Viking Dishwasher Installation guide

Viking Installation Guide
Viking Range Corporation
111 Front Street
Greenwood, Mississippi 38930 USA
(662) 455-1200
For product information,
call 1-888-VIKING1 (845-4641)
or visit the Viking Web site at
vikingrange.com
F20408B
Professional & Designer 450 Series
Built-In Dishwashers
(092308J)
IMPORTANT–Please Read and Follow!
Table of Contents
Warnings & Important Information ______________________________________ 3
Dimensions & Cutout Dimensions ______________________________________ 4
Specifications ________________________________________________________ 5
Custom Door Panel Specifications ______________________________________ 6
Custom Door Panel Installation Option _________________________________ 7
General Information __________________________________________________ 8
Site Preparation ___________________________________________________ 8
Water Supply _____________________________________________________ 8
Drain_____________________________________________________________ 8
Electrical Connections _____________________________________________ 9
Hardwire Conduit Option _____________________________________________ 10
Trim Installation Options _____________________________________________ 11
Counter Balance Spring Adjustment ___________________________________ 14
Installation Procedure_________________________________________________ 15
Performance Checklist _______________________________________________ 18
Testing for Leaks _________________________________________________ 18
Final Preparation _________________________________________________ 18
Service & Registration ________________________________________________ 18
• Before beginning–please read these
instructions completely and carefully.
• Please ensure that this product is properly
grounded.
• Do not remove permanently affixed labels,
warnings, or rating plates from the
dishwasher. This may void warranty or
create an unsafe product.
• The installer should leave these instructions
with the consumer who should retain for
local inspector’s use and for future
reference.
WARNING
• Please observe all national and local codes.
Plumbing connections must comply with
applicable sanitary, safety and plumbing
codes.
WARNING
Make sure that incoming voltage is the
same as unit rating. An electric rating
plate specifying voltage, hertz, and
amps is attached to the product. Wiring
the dishwasher with more voltage than
it is rated for may cause severe damage.
To reduce the risk of fire, electric shock,
or injury to persons, installation work
and electrical wiring must be done by
qualified technician in accordance with
all applicable codes and standards,
including fire-rated conditions.
WARNING
The dishwasher door may not stay open
by itself until the door panel is installed.
Be aware of this when fastening the
dishwasher to the cabinet.
CAUTION
The dishwasher has a factory installed
backflow preventer. Do Not add an
additional check valve.
WARNING
Electrical power must be turned off at
circuit breaker or fuse box before making
electrical connections. Disconnect the
electrical power supply and place a tag at
the disconnect switch indicating that you
are working on the circuit.
Site Preparation
2
CAUTION
Failure to provide (20” [50.8 cm] above
floor level) a 20” (50.8 cm) high loop may
result in improper operation of the
dishwasher.
It is recommended that a thorough site inspection be
conducted PRIOR to unpacking and moving this appliance.
3
Specifications
Dimensions & Cutout Dimensions
Professional Series
26-3/8”
(67.0 cm)
23-1/8”
(59.0 cm)
26-3/8”
(67.0 cm)
23-3/4”
(60.3 cm)
2
3-7/
(60.6 c8”
m)
Built-In Dishwasher
Description
Overall width
Overall height from floor
2-5/8”
(6.7 cm)
3-3/16”
(8.1 cm)
Overall depth from rear–Professional
Overall depth from rear–Designer
33-7/
(86. 8”
Cutout width
Cutout height
0 cm)
Cutout depth
Electrical requirements
Cabinet Flush
Panel Flush
Water-heating element rating
Inlet water temperature
Designer Series
”
1/4
20- cm)
(51
.4
25-15/16”
(65.9 cm)
23-1/8”
(59.0 cm)
26”
(66.0 cm)
23-3/4”
(60.3 cm)
49”cm)
Inlet water pressure operating range
Inlet water hose
4.5
(12
2-1/4”
(5.7 cm)
2-7/8”
(7.3 cm)
Drain hose
450 Model
23-7/8” (60.6 cm)
33-7/8” (86.0 cm) min.
35” (89.0 cm) max.
To edge of side - 24” (61.0 cm) - includes door panel
With door open - 49” (124.5 cm)
To edge of side - 24” (61.0 cm) - includes door panel
With door open - 49” (124.5 cm)
24” (61.0 cm)
34” (86.4 cm) min.
