Bissell | 3 3 N 7 | User`s guide | Bissell 3 3 N 7 User`s guide

TM
USER'S GUIDE
10N4 SERIES 220-240V
2
Thank You
3
Safety Instructions
4-5
6
7-12
13-15
Product View
Assembly
Operations
Maintenance and Care
16
Troubleshooting
17
Accessories
18
Replacement Parts
19
Warranty
20
Consumer Care
Thanks for buying a BISSELL Lift-Off™ Deep Cleaner
We’re glad you purchased a BISSELL Lift-Off deep cleaner. Everything we
know about floor care went into the innovative design and construction
of this complete, high-tech home cleaning system.
Your BISSELL Lift-Off deep cleaner is well made, and we back it with a
limited two year warranty. We also stand behind it with a knowledgeable,
dedicated Consumer Care department, so, should you ever have a problem, you’ll receive fast, considerate assistance.
My great-grandfather invented the floor sweeper in 1876. Today, BISSELL
is a global leader in the design, manufacture, and service of high quality
homecare products like your BISSELL Lift-Off deep cleaner.
Thanks again, from all of us at BISSELL.
Mark J. Bissell
Chairman & CEO
2
w w w. b i s s e l l . c o m IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance,
basic precautions should be observed,
including the following:
Read all instructions
before using your
deep cleaner.
Always connect to a properly Earthed
outlet. Unplug from outlet when not in use
and before conducting maintenance or
troubleshooting.
WARNING:
To
reduce the risk of fire,
electric shock, or injury:
■ Use indoors only
■ Do not immerse; use only on surfaces
moistened by cleaning process
■ Do not leave machine when it is plugged in
■ Do not service machine when it is plugged in
■ If the supply cord is damaged, it must
be replaced by the manufacturer or its
service agent in order to avoid a hazard
■ Do not use machine if it has been
dropped, damaged, left outdoors or
dropped into water
■ Do not pull or carry by cord, use cord as a
handle, close door on cord, pull cord around
sharp corners or edges, run appliance over
cord, or expose cord to heated surfaces
■ Do not carry the appliance while in use
■ Do not unplug by pulling on cord; unplug
by grasping plug not the cord
■ Do not handle plug or appliance with
wet hands
■ Do not put any object into appliance openings,
use with blocked opening or restrict air flow
■ Do not expose hair, loose clothing, fingers
or body parts to openings or moving parts
■ Do not pick up hot or burning objects
■ Do not pick up flammable or combustible
materials (lighter fluid, petrol, kerosene,
etc.) or use in the presence of explosive
liquids or vapours
■ Do not use appliance in an enclosed space
filled with vapours given off by oil base
paint, paint thinner, some moth proofing
substances, flammable dust, or other
explosive or toxic vapours
■ Remove plug from electrical outlet before
cleaning or maintaining the appliance
w w w. b i s s e l l . c o m ■ Not intended for use by persons (including
children) with reduced physical, sensory or
mental capabilities, or lack of experience
and knowledge, unless they have been
given supervision or instruction concerning
use of the appliance by a person responsible for their safety
■ Young children should be supervised to ensure
that they do not play with the appliance
■ Do not pick up toxic material (chlorine
bleach, ammonia, drain cleaner, petrol, etc.)
■ Do not modify the Earthed plug
■ Do not use for any purpose other than
described in this User’s Guide
■ Use only manufacturer’s recommended
attachments
■ Use only cleaning products formulated
by BISSELL for use in this appliance to
prevent internal component damage
■ Keep openings free of dust, lint, hair, etc.
■ Keep appliance on a level surface
■ Turn off all controls before unplugging
■ Be extra careful when cleaning stairs
■ Pay close attention when working
around children
SAVE THESE
INSTRUCTIONS
FOR FUTURE USE
This model is for household use only.
This appliance
WARNING:
must be Earthed.
IMPORTANT
FOR OPERATION ON A 220-240 VOLT
A.C. 50/60 Hz POWER SUPPLY ONLY.
