that the Connector (2
Pin) is aligned as Fig-(E)
1) Release the Screw (S6) and lift up the Gear Pulley.
11-10. Base Main
10
ELECTRICAL MAIN PARTS LIST
REF. NO
PART NO.
KANRI
NO.
DESCRIPTION
REF. NO
IC
SI-RH3-308-00A
SI-KE4-558-00A
SI-TI7-437-40K
SI-AM2-980-01A
SI-AL4-916-14A
IC,BA3308<HR<N>>
IC,KIA4558P<HR<N>>
IC,SN74AHC374PWLE
IC,AM29F800B-120EC<LH<N>>
IC,AT49F1614-90TC<HR<N>>
SI-AL4-981-92B
SI-GS7-142-60E
SI-MQ5-316-25A
SI-HI6-417-03B
SI-AL2-402-10E
IC,AT49F8192A-90TC<LH<N>>
IC,GM71C4260CJ-60
IC,V53C16256HK50
IC,HD6417034AFI20
IC,AT24C02N-10SC-2.7
SI-SS2-402-10A
SI-KE3-930-00G
SI-HY2-580-10A
SI-JR3-414-00C
SI-SH3-130-00A
IC,KS24C021CS
IC,KIA393F-EL
IC,GDC25D801AA
IC,NJM3414AM-TE1,3K/REEL
IC,PQ3DZ13U
SI-CU3-000-00A
SI-FA1-117-25A
SI-SS4-161-02F
SI-GS7-216-16C
SI-BB1-700-00A
IC,ZIVA3-PE0
IC,RC1117ST-2.5
IC,KM4161020CT-G7
ICGM72V161621ET-7
IC,PLL1700E 20P
SI-RH6-859-20A
SI-RH5-983-20A
SI-SA8-661-12C
SI-SS7-542-00A
87-001-196-010
IC,BA6859AFP-E2
IC,BA5983FP-E2
IC,LC866112B-5N21
IC,KA7542Z
IC,KIA7042P
SI-BB1-716-00A
SI-JR4-580-00B
SI-CB5-331-00A
SI-SH2-050-00A
SI-RW8-610-00A
IC,PCM1716E 28P
IC,NJM4580M
IC,CS5331A-KS<HR<N>>
IC,PQ20WZ5U 20WZ51
IC,BT861
SI-SK6-153-00A
SI-SS4-310-00A
SI-KE4-310-00A
SI-SS7-808-00H
IC,STR-G6153T 5P
IC,KA431AZ
IC,KIA431 3P
IC,KA78R08 4P
PART NO.
C216
C218
C219
C220
C224
KANRI
DESCRIPTION
NO.
SC-H71-06C-611
C-CAP,10UF-6.3V
SC-H71-06C-611
C-CAP,10UF-6.3V
SC-H71-06C-611
C-CAP,10UF-6.3V
SC-H81-07C-621
C-CAP,100UF-6.3V
SC-H71-06C-611
C-CAP,10UF-6.3V
C226
C230
C302
C310
C311
SC-H71-06C-611
SC-H71-06C-611
SC-H81-07C-691
SC-H71-06F-621
SC-H71-06F-621
C-CAP,10UF-6.3V
C-CAP,10UF-6.3V
C-CAP,100UF-6.3V
C-CAP,10UF-16V
C-CAP,10UF-16V
C708
C709
C712
C713
C714
SC-H71-06C-611
SC-H82-27D-611
SC-H71-06C-611
SC-H71-06C-611
SC-H71-06F-621
C-CAP,10UF-6.3V
C-CAP,220UF-10V
C-CAP,10UF-6.3V
C-CAP,10UF-6.3V
C-CAP,10UF-16V
C718
CE201
CE202
CE203
CE205
SC-H71-06C-611
SC-H84-76C-611
SC-H84-76C-611
SC-H84-76C-611
SC-H84-76C-611
C-CAP,10UF-6.3V
C-CAP,47UF-6.3V
C-CAP,47UF-6.3V
C-CAP,47UF-6.3V
C-CAP,47UF-6.3V
CE206
CE210
CE211
CE221
CE223
SC-H84-76C-611
SC-H84-76C-611
SC-H84-76C-611
SC-H84-76C-611
SC-H84-76C-611
C-CAP,47UF-6.3V
C-CAP,47UF-6.3V
C-CAP,47UF-6.3V
C-CAP,47UF-6.3V
C-CAP,47UF-6.3V
CE228
CE609
CE610
CE710
CE721
SC-H84-76C-611
