Ransomes | Magna 250 | Operating instructions | Ransomes Magna 250 Operating instructions

24199G-GB (rev.4)
®
Safety Operation & Maintenance Manual
Ransomes Parkway 2250 Plus Ride On Reel Mower
Series: WB - Engine type: Kubota V1505
Product code: LGNN040
WARNING: If incorrectly used this machine can cause severe
injury. Those who use and maintain this machine should be
trained in its proper use, warned of its dangers and should
read the entire manual before attempting to set up, operate,
adjust or service the machine.
GB
United
Kingdom
RJL 100 January 2010
© 2010, Ransomes Jacobsen Limited. All Rights Reserved
1
CONTENTS
CONTENTS
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
PAGE
CONTENTS
2
2.1
2.2
INTRODUCTION
IMPORTANT ............................................................. 2
PRODUCT IDENTIFICATION .................................... 2
7
7.1
7.2
3
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
SAFETY INSTRUCTIONS
OPERATING INSTRUCTIONS .................................. 3
SAFETY SIGNS ....................................................... 3
STARTING THE ENGINE ......................................... 3
DRIVING THE MACHINE ......................................... 3
TRANSPORTING ...................................................... 3
LEAVING THE DRIVING POSITION ........................ 4
SLOPES .................................................................. 4
BLOCKED CUTTING CYLINDERS ........................... 4
ADJUSTMENTS, LUBRICATION AND
MAINTENANCE ........................................................ 4
GUIDELINES FOR THE DISPOSAL OF SCRAP
PRODUCTS .............................................................. 7
7.3
7.4
7.5
7.6
7.7
7.8
3.10
4
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.7
4.9
SPECIFICATIONS
ENGINE SPECIFICATION ........................................ 8
MACHINE SPECIFICATION ..................................... 8
VIBRATION LEVEL .................................................. 9
SLOPES .................................................................. 9
RECOMMENDED LUBRICANTS ............................. 9
CUTTING PERFORMANCE ..................................... 9
CUTTING PERFORMANCE (AREA) ........................ 9
DIMENSIONS .......................................................... 10
CONFORMITY CERTIFICATES ............................... 12
5
5.1
5.2
DECALS
SAFETY DECALS .................................................. 20
INSTRUCTION DECALS ......................................... 20
6
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
6.9
6.10
6.11
6.12
6.13
6.14
CONTROLS
STARTER SWITCH ................................................. 21
THROTTLE CONTROL LEVER ............................... 21
STEERING WHEEL RAKE ADJUSTMENT ............. 21
FOOTPEDAL ........................................................... 21
SPEED LIMITER ..................................................... 21
TRANSPORT LATCHES ......................................... 22
PARKING BRAKE ................................................... 22
HYDRAULIC LIFT LEVERS .................................... 22
UNIT COUNTER BALANCE CONTROL .................. 22
CUTTING UNIT SWITCHES .................................... 23
VARIABLE CYLINDER SPEED .............................. 23
BACKLAPPING LEVER .......................................... 23
INSTRUMENT PANEL ............................................. 24
DIFF LOCK CONTROL ............................................ 25
PAGE
7.12
OPERATION
DAILY INSPECTION ................................................ 26
OPERATOR PRESENCE AND SAFETY INTERLOCK
SYSTEM ................................................................. 27
OPERATING PROCEDURE .................................... 28
STARTING THE ENGINE ........................................ 29
DRIVING .................................................................. 29
MOWING ................................................................. 29
TO STOP THE ENGINE .......................................... 29
PUSHING THE MACHINE WITH THE ENGINE
STOPPED ............................................................... 31
MOWING ON SLOPES ........................................... 32
8
8.1
8.2
8.3
8.4
8.5
8.6
8.7
8.8
8.9
8.10
LUBRICATION & MAINTENANCE
MAINTENANCE CHART ......................................... 36
DAILY CHECKS (Every 8 working hours) ............... 37
MACHINE: Every 400 Working Hours. ................... 38
MACHINE: Every 800 Working Hours. ................... 38
HYDRAULIC TEST POINTS. ................................... 38
ENGINE MAINTENANCE - Fuel System ................ 39
ENGINE MAINTENANCE - Air Filter ....................... 40
ENGINE MAINTENANCE - Battery ......................... 41
MACHINE MAINTENANCE ..................................... 41
END OF SEASON .................................................. 42
9
9.3
9.1
9.2
9.4
9.5
9.6
9.6.2
9.6.3
ADJUSTMENT
COOLING FAN BELT .............................................. 43
SPEED LIMITER. .................................................... 43
ALTERNATOR/WATER PUMP ................................ 43
HEIGHT OF CUT ..................................................... 44
BACKLAPPING ....................................................... 45
GENERAL INSTRUCTIONS FOR
GRAMMER SEATS ................................................. 46
SEAT MSG75 .......................................................... 47
SEAT MSG85 .......................................................... 50
10
10.1
10.2
TROUBLESHOOTING
GENERAL ............................................................... 52
QUALITY OF CUT ................................................... 53
11
FUSES AND RELAYS ............................................ 61
12
GUARANTEE / SALES & SERVICE ...................... 63
en-1
2
INTRODUCTION
2.1
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
IMPORTANT
IMPORTANT: This is a precision machine and the service obtained from it depends on the way it is
operated and maintained.
This SAFETY AND OPERATORS MANUAL should be regarded as part of the machine. Suppliers of both
new and second-hand machines are advised to retain documentary evidence that this manual was provided
with the machine.
This machine is designed solely for use in customary grass cutting operations. Use in any other way is
considered as contrary to the intended use. Compliance with and strict adherence to the conditions of
operation, service and repair as specified by the manufacturer, also constitute essential elements of the
intended use.
Before attempting to operate this machine, ALL operators MUST read through this manual and make
themselves thoroughly conversant with Safety Instructions, controls, lubrication and maintenance.
Accident prevention regulations, all other generally recognized regulations on safety and occupational
medicine, and all road traffic regulations shall be observed at all times.
Any arbitrary modifications carried out on this machine may relieve the manufacturer of liability for any resulting damage
or injury.
2006/42/EC
These are the Original instructions verified by Ransomes Jacobsen Limited.
.
2.2
A
B
C
D
E
F
G
H
J
PRODUCT IDENTIFICATION
West Road
Ransomes Europark
Ipswich IP3 9TT
England
Maximum front axle load in Kg (for
machines being driven on the highway)
Gross weight (mass) in Kg
Maximum rear axle load in Kg (for
machines being driven on the highway)
Power in Kw
Date code
Machine type (Designation)
Product code
Product name
Serial number
A
Kg
Serial Plate Location
The serial plate A is located on the chassis under
the operators seating position.
A
en-2
B
Kg
F
H
C
Kg
D
Kw
E
G
J
2
2.3
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
INTRODUCTION
KEY NUMBERS
It is recommended that all key numbers are noted here:
Starter Switch :-
____________________________________________
Diesel tank :-
____________________________________________
It is also recommended that the machine and engine numbers are recorded.
The machine serial number is located on the registration plate and the engine serial number can be found
under the exhaust maifold above the starter motor.
Machine Number :-
____________________________________________
Engine Number :-
____________________________________________
2.4
Spares Stocking Guide
To keep your equipment fully operational and productive, Ransomes suggests you maintain a stock of the more
commonly used maintenance items.
We have included part numbers for the additional support materials and training aids.
Service Support Material
Part No
Description
24821E
Service Parts Catalogue
24870G
Parkway 2250 Plus Parts Manual
97898-03340
Kubota Engine Parts Manual
16622-8916-2
Kubota Engine Operators Manual
97897-00880
Kubota Engine Service Manual
en-3
3
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
SAFETY INSTRUCTIONS
This safety symbol indicates important safety
messages in this manual. When you see this
symbol, be alert to the possibility of injury, carefully
read the message that follows, and inform other
operators.
•
3.1 OPERATING INSTRUCTIONS
•
Ensure that the instructions in this book
are read and fully understood.
•
No person should be allowed to operate
this machine unless they are fully
acquainted with all the controls and the
safety procedures.
•
Never allow children or people unfamiliar
with these instructions to use this
machine. Local regulations may restrict
the age of the operator.
•
3.2 SAFETY SIGNS
•
It is essential all safety labels are kept
legible, if they are missing or illegible they
must be replaced. If any part of the
machine is replaced and it originally
carried a safety label, a new label must be
affixed to the replacement part. New
safety labels are obtainable from
Ransomes dealers.
•
3.3 STARTING THE ENGINE
•
Before starting the engine check that the
brakes are applied, drives are in neutral,
guards are in position and intact, and
bystanders are clear of the machine.
•
Do not run the engine in a building without
adequate ventilation.
3.4 DRIVING THE MACHINE
•
Before moving the machine, check to
ensure that all parts are in good working
order, paying particular attention to
brakes, tyres, steering and the security of
cutting blades.
•
Replace faulty silencers, mow only in
daylight or good artificial light
•
Always observe the Highway Code both
on and off the roads. Keep alert and
aware at all times. Watch out for traffic
when crossing or near roadways.
•
Stop the blades rotating before crossing
surfaces other than grass.
en-4
•
•
•
•
•
•
Remember that some people are deaf or
blind and that children and animals can
be unpredictable.
Keep travelling speeds low enough for
an emergency stop to be effective and
safe at all times, in any conditions.
Remove or avoid obstructions in the
area to be cut, thus reducing the
possibility of injury to yourself and/or
bystanders.
When reversing, take special care to
ensure that the area behind is clear of
obstructions and/or bystanders. DO
NOT carry passengers.
Keep in mind that the operator or user is
responsible for accidents or hazards
occurring to other people or their
property.
When the machine is to be parked,
stored or left unattended, lower the
cutting means unless the transport locks
are being used.
While mowing, always wear substantial
footwear and long trousers. Do not
operate the equipment when barefoot or
wearing open sandals.
Check the grass catcher frequently for
wear or deterioration. After striking a
foreign object. Inspect the lawnmower
for damage and make repairs before
restarting and operating the equipment.
If the machine starts to vibrate
abnormally, check immediately.
3.5 TRANSPORTING
•
Ensure that the cutting units are
securely fastened in the transport
position. Do not transport with cutting
mechanism rotating.
•
Drive the machine with due
consideration of road and surface
conditions, inclines and local
undulations.
•
Sudden decelerating or braking can
cause the rear wheels to lift.
•
Remember that the stability of the rear
of the machine is reduced as the fuel is
used.
3
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
SAFETY INSTRUCTIONS
3.6 LEAVING THE DRIVING POSITION
•
Park the machine on level ground.
•
Before leaving the driving position, stop
the engine and make sure all moving parts
are stationary. Apply brakes and
disengage all drives. Remove the starter
key.
3.7 SLOPES
TAKE EXTRA CARE WHEN WORKING ON
SLOPES
•
Local undulations and sinkage will change
the general slope. Avoid ground conditions
which can cause the machine to slide.
•
Keep machine speeds low on slopes and
during tight turns.
•
Sudden decelerating or braking can
cause the rear wheels to lift. Remember
there is no such thing as a “safe” slope.
•
Travel on grass slopes requires particular
care.
DO NOT USE ON SLOPES GREATER THAN 15°
IMPORTANT: When working on any slope set the
weight transfer, if fitted to its maximum (+) setting.
3.8 BLOCKED CUTTING CYLINDERS
•
Stop the engine and make sure all moving
parts are stationary.
•
Apply brakes and disengage all drives.
•
Release blockages with care. Keep all parts
of the body away from the cutting edge.
Beware of energy in the drive which can
cause rotation when the blockage is released.
•
Keep other people away from the cutting
units as rotation of one cylinder can cause
the others to rotate.
3.9 ADJUSTMENTS, LUBRICATION AND
MAINTENANCE
All vehicles
•
Stop the engine and make sure all moving
parts are stationary.
•
Apply brakes and disengage all drives.
•
Read all the appropriate servicing
instructions.
•
Use only the replacement parts supplied by
the original manufacturer.
•
When adjusting the cutting cylinders take
care not to get hands and feet trapped when
rotating cylinders.
•
Make sure that other people are not touching
any cutting units, as rotation of one cylinder
can cause the others to rotate.
•
•
•
•
•
•
•
To reduce the fire hazard, keep the engine,
silencer and battery compartments free of
grass, leaves or excessive grease.
Replace worn or damaged parts for safety.
When working underneath lifted parts or
machines, make sure adequate support Is
provided.
Do not dismantle the machine without
releasing or restraining forces which can
cause parts to move suddenly.
Do not alter engine speed above maximum
quoted in Engine Specification. Do not
change the engine governor settings or
overspeed the engine. Operating the engine
at excessive speed may increase the hazard
of personal injury.
When servicing batteries, DO NOT SMOKE,
and keep naked lights away.
Do not place any metal objects across the
terminals.
Diesel & Petrol vehicles
•
When refuelling, STOP THE ENGINE, DO
NOT SMOKE. Add fuel before starting the
engine, never add fuel while the engine is
running.
•
Use a funnel when pouring fuel from a can
into the tank.
•
Do not fill the fuel tank beyond the bottom of
the filler neck.
•
Replace all fuel tank and container caps
securely.
•
Store fuel in containers specifically designed
for this purpose.
•
Refuel outdoors only and do not smoke while
refuelling.
•
If fuel is spilled, do not attempt to start the
engine but move the machine away from the
area of spillage and avoid creating any
source of ignition until fuel vapours have
dissipated.
•
Allow the engine to cool before storing in any
enclosure.
•
Never store the equipment with fuel in the
tank inside a building where fumes may
reach an open flame or spark.
•
If the fuel tank has to be drained, this should
be done outdoors.
•
Do not spill fuel onto hot components.
en-5
3
SAFETY INSTRUCTIONS
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
DANGER - Indicates an imminently hazardous
situation which, if not avoided, WILL result in
death or serious injury.
WARNING
WARNING - Indicates a potentially hazardous
situation which, if not avoided, COULD result in
death or serious injury.
Batteries produce explosive gases and
contain corrosive acid and supply levels
of electrical current high enough to cause
burns.
CAUTION - Indicates a potentially hazardous
situation which, if not avoided, MAY result in minor
or moderate injury and property damage. It may
also be used to alert against unsafe practices.
IMPORTANT: Transport speed is for highway
use only. Never select transport speed on
grass areas or uneven or unsurfaced roads or
tracks.
WARNING
Battery posts, terminals and related
accessories contain lead and lead
compounds
WASH HANDS AFTER HANDLING
The operating Instructions for the Cutting Units are
contained in a separate Publication .
WARNING
WARNING
Hydraulic Fluid escaping under pressure
can penetrate skin and do serious
damage. Immediate medical assistance
must be sought.
Cutting Unit Transport Latches are a
Secondary Safety Devise.
When Transporting the machine the
Cutting units should be held in the
Transport position on the Hydraulics with
the Transport Latches Engaged.
1. Park the machine on level ground.
WARNING
DO NOT USE ON SLOPES GREATER THAN 15°
WARNING
VENTING GAS CAN CAUSE FROST BITE
WARNING
California Proposition 65
Engine Exhaust, some of its constituents,
and certain vehicle components contain
or emit chemicals known to the state of
California to cause cancer and birth
defects or other reproductive harm.
en-6
2. Whilst seated in the driving position
With the engine at operating speed
raise the cutting units fully by
operating lift levers, return the lever to
the neutral position.
DO NOT move the lever into the
lower position.
3. Disengage drives, stop the engine and
make sure all moving parts are
stationary. Apply brakes and remove
the starter key.
4. Transport latches can now be engaged
or released.
Before releasing transport latches
it is important that all cutting units
are fully raised.
3
SAFETY INSTRUCTIONS
3.10 GUIDELINES FOR THE DISPOSAL
OF SCRAP PRODUCTS
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
•
Other worn out items should be
separated into material groups for
recycling and disposal consistent with
available facilities. More common
separation types are as follows:
• Steel
• Non ferrous metals
• Aluminium
• Brass
• Copper
• Plastics
• Identifiable
• Recyclable
• Non recyclable
• Not identified
• Rubber
•
Items that cannot be separated
economically into different material
groups should be added to the
‘General waste’ area.
•
Do not incinerate waste.
When it has been identified that a turf care
product has no further functional value and
requires disposal, the following actions should
be taken.
These guidelines should be used in conjunction
with applicable Health, Safety and
Environmental legislation and use of approved
local facilities for waste disposal and recycling.
• Position the machine in a suitable
location for any necessary lifting
equipment to be used.
•
•
Use appropriate tools and Personal
Protective Equipment (PPE) and take
guidance from the technical manuals
applicable to the machine.
Remove and store appropriately:
1. Batteries
2. Fuel residue
3. Engine coolant
4. Oils
•
Disassemble the structure of the
machine referring to the technical
manuals where appropriate. Special
attention should be made for dealing
with ‘stored energy’ within pressurised
elements of the machine or tensioned
springs.
•
Any items that still have a useful
service life as second hand
components or can be re-serviced
should be separated and returned to
the relevant centre.
Finally update machinery records to indicate
that the machine has been taken out of service
and scrapped.
en-7
4
SPECIFICATIONS
4.1
ENGINE SPECIFICATION
TYPE:
Kubota 28Kw @ 3000rpm, 4
cylinder (in-line) vertical Diesel
engine, 4-stroke, water cooled,
1498cc, with 12v electric start.
Model:
V1505-BBS-EC-1
Maximum Speed: 3000 +/-50 RPM (No load)
Idle Speed:
1500 +100/ -0 RPM
Oil Sump Capacity: 6.4 litres
Fuel:
No. 2-D Diesel fuel (ASTM D975)
Coolant Capacity: 5 litres 50/50 Anti-freeze
Coolant Specification:
Ethylene glycol anti-freeze with
softened water.
4.2
MACHINE SPECIFICATION
Frame construction:
Heavy duty formed steel chassis.
Transmission:
Hydrostatic power provided by a
servo-controlled transmission
pump. Driving 4 indivdual wheel
motors.
Selectable forward all wheel drive
lock and reverse front axle diff
lock facility.
Cutting unit drive:
Hydraulic, with forward, neutral,
reverse control valve.
Electric dash mounted switch for
on/off control, with floor mounted
switch for cyclinder engage.
Hand control valve for reel speed
adjustment
Speeds:
Cutting:
Transport:
Reverse:
12 km/h
25 km/h
6 km/h
Steering:
Hydrostatic powered steering to
rear wheels.
Ground pressure:
1.0 kg/cm
Brakes, Service:
Positive hydrostatic braking.
Parking: Fail safe, Oil immersed wet disc
brakes.
Battery:
en-8
Exide 093
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
4
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
SPECIFICATIONS
4.3
VIBRATION
4.6 CUTTING PERFORMANCE
The machine was tested for whole body and hand/
arm vibration levels. The operator was seated in the
normal operating postion with both hands on the
steering mechanism. The engine was running and
the cutting device was rotating with the machine
stationary.
Standard ISO 5349: 1986 Mechanical vibration.
Guidelines for the measurement and the assessment
of human exposure to hand-transmitted vibration
Max LH or RH
Parkw ay 2250 Plus
Series WB
Hand / Arm Acceleration
level
Accelerations m/s
45 cuts per meter at 12 km/hr with 8 knife floating
head units.
62 cuts per meter at 12km/hr with 11 knife floating
head units.
23 cuts per meter at 12 km/hr with 4 knife fixed
head units.
34 cuts per meter at 12 km/hr with 6 knife fixed
head units.
4.7 CUTTING PERFORMANCE (AREA)
2
X Aeq
Y Aeq
Z Aeq
0,346
0,394
0,337
2.3 Hectares/hour at 12 km/hr with float head units.
2.3 Hectares/hour at 12 km/hr with fixed head units.
Dominant Value
0,394
Standard ISO 2631-1: 1985 Evaluation of human
exposure to whole body vibration -- Part 1: General
requirements.
Parkw ay 2250
Plus
SeriesWB
Whole Body
Acceleration
level
Mean
4.4
A 10% allowance is included for normal overlaps
and turning at the end of each cut.
Seat Location
Floor Location
Accelerations m/s
2
Accelerations m/s
2
x
y
z
x
y
z
0.0253
0.0200
0.0700
0.0219
0.0125
0.0253
SLOPES
DO NOT USE ON SLOPES GREATER THAN 15°
The slope 15° was calculated using static stability
measurements according to the requirements of
EN 836.
4.5
RECOMMENDED LUBRICANTS
Engine oil:
Should be to MIL-L-2104C or to
A.P.I. Classification SE/SF/SG
grades. [10W-30]
TEMPERATURE
OIL VISCOSITY
ABOVE 4°C (39°F)
S A E 30
BELOW 4°C (39°F)
SAE5W-30 or 10W-30
Hydraulic Oil:
ISO VG46, or equivilant
Grease:
K NATE (RJL No. 4213860), or
equivalent to MIL-G-23549C,
MIL-G-2345C, DIN 51 825,
DIN 51 818.