If your appliance is fitted with a
nonrewireable BS 1363 plug it must not be
used unless a 13 amp (ASTA approved to BS
1362) fuse is fitted in the carrier contained
in the plug. (Spares may be obtained from
your BISSELL supplier). If for any reason the
plug is cut off, it must be disposed of, as it is
an electric shock hazard should it be inserted
into a 13 amp socket.
3
Product view
Upper Handle
Carry Handle
Heat
Indicator Light
Formula &
Water Tank
Power Button
Power Cord
Quick Release™
Cord Wrap
Flex Hose
Dirty Tank
Portable Spot
Cleaning Release
Pedal
EdgeSweep™
Brushes
4
w w w. b i s s e l l . c o m Removeable
Nozzle Assembly
Product view
Spray Trigger
Cord Clip
Tool Storage
Support Handle
Tool Storage
(select models)
WARNING:
To reduce the risk of fire
Hose Secure
Latch
Recline Pedal
Cleaning formula
and electric shock due
to internal component
damage, use only
BISSELL cleaning formulas
intended for use with the
deep cleaner.
Keep plenty of genuine BISSELL 2X cleaning formula on hand so you can clean and protect
whenever it fits your schedule. Always use genuine BISSELL deep cleaning formulas.
Non-BISSELL cleaning formulas may harm the machine and will void the warranty.
709 mL BISSELL
2X Fibre
Cleansing
Advanced
Formula with
Scotchgard™
protector
#62E5-E
709 mL BISSELL
2X Multi-Allergen
Advanced
Formula with
Scotchgard™
protector
#89Q5-E
w w w. b i s s e l l . c o m 709 mL BISSELL
2X Pet Stain &
Odor Advanced
Formula with
Scotchgard™
protector
#99K5-E
709 mL BISSELL
2X Natural
Orange
Advanced
Formula with
Scotchgard™
protector
#83P3-E
709 mL BISSELL
2X Lavendar
Essence
Advanced
Formula with
Scotchgard™
protector
651 mL
Tough Stain
Precleaner
#0400-E
#34B5-E
5
Assembly
Your Lift-Off deep cleaner comes in
two easy to assemble components:
1. Upper handle
2. Portable spot cleaner/Base
The only tool you will need to
assemble your cleaner is a long
Phillips screwdriver.
1. Slide the upper handle onto the body
of the machine by guiding the 2 posts
on the body into the opening on the
upper handle.
1.
2.
IMPORTANT
IMPORTANT
ASSEMBLY
ASSEMBLYINSTRUCTIO
INSTRUCTIO
Use Use
a minimum
a minimum
of a of
#2ax#2
4"xor4"#2orx#2
100mm
x 100mm
Philips
Philips
screwdriver
screwdriver
for assembl
for asse
1.
2.
IMPORTANT
2. Firmly holding the upper handle in
INSTRUCTIONS
place, screw 2ASSEMBLY
screws into the marked
a minimum of a #2 x 4" or #2 x 100mm Philips screwdriver
for
Slide
Slide
theassembly.
the
upper
upper
handle
handle
ontoonto Firmly
Firmly
holding
holding
thethe
upper
upper At an
At upward
an upwa
holes at an upwardUse angle
above the
the the
body
body
of the
of the
machine
machine
by by4.
handle
handle
in place,
in place,
screw
screw
2 2 the the
remaining
remain
3.
support handle.
guiding
guiding
the the
2 posts
2 posts
on the
on the screws
screws
intointo
thethe
marked
marked the the
marked
marked
ou
body
body
into
into
the
the
opening
opening
on
on
holes
holes
at
an
at
upward
an
upward
angle
angle
under
under
the
the
sup
3. At an upward angle, screw the remaining
Cord
the the
upper
upper
handle.
handle.
above
above
the the
support
support
handle.
handle. Hose
2 screws into the marked outermost holes
side
side
under the support handle.
4. Wrap power cord around Quick
Release Cord Wrap.
Slide the upper handle onto
Firmly holding the upper
At an upward angle, screw
body of the machine by handle in place, screw 2
the remaining 2 screws into
5. Wrap flex the
hose
around the hose wrap
guiding the 2 posts on the screws into the marked
the marked outermost holes
5.
and securebody
with
secure
latch.
into hose
the opening
on
holes
at an upward angle
under the support handle.
the upper handle.
above the support handle.