SC-H81-07F-611
SC-H81-07F-611
SC-H84-76C-611
SC-H84-76C-611
C-CAP,47UF-6.3V
C-CAP,100UF-16V
C-CAP,100UF-16V
C-CAP,47UF-6.3V
C-CAP,47UF-6.3V<HR<N>>
CE722
CE723
CE724
X101
X301
SC-H84-76C-611
SC-H71-05J-611
SC-H71-05J-611
S2-12H-B20-02A
S2-02R-427-01G
C-CAP,47UF-6.3V<HR<N>>
CAP,1U-35V<HR<N>>
CAP,1U-35V<HR<N>>
CCR20.0MC6T TDK 20000000H
C-RESO 27MHZ 20P
JUNCTION C.B
TRANSISTOR
ST-R38-750-9AC
ST-R10-370-9BB
ST-R10-300-9AE
ST-R10-500-9AB
ST-R10-500-9AD
CHIP KTC3875S-GR-T1
C-TR,2SA1037K-Q
TR,KRC103M
TR,KRC105M
TR,KRA105M
ST-R15-040-9BF
ST-R15-050-9AD
ST-R13-040-9BA
ST-R11-510-0AA
ST-R31-980-9AC
TR,KTA1504S-Y
TR,KTA1505S-Y
TR,KTD1304S
TR,KSB1151-Y
TR,KTC3198-TP-BL
SD-R49-500-9AA
87-020-465-080
SD-D19-300-9AB
SD-D01-000-9CA
87-A40-284-080
DIODE,RB495D
DIODE,1SS133
C-DIODE,KDS193
DIODE,EG01CW
DIODE,ERA22-10
SD-D01-000-9AC
87-017-352-010
SD-R10-451-0AA
SD-R18-020-9AA
SD-R15-402-0BA
DIODE,EU01W
DIODE,RU3YXLF-C1 100V2
DIODE,B10A45V1
DIODE,ERA18-02KFRB
DIODE,1N5402
SD-Z51-000-9HA
ZENER,MTZ5.1B 0.5W
MAIN C.B
SC-H71-06C-611
SC-H71-06C-611
SC-H71-06C-611
SC-H71-06C-611
SC-H71-06C-611
87-010-140-080
87-010-140-080
87-010-140-080
87-010-140-080
SR-D01-01H-633
CAP,E 47-16V
CAP,E 47-16V
CAP,E 47-16V
CAP,E 47-16V
RES,1-1/2W
R452
SR-D01-01H-633
RES,1-1/2W
C500
C501
C502
C506
C507
SC-E22-73D-638
SC-E10-63F-638
SC-E10-63F-638
SC-E47-63J-638
SC-E10-63F-638
CAP,E
CAP,E
CAP,E
CAP,E
CAP,E
C512
C513
DIG501
LED501
RC501
87-010-140-080
87-010-140-080
S3-02H-V00-1D0
SD-L32-531-9AA
S7-12R-083-8GA
CAP,E 47-16V
CAP,E 47-16V
7-BT-259GK DH
LED SPR325MVWT31(GRN)
TSOP1238UQ1 TEMIC 8MM 37 RC
SW501
SW502
SW503
SW503
SW504
S5-562-19B-000
S5-562-19B-000
S5-562-19B-000
S5-562-19B-000
S5-562-19B-000
SW,SKHV10910B
SW,SKHV10910B
SW,SKHV10910B
SW,SKHV10910B
SW,SKHV10910B
SW505
SW506
SW507
SW510
SW511
S5-562-19B-000
S5-562-19B-000
S5-562-19B-000
S5-562-19B-000
S5-562-19B-000
SW,SKHV10910B
SW,SKHV10910B
SW,SKHV10910B
SW,SKHV10910B
SW,SKHV10910B
SW512
SW513
SW514
S5-562-19B-000
S5-562-19B-000
S5-562-19B-000
SW,SKHV10910B
SW,SKHV10910B
SW,SKHV10910B
TIMER C.B
DIODE
C204
C207
C213
C214
C215
CE450
CE451
CE452
CE453
R451
C-CAP,10UF-6.3V
C-CAP,10UF-6.3V
C-CAP,10UF-6.3V
C-CAP,10UF-6.3V
C-CAP,10UF-6.3V
11
220-10V
10-16V<HR<N>>
10-16V
47UF-35V
10-16V
REF. NO
X501
PART NO.