en-9
4
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
SPECIFICATIONS
4.8
DIMENSIONS
A
Width of cut
214 cm
B
Transport width
160 cm
C
Overall height without ROPS
148.5 cm
D
Overall height with ROPS, add
69.5 cm
E
Overall height with ROPS Cab
215.5 cm
F
Overall length ROPS Frame up
268 cm
G
Overall length ROPS Frame down, add
31 cm
H
Weight of Machine -with Sport 200l
1360 kg*
J
Weight of Machine - With Magna 250
1380 kg*
K
Weight of Sport 200 6 Knife Floating Cutting Unit (each)
L
Weight of Sport 200 8 Knife Floating Cutting Unit (each)
M
Weight of Magna 250 4 Knife Fixed Cutting Unit (each
N
Weight of Magna 250 6 Knife Fixed Cutting Unit (each
P
Weight of Magna 250 8 Knife Fixed Cutting Unit (each
Q
Weight of ROPS
R
Weight of Lighting Kit
S
Weight of Beacon Kit
T
Wheel Track
135.4 cm
U
Wheel Base
149 cm
V
Uncut Circle (Radius)
75 cm
88.6 kg
* With 6 knife fixed head magna units, full fuel tank,
and optional Lighting and Beacon kits
TYRE PRESSURES
Front Wheel
Rear Wheel
Product
Tyre Size
Parkway 2250 Plus
en-10
26 x 12.00 - 12
Tyre Type
Tyre Pressure
Titan Multi Trac 6pr
14 - 20 psi
1.00 - 1.37 bar
Maxxis Turfmaxx (Kevlar)
tread pattern C-165s 4pr
20 - 22 psi
1.37 - 1.50 bar
Tyre Size
20 x 10.00 - 8
Tyre Type
Tyre Pressure
Titan Multi Trac 4pr
14 - 20 psi
1.00 - 1.37 bar
Maxxis Turfmaxx (Kevlar)
tread pattern C-165s 4pr
20 - 22 psi
1.37 - 1.50 bar
4
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
SPECIFICATIONS
U
B
T
E
F
G
D
C
en-11
4
SPECIFICATIONS
4.9
CONFORMITY CERTIFICATES
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
DECLARATION OF CONFORMITY ƒ ȾȿɄɅȺɊȺɐɂə ɁȺ ɋɔɈɌȼȿɌɋɌȼɂȿ ƒ PROHLÁŠENÍ O SHODċ ƒ
OVERENSSTEMMELSESERKLÆRING ƒ CONFORMITEITSVERKLARING ƒ VASTAVUSDEKLARATSIOON ƒ
VAATIMUSTENMUKAISUUSVAKUUTUS ƒ DECLARATION DE CONFORMITE ƒ KONFORMITÄTSERKLÄRUNG ƒ ǻǾȁȍȈǾ
ȈȊȂȂȅȇĭȍȈǾȈ ƒ MEGFELELėSÉGI NYILATKOZAT ƒ DICHIARAZIONE DI CONFORMITÀ ƒ ATBILSTƮBAS DEKLARƖCIJA ƒ
ATITIKTIES DEKLARACIJA ƒ DIKJARAZZJONI TAL-KONFORMITÀ ƒ DEKLARACJA ZGODNOĝCI ƒ DECLARAÇÃO DE
CONFORMIDADE ƒ DECLARAğIE DE CONFORMITATE ƒ VYHLÁSENIE O ZHODE ƒ IZJAVA O SKLADNOSTI ƒ DECLARACIÓN DE
CONFORMIDAD ƒ DEKLARATION OM ÖVERENSSTÄMMELSE ƒ SAMRÆMISYFIRLÝSING ƒ KONFORMITETSERKLÆRING
Business name and full address of the manufacturer ƒ Ɍɴɪɝɨɜɫɤɨ ɢɦɟ ɢ ɩɴɥɟɧ ɚɞɪɟɫ ɧɚ ɩɪɨɢɡɜɨɞɢɬɟɥɹ ƒ
Obchodní jméno a plná adresa výrobce ƒ Producentens firmanavn og fulde adresse ƒ Bedrijfsnaam en volledig adres van de fabrikant ƒ Tootja ärinimi ja täielik aadress ƒ
Valmistajan toiminimi ja täydellinen osoite ƒ Nom commercial et adresse complète du fabricant ƒ Firmenname und vollständige Adresse des Herstellers ƒ ǼʌȦȞȣȝȓĮ țĮȚ
IJĮȤȣįȡȠȝȚțȒ įȚİȪșȣȞıȘ țĮIJĮıțİȣĮıIJȒ ƒ A gyártó üzleti neve és teljes címe ƒ Ragione sociale e indirizzo completo del fabbricante ƒ UzƼƝmuma nosaukums un pilna ražotƗja
adrese ƒ Verslo pavadinimas ir pilnas gamintojo adresas ƒ Isem kummerƛjali u indirizz sƫiƫ tal-fabbrikant ƒ Nazwa firmy i peãny adres producenta ƒ Nome da empresa e endereço
completo do fabricante ƒ Denumirea comercială úi adresa completă a producătorului ƒ Obchodný názov a úplná adresa výrobcu ƒ Naziv podjetja in polni naslov proizvajalca ƒ
Nombre de la empresa y dirección completa del fabricante ƒ Tillverkarens företagsnamn och kompletta adress ƒ Fyrirtækisheiti og fullt heimilisfang framleiðanda ƒ Firmanavn og
full adresse for produsenten
Ransomes Jacobsen Limited
West Road, Ransomes Europark,
Ipswich, England, IP3 9TT
Product Code ƒ Ʉɨɞ ɧɚ ɩɪɨɞɭɤɬɚ ƒ Kód výrobku ƒ Produktkode ƒ Productcode ƒ Toote kood ƒ Tuotekoodi ƒ Code produit ƒ Produktcode ƒ ȀȦįȚțȩȢ ʌȡȠȧȩȞIJȠȢ ƒ Termékkód ƒ
Codice prodotto ƒ Produkta kods ƒ Produkto kodas ƒ Kodiƛi tal-Prodott ƒ Kod produktu ƒ Código do Produto ƒ Cod produs ƒ Kód výrobku ƒ Oznaka proizvoda ƒ Código de producto
ƒ Produktkod ƒ Vörunúmer ƒ Produktkode
LGNN040
Machine Name ƒ ɇɚɢɦɟɧɨɜɚɧɢɟ ɧɚ ɦɚɲɢɧɚɬɚ ƒ Název stroje ƒ Maskinnavn ƒ Machinenaam ƒ Masina nimi ƒ Laitteen nimi ƒ Nom de la machine ƒ Maschinenbezeichnung ƒ
ȅȞȠȝĮıȓĮ ȝȘȤĮȞȒȝĮIJȠȢ ƒ Gépnév ƒ Denominazione della macchina ƒ IekƗrtas nosaukums ƒ Mašinos pavadinimas ƒ Isem tal-Magna ƒ Nazwa urządzenia ƒ Nome da Máquina ƒ
Numele echipamentului ƒ Názov stroja ƒ Naziv stroja ƒ Nombre de la máquina ƒ Maskinens namn ƒ Heiti tækis ƒ Maskinnavn
Designation ƒ ɉɪɟɞɧɚɡɧɚɱɟɧɢɟ ƒ Oznaþení ƒ Betegnelse ƒ Benaming ƒ Nimetus ƒ Tyyppimerkintä ƒ Pažymơjimas ƒ
Bezeichnung ƒ ȋĮȡĮțIJȘȡȚıȝȩȢ ƒ Megnevezés ƒ Funzione ƒ ApzƯmƝjums ƒ Lithuanian ƒ Denominazzjoni ƒ Oznaczenie ƒ
Designação ƒ SpecificaĠie ƒ Oznaþenie ƒ Namen stroja ƒ Descripción ƒ Beteckning ƒ Merking ƒ Konstruksjon
Serial Number ƒ ɋɟɪɢɟɧ ɧɨɦɟɪ ƒ Sériové þíslo ƒ Serienummer ƒ Serienummer ƒ Seerianumber ƒ Valmistusnumero ƒ Numéro de série ƒ Seriennummer ƒ ȈİȚȡȚĮțȩȢ ĮȡȚșȝȩȢ ƒ
Sorozatszám ƒ Numero di serie ƒ SƝrijas numurs ƒ Serijos numeris ƒ Numru Serjali ƒ Numer seryjny ƒ Número de Série ƒ Număr de serie ƒ Sériové þíslo ƒ Serijska številka ƒ
Número de serie ƒ Serienummer ƒ Raðnúmer ƒ Serienummer
Engine ƒ Ⱦɜɢɝɚɬɟɥ ƒ Motor ƒ Motor ƒ Motor ƒ Mootor ƒ Moottori ƒ Moteur ƒ Motor ƒ ȂȘȤĮȞȒ ƒ Modulnév ƒ Motore ƒ DzinƝjs ƒ Variklis ƒ Saƫƫa Netta Installata ƒ Silnik ƒ Motor ƒ Motor
ƒ Motor ƒ Motor ƒ Motor ƒ Motor ƒ Vél ƒ Motor
Ransomes Parkway 2130
Ride on Reel Mower
WB000301 - WB000310
Kubota D1505-E2B-RAN.UK-2
Net Installed Power ƒ ɇɟɬɧɚ ɢɧɫɬɚɥɢɪɚɧɚ ɦɨɳɧɨɫɬ ƒ ýistý instalovaný výkon ƒ Installeret nettoeffekt ƒ Netto geïnstalleerd vermogen ƒ Installeeritud netovõimsus ƒ Asennettu
nettoteho ƒ Puissance nominale nette ƒ Installierte Nettoleistung ƒ ȀĮșĮȡȒ İȖțĮIJİıIJȘȝȑȞȘ ȚıȤȪȢ ƒ Nettó beépített teljesítmény ƒ Potenza netta installata ƒ ParedzƝtƗ tƯkla jauda ƒ
Grynoji galia ƒ Wisa’ tal-Qtugƫ ƒ Moc zainstalowana netto ƒ Potência instalada ƒ Puterea instalată netă ƒ ýistý inštalovaný výkon ƒ Neto vgrajena moþ ƒ Potencia instalada neta ƒ
Nettoeffekt ƒ Nettóafl vélar ƒ Netto installert kraft
28 kW @ 3000 RPM
Cutting Width ƒ ɒɢɪɨɱɢɧɚ ɧɚ ɪɹɡɚɧɟ ƒ ŠíĜka Ĝezu ƒ Skærebredde ƒ Maaibreedte ƒ Lõikelaius ƒ Leikkuuleveys ƒ Largeur de coupe ƒ Schnittbreite ƒ ȂȒțȠȢ ȝȚıȚȞȑȗĮȢ ƒ Vágási
szélesség ƒ Larghezza di taglio ƒ Griešanas platums ƒ Pjovimo plotis ƒ Tikkonforma mad-Direttivi ƒ SzerokoĞü ciĊcia ƒ Largura de Corte ƒ LăĠimea de tăiere ƒ Šírka záberu ƒ Širina
reza ƒ Anchura de corte ƒ Klippbredd ƒ Skurðbreidd ƒ Klippebredde
214cm
Conforms to Directives ƒ ȼ ɫɴɨɬɜɟɬɫɬɜɢɟ ɫ ɞɢɪɟɤɬɢɜɢɬɟ ƒ SplĖuje podmínky smČrnic ƒ Er i overensstemmelse med direktiver ƒ Voldoet aan de richtlijnen ƒ Vastab direktiividele ƒ
Direktiivien mukainen ƒ Conforme aux directives ƒ Entspricht Richtlinien ƒ ǹțȠȜȠȣșȒıIJİ ʌȚıIJȐ IJȚȢ ȅįȘȖȓİȢ ƒ Megfelel az irányelveknek ƒ Conforme alle Direttive ƒ Atbilst
direktƯvƗm ƒ Atitinka direktyvǐ reikalavimus ƒ Valutazzjoni tal-Konformità ƒ Dyrektywy związane ƒ Cumpre as Directivas ƒ Respectă Directivele ƒ Je v súlade so smernicami ƒ
Skladnost z direktivami ƒ Cumple con las Directivas ƒ Uppfyller direktiv ƒ Samræmist tilskipunum ƒ I samsvar med direktiv
2006/42/EC
2004/108/EC
2000/14/EC Annex VI . Part 1
Conformity Assessment ƒ Ɉɰɟɧɤɚ ɡɚ ɫɴɨɬɜɟɬɫɬɜɢɟ ƒ Hodnocení plnČní podmínek ƒ Overensstemmelsesvurdering ƒ
Conformiteitsbeoordeling ƒ Vastavushindamine ƒ Vaatimustenmukaisuuden arviointi ƒ Evaluation de conformité ƒ
Konformitätsbeurteilung ƒ ǻȚĮʌȓıIJȦıȘ ȈȣȝȝȩȡijȦıȘȢ ƒ MegfelelĘség-értékelés ƒ Valutazione della conformità ƒ
AtbilstƯbas novƝrtƝjums ƒ Atitikties Ƴvertinimas ƒ Livell tal-Qawwa tal-ƪoss Imkejjel ƒ Ocena zgodnoĞci ƒ
Avaliação de Conformidade ƒ Evaluarea conformităĠii ƒ Vyhodnotenie zhodnosti ƒ Ocena skladnosti ƒ
Evaluación de conformidad ƒ Bedömning av överensstämmelse ƒ Samræmismat ƒ Konformitetsvurdering
2006/42/EC Annex VIII
Measured Sound Power Level ƒ ɂɡɦɟɪɟɧɨ ɧɢɜɨ ɧɚ ɡɜɭɤɨɜɚ ɦɨɳɧɨɫɬ ƒ NamČĜený akustický výkon ƒ Målte lydstyrkeniveau ƒ Gemeten geluidsniveau ƒ Mõõdetud helivõimsuse
tase ƒ Mitattu äänitehotaso ƒ Niveau de puissance sonore mesuré ƒ Gemessener Schalldruckpegel ƒ ȈIJĮșȝȚıȝȑȞȠ İʌȓʌİįȠ ȘȤȘIJȚțȒȢ ȚıȤȪȠȢ ƒ Mért hangteljesítményszint ƒ Livello
di potenza sonora misurato ƒ IzmƝrƯtais skaƼas jaudas lƯmenis ƒ Išmatuotas garso stiprumo lygis ƒ Livell tal-Qawwa tal-ƪoss Iggarantit ƒ Moc akustyczna mierzona ƒ Nível sonoro
medido ƒ Nivelul măsurat al puterii acustice ƒ Nameraná hladina akustického výkonu ƒ Izmerjena raven zvoþne moþi ƒ Nivel de potencia sonora medido ƒ Uppmätt ljudeffektsnivå
ƒ Mælt hljóðaflsstig ƒ Målt lydeffektnivå
101 dB(A) LWA
Guaranteed Sound Power Level ƒ Ƚɚɪɚɧɬɢɪɚɧɨ ɧɢɜɨ ɧɚ ɡɜɭɤɨɜɚ ɦɨɳɧɨɫɬ ƒ Garantovaný akustický výkon ƒ Garanteret lydstyrkeniveau ƒ Gegarandeerd geluidsniveau ƒ
Garanteeritud helivõimsuse tase ƒ Taattu äänitehotaso ƒ Niveau de puissance sonore garanti ƒ Garantierter Schalldruckpegel ƒ ǼȖȖȣȘȝȑȞȠ İʌȓʌİįȠ ȘȤȘIJȚțȒȢ ȚıȤȪȠȢ ƒ Szavatolt
hangteljesítményszint ƒ Livello di potenza sonora garantito ƒ GarantƝtais skaƼas jaudas lƯmenis ƒ Garantuotas garso stiprumo lygis ƒ Livell tal-Qawwa tal-ƪoss Iggarantit ƒ Moc
akustyczna gwarantowana ƒ Nível sonoro farantido ƒ Nivelul garantat al puterii acustice ƒ Garantovaná hladina akustického výkonu ƒ Zajamþena raven zvoþne moþi ƒ Nivel de
potencia sonora garantizado ƒ Garanterad ljudeffektsnivå ƒ Hljóðaflsstig sem ábyrgð er tekin á ƒ Garanter lydeffektnivå
105 dB(A) LWA
Conformity Assessment Procedure (Noise) ƒ Ɉɰɟɧɤɚ ɡɚ ɫɴɨɬɜɟɬɫɬɜɢɟ ɧɚ ɩɪɨɰɟɞɭɪɚɬɚ (ɒɭɦ) ƒ
Postup hodnocení plnČní podmínek (hluk) ƒ Procedure for overensstemmelsesvurdering (Støj) ƒ
Procedure van de conformiteitsbeoordeling (geluid) ƒ Vastavushindamismenetlus (müra) ƒ
Vaatimustenmukaisuuden arviointimenettely (Melu) ƒ Procédure d’évaluation de conformité (bruit) ƒ
Konformitätsbeurteilungsverfahren (Geräusch) ƒ ǻȚĮįȚțĮıȓĮ ǹȟȚȠȜȩȖȘıȘȢ ȈȣȝȝȩȡijȦıȘȢ (ĬȩȡȣȕȠȢ) ƒ
MegfelelĘség-értékelési eljárás (Zaj) ƒ Procedura di valutazione della conformità (rumore) ƒ
AtbilstƯbas novƝrtƝjuma procednjra (troksnis) ƒ Atitikties Ƴvertinimo procednjra (garsas) ƒ
Proƛedura tal-Valutazzjoni tal-Konformità (ƪoss) ƒ Procedura oceny zgodnoĞci (poziom haãasu) ƒ
Processo de avaliação de conformidade (nível sonoro) Procedura de evaluare a conformităĠii (zgomot) ƒ
Postup vyhodnocovania zhodnosti (hluk) ƒ Postopek za ugotavljanje skladnosti (hrup) ƒ
Procedimiento de evaluación de conformidad (ruido) ƒ Procedur för bedömning av överensstämmelse (buller)
ƒ Samræmismatsaðferð (hávaði) ƒ Prosedyre for konformitetsvurdering (støy)
UK Notified Body for 2000/14/EC ƒ ɇɨɬɢɮɢɰɢɪɚɧ ɨɪɝɚɧ ɜ Ɉɛɟɞɢɧɟɧɨɬɨ ɤɪɚɥɫɬɜɨ ɡɚ 2000/14/ȿɈ ƒ ÚĜad certifikovaný podle smČrnice þ. 2000/14/EC ƒ Det britiske
bemyndigede organ for 2001/14/EF ƒ Engels adviesorgaan voor 2000/14/EG ƒ Ühendkuningriigi teavitatud asutus direktiivi 2000/14/EÜ mõistes ƒ Direktiivin 2000/14/EY
mukainen ilmoitettu tarkastuslaitos Isossa-Britanniassa ƒ Organisme notifié concernant la directive 2000/14/CE ƒ Britische benannte Stelle für 2000/14/EG ƒ ȀȠȚȞȠʌȠȚȘȝȑȞȠȢ
ȅȡȖĮȞȚıȝȩȢ ǾȞȦȝȑȞȠȣ ǺĮıȚȜİȓȠȣ ȖȚĮ 2000/14/ǼȀ ƒ 2000/14/EK – egyesült királyságbeli bejelentett szervezet ƒ Organismo Notificato in GB per 2000/14/CE ƒ 2000/14/EK AK
reƧistrƝtƗ organizƗcija ƒ JK notifikuotosios Ƴstaigos 2000/14/EC ƒ Korp Notifikat tar-Renju Unit gƫal 2000/14/KE ƒ Dopuszczona jednostka badawcza w Wielkiej Brytanii wg
2000/14/WE ƒ Entidade notificada no Reino Unido para 2000/14/CE ƒ Organism notificat în Marea Britanie pentru 2000/14/CE ƒ Notifikovaný orgán Spojeného kráĐovstva pre
smernicu 2000/14/ES ƒ Britanski priglašeni organ za 2000/14/ES ƒ Cuerpo notificado en el Reino Unido para 2000/14/CE ƒ Anmält organ för 2000/14/EG i Storbritannien ƒ
Tilkynntur aðili í Bretlandi fyrir 2000/14/EC ƒ Britisk teknisk for 2000/14/EF
en-12
2000/14/EC Annex VI Part 1
Number: 1088
Sound Research Laboratories Limited
Holbrook House, Little Waldingfield
Sudbury, Suffolk CO10 0TH
4
SPECIFICATIONS
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
Operator Ear Noise Level ƒ Ɉɩɟɪɚɬɨɪ ɧɚ ɧɢɜɨɬɨ ɧɚ ɞɨɥɨɜɢɦ ɨɬ ɭɯɨɬɨ ɲɭɦ ƒ
Hladina hluku v oblasti uší operátora ƒ Støjniveau i førers ørehøjde ƒ
Geluidsniveau oor bestuurder ƒ Müratase operaatori kõrvas ƒ
Melutaso käyttäjän korvan kohdalla ƒ Niveau de bruit à hauteur des oreilles de l’opérateur ƒ
Schallpegel am Bedienerohr ƒ ǼʌȓʌİįȠ șȠȡȪȕȠȣ ıİ ȜİȚIJȠȣȡȖȓĮ ƒ
A kezelĘ fülénél mért zajszint ƒ Livello di potenza sonora all’orecchio dell’operatore ƒ
TrokšƼa lƯmenis pie operatora auss ƒ Dirbanþiojo su mašina patiriamo triukšmo lygis ƒ
Livell tal-ƪoss fil-Widna tal-Operatur ƒ Dopuszczalny poziom haãasu dla operatora ƒ
Nível sonoro nos ouvidos do operador ƒ Nivelul zgomotului la urechea operatorului ƒ
Hladina hluku pôsobiaca na sluch operátora ƒ Raven hrupa pri ušesu upravljavca ƒ
Nivel sonoro en el oído del operador ƒ Ljudnivå vid förarens öra ƒ Hávaðastig fyrir stjórnanda ƒ Støynivå ved operatørens øre
85.3 dB(A) Leq (2006/42/EC)
Harmonised standards used ƒ ɂɡɩɨɥɡɜɚɧɢ ɯɚɪɦɨɧɢɡɢɪɚɧɢ ɫɬɚɧɞɚɪɬɢ ƒ Použité harmonizované normy ƒ Brugte harmoniserede standarder ƒ Gebruikte geharmoniseerde
standaards ƒ Kasutatud ühtlustatud standardid ƒ Käytetyt yhdenmukaistetut standardit ƒ Normes harmonisées utilisées ƒ Angewandte harmonisierte Normen ƒ ǼȞĮȡȝȠȞȚıȝȑȞĮ
ʌȡȩIJȣʌĮ ʌȠȣ ȤȡȘıȚȝȠʌȠȚȒșȘțĮȞ ƒ Harmonizált szabványok ƒ Standard armonizzati applicati ƒ Izmantotie saskaƼotie standarti ƒ Panaudoti suderinti standartai ƒ Standards
armonizzati uĪati ƒ Normy spójne powiązane ƒ Normas harmonizadas usadas ƒ Standardele armonizate utilizate ƒ Použité harmonizované normy ƒ Uporabljeni usklajeni standardi
ƒ Estándares armonizados utilizados ƒ Harmoniserade standarder som används
BS EN 1032:2003+A1:2008
BS EN ISO 20643:2008
BS EN ISO 5349-1:2001
BS EN ISO 5349-2:2002
BS EN ISO 14982:1998
BS EN 50338:2006
BS EN 60335-2-77:2006
BS EN 1032:2003
BS EN 836-1997
Technical standards and specifications used ƒ ɂɡɩɨɥɡɜɚɧɢ ɬɟɯɧɢɱɟɫɤɢ ɫɬɚɧɞɚɪɬɢ ɢ ɫɩɟɰɢɮɢɤɚɰɢɢ ƒ
Použité technické normy a specifikace ƒ Brugte tekniske standarder og specifikationer ƒ
Gebruikte technische standaards en specificaties ƒ Kasutatud tehnilised standardid ja spetsifikatsioonid ƒ
Käytetyt tekniset standardit ja eritelmät ƒ Spécifications et normes techniques utilisées ƒ
Angewandte technische Normen und Spezifikationen ƒ ȉİȤȞȚțȐ ʌȡȩIJȣʌĮ țĮȚ ʌȡȠįȚĮȖȡĮijȑȢ ʌȠȣ ȤȡȘıȚȝȠʌȠȚȒșȘțĮȞ ƒ MĦszaki szabványok és specifikációk ƒ Standard tecnici e
specifiche applicati ƒ
Izmantotie tehniskie standarti un specifikƗcijas ƒ Panaudoti techniniai standartai ir techninơ informacija ƒ
Standards u speƛifikazzjonijiet tekniƛi uĪati ƒ Normy i specyfikacje techniczne powiązane ƒ
Normas técnicas e especificações usadas ƒ Standardele tehnice úi specificaĠiile utilizate ƒ
Použité technické normy a špecifikácie ƒ Uporabljeni tehniþni standardi in specifikacije ƒ
Estándares y especificaciones técnicas utilizadas ƒ Tekniska standarder och specifikationer som används ƒ Samræmdir staðlar sem notaðir eru ƒ Benyttede harmoniserte
standarder
OECD Code 4 ROPS static Test
BS ISO 2631-1 AMD1
The place and date of the declaration ƒ Ɇɹɫɬɨ ɢ ɞɚɬɚ ɧɚ ɞɟɤɥɚɪɚɰɢɹɬɚ ƒ Místo a datum prohlášení ƒ Sted og dato for erklæringen ƒ Plaats en datum van de verklaring ƒ
Deklaratsiooni väljastamise koht ja kuupäev ƒ Vakuutuksen paikka ja päivämäärä ƒ Lieu et date de la déclaration ƒ Ort und Datum der Erklärung ƒ ȉȩʌȠȢ țĮȚ ȘȝİȡȠȝȘȞȓĮ
įȒȜȦıȘȢ ƒ A nyilatkozat kelte (hely és idĘ) ƒ Luogo e data della dichiarazione ƒ DeklarƗcijas vieta un datums ƒ Deklaracijos vieta ir data ƒ Il-post u d-data tad-dikjarazzjoni ƒ
Miejsce i data wystawienia deklaracji ƒ Local e data da declaração ƒ Locul úi data declaraĠiei ƒ Miesto a dátum vyhlásenia ƒ Kraj in datum izjave ƒ Lugar y fecha de la declaración
ƒ Plats och datum för deklarationen ƒ Tæknistaðlar og tæknilýsingar sem notaðar eru ƒ Benyttede tekniske standarder og spesifikasjoner ƒ Staður og dagsetning yfirlýsingar ƒ
Sted og dato for erklæringen
Ransomes Jacobsen Limited
West Road, Ransomes Europark,
Ipswich, England, IP3 9TT
4th January 2010
Signature of the person empowered to draw up the declaration on behalf of the manufacturer, holds the technical documentation and is authorised to compile the technical file, and who is
established in the Community.
ɉɨɞɩɢɫ ɧɚ ɱɨɜɟɤɚ, ɭɩɴɥɧɨɦɨɳɟɧ ɞɚ ɫɴɫɬɚɜɢ ɞɟɤɥɚɪɚɰɢɹɬɚ ɨɬ ɢɦɟɬɨ ɧɚ ɩɪɨɢɡɜɨɞɢɬɟɥɹ, ɤɨɣɬɨ ɩɨɞɞɴɪɠɚɳ
ɬɟɯɧɢɱɟɫɤɚɬɚ ɞɨɤɭɦɟɧɬɚɰɢɹ ɢ ɟ ɨɬɨɪɢɡɢɪɚɧ ɞɚ ɢɡɝɨɬɜɢ ɬɟɯɧɢɱɟɫɤɢɹ ɮɚɣɥ ɢ ɟ ɪɟɝɢɫɬɪɢɪɚɧ ɜ ɨɛɳɧɨɫɬɬɚ.
Podpis osoby oprávnČné sestavit prohlášení jménem výrobce, držet technickou dokumentaci a osoby oprávnČné
sestavit technické soubory a založené v rámci Evropského spoleþenství.
Underskrift af personen, der har fuldmagt til at udarbejde erklæringen på vegne af producenten, der er indehaver
af dokumentationen og er bemyndiget til at udarbejde den tekniske journal, og som er baseret i nærområdet.
Handtekening van de persoon die bevoegd is de verklaring namens de fabrikant te tekenen, de technische
documentatie bewaart en bevoegd is om het technische bestand samen te stellen, en die is gevestigd in het Woongebied.
Ühenduse registrisse kantud isiku allkiri, kes on volitatud tootja nimel deklaratsiooni koostama, kes omab tehnilist
dokumentatsiooni ja kellel on õigus koostada tehniline toimik.
Sen henkilön allekirjoitus, jolla on valmistajan valtuutus vakuutuksen laadintaan, jolla on hallussaan tekniset
asiakirjat, joka on valtuutettu laatimaan tekniset asiakirjat ja joka on sijoittautunut yhteisöön.
Signature de la personne habilitée à rédiger la déclaration au nom du fabricant, à détenir la documentation
technique, à compiler les fichiers techniques et qui est implantée dans la Communauté.
Unterschrift der Person, die berechtigt ist, die Erklärung im Namen des Herstellers abzugeben, die die
technischen Unterlagen aufbewahrt und berechtigt ist, die technischen Unterlagen zusammenzustellen,
und die in der Gemeinschaft niedergelassen ist.
ȊʌȠȖȡĮijȒ ĮIJȩȝȠȣ İȟȠȣıȚȠįȠIJȘȝȑȞȠȣ ȖȚĮ IJȘȞ ıȪȞIJĮȟȘ IJȘȢ įȒȜȦıȘȢ İț ȝȑȡȠȣȢ IJȠȣ țĮIJĮıțİȣĮıIJȒ, Ƞ ȠʌȠȓȠȢ
țĮIJȑȤİȚ IJȘȞ IJİȤȞȚțȒ ȑțșİıȘ țĮȚ ȑȤİȚ IJȘȞ İȟȠȣıȚȠįȩIJȘıȘ ȞĮ IJĮȟȚȞȠȝȒıİȚ IJȠȞ IJİȤȞȚțȩ ijȐțİȜȠ țĮȚ Ƞ ȠʌȠȓȠȢ İȓȞĮȚ įȚȠȡȚıȝȑȞȠȢ ıIJȘȞ ȀȠȚȞȩIJȘIJĮ.
A gyártó nevében meghatalmazott személy, akinek jogában áll módosítania a nyilatkozatot, a mĦszaki
dokumentációt Ęrzi, engedéllyel rendelkezik a mĦszaki fájl összeállításához, és aki a közösségben letelepedett személy.
Firma della persona autorizzata a redigere la dichiarazione a nome del fabbricante, in possesso Della
documentazione tecnica ed autorizzata a costituire il fascicolo tecnico, che deve essere stabilita nella Comunità.
TƗs personas paraksts, kura ir pilnvarota deklarƗcijas sastƗdƯšanai ražotƗja vƗrdƗ, kurai ir tehniskƗ
dokumentƗcija, kura ir pilnvarota sagatavot tehnisko reƧistru un kura ir apstiprinƗta KopienƗ.
Asmuo, kuris yra gana žinomas, kuriam gamintojas suteikơ Ƴgaliojimus sudaryti šią deklaraciją, ir kuris ją
pasirašơ, turi visą techninĊ informaciją ir yra Ƴgaliotas sudaryti techninơs informacijos dokumentą.
Il-firma tal-persuna awtorizzata li tfassal id-dikjarazzjoni f’isem il-fabbrikant, gƫandha d-dokumentazzjoni
teknika u hija awtorizzata li tikkompila l-fajl tekniku u li hija stabbilita fil-Komunità.
Podpis osoby upowaĪnionej do sporządzenia deklaracji w imieniu producenta, przechowującej dokumentacjĊ
techniczną, upowaĪnioną do stworzenia dokumentacji technicznej oraz wyznaczonej ds. wspólnotowych.
Assinatura da pessoa com poderes para emitir a declaração em nome do fabricante, que possui a documentação
técnica, que está autorizada a compilar o processo técnico e que está estabelecida na Comunidade.