6. Align the product as image 4 shows
and firmly push down the portable spot
cleaner until it is secured on both sides.
7. Check latches on both sides to confirm
it is secured (5).
8. Snap attachment(s) into the back of unit.
NOTE: Portable spot cleaner must
be fully secure to operate in the
upright mode.
6
To further check if the portable
spot cleaner is secure, plug in
and turn on to verify that the
heat indicator light is illuminated.
If the heat indicator light does
not illuminate, release the pod
and re-secure by pushing firmly
until both sides snap into place.
w w w. b i s s e l l . c o m Warning:
Do not plug in your
cleaner until you have
completely assembled it
per the above instructions
and are familiar with
all instructions and
operating procedures.
Operations
Special features
Innovative cleaning technology
This innovative deep cleaner offers two
machines in one. The upright deep cleaner
uses the power of heat, brushes and
cleaning formula to get deep down dirt
for a maximum clean. The portable spot
cleaner detaches to clean tough spots and
stains and hard to reach areas.
Hot water heater
This deep cleaner features a patented
built-in hot water heater which will heat
the hand hot tap water you put in to safely
optimize cleaning effectiveness. The heater
temperature is limited to prevent carpet
damage. The heater automatically turns
on when you turn the machine on. This
operates only in upright cleaning mode.
Scotchgard™ Protector
Carpet protection applied at the mill
typically wears down over time from
heavy foot traffic and everyday cleaning,
including deep cleaning. To help restore
this important protection, only BISSELL
offers deep cleaning formulas with
Scotchgard protector. This offers extra
protection against dirt and tough stains
to keep your carpets looking good longer.
Pedal Graphic
Tip:
For easy carrying, grab the
carry handle portable spot
cleaner and balance with
the handle on the back of
the machine.
Microban® antibacterial
product protection
Microban antibacterial product protection
is built into key components to help prevent
the growth of harmful common household
bacteria. It helps to keep the unit fresher
and cleaner between uses.
w w w. b i s s e l l . c o m 7
Operations
Warning:
Before you clean
1. Move furniture to another area if cleaning
an entire room (optional).
2. Vacuum area with a dry vacuum cleaner
thoroughly before deep cleaning.
3. Pretreating (optional):
3a.Pretreating is recommended to improve
cleaning effectiveness for heavily soiled
carpet in high traffic areas such as
entryway and hallways.
3b.BISSELL Tough Stain precleaner
Spray the BISSELL Tough Stain
precleaner formula onto heavy traffic
areas, soiled areas or stains.
Allow to penetrate for at least 3 minutes.
Clean as normal, using the deep
cleaner in upright mode, following the
instructions below.
Upright cleaning mode
Filling formula & water tank
1. Remove tank from the base of the machine
by lifting up tank carry handle.
Note: This tank was designed with a
flat bottom so it can be easily filled.
2. Unscrew the black cap and remove
bottle insert.
3. Fill tank with hand hot tap water to the
water fill line. Add 60 mL of BISSELL 2X
formula to the tank.
4. Replace the bottle insert in the tank and
tighten the black cap. Replace the tank
on the deep cleaner.
Cleaning
1. Plug into a proper outlet and press the
power button. Allow 1 minute for the hot
water heater to warm-up before cleaning.
2. While pressing the spray trigger, make one
slow forward wet pass and another one back.
8
w w w. b i s s e l l . c o m To reduce the risk of fire, use only
BISSELL deep cleaning formula
for full size machines in your
deep cleaner. Use of cleaning formulas that contain lemon or pine
oil may damage this appliance
and void the warranty. Chemical
spot cleaners or solvent-based
soil removers should not be used.
These products may react with the
plastic materials used in your deep
cleaner causing cracking or pitting.
3b.
ATTENTION:
Some Berber carpets have a
tendency to fuzz with wear.
Repeated strokes in the same
area with an ordinary vacuum
or deep cleaner may aggravate
this condition.
1.
2.
Operations
Upright cleaning mode continued
Cleaning continued
CAUTION:
Do not overwet. Take care not to
3. Release the spray trigger and make one
slow forward and backward pass over the
same area. Repeated passes will help aid
in dry time.
4. Continue passes until cleaning area
is complete.
Note: Your machine may be equipped
with a circuit breaker that will automatically shut off the brush if a large
or loose object is caught in the brush
roll. If that happens, be sure to unplug
your machine, remove the foreign
object, and then plug the machine
back in to reset the circuit breaker.
Empty dirty tank
1. When the dirty tank reaches the “FULL”
line on the tank it is time to empty.
2. Remove dirty tank and carry to a utility
sink, toilet or outside (where you will
dispose of the dirty water).
3. To unlock the dirty tank lid, rotate handle
over the back of the tank. Remove lid
and pour out dirty water. Rinse out dirty
tank to remove any debris.
run over loose objects or edges
of area rugs. Stalling brush may
result in premature belt failure.
Tip:
Make only one trip to the
sink by removing the entire
portable cleaner. Fill and
empty in the same trip.
3.
2.
5.
4.
4. Replace top of tank, and rotate the handle
forward to lock in place on front of tank.
5. Before replacing tank on machine, wipe
debris from red filter
Cleaning your machine
1. Flush out machine of any remaining
residual solution.
Fill the formula & water tank with hand
hot tap water and turn on your machine.
Recline handle and press the spray
trigger for about 15 seconds while
making forward and backward passes
on carpet. Continue without pressing
the spray trigger until there is no more
water being suctioned up.
Turn off the machine and wrap the power
cord. Make sure the dirty tank and the
formula & water tank are emptied, rinsed,
and dried before the next use.
Before you replace tank, clean all
debris from red filter screen.
w w w. b i s s e l l . c o m WARNING:
To reduce the risk of fire, electric
shock, or injury, turn power
OFF and disconnect plug from
electrical outlet before performing
maintenance or troubleshooting.
Tip:
For best results empty,
rinse and dry both tanks
before storing.
9
Operations
Upright cleaning mode continued
Cleaning your machine continued
2. Rinse nozzle assembly of any dirt
and debris.
Remove portable spot cleaner from
the base of the machine.
Remove the nozzle assembly from the
machine by unscrewing 3 screws and
lifting away the upper and lower nozzle.
Rinse upper and lower nozzles out
at the faucet.
Place lower nozzle back onto the
machine by hooking the tabs into the
holes on the bottom sides of the front
of the machine.
WARNING:
To reduce the risk of fire,
electric shock or injury unplug
from outlet before servicing.
2.
Place upper nozzle onto the lower
nozzle by hooking the tabs into the
holes on the front of the lower nozzle.
Secure with 3 screws.
3. The inside of the end caps can be
wiped out with a clean paper towel,
or for a more thorough clean, the end
caps can be taken off and rinsed clean.
4. Any loose hair or debris can be pulled
from the brush rolls and thrown away. For
a more thorough clean, follow directions
on page 15 for removal of brush rolls.
Your machine is now ready to be stored.
Note: Store cleaner in a protected,
dry area. Since this product uses
water, it must not be stored where
there is a danger of freezing.
Freezing will damage internal
components and void the warranty.
10
w w w. b i s s e l l . c o m Tip:
Let all parts dry completely
and replace onto machine.
Operations
Portable spot cleaning mode
Preparing the machine
1. Step on the portable spot cleaning pedal
to release the portable spot cleaner.
2. Release flex hose by twisting the hose
secure latch clockwise. Unwrap flex
hose completely.
3. Attach the desired tool to the hose grip
until it snaps together. Make certain the
tool is securely attached.
4. Twist the Quick Release cord wrap clockwise to unwrap the power cord completely and plug into grounded outlet.
Filling tank
1. Follow the instructions for filling the tank
in the upright cleaning mode section on
page 8
Cleaning with Tools:
1. Hold the tool approximately 2.5 cm
above the soiled surface. Press the
spray trigger to apply the cleaning
solution to the soiled area.
