CHDD 8694
Cooker Hood
Operating and Installation Instructions
Printed on recycled paper
AEG - putting words into action
2
Contents
Safety warnings
For the user
For the installer
4
4
4
Description of the Appliance
Extractor version
Filter Version
6
6
7
Hood Operation
Using the Remote Control
Setting the Remote Control
Remote Control Maintenance
8
9
9
9
Maintenance and care
Metal grease filter
Open the metal grease filter
Charcoal filter
Changing the light bulb
10
10
11
12
13
What to do if
14
Service and spare parts
15
Guarantee Conditions
16
Technical Details
Mounting accessories included
17
17
Electrical connection
Safety warnings for the electrician
Wall unit mounting
17
17
18
3
Safety warnings
For the user
• The cooker hood is designed to extract unpleasant odours from the
kitchen, it will not extract steam.
• Always cover lighted elements, to prevent excess heat from
damaging the appliance. In the case of oil, gas and coal fired
cookers it is essential to avoid open flames.
• Also, when frying, keep the deep frying pan on the cooker top/
cooker under careful control.
• The hot oil in the frying pan might ignite due to overheating.
• The risk of self-ignition increases when the oil being used is dirty.
• It is extremely important to note that overheating can cause a fire.
• Never carry out any flambé cooking under the hood.
• Always disconnect the unit from the power supply before
carrying out any work on the hood, including replacing the
light bulb (take the cartridge fuse out of the fuse holder or switch
off the automatic circuit breaker).
• It is very important to clean the hood and replace the filter at
the recommended intervals. Failure to do so could cause
grease deposits to build up, resulting in a fire hazard.
For the installer
• When used as an extractor unit, the hood must be fitted with a
150mm diameter hose.
• Should there already be a pipe of diameter 125 mm that ducts to
the outside through the walls or roof, it is possible to use the 150/
125 mm reduction flange provided. In this case the hood will be
slightly more noisy.
• When installing the hood, make sure you respect the following
minimum distance from the top edge of the cooking hob/ring
surfaces:
electric cookers
650 mm
gas cookers
750 mm
coal and oil cookers
800 mm min.
• The national standard on fuel-burning systems specifies a maximum depression of 0.04 bar in such rooms.
• The air outlet must not be connected to chimney flues or combustion gas ducts. The air outlet must under no circumstances be
connected to ventilation ducts for rooms in which fuel-burning
appliances are installed.
4
• It is advisable to apply for authorization from the relevant controlling
authority when connecting the outlet to an unused chimney flue or
combustion gas duct.
The air outlet installation must comply with the regulations laid down
by the relevant authorities.
• When the unit is used in its extractor version, a sufficiently large
ventilation hole must be provided, with dimensions that are
approximately the same as the outlet hole.
• National and regional building regulations impose a number of
restrictions on using hoods and fuel-burning appliances connected
to a chimney, such as coal or oil room-heaters and gas fires, in the
same room.
• Hoods can only be used safely with appliances connected to a
chimney if the room and/or flat (air/environment combination) is
ventilated from outside using a suitable ventilation hole approximately 500-600 cm2 large to avoid the possibility of a depression
being created during operation of the hood.
• If you have any doubts, contact the relevant controlling authority or
building inspector’s office.
• Since the rule for rooms with fuel burning appliances is “outlet hole
of the same size as the ventilation hole”, a hole of 500-600 cm2,
which is to say a larger hole, could reduce the performance of the
extractor hood.
• If the hood is used in its filtering function, it will operate simply and
safely in the above conditions without the need for any of the
aforementioned measures.
• When the hood is used in its extractor function, the following rules
must be followed to obtain optimal operation:
— short and straight outlet hose
— keep bends in outlet hose to a minimum
— never install the hoses with an acute angle, they must
always follow a gentle curve only
— keep the hose as large as possible (preferably the same
diameter as the outlet hole).