Semnătura persoanei împuternicite să elaboreze declaraĠia în numele producătorului, care deĠine documentaĠia
tehnică, este autorizată să compileze dosarul tehnic úi este stabilită în Comunitate.
Podpis osoby poverenej vystavením vyhlásenia v mene výrobcu, ktorá má technickú dokumentáciu a je
oprávnená spracovaĢ technické podklady a ktorá je umiestnená v Spoloþenstve.
Podpis osebe, pooblašþene za izdelavo izjave v imenu proizvajalca, ki ima tehniþno dokumentacijo in lahko
sestavlja spis tehniþne dokumentacije, ter ima sedež v Skupnosti.
Firma de la persona responsable de la declaración en nombre del fabricante, que posee la documentación técnica
y está autorizada para recopilar el archivo técnico y que está establecido en la Comunidad.
Undertecknas av den som bemyndigad att upprätta deklarationen å tillverkarens vägnar, innehar den tekniska
dokumentationen och är bemyndigad att sammanställa den tekniska informationen och som är etablerad i
gemenskapen. Undirskrift aðilans sem hefur umboð til að gera yfirlýsinguna fyrir hönd framleiðandans, hefur undir höndum
tæknigögnin og hefur leyfi til að taka saman tækniskýrsluna, og er viðurkenndur innan evrópska efnahagssvæðisins.
Signaturen til personen som har fullmakt til å utferdige erklæringen på vegne av produsenten, er i besittelse av den
tekniske dokumentasjonen, har autorisasjon til å utarbeide den tekniske filen og som har tilhold i EU.
Tim Lansdell
Technical Director
4th January 2010
Ransomes Jacobsen Limited
West Road, Ransomes Europark,
Ipswich, England, IP3 9TT
Certificate Number ƒ ɇɨɦɟɪ ɧɚ ɫɟɪɬɢɮɢɤɚɬ ƒ ýíslo osvČdþení ƒ Certifikatnummer ƒ Certificaatnummer ƒ Sertifikaadi number ƒ Hyväksyntänumero ƒ Numéro de certificat ƒ
Bescheinigungsnummer ƒ ǹȡȚșȝȩȢ ȆȚıIJȠʌȠȚȘIJȚțȠȪ ƒ Hitelesítési szám ƒ Numero del certificato ƒ SertifikƗta numurs ƒ Sertifikato numeris ƒ Numru taƛ-ƚertifikat ƒ Numer
certyfikatu ƒ Número do Certificado ƒ Număr certificat ƒ ýíslo osvedþenia ƒ Številka certifikata ƒ Número de certificado ƒ Certifikatsnummer ƒ Númer skírteinis ƒ Sertifikatnummer
4117927-r4
en-13
4
SPECIFICATIONS
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
DECLARATION OF INCORPORATION ƒ ȾȿɄɅȺɊȺɐɂə ɁȺ ɈȻȿȾɂɇȿɇɂȿ ƒ PROHLÁŠENÍ O ZALOŽENÍ SPOLEýNOSTI ƒ INKORPORERINGSERKLÆRING ƒ
INCORPORATIEVERKLARING ƒ KINNITUS ÜHENDAMISE KOHTA ƒ ASENNUSTODISTUS ƒ DECLARATION D’INCORPORATION ƒ EINBAUBESCHEINIGUNG ƒ ǻǾȁȍȈǾ ȂǾ
ȈȊȂȂȅȇĭȍȈǾȈ ƒ BEÉPÍTÉSI NYILATKOZAT ƒ DICHIARAZIONE DI INCORPORAZIONE ƒ NOFORMƜŠANAS DEKLARƖCIJA ƒ PRIJUNGIMO DEKLARACIJA ƒ DIKJARAZZJONI TA’
INKORPORAZZJONI ƒ DEKLARACJA ZGODNOĝCI DLA PODZESPOâU ƒ DECLARAÇÃO DE INCORPORAÇÃO ƒ DECLARAğIE DE ÎNCORPORARE ƒ VYHLÁSENIE O
ZABUDOVANÍ SÚýASTI ƒ IZJAVA ZA VGRADNJO ƒ DECLARACIÓN DE INCORPORACIÓN ƒ INBYGGNADSDEKLARATION ƒ YFIRLÝSING UM ÍSETNINGU ƒ PRODUSENTENS
ERKLÆRING
Business name and full address of the manufacturer ƒ Ɍɴɪɝɨɜɫɤɨ ɢɦɟ ɢ ɩɴɥɟɧ ɚɞɪɟɫ ɧɚ ɩɪɨɢɡɜɨɞɢɬɟɥɹ ƒ Obchodní jméno a plná adresa výrobce ƒ Producentens firmanavn og fulde adresse ƒ Bedrijfsnaam
en volledig adres van de fabrikant ƒ Tootja ärinimi ja täielik aadress ƒ Valmistajan toiminimi ja täydellinen osoite ƒ Nom commercial et adresse complète du fabricant ƒ Firmenname und vollständige Adresse
des Herstellers ƒ ǼʌȦȞȣȝȓĮ țĮȚ IJĮȤȣįȡȠȝȚțȒ įȚİȪșȣȞıȘ țĮIJĮıțİȣĮıIJȒ ƒ A gyártó üzleti neve és teljes címe ƒ Ragione sociale e indirizzo completo del fabbricante ƒ UzƼƝmuma nosaukums un pilna ražotƗja
adrese ƒ Verslo pavadinimas ir pilnas gamintojo adresas ƒ Isem kummerƛjali u indirizz sƫiƫ tal-fabbrikant ƒ Nazwa firmy i peãny adres producenta ƒ Nome da empresa e endereço completo do fabricante ƒ
Denumirea comercială úi adresa completă a producătorului ƒ Obchodný názov a úplná adresa výrobcu ƒ Naziv podjetja in polni naslov proizvajalca ƒ Nombre de la empresa y dirección completa del fabricante
ƒ Tillverkarens företagsnamn och kompletta adress ƒ Fyrirtækisheiti og fullt heimilisfang framleiðanda. ƒ Firmanavn og full adresse for produsenten.
Ransomes Jacobsen Limited
West Road, Ransomes Europark,
Ipswich, England, IP3 9TT
Description and identification of the partly completed machinery. ƒ Ɉɩɢɫɚɧɢɟ ɢ ɢɞɟɧɬɢɮɢɤɚɰɢɹ ɧɚ ɱɚɫɬɢɱɧɨ ɡɚɜɴɪɲɟɧɢɬɟ ɦɚɲɢɧɢ. ƒ Popis a identifikace þásteþnČ dokonþeného strojního zaĜízení.
ƒ Beskrivelse og identifikation af den delvist fremstillede maskine. ƒ Beschrijving en identificatie van de gedeeltelijk voltooide machinerie. ƒ Osaliselt komplekteeritud masina kirjeldus ja määratlus.
ƒ Osittain kootun laitteiston kuvaus ja määrittely. ƒ Description et identification de la quasi-machine. ƒ Bezeichnung und Identifizierung der teilgefertigten Vorrichtung ƒ ȆİȡȚȖȡĮijȒ țĮȚ ʌȡȠıįȚȠȡȚıȝȩȢ
ȘȝȚIJİȜȠȪȢ ȝȘȤĮȞȒȝĮIJȠȢ. ƒ A részlegesen megépített gép leírása és meghatározása. ƒ Descrizione e identificazione della quasi-macchina ƒ DaƺƝji pabeigtas iekƗrtas apraksts un identifikƗcija. ƒ Dalinai užbaigtos Ƴrangos
aprašymas ir identifikacija. ƒ Deskrizzjoni u identifikazzjoni tal-makkinarju li jkun lest parzjalment. ƒ Opis i oznaczenie czĊĞciowo ukoĔczonego urządzenia ƒ Descrição e identificação do equipamento parcial ƒ
Descrierea úi identificarea echipamentului finalizat parĠial ƒ Opis a identifikácia podzostavy strojného zariadenia ƒ Opis in identifikacija delno dokonþanega stroja. ƒ Descripción e identificación de la maquinaria
parcialmente completada. ƒ Beskrivning och identifiering av maskindelarna. ƒ Fyrirtækisheiti og fullt heimilisfang framleiðanda. ƒ Lýsing og auðkenni hálfsamsetta vélbúnaðarins. ƒ Erklæring og identifikasjon for det delvis ferdigstilte maskineriet.
Product Code
LMAB352
Serial Number
UK000301 - UK999999
Description
Sport 200,8 knife,LH, floating head
LMAB353
UW000301 - UW999999
Sport 200 8 knife,RH,floating head
LMAB445
XT000301 - XT999999
Sport 200 11 knife floating head units LH handwheel both adjustments- standard roll
LMAB446
XU000301 - XU099999
Sport 200 11 knife floating head unit RH handwheel both adjustments- standard roll
LMAB556
XM000301 - XM999999
Magna 250 6 knife fixed head units LH spanner adjust both adjustments - disposible. Roll
LMAB558
XN000301 - XN999999
Magna 250 6 knife RH fixed head - disposible. Roll
LMAB559
XR000301 - XR999999
Magna 250 6 knife fixed head units RH spanner H of C, hand on cut - disposible. Roll
LMAB560
XS000301 - XS999999
Magna 250 6 knife fixed head units LH spanner H of C, hand on cut - disposible. Roll
LMAB561
XD000301 - XD999999
Magna 250 4 knife fixed head units LH spanner adjust both adjustments - disposible. Roll
LMAB562
XE000301 - XE999999
Magna 2504 knife fixed head units RH spanner adjust bith adjustments - disposible. Roll
LMAB564
XH000301 - XH999999
Magna 250 4 knife fixed head units RH spanner H of C, hand on cut - disposible. Roll
LMAB565
XJ000301 - XJ999999
Magna 250 4 knife fixed head units LH spanner H of C, hand on cut - disposible. Roll
LMAB585
XB000301 - XB999999
Magna 250 4 knife fixed head units LH spanner adjust both adjustments - standard roll
LMAB586
XC000301 - XC999999
Magna 250 4 knife RH fixed - standard roll
LMAB587
XF000301 - XF999999
Magna 250 4 knife fixed head units RH spanner H of C, hand on cut - standard roll
LMAB588
XG000301 - XG999999
Magna 250 4 knife fixed head units LH spanner H of C, hand on cut - standard roll
LMAB589
XK000301 - XK999999
Magna 250 6 knife fixed head units LH spanner adjust both adjustments - standard roll
LMAB590
XL000301 - XL999999
Magna 250-6 knife RH fixed head - standard roll
LMAB591
XP000301 - XP999999
Magna 250 6 knife fixed head units RH spanner H of C, hand on cut - standard roll
LMAB592
XQ000301 - XQ999999
Magna 250 6 knife fixed head units LH spanner H of C, hand on cut - standard roll
LMAB594
BT000301 - BT999999
Verticut unit RH
LMAB595
BU000301 - BU999999
Verticut unit LH
We undertake to transmit, in response to a reasoned request by the national authorities, relevant information on the partly completed machinery. This shall be by hardcopy and shall be without prejudice to the intellectual property
rights of the manufacturer of the partly completed machinery.
ɇɢɟ ɨɛɟɳɚɜɚɦɟ ɞɚ ɩɪɟɞɚɞɟɦ, ɜ ɨɬɝɨɜɨɪ ɧɚ ɨɫɧɨɜɚɬɟɥɧɨ ɢɫɤɚɧɟ ɨɬ ɧɚɰɢɨɧɚɥɧɢɬɟ ɨɪɝɚɧɢ, ɫɴɨɬɜɟɬɧɚ ɢɧɮɨɪɦɚɰɢɹ ɡɚ ɱɚɫɬɢɱɧɨ ɡɚɜɴɪɲɟɧɢɬɟ ɦɚɲɢɧɢ. Ɍɨɜɚ ɳɟ ɫɟ ɨɫɴɳɟɫɬɜɢ ɱɪɟɡ ɞɨɤɭɦɟɧɬ ɢ ɧɹɦɚ ɞɚ ɛɴɞɟ ɜ ɧɚɪɭɲɟɧɢɟ
ɧɚ ɩɪɚɜɚɬɚ ɡɚ ɢɧɬɟɥɟɤɬɭɚɥɧɚ ɫɨɛɫɬɜɟɧɨɫɬ ɧɚ ɩɪɨɢɡɜɨɞɢɬɟɥɹ ɧɚ ɱɚɫɬɢɱɧɨ ɡɚɜɴɪɲɟɧɢɬɟ ɦɚɲɢɧɢ.
Zavazujeme se na základČ zdĤvodnČné žádosti ze strany národních úĜadĤ poskytnout pĜíslušné informace o þásteþnČ dokonþeném strojním zaĜízení. Informace budou pĜedány v tištČné podobČ a
nepoškodí práva k duševnímu vlastnictví výrobce týkající se þásteþnČ dokonþeného strojního zaĜízení.
Som svar på en begrundet anmodning fra de nationale myndigheder forpligter vi os til at videregive oplysninger om den delvist fremstillede maskine. Dette bliver gjort i papirudgave og med forbehold
for de immaterielle rettigheder, som indehaves af producenten af den delvist fremstillede maskine.
We zijn van plan, in reactie op een redelijk verzoek van de nationale autoriteiten, relevante informatie over de gedeeltelijk voltooide machinerie te verzenden. Dit wordt gedaan in de vorm van fysieke
kopieën en deze kopieën zullen onder alle voorbehoud behoren tot de intellectuele eigendomsrechten van de fabrikant van de gedeeltelijk voltooide machinerie.
Me kohustume riigisiseste asutuste põhjendatud nõudmisel edastama asjakohast teavet osaliselt komplekteeritud masina kohta. Andmed edastatakse paberkandjal ning sellega ei tohi piirata osaliselt komplekteeritud masina
tootja õigusi intellektuaalsele omandile.
Sitoudumme toimittamaan osittain koottua laitteistoa koskevat olennaiset tiedot vastineena kansallisten viranomaisten perusteltuun pyyntöön. Tiedot toimitetaan paperitulosteena. Ne eivät rajoita
valmistajan osittain koottua laitteistoa koskevia immateriaalioikeuksia.
Nous nous engageons à fournir, en réponse à une demande rationnelle des autorités nationales, toute information appropriée concernant la quasi-machine. Ceci se fera par copie papier et sans
préjuger des droits de propriété intellectuelle du fabricant de la quasi-machine.
Wir verpflichten uns, auf eine begründete Aufforderung durch die nationalen Behörden hin, relevante Informationen über die teilgefertigte Maschine zu übersenden. Diese werden als Ausdruck
übersandt und dürfen sich nicht nachteilig auf die Rechte am geistigen Eigentum des Herstellers der teilgefertigten Maschine auswirken.
ǹȞĮȜĮȝȕȐȞȠȣȝİ ȞĮ ȝİIJĮȕȚȕȐıȠȣȝİ, ʌȡȠȢ ĮʌȐȞIJȘıȘ İȪȜȠȖȘȢ ĮȓIJȘıȘȢ IJȦȞ İșȞȚțȫȞ ĮȡȤȫȞ, IJȚȢ ıȤİIJȚțȑȢ ʌȜȘȡȠijȠȡȓİȢ ȩıȠȞ ĮijȠȡȐ IJȠ ȘȝȚIJİȜȑȢ ȝȘȤȐȞȘȝĮ. ǹȣIJȩ șĮ ʌȡȑʌİȚ ȞĮ ȖȓȞİȚ ȖȡĮʌIJȫȢ țĮȚ įȓȤȦȢ ȞĮ
șȓȖİȚ IJĮ ʌȞİȣȝĮIJȚțȐ įȚțĮȚȫȝĮIJĮ IJȠȣ țĮIJĮıțİȣĮıIJȒ IJȠȣ ȘȝȚIJİȜȠȪȢ ȝȘȤĮȞȒȝĮIJȠȢ.
Vállaljuk, hogy átadjuk – a nemzeti hatóságok megalapozott kérésére válaszul – a részlegesen megépített gépre vonatkozó információkat. Az információkat nyomtatott példányban adjuk át. A
nyomtatott példány átadása a részlegesen megépített gép gyártójának szellemi tulajdonjogaira tett kötelezettség nélkül történik.
Ci impegniamo a trasmettere, in risposta ad una richiesta adeguatamente motivata delle autorità nazionali, informazioni pertinenti sulla quasi-macchina. L’impegno sarà redatto in forma cartacea e
lascerà impregiudicati i diritti di proprietà intellettuale del fabbricante della quasi-macchina.
Atsaucoties uz pamatotu valsts iestƗžu pieprasƯjumu, mƝs apƼemamies nodot saistƯto informƗciju par daƺƝji pabeigtu iekƗrtu. TƗ bnjs cietƗ kopija un neradƯs kaitƝjumus daƺƝji pabeigtƗs iekƗrtas ražotƗja intelektuƗlƗ Ưpašuma
tiesƯbƗm.
Atsakydami Ƴ nacionaliniǐ valdžios organǐ užklausą, pateikiame informaciją apie dalinai užbaigtus mechanizmus. Šis dokumentas yra atspausdintas elektroninio originalo variantas ir be jokio
išankstinio nusistatymo neturi tikslo pažeisti dalinai užbaigto mechanizmo gamintojo intelektualinơs nuosavybơs teisiǐ.
Aƫna nwiegƫdu li nippreĪentaw, meta mitlubin mill-awtoritajiet nazzjonali, l-informazzjoni relevanti dwar il-makkinarju li jkun lest parzjalment. Din l-informazzjoni gƫandha tkun f’forma stampata u
mingƫajr preƥudizzju gƫad-drittijiet tal-proprjetà intelletwali tal-fabbrikant tal-makkinarju li jkun lest parzjalment.
Na uzasadnioną proĞbĊ instytucji paĔstwowych zobowiązujemy siĊ do przekazania wszelkich informacji na temat czĊĞciowo ukoĔczonego urządzenia. BĊdą one przekazane na piĞmie. Strona
przekazująca w/wym. dokumentacjĊ nie bĊdzie roĞciãa sobie Īadnych praw do wãasnoĞci intelektualnej producenta czĊĞciowo ukoĔczonego urządzenia.
Na sequência de pedido razoável por parte das autoridades nacionais, comprometemo-nos a transmitir informações importantes sobre o equipamento parcial. Tal será feito por meio de hardcopy
e sem prejuízo para os direitos de propriedade intelectual do fabricante do equipamento parcial.
Ne angajăm să transmitem, ca răspuns la o solicitare motivată a autorităĠilor naĠionale, informaĠii relevante privind echipamentul finalizat parĠial. Aceasta se va efectua în format hârtie úi fără a aduce
atingere drepturilor de proprietate intelectuală ale producătorului echipamentului finalizat parĠial.
Zaväzujeme sa, že na základe odôvodnenej požiadavky národných orgánov predložíme dôležité informácie o podzostave strojného zariadenia.
Musí to byĢ v tlaþenej forme a bez ujmy na právach duševného vlastníctva výrobcu podzostavy strojného zariadenia.
Zavezujemo se, da bomo na utemeljeno zahtevo nacionalnih organov predložili zadevne informacije o delno dokonþanem stroju. Informacije bodo v tiskani obliki in ne bodo posegale v pravice
intelektualne lastnine proizvajalca delno dokonþanega stroja.
Nos comprometemos a transmitir, en respuesta a una petición razonada por parte de las autoridades nacionales, información relevante sobre la maquinaria parcialmente completada. Ésta será
transmitida en copia impresa y no afectará a los derechos de propiedad intelectual del fabricante de la maquinaria parcialmente completada.
Vi åtar oss att vidarebefordra relevant information om maskindelarna vid en motiverad förfrågan från nationella myndigheter. Informationen ska erhållas i form av papperskopior och ska vara utan men
för maskindelstillverkarens immateriella rättigheter.
Berist okkur rökstudd beiðni frá landsyfirvöldum um að senda mikilvægar upplýsingar um hálfsamsetta vélbúnaðinn, munum við verða við slíkri beiðni. Beiðnin skal vera í prentriti og gilda með fyrirvara um hugverkarétt
framleiðanda hálfsamsetta vélbúnaðarins.
Vi vil, på anmodning fra nasjonale myndigheter, formidle all relevant informasjon om det delvis ferdigstilte maskineriet. Informasjonen vil bli formidlet i papirutgave og skal være uten prejudise for åndsrettighetene til produsenten
av det delvis ferdigstilte maskineriet.
en-14
4
SPECIFICATIONS
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
Partly completed machinery must not be put into service until the final machinery into which it is to be incorporated has been declared in conformity with the provisions of Directive
2006/42/EC.
ɑɚɫɬɢɱɧɨ ɡɚɜɴɪɲɟɧɢɬɟ ɦɚɲɢɧɢ ɧɟ ɬɪɹɛɜɚ ɞɚ ɛɴɞɚɬ ɩɭɫɤɚɧɚ ɜ ɭɩɨɬɪɟɛɚ, ɞɨɤɚɬɨ ɤɪɚɣɧɢɬɟ ɦɚɲɢɧɢ, ɜ ɤɨɢɬɨ ɫɚ ɜɝɪɚɞɟɧɢ, ɧɟ ɫɚ ɩɪɢɜɟɞɟɧɢ ɜ ɫɴɨɬɜɟɬɫɬɜɢɟ ɫ ɩɨɫɬɚɧɨɜɥɟɧɢɹɬɚ ɧɚ
ɞɢɪɟɤɬɢɜɚ 2006/42/EɈ.
ýásteþnČ dokonþené zaĜízení nesmí být uvedeno do provozu, dokud koneþné zaĜízení, do kterého bylo uvedené zaĜízení namontováno, neodpovídá ustanovením SmČrnice þ.
2006/42/EC.
Delvist fremstillede maskiner må ikke indsættes i driften, før den endelige maskine, som den skal inkorporeres i, er blevet erklæret I overensstemmelse med bestemmelserne i Direktiv
2006/42/EF.
Gedeeltelijk voltooide machinerie mag niet in dienst worden genomen, totdat er voor de definitieve machinerie, waarvan gedeeltelijk voltooide machinerie onderdeel uitmaakt, een
conformiteitsverklaring is ontvangen onder de voorwaarden van Richtlijn 2006/42/EG.
Osaliselt komplekteeritud masinat ei tohi kasutusele võtta enne, kui lõplikult komplekteeritud masin, millega see ühendatakse, on tunnistatud direktiivi 2006/42/EÜ sätetele vastavaks.
Osittain koottua laitteistoa ei saa ottaa käyttöön, ennen kuin lopullinen laitteisto, johon se asennetaan, on vakuutettu direktiivin 2006/42/EY säännösten mukaiseksi.
La quasi-machine ne doit pas être mise en service avant que la machine finale dans laquelle elle doit être incorporée n’ait été déclarée conforme aux dispositions de la directive
2006/42/CE
Die teilgefertigte Vorrichtung darf erst in Betrieb genommen werden, wenn die Konformität der Maschine, in die sie eingebaut wird, entsprechend den Bestimmungen der Richtlinie
2006/42/EG erklärt worden ist.
ĬĮ ʌȡȑʌİȚ ȞĮ İțIJİȜİıIJİȓ ıȑȡȕȚȢ ıIJȠ ȘȝȚIJİȜȑȢ ȝȘȤȐȞȘȝĮ ȝȑȤȡȚ IJȠ IJİȜȚțȩ ȝȘȤȐȞȘȝĮ ıIJȠ ȠʌȠȓȠ șĮ İȞıȦȝĮIJȦșİȓ ȞĮ ȑȤİȚ IJȘ įȒȜȦıȘ ıȣȝȝȩȡijȦıȘȢ, ıȪȝijȦȞĮ ȝİ IJȚȢ įȚĮIJȐȟİȚȢ IJȘȢ ȅįȘȖȓĮȢ
2006/42/ǼȀ.
A részlegesen megépített gépet tilos üzembe helyezni mindaddig, amíg a 2006/42/EK irányelv rendelkezéseivel összhangban a részlegesen megépített gépet be nem építik a végleges
változatba, és errĘl nem nyilatkoznak.
La quasi-macchina non deve essere messa in servizio finché la macchina finale in cui deve essere incorporata non è stata dichiarata conforme, nel caso, alle disposizioni della Direttiva
2006/42/CE.
DaƺƝji pabeigtu iekƗrtu nedrƯkst nodot ekspluatƗcijƗ, lƯdz galƯgƗ iekƗrta, kurƗ tƗ ir jƗiebnjvƝ, ir deklarƝta atbilstoši direktƯvas Nr. 2006/42/EK noteikumiem.
These accessories have been designed
to be fitted to the Ransomes
Parkway 2250 Plus
LGNN040
Dalinai užbaigto mechanizmo negalima paleisti kol kiti mechanizmai, kurie dar bus prijungti, nebus patvirtinti kaip atitinkantys 2006/42/EC Direktyvos reikalavimus.
Il-makkinarju li jkun parzjalment lest ma gƫandux jibda jitƫaddem sakemm il-makkinarju finali li fih ikun se jiƥi inkorporat ikun ƥie ddikjarat konformi mad-dispoĪizzjonijiet tad-Direttiva
2006/42/KE.
Urządzenia czĊĞciowo ukoĔczonego nie wolno uĪytkowaü aĪ do orzeczenia zgodnoĞci urządzenia w postaci kompletnej z
wymaganiami dyrektywy 2006/42/WE.
O equipamento parcial não poderá entrar em funcionamento antes do mecanismo final no qual vai ser incorporado ser declarado como estando em conformidade com as condições da
Directiva 2006/42/CE.
Echipamentul finalizat parĠial nu trebuie pus în funcĠiune până ce echipamentul final în care va fi încorporat nu este declarat ca fiind conform cu prevederile Directivei 2006/42/CE.
Podzostava strojného zariadenia nesmie byĢ uvedená do prevádzky, pokiaĐ finálne strojné zariadenie, ktorého sa stane súþasĢou, nebude vyhlásené ako zhodné s ustanoveniami
smernice 2006/42/ES.
Delno dokonþanega stroja ni dovoljeno dati v obratovanje, dokler se dokonþani stroj, v katerega se vgradi delno dokonþani stroj, ne potrdi kot skladen z doloþbami Direktive 2006/42/ES.
La maquinaria parcialmente completada no debe ponerse en servicio hasta que la maquinaria final a la que debe incorporarse cumpla con las provisiones de la Directiva 2006/42/CE.