Note: Hold end of hose below the
tank water level to help prime the
portable spot cleaner.
2. Using the brush on the tool, gently scrub
the area to be cleaned.
3. Apply downward pressure on the tool
and pull it toward you. The suction
will remove the dirt and cleaning
solution. Continue until no more dirt
can be removed.
w w w. b i s s e l l . c o m bvh
g kvh
gh j j h
d b lg
fd hn l kl
sd jkn f h
Ad bj jh
b j
cv hh
gcg
Important! If using to clean
upholstery, check upholstery tags.
Check manufacturer’s tag before
cleaning. “W” or “WS” on the tag
means you can use your Lift-Off
deep cleaner. If the tag is coded
with an “X” or an “S”(with
a diagonal stripe through it), or
says “Dry Clean Only”, do not
proceed with any deep cleaning
machine. Do not use on velvet or
silk. If manufacturer’s tag is
missing or not coded, check with
your furniture dealer.”)
Manufacturer’s tag
IMPORTANT
Check for colourfastness in
an inconspicuous place. If
possible, check upholstery
stuffing. Coloured stuffing
may bleed through fabric
11
Operations
Portable spot cleaning mode continued
Cleaning with Deep Reach™ Tool
(select models only)
1.
1. Set tool on soiled surfaces and press
the spray trigger to spray solution onto
the soiled area to be cleaned.
2. Slowly move the tool back and forth
over the soiled surface, keeping the
tool in contact with the carpet.
Release spray trigger and move tool
slowly over the soiled area to suction
up water and dirt.
4. Continue to clean the area, working
in small sections, until no more dirt can
be removed.
3.
Empty dirty tank
Follow the instructions under Empty
dirty tank section on page 9 of the
Upright cleaning mode section.
Replacing portable machine on base
1. Align the product as the graphic shows,
with the cord side on the left and hose
side on the right.
2. Push down the portable spot cleaner
until you hear it click securely into
place. Test the fit by pulling up on the
carry handle to make sure it is secure.
Cleaning portable machine
1. Remove and rinse the tools in clean,
running water. Dry and replace in the
tool storage provided.
2. It is recommended that you suction clean
water from a bowl to rinse out the hose.
Then lift end of hose and stretch out to
ensure all water is cleared from hose.
3. Coil flex hose around the hose wrap
and secure with latch.
4. Check suction gate and if it appears
dirty, follow steps 1-4 under Cleaning
Suction Gate on page 13.
12
w w w. b i s s e l l . c o m 1.
Graphic
Maintenance and care
Machine care (check regularly)
WARNING:
To reduce the risk of fire,
Cleaning suction gate
The suction gate automatically diverts
air when the portable deep cleaner is
detached. This should be checked and
cleaned regularly for any dirt
and debris.
electric shock, or injury, turn
power OFF and disconnect
plug from electrical outlet
before performing maintenance
or troubleshooting.
1. Step on the pedal and remove the
portable spot cleaner. Remove dirty
tank.
2.
2. Remove two screws and pull off
suction gate door.
3. Wipe suction gate clean and rinse
suction gate door.
4. Replace suction gate door and
two screws.
Suction
Gate
Cleaning spray tips
1. Step on the pedal and remove the
portable spot cleaner. To remove,
push in tab and pull it out.
Spray
Tips
2. Clean by rinsing under water.
3. Replace by snapping back in.
1.
4. Repeat steps on second spray tip.
Cleaning solution filter
1. Step on the pedal and remove the
portable spot cleaner. Remove the
red solution filter cap on the base
of the machine by inserting a coin
or a flat head screw driver into the
slot on the top.
2. Turn counter clockwise to unscrew.
Set aside.
3. Remove the white filter by the post.
Rinse the filter under water.
4. Replace the white filter back into
the filter area.
2.
Solution
Filter Cap
3.
Note: Make sure the white filter
is seated properly before replacing the red solution filter cap.
5. Replace the red solution filter cap and
turn clockwise to tighten.
5.