35” (89.0 cm) max.
24” (61.0 cm)
15.0 amps, 120VAC/60 Hz;
5’ (1.8 m) electrical cord 3 prong plug supplied with unit
1400 watts
120˚F (49˚C) recommended;
Dishwasher will perform properly with cold water
Note: Cycle times will vary
10 to 125 psi (.69 to 8.62 bar)
5’ (1.5 m) braided stainless steel water line with 3/8” (0.95 cm) compression
fitting connected to dishwasher
7’ (2.13 m) 1/2” (1.3 cm) ID “crimp-proof” flexible drain hose
attached to dishwasher, connections provided for 5/8” (1.6 cm),
3/4” (1.9 cm) or 1” (2.5 cm), cut as required
Drain hose high loop required
Height from floor - 20” (51.0 cm) min.
Approximate shipping weight
24”
(61.0 cm)
157 lbs. (70.7 kg)
24”
(61.0 cm
)
Cabinet Flush
Panel Flush
Custom Panel
34” m
in
(86.4 c .
m)
35” ma
(89.0 c x.
m)
23-3/4”
(60.3 cm)
23-1/8”
(59.0 cm)
Cabinet Flush
Panel Flush
Note: A 2”
(5.1 cm) cut-out is
required for
water supply and
discharge lines.
4
5
Custom Door Panel
(Specifications)
(Installation Option)
11-17/32"
(29.3 cm)
5-7/8"
(14.9 cm)
5/8"
(1.6 cm)
5/8"
(1.6 cm)
5/8"
(1.6 cm)
Have the overlay panel constructed per
dimensions. The panel thickness MAY NOT
exceed 5/8” (1.6 cm) for flush installation in most
cabinets. Ensure that the design, construction,
and installation of the panel overlay and its
handle mounting is sufficient to reliably operate
in this application with a maximum panel weight
of 18 lbs. (8.2 kg.) Custom panels should not
exceed 18 lbs. (8.2 kg.)
Obtain four screws with the proper thread type
for the overlay material chosen. The screws
MUST BE #8 flat head, 1-3/4” long and MUST
BE stainless steel to avoid corrosion.
Use 1/4"
router bit
9-1/8"
(23.2 cm)
a
ø1/8" 4 places
(.3 cm)
To remove face panel of dishwasher remove only the
4 Phillips screws - do not remove any other fasteners.
b
If dishwasher has a metal door skin installed,
remove the four screws. DO NOT remove any
other fasteners and ensure that only the proper
screws are removed.
10"
(25.4 cm)
29-3/4"
(75.6 cm)
Carefully tighten each screw to secure the
overlay and check to ensure that the overlay is
square with the dishwasher door and cabinet
opening and that the panel doesn’t interfere
with the operation of the dishwasher.
Verify operation of the door counter balance
springs after installation of the overlay panel.
The additional weight of the overlay panel might
require an adjustment to the preload of the
counterbalance springs. If adjustment of the
springs is required, please refer to the “Counter
Balance Spring” section.
Position custom face panel on front of dishwasher.
c
22-21/32"
(57.5 cm)
23-9/32"
(59.1 cm)
NOTE: Back side of panel shown. Use caution not to drill through front of panel.
6
Use non-marring clamps to hold custom panel in place.
Secure with #8 1-3/4”(4.5 cm) long, stainless steel flat
head screws.
7
General Information
General Information
• Read these instructions carefully and
completely before installing the dishwasher.
The installation should be carried out by a
qualified installer, who is familiar with all
local codes and ordinances for electrical
and plumbing connections. If the
dishwasher is being installed for the first
time, most of the work has to be done
before you move it into place. If you are
replacing an old dishwasher, you must
check the old connections.
• Electrical requirements are listed in the
“Specifications” section (page 5).
NOTE: Be sure to run the drain line through
the hole to the sink compartment before
moving the dishwasher into place.
• For service convenience, a shut-off valve
(not supplied) should be installed in the
supply line in a readily accessible location
(such as beneath the sink).
• It is recommended that the dishwasher
be connected to a hot water supply. If a
cold water supply is used, cycle times will
vary.
• It is important that the water supply line and
the shut-off valve have a sufficient flow
volume. Flush the supply line prior to
connecting it to the intake line of the
dishwasher.