Maskindelarna får ej tas i bruk förrän maskinen som delen tillhör har deklarerats som överensstämmande med föreskrifterna I direktivet 2006/42/EG.
Hálfsamsettan vélbúnað má ekki taka í notkun fyrr en vottað hefur verið að endanlegi vélbúnaðurinn sem setja á hann í samræmist ákvæðum tilskipunar 2006/42/EC.
Delvis ferdigstilt maskineri skal ikke tas i bruk før det endelige maskineriet som dette skal integreres i, er erklært å være i overensstemmelse med bestemmelsene i direktiv 2006/42/EF.
The place and date of the declaration ƒ Ɇɹɫɬɨ ɢ ɞɚɬɚ ɧɚ ɞɟɤɥɚɪɚɰɢɹɬɚ ƒ
Místo a datum prohlášení ƒ Sted og dato for erklæringen ƒ
Plaats en datum van de verklaring ƒ Deklaratsiooni väljastamise koht ja kuupäev ƒ
Vakuutuksen paikka ja päivämäärä ƒ Lieu et date de la déclaration ƒ
Ort und Datum der Erklärung ƒ ȉȩʌȠȢ țĮȚ ȘȝİȡȠȝȘȞȓĮ įȒȜȦıȘȢ ƒ
A nyilatkozat kelte (hely és idĘ) ƒ Luogo e data della dichiarazione ƒ
DeklarƗcijas vieta un datums ƒ Deklaracijos vieta ir data ƒ
Il-post u d-data tad-dikjarazzjoni ƒ Miejsce i data wydania deklaracji ƒ
Local e data da declaração ƒ Locul úi data declaraĠiei ƒ
Miesto a dátum vyhlásenia ƒ Slovenian ƒ
Lugar y fecha de la declaración ƒ Plats och datum för deklarationen ƒ
Staður og dagsetning yfirlýsingar ƒ Sted og dato for erklæringen
Ransomes Jacobsen Limited
West Road, Ransomes Europark,
Ipswich, England, IP3 9TT
4th January 2010
Signature of the person empowered to draw up the declaration on behalf of the manufacturer, holds the technical documentation and is authorised
to compile the technical file, and who is established in the Community.
ɉɨɞɩɢɫ ɧɚ ɱɨɜɟɤɚ, ɭɩɴɥɧɨɦɨɳɟɧ ɞɚ ɫɴɫɬɚɜɢ ɞɟɤɥɚɪɚɰɢɹɬɚ ɨɬ ɢɦɟɬɨ ɧɚ ɩɪɨɢɡɜɨɞɢɬɟɥɹ, ɤɨɣɬɨ ɩɨɞɞɴɪɠɚɳ ɬɟɯɧɢɱɟɫɤɚɬɚ ɞɨɤɭɦɟɧɬɚɰɢɹ ɢ ɟ ɨɬɨɪɢɡɢɪɚɧ ɞɚ ɢɡɝɨɬɜɢ ɬɟɯɧɢɱɟɫɤɢɹ
ɮɚɣɥ ɢ ɟ ɪɟɝɢɫɬɪɢɪɚɧ ɜ ɨɛɳɧɨɫɬɬɚ.
Podpis osoby oprávnČné sestavit prohlášení jménem výrobce, držet technickou dokumentaci a osoby oprávnČné sestavit technické soubory a založené v rámci Evropského spoleþenství.
Underskrift af personen, der har fuldmagt til at udarbejde erklæringen på vegne af producenten, der er indehaver af dokumentationen og er bemyndiget til at udarbejde den tekniske
journal, og som er baseret på stedet.
Handtekening van de persoon die bevoegd is de verklaring namens de fabrikant te tekenen, de technische documentatie bewaart en bevoegd is om het technische bestand samen te
stellen, en die is gevestigd in het Woongebied.
Ühenduse registrisse kantud isiku allkiri, kes on volitatud tootja nimel deklaratsiooni koostama, kes omab tehnilist dokumentatsiooni ja kellel on õigus koostada tehniline toimik.
Sen henkilön allekirjoitus, jolla on valmistajan valtuutus vakuutuksen laadintaan, jolla on hallussaan tekniset asiakirjat, joka on valtuutettu laatimaan tekniset asiakirjat ja joka on
sijoittautunut yhteisöön.
Signature de la personne habilitée à rédiger la déclaration au nom du fabricant, à détenir la documentation technique, à compiler les fichiers techniques et qui est implantée dans la
Communauté.
Unterschrift der Person, die berechtigt ist, die Erklärung im Namen des Herstellers abzugeben, die die technischen Unterlagen aufbewahrt und berechtigt ist, die technischen Unterlagen
zusammenzustellen, und die in der Gemeinschaft niedergelassen ist.
ȊʌȠȖȡĮijȒ ĮIJȩȝȠȣ İȟȠȣıȚȠįȠIJȘȝȑȞȠȣ ȖȚĮ IJȘȞ ıȪȞIJĮȟȘ IJȘȢ įȒȜȦıȘȢ İț ȝȑȡȠȣȢ IJȠȣ țĮIJĮıțİȣĮıIJȒ, Ƞ ȠʌȠȓȠȢ țĮIJȑȤİȚ IJȘȞ IJİȤȞȚțȒ ȑțșİıȘ țĮȚ ȑȤİȚ IJȘȞ İȟȠȣıȚȠįȩIJȘıȘ ȞĮ IJĮȟȚȞȠȝȒıİȚ IJȠȞ IJİȤȞȚțȩ
ijȐțİȜȠ țĮȚ Ƞ ȠʌȠȓȠȢ İȓȞĮȚ įȚȠȡȚıȝȑȞȠȢ ıIJȘȞ ȀȠȚȞȩIJȘIJĮ.
A gyártó nevében meghatalmazott személy, akinek jogában áll módosítania a nyilatkozatot, a mĦszaki dokumentációt Ęrzi, engedéllyel rendelkezik a mĦszaki fájl összeállításához és a
közösségben letelepedett személy.
Firma della persona autorizzata a redigere la dichiarazione a nome del fabbricante, in possesso della documentazione tecnica ed autorizzata a costituire il fascicolo tecnico, che deve
essere stabilita nella Comunità.
TƗs personas paraksts, kura ir pilnvarota deklarƗcijas sastƗdƯšanai ražotƗja vƗrdƗ, kurai ir tehniskƗ dokumentƗcija, kura ir pilnvarota sagatavot tehnisko reƧistru un kura ir apstiprinƗta
KopienƗ.
Tim Lansdell
Technical Director
4th January 2010
Ransomes Jacobsen Limited
West Road, Ransomes Europark,
Ipswich, England, IP3 9TT
Asmuo, kuris yra gana žinomas, kuriam gamintojas suteikơ Ƴgaliojimus sudaryti šią deklaraciją, ir kuris ją pasirašơ, turi visą techninĊ informaciją ir yra Ƴgaliotas sudaryti techninơs
informacijos dokumentą.
Il-firma tal-persuna awtorizzata li tfassal id-dikjarazzjoni f’isem il-fabbrikant, gƫandha d-dokumentazzjoni teknika u hija awtorizzata li tikkompila l-fajl tekniku u li hija stabbilita fil-Komunità.
Podpis osoby upowaĪnionej do sporządzenia deklaracji w imieniu producenta, przechowującej dokumentacjĊ techniczną, upowaĪnioną do stworzenia dokumentacji technicznej oraz
wyznaczonej ds. wspólnotowych.
Assinatura da pessoa com poderes para emitir a declaração em nome do fabricante, que possui a documentação técnica, que está autorizada a compilar o processo técnico e que está
estabelecida na Comunidade.
Semnătura persoanei împuternicite să elaboreze declaraĠia în numele producătorului, care deĠine documentaĠia tehnică, este autorizată să compileze dosarul tehnic úi este stabilită în
Comunitate.
Podpis osoby poverenej vystavením vyhlásenia v mene výrobcu, ktorá má technickú dokumentáciu a je oprávnená spracovaĢ technické podklady a ktorá je umiestnená v Spoloþenstve.
Podpis osebe, pooblašþene za izdelavo izjave v imenu proizvajalca, ki ima tehniþno dokumentacijo in lahko sestavlja spis tehniþne dokumentacije, ter ima sedež v Skupnosti.
Firma de la persona responsable de la declaración en nombre del fabricante, que posee la documentación técnica y está autorizada para recopilar el archivo técnico y que está
establecido en la Comunidad.
Undertecknas av någon som bemyndigad att upprätta deklarationen å tillverkarens vägnar, innehar den tekniska dokumentationen och är bemyndigad att sammanställa den tekniska
informationen och som är etablerad i gemenskapen.
Undirskrift aðilans sem hefur umboð til að gera yfirlýsinguna fyrir hönd framleiðandans, hefur undir höndum tæknigögnin og hefur leyfi til að taka saman tækniskýrsluna, og er
viðurkenndur innan evrópska efnahagssvæðisins.
Signaturen til personen som har fullmakt til å utferdige erklæringen på vegne av produsenten, er i besittelse av den tekniske dokumentasjonen, har autorisasjon til å utarbeide den
tekniske filen og som har tilhold i EU.
Certificate Number ƒ ɇɨɦɟɪ ɧɚ ɫɟɪɬɢɮɢɤɚɬ ƒ ýíslo osvČdþení ƒ Certifikatnummer ƒ Certificaatnummer ƒ Sertifikaadi number ƒ Hyväksyntänumero ƒ Numéro de certificat ƒ
Bescheinigungsnummer ƒ ǹȡȚșȝȩȢ ȆȚıIJȠʌȠȚȘIJȚțȠȪ ƒ Hitelesítési szám ƒ
Numero del certificato ƒ SertifikƗta numurs ƒ Sertifikato numeris ƒ Numru taƛ-ƚertifikat ƒ Numer certyfikatu ƒ Número do Certificado ƒ Număr certificat ƒ ýíslo osvedþenia ƒ Številka
certifikata ƒ Número de certificado ƒ Certifikatsnummer ƒ Númer skírteinis ƒ Sertifikatnummer
PW2250WB-Incorp-r3
en-15
4
SPECIFICATIONS
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
DECLARATION OF CONFORMITY ƒ ȾȿɄɅȺɊȺɐɂə ɁȺ ɋɔɈɌȼȿɌɋɌȼɂȿ ƒ PROHLÁŠENÍ O SHODċ ƒ
OVERENSSTEMMELSESERKLÆRING ƒ CONFORMITEITSVERKLARING ƒ VASTAVUSDEKLARATSIOON ƒ
VAATIMUSTENMUKAISUUSVAKUUTUS ƒ DECLARATION DE CONFORMITE ƒ KONFORMITÄTSERKLÄRUNG ƒ ǻǾȁȍȈǾ
ȈȊȂȂȅȇĭȍȈǾȈ ƒ MEGFELELėSÉGI NYILATKOZAT ƒ DICHIARAZIONE DI CONFORMITÀ ƒ ATBILSTƮBAS DEKLARƖCIJA ƒ
ATITIKTIES DEKLARACIJA ƒ DIKJARAZZJONI TAL-KONFORMITÀ ƒ DEKLARACJA ZGODNOĝCI ƒ DECLARAÇÃO DE
CONFORMIDADE ƒ DECLARAğIE DE CONFORMITATE ƒ VYHLÁSENIE O ZHODE ƒ IZJAVA O SKLADNOSTI ƒ DECLARACIÓN DE
CONFORMIDAD ƒ DEKLARATION OM ÖVERENSSTÄMMELSE ƒ SAMRÆMISYFIRLÝSING ƒ KONFORMITETSERKLÆRING
Business name and full address of the manufacturer ƒ Ɍɴɪɝɨɜɫɤɨ ɢɦɟ ɢ ɩɴɥɟɧ ɚɞɪɟɫ ɧɚ ɩɪɨɢɡɜɨɞɢɬɟɥɹ ƒ
Obchodní jméno a plná adresa výrobce ƒ Producentens firmanavn og fulde adresse ƒ Bedrijfsnaam en volledig adres van de fabrikant ƒ Tootja ärinimi ja täielik aadress ƒ
Valmistajan toiminimi ja täydellinen osoite ƒ Nom commercial et adresse complète du fabricant ƒ Firmenname und vollständige Adresse des Herstellers ƒ ǼʌȦȞȣȝȓĮ țĮȚ
IJĮȤȣįȡȠȝȚțȒ įȚİȪșȣȞıȘ țĮIJĮıțİȣĮıIJȒ ƒ A gyártó üzleti neve és teljes címe ƒ Ragione sociale e indirizzo completo del fabbricante ƒ UzƼƝmuma nosaukums un pilna ražotƗja
adrese ƒ Verslo pavadinimas ir pilnas gamintojo adresas ƒ Isem kummerƛjali u indirizz sƫiƫ tal-fabbrikant ƒ Nazwa firmy i peãny adres producenta ƒ Nome da empresa e endereço
completo do fabricante ƒ Denumirea comercială úi adresa completă a producătorului ƒ Obchodný názov a úplná adresa výrobcu ƒ Naziv podjetja in polni naslov proizvajalca ƒ
Nombre de la empresa y dirección completa del fabricante ƒ Tillverkarens företagsnamn och kompletta adress ƒ Fyrirtækisheiti og fullt heimilisfang framleiðanda ƒ Firmanavn og
full adresse for produsenten
Ransomes Jacobsen Limited
West Road, Ransomes Europark,
Ipswich, England, IP3 9TT
Product Code ƒ Ʉɨɞ ɧɚ ɩɪɨɞɭɤɬɚ ƒ Kód výrobku ƒ Produktkode ƒ Productcode ƒ Toote kood ƒ Tuotekoodi ƒ Code produit ƒ Produktcode ƒ ȀȦįȚțȩȢ ʌȡȠȧȩȞIJȠȢ ƒ Termékkód ƒ
Codice prodotto ƒ Produkta kods ƒ Produkto kodas ƒ Kodiƛi tal-Prodott ƒ Kod produktu ƒ Código do Produto ƒ Cod produs ƒ Kód výrobku ƒ Oznaka proizvoda ƒ Código de producto
ƒ Produktkod ƒ Vörunúmer ƒ Produktkode
LMAC323
Machine Name ƒ ɇɚɢɦɟɧɨɜɚɧɢɟ ɧɚ ɦɚɲɢɧɚɬɚ ƒ Název stroje ƒ Maskinnavn ƒ Machinenaam ƒ Masina nimi ƒ Laitteen nimi ƒ Nom de la machine ƒ Maschinenbezeichnung ƒ
ȅȞȠȝĮıȓĮ ȝȘȤĮȞȒȝĮIJȠȢ ƒ Gépnév ƒ Denominazione della macchina ƒ IekƗrtas nosaukums ƒ Mašinos pavadinimas ƒ Isem tal-Magna ƒ Nazwa urządzenia ƒ Nome da Máquina ƒ
Numele echipamentului ƒ Názov stroja ƒ Naziv stroja ƒ Nombre de la máquina ƒ Maskinens namn ƒ Heiti tækis ƒ Maskinnavn
Ransomes Highway 2130 &
Parkway 2250+ ROPS Frame
Designation ƒ ɉɪɟɞɧɚɡɧɚɱɟɧɢɟ ƒ Oznaþení ƒ Betegnelse ƒ Benaming ƒ Nimetus ƒ Tyyppimerkintä ƒ Pažymơjimas ƒ
Bezeichnung ƒ ȋĮȡĮțIJȘȡȚıȝȩȢ ƒ Megnevezés ƒ Funzione ƒ ApzƯmƝjums ƒ Lithuanian ƒ Denominazzjoni ƒ Oznaczenie ƒ
Designação ƒ SpecificaĠie ƒ Oznaþenie ƒ Namen stroja ƒ Descripción ƒ Beteckning ƒ Merking ƒ Konstruksjon
ROPS Frame
Serial Number ƒ ɋɟɪɢɟɧ ɧɨɦɟɪ ƒ Sériové þíslo ƒ Serienummer ƒ Serienummer ƒ Seerianumber ƒ Valmistusnumero ƒ Numéro de série ƒ Seriennummer ƒ ȈİȚȡȚĮțȩȢ ĮȡȚșȝȩȢ ƒ
Sorozatszám ƒ Numero di serie ƒ SƝrijas numurs ƒ Serijos numeris ƒ Numru Serjali ƒ Numer seryjny ƒ Número de Série ƒ Număr de serie ƒ Sériové þíslo ƒ Serijska številka ƒ
Número de serie ƒ Serienummer ƒ Raðnúmer ƒ Serienummer
Not Applicable
Engine ƒ Ⱦɜɢɝɚɬɟɥ ƒ Motor ƒ Motor ƒ Motor ƒ Mootor ƒ Moottori ƒ Moteur ƒ Motor ƒ ȂȘȤĮȞȒ ƒ Modulnév ƒ Motore ƒ DzinƝjs ƒ Variklis ƒ Saƫƫa Netta Installata ƒ Silnik ƒ Motor ƒ Motor
ƒ Motor ƒ Motor ƒ Motor ƒ Motor ƒ Vél ƒ Motor
Not Applicable
Net Installed Power ƒ ɇɟɬɧɚ ɢɧɫɬɚɥɢɪɚɧɚ ɦɨɳɧɨɫɬ ƒ ýistý instalovaný výkon ƒ Installeret nettoeffekt ƒ Netto geïnstalleerd vermogen ƒ Installeeritud netovõimsus ƒ Asennettu
nettoteho ƒ Puissance nominale nette ƒ Installierte Nettoleistung ƒ ȀĮșĮȡȒ İȖțĮIJİıIJȘȝȑȞȘ ȚıȤȪȢ ƒ Nettó beépített teljesítmény ƒ Potenza netta installata ƒ ParedzƝtƗ tƯkla jauda ƒ
Grynoji galia ƒ Wisa’ tal-Qtugƫ ƒ Moc zainstalowana netto ƒ Potência instalada ƒ Puterea instalată netă ƒ ýistý inštalovaný výkon ƒ Neto vgrajena moþ ƒ Potencia instalada neta ƒ
Nettoeffekt ƒ Nettóafl vélar ƒ Netto installert kraft
Not Applicable
Cutting Width ƒ ɒɢɪɨɱɢɧɚ ɧɚ ɪɹɡɚɧɟ ƒ ŠíĜka Ĝezu ƒ Skærebredde ƒ Maaibreedte ƒ Lõikelaius ƒ Leikkuuleveys ƒ Largeur de coupe ƒ Schnittbreite ƒ ȂȒțȠȢ ȝȚıȚȞȑȗĮȢ ƒ Vágási
szélesség ƒ Larghezza di taglio ƒ Griešanas platums ƒ Pjovimo plotis ƒ Tikkonforma mad-Direttivi ƒ SzerokoĞü ciĊcia ƒ Largura de Corte ƒ LăĠimea de tăiere ƒ Šírka záberu ƒ Širina
reza ƒ Anchura de corte ƒ Klippbredd ƒ Skurðbreidd ƒ Klippebredde
Not Applicable
Conforms to Directives ƒ ȼ ɫɴɨɬɜɟɬɫɬɜɢɟ ɫ ɞɢɪɟɤɬɢɜɢɬɟ ƒ SplĖuje podmínky smČrnic ƒ Er i overensstemmelse med direktiver ƒ Voldoet aan de richtlijnen ƒ Vastab direktiividele ƒ
Direktiivien mukainen ƒ Conforme aux directives ƒ Entspricht Richtlinien ƒ ǹțȠȜȠȣșȒıIJİ ʌȚıIJȐ IJȚȢ ȅįȘȖȓİȢ ƒ Megfelel az irányelveknek ƒ Conforme alle Direttive ƒ Atbilst
direktƯvƗm ƒ Atitinka direktyvǐ reikalavimus ƒ Valutazzjoni tal-Konformità ƒ Dyrektywy związane ƒ Cumpre as Directivas ƒ Respectă Directivele ƒ Je v súlade so smernicami ƒ
Skladnost z direktivami ƒ Cumple con las Directivas ƒ Uppfyller direktiv ƒ Samræmist tilskipunum ƒ I samsvar med direktiv
Conformity Assessment ƒ Ɉɰɟɧɤɚ ɡɚ ɫɴɨɬɜɟɬɫɬɜɢɟ ƒ Hodnocení plnČní podmínek ƒ Overensstemmelsesvurdering ƒ
Conformiteitsbeoordeling ƒ Vastavushindamine ƒ Vaatimustenmukaisuuden arviointi ƒ Evaluation de conformité ƒ
Konformitätsbeurteilung ƒ ǻȚĮʌȓıIJȦıȘ ȈȣȝȝȩȡijȦıȘȢ ƒ MegfelelĘség-értékelés ƒ Valutazione della conformità ƒ
AtbilstƯbas novƝrtƝjums ƒ Atitikties Ƴvertinimas ƒ Livell tal-Qawwa tal-ƪoss Imkejjel ƒ Ocena zgodnoĞci ƒ
Avaliação de Conformidade ƒ Evaluarea conformităĠii ƒ Vyhodnotenie zhodnosti ƒ Ocena skladnosti ƒ
Evaluación de conformidad ƒ Bedömning av överensstämmelse ƒ Samræmismat ƒ Konformitetsvurdering
2006/42/EC
2006/42/EC Annex VIII
Measured Sound Power Level ƒ ɂɡɦɟɪɟɧɨ ɧɢɜɨ ɧɚ ɡɜɭɤɨɜɚ ɦɨɳɧɨɫɬ ƒ NamČĜený akustický výkon ƒ Målte lydstyrkeniveau ƒ Gemeten geluidsniveau ƒ Mõõdetud helivõimsuse
tase ƒ Mitattu äänitehotaso ƒ Niveau de puissance sonore mesuré ƒ Gemessener Schalldruckpegel ƒ ȈIJĮșȝȚıȝȑȞȠ İʌȓʌİįȠ ȘȤȘIJȚțȒȢ ȚıȤȪȠȢ ƒ Mért hangteljesítményszint ƒ Livello
di potenza sonora misurato ƒ IzmƝrƯtais skaƼas jaudas lƯmenis ƒ Išmatuotas garso stiprumo lygis ƒ Livell tal-Qawwa tal-ƪoss Iggarantit ƒ Moc akustyczna mierzona ƒ Nível sonoro
medido ƒ Nivelul măsurat al puterii acustice ƒ Nameraná hladina akustického výkonu ƒ Izmerjena raven zvoþne moþi ƒ Nivel de potencia sonora medido ƒ Uppmätt ljudeffektsnivå
ƒ Mælt hljóðaflsstig ƒ Målt lydeffektnivå
Not Applicable
Guaranteed Sound Power Level ƒ Ƚɚɪɚɧɬɢɪɚɧɨ ɧɢɜɨ ɧɚ ɡɜɭɤɨɜɚ ɦɨɳɧɨɫɬ ƒ Garantovaný akustický výkon ƒ Garanteret lydstyrkeniveau ƒ Gegarandeerd geluidsniveau ƒ
Garanteeritud helivõimsuse tase ƒ Taattu äänitehotaso ƒ Niveau de puissance sonore garanti ƒ Garantierter Schalldruckpegel ƒ ǼȖȖȣȘȝȑȞȠ İʌȓʌİįȠ ȘȤȘIJȚțȒȢ ȚıȤȪȠȢ ƒ Szavatolt
hangteljesítményszint ƒ Livello di potenza sonora garantito ƒ GarantƝtais skaƼas jaudas lƯmenis ƒ Garantuotas garso stiprumo lygis ƒ Livell tal-Qawwa tal-ƪoss Iggarantit ƒ Moc
akustyczna gwarantowana ƒ Nível sonoro farantido ƒ Nivelul garantat al puterii acustice ƒ Garantovaná hladina akustického výkonu ƒ Zajamþena raven zvoþne moþi ƒ Nivel de
potencia sonora garantizado ƒ Garanterad ljudeffektsnivå ƒ Hljóðaflsstig sem ábyrgð er tekin á ƒ Garanter lydeffektnivå
Not Applicable
Conformity Assessment Procedure (Noise) ƒ Ɉɰɟɧɤɚ ɡɚ ɫɴɨɬɜɟɬɫɬɜɢɟ ɧɚ ɩɪɨɰɟɞɭɪɚɬɚ (ɒɭɦ) ƒ
Postup hodnocení plnČní podmínek (hluk) ƒ Procedure for overensstemmelsesvurdering (Støj) ƒ
Procedure van de conformiteitsbeoordeling (geluid) ƒ Vastavushindamismenetlus (müra) ƒ
Vaatimustenmukaisuuden arviointimenettely (Melu) ƒ Procédure d’évaluation de conformité (bruit) ƒ
Konformitätsbeurteilungsverfahren (Geräusch) ƒ ǻȚĮįȚțĮıȓĮ ǹȟȚȠȜȩȖȘıȘȢ ȈȣȝȝȩȡijȦıȘȢ (ĬȩȡȣȕȠȢ) ƒ
MegfelelĘség-értékelési eljárás (Zaj) ƒ Procedura di valutazione della conformità (rumore) ƒ
AtbilstƯbas novƝrtƝjuma procednjra (troksnis) ƒ Atitikties Ƴvertinimo procednjra (garsas) ƒ
Proƛedura tal-Valutazzjoni tal-Konformità (ƪoss) ƒ Procedura oceny zgodnoĞci (poziom haãasu) ƒ
Processo de avaliação de conformidade (nível sonoro) Procedura de evaluare a conformităĠii (zgomot) ƒ
Postup vyhodnocovania zhodnosti (hluk) ƒ Postopek za ugotavljanje skladnosti (hrup) ƒ
Procedimiento de evaluación de conformidad (ruido) ƒ Procedur för bedömning av överensstämmelse (buller)
ƒ Samræmismatsaðferð (hávaði) ƒ Prosedyre for konformitetsvurdering (støy)
Not Applicable
UK Notified Body for 2000/14/EC ƒ ɇɨɬɢɮɢɰɢɪɚɧ ɨɪɝɚɧ ɜ Ɉɛɟɞɢɧɟɧɨɬɨ ɤɪɚɥɫɬɜɨ ɡɚ 2000/14/ȿɈ ƒ ÚĜad certifikovaný podle smČrnice þ. 2000/14/EC ƒ Det britiske
bemyndigede organ for 2001/14/EF ƒ Engels adviesorgaan voor 2000/14/EG ƒ Ühendkuningriigi teavitatud asutus direktiivi 2000/14/EÜ mõistes ƒ Direktiivin 2000/14/EY
mukainen ilmoitettu tarkastuslaitos Isossa-Britanniassa ƒ Organisme notifié concernant la directive 2000/14/CE ƒ Britische benannte Stelle für 2000/14/EG ƒ ȀȠȚȞȠʌȠȚȘȝȑȞȠȢ
ȅȡȖĮȞȚıȝȩȢ ǾȞȦȝȑȞȠȣ ǺĮıȚȜİȓȠȣ ȖȚĮ 2000/14/ǼȀ ƒ 2000/14/EK – egyesült királyságbeli bejelentett szervezet ƒ Organismo Notificato in GB per 2000/14/CE ƒ 2000/14/EK AK
reƧistrƝtƗ organizƗcija ƒ JK notifikuotosios Ƴstaigos 2000/14/EC ƒ Korp Notifikat tar-Renju Unit gƫal 2000/14/KE ƒ Dopuszczona jednostka badawcza w Wielkiej Brytanii wg
2000/14/WE ƒ Entidade notificada no Reino Unido para 2000/14/CE ƒ Organism notificat în Marea Britanie pentru 2000/14/CE ƒ Notifikovaný orgán Spojeného kráĐovstva pre
smernicu 2000/14/ES ƒ Britanski priglašeni organ za 2000/14/ES ƒ Cuerpo notificado en el Reino Unido para 2000/14/CE ƒ Anmält organ för 2000/14/EG i Storbritannien ƒ
Tilkynntur aðili í Bretlandi fyrir 2000/14/EC ƒ Britisk teknisk for 2000/14/EF
en-16
Number: 1088
Sound Research Laboratories Limited
Holbrook House, Little Waldingfield
Sudbury, Suffolk CO10 0TH
4
SPECIFICATIONS
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
Operator Ear Noise Level ƒ Ɉɩɟɪɚɬɨɪ ɧɚ ɧɢɜɨɬɨ ɧɚ ɞɨɥɨɜɢɦ ɨɬ ɭɯɨɬɨ ɲɭɦ ƒ
Hladina hluku v oblasti uší operátora ƒ Støjniveau i førers ørehøjde ƒ
Geluidsniveau oor bestuurder ƒ Müratase operaatori kõrvas ƒ
Melutaso käyttäjän korvan kohdalla ƒ Niveau de bruit à hauteur des oreilles de l’opérateur ƒ
Schallpegel am Bedienerohr ƒ ǼʌȓʌİįȠ șȠȡȪȕȠȣ ıİ ȜİȚIJȠȣȡȖȓĮ ƒ
A kezelĘ fülénél mért zajszint ƒ Livello di potenza sonora all’orecchio dell’operatore ƒ
TrokšƼa lƯmenis pie operatora auss ƒ Dirbanþiojo su mašina patiriamo triukšmo lygis ƒ
Livell tal-ƪoss fil-Widna tal-Operatur ƒ Dopuszczalny poziom haãasu dla operatora ƒ
Nível sonoro nos ouvidos do operador ƒ Nivelul zgomotului la urechea operatorului ƒ
Hladina hluku pôsobiaca na sluch operátora ƒ Raven hrupa pri ušesu upravljavca ƒ
Nivel sonoro en el oído del operador ƒ Ljudnivå vid förarens öra ƒ Hávaðastig fyrir stjórnanda ƒ Støynivå ved operatørens øre
Harmonised standards used ƒ ɂɡɩɨɥɡɜɚɧɢ ɯɚɪɦɨɧɢɡɢɪɚɧɢ ɫɬɚɧɞɚɪɬɢ ƒ Použité harmonizované normy ƒ Brugte harmoniserede standarder ƒ Gebruikte geharmoniseerde
standaards ƒ Kasutatud ühtlustatud standardid ƒ Käytetyt yhdenmukaistetut standardit ƒ Normes harmonisées utilisées ƒ Angewandte harmonisierte Normen ƒ ǼȞĮȡȝȠȞȚıȝȑȞĮ
ʌȡȩIJȣʌĮ ʌȠȣ ȤȡȘıȚȝȠʌȠȚȒșȘțĮȞ ƒ Harmonizált szabványok ƒ Standard armonizzati applicati ƒ Izmantotie saskaƼotie standarti ƒ Panaudoti suderinti standartai ƒ Standards
armonizzati uĪati ƒ Normy spójne powiązane ƒ Normas harmonizadas usadas ƒ Standardele armonizate utilizate ƒ Použité harmonizované normy ƒ Uporabljeni usklajeni standardi
ƒ Estándares armonizados utilizados ƒ Harmoniserade standarder som används
Not Applicable
EN 836:1987
Technical standards and specifications used ƒ ɂɡɩɨɥɡɜɚɧɢ ɬɟɯɧɢɱɟɫɤɢ ɫɬɚɧɞɚɪɬɢ ɢ ɫɩɟɰɢɮɢɤɚɰɢɢ ƒ
Použité technické normy a specifikace ƒ Brugte tekniske standarder og specifikationer ƒ
Gebruikte technische standaards en specificaties ƒ Kasutatud tehnilised standardid ja spetsifikatsioonid ƒ
Käytetyt tekniset standardit ja eritelmät ƒ Spécifications et normes techniques utilisées ƒ
Angewandte technische Normen und Spezifikationen ƒ ȉİȤȞȚțȐ ʌȡȩIJȣʌĮ țĮȚ ʌȡȠįȚĮȖȡĮijȑȢ ʌȠȣ ȤȡȘıȚȝȠʌȠȚȒșȘțĮȞ ƒ MĦszaki szabványok és specifikációk ƒ Standard tecnici e
specifiche applicati ƒ
Izmantotie tehniskie standarti un specifikƗcijas ƒ Panaudoti techniniai standartai ir techninơ informacija ƒ
Standards u speƛifikazzjonijiet tekniƛi uĪati ƒ Normy i specyfikacje techniczne powiązane ƒ
Normas técnicas e especificações usadas ƒ Standardele tehnice úi specificaĠiile utilizate ƒ
Použité technické normy a špecifikácie ƒ Uporabljeni tehniþni standardi in specifikacije ƒ
Estándares y especificaciones técnicas utilizadas ƒ Tekniska standarder och specifikationer som används ƒ Samræmdir staðlar sem notaðir eru ƒ Benyttede harmoniserte
standarder
OECD Code 4 ROPS Static Test
(Report No. N950/08/14014)
The place and date of the declaration ƒ Ɇɹɫɬɨ ɢ ɞɚɬɚ ɧɚ ɞɟɤɥɚɪɚɰɢɹɬɚ ƒ Místo a datum prohlášení ƒ Sted og dato for erklæringen ƒ Plaats en datum van de verklaring ƒ
Deklaratsiooni väljastamise koht ja kuupäev ƒ Vakuutuksen paikka ja päivämäärä ƒ Lieu et date de la déclaration ƒ Ort und Datum der Erklärung ƒ ȉȩʌȠȢ țĮȚ ȘȝİȡȠȝȘȞȓĮ
įȒȜȦıȘȢ ƒ A nyilatkozat kelte (hely és idĘ) ƒ Luogo e data della dichiarazione ƒ DeklarƗcijas vieta un datums ƒ Deklaracijos vieta ir data ƒ Il-post u d-data tad-dikjarazzjoni ƒ
Miejsce i data wystawienia deklaracji ƒ Local e data da declaração ƒ Locul úi data declaraĠiei ƒ Miesto a dátum vyhlásenia ƒ Kraj in datum izjave ƒ Lugar y fecha de la declaración
ƒ Plats och datum för deklarationen ƒ Tæknistaðlar og tæknilýsingar sem notaðar eru ƒ Benyttede tekniske standarder og spesifikasjoner ƒ Staður og dagsetning yfirlýsingar ƒ
Sted og dato for erklæringen
Ransomes Jacobsen Limited
West Road, Ransomes Europark,
Ipswich, England, IP3 9TT
4th January 2010
Signature of the person empowered to draw up the declaration on behalf of the manufacturer, holds the technical documentation and is authorised to compile the technical file, and who is
established in the Community.
