Vivotek SD83xxE/-M Installation guide

Vivotek SD83xxE/-M Installation guide

P/N:625019001G Rev.: 1.1

All specifications are subject to change without notice.

SD83xxE/-M

Quick Installation Guide

English

繁中 簡中 日本語

Français Español

Speed Dome

Network Camera

Deutsch Português Italiano Türkçe Polski

Русский Č esky Svenska

Nederlands

Indonesia

Dansk

NEMA 4x • IP66 • Extreme Weatherproof

VIVOTEK INC.

6F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C.

|

T

: +886-2-82455282

|

F

: +886-2-82455532

|

E

: [email protected]

VIVOTEK Netherlands B.V.

Busplein 36, 1315KV, Almere, The Netherlands

|

T

: +31 (0)36 5389 149

|

F

: +31 (0)36 5389 111

|

E

: [email protected]

VIVOTEK USA, INC.

2050 Ringwood Avenue, San Jose, CA 95131

|

T

: 408-773-8686

|

F

: 408-773-8298

|

E

: [email protected]

Warning Before Installation

Power off the Network Camera as soon as smoke or unusual odors are detected.

Do not disassemble the Network Camera.

Do not insert sharp or tiny objects into the

Network Camera.

Do not manually pan and tilt the Network

Camera when the power is on.

Refer to your user’s manual for the operating temperature.

Do not touch the Network Camera during a lightning storm.

Do not drop the Network Camera.

1

Package Contents

SD83xxE/-M (with extended cables) Wall Mount Bracket / Screws

Screws / Alignment Sticker / T25

Stardriver / Desiccant Bags (SD8363E)

Ground Wire

Quick Installation Guide PC/ABS / Smoked Dome Cover

Software CD

510000210G

EN-1

2

Physical Description

Outer View

This drawing shows a camera with its dome cover removed.

Reset Button

Network LED

Status LED

Lens

The SD card slot is accessed by removing the top section using the

T25 stardriver.

Inner View

Camera Body

Board-to-board

Connector

SD/SDHC/SDXC Card Slot

EN-2

3

Hardware Installation

IMPORTANT:

If your camera comes without the dehumidifier, you should examine whether the color of the silica gel inside the chassis has turned red. If so, you should replace the desiccant bag.

To replace the desiccant bags:

1. Remove the dome cover by loosening 4 T25 anti-tamper screws.

2. Replace the desiccant bags by attaching them firmly to the inside of the chassis.

3. Re-install the dome cover.

Also note the following:

1. Do not install the camera in a raining day.

2. It takes approximately 2 days to suppress the moisture level to 30% or lower, either using the desiccant bags or the dehumidifier.

3. Condensation may still be observed from on the dome cover within 30 minutes.

HD WDR Pro

EN-3

3-1. Install the Wall-mount Bracket

1. The camera weighs 3.66kg. Select a rigid mounting location to prevent vibration to the camera. Attach the alignment sticker to the wall.

2 . Drill 4 pilot holes (10mm in diameter and 4cm deep) into the wall, and then hammer in threaded anchors. Note that you should hammer the anchors with hex nuts on them so that the threaded poles will not be deformed! If preferred, drill another hole for routing cables.

3. Secure the wall mount bracket to wall using 4 sets of captive washers and nuts.

2 3

1

NOTE:

1. IO wires are user-supplied.

2. Avoid touching the circuit boards to prevent damage by electro static discharge.

3. Use CAT5e, CAT6 cables only.

EN-4

3-2. Cabling Connections & Attach the Top Section

1. Hold your top section with one hand and pass all cables through the wallmount bracket.

5

4

3

1

2

2. Secure the top section to the wall mount bracket.

Note that you should turn and orient the top section so that the C mark is facing a direction 15 degrees off the center line.

Remove seal from the breathe hole on the top section if your camera comes with the dehumidifier.

C Mark

15°

Center line

EN-5

3. Connect cables and use sealants and putties to make sure cable joints and the cabling hole are waterproof.

4. Secure the included ground wire to the dome cap, pass it through the mount brack et, and connect the other end to a grounded conduit later.

5. Use the included hex wrench to secure the top section.

3-3. Mounting the Camera

1. Align the camera body with the top section. Align the alignment mark on the camera with that on the interface section. Push the camera up to match the top section.

2. Rotate the camera clockwise until its alignment mark is aligned with the "C" mark.

3. Use the included T25 stardriver to tighten the 3 anti-tamper screws from the top.

Make sure all parts have been securely tightened.

4

1

Alignment Mark

HD WDR Pro

2

3

C Mark

HD WDR Pro

HD WDR Pro

EN-6

4

Network Deployment

General Connection

1. Connect the Network Camera's Ethernet cable (CAT5e, CAT6) to a PoE Plus switch. A

30W PoE output port alone can not drive the onboard heater, and hence if using the PoE switch alone, the application does not apply in low-temperature condition. The 30W PoE plus can only drive the camera when it is working at a temperature higher than -5ºC.

IEEE 802.3at PoE Switch (30W output) and / or

AC 24V 3.5A Adapter

(User-supplied)

HD WDR Pro

2. Connect the power wires to an AC 24V power adaptor (user-supplied). The AC 24V adapter can drive the camera and the onboard heater.

You can connect both power sources for redundancy in power supply.

Power over Ethernet (High Power PoE)

When using a non-PoE switch

Use a High Power PoE power injector (separately purchased) capable of 60W output to connect between the Network Camera and a non-PoE switch. Sufficient power is required for low temperature conditions when the onboard heater is activated.

HD WDR Pro

EN-7

High Power PoE Power

Injector

Non-PoE Switch

5

Assigning IP Address

1. Install "Installation Wizard 2" from the Software Utility directory on the software CD.

2. The program will conduct an analysis of your network environment. After your network is analyzed, please click on the "Next" button to continue the program.

3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network

Cameras on the same LAN.

4. After a brief search, the main installer window will pop up. Double-click on the MAC address that matches the one printed on the camera label or the S/N number on the package box label to open a browser management session with the Network Camera.

6

Ready to Use

1. A browser session with the Network Camera should prompt as shown below.

2. You should be able to see live video from your camera. You may also install the

32-channel recording software from the software CD in a deployment consisting of multiple cameras. For its installation details, please refer to its related documents.

28x

For further setup, please refer to the user's manual on the software CD.

EN-8

625023800G_QIG, IP83x5EH,V1.0_20140105.indd 80 2014/1/10 下午 02:01:40

P/N:625019001G Rev.: 1.1

All specifications are subject to change without notice.

SD83xxE/-M

Quick Installation Guide

English

繁中 簡中 日本語

Français Español

Speed Dome

Network Camera

Deutsch Português Italiano Türkçe Polski

Русский Č esky Svenska

Nederlands

Indonesia

Dansk

NEMA 4x • IP66 • Extreme Weatherproof

VIVOTEK INC.

6F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C.

|

T

: +886-2-82455282

|

F

: +886-2-82455532

|

E

: [email protected]

VIVOTEK Netherlands B.V.

Busplein 36, 1315KV, Almere, The Netherlands

|

T

: +31 (0)36 5389 149

|

F

: +31 (0)36 5389 111

|

E

: [email protected]

VIVOTEK USA, INC.

2050 Ringwood Avenue, San Jose, CA 95131

|

T

: 408-773-8686

|

F

: 408-773-8298

|

E

: [email protected]

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement