Cub Cadet | 1212 | Series 1000 and 1500

Series 1000 and 1500
Series 1000 and 1500
1.
INTRODUCTION
1.5.
Refer to the table provided for engine applications in the 1000 series range. See Figure 1.5.
1000 Series Engine Applications
Year Model # Factory #
Engine
2001 1027
13A-328-101 9.0 HP BS
1170 13CD608G101 17.5 HP BS
1180 13AT608H101 18 HP BS
1212 14AJ808H101 21 HP BS
Disclaimer: This service manual is intended to be
used by trained technicians.
Disclaimer: The information contained in this manual
is current and accurate at the time of writing, but is subject to change without notice.
1.1.
Intent: This manual is intended to:
•
Provide specific service and repair procedures
for a range of Cub Cadet 1000 and 1500 Series
tractors manufactured for the 2005/2006 season.
•
Highlight significant changes to the Cub Cadet
1000 Series since it’s introduction.
1.2.
Engines: A variety of single cylinder and V-twin
engines have been used in the 1000 series tractors. Kohler Courage line of single-cylinder and
V-Twin engines is presently the most heavily
used power source in the 1000 Series line
1.3.
For specific engine service information, refer to
the engine manufacturer’s service publications.
1.4.
The engine is partially identified by the 4th digit
of the factory number:
•
13AX11CG756 - Kohler Courage single cylinder
•
13AP11CP756 - Kohler courage V-Twin
2002
1027
1170
1515
1517
13A-328-101
13CD608G101
13A-201F100
13A-231G100
2003
1525
1527
1529
13A-221F100 15 HP KAW
13A-241G100 17 HP KAW
13A-261H100 19 HP KAW
2004 LT 1018
LT 1022
LT 1024
GT 1222
13AL11CG710 18.5 HP BS
13AB11CH710 22 HP BS
13AR11CP710 24 HP BS
14AB13CH710 22 HP BS
2005 LT 1042 13BX11CG710
LT 1045 13AX11CH710
LT 1046 13AP11CH710
LT 1050 13AQ11CP710
SLT 1554 13AK11CK710
19 HP KOH
20 HP KOH
23 HP KOH
26 HP KOH
27 HP KOH
2006 LT 1042 13AX11CG756
LT 1045 13AX11CH756
LT 1050 13AP11CP756
SLT 1550 13AQ11BP756
GT 1554 14AK13BK756
19 HP HOH
20 HP KOH
23 HP KOH
25 HP KOH
27 HP KOH
Figure 1.5
1
9.0 HP BS
17.5 HP BS
15 HP KOH
17 HP KOH
Series 1000 and 1500
1.6.
Decks: Cutting decks ranging in width from 38”
to 54” have been used on the 1000 Series platform.
1.9.
1.7.
There have been multiple versions of some
decks, most particularly the 42”. Check the serial
number when researching for parts or service
information.
1.8.
The deck size is identified by the 8th digit of the
factory number: See Figure 1.8.
1.10. A Two-belt CVT system driving an MTD singlespeed transaxle is presently used only on the
LT1040 model. This system can be distinguished by the gear selector (F-N-R) on the left
rear fender, and the simple drive pedal.
See Figure 1.10.
Year
2001
Drive Systems: A variety of hydrostatic and
CVT drive systems have been used on the 1000
Series tractors.
1000 Series Deck Applications
Width
Deck
Deck/PTO Belts
27.5"
CYB/STD 754-0754
42"
G
754-0472
46"
H
754-0349/754-0476
2002
27.5"
42"
38"
42"
CYB/STD
G
F
G
754-0754
754-0472
754-0641
754-0645/754-0644
2003
38"
42"
46"
F
G
H
754-0641
754-0645/754-0644
754-04011
2004
42"
46"
50"
G
H
P
754-0498/754-0499
754-04033
754-04048
42"
46"
50"
54"
G
H
P
K
754-04060B
754-04033
754-04077
754-0642
42"
46"
50"
54"
G
H
P
K
754-0349
754-0349
754-0349
754-0349
Figure 1.10
2005
2006
1.11. A similar two-belt CVT system was employed to
drive a heavy-duty transaxle in some 2002 and
2002 models having two forward speed ranges.
These are easy to identify by the presence of the
gear selector lever between the operators knees
rather than on the fender.
1.12. All CVT driven 1000 and 1500 Series tractors
have a gear selector lever and a drive pedal on
the right side, near the brake pedal.
1.13. All Hydrostatic transaxles on the 1000 and 1500
Series are operated by a rocker pedal on the
right side, near the brake pedal.
Figure 1.8
•
13AX11CG756 - 42” 2-blade deck
•
13AX11CH756 - 46” 3-blade deck
•
13AP11CP756 - 50” 3-blade deck
•
13AQ11BP756 - 50” 3-blade deck
•
14AK13BK756 - 54” 3-blade deck
1.14. A Hydro-Gear 310-0510 hydrostatic transaxle is
used on LT models having 20” rear tires. Hydrostatic transaxles have a rocker pedal to control
forward and reverse direction and speed.
2
Series 1000 and 1500
1.15. A Hydro-Gear 314-0610 hydrostatic transaxle
with a different final drive ratio is used on LT
models having 22” rear tires. Hydrostatic transaxles have a rocker pedal to control forward
and reverse direction and speed. See Figure
1.15.
2.
NEW HOOD DESIGN
2.1.
Early 1000 and 1500 Series tractors used a variety of steel hoods and side panels. Later ones
resembled those used on the 2000 and 2500
Series tractors.
2.2.
The hood presently used on the 1000 series
tractors is a molded 1-piece design. See Figure
2.2.
Figure 1.15
1.16. A Hydro-Gear 320-3000 hydrostatic transaxle is
used on GT designated models. This is a substantially heavier duty IHT than the one used in
the LT models. Hydrostatic transaxles have a
rocker pedal to control forward and reverse
direction and speed. See Figure 1.16.
Figure 2.2
2.3.
The 1000 Series hood opens from the back.
See Figure 2.3.
Figure 2.3
Figure 1.16
3
Download PDF