ɉɨɞɩɢɫ ɧɚ ɱɨɜɟɤɚ, ɭɩɴɥɧɨɦɨɳɟɧ ɞɚ ɫɴɫɬɚɜɢ ɞɟɤɥɚɪɚɰɢɹɬɚ ɨɬ ɢɦɟɬɨ ɧɚ ɩɪɨɢɡɜɨɞɢɬɟɥɹ, ɤɨɣɬɨ ɩɨɞɞɴɪɠɚɳ
ɬɟɯɧɢɱɟɫɤɚɬɚ ɞɨɤɭɦɟɧɬɚɰɢɹ ɢ ɟ ɨɬɨɪɢɡɢɪɚɧ ɞɚ ɢɡɝɨɬɜɢ ɬɟɯɧɢɱɟɫɤɢɹ ɮɚɣɥ ɢ ɟ ɪɟɝɢɫɬɪɢɪɚɧ ɜ ɨɛɳɧɨɫɬɬɚ.
Podpis osoby oprávnČné sestavit prohlášení jménem výrobce, držet technickou dokumentaci a osoby oprávnČné
sestavit technické soubory a založené v rámci Evropského spoleþenství.
Underskrift af personen, der har fuldmagt til at udarbejde erklæringen på vegne af producenten, der er indehaver
af dokumentationen og er bemyndiget til at udarbejde den tekniske journal, og som er baseret i nærområdet.
Handtekening van de persoon die bevoegd is de verklaring namens de fabrikant te tekenen, de technische
documentatie bewaart en bevoegd is om het technische bestand samen te stellen, en die is gevestigd in het Woongebied.
Ühenduse registrisse kantud isiku allkiri, kes on volitatud tootja nimel deklaratsiooni koostama, kes omab tehnilist
dokumentatsiooni ja kellel on õigus koostada tehniline toimik.
Sen henkilön allekirjoitus, jolla on valmistajan valtuutus vakuutuksen laadintaan, jolla on hallussaan tekniset
asiakirjat, joka on valtuutettu laatimaan tekniset asiakirjat ja joka on sijoittautunut yhteisöön.
Signature de la personne habilitée à rédiger la déclaration au nom du fabricant, à détenir la documentation
technique, à compiler les fichiers techniques et qui est implantée dans la Communauté.
Unterschrift der Person, die berechtigt ist, die Erklärung im Namen des Herstellers abzugeben, die die
technischen Unterlagen aufbewahrt und berechtigt ist, die technischen Unterlagen zusammenzustellen,
und die in der Gemeinschaft niedergelassen ist.
ȊʌȠȖȡĮijȒ ĮIJȩȝȠȣ İȟȠȣıȚȠįȠIJȘȝȑȞȠȣ ȖȚĮ IJȘȞ ıȪȞIJĮȟȘ IJȘȢ įȒȜȦıȘȢ İț ȝȑȡȠȣȢ IJȠȣ țĮIJĮıțİȣĮıIJȒ, Ƞ ȠʌȠȓȠȢ
țĮIJȑȤİȚ IJȘȞ IJİȤȞȚțȒ ȑțșİıȘ țĮȚ ȑȤİȚ IJȘȞ İȟȠȣıȚȠįȩIJȘıȘ ȞĮ IJĮȟȚȞȠȝȒıİȚ IJȠȞ IJİȤȞȚțȩ ijȐțİȜȠ țĮȚ Ƞ ȠʌȠȓȠȢ İȓȞĮȚ įȚȠȡȚıȝȑȞȠȢ ıIJȘȞ ȀȠȚȞȩIJȘIJĮ.
A gyártó nevében meghatalmazott személy, akinek jogában áll módosítania a nyilatkozatot, a mĦszaki
dokumentációt Ęrzi, engedéllyel rendelkezik a mĦszaki fájl összeállításához, és aki a közösségben letelepedett személy.
Firma della persona autorizzata a redigere la dichiarazione a nome del fabbricante, in possesso Della
documentazione tecnica ed autorizzata a costituire il fascicolo tecnico, che deve essere stabilita nella Comunità.
TƗs personas paraksts, kura ir pilnvarota deklarƗcijas sastƗdƯšanai ražotƗja vƗrdƗ, kurai ir tehniskƗ
dokumentƗcija, kura ir pilnvarota sagatavot tehnisko reƧistru un kura ir apstiprinƗta KopienƗ.
Asmuo, kuris yra gana žinomas, kuriam gamintojas suteikơ Ƴgaliojimus sudaryti šią deklaraciją, ir kuris ją
pasirašơ, turi visą techninĊ informaciją ir yra Ƴgaliotas sudaryti techninơs informacijos dokumentą.
Il-firma tal-persuna awtorizzata li tfassal id-dikjarazzjoni f’isem il-fabbrikant, gƫandha d-dokumentazzjoni
teknika u hija awtorizzata li tikkompila l-fajl tekniku u li hija stabbilita fil-Komunità.
Podpis osoby upowaĪnionej do sporządzenia deklaracji w imieniu producenta, przechowującej dokumentacjĊ
techniczną, upowaĪnioną do stworzenia dokumentacji technicznej oraz wyznaczonej ds. wspólnotowych.
Assinatura da pessoa com poderes para emitir a declaração em nome do fabricante, que possui a documentação
técnica, que está autorizada a compilar o processo técnico e que está estabelecida na Comunidade.
Semnătura persoanei împuternicite să elaboreze declaraĠia în numele producătorului, care deĠine documentaĠia
tehnică, este autorizată să compileze dosarul tehnic úi este stabilită în Comunitate.
Podpis osoby poverenej vystavením vyhlásenia v mene výrobcu, ktorá má technickú dokumentáciu a je
oprávnená spracovaĢ technické podklady a ktorá je umiestnená v Spoloþenstve.
Podpis osebe, pooblašþene za izdelavo izjave v imenu proizvajalca, ki ima tehniþno dokumentacijo in lahko
sestavlja spis tehniþne dokumentacije, ter ima sedež v Skupnosti.
Firma de la persona responsable de la declaración en nombre del fabricante, que posee la documentación técnica
y está autorizada para recopilar el archivo técnico y que está establecido en la Comunidad.
Undertecknas av den som bemyndigad att upprätta deklarationen å tillverkarens vägnar, innehar den tekniska
dokumentationen och är bemyndigad att sammanställa den tekniska informationen och som är etablerad i
gemenskapen. Undirskrift aðilans sem hefur umboð til að gera yfirlýsinguna fyrir hönd framleiðandans, hefur undir höndum
tæknigögnin og hefur leyfi til að taka saman tækniskýrsluna, og er viðurkenndur innan evrópska efnahagssvæðisins.
Signaturen til personen som har fullmakt til å utferdige erklæringen på vegne av produsenten, er i besittelse av den
tekniske dokumentasjonen, har autorisasjon til å utarbeide den tekniske filen og som har tilhold i EU.
Tim Lansdell
Technical Director
4th January 2010
Ransomes Jacobsen Limited
West Road, Ransomes Europark,
Ipswich, England, IP3 9TT
Certificate Number ƒ ɇɨɦɟɪ ɧɚ ɫɟɪɬɢɮɢɤɚɬ ƒ ýíslo osvČdþení ƒ Certifikatnummer ƒ Certificaatnummer ƒ Sertifikaadi number ƒ Hyväksyntänumero ƒ Numéro de certificat ƒ
Bescheinigungsnummer ƒ ǹȡȚșȝȩȢ ȆȚıIJȠʌȠȚȘIJȚțȠȪ ƒ Hitelesítési szám ƒ Numero del certificato ƒ SertifikƗta numurs ƒ Sertifikato numeris ƒ Numru taƛ-ƚertifikat ƒ Numer
certyfikatu ƒ Número do Certificado ƒ Număr certificat ƒ ýíslo osvedþenia ƒ Številka certifikata ƒ Número de certificado ƒ Certifikatsnummer ƒ Númer skírteinis ƒ Sertifikatnummer
4180920-r1
en-17
4
SPECIFICATIONS
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
DECLARATION OF CONFORMITY ƒ ȾȿɄɅȺɊȺɐɂə ɁȺ ɋɔɈɌȼȿɌɋɌȼɂȿ ƒ PROHLÁŠENÍ O SHODċ ƒ
OVERENSSTEMMELSESERKLÆRING ƒ CONFORMITEITSVERKLARING ƒ VASTAVUSDEKLARATSIOON ƒ
VAATIMUSTENMUKAISUUSVAKUUTUS ƒ DECLARATION DE CONFORMITE ƒ KONFORMITÄTSERKLÄRUNG ƒ ǻǾȁȍȈǾ
ȈȊȂȂȅȇĭȍȈǾȈ ƒ MEGFELELėSÉGI NYILATKOZAT ƒ DICHIARAZIONE DI CONFORMITÀ ƒ ATBILSTƮBAS DEKLARƖCIJA ƒ
ATITIKTIES DEKLARACIJA ƒ DIKJARAZZJONI TAL-KONFORMITÀ ƒ DEKLARACJA ZGODNOĝCI ƒ DECLARAÇÃO DE
CONFORMIDADE ƒ DECLARAğIE DE CONFORMITATE ƒ VYHLÁSENIE O ZHODE ƒ IZJAVA O SKLADNOSTI ƒ DECLARACIÓN DE
CONFORMIDAD ƒ DEKLARATION OM ÖVERENSSTÄMMELSE ƒ SAMRÆMISYFIRLÝSING ƒ KONFORMITETSERKLÆRING
Business name and full address of the manufacturer ƒ Ɍɴɪɝɨɜɫɤɨ ɢɦɟ ɢ ɩɴɥɟɧ ɚɞɪɟɫ ɧɚ ɩɪɨɢɡɜɨɞɢɬɟɥɹ ƒ
Obchodní jméno a plná adresa výrobce ƒ Producentens firmanavn og fulde adresse ƒ Bedrijfsnaam en volledig adres van de fabrikant ƒ Tootja ärinimi ja täielik aadress ƒ
Valmistajan toiminimi ja täydellinen osoite ƒ Nom commercial et adresse complète du fabricant ƒ Firmenname und vollständige Adresse des Herstellers ƒ ǼʌȦȞȣȝȓĮ țĮȚ
IJĮȤȣįȡȠȝȚțȒ įȚİȪșȣȞıȘ țĮIJĮıțİȣĮıIJȒ ƒ A gyártó üzleti neve és teljes címe ƒ Ragione sociale e indirizzo completo del fabbricante ƒ UzƼƝmuma nosaukums un pilna ražotƗja
adrese ƒ Verslo pavadinimas ir pilnas gamintojo adresas ƒ Isem kummerƛjali u indirizz sƫiƫ tal-fabbrikant ƒ Nazwa firmy i peãny adres producenta ƒ Nome da empresa e endereço
completo do fabricante ƒ Denumirea comercială úi adresa completă a producătorului ƒ Obchodný názov a úplná adresa výrobcu ƒ Naziv podjetja in polni naslov proizvajalca ƒ
Nombre de la empresa y dirección completa del fabricante ƒ Tillverkarens företagsnamn och kompletta adress ƒ Fyrirtækisheiti og fullt heimilisfang framleiðanda ƒ Firmanavn og
full adresse for produsenten
Ransomes Jacobsen Limited
West Road, Ransomes Europark,
Ipswich, England, IP3 9TT
Product Code ƒ Ʉɨɞ ɧɚ ɩɪɨɞɭɤɬɚ ƒ Kód výrobku ƒ Produktkode ƒ Productcode ƒ Toote kood ƒ Tuotekoodi ƒ Code produit ƒ Produktcode ƒ ȀȦįȚțȩȢ ʌȡȠȧȩȞIJȠȢ ƒ Termékkód ƒ
Codice prodotto ƒ Produkta kods ƒ Produkto kodas ƒ Kodiƛi tal-Prodott ƒ Kod produktu ƒ Código do Produto ƒ Cod produs ƒ Kód výrobku ƒ Oznaka proizvoda ƒ Código de producto
ƒ Produktkod ƒ Vörunúmer ƒ Produktkode
LMAB653 & LMAB654
Machine Name ƒ ɇɚɢɦɟɧɨɜɚɧɢɟ ɧɚ ɦɚɲɢɧɚɬɚ ƒ Název stroje ƒ Maskinnavn ƒ Machinenaam ƒ Masina nimi ƒ Laitteen nimi ƒ Nom de la machine ƒ Maschinenbezeichnung ƒ
ȅȞȠȝĮıȓĮ ȝȘȤĮȞȒȝĮIJȠȢ ƒ Gépnév ƒ Denominazione della macchina ƒ IekƗrtas nosaukums ƒ Mašinos pavadinimas ƒ Isem tal-Magna ƒ Nazwa urządzenia ƒ Nome da Máquina ƒ
Numele echipamentului ƒ Názov stroja ƒ Naziv stroja ƒ Nombre de la máquina ƒ Maskinens namn ƒ Heiti tækis ƒ Maskinnavn
Designation ƒ ɉɪɟɞɧɚɡɧɚɱɟɧɢɟ ƒ Oznaþení ƒ Betegnelse ƒ Benaming ƒ Nimetus ƒ Tyyppimerkintä ƒ Pažymơjimas ƒ
Bezeichnung ƒ ȋĮȡĮțIJȘȡȚıȝȩȢ ƒ Megnevezés ƒ Funzione ƒ ApzƯmƝjums ƒ Lithuanian ƒ Denominazzjoni ƒ Oznaczenie ƒ
Designação ƒ SpecificaĠie ƒ Oznaþenie ƒ Namen stroja ƒ Descripción ƒ Beteckning ƒ Merking ƒ Konstruksjon
Ransomes Hhighway 2130 Cab Kit
Ransomes Parkway 2250+ Cab Kit
Dieteg ROPS cab and Fitting Kit
Serial Number ƒ ɋɟɪɢɟɧ ɧɨɦɟɪ ƒ Sériové þíslo ƒ Serienummer ƒ Serienummer ƒ Seerianumber ƒ Valmistusnumero ƒ Numéro de série ƒ Seriennummer ƒ ȈİȚȡȚĮțȩȢ ĮȡȚșȝȩȢ ƒ
Sorozatszám ƒ Numero di serie ƒ SƝrijas numurs ƒ Serijos numeris ƒ Numru Serjali ƒ Numer seryjny ƒ Número de Série ƒ Număr de serie ƒ Sériové þíslo ƒ Serijska številka ƒ
Número de serie ƒ Serienummer ƒ Raðnúmer ƒ Serienummer
Not Applicable
Engine ƒ Ⱦɜɢɝɚɬɟɥ ƒ Motor ƒ Motor ƒ Motor ƒ Mootor ƒ Moottori ƒ Moteur ƒ Motor ƒ ȂȘȤĮȞȒ ƒ Modulnév ƒ Motore ƒ DzinƝjs ƒ Variklis ƒ Saƫƫa Netta Installata ƒ Silnik ƒ Motor ƒ Motor
ƒ Motor ƒ Motor ƒ Motor ƒ Motor ƒ Vél ƒ Motor
Not Applicable
Net Installed Power ƒ ɇɟɬɧɚ ɢɧɫɬɚɥɢɪɚɧɚ ɦɨɳɧɨɫɬ ƒ ýistý instalovaný výkon ƒ Installeret nettoeffekt ƒ Netto geïnstalleerd vermogen ƒ Installeeritud netovõimsus ƒ Asennettu
nettoteho ƒ Puissance nominale nette ƒ Installierte Nettoleistung ƒ ȀĮșĮȡȒ İȖțĮIJİıIJȘȝȑȞȘ ȚıȤȪȢ ƒ Nettó beépített teljesítmény ƒ Potenza netta installata ƒ ParedzƝtƗ tƯkla jauda ƒ
Grynoji galia ƒ Wisa’ tal-Qtugƫ ƒ Moc zainstalowana netto ƒ Potência instalada ƒ Puterea instalată netă ƒ ýistý inštalovaný výkon ƒ Neto vgrajena moþ ƒ Potencia instalada neta ƒ
Nettoeffekt ƒ Nettóafl vélar ƒ Netto installert kraft
Not Applicable
Cutting Width ƒ ɒɢɪɨɱɢɧɚ ɧɚ ɪɹɡɚɧɟ ƒ ŠíĜka Ĝezu ƒ Skærebredde ƒ Maaibreedte ƒ Lõikelaius ƒ Leikkuuleveys ƒ Largeur de coupe ƒ Schnittbreite ƒ ȂȒțȠȢ ȝȚıȚȞȑȗĮȢ ƒ Vágási
szélesség ƒ Larghezza di taglio ƒ Griešanas platums ƒ Pjovimo plotis ƒ Tikkonforma mad-Direttivi ƒ SzerokoĞü ciĊcia ƒ Largura de Corte ƒ LăĠimea de tăiere ƒ Šírka záberu ƒ Širina
reza ƒ Anchura de corte ƒ Klippbredd ƒ Skurðbreidd ƒ Klippebredde
Not Applicable
Conforms to Directives ƒ ȼ ɫɴɨɬɜɟɬɫɬɜɢɟ ɫ ɞɢɪɟɤɬɢɜɢɬɟ ƒ SplĖuje podmínky smČrnic ƒ Er i overensstemmelse med direktiver ƒ Voldoet aan de richtlijnen ƒ Vastab direktiividele ƒ
Direktiivien mukainen ƒ Conforme aux directives ƒ Entspricht Richtlinien ƒ ǹțȠȜȠȣșȒıIJİ ʌȚıIJȐ IJȚȢ ȅįȘȖȓİȢ ƒ Megfelel az irányelveknek ƒ Conforme alle Direttive ƒ Atbilst
direktƯvƗm ƒ Atitinka direktyvǐ reikalavimus ƒ Valutazzjoni tal-Konformità ƒ Dyrektywy związane ƒ Cumpre as Directivas ƒ Respectă Directivele ƒ Je v súlade so smernicami ƒ
Skladnost z direktivami ƒ Cumple con las Directivas ƒ Uppfyller direktiv ƒ Samræmist tilskipunum ƒ I samsvar med direktiv
Conformity Assessment ƒ Ɉɰɟɧɤɚ ɡɚ ɫɴɨɬɜɟɬɫɬɜɢɟ ƒ Hodnocení plnČní podmínek ƒ Overensstemmelsesvurdering ƒ
Conformiteitsbeoordeling ƒ Vastavushindamine ƒ Vaatimustenmukaisuuden arviointi ƒ Evaluation de conformité ƒ
Konformitätsbeurteilung ƒ ǻȚĮʌȓıIJȦıȘ ȈȣȝȝȩȡijȦıȘȢ ƒ MegfelelĘség-értékelés ƒ Valutazione della conformità ƒ
AtbilstƯbas novƝrtƝjums ƒ Atitikties Ƴvertinimas ƒ Livell tal-Qawwa tal-ƪoss Imkejjel ƒ Ocena zgodnoĞci ƒ
Avaliação de Conformidade ƒ Evaluarea conformităĠii ƒ Vyhodnotenie zhodnosti ƒ Ocena skladnosti ƒ
Evaluación de conformidad ƒ Bedömning av överensstämmelse ƒ Samræmismat ƒ Konformitetsvurdering
86/298/EC
2006/42/EC Annex VIII
Measured Sound Power Level ƒ ɂɡɦɟɪɟɧɨ ɧɢɜɨ ɧɚ ɡɜɭɤɨɜɚ ɦɨɳɧɨɫɬ ƒ NamČĜený akustický výkon ƒ Målte lydstyrkeniveau ƒ Gemeten geluidsniveau ƒ Mõõdetud helivõimsuse
tase ƒ Mitattu äänitehotaso ƒ Niveau de puissance sonore mesuré ƒ Gemessener Schalldruckpegel ƒ ȈIJĮșȝȚıȝȑȞȠ İʌȓʌİįȠ ȘȤȘIJȚțȒȢ ȚıȤȪȠȢ ƒ Mért hangteljesítményszint ƒ Livello
di potenza sonora misurato ƒ IzmƝrƯtais skaƼas jaudas lƯmenis ƒ Išmatuotas garso stiprumo lygis ƒ Livell tal-Qawwa tal-ƪoss Iggarantit ƒ Moc akustyczna mierzona ƒ Nível sonoro
medido ƒ Nivelul măsurat al puterii acustice ƒ Nameraná hladina akustického výkonu ƒ Izmerjena raven zvoþne moþi ƒ Nivel de potencia sonora medido ƒ Uppmätt ljudeffektsnivå
ƒ Mælt hljóðaflsstig ƒ Målt lydeffektnivå
Not Applicable
Guaranteed Sound Power Level ƒ Ƚɚɪɚɧɬɢɪɚɧɨ ɧɢɜɨ ɧɚ ɡɜɭɤɨɜɚ ɦɨɳɧɨɫɬ ƒ Garantovaný akustický výkon ƒ Garanteret lydstyrkeniveau ƒ Gegarandeerd geluidsniveau ƒ
Garanteeritud helivõimsuse tase ƒ Taattu äänitehotaso ƒ Niveau de puissance sonore garanti ƒ Garantierter Schalldruckpegel ƒ ǼȖȖȣȘȝȑȞȠ İʌȓʌİįȠ ȘȤȘIJȚțȒȢ ȚıȤȪȠȢ ƒ Szavatolt
hangteljesítményszint ƒ Livello di potenza sonora garantito ƒ GarantƝtais skaƼas jaudas lƯmenis ƒ Garantuotas garso stiprumo lygis ƒ Livell tal-Qawwa tal-ƪoss Iggarantit ƒ Moc
akustyczna gwarantowana ƒ Nível sonoro farantido ƒ Nivelul garantat al puterii acustice ƒ Garantovaná hladina akustického výkonu ƒ Zajamþena raven zvoþne moþi ƒ Nivel de
potencia sonora garantizado ƒ Garanterad ljudeffektsnivå ƒ Hljóðaflsstig sem ábyrgð er tekin á ƒ Garanter lydeffektnivå
Not Applicable
Conformity Assessment Procedure (Noise) ƒ Ɉɰɟɧɤɚ ɡɚ ɫɴɨɬɜɟɬɫɬɜɢɟ ɧɚ ɩɪɨɰɟɞɭɪɚɬɚ (ɒɭɦ) ƒ
Postup hodnocení plnČní podmínek (hluk) ƒ Procedure for overensstemmelsesvurdering (Støj) ƒ
Procedure van de conformiteitsbeoordeling (geluid) ƒ Vastavushindamismenetlus (müra) ƒ
Vaatimustenmukaisuuden arviointimenettely (Melu) ƒ Procédure d’évaluation de conformité (bruit) ƒ
Konformitätsbeurteilungsverfahren (Geräusch) ƒ ǻȚĮįȚțĮıȓĮ ǹȟȚȠȜȩȖȘıȘȢ ȈȣȝȝȩȡijȦıȘȢ (ĬȩȡȣȕȠȢ) ƒ
MegfelelĘség-értékelési eljárás (Zaj) ƒ Procedura di valutazione della conformità (rumore) ƒ
AtbilstƯbas novƝrtƝjuma procednjra (troksnis) ƒ Atitikties Ƴvertinimo procednjra (garsas) ƒ
Proƛedura tal-Valutazzjoni tal-Konformità (ƪoss) ƒ Procedura oceny zgodnoĞci (poziom haãasu) ƒ
Processo de avaliação de conformidade (nível sonoro) Procedura de evaluare a conformităĠii (zgomot) ƒ
Postup vyhodnocovania zhodnosti (hluk) ƒ Postopek za ugotavljanje skladnosti (hrup) ƒ
Procedimiento de evaluación de conformidad (ruido) ƒ Procedur för bedömning av överensstämmelse (buller)
ƒ Samræmismatsaðferð (hávaði) ƒ Prosedyre for konformitetsvurdering (støy)
Not Applicable
UK Notified Body for 2000/14/EC ƒ ɇɨɬɢɮɢɰɢɪɚɧ ɨɪɝɚɧ ɜ Ɉɛɟɞɢɧɟɧɨɬɨ ɤɪɚɥɫɬɜɨ ɡɚ 2000/14/ȿɈ ƒ ÚĜad certifikovaný podle smČrnice þ. 2000/14/EC ƒ Det britiske
bemyndigede organ for 2001/14/EF ƒ Engels adviesorgaan voor 2000/14/EG ƒ Ühendkuningriigi teavitatud asutus direktiivi 2000/14/EÜ mõistes ƒ Direktiivin 2000/14/EY
mukainen ilmoitettu tarkastuslaitos Isossa-Britanniassa ƒ Organisme notifié concernant la directive 2000/14/CE ƒ Britische benannte Stelle für 2000/14/EG ƒ ȀȠȚȞȠʌȠȚȘȝȑȞȠȢ
ȅȡȖĮȞȚıȝȩȢ ǾȞȦȝȑȞȠȣ ǺĮıȚȜİȓȠȣ ȖȚĮ 2000/14/ǼȀ ƒ 2000/14/EK – egyesült királyságbeli bejelentett szervezet ƒ Organismo Notificato in GB per 2000/14/CE ƒ 2000/14/EK AK
reƧistrƝtƗ organizƗcija ƒ JK notifikuotosios Ƴstaigos 2000/14/EC ƒ Korp Notifikat tar-Renju Unit gƫal 2000/14/KE ƒ Dopuszczona jednostka badawcza w Wielkiej Brytanii wg
2000/14/WE ƒ Entidade notificada no Reino Unido para 2000/14/CE ƒ Organism notificat în Marea Britanie pentru 2000/14/CE ƒ Notifikovaný orgán Spojeného kráĐovstva pre
smernicu 2000/14/ES ƒ Britanski priglašeni organ za 2000/14/ES ƒ Cuerpo notificado en el Reino Unido para 2000/14/CE ƒ Anmält organ för 2000/14/EG i Storbritannien ƒ
Tilkynntur aðili í Bretlandi fyrir 2000/14/EC ƒ Britisk teknisk for 2000/14/EF
en-18
Number: 1088
Sound Research Laboratories Limited
Holbrook House, Little Waldingfield
Sudbury, Suffolk CO10 0TH
4
SPECIFICATIONS
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
Operator Ear Noise Level ƒ Ɉɩɟɪɚɬɨɪ ɧɚ ɧɢɜɨɬɨ ɧɚ ɞɨɥɨɜɢɦ ɨɬ ɭɯɨɬɨ ɲɭɦ ƒ
Hladina hluku v oblasti uší operátora ƒ Støjniveau i førers ørehøjde ƒ
Geluidsniveau oor bestuurder ƒ Müratase operaatori kõrvas ƒ
Melutaso käyttäjän korvan kohdalla ƒ Niveau de bruit à hauteur des oreilles de l’opérateur ƒ
Schallpegel am Bedienerohr ƒ ǼʌȓʌİįȠ șȠȡȪȕȠȣ ıİ ȜİȚIJȠȣȡȖȓĮ ƒ
A kezelĘ fülénél mért zajszint ƒ Livello di potenza sonora all’orecchio dell’operatore ƒ
TrokšƼa lƯmenis pie operatora auss ƒ Dirbanþiojo su mašina patiriamo triukšmo lygis ƒ
Livell tal-ƪoss fil-Widna tal-Operatur ƒ Dopuszczalny poziom haãasu dla operatora ƒ
Nível sonoro nos ouvidos do operador ƒ Nivelul zgomotului la urechea operatorului ƒ
Hladina hluku pôsobiaca na sluch operátora ƒ Raven hrupa pri ušesu upravljavca ƒ
Nivel sonoro en el oído del operador ƒ Ljudnivå vid förarens öra ƒ Hávaðastig fyrir stjórnanda ƒ Støynivå ved operatørens øre
Harmonised standards used ƒ ɂɡɩɨɥɡɜɚɧɢ ɯɚɪɦɨɧɢɡɢɪɚɧɢ ɫɬɚɧɞɚɪɬɢ ƒ Použité harmonizované normy ƒ Brugte harmoniserede standarder ƒ Gebruikte geharmoniseerde
standaards ƒ Kasutatud ühtlustatud standardid ƒ Käytetyt yhdenmukaistetut standardit ƒ Normes harmonisées utilisées ƒ Angewandte harmonisierte Normen ƒ ǼȞĮȡȝȠȞȚıȝȑȞĮ
ʌȡȩIJȣʌĮ ʌȠȣ ȤȡȘıȚȝȠʌȠȚȒșȘțĮȞ ƒ Harmonizált szabványok ƒ Standard armonizzati applicati ƒ Izmantotie saskaƼotie standarti ƒ Panaudoti suderinti standartai ƒ Standards
armonizzati uĪati ƒ Normy spójne powiązane ƒ Normas harmonizadas usadas ƒ Standardele armonizate utilizate ƒ Použité harmonizované normy ƒ Uporabljeni usklajeni standardi
ƒ Estándares armonizados utilizados ƒ Harmoniserade standarder som används
Technical standards and specifications used ƒ ɂɡɩɨɥɡɜɚɧɢ ɬɟɯɧɢɱɟɫɤɢ ɫɬɚɧɞɚɪɬɢ ɢ ɫɩɟɰɢɮɢɤɚɰɢɢ ƒ
Použité technické normy a specifikace ƒ Brugte tekniske standarder og specifikationer ƒ
Gebruikte technische standaards en specificaties ƒ Kasutatud tehnilised standardid ja spetsifikatsioonid ƒ
Käytetyt tekniset standardit ja eritelmät ƒ Spécifications et normes techniques utilisées ƒ
Angewandte technische Normen und Spezifikationen ƒ ȉİȤȞȚțȐ ʌȡȩIJȣʌĮ țĮȚ ʌȡȠįȚĮȖȡĮijȑȢ ʌȠȣ ȤȡȘıȚȝȠʌȠȚȒșȘțĮȞ ƒ MĦszaki szabványok és specifikációk ƒ Standard tecnici e
specifiche applicati ƒ
Izmantotie tehniskie standarti un specifikƗcijas ƒ Panaudoti techniniai standartai ir techninơ informacija ƒ
Standards u speƛifikazzjonijiet tekniƛi uĪati ƒ Normy i specyfikacje techniczne powiązane ƒ
Normas técnicas e especificações usadas ƒ Standardele tehnice úi specificaĠiile utilizate ƒ
Použité technické normy a špecifikácie ƒ Uporabljeni tehniþni standardi in specifikacije ƒ
Estándares y especificaciones técnicas utilizadas ƒ Tekniska standarder och specifikationer som används ƒ Samræmdir staðlar sem notaðir eru ƒ Benyttede harmoniserte
standarder
88 dB(A) Leq (2006/42/EC)
EN 836:1987
OECD Code 4 ROPS Static Test
The place and date of the declaration ƒ Ɇɹɫɬɨ ɢ ɞɚɬɚ ɧɚ ɞɟɤɥɚɪɚɰɢɹɬɚ ƒ Místo a datum prohlášení ƒ Sted og dato for erklæringen ƒ Plaats en datum van de verklaring ƒ
Deklaratsiooni väljastamise koht ja kuupäev ƒ Vakuutuksen paikka ja päivämäärä ƒ Lieu et date de la déclaration ƒ Ort und Datum der Erklärung ƒ ȉȩʌȠȢ țĮȚ ȘȝİȡȠȝȘȞȓĮ
įȒȜȦıȘȢ ƒ A nyilatkozat kelte (hely és idĘ) ƒ Luogo e data della dichiarazione ƒ DeklarƗcijas vieta un datums ƒ Deklaracijos vieta ir data ƒ Il-post u d-data tad-dikjarazzjoni ƒ
Miejsce i data wystawienia deklaracji ƒ Local e data da declaração ƒ Locul úi data declaraĠiei ƒ Miesto a dátum vyhlásenia ƒ Kraj in datum izjave ƒ Lugar y fecha de la declaración
ƒ Plats och datum för deklarationen ƒ Tæknistaðlar og tæknilýsingar sem notaðar eru ƒ Benyttede tekniske standarder og spesifikasjoner ƒ Staður og dagsetning yfirlýsingar ƒ
Sted og dato for erklæringen
Ransomes Jacobsen Limited
West Road, Ransomes Europark,
Ipswich, England, IP3 9TT
4th January 2010
Signature of the person empowered to draw up the declaration on behalf of the manufacturer, holds the technical documentation and is authorised to compile the technical file, and who is
established in the Community.
ɉɨɞɩɢɫ ɧɚ ɱɨɜɟɤɚ, ɭɩɴɥɧɨɦɨɳɟɧ ɞɚ ɫɴɫɬɚɜɢ ɞɟɤɥɚɪɚɰɢɹɬɚ ɨɬ ɢɦɟɬɨ ɧɚ ɩɪɨɢɡɜɨɞɢɬɟɥɹ, ɤɨɣɬɨ ɩɨɞɞɴɪɠɚɳ
ɬɟɯɧɢɱɟɫɤɚɬɚ ɞɨɤɭɦɟɧɬɚɰɢɹ ɢ ɟ ɨɬɨɪɢɡɢɪɚɧ ɞɚ ɢɡɝɨɬɜɢ ɬɟɯɧɢɱɟɫɤɢɹ ɮɚɣɥ ɢ ɟ ɪɟɝɢɫɬɪɢɪɚɧ ɜ ɨɛɳɧɨɫɬɬɚ.
Podpis osoby oprávnČné sestavit prohlášení jménem výrobce, držet technickou dokumentaci a osoby oprávnČné
sestavit technické soubory a založené v rámci Evropského spoleþenství.
Underskrift af personen, der har fuldmagt til at udarbejde erklæringen på vegne af producenten, der er indehaver
af dokumentationen og er bemyndiget til at udarbejde den tekniske journal, og som er baseret i nærområdet.
Handtekening van de persoon die bevoegd is de verklaring namens de fabrikant te tekenen, de technische
documentatie bewaart en bevoegd is om het technische bestand samen te stellen, en die is gevestigd in het Woongebied.
Ühenduse registrisse kantud isiku allkiri, kes on volitatud tootja nimel deklaratsiooni koostama, kes omab tehnilist
dokumentatsiooni ja kellel on õigus koostada tehniline toimik.
Sen henkilön allekirjoitus, jolla on valmistajan valtuutus vakuutuksen laadintaan, jolla on hallussaan tekniset
asiakirjat, joka on valtuutettu laatimaan tekniset asiakirjat ja joka on sijoittautunut yhteisöön.
Signature de la personne habilitée à rédiger la déclaration au nom du fabricant, à détenir la documentation
technique, à compiler les fichiers techniques et qui est implantée dans la Communauté.
Unterschrift der Person, die berechtigt ist, die Erklärung im Namen des Herstellers abzugeben, die die
technischen Unterlagen aufbewahrt und berechtigt ist, die technischen Unterlagen zusammenzustellen,
und die in der Gemeinschaft niedergelassen ist.
ȊʌȠȖȡĮijȒ ĮIJȩȝȠȣ İȟȠȣıȚȠįȠIJȘȝȑȞȠȣ ȖȚĮ IJȘȞ ıȪȞIJĮȟȘ IJȘȢ įȒȜȦıȘȢ İț ȝȑȡȠȣȢ IJȠȣ țĮIJĮıțİȣĮıIJȒ, Ƞ ȠʌȠȓȠȢ
țĮIJȑȤİȚ IJȘȞ IJİȤȞȚțȒ ȑțșİıȘ țĮȚ ȑȤİȚ IJȘȞ İȟȠȣıȚȠįȩIJȘıȘ ȞĮ IJĮȟȚȞȠȝȒıİȚ IJȠȞ IJİȤȞȚțȩ ijȐțİȜȠ țĮȚ Ƞ ȠʌȠȓȠȢ İȓȞĮȚ įȚȠȡȚıȝȑȞȠȢ ıIJȘȞ ȀȠȚȞȩIJȘIJĮ.
A gyártó nevében meghatalmazott személy, akinek jogában áll módosítania a nyilatkozatot, a mĦszaki
dokumentációt Ęrzi, engedéllyel rendelkezik a mĦszaki fájl összeállításához, és aki a közösségben letelepedett személy.
Firma della persona autorizzata a redigere la dichiarazione a nome del fabbricante, in possesso Della
documentazione tecnica ed autorizzata a costituire il fascicolo tecnico, che deve essere stabilita nella Comunità.
TƗs personas paraksts, kura ir pilnvarota deklarƗcijas sastƗdƯšanai ražotƗja vƗrdƗ, kurai ir tehniskƗ
dokumentƗcija, kura ir pilnvarota sagatavot tehnisko reƧistru un kura ir apstiprinƗta KopienƗ.
Asmuo, kuris yra gana žinomas, kuriam gamintojas suteikơ Ƴgaliojimus sudaryti šią deklaraciją, ir kuris ją
pasirašơ, turi visą techninĊ informaciją ir yra Ƴgaliotas sudaryti techninơs informacijos dokumentą.
Il-firma tal-persuna awtorizzata li tfassal id-dikjarazzjoni f’isem il-fabbrikant, gƫandha d-dokumentazzjoni
teknika u hija awtorizzata li tikkompila l-fajl tekniku u li hija stabbilita fil-Komunità.
Podpis osoby upowaĪnionej do sporządzenia deklaracji w imieniu producenta, przechowującej dokumentacjĊ
techniczną, upowaĪnioną do stworzenia dokumentacji technicznej oraz wyznaczonej ds. wspólnotowych.
Assinatura da pessoa com poderes para emitir a declaração em nome do fabricante, que possui a documentação
técnica, que está autorizada a compilar o processo técnico e que está estabelecida na Comunidade.
Semnătura persoanei împuternicite să elaboreze declaraĠia în numele producătorului, care deĠine documentaĠia
tehnică, este autorizată să compileze dosarul tehnic úi este stabilită în Comunitate.
Podpis osoby poverenej vystavením vyhlásenia v mene výrobcu, ktorá má technickú dokumentáciu a je
oprávnená spracovaĢ technické podklady a ktorá je umiestnená v Spoloþenstve.
Podpis osebe, pooblašþene za izdelavo izjave v imenu proizvajalca, ki ima tehniþno dokumentacijo in lahko
sestavlja spis tehniþne dokumentacije, ter ima sedež v Skupnosti.
Firma de la persona responsable de la declaración en nombre del fabricante, que posee la documentación técnica
y está autorizada para recopilar el archivo técnico y que está establecido en la Comunidad.
Undertecknas av den som bemyndigad att upprätta deklarationen å tillverkarens vägnar, innehar den tekniska
dokumentationen och är bemyndigad att sammanställa den tekniska informationen och som är etablerad i
gemenskapen. Undirskrift aðilans sem hefur umboð til að gera yfirlýsinguna fyrir hönd framleiðandans, hefur undir höndum
tæknigögnin og hefur leyfi til að taka saman tækniskýrsluna, og er viðurkenndur innan evrópska efnahagssvæðisins.
Signaturen til personen som har fullmakt til å utferdige erklæringen på vegne av produsenten, er i besittelse av den
tekniske dokumentasjonen, har autorisasjon til å utarbeide den tekniske filen og som har tilhold i EU.
Tim Lansdell
Technical Director
4th January 2010
Ransomes Jacobsen Limited
West Road, Ransomes Europark,
Ipswich, England, IP3 9TT
Certificate Number ƒ ɇɨɦɟɪ ɧɚ ɫɟɪɬɢɮɢɤɚɬ ƒ ýíslo osvČdþení ƒ Certifikatnummer ƒ Certificaatnummer ƒ Sertifikaadi number ƒ Hyväksyntänumero ƒ Numéro de certificat ƒ
Bescheinigungsnummer ƒ ǹȡȚșȝȩȢ ȆȚıIJȠʌȠȚȘIJȚțȠȪ ƒ Hitelesítési szám ƒ Numero del certificato ƒ SertifikƗta numurs ƒ Sertifikato numeris ƒ Numru taƛ-ƚertifikat ƒ Numer
certyfikatu ƒ Número do Certificado ƒ Număr certificat ƒ ýíslo osvedþenia ƒ Številka certifikata ƒ Número de certificado ƒ Certifikatsnummer ƒ Númer skírteinis ƒ Sertifikatnummer
4128577-r2
en-19
5
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
DECALS
5.1 SAFETY DECALS
A903491
Read Operator's Manual.
A903489
Keep a Safe Distance from the
Machine.
A903492
Stay Clear of Hot Surfaces.
A903488
Do Not Open or Remove Safety
Shields While the Engine is Running.
A903494
Caution Rotating Blades.
A903493
Avoid Fluid Escaping Under Pressure.
Consult Technical Manual for Service
Procedures.
A903490
Do Not Remove Safety Shields While
Engine is Running.
A911410
Danger of Explosion if the Battery
Terminals are Short Circuited.
A911416
Maximum permitable working slope.
A911434
Caution Diesel fuel.
5.2 INSTRUCTION DECALS
1 Speed Limiter Position
2 Centre Cutting Unit Latch
3 Bonnet latch Point
4 Hydraulic Oil Filter
5 Parking Brake On/Off
6 Horn
7 Hydraulic Oil Level
9 Traction Foot Pedal Control
10 Unit Ground Weight Adjustment
11 Throttle Lever
12
13
14
15
16
18
19
20
22
en-20
Tyre pressure
Cylinder Speed Adjustment
Cylinder Engage Foot Switch
Cylinder Engage Rocker Switch
Ignition Switch
Jacking Points
Hydraulic Oil Tank
Diesel Fuel Tank
Lift Points
6
CONTROLS
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
6.1 STARTER KEY SWITCH
The starter key (A) should be turned clockwise to
the 'pre-heat' (No. 2) position to heat the glowplugs
when the green warning lamp goes out on warning
lamp disply module turn the starter key clockwise to
the 'start' (No. 3) position to start the engine. After
starting, the key should be released and allowed to
return automatically to the 'on' (No. 1) position for
normal running. Where fitted the rotating beacon is
turned on when the key switch is in position No. 1
6.2 THROTTLE CONTROL LEVER
The lever (B) should be moved away from the
operator to increase the engine speed and towards
the operator to decrease the engine speed.
NOTE: Engine should be used at full speed.
6.3 STEERING WHEEL RAKE ADJUSTMENT
The steering wheel is adjustable for rake. The
clamping release knob (A) is situated on the side of
the control console on the right hand side. To adjust
turn the clamping knob anticlockwise to release and
pivot the steering wheel backwards and forwards to
obtain desired setting then lock in position by
turning clamping knob clockwise.
6.4 TRACTION FOOT PEDAL
To move the machine forward press the front of the foot
pedal (A). To reverse depress the rear of the foot pedal.
When the pedal is released it will return to its neutral
position.
6.5 SPEED LIMITER
The speed limiter (B) is operated by sliding the
black knob to the right or left. When slid to the right
the machine is limited to cutting speed, when slid to
the left, transport speed is available. In transport
mode, reverse is not available. When the speed
limiter is in the mow speed position four wheel drive
is engaged.
IMPORTANT: To enable mow engage the speed
limiter must be in the cutting speed position. If
cutting units are rotating, moving the speed
limiter between the mow and transport
positions will engage and disengage cylinder
rotation.
en-21
6
CONTROLS
6.6 TRANSPORT LATCHES
When transporting the machine ensure the cutting
units are raised and the transport latches (A) are
engaged.
6.7 PARKING BRAKES
The parking brake (B) is engaged when the lever is
moved toward the operator. The brake is fitted with a
micro switch that sensors brake position. The brake
must be applied to start the machine, and when
stopping and leaving the seat.
CAUTION:- The parking brake must not be applied
whilst the vehicle is moving.
6.8 HYDRAULIC LIFT LEVERS
The cutting units can be raised and lowered by
three control levers (A) situated on the right hand
side of the operators seat and can be operated as
follows:
Centre lever controls Rear Unit No. 1
Right hand lever controls R.H. Unit No. 2
Left hand lever controls L.H. Unit No. 3
NOTE: If any unit is raised out of work then lowered
into work again the cylinder will not rotate until the
mow foot switch is depressed.
To lift: Move the lever(s) upwards and hold in
position until the units are at the required height.
To lower: Move the lever(s) fully downwards and
release, the unit(s) will lower to ground level. DO
NOT hold lever in down position.
NOTE: The units will only lift and lower when the
engine is running.
IMPORTANT: If, when cutting, a lift control lever is
accidently pulled up, the cutting units will not float
over ground undulations until the lever is pushed
fully down and allowed to return to neutral again.
6.9 WEIGHT TRANSFER
Cutting unit ground pressure can be varied within
preset limits and is controlled by the handwheel (B)
on the right hand side of the operator's seat located
next to the lift/lower levers. The handwheel is turned
clockwise to reduce the groundweight of the cutting
unit, improving slope climbing ability.
The handwheel is turned anti clockwise to increase
the ground weight of the unit. Increased down
pressure will reduce the likelyhood of cutting unit
bounce when cutting undulating ground. When
cutting level ground the normal setting is midway
way between the maximum and minimum positions.
en-22
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
6
CONTROLS
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
6.10 CUTTING UNIT SWITCHES
To commence cutting ensure speed limiter is in
mow position and the cylinders have been lowered
Push bottom of the rocker switch (A) and depress
foot switch (B) Push top of rocker switch to stop
cutter unit rotation. (Cutting units stop rotating
automatically when raised.)