• Failure to observe these basic instructions will drastically reduce the
performance and increase the noise levels of the extractor hood.
5
Description of the Appliance
• The cooker hood is designed to extract unpleasant odours from the
kitchen, it will not extract steam.
• The hood is supplied as a filter unit (with charcoal filter already
supplied and fitted) and can also be used with an extractor function
function by removing the charcoal filter.
Extractor version
• The air is discharged to the outside through a pipe, which must be
fitted to connection flange D. Fig. 1.
• Remove the grease filters and remove the Charcoal Filter K from its
housing by unscrewing the two screws that fix it to the hood. Refit
the grease filters. Fig. 2.
• In order to obtain the best performance the hose should have a
diameter equal to the outlet hole.
Should there already be a pipe of diameter 125 mm that ducts to
the outside through the walls or roof, it is possible to use the 150/
125 mm reduction flange provided. In this case the hood will be
slightly more noisy.
D
D
K
Fig. 1
6
Fig. 2
Filter Version
• The air is filtered through an AEG charcoal filter and returned to the
kitchen through the top grill of the outlet pipe.
• You will need an original AEG charcoal filter for the filtering function.
• Fix the deflector E using 2 screws Ø 3,5x6.5 mm. Fig. 3.
• Fix the connection flange G using 2 screws Ø 3,5x6.5 mm. Fig. 3.
E
G
Fig. 3
7
Hood Operation
• Best results are obtained by using a low speed for normal
conditions and high speed when odours are more concentrated.
Turn the hood on a few minutes before you start cooking then you
will get an underpressure in the kitchen. It should be left on after
cooking for about 15 minutes or until all odours have disappeared.
The hood operation may be controlled via the control switches or
with the remote control
The control switches are located on lower side of the chimney.
1
1
2
3
4
2
3
4
5 F
6
-
Hood OFF.
Decreases the speed
Hood ON, Increases the speed
5’/15’ (minutes) timer
push once for 5’ timer, twice for 15’ timer, 3 times to turn the
timer OFF
5 - Filter reset
6 - Light ON/OFF
F - Saturated filter indicator light
- BUTTON 4: Activates and deactivates the timer. Automatically
turns the appliance off at the speed in operation.
LED on = timer activated - Duration 5 or 15 minutes as set.
- BUTTON 5: Once you have replaced the charcoal filters, press
this button for at least 3 seconds until the light turns off
- BUTTON 4+5: Remote control code programming. Keep both
buttons pressed for at least 3 seconds. A beep will sound to
indicate that the programming mode has been accepted.
Without releasing the buttons, press any one of the remote
control buttons. A beep will sound to indicate that the code has
been accepted and stored.
- F LED: Indicates that the charcoal filter is saturated.
This LED is also ON when the hood is used in the extractor
version, press BUTTON 5 until the light turns off.
8
Using the Remote Control
Button 1 = ON / 1st Speed / 2nd Speed / 3rd Speed/4th Speed/OFF
Button 2 = Timer ON/OFF
Button 3 = Light ON/OFF
Setting the Remote Control
Before using the remote control, first
programme it with the hood:
Push Button 4+5, keep both buttons
pressed for at least 3 seconds.
A beep will sound to indicate that the
programming mode has been
accepted.
Without releasing the buttons, press
any one of the remote control buttons.
A beep will sound to indicate that the
code has been accepted and stored.
Remote Control
Maintenance
Button 2
Button 1
Control
Lamp
Button 3
Battery
compartment
cover
Clean the remote control using non
abrasive detergents.
Follow the instructions below in order
to replace the battery for the remote
control :
• Raise the cover on the base of the
remote control, in order to access
the battery compartment.
• Remove the old battery and replace it with a new battery type 23A
12V
• Fit the new battery taking care to check the polarity as indicated on
the base of the battery compartment.
Warning!
If the remote control doesn’t work , do the following before
calling your local AEG Service Force Centre:
• Disconnect the hood from the mains.