KANRI
DESCRIPTION
NO.
S6-160-20P-000
CSA6.00MGU MURATA 6MHZ
REF. NO
JACK C.B
CV1
CV10
JACK1
JACK2
JACK3
87-010-060-080
SC-E10-86F-630
S6-12R-L00-1A0
S5-720-75A-000
S6-12R-IH0-05G
CAP,E 100-16V
CAP,E 1000-16V
TOTX178 HORIZONTA JK
BJP-202L BAEEN BLACK
PJ6031MG PARK ELEC AU PLATED
JACK4
S6-12R-BH0-08A
YKF51-5506 JALCO HORIZONT4P
KEY C.B
LED501
SW508
SD-L32-531-9AA
S5-562-19B-000
LED SPR325MVWT31(GRN)
SW,SKHV10910B
PART NO.
C934
!F901
!F902
!IC903
!IC903
KANRI
DESCRIPTION
NO.
SC-E47-7CD-638
CAP,E 470UF-10V
S5-850-11T-000
FUSE,1600MA 250V
87-001-196-010
ICP-N10 T104
S6-570-62B-000
SENSOR PC123Y
S2-309-024-040
SENSORLTV-817B PHOTO COU
!L901
!L901
L902
L903
R901
S6-161-45H-000
S6-161-45J-000
S6-330-88G-000
S6-330-88D-000
S6-140-07R-000
FILTER SHT LFS2020V4-04350
FL BUJEON V-04350
COIL,CHOCK TP 5MM
COIL,20UH
RES,2.7-2W
R902
R911
R922
!T901
!V901
SR-S10-03K-619
SR-S05-10K-619
SR-S12-00J-619
S6-420-23T-000
S6-560-04F-000
RES,100K-2W
RES,0.51-2W
RES,M/F 120-1W
PT,SHT-023T/KSE-023T
SVR681D10A SAMYANG 680V
MIC C.B <HR>
POWER C.B
C900
C901
C902
C902
C903
87-010-408-040
S6-240-88B-000
S6-240-88B-000
S6-240-88F-000
S0-2TF-H68-0M0
CAP,E 47UF-50V
CAP,0.1UF-250V
CAP,0.1UF-250V
CAP,PCX2 275V 0.1UF,M
CAP,E 68U-400V
C905
C906
C907
C913
C916
87-016-375-010
S6-240-87B-000
SA-1B3-0KH-2M0
87-012-379-010
87-010-387-010
CAP,0.01UF-630V
CAP,100P-1KV
CAP,220PF-400V
CAP,3300PF-400V
CAP,E 470UF-25V KME
C918
C919
C921
C923
C924
87-010-112-080
87-010-408-040
SC-E22-76F-638
87-010-237-910
87-010-237-910
CAP,E
CAP,E
CAP,E
CAP,E
CAP,E
100-16V
47UF-50V
220UF-16V
1000UF-16V
1000UF-16V
C925
C926
C927
C929
C932
87-010-375-080
87-010-408-040
87-015-684-080
87-010-112-080
SC-E47-7CD-638
CAP,E
CAP,E
CAP,E
CAP,E
CAP,E
330-10V
47UF-50V
47-16V
100-16V
470UF-10V
CM1
CM2
CM3
CM4
CM6
87-015-681-080
SC-E10-76D-638
87-015-681-080
87-015-681-080
SC-E10-76D-638
CAP,E 10-16V<HR<N>>
CAP,100M-10V<HR<N>>
CAP,E 10-16V<HR<N>>
CAP,E 10-16V<HR<N>>
CAP,100M-10V<HR<N>>
CM7
CM8
CM10
CM12
CM13
87-015-681-080
87-010-402-040
87-010-402-040
87-010-402-040
87-010-371-080
CAP,E
CAP,E
CAP,E
CAP,E
CAP,E
CM14
CM23
CM25
CM26
MJ1
87-015-681-080
87-010-371-080
87-015-681-080
87-015-681-080
S6-12R-FV0-01B
CAP,E 10-16V<HR<N>>
CAP,E 470-6.3V<HR<N>>
CAP,E 10-16V<HR<N>>
CAP,E 10-16V<HR<N>>
HTJ-064-255GG KUNMING MIC PJK
<HR<N>>
VR1
VR2
VR3
S1-10R-RHP-03A
S1-10R-RHP-03A
S1-10R-RHP-03A
VR,RK09K1110Z0223B 6.5-2<HR<N>>
VR,RK09K1110Z0223B 6.5-2<HR<N>>
VR,RK09K1110Z0223B 6.5-2<HR<N>>
10-16V<HR<N>>
2.2-50V<HR<N>>
2.2-50V<HR<N>>
2.2-50V<HR<N>>
470-6.3V<HR<N>>
• Regarding connectors, they are not stocked as they are not the initial order items.