Filter
w w w. b i s s e l l . c o m 13
Maintenance and care
Small belt removal and replacement (as needed)
Occasional replacement of one or
both belts may become necessary.
If that is needed, please follow the
instructions below.
1. Turn off the machine, and unplug it from
the outlet. Remove portable spot cleaner.
2. Remove the nozzle assembly from the
machine. Refer to step 2 on page 10.
WARNING:
To reduce the risk of fire,
electric shock or injury,
unplug from the outlet
before servicing.
2.
3. Turn the machine on its side.
IMPORTANT: with portable spot
cleaning pedal facing down.
4. Remove end cap by unscrewing the
3 screws. Take care not to drop the
screws into the unit.
4.
5.
5. Remove 1 silver screw from the
pivot arm.
6. Remove pivot arm by gently lifting up.
7. Remove small brush belt.
8. Replace small brush belt, and reverse
steps above.
9. Manually rotate brushes by hand to
make sure they move freely. May notice
a slight resistance from the motor.
6.
7.
14
w w w. b i s s e l l . c o m 8.
Maintenance and care
Brush removal and large belt replacement (as needed)
Brushes can be removed for cleaning
or replacement as needed.
1. Follow small belt removal Instructions on
page 14 items 1-7.
2. Remove brush rolls by pulling them off
of the metal rods. Be careful not to
lose the small washer at each
end of the brush rolls.
WARNING:
To reduce the risk of fire,
electric shock or injury,
unplug from the outlet
before servicing.
2.
3.
4.
5.
6.
7.
3. Re-attach the large belt to the grooves
on the end of the new brush rolls.
If the belt is damaged, replace with
a new belt.
4. Place cleaned or new brush rolls back
onto the rods. Make sure one washer is
on each end of the rollers prior to sliding
onto the rod. Be sure the brush is seated
completely on the rod.
5. Replace small belt over grooves in
back roller and metal cog.
6. Replace pivot arm and secure with
silver screw.
7. Re-attach end cap by tightening with
the (3) black screws.
8. Replace the nozzle assembly back
onto the machine. Refer to step 2
on page 10.
If you have any questions or are
having trouble installing or replacing
your belt(s) or brushes, please call
BISSELL Consumer Services.
w w w. b i s s e l l . c o m 15
Troubleshooting
Built-in heater ready light does not illuminate
Possible causes
1. The power is not turned ON Remedies
1. The power must be ON to activate the heater ready light
2. The portable spot cleaner is not attached completely
2. Make sure the portable spot cleaner is attached
Push down firmly to check
Reduced Spray or No Spray
Possible causes
Remedies
1. Formula & water tank may be empty
1. Refill tank
2. Formula & water tank may not be seated completely
2. Turn power OFF. Remove and reseat tank
3. Pump may have lost prime in portable spot cleaning mode
3. Hold end of hose below water level in tank to prime
4. The portable spot cleaner is not attached completely
4. Push down firmly to check connection
5. Solution filter may be clogged
5. Follow steps under cleaning filter on page 13
DirtLifter™ PowerBrush does not turn
Possible causes
Remedies
1. The portable spot cleaner is not attached completely
1. Make sure the portable spot cleaner is attached.
Push down firmly to check
2. The unit is in the upright position
2. Brushes only rotate when unit is reclined using the
recline pedal
3. Circuit breaker on machine (if equipped) may have tripped
3. Turn the machine OFF and unplug from outlet. Check
to see if foreign object is caught in brush roll. Remove
object. Plug machine in to reset circuit breaker
4. The belt is off or broken
4. Turn power OFF and unplug unit from outlet. Follow
instructions on pages 14 and 15
Loss of suction power
Possible causes
Remedies
1. Tanks may not be seated properly
1. Pick up both tanks and reseat them so it they fit snugly on
the unit
2. Nozzles may not be assembled properly
2. Unplug the unit. Check to make sure the "lip" of the nozzle is securely hooked into the groove on bottom of the machine (see page 10)
3. The portable spot cleaner is not attached completely
3. Make sure the portable spot cleaner is attached.
Push down firmly to check
4. Dirty tank has picked up maximum amount of
4. Empty dirty tank
dirty water and has reached full line
5. Formula & water tank is empty
5. Check fluid levels in formula & water tank
6. Suction gate is open
6. Check to make sure the suction gate is closed. Follow “Cleaning suction gate” instructions on page 13
Other maintenance or service not included in the manual should be
performed by an authorized service representative.