• Reconnect the hood to the mains.
• Repeat the procedure described on paragraph “Setting the remote
control”
Follow this procedure whenever the remote control doesn’t work for
any apparent reason (e.g.: dead battery).
9
Maintenance and care
• The hood must always be disconnected from the electricity
supply before beginning any maintenance work.
• Never insert pointed objects in the motor’s protective grid.
• Wash the outside surfaces using a delicate detergent solution.
Never use caustic detergents or abrasive brushes or powders.
• Only ever clean the switch panel and filter grille using a damp cloth
and delicate detergents.
• It is extremely important to clean the unit and change the filters at
the recommended intervals. Failure to do so will cause grease
deposits to build up that could constitute a fire hazard.
Metal grease filter
• The purpose of the grease filters is to aspirate grease particles
which form during cooking and it must always be used, either in the
external evacuation or internal recycling function.
Attention: the metal grease filters must be removed and washed,
either by hand or in the dishwasher, every four weeks.
10
Open the metal grease filter
• First, push both metal grease filter handles towards the centre, then
extract the filter M, pulling downwards. Fig. 4.
Repeat the steps with the second filter.
Hand washing
Soak grease filters for about one hour in hot water with a greaseloosening cleaner, then rinse off thoroughly with hot water. Repeat
the process if necessary. Refit the grease filters when they are dry.
Dishwasher
Place grease filters in the dishwasher. Select most powerful
washing programme and highest temperature, at least 65°C.
Repeat the process. Refit the grease filters when they are dry.
When washing the metal grease filter in the dishwasher a slight
discolouration of the filter can occur, this does not have any impact
on its performance.
• Clean the inner housing using a hot detergent solution only (never
use caustic detergents, abrasive powders or brushes).
Fig. 4
11
Charcoal filter
• The charcoal filter is already supplied and mounted in place.
• The charcoal filter should only be used if you want to use the hood
in its filtering function.
• Only applicable for recirculation. The charcoal filters absorb smells
and odours.
• The charcoal filter cannot be washed nor regenerated.
The charcoal filter should be replaced every 6 months under normal
use.
Replacement filters are available from your local Service Force
Centre.
Fitting the charcoal filter:
• Unplug the unit or disconnect it from the power supply
• Remove the metal grease filter. Fig. 4
• Fit the charcoal filter and fix it to the body of the hood with two
supplied screws. Fig. 5.
• Refit the metal grease filters.
To remove proceed in reverse order.
• Always specify the hood model code number and serial number
when ordering replacement filters. This information is shown on the
registration plate located on the inside of the unit.
• The charcoal filter can be ordered from your local Service Force
Centre.
K
Fig. 5
12
Warning
• Failure to observe the instructions on cleaning the unit and
changing the filters will cause a fire hazard. You are therefore
strongly recommended to follow these instructions.
• The manufacturer declines all responsibility for any damage to the
motor or any fire damage linked to inappropriate maintenance or
failure to observe the above safety recommendations.
Changing the light bulb
•
•
•
•
•
Disconnect the cooker hood from the main supply.
Remove the lamp cover, use a screw driver as a lever. Fig. 6.
Replace the old bulb with a new one of the same type.
Remount the lamp cover.
If the light does not come on, make sure the bulb has been inserted
correctly before contacting your local Service Force Centre.
Fig. 6
13
What to do if
If your appliance fails to work properly please carry out the following
checks.
Symptom
Solution
The cooker hood will not start...
Check that:
The hood is connected to
the electricity supply.
Check that a fan speed has
been selected
The cooker hood is not working
effectively..
Check that:
The fan speed is set high
enough for the task.
The grease filters are clean.
The kitchen is adequately vented
to allow the entry of fresh air.
If set up for recirculation, check
that the charcoal filter is still
effective.
If set up for extraction, check that
the ducting and outlets are not
blocked.