NOTE: The backlapping lever must be in the drive
position before cylinders wil rotate.
6.11 VARIABLE CYLINDER SPEED
The speed of rotation of the cutting cylinders is
adjustable by means of the handwheel (A) situated
on the left hand side of the operator. Cylinder speed
should be set to maximum in normal cutting
conditions. In very long growth conditions, cylinder
speed should be reduced to obtain best
finish,cylinder speed should also be reduced when
cutting very short, dry grass to prevent excesive
cylinder and bottom blade wear. Rotate the hand
wheel clockwise to increase cylinder speed,
anticlockwise to decrease cylinder speed.
6.12 BACKLAPPING LEVER
The lever (B) sets cutting cylinder rotational
direction with three positions:
(a) fully towards the seat for mowing, (b) fully away
from the seat for backlapping and (c) set in the mid
position for neutral. See the separate cutting unit
operator's manual for an explanation of the
backlapping procedure.
en-23
6
CONTROLS
6.13 INSTRUMENT PANEL
A.
ENGINE PREHEAT INDICATOR LAMP
Colour green, on when the ignition switch is turned
clockwise to the pre-heat position. Once the lamp
goes out the engine can be started.
B.
ENGINE TEMPARATURE GUAGE
Indicates current temparature of engine, whilst
running.
C.
ENGINE OVERHEAT WARNING LAMP
Colour red, on when the engine temperature reaches
a preset level. If the lamp comes on and a warning
horn is sounded bring to machine to a stop,
disengage the cutting cylinders, apply the parking
brake and allow the engine to cool by running the
engine at half speed for two minutes before stopping
and investigating the cause.
D.
CHARGING WARNING LAMP
Colour red, on when ignition is switched on and will go
out when the engine is started. If the light comes on while
the engine is running, the fan belt may be slipping or
broken or a fault in the electrical system is indicated and
should be investigated. STOP IMMEDIATELY.
E.
ENGINE OIL PRESSURE WARNING LAMP
Colour red, on when the ignition is switched on, and will
go out once the engine has started. If the light comes on
while the engine is running - STOP IMMEDIATELY as
this indicates that the engine oil pressure is too low.
Check the level of oil in the sump and top up as
necessary. Check the oil pressure sender switch.
Continued operation may cause extensive damage to the
engine.
F.
4 WHEEL DRIVE IN REVERSE SWITCH
Press and hold the bottom half of the switch to
engage 4 wheel drive when reversing. (Where
fitted). This function only operates when in cutting
mode.
G.
HEAD LIGHT/SIDE LIGHT
Depress the bottom half of the switch to turn on the
headlights and sidelights. (Where fitted)
H.
DIRECTIONAL INDICATORS
Depress left hand-side of switch to signal left, and
right hand-side of switch to signal right. (Where
fitted)
I.
HAZARD WARNING LIGHTS.
Press the top half of the switch to turn on the hazard
warning lights. (Where fitted)
en-24
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
6
CONTROLS
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
J.
BLOCKED HYDRAULIC FILTER
INDICATOR.
Monitors Hyd filter condition. Colured red,
Illuminates prior to filter bypass valve operating,
when illuminated filter requires changing. The lamp
should illuminated while the engine is preheating as
a test. It is not unusual for the lamp to stay light for
up to 3 minutes after a very cold start. But should
not stay on for longer than 5 minutes.
K.
HOURMETER
Located on the lefthand side of the steering tower,
above the parking brake . Records engine running
hours.
L.
FUEL GUAGE
Located to the left of the engine temparature guage.
Monitors fuel level.
M.
HORN
Press button to sound horn.
6.14 DIFF LOCK CONTROL
The Diff lock (A) is operated by depressing the foot
switch. When the foot switch is released the Diff
Lock ceases to operate. The Diff Lock should only
be used in severe situations, and should never be
used on tarmac or whilst steering
en-25
7
OPERATION
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
7.1 DAILY INSPECTION
CAUTION
The daily inspection should be performed
only when the engine is off and all fluids are
cold. Lower implements to the ground,
engage parking brake, stop engine and
remove ignition key.
1.
Perform a visual inspection of the entire unit, look for signs of wear, loss hardwear and missing or
damaged components. Check for fuel and oil leaks to ensure connections are tight and hoses and
tubes are in good condition.
2.
Check the fuel supply, radiator coolant level, crankcase oil level and air cleaner indicator. All fluids
must be at the full mark with the engine cold.
3.
Make sure all cutting units are adjusted to the same height of cut.
4.
Check all tyres for proper inflation.
5.
Test the operator presence and safety interlock system.
en-26
7
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
OPERATION
7.2 OPERATOR PRESENCE AND SAFETY INTERLOCK SYSTEM
1.
The operator presence & safety interlock system prevents the engine from starting unless the parking
brake is engaged, the mowing device is off and the operator is not in the seat. The system also
stops the engine if the operator leaves the seat with the mowing device engaged or the traction pedal
out of neutral.
WARNING
Never operate the equipment with the
operator presence & safety interlock
system disengaged or malfunctioning. Do
not disconnect or bypass any switch.
2.
Perform each of the following tests to ensure the operator presence & safety interlock system is
functioning properly. Stop the test and have the system inspected and repaired if any of the tests
fail as listed below:
•
•
•
The engine does start in test 1;
The engine does not start during tests 2,3 or 4;
The engine continues to run during test 5.
3.
Refer to the chart below for each test and follow the check (ü) marks across the chart. Shut engine
off betwen each test.
Test1:
Represents normal starting procedure. The operator is seated, parking brake is
engaged, the operators feet are off the pedals and the mower engagement device is off.The engine
should start.
Test 2:
The engine must not start if the mower engage device is on.
Test 3:
The engine must not start if the operator is not seated.
Test 4:
The engine must not start if the traction pedal is depressed.
Test 5:
Start the engine in the normal manner, push speed governor into Cut position, engage
mower switch on dash, engage cutting cylinders by depressing foot switch and lift your
weight off the seat.
Test
Operator
Seated
Yes
No
Parking
B rake
Applied
Yes
1
9
9
2
9
9
9
3
4
9
5
9
No
Mow Engage
Sw itch
C ut
9
9
D isE n g ag ed
Yes
9
9
9
9
’
Engine
Starts
9
No
9
9
9
9
9
’
’ Li ft your wei ght off seat. The cutti ng uni ts must stop rotati ng wi thi n seven (7)
seconds
en-27
7
OPERATION
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
7.3 OPERATING PROCEDURE
CAUTION
To help prevent injury, always wear safety
glasses, leather work shoes or boots, a
hard hat and ear protection.
1.
Under no circumstances should the engine be started without the operator seated on the tractor.
2.
Do not operate tractor or attachments with loose, damaged or missing components. Whenever
possible mow when grass is dry
3.
First mow in a test area to become thoroughly familiar with the operation of the tractor and control
levers.
Note:
To prevent damage to the reel and bottom blade never operate the reels when they are not
cutting grass. Excessive friction and heat will develop between the bottom blade and reel and
damage the cutting edge.
4.
Study the area to determine the best and safest operating procedure. Consider the height of the
grass, type of terrain, and condition of the surface. Each condition will require certain adjustments
or precautions.
5.
Never direct discharge of material toward bystanders, nor allow anyone near the machine while in
operation. The owner/operator is responsible for injuries inflicted to bystanders and/or damage to
their property.
CAUTION
Pick up all debris you can find before
mowing. Enter a new area cautiously
Always operate at speeds that allow you to
have complete control of the tractor
6.
Use discretion when mowing near gravel areas (roadway, parking areas, cart paths, etc.). Stones
discharged from the implement may cause serious injuries to bystanders and/or damage the
equipment.
7.
Disengage the drive motors and raise the implements when crossing paths or roads. Look out for
traffic.
8.
Stop and inspect the equipment for damage immediately after striking an obstruction or if the
machine begins to vibrate abnormally. Have the equipment repaired before resuming operation.
WARNING
Before you clean, adjust, or repair this
equipment, always disengage all drives,
lower implements to the ground, engage
parking brake, stop engine and remove key
from ignition switch to prevent injuries.
en-28
7
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
OPERATION
WARNING
DO NOT USE ON SLOPES GREATER THAN 15°
9.
Slow down and use extra care on hillsides. Read Section 3.7. Use caution when operating near drop
off points.
10.
Never use your hands to clean cutting units. Use a brush to remove grass clippings from blades.
Blades are extremely sharp and can cause serious injuries
OPERATION OF THE MACHINE
Read the Safety Instructions.
BEFORE OPERATING FOR THE FIRST TIME
•
•
•
•
•
•
Check and adjust tyre pressure, if
necessary, to 1 kg/cm2.
Add diesel fuel to tank if neccesary.
Add LPG if neccesary, see self-Serve
Instructions below.
Check engine oil and top-up, if
necessary.
Check radiator coolant and top-up, if
necessary (50% antifreeze solution).
Make sure you understand the information
contained in the preceeding General
Instructions and Instruments & Controls
sections.
NOTES:
•
Warm engine - When the engine is warm
because of surrounding temperature or
recent operation, step No.2 of the cold
engine starting procedure may be skipped
(no need to preheat glow plugs).
•
If the engine fails to start after two tries
(with preheat if necessary), wait 20
seconds and try again.
•
The starter motor should never be run
continuously for longer than 30 seconds or
it may fail.
7.5 DRIVING
•
•
•
7.4 STARTING THE ENGINE
•
The following procedure is for starting cold engines.
1.
Ensure the FWD/RVS pedal is in the
neutral position, the speed limiter is in the
transport position, the mow switch off, the
throttle setting is in a mid position and the
parking brake is applied.
2.
Turn the ignition switch to position No.2
and hold until the glow plug light goes off
(5-10 sec.)
3.
Turn ignition key fully clockwise to the
start position and operate the starter motor
until the engine starts (This should only
take a few seconds)
4.
When the engine starts, release the key
immediately and it will return to the RUN
position.
5.
If the engine does not start, preheat the
glow plugs and try again.
Release brake - Make sure the parking
brake is released before attempting to go
forward or reverse.
Forward - Gently depress the top plate of
the FWD/RVS foot pedal to reach desired
ground speed.
Reverse - Gently depress the bottom plate
of the FWD/RVS foot pedal to reach
desired ground speed. Engage 4 wheel
drive if required, where fitted.
To stop - Gently return the FWD/RVS foot
pedal to the neutral position.
NOTES:
•
Use complete foot to operate both forward
and reverse.
•
Do not move pedal suddenly–always
operate slowly and smoothly. Never move
pedal violently from forward to reverse or
vice versa.
•
Always keep foot firmly on the foot pedal–a
too relaxed foot control may result in a jerky
motion.
en-29
7
OPERATION
7.6 MOWING
1.
2.
3.
3.
NOTE:
Lower the reels with the cutting unit lift
control.
Ensure speed limiter is in mow position
Engage the cutting mechanism by pushing
on the lower half of cutting unit switch and
operating the floor mounted switch.
Release the parking brake and begin
driving forward.
Always set the throttle to full for mowing,
even when the grass is heavy. When the
engine is labouring, reduce forward speed
by easing up on the FWD/RVS foot pedal.
Four wheel drive will only operate with the
speed limiter in the mow position.
7.7 TO STOP THE ENGINE
1.
2.
3.
3.
4.
Disengage power to the cutting units with
the cutting unit switch.
Remove foot from the FWD/REV pedal.
Set the parking brake.
Move the throttle control lever to the
SLOW position.
Turn the ignition key to OFF.
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
WARNING
Cutting Unit Transport Latches are a
Secondary Safety Devise.
When Transporting the machine the
Cutting units should be held in the
Transport position on the Hydraulics with
the Transport Latches Engaged.
1. Park the machine on level ground.
2. Whilst seated in the driving position
With the engine at operating speed
raise the cutting units fully by
operating lift levers, return the lever to
the neutral position.
DO NOT move the lever into the
lower position.
3. Disengage drives, stop the engine and
make sure all moving parts are
stationary. Apply brakes and remove
the starter key.
4. Transport latches can now be engaged
or released.
Before releasing transport latches
it is important that all cutting units
are fully raised.
en-30
7
OPERATION
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
7.8 PUSHING THE MACHINE WITH THE ENGINE
STOPPED
1. To push, disengage the parking brake.
2. Turn screw (A) located on the underside of the
transmission pump 1 turn counterclockwise. Set
the steering wheel so that the rear wheels are
pointing straight ahead.
3. Remove the tower cover and turn the
emergengy brake valve( B) towards the parking
brake/hour meter side of the tower.
4. Turn the steering wheel to the left until resistance can be detected. The machine is now
ready to push. If unable to move the machine
apply further pressure to the steering wheel.
Excessive force should never be used on
the steering wheel.If the rear wheels start to
turn too much force is being applied.
5. After pushing, return valve (B) and knob (A) to
their previous positions.
en-31
7
OPERATION
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
7.12 MOWING ON SLOPES
The mower has been designed for good traction and stability under normal mowing conditions. Use caution
when operating on slopes, especially when the grass is wet. Wet grass reduces traction and steering
control.WARNING
WARNING
To minimize the possibility of overturning,
the safest method for operating on hills and
terraces is to travel up and down the face of
the slope (vertically), not across the face
(horizontally). Avoid unnecessary turns,
travel at reduced speeds, and stay alert for
hidden hazards.
A = Maximum Allowable Slope
1.
Always mow with the engine at full throttle,
control forward speed using traction foot
pedal to maintain proper cutting.
2.
Use weight transfer control as required to
improve weight distribution between decks
and mower.
3.
If the mower tends to slide or the tyres begin
to mark the turf, angle mower into a less
steep slope until traction is regained or tyre
marking stops.
4.
If mower continues to slide or mark the turf,
the slope is too steep for safe operation. Do
not make another attempt to climb, and back
down slowly.
5.
When descending a steep slope, always
lower implements to the ground to reduce the
risk of mower overturning.
A = Maximum Allowable Slope
Correct tyre pressure is essential for maximum
traction.
Degrees are shown to the nearest 1/4”.
See Specification
WARNING
DO NOT USE ON SLOPES GREATER THAN 15°
en-32
General slope of roadway embankment - 45°
Steepest grass area - 31°
Slope of average roof - 19-1/4°
2nd class highway maximum grade 4-1/2°
Toll road or freeway - 1-3/4°
7
OPERATION
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
If it is necessary to mow across a short slope,
ensure the right hand cutting unit is the lowest.
WARNING
When the machine is being used, whether
cutting grass or not, on slopes, the ROPS
frame should be deployed and the seat belt
used.
This rationale is based on the fact that a seat
belt must be worn with a ROPS to comply
with the Machiney Directive 2006/42/EC
sections 3.2.2, Seating & 3.4.3, Rollover
A = Maximum Allowable Slope
Ransomes Jacobsen Limited recommends
that a local risk assessment is completed by
the owner/user of the machine to determine
the risks associated with working on slopes.
How to calculate a slope
Tools:
Spirt level 1 metre long.
Tape measure.
With the spirt level (A) positioned horizontally measure the distance (C) with tape measure (B) Use the chart
to calculate either the slope angle or the% grade D of the slope.
en-33
7
OPERATION
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
Use Either of these columns but not both
Height C in millimeters
Height C in inches
measured with a 1
measured with a 1 yard
metre horizontal edge
horizontal edge A
A
3
100
5.7
10.0
150
8.5
15.0
9.5
16.7
11.3
20.0
11.8
20.8
225
12.7
22.5
250
14.0
25.0
275
15.4
27.5
15.5
27.8
16.7
30.0
17.0
30.6
18.0
32.5
18.4
33.3
19.3
35.0
19.9
36.1
20.6
37.5
21.3
38.9
21.8
40.0
22.6
41.7
23.0
42.5
24.0
44.4
475
25.4
47.5
500
26.6
50.0
29.1
55.6
31.0
60.0
34.8
69.4
38.7
80.0
39.8
83.3
900
42.0
90.0
1000
45.0
100.0
7.5
10
300
11
325
12
350
13
375
14
400
15
425
16
20
600
25
800
30
36
en-34
Slope Angle D
measured in Grade%
8.3
200
18
Slope Angle D
measured in Degrees
4.8
6
9
The result of what you are measuring
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
en-35
8
LUBRICATION AND MAINTENANCE
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
8.1 LUBRICATION AND MAINTENANCE CHART
MAINT ENANCE AND LUBRICAT ION CHART
Interval
First 50
hours
Item
Section
z Change Engine Oil
z Change Engine Oil Filter
z
z
z
z
z
z
z
z
8.4
Check Engine Oil Level
Check / Clean Air Filter Element
Check / Clean Bug Screen / Radiator
Check Coolant Level
Check Hydraulic Fluid Level
Check Tyre Pressure
Check Engine Bay for Debris
Check Foot Pedal For Free Movement
8.2
8.2
8.2
8.2
8.2
Weekly 40
hours
z Check Battery Condition
z Check Hydraulic Fittiings for T ightness
z Check Nuts & Bolts for T ightness
8.9
Every 100
hours
z Check & Clean Air Filter Element *
z Check Fuel Filter For Water Contamination
8.7
8.8
Every 200
hours
z Change Engine Oil & Oil Filter
8.4
Every 400
hours
z Change Air Filter Element *
z Replace Inline Fuel Filters
z Replace Fuel Filter Cannister
8.7
z Change Hydraulic Oil & Filters
z Drain & Replace Engine Coolant
8.10
8.10
Daily 10
hours
End of
Season
or
1000 hours
8.8
Lubricate all Grease fittings with K NAT E (RJL No. 4213860) or equivilent Grease Weekly
* Check more often in dirty conditions
IMPORTANT
Refer to Engine Manufacturers Manual for Additional Engine Maintenance Procedures
FLUID REQUIREMENT S
en-36
QUANT IT Y
T YPE
A
ENGINE OIL
(with filter)
6.4 Litres
10W 30
B
HYDRAULIC OIL
(with filter)
35 Litres
ISO VG46 or
Equivilant
C
RADIAT OR
COOLANT
5 Litres
50% ANTIFREEZE
D
FUEL
45 Litres
No 2-D
(ASTMD975)
Diesel
8
LUBRICATION AND MAINTENANCE
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
8.2 DAILY CHECKS (Every 8 working hours)
Oil Level.
Check level of oil in sump. Remove dipstick (A) wipe
and replace and check that oil is up to the
maximum mark. Top up with SAE30 if neccesary. It
is important that this test is carried out with the
engine cold and vehicle parked on level ground.
Air Filter.
Examine blockage indicator (B) If indicator shows
red filter element requires cleaning or replacement.
The indicator is reset bt pressing the button on the
end of the indicator.
Hydraulic Oil Level.
Check hydraulic oil level in tank. The level of oil
should be maintained so it is just visible in the sight
tube (C) Top up with Tellus 46 or equivilant if
neccesary. The oil level should be checked cold
with the machine parked on level ground.
IMPORTANT:
Absolute cleanliness must be observed when
filling the hydraulic tank. Oil must be filtered
through a 25 micron filter before entering the
hydraulic tank.
Cooling System.
Check coolant level in expansion tank (D) The
coolant level should be between the marks indicated
on the bottle. Top up if neccesary using a 50%
antifreeze solution.
NOTE:
To avoid the risk of accidental injury
the seat plate and bonnet are fitted
with locks. These should be kept
secure when access is not required.
Cleaning the air filter
Remove loose dirt from element with compressed air
working from the "clean" to "dirty" side.
Note:
Compressed air must not exceed 6bar,
with the nozzle 50mm away from element.
The element should be replaced after 6
cleanings.
Cooling System.
Check Bug Screen (E) is free from dust and
there is an un-interupted air flow to engine. The
screen should be fitted with the mesh facing the
rear of the machine. Any deris should be removed
with a soft hand brush.
en-37
8
LUBRICATION AND MAINTENANCE
8.3
MACHINE: Every 400 Working Hours.
Lubrication of Direct Drive Hydraulic Motor (Every 400
hours)
Lower all cutting units onto level ground. Before leaving
the driving position, stop the engine and make sure all
moving parts are stationary. Apply brakes and
disengage all drives. remove the starter key. The direct
8.4
MACHINE: Every 800 Working Hours.
Change Hydraulic Oil.
1.
Remove drain plug in bottom of Hydraulic
tank and wipe off plug.
2.
Allow tank to drain and replace plug.
3.
Refill tank with ISO VG 46 Oil.
IMPORTANT
Absolute cleanliness must be observed when filling
the hydraulic tank. Oil must be filtered through a 25
micron filter before entering the hydraulic tank.
8.5
HYDRAULIC TEST POINTS.
There are 5 test points available on the machine for
conducting hydraulic system checks.
•
Forward drive pressure (A)
•
Reverse drive pressure (B)
•
Charge pressure (C)
•
Cutting cylinder drive pressure (D)
•
Lift and power steering pressure (E)
en-38
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
drive hydraulic motor can be removed from the
cutting unit by removing the two screws and washers
holding the motor to the bearing housing. Carefully
withdraw the motor from the bearing housing, it is
important not to contaminate the motor shaft or
internal splines of the cutting cylinder. If for any
reason they are contaminated, they should be
cleaned by degreasing. Liberally lubricate the motor
and cylinder splines with Shell Malleus JB1 grease
before reassembling.
8
LUBRICATION AND MAINTENANCE
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
8.6 ENGINE MAINTENANCE - DIESEL
Every 100 hrs
Fuel System.
Use Diesel fuel No.2-D (ASTM D975)
See engine manufacturer's manual for additional
information.
Water Separator - If water is not removed from the
fuel, extensive damage can be done to the fuel
injection system.
1.
2.
3.
With engine off, open vent (A) at top of
water separator.
Open drain valve (B) at bottom of water
seperator to allow any water to drain out.
If water is present, it will drain first. When
fuel emerges from the valve (B), close the
valve. Close the vent (A).
NOTE: Failure to drain water reduces fuel filter
efficiency.
Bleeding air from fuel system
1.
2.
3.
4.
Turn the ignition switch to the ON position
(don't start engine).
Open air vent (C) on side of injection pump
to allow air to escape.
Retighten air vent.
Turn ignition to OFF.
en-39
8
LUBRICATION AND MAINTENANCE
8.7 ENGINE MAINTENANCE - DIESEL
Every 400 hrs
Replace In-line fuel (C)
Cleaning the air filter
Remove loose dirt from element with compressed air
working from the clean to dirty side, using
compressed air max 6 bar , with nozzle 5cm from
element.
Change air filter (Or every 6 cleanings)
1.
Raise bonnet.
2.
Remove end cap of air filter cartridge.
3.
Remove accumulated dust or dirt.
4.
Remove filter element (B) (pull straight out
firmly)
5.
install new filter element (press firmly
against rear shoulder)
6.
Replace end cap and fasten with clips
NOTE: Extensive damage to engine can result from
an inadequate air supply.
en-40
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
8
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
LUBRICATION AND MAINTENANCE
8.8 ENGINE MAINTENANCE - DIESEL
Every 400 hrs
Changing fuel filter
1.
Unscrew filter (A) from filter head.
2.
Remove water (B) separator from filter and
discard filter.
3.
Fit water separator to new filter and refit
filter to head.
4.
Bleed air from system as describe in section
5.6.
8.9
MACHINE MAINTENANCE
Battery.
Keep fluid levels above battery plates.
Storage
•
Store petrol or diesel fuel in an approved
container in a cool dry place.
•
Keep the machine and fuel containers in a
locked storage place to prevent tampering
and to keep children from playing with
them.
•
Do not store fuel or petrol/diesel fuel
powered equipment in any closed area
where heating appliances, pilot lights or any
sort of open flame is present.
•
Before storing, allow the engine to cool,
and drain fuel completely from fuel tanks
and containers.
•
Maximum safety and best mowing results
can only be expected if the mower is
maintained and operated properly.
WARNING
Wear eye protection when servicing battery.
WARNING
Battery posts, terminals and related
accessories contain lead and lead
compounds
WASH HANDS AFTER HANDLING
Other Regular Service.
•
Verify proper operation of safety interlock
switches (Parking Brake, Seat switch,
etc.)
•
Ensure nuts and bolts remain tight.
•
Keep tyre pressure at 1kg/cm2 (14psi).
•
Follow the engine manufacturer’s
maintenance recommendations.
•
If a label becomes worn or removed, see
the LABELS section of this manual or the
tractor Parts Manual for replacement
information.
NOTE: When washing machine with pressure spray
washers or steam cleaners, avoid washing bearing areas
because cleaning solutions might penetrate bearing seals
and cause premature bearing failure.
en-41
8
LUBRICATION AND MAINTENANCE
8.10 END OF SEASON or when required
Change Hydraulic filter.
1.
Lower the centre cutting unit to improve
access.
2.
Wipe filter bowl (A) and housing to remove
any dirt present.
3.
Place a suitable drip tray on top of the centre
cutting unit.
4.
Unscrew bowl and remove oil filter element
and disposes of safely.
5.
Replace with new element.
6.
Coat the top outside lip of the filter bowl with
a thin film of oil and refit filter bowl and
torque to 54Nm, as indicated on decal.
7.
Start engine and idle for 15 seconds.
8.
Stop engine, check filter bowl for leaks and
check reservoir
NOTE:
It is important that absolute cleanliness
is observed when changing the filter.
Change Coolant.
1.
Completely drain the cooling water from the
radiator drain plug (B) and flush the cooling
system with flushing detergent.
2.
Check for leaks or loose connections at the
radiator, cylinder head gasket, drain cock etc.
3.
Mix antifreeze coolant and water at the
specified ratio before pouring into the engine.
Note: When topping up the cooling system fill with a
50/50 solution.
Check Rear Wheel Bearings. (2WD Only)
1.
Jack up, and securely chock the rear of the
machine using points indicatored in
section 5.2
2.
Check for free-play in bearings,
3.
If free-play is found remove dust cover and
split pin and tighten castlated nut till all free-play is
eliminated.
Transmission Foot Pedal & Cable
Inspect the cable for damage and freedom of
movement. Fully cycle the cable to check that the
inner element is in good condition. Inspect the outer
sheath for damage and alignment. Correct or
replace as appropriate
en-42
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
9
ADJUSTMENTS
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
9.1 SPEED LIMITER.
The transport and mow speeds of the machine are
factory set and should not be altered. Ransomes
Jacobsen Limited cannot be held responsible for
loss of performance or machine damage if these
speeds are altered.