Thank you for selecting a BISSELL product.
Please do not return this product to the store.
16
w w w. b i s s e l l . c o m Accessories
Item Part No. Part Name
1
2
3
4
5
6
7
203-6651
203-6652
203-6653
203-6654
203-7885
203-7569
310-3040
3” Tough Stain Tool
Powered TurboBrush™ Hand Tool
4” Upholstery Tool
6” Stair Tool
Spraying Crevice Tool
Deep Reach™ Tool
Mesh Bag
*Not all parts are included with every model.
1
2
3
5
6
7
4
Cleaning Formula: Refer to bottom of page 5 of this guide for a full selection
of cleaning formula available for purchase.
w w w. b i s s e l l . c o m 17
Replacement parts
Below please find a list of common replacement parts. While not all of these
parts may have come with your specific machine, all are available to you for
purchase, if desired.
Item Part No. Part Name
1
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
203-7893
203-6675
203-7894
203-7904
203-7896
203-7897
203-7898
203-7901
203-7906
203-7907
203-8105
203-8106
203-7900
203-7899
203-6689
203-7918
203-7917
Formula & Water Tank Assembly (includes cap and insert)
Cap and Insert for Formula & Water Tank
Dirty Tank Assembly (includes entire tank)
Cord Wrap
End Caps with Edge Brushes (2 pack, includes screws)
Spray Tips Assembly (includes two spray tips)
In-line Filter Assembly (includes cap and filter)
Nozzle Gasket
Nozzle Assembly (includes gasket, upper and lower nozzle)
Upper and Lower Nozzle
Brush Assembly (includes 2 brush rolls, 2 axles, and 2 swivel arms)
Brush Single Pack (includes 1 brush roll, and 1 axle)
Small Brush Belt
Large Brush Belt
Hose Secure Latch
Dirty Tank Gasket Assembly (include both gaskets)
Diverter Cover Assembly (includes cover and screws)
*Not all parts are included with every model.
1
2
3
4
7
8
9
10
13
14
15
16
18
w w w. b i s s e l l . c o m 5
11
17
6
12
Warranty
This warranty gives you specific legal rights, and you may also have other rights which may vary from country to country. If
you need additional instruction regarding this warranty or have questions regarding what it may cover, please contact BISSELL
Consumer Care by E-mail, telephone, regular mail as described below, or contact your local in country distributor.
Limited Two Year Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, BISSELL will repair or replace (with new or
remanufactured components or products), at BISSELL’s option, free of charge from the date of purchase by the original
purchaser, for two years any defective or malfunctioning part due to manufacturer defect.
This warranty applies to product used for personal, and not commercial or rental service. This warranty does not apply
to fans or routine maintenance components such as filters. Damage or malfunction caused by negligence, abuse,
neglect, unauthorized repair, or any other use not in accordance with the User's Guide is not covered.
BISSELL recommends that the original packaging be kept for the duration of the warranty period in case such need
arises within the warranty period that the item need re-packing and transportation.
For Australian inquiries:
Monday – Friday 9 am - 5 pm
BISSELL Australia PTY LIMITED
42 Roco Drive
Scoresby 3179
Victoria
Australia
Telephone: 1-800-811-183
For South African inquiries:
Monday – Friday 9 am - 5 pm
Tevo (Pty) Ltd.
PO Box 25234
Gateway 4321
South Africa
Telephone: +27 (0) 86-177-8888
Email: servicecentre@tevo.co.za
For New Zealand inquiries:
Monday – Friday
9 am - 5 pm
Parex Industries LTD.