The cooker hood has
switched off during operation...
The safety cut-out device has been
tripped.
Turn off the hob and then wait for
the device to reset.
If the hood has been installed
below the heights indicated in the
installation instructions the motor
will cut-out frequently which will
damage the hood.
If after all these checks, the problem persists, contact your local
Service Force Centre, quoting the model and serial number.
Please note that it will be necessary to provide proof of purchase for
any in-guarantee service calls.
In-guarantee customers should ensure that the above checks have
been made as the engineer will make a charge if the fault is not a
mechanical or electrical breakdown.
14
Service and spare parts
In the event of your appliance requiring service, or if you wish to
purchase spare parts, contact your local AEG Service Force Centre by
telephoning
08705 929 929
Your call will be automatically routed to the Service Centre covering
your post code area.
For the address of your local Service Force Centre and further information about Service Force, please visit the website at
www.serviceforce.co.uk
Please ensure that you have read the section „What to do if....“ as the
engineer will make a charge if the fault is not a mechanical or electrical breakdown even the appliance is under warranty.
Please note that proof of purchase is required for in-guarantee
service calls.
Help us to help you
Please determine your type of enquiry before writing or telephoning.
When you contact us we need to know:
• Your name
• Address and post code
• Telephone number
• Clear and concise details of the fault
• Name and model of the appliance*
• E number*
* This information can be found on the rating plate, which can be seen
when the grease filters are removed.
Customer Care
For general enquiries concerning your AEG appliances, or for further
information on AEG products, please contact our Customer Care
Department at the address below or visit our website at
www.aeg.co.uk
Customer Care Department
AEG Domestic Appliances
55-77 High Street
Slough
Berkshire
SL1 1DZ
Tel.: 08705 350 350*
*
calls to this number may be recorded for training purposes.
15
Guarantee conditions
Guarantee Conditions
AEG offer the following guarantee to the first purchaser of this appliance.
1. The guarantee is valid for 12 months commencing when the appliance is handed
over to the first retail purchaser, which must be verified by purchase invoice or similar
documentation.The guarantee does not cover commercial use.
2. The guarantee covers all parts or components which fail due to faulty workmanship
or faulty materials. The guarantee does not cover appliances where defects or poor
performance are due to misuse, accidental damage, neglect, faulty installation,
unauthorised modification or attempted repair, commercial use or failure to observe
requirements and recommendations set out in the instruction book.This guarantee
does not cover such parts as light bulbs, removable glass-ware or plastic.
3. Should guarantee repairs be necessary the purchaser must inform the nearest
customer service office (manufacturer`s service or authorised agent). AEG reserves
the right to stipulate the place of the repair (i.e.the customer`s home, place of
installation or AEG workshop).
4. The guarantee or free replacement includes both labour and materials.
5. Repairs carried out under guarantee do not extend the guarantee
period for the appliance. Parts removed during guarantee repairs become the
property of AEG.
6. The purchaser`s statutory rights are not affected by this guarantee.
European Guarantee
If you should move to another country within Europe then your guarantee moves with you to
your new home subject to the following qualifications:
- The guarantee starts from the date you first purchased your product.
- The guarantee is for the same period and to the same extent for labour and parts as
exist in the new country of use for this brand or range of products.
- This guarantee relates to you an cannot be transferred to another user.
- Your new home is within the European Community (EC) or European Free Trade
Area.
- The product is installed and used in accordance with our instructions and is only
used domestically, i.e. a normal household.
- The product is installed taking into account regulations in your new country.
Before you move please contact your nearest Customer Care Centre, listed below, to give
them details of your new home.They will then ensure that the local Service Organisation is
aware of your move and able to look after you and your appliances.