9.2
ALTERNATOR/WATER PUMP - DIESEL
The water pump belt is adjusted so that it has
sufficient tension to avoid undue stress on alternator
bearings but does not slip on the alternator pulley.
Use the following procedure to check the belt
tension at the mid-point of the belt between crank
shaft and alternator pulleys.
1. Loosen alternator bolt (Diesel A / LPG 1 & 2)
and pivot bolt on the underside of the Alternator.
2. Move the alternator to tighten or loosen the belt
so that a deflection of 7 to 9 mm is achieved at
the mid-span with a load 10Kgf (98N/22lbs) for
a new belt, and 8 to 10mm for a used belt.
3. Re-tighten bolts .
9.3
COOLING FAN BELT - DIESEL
The cooling fan belt is adjusted so that it has some
slack to avoid undue stress on the water pump
bearing but does not slip on the pulley. Use the
following procedure to check the belt tension in the
span between the fan and tension pulleys.
1. Loosen tensioner bolt (C)
2. Release lock nut on bolt (B)
3. Adjust bolt (B) to obtain a belt deflection of 10 to
11mm with a load 10Kgf (98N/22lbs) for a new
belt, and 11 to 11.5mm for a used belt.
4. Re-tighten bolt (C)
en-43
9
ADJUSTMENTS
9.4 HEIGHT OF CUT
The height of cut can be set between:
13mm (1/2in) and 51mm (2in) (61mm on the spanner
adjust) on the Magna 250 fixed head.
13mm (1/2in) and 35mm (1 3/8in) on the Sport 200
floating head standard blade.
TO ADJUST HAND WHEEL TYPE:
1. Turn the adjuster handwheel (A) clockwise to
increase the height of cut, or anticlockwise to decrease
the height of cut.
2. Ensure that an equal amount of adjustment is made
to both adjusters on all the cutting units. To assist in
obtaining equal adjustment height of cut indicators (B)
are provided at each end of the roll assembly.
NOTE: The numbers 1 to 9 are only for reference from
one side of the roll to the other and bear no relation to
the height of cut other than each graduation gives
approximately 6.25mm (1/4in) height of cut movement
for fixed head units and 3.75mm (5/32in) for floating
head units. These indicators are set at the factory and
when the pointer is set the same at each end of the roll
the roll will be parallel with the bottom blade. If due to
any reason the roll and bottom blade are not parallel with
each other the roll can be set parallel with the bottom
blade by rotating one of the handwheels and then one
indicator adjusted by slackening the small clamping
screw in the centre of the indicator plate and positioning
the indicator relative to the pointer at the opposite end
of the roll assembly.
3. No other adjustments are necessary.
4. THIS IS A SELF LOCKING MECHANISM THERE
BEING NO NECESSITY TO UNLOCK OR LOCK THE
MECHANISM.
TO ADJUST SPANNER TYPE:
1)
Release the two screws (C) which hold the
eccentric bush in the lever.
2)
Turn the adjuster (B) at the rear of the unit,
clockwise to reduce the height of cut, or
anticlockwise to increase the height of cut.
3)
After adjustment tighten screws
(C) to a maximum torque of 17Nm.
en-44
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
9
9.5
ADJUSTMENTS
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
BACKLAPPING
Ransomes Jacobsen grinding paste:
This mower is fitted with a device to allow the reels
to be driven in reverse for backlapping.
•
•
Backlapping is a process which will lightly
grind the reel to the bedknife whilst
mounted on the mower.
If significant amounts of metal are to be
removed then the cutting unit should be
reground on a specialised grinding
machine.
•
Before any backlapping is carried out,
Ransomes Jacobsen recommends that the
backlapping process should be risk
assessed as a workshop process by the
manager of the machine.
•
Backlapping should only be carried out by
trained staff.
•
Ransomes Jacobsen recommend that
grinding paste is only applied to the reel
when it is stationery, the engine is off and
the parking brake applied.
•
When applying grinding paste the reel
should only be rotated by appropriately
sized piece of wood and not by hand.
•
Place reels in the most accessible position
for applying the paste.
•
Leave the grass boxes in position on the
cutting units as a safety barrier.
•
After applying the grinding paste the
person backlapping should return to the
seat, engage the relevant controls and run
the reels in reverse.
•
When the desired finish is achieved
switch off the mower, clean off any
surplus paste, reset the reel to bedknife
and return the controls to the normal mow
positions.
80 grit grinding paste, 4.5kg tin,
Part number 5002488
120 grit grinding paste, 4.5kg tin,
Part number 5002489
80 grit grinding paste, 9kg tin,
Part number 5002490
120 grit grinding paste, 9kg tin,
Part number 5002491
en-45
9
ADJUSTMENTS
9.6
GENERAL INSTRUCTIONS FOR
GRAMMER SEATS
Adjustments must not be made while driving.
•
•
After removal of the backrest upholstery,
the backrest frame must be supported, for
example held in place,
before the backrest adjuster is operated. If
you fail to do so, there is a danger that the
backrest frame may jerk forward and
cause injury.
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
•
•
•
•
•
•
Any changes to the series standard of the
seat (for example fitting parts which are
not original GRAMMER parts) may impair
the safety standard to which it has been
tested.
Functions may be impaired, threatening
your safety. For this reason, any changes
in design of the seat must be approved by
GRAMMER.
•
•
During the removal and installation of the driver’s
seat, the corresponding instructions by
the specific vehicle manufacturer must be strictly
observed!
•
•
•
•
•
•
•
•
•
en-46
Do not hold onto the covers for lifting the
driver’s seats. If you do so anyway, there
is an increased risk of injury due to
loosening or breaking covers.
Before you remove the driver’s seat,
disconnect all plug-in connections between
the seat and the vehicle supply network.
When you replace the plug-in connectors,
make sure they are tight to avoid ingress
of dust and water.
Seatbelts can be retrofitted to the driver’s
seat. Seatbelts may only be fitted on the
approval of the vehicle manufacturer, as
they increase the load in the seat mounting
area.
Seatbelts must be fitted in accordance with
specific national regulations and
guidelines, and must be approved by
GRAMMER.
Retrofitted seatbelts must be fastened
before driving.
The seat belt must be replaced after an
accident.
Where seatbelts are fitted to the driver’s
seat, the seat and seat mounting must be
checked additionally by specialist
personnel after an accident has occurred.
•
•
•
•
Fasteners must be,
checked regularly
for tight seat. If the seat wobbles there
may be loose bolts or other faults.
If you notice that the seat does not
function correctly (for example a defective
seat suspension; improper curvature of
the lumbar support or damaged bellows),
contact a specialist workshop immediately
to arrange for repairs to be carried out.
If you fail to do so, your health may be
affected and the risk of accident
increased.
Before the vehicle is used, switches that
might be in the seat (for shutting down
mechanical equipment when the driver
leaves his/her seat) must be checked for
proper function
If malfunctions are detected, the vehicle
must not be driven. – INCREASED RISK
OF ACCIDENT –
Loads must not be placed on seats with a
built in switch, except for the driver’s
weight during normal use, as the vehicle
may otherwise start to move by itself. –
INCREASED RISK OF ACCIDENT –
If you take off the weight from the seat
while driving, this will cause the vehicle to
stop.
Do not indent the bellows while there is
load on the driver’s seat. – RISK OF
CRUSHING –
Make sure that the interior of drivers seat
remains free of foreign particles or liquids.
The driver’s seat is not watertight and must
be protected against splashes of water!
Any conversion or refitting work on a
GRAMMER driver’s seat must be
performed exclusively in authorised
workshops by trained or suitably qualified
personnel and in adherence with the
applicable operating, maintenance and
installation instructions and in compliance
with all relevant national regulations.
Improper installation and assembly bear
the risk of personal injury or property
damage and the proper function of the
driver’s seat or mounted parts can no
longer be guaranteed.
9
ADJUSTMENTS
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
9.6.2 SEAT MSG75 AIR SUSPENSION
WEIGHT ADJUSTMENT
The seat is adjusted for the driver’s weight by pulling
or pressing the lever for seat weight adjustment and
with the driver sitting on the seat.
The driver’s weight is adjusted correctly when the
arrow is in the middle clear area of the viewing
window.
Within this viewing area, the individual height can
be adjusted to a minimum spring movement.
When the minimum/maximum weight adjustment has
been reached, you can hear it reaching the upper
or lower end stop.
To prevent damage to the health and material, the
setting for the driver’s weight must be checked and
adjusted individually before the vehicle is driven.
In order to avoid compressor damage during weight
adjustment, the compressor must be operated no
longer than 1 minute.
FORE/AFT ADJUSTMENT
The fore/aft adjustment is released by lifting the
locking lever.
WARNING! Risk of accident!
Do not operate the locking lever while driving.
WARNING! Risk of crushing!
Only touch the lever at the indented grip, do not
reach back under the lever.
After the adjustment, the locking lever must latch into
the desired position with an audible click. It should
not be possible to move the driver’s seat into
another position when it is locked.
Do not lift the locking lever with your leg or calf.
en-47
9
ADJUSTMENTS
BACKREST EXTENSION
The backrest extension can be individually adjusted
by pulling it upwards or pushing it downwards over
the various locking increments up the end stop.
To remove the backrest extension, pull it upwards
over the end stop.
LUMBAR SUPPORT
The lumbar support increases both the seating
comfort and the performance of the driver.
By turning the adjustment knob upwards, the
curvature in the upper part of the backrest cushion
can be adjusted. By turning the knob downwards,
the curvature in the lower part of the backrest
cushion can be adjusted.
0 = No curvature
1 = Max. curvature at the top
2 = Max. curvature at the bottom
ARMRESTS
The armrests can be folded up if required and the
height individually adjusted.
To adjust the armrests for height, separate the
round cap (see arrow) from the cover, loosen the
hexagon nut (size 13 mm) behind it and adjust the
armrests to the desired position (5-steps) and
tighten the nut again.
Replace the cap onto the nut.
en-48
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
9
ADJUSTMENTS
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
ARMREST ADJUSTMENT
The inclination of the armrests can be modified by
turning the adjustment knob.
When turning the knob to the outside (+) the front
part of the armrest will be lifted, when turning the
knob to inside (-) it will be lowered.
BACKREST ADJUSTMENT
Moving the locking lever upwards loosens the
notching of the backrest adjustment.
After the adjustment, the locking lever must latch into
the desired position. It should not be possible to
move the backrest into another position when it is
locked.
For an ergonomic use the backrest can be adjusted
in a range of –5 to +30 degrees (15 steps of 2.5
degrees each).
MAINTENANCE
Dirt can impair the function of the seat,
so make sure you keep your seat clean!
Upholstery does not need to be removed from
the seat frame for cleaning.
Caution: Take care with the backrest - it may
jerk forward and cause injury!
When cleaning the backrest cushion the
backrest must be held in place when operating
the backrest lever.
Attention: Do not clean the seat with a
pressure washer!
During cleaning the upholstery should not be
soaked through.
Use a standard commercially available
upholstery or plastic cleaning agent. Test first
for compatibility on a small, concealed
area.
en-49
9
ADJUSTMENTS
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
9.6.3 SEAT MSG85 MECHANICAL SUSPENSION
The seat can be adjusted for operator's weight and
leg reach to provide a comfortable position for
operating the machine.
A. ADJUSTMENT FOR OPERATOR WEIGHT
To Adjust:
The position of the adjusting knob (A) is on the front
of the seat, in the centre below the seat cushion. By
rotating the knob clockwise the weight capacity is
increased and by rotating the knob anticlockwise
the weight capacity is decreased.
A
B. FORE AND AFT ADJUSTMENT
To Adjust:
The position of the adjusting lever is on the right
hand side of the seat below the seat cushion (B). By
moving the lever towards the seat, the seat can be
slid backwards and forwards. When in the desired
position release the lever to locate in one of the pre
set positions.
C. BACK REST ADJUSTMENT
The back rest has three preset positions
To Adjust:
The position of the release lever is on the left hand
side of the seat back rest (C). Move the lever
upwards to move the upper part of the back rest
forward. Move the lever downwards to move the
upper part of the back rest rearwards.
NOTE:The seat is fitted with a microswitch to sense
operator presence. When the machine is fitted with a
ROPS frame or cab a lap belt is fitted and should be
worn at all times
en-50
B
C
9
ADJUSTMENTS
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
en-51
10
TROUBLESHOOTING
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
10.1 GENERAL
The trouble shooting chart below lists basic problems that may occur during start-up and operation. For more
detailed information regarding the hydraulic and electrical systems contact your area Ransomes Distributor.
Symptoms
Possible Causes
Action
Section
1. Glow Plug has not timed out.
1. Reset ignition switch and allow glow plug to
time out before cranking engine.
2. Battery low on charge or
defective.
2. Inspect condition of battery and battery
connections.
3. Fuel tank empty or fuel
contaminated.
3. Fill tank with fresh fuel. Change filter, Bleed air
from lines.
4. Blown Fuse.
4. Replace Fuse.
5. Defective Starter Relay.
5. Test and replace relay if neccesary.
6. Parking brake not applied
6. Apply parking brake
7. Mow engage lever set to cut.
7. Put hydraulic drive lever into neutral.
1. Fuel tank empty or fuel
contaminated.
1. Fill tank with fresh fuel. Change filter, Bleed air
from lines.
2. Air Cleaner blocked or dirty.
2. Check air cleaner, replace as neccesary.
3. Injectors, fuel pump.
3. Consult engine manual.
4. Other Engine Problem
4. Consult engine trouble shooting guide.
1. Fuel tank empty
1. Fill with fresh fuel and bleed lines
2. Interlocks not set before
leaving operators seat
2. Apply parking brake and put hydraulic drive
lever into neutral.
1. Coolant level low
1. Inspect and add 50/50antifreeze solution if
required.
2. Radiator air intake restricted
2. Clean wire mesh guard at radiator.
3. Waterpump/alternator belt or
fan belt loose or broken.
3. Inspect waterpump/alternator belt and fan belt.
Tighten if neccesary.
1. Loose or corroded battery
terminals.
1. Inspect terminals, clean and tighten as
required.
2. Low electrolyte level in
battery.
2. Refill battery with distelled water
5.7
3. Alternator belt loose or
broken.
3. Inspectwaterpump/alternator bel. Tighten if
neccesary.
6.1
4. Alternator defective.
4. See engine manual.
1. Cylinder to bottom blade not
adjusted properly.
1. Inspect cylinder to bottom blade adjustment.
2. Engine speed too low.
2. Check engine speed, run engine at full throttle.
3. Cylinder speed not adjusted
for turf conditions.
3. Adjust cylinder speed for best cut.
4. Cylinder direction lever set
in reverse.
4. Set cylinder direction lever to forward rotation.
5. Ground weight incorrectly
adjusted
5. Adjust ground weight control valve till correct
ground weight is achieved.
5.6
Engine will not start.
Engine hard to start
or runs poorly.
Engine Stops.
Engine Overheating.
Battery not holding
charge. Battery light
on.
Cylinders cut
unevenly.
en-52
5.6
6.1
10
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
TROUBLESHOOTING
10.2 Quality of Cut Troubleshooting
It is recommended that a “test cut” be performed to evaluate the mower’s performance before beginning
repairs.
An area should be available where “test cuts” can be made. This area should provide known and consistent turf
conditions to allow accurate evaluation of the mower’s performance.
Another “test cut” should be performed after the completion of the repairs and/or adjustments to verify the
mower’s performance.
Before performing a “test cut” to diagnose cut appearance and mower performance, the following items should
be verified to ensure an accurate “test cut.”
1.
2.
3.
4.
5.
6.
7.
Mowing (Ground) Speed.
Reel Bearing Condition and Pre-Load (End Play) Adjustment.
Reel and Bedknife Sharpness.
Bedknife Alignment to Reel.
Reel-to-Bedknife Contact.
Height-of-Cut (HOC).
Roller and Roller Bearing Condition.
10.2.1
Washboarding
Washboarding is a cyclical pattern of varying cutting
heights, resulting in a wave-like cut appearance. In
most cases, the wave tip-to-tip distance is
approximately 6—8 in. (15—20 cm). Colour variation
(light-to-dark) may also be noticed.This condition is
usually caused by a rocking motion in the cutting
unit(s). This condition is found mostly on mowers with
multiple (suspended) cutting units, but other causes
can produce the same result.Washboarding may also
be caused by variations in the turf.
NOTE: Arrow indicates direction of travel.
Probable Cause
Remedy
Mowing (ground) speed is too fast.
Reduce mowing (ground) speed.
Grass build-up on roller.
Clean the roller and use scrapers or brushes.
Roller is out of round.
Replace roller.
Mowing in the same direction.
Change mowing direction regularly.
Use of a groomer on cleanup pass.
Groomers should be used only in a straight line.
en-53
10
TROUBLESHOOTING
10.2.3
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
Marcelling
Marcelling, like washboarding, is a cyclical pattern
of varying cutting heights, resulting in a wave-like
cut appearance. In most cases, the wave tip-to-tip
distance is 2 in. (5 cm) or less.
NOTE: Arrow indicates direction of travel.
Probable Cause
Mowing (ground) speed is too fast.
HOC (height-of-cut) setting is too low
for turf conditions.
Cutting reel diameter is worn.
en-54
Remedy
Reduce mowing (ground) speed.
Check/adjust HOC to turf conditions.
Check cutting reel diameter and replace if worn.
10
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
TROUBLESHOOTING
10.2.4
Step Cutting
Step cutting occurs when grass is cut taller on
one side of a reel than the other or one cutting
unit to another. This is usually caused by
mechanical wear or an incorrect roller or HOC
(height-of-cut) adjustment.
NOTE: Arrow indicates direction of travel.
Probable Cause
Remedy
HOC (height-of-cut) settings are
different from one side of a reel to the
other or from one cutting unit to
another.
Check HOC adjustment of cutting units.
Worn front roller bearings.
Check/replace front roller bearings.
Reel-to-bedknife contact is different
from one side of the cutting unit to the
other or from one cutting unit to
another.
Check reel-to-bedknife contact.
Cutting reel movement is restricted.
Check/remove cutting reel movement obstruction.
Variations in turf density.
Change mowing direction.
Machine weight distribution is uneven.
Check/adjust tire inflation pressure.
en-55
10
TROUBLESHOOTING
10.2.5
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
Scalping
Scalping is a condition in which areas of grass
are cut noticeably shorter than the surrounding
areas, resulting in a light green or even brown
patch. This is usually caused by an excessively
low height-of-cut (HOC) setting and/or uneven
turf.
NOTE: Arrow indicates direction of travel.
Probable Cause
Remedy
HOC (height-of-cut) settings are lower
than normal.
Check/adjust the HOC settings.
Improper reel-to-bedknife adjustment.
Adjust reel-to-bedknife setting for desired HOC.
Turf too uneven for the mower to
follow.
Change mowing direction.
Cutting too much grass at one time.
Mow more often.
Mowing (ground) speed is too fast.
Reduce mowing (ground) speed.
en-56
10
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
TROUBLESHOOTING
10.2.6
Stragglers
Stragglers are scattered blades of uncut or
poorly cut grass.
NOTE: Arrow indicates direction of travel.
Probable Cause
Remedy
Bedknife improperly adjusted.
Adjust reel-to-bedknife setting.
Dull reel or bedknife cutting edges.
Sharpen or replace reel blade and bedknife as
necessary.
Mowing (ground) speed is too fast.
Reduce mowing (ground) speed.
Grass is too tall.
Mow more often.
Mowing in the same direction.
Change mowing direction regularly.
Nicks in reel or bedknife.
Grind, sharpen or replace reel blades and bedknife
as necessary.
en-57
10
TROUBLESHOOTING
10.2.7
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
Streaks
A streak is a line of uncut grass. This is usually
caused by a nicked or bent bedknife.
NOTE: Arrow indicates direction of travel.
Probable Cause
Remedy
Damaged bedknife.
Replace bedknife.
Damaged or unevenly w orn reel.
Inspect reel. Replace as needed.
Loose or missing bedknife fasteners.
Check bedknife screw s. Tighten loose screw s;
replace missing screw s.
Turning too aggressively. Cutting units
don’t overlap around turns or on side
hills.
Turn less aggressively to allow cutting units to
overlap. Change mow ing direction or pattern on side
hills.
Tire mats dow n grass before it is cut.
Check/adjust tire inflation pressure.
Wet grass is matted dow n before it is
cut.
Mow w hen grass is dry.
en-58
10
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
TROUBLESHOOTING
10.2.8
Windrowing
Windrowing is the deposit of clippings
concentrated at one end of cutting unit(s) or
between two cutting units, forming a line in the
direction of travel.
NOTE: Arrow indicates direction of travel.
Probable Cause
Remedy
Grass is too tall.
Mow more often.
Mowing while grass is wet.
Mow when grass is dry.
Grass built up on roller(s).
Clean roller(s) and scraper(s).
Grass collecting on bedknife.
Adjust reel-to-bedknife setting.
en-59
10
TROUBLESHOOTING
10.2.9
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
Rifling Or Tramlining
Rifling or tramlining is a pattern of varying
cutting heights, resulting in a wave-like cut
appearance, usually due to heavy contact points
across a reel and/or bedknife.
NOTE: Arrow indicates direction of travel.
Probable Cause
Remedy
Reel and/or bedknife unevenly worn.
Inspect bedknife and reel. Sharpen or replace reel
and bedknife as necessary.
Missing, loose, or over torqued
bedknife screws.
Install, replace or tighten bedknife screws to proper
torque setting.
Mowing (ground) speed is too fast.
Reduce mowing (ground) speed.
10.2.10
Mismatched Cutting Units
Mismatched cutting units is a pattern of varying
cutting heights, resulting in a stepped cut
appearance, usually due to mismatched HOC
(height-of-cut) adjustment from one cutting unit
to another.
NOTE: Arrow indicates direction of travel.
Probable Cause
Remedy
HOC inconsistent from one cutting unit
to another.
Check/adjust HOC on cutting units.
Difference in mower ride height side to
side.
Check/adjust tire inflation pressure.
en-60
11
FUSES AND RELAYS
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
10.1 FUSES AND RELAYS - DIESEL
Fuse A –
Fuse B –
Fuse C –
Fuse D –
Fuse E –
Fuse F –
Fuse G –
Fuse H –
Fuse I –
Fuse J –
Fuse K –
Fuse L –
20 Amp (Ignition) Wire colours Green
& White.
20 Amp (Starter Soleniod) Wire
colours White/Green & White/Orange
10 Amp (Cab Supply) Wire colours
White & White/Purple
10 Amp (LH Side rear lights) Wire
colours Red & Red/Black
10 Amp (RH Side rear lights) Wire
colours Red & Red/Orange
10 Amp (LH Headlamp) Wire colours
Blue/Pink & Blue
10 Amp (RH Headlamp) Wire colours
Blue/Red & Blue
10 Amp (Battery + to Hazards) Wire
colours Brown & White/Orange
10 Amp (Ignition for Hazards/
Indicators) Wire colours Grey/Red &
White.
10 Amp (Beacon) Wire colours Purple/
Brown & Brown
10 Amp (Safety Circuit) Wire colours
Green & White
10 Amp (Spare)
Component L
Diode Bridge (Main Harness)
Component L1
Diode Bridge (Binnacle
Harness)
Component M –
Relay 2 (Safety circuit: mow
switch/parking brake) Wire
colours to holder White/red,
Black, White/yellow &
Green/grey
Component N –
Relay 1 (Safety circuit: seat
switch) Wire colours to holder
White/ orange, White/red,
Green/ orange & Black
Component 0 –
Flasher Relay Wire colours to
holder Green/ Black, Black &
Grey/yellow
Component P –
Seat Switch Delay Wire colours
to holder Green & Green/Blue
Component R –
Lamp Timer
en-61
11
FUSES AND RELAYS
FUSE S(TOP) – Brown wire to here will have an ‘H’
identification tag, this is the circuit for the
Glow Plug Heaters (Pre’Heat)
FUSE T (MIDDLE) – Brown wire to here will have an
‘A’ identification tag, this is the circuit for
the Alternator.
FUSE U (BOTTOM) – Brown wire to here will have
an ‘S’ identification tag, this is the circuit
for the Safety system.
NOTE: ANY RED ‘LIVE’ WIRE FROM BATTERY
CAN LOCATE ON TO ANY FUSE.
Relay V – 70 Amp (Heater Relay).
en-62
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
12
GUARANTEE / SALES & SERVICE
RANSOMES PARKWAY 2250 PLUS
SAFETY AND OPERATORS MANUAL
GUARANTEE
We GUARANTEE that should any defect in workmanship or material occur in the
goods within TWO YEARS or two thousand hours (on models equipped with hour
meters), or whichever occurs first.
Exception to this warranty will be Aeration products, which are covered for a period
of TWO-YEARS or five hundred hours (on models equipped with hour meters) or
whichever occurs first.
We will repair, or at our option, replace the defective part without making any charge
for labour or for materials, provided that the claim under this guarantee is made
through an authorised dealer and that the defective part shall, if we so request, be
returned to us or to the dealer.
This guarantee is in addition to, and does not exclude, any condition or warranty
implied by law, except that we accept no liability in respect of used/second-hand
goods, or in respect of defects which in our opinion are in any way or to any extent
attributable to misuse, lack of reasonable care or ordinary wear and tear, or to the
fitting of spares, replacements, or extra components which are not supplied or
approved by us for the purpose. The use of non-recommended oil or lubricant
nullifies the guarantee.
Damage through transport or normal wear does not come under the guarantee.
The warranty is extended to the original purchaser only and is not transferable to
subsequent owners. The warranty period begins on the date the product is delivered
to the end user (customer), unless otherwise agreed with the manufacturer. At the
end of the first year the owner must have the product serviced by an authorised
dealer to be eligible for the second year of warranty coverage.
SALES & SERVICE
A network of authorised Sales and Service dealers has been established and these
details are available from your supplier.
When service attention, or spares, are required for the machine, within or after the
guarantee period your supplier or any authorised dealer should be contacted. Always
quote the registered number of the machine.
If any damage is apparent when delivery is made, report the details at once to the
supplier of the machine.
en-63
Ransomes Jacobsen Limited
West Road, Ransomes Europark, Ipswich, IP3 9TT
English Company Registration No. 1070731
www.ransomesjacobsen.com
Jacobsen, A Textron Company
11108 Quality Drive, Charlotte,
NC 28273, USA
www.Jacobsen.com
Download PDF