5 Tolich Place
Henderson 0610
Auckland
New Zealand
Telephone: 0800-247-735
For Middle East & Africa inquiries:
Sunday – Thursday 9 am - 6 pm
BISSELL Middle East & Africa
P.O. Box 61286
Office 017, Technopark Building
Jebel Ali Free Zone
Dubai
United Arab Emirates
Telephone: 971-4-881-8597
For all other inquiries:
Monday – Friday
8 am - 4 pm
BISSELL Homecare, Inc.
PO Box 1888
Grand Rapids, Michigan 49501 USA
Telephone: 01-616-453-4451
Fax: 01-616-453-1383
*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY
BISSELL and its in-country distributors are NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT
EXCEED THE PURCHASE PRICE OF THE PRODUCT.
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR WRITTEN. ANY
IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW, INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE TWO YEAR DURATION
FROM THE DATE OF PURCHASE AS described above.
FOR AUSTRALIAN CONSUMERS ONLY: Our goods come with guarantees that cannot be
excluded under the Australian Consumer Law. You are entitled to a replacement or refund
for a major failure and for compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or replaced if the goods fail to be
of acceptable quality and the failure does not amount to a major failure.
THIS WARRANTY IS IN ADDITION TO OTHER RIGHTS OR REMEDIES UNDER LAW. NOTHING IN THIS
WARRANTY EXCLUDES, LIMITS OR MODIFIES ANY LIABILITY OF BISSELL WHICH IS IMPOSED BY LAW, OR LIMITS
OR MODIFIES ANY REMEDY AVAILABLE TO THE CONSUMER WHICH IS GRANTED BY LAW.
TO MAKE A CLAIM UNDER THIS WARRANTY CONTACT BISSELL AUSTRALIA PTY LTD (DETAILS ABOVE). CONTACT
BISSELL PRIOR TO RETURNING ANY GOODS. WHERE AGREED, BISSELL WILL REIMBURSE REASONABLE
POSTAGE / HANDLING COSTS (IF ANY) FOR RETURNING GOODS TO BISSELL.
w w w. b i s s e l l . c o m 19
Consumer care
If your BISSELL product should require service:
Call BISSELL Consumer Care at the numbers below and we will give you the location of
a BISSELL Authorized Service Center in your area. If you have questions about your warranty
or need replacement parts please contact the numbers below.
For Australian inquiries:
Monday – Friday 9 am - 5 pm
BISSELL Australia PTY LIMITED
42 Roco Drive
Scoresby 3179
Victoria
Australia
Telephone: 1-800-811-183
For South African inquiries:
Monday – Friday 9 am - 5 pm
Tevo (Pty) Ltd.
PO Box 25234
Gateway 4321
South Africa
Telephone: +27 (0) 86-177-8888
Email: servicecentre@tevo.co.za
For New Zealand inquiries:
Monday – Friday
9 am - 5 pm
Parex Industries LTD.
5 Tolich Place
Henderson 0610
Auckland
New Zealand
Telephone: 0800-247-735
For Middle East & Africa
inquiries:
Sunday – Thursday 9 am - 6 pm
BISSELL Middle East & Africa
P.O. Box 61286
Office 017, Technopark Building
Jebel Ali Free Zone
Dubai
United Arab Emirates
Telephone: 971-4-881-8597
For all other inquiries:
Monday – Friday
8 am - 4 pm
BISSELL Homecare, Inc.
PO Box 1888
Grand Rapids, Michigan 49501 USA
Telephone: 01-616-453-4451
Fax: 01-616-453-1383
Or visit the BISSELL website - www.bissell.com
When contacting BISSELL, have model number of cleaner available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________
NOTE: Please keep your original sales receipt.
It provides proof of purchase date in the event
of a warranty claim. See Warranty on page 19
for details.
Do not throw the appliance away with the normal
household waste at the end of its life, but hand it in
at an official collection point for recycling. By doing
this you will help to preserve the environment.
20
w w w. b i s s e l l . c o m ©2012 BISSELL Homecare, Inc
All rights reserved. Printed in China
Part Number 120-4464
Rev 2/12
Visit our website at:
www.bissell.com
Scotchgard is a trademark of 3M
Microban® is a registered trademark
of Microban Products Company
Download PDF