France
Senlis
+33 (0) 44 62 29 29
Germany
Nürnberg
+49 (0) 911 323 2600
Italy
Pordenone
+39 (0) 1678 47053
Sweden
Stockholm
+46 (0) 8 738 7910
Slough
+44 (0) 1753 219899
UK
16
Technical Details
Dimensions - extractor version (in cm):
Height - Width - Depth 78,5/120 - 89,8 - 50,5
Maximum absorbed power:
340 W
Motor absorption:
1 x 300 W
Lighting:
2 x 20W
Length of the cable:
120 cm
Mounting accessories included
1 deflector
1 chimney support
1 reduction flange Ø 125-120 mm
1 remote control
1 charcoal filter (already fitted)
1 support bracket
8 wood-screws 5 x 45 mm (for wall mounting - 2 as spare parts)
8 wall plugs Ø 8 mm (for wall mounting - 2 as spare parts)
6 washers (2 for chimney supprot - 2 for lower fixing - 2 as spare
parts)
6 metal screws 3,5 x 9,5 (for chimney, deflector and connection flange
- 2 as spare parts)
2 metal screws 3,5 x 6,5 (for connection block and circuit board
support).
We reserve the right to change specifications and colours as a result
of our policy of continuing technological development.
Electrical connection
Safety warnings for the electrician
The electric outlet should be placed on the wall inside the chimney.
The hood has a power cable, 150 cm, with earth connection and the
rated voltage is 220 - 240 V.
Connect the hood to the mains supply via a double pole switch
which has 3 mm minimum separation between the contacts.
The switch must be accessible at all times.
The following is valid in the United Kingdom only:
- the wire which is coloured green and yellow must be connected to
the terminal which is marked with the letter E or by the earth symbol
(
), or coloured green or green and yellow;
- the wire which is coloured blue must be connected to the terminal
which is marked with the letter N or coloured black, - the wire which is coloured brown must be connected to the terminal
which is marked with the letter L or coloured red.
17
Wall unit mounting - Fig. 7
• Mark the wall with a centre line, this will aid mounting procedure (1),
position the template so that the mid line printed on the template
matches with the centre line previously drawn, the lower side of the
template corresponds to the lower side of the hood once mounted
(2).
• Drill four holes Ø 8mm and fit four wall plugs (3).
• Drill two holes Ø 8mm on the upper side close to the ceilling (4) use
the chimney support as a template, check that the mid of the
chimney support corresponds to the mid of the centre line
previously drawn, fit two wall plugs.
Note: ONLY in case the hood is to be used in filter version, mount
the deflector E on the chimney support and the connection flange G
with two screws each (5).
• Fix the chimney support onto the wall with two screws and washers
(6).
• Hang the hood (7), remove the grease filters and fix it definitively
with two screws and washers (8), check that all four screws are
securely tightened.
• Fit an exhausting pipe (9) to connect the outlet hole D of the hood to
the connection flange G of the deflector E (Filter version) or to the
outside (Extractor version).
• Make electrical connection (10), but leave the hood disconnected
from the mains supply.
• Fix the circuit board and connection block unit on the top side of the
hood with two screws (boxes facing frontwards) (11).
• Place the cable clamp in the corresponding housing (12).
• Position the chimney and secure them in place, first up (13a) to the
chimney support (13b) , then slide it downwards making sure the
cable clamp (step 12) is seated in the housing on chimeny (14) and
that the control buttons match with the corresponding openings
(15).
• Adjust the position of the push-button box using two screws from
the inside of the motor housing (16).
• Fix the lower section of the chimney with two screws from the inside
of the hood (17).
• Refit the grease filters, connect the hood the the home general
electric panel and check if the hood work properly.
18
13a
10
13a
6
13b
4
E
5
G
1
7
9
D 7
2
17
17
8
3
16
15
14
11
12
Fig. 7
19
AEG Hausgeräte GmbH
Postfach 1036
D-90327 Nürnberg
http://www.aeg.co.uk
© Copyright by AEG
LI1ØBA Ed. 07/02
TØ8Ø4