The connectors are available after they are supplied from connector manufacturers upon the order is received.
CHIP RESISTOR PART CODE
Chip Resistor Part Coding
8 8
A
Figure
Resistor Code
Value of resistor
Chip resistor
L
W
t
:A
Resistor Code : A
1.0
0.5
0.35
104
1.6
0.8
0.45
108
2
1.25
0.45
118
3.2
1.6
0.55
128
Dimensions (mm)
Wattage
1/16W
Type
1005
Tolerance
5%
Symbol
CJ
1/16W
1/10W
1608
2125
5%
5%
CJ
CJ
1/8W
3216
5%
CJ
Form
L
t
W
12
TRANSISTOR ILLUSTRATION
C2
C
B
ECB
ECB
KRA105M
KRC105M
KRC103M
KSB1151
E
BCE
2SA1037K KTC3875S
KTA1504S KTC4419
KTA1505S KTD1304S
KTC3198
13
KSE13005F
B1
E1
E2
B2
C1
UMX1N
UMZ1N
14
AC 120V
60Hz
OPEN S/W
LIMIT S/W
FL DISPLAY
POWER
BOARD
focus, tracking, sled
KEY INPUT
IC500
LC866112
AGND,GND,UGND
+5VU
+5VD
+5VA
+9V
-21.8V
-27V
-22.5V
Loading
spindle
PICK
UP
CLOSE S/W
M
DECK MECHANISM
M
LOADING
MOTOR
SPINDLE
MOTOR
DVD : A, B, C, D
DVD : RF
CD : A, B, E, F
REMOCON
RECEIVER
RXDO/TXDO/SCKO
POWER CONTROL
SPINDLE_FG
IC401
BA5983
POWER
DRIVER
DRAM
MCK
(33.8688MHz)
REQZI
SDCLKI, ZISENB
DVD_DATA[0:7]
IIC_DATA,
IIC_CLK
DA_DATA,
DA_LRCK,
DA_BCK
IC703
PCM1716
AUDIO
DAC
DA_XCK
DA_DATA,
DA_LRCK,
DA_BCK
IC306
GM72V1621
1M X 16bit
SDRAM
27MHz
X-TAL
IC308
PLL1700
CLOCK
GENERATROR
MPEG RST
DAC_L0,
S_CLK
S_DATA
S_CLK, S_DATA,
DPLL_L
D[00:07]
A[00:02]
SENS, FOK, SLD_FG,
MSDAT0,DEFECT,DSP_SENSE,
SQSO, SQCK, AO[0:5]
XLAT, S_CLK, S_DATA, DO[0:7]
FLASH
MEMORY
IC108
HD6417034
SLD_FG
FDO,TDO,
FMO
MON, SPINDLE_DRV
DRAM
256K x 16bit
IC206
DVDSP-3301
CD/DVD DSP
DVD SERVO
RFZ HOLD
FE, TE, RFRP, SBADD, DVD/CD RF
TEBAL, FEBAL,
DPOCTL, EQF, EQB
LOADING DRIVE
IC400
BA6859FP
SPINDLE
MOTOR
DRIVER
IC201
TA1254F
RF SIGNAL
PROCESSOR
MIRR, TZC
ICADDR[0:8]
Comp.