• Make sure the connection is sealed and not
leaking before completing the installation.
Site Preparation
NOTE: It is recommended that a thorough
site inspection be conducted PRIOR to
unpacking and moving this appliance.
• After determining where the water
supply line will connect to the
dishwasher, provide a 2” (5.1 cm) access
hole and run the line to the approximate
fill valve location. Sealing access area
once lines are in place is recommended.
• Confirm available access to adequate power.
Drain
• The access hole for the drain line should be
2” square (5.1 cm). Locate as low and as
near to the back wall as possible.
• Do not use any fittings anywhere in the drain
line that are less than 1/2” (1.3 cm) ID.
• If the drain line is going to be connected to
a food waste disposer, be sure to remove
the knockout or plug from the fitting before
connecting drain line.
• Drain connection should be a minimum of 9”
(22.9cm) from the floor. If connection is
lower, siphoning during cycle can occur.
Water Supply
WARNING
CAUTION
Plumbing connections must comply with
applicable sanitary, safety, and plumbing
codes.
The dishwasher has a factory installed
backflow preventer. Do Not add an
additional check valve.
• Water pressure for the water supply should
be a minimum of 10 to 125 psi. The
dishwasher is supplied with a 5’ (1.5 m)
braided stainless steel water line with 3/8”
(0.95 cm) compression fitting connected to
dishwasher.
• After determining where the water supply
line will connect to the dishwasher, provide
a 2” (5.1 cm) access hole and run the water
supply line to the approximate fill valve
location.
NOTE:
The end of the drain hose is
1” (2.5 cm), but is adjustable to 3/4” (1.9 cm) or
5/8” (1.6 cm). If the drain connection is smaller
than 1” (2.5 cm), the hose can be cut to fit the
connection.
8
3. The edges of the opening mentioned in
Item (2) should, if the partition is wood,
be smooth and rounded or, if the
partition is metal, be covered with the
grommet provided for this purpose by
the manufacturer; and
4. Care should be exercised, when the
appliance is installed or removed to
reduce the likelihood of damage to the
power supply cord.
• The dishwasher comes with a 5’ (1.8 m)
electrical cord for 110-120 volts, 15/20 amp
supply. This cord should be plugged into
the 110-120 volt outlet located under the
sink.
• If the cord is not long enough or if a hard
wire installation is needed, follow the
instructions on page 10.
NOTE: Access holes should be 2” square (5.1
cm) with no sharp edges.
Electrical Connections
This appliance must be grounded. In the
event of a malfunction or breakdown,
grounding will reduce the risk of electric
shock by providing a path of least resistance
for electric current. This appliance is
equipped with a cord having an equipmentgrounding conductor and a grounding plug.
The plug must be plugged into an
appropriate outlet that is installed and
grounded in accordance with all local codes
and ordinances.
WARNING
Disconnect the electrical power supply
and place a tag at the disconnect switch
indicating that you are working on the
circuit.
WARNING
Grounding Instructions if Hardwired:
This appliance must be connected to a
grounded metal, permanent wiring system; or
an equipment grounding conductor must be
run with the circuit conductors and connected
to the equipment – grounding terminal or
lead on the appliance.
• For a cord connected undercounter
dishwasher:
1. The power supply receptacle for the
appliance should be installed in a
cabinet or on a wall adjacent to the
under counter space in which the
appliance is to be installed;
2. There should be an opening through the
partition between the compartments
mentioned in Item (1), that is large
enough for the attachment plug to pass
through.
Be sure electrical power is turned off at
circuit breaker or fuse box before
servicing or installing unit. Do not use an
extension cord for this appliance.
WARNING
Improper connection of the equipment –
grounding conductor can result in a risk
of electric shock. Check with a qualified
electrician or serviceman if you are in
doubt as to whether the appliance is
properly grounded. Do not modify the
plug provided with the appliance; if it
will not fit the outlet, have a proper
outlet installed by a qualified electrician.
9
Hardwire Conduit Option
a
b
Trim Installation Options
To install dishwasher without trim, remove the 6 screws and washers (3 per
side) and remove trim. To attach wiper gasket to dishwasher, pull protective
film off adhesive back on wiper gaskets and apply to leading edge of
dishwasher frame.