R
L
IC301
ZiVA-3
MPEG A/V
Decoder
DVD_SD_CS0,
DVD_UDQM
DVD_MD[0:15]
DVD_MA[0:11]
L
AUDIO
OUT
R
AMP
DVD_SD_CAS,
DVD_SD_RAS
DVD_SD_CLK
DVD_MWE
C
Y
Pr
Pb
FILTER
Component
VIDEO OUT
Y
FILTER
Composite, Y, C
IC801
BT861A
NTSC/PAL
Encoder
27MHz
ICDATA[00:15]
DVD_LDQM, DVD_SD_CS1
VDATA[0:7]
IC307
GM72V1621
1M x 16bit
SDRAM
Vsync
RFRP,
TE, Vref
Hsync
Composite
DISC
BLOCK DIAGRAM-1 (OVERALL)
Q901
KTC4419
SWITCHING IC
RECTIFIER
15
AC110-240V
FEED B.
LPF
LPF
RECTIFIER(5.2V)
LPF
RECTIFIER(10V)
RECTIFIER(14V)
RECTIFIER(FLD)
PWR ON/OFF
REG(8V)
U5V
A5V
D5V
8V
12V
-24V
F-
F+
BLOCK DIAGRAM-2 (POWER)
TRANS
LINE FILTER
M/D
PICK
UP
spindle
4
4
16
focus, tracking, loading, sled
IC400
BA6859AFP
Spindle
Motor Driver
CD : A, B, E,F
DVD : RF
DVD : A,B,C,D
IC401
BA5983
Power Driver
IC201
TA1254AF
RF Signal
Processor
FDO, TDO, FMO
loading drive
SPINDLE_FG
SLD_FG
TEBAL, FEBAL,
DPOCTL, EQF, EQB
MON, SPINDLE_DRV
5
DVD/CD RF
FE,TE,RFRP,SBADD 4
RFZ_HOLD
2
IC206
GDC25D801
CD/DVD DSP
MIRR,TZC
IC205
DRAM
256K x 16bit
ICADDR[0:8]
9
IC204
comp.
16
3
ICDATA[00:15]
RFRP,
TE, Vref
MCK (33.8688MHz)
REQZI
SDCLKI, ZISENB
ZO[0:7]
8
2
AO[0:5]
6
XLAT,S_CLK, S_DATA
3
DO[0:7]
SQSO, SQCK
2
8
SENS, FOK, SLD_FG,
MSDATO, DEFECT, DSP_SENSE
5
UCOM
I/F
MPEG
I/F
MPEG
I/F
UCOM
I/F
UCOM
I/F
BLOCK DIAGRAM-3 (RF/DSP/SERVO)
MPEG I/F
(IC301)
µ-com I/F
(IC108)
17
DA_DATA0
DA_XCK
DA_BCK
DA_LRCK
DAC_L0
S_CLK
S_DATA
MPEG_RST
CH 1/2 : DOWNMIX Lt / Rt
IC703
PCM1716
Audio DAC
R0
L0
IC704
LPF &
Buffer
NJM4580M
OP AMP
Rt
Lt
TO
JACK BOARD
BLOCK DIAGRAM-4 (AUDIO)
µ-COM
I/F
DSP
I/F
18
2
8
3
2
8
IC306
GM72V1621
1M x 16bit
SDRAM
4
DVD_SD_CAS
DVD_SD_RAS
DVD_SD_CLK
DVD_MWE
DVD_MA[0:11]
DVD_MD[0:15]
DVD_SD_CS0, DVD_UDOM 2
IIC_DATA, IIC_CLK
MPEG_ERROR
D[00:07]
A[00:02]
REQZ1
SDCLK1,ZISENB
DVD_DATA[0:7]
12
2
DVD_LDOM,
DVD_SD_CSI
IC307
GM72V1621
1M x 16bit
SDRAM
16
IC301
CL61330
MPEG A/V
Decoder
4
8
2
27MHz
X-TAL
IC308
PLL1700
CLOCK
GENERATROR
MPEG_CLK
DA_XCK
VDATA[0:7]
HSYNC, VSYNC
SPDIF
DA_BCK
DA_DATA[0:3]
SERVO
I/F
MCK
VIDEO
I/F(A/V)
UCOM
I/F
Y/C
COMPOSITE1
Pr
Pb
S_CLK, S_DATA, DPLL_L
IC801
BT861A
NTSC/PAL
Encoder
Y
AUDIO
I/F(A/V)
BLOCK DIAGRAM-5 (MPEG)
BLOCK DIAGRAM-7 (MIC) <HR>
2
D[00:15]
16
9
A[01:09]
D[00:15]
2. IF a microphone is connected at this time, MICOM recoguizes the connection and prepares the composition of external voice and
internal melody.
4. This digital signal enters C-CUBE that is MPEG IC and is added to the output of DVD DSP (P-Processor).
5. This mixed signal is output to AV JACK after passing through AUDIO DAC(PCM1716).
FRONT
I/F
5
D[00:04]
8
PWR_CTL,
SENS, LIMIT_SW,
MIC_ON, CLOSE_SW,
OPEN_SW, MPEG_WAIT,
ZISERR
3
A[19:21]
/IOCS1, /WR 2
IC101
XC9536
EXPANDER
SENS_MCOM,
MICOM_WAIT
2
MPEG_ERROR,
DAC_L0,
RF_LAT,
/DSP_CS,
/MPEG_CS,
/PP_CS
6
19
MICOM_RESET
A[01:19]
IC106
FLASH
MEMORY
512K x 16
D[00:15]
16
19
A[00:21] 22
1. The unit turns to KARAOKE MODE with ou-screen lyrics display and melody sound when it play backs VCD or DVD KARAOKE
DISC.
3. The week signal of the microphone is converted to the digital signal after voice output that has passed through PREAMP(BA3308) and
AMP(KIA4558) passes through (CS5331) that is Audio ADC(Analog to Digital convertor).
16
IC108
HD6417034
MAIN µ-COM
2
IIC_CLK,
IIC_DATA
IC114
EEPROM
AT24C02
D[00:07], A[00:02], IIC_CLK, IIC_DATA, SCLK0,
MPEG_INT
MPEG
I/F
ECHO, MIC_A, DISC_A, S_DATA, S_CLK
A/V
I/F
IC107
DRAM
256K x 16
EXP_W2,
/PWR_CLT
D[00:07]
8
D[00:07], A[00:05], E_SIN, E_CLK
LOAD FR, F/R, LOCK, DEFECT, FOK,
DSP_SENSE
BCA_CODE, SPINDLE_FG, SLD_FG,
IC102
74HC374
MPEG_RST,
E_DR,
/ZOOM_RST,
/S_XRST,
XLAT,
ACT_MUTE,
V_MUTE,
A_MUTE
8
DSP
I/F
SERVO
I/F
BLOCK DIAGRAM-6 (SYSTEM CONTROL)
20
WIRING-1 (MAIN: COMPONENT SIDE)
14
13
12
11
10
9
8
6
7
4
5
3
2
1
A
MAIN C.B
(COMPONENT SIDE)
TO/FROM
POWER C.B
CON902
TO/FROM
JUNCTION C.B
CN402
TO/FROM
JUNCTION C.B
CN404
B
2
20
1
2
10
25
1
19
1
26
E
E
C
64
49
48
1
1
2
TO/FROM JACK C.B
CON06
TO/FROM TIMER C.B
CN507
E
R801
33
16
R184
C128
14
17
15
5
1
R191
1
5
5
8
5
1
4
R787
R714
1
53
52
105
84
R726
C715
R723
R721
C713
E
57
85
56
R399
E
R364
R365
R366
112
1
105
F
2
104
TO/FROM JACK C.B
CON07
156
157
29
1
28
1
156
157
208
15
21
Cxxx
1
G
22
40
R384 208
1
R385
1
53
R307
2
22
R729
C712
14
21
R732
CE711
D
1
104
NOTE
R727
C227
2
32
52
R312
R309
H
Lxxx
Rxxx
20
21
I
C
E
B
E
J
21
22
WIRING-2 (MAIN: CONDUCTOR SIDE)
1
2
3
4
5
6
7
9
8
11
10
12
13
A
MAIN C.B
(CONDUCTOR SIDE)
B
20
11
1
10
C
D
25
24
48
1
1
E
44
50
1
50
25
26
25
26
4
1
3
8
5
1
4
40
34
1
1
6
33
11
12
23
22
3 1
4 6
1
F
4
8
8
5
1
4
C728
5
20
11
10
20
1
R188
28
15
1
14
R777
G
21
R717 CE712
R736
E
NOTE
E
Cxxx
5
R193
E
5
E
H
C202
8
1
80
E
E
E
1
E
61
60
1
4
E
Lxxx
8
5
E
20
Rxxx
1
I
21
R823
E
40
C
B
E
4
41
E
J
23
24
E
14