1a
1
Remove any loose items in the dishwasher and carefully lay
the dishwasher on its back. NOTE: Be careful not to pinch
hoses or power cord beneath dishwasher.
Remove bottom pan and front plate.
Black
c
d
Green
Ground
White
Common
UL approved
strain relief
Loosen ground wire and wires on terminal block.
Loosen strain relief and remove cord.
NOTE: Other items are grounded in this location–these
items must remain grounded.
e
Run wires through bottom pan. Using a UL approved
strain relief, connect wires to terminal block.
1b
Green
Ground
Connect ground wire.
NOTE: Reinstall front plate and bottom pan.
10
11
Trim Installation Options (cont’d.)
Dishwasher will ship with trim installed for panel flush install. If needed,
attach wiper gasket by pulling protective film off adhesive back on wiper
gasket and apply behind hemmed edge of side trim.
Trim Installation Options (cont’d.)
To install dishwasher cabinet flush with trim, remove the 6 screws and washers (3
per side) holding side trim on. Shift the side trim forward. Use rear hole on side
trim and the same hole on dishwasher to reattach trim. If needed, attach wiper
gasket by pulling protective film off adhesive back on wiper gasket and apply
behind hemmed edge of side trim.
2a
3a
2b
3b
12
13
Counter Balance Spring Adjustment - If Necessary
a
b
Installation Procedure
2
1
1
Increase
tension
2
Decrease
tension
1
Disconnect cable from hook.
Set counter balance spring connector in appropriate
location.
c
NOTE: For custom panel
installation the door may
require adjustment to the
preload of the counterbalance
springs. Follow these steps to
adjust the tension.
Carefully lay dishwasher on its back and attach the kick
plate brackets. Screws for the brackets will already be
in the base. NOTE: Be careful not to pinch hoses or
power cord beneath dishwasher.
Using tie strap attached to dishwasher, band water line,
drain line, and power cord together.
4
3
Reconnect cable to hook.
Position unit in front of cutout.
Slide unit into opening; be sure to feed water, electrical
and discharge lines into adjacent cabinet.
6
5
Equal distance
Up
Down
Using a level, adjust to appropriate height. Left and right
adjust side to side and center adjusts front to back.
14
To check level, front to back, pull the top rack half-way
out of unit. The rack should remain stationary and not
move in or out.
15
Installation Procedure (cont’d.)
Installation Procedure (cont’d.)
8
7
11A
Air Gap
11B
Air Gap
Minimum
20”
(50.8 cm)
from floor
Attach screws through trim pieces
into cabinets.
(Discharge with air gap)
Install High Loop Clip, which is provided, a minimum of
20” (50.8 cm) from the floor.
9
(Discharge with food waste disposer and air gap)
12
10A
13
1.0”
(2.5 cm)
Cut here for 5/8”
(1.6 cm)
Cut here for 3/4”
(1.9 cm)
Connect water line.
Plug LED light into dishwasher and install
kick plate.
(Discharge with food waste disposer)
Identify discharge connection size; cut line to correct size
and connect. Clamp if necessary.
10B
(Standard discharge)
16
17
Performance Checklist
Testing for Leaks
Final Preparation
• Remove packaging and parts.
• Some stainless steel parts may have a
plastic protective wrap which must be
peeled off.
• Turn on the water supply and check for
leaks.
Unit Reset
• Turn the power on at breaker/fuse box and
test the dishwasher operation by running a
rinse and hold cycle. (This should take
about 12 minutes.)
• If the unit should need to be reset for any
reason, push and hold the “START” button
for 4 seconds.
• Turn off the electrical power and check for
leaks under the dishwasher.
• Make sure that no kinks have developed in
the drain lines.
Service & Registration
Only authorized replacement parts may be used in performing service on the dishwasher. Do not
repair or replace any part of the appliance unless specifically recommended in the manual. All
other servicing should be referred to a qualified authorized technician.
Record the following information. You will need it if service is ever required. The serial number
and model number for your dishwasher are located on the identification plate mounted on the
bottom left side of the dishwasher door opening.
Model number
Date installed
_________________________________________
_________________________________________
Serial number
Dealer's name
_________________________________________
_________________________________________
Date of purchase
Phone number
_________________________________________
_________________________________________
18
19