ELPS Light-Pak™ Emergency Lighting System

ELPS Light-Pak™
Emergency Lighting
System
Cl.l, Div. 1 & 2; Groups C,D
Cl. I, Div. 1 & 2, Groups B.C.D
(With suffix GB)
Cl. II, Div.1; Groups E.F.G
Cl. Ill
Simultaneous Presence
Wet Locations
NEMA3,3R,12
9L-3
Application:
ELPS series emergency lighting systems are
used:
• to provide safe, reliable illumination indoors
or outdoors to designated areas during
failure or interruption of power to the normal
lighting system
• in areas made hazardous by the presence
of flammable gases and vapors, combustible
dusts or easily ignitible fibers and flyings
• in areas where corrosion, vibration,
moisture, dirt and rough usage may be
encountered
• where required by the National Electrical
Code®, the Life Safety Code or other codes
• in refineries, chemical and petrochemical
facilities, grain processing, handling or
storage facilities, manufacturing plants, waste
water treatment facilities and other areas
where safe, reliable, hazardous area
emergency lighting is needed
Features:
• Compact factory sealed fixture assemblies
are each furnished with a 14 watt tungstenhalogen lamp and inner reflector for
appropriate photometries in hazardous
areas.
• Fixture assemblies are fully adjustable and
lockable on two axes to provide flexible and
consistent light aiming capabilities.
• Fixture lens ring is threaded for easy
relamping and locks in place with hex head
set screw; will not loosen due to vibration.
• Ground joint cover with external flange
design permits large opening and easy
access to internal components. Stud bolts in
diagonally opposite corners of body ease
cover removal and installation.
• Neoprene cover gasket seals out moisture
for superior protection of internal
components against wetness and corrosion.
• Light weight, compact size, and mounting
feet ease installation and allow placement in
confined areas.
• Two 1" NPT drilled and tapped conduit
openings, with plugs, are standard, for
choice of top or bottom feed.
• Factory-installed PUSH-TO-TEST
pushbutton enables easy testing of system.
• MAIN POWER ON pilot light indicates AC
power is being supplied to the battery
charger; pilot light jewel is threaded for easy
lamp replacement.
• Stainless steel drain minimizes moisture
collection. Stainless steel breather with
aluminum cap provides ventilation, minimizes
moisture collection.
• CID101 corrosion inhibitor device is
provided with each ELPS system to help
protect electrical components and
connections.
• Rugged, long-life, maintenance-free, nickel
cadmium battery provides 30 watts of power
for the required 1!/2 hours.
• Solid state battery charger for long life and
reliable service prevents deep discharge by
automatically disconnecting fixtures from
battery.
• Terminal block facilitates field wiring
connections.
• Instruction sheet and maintenance record
card provided with unit in a protective plastic
envelope.
• A time delay is standard; time delay is
preset at factory for 5 minute delay but can
be field set for 5 seconds or 15 minutes, thus
allowing HID type lamps time to restrike and
reach desired illumination levels.
• Solid state battery charger will accept 120,
220/240 or 277 VAC, 50/60 Hz.
Electrical Ratings:
• Power supply:
Input: 120, 220/240, 277 VAC, 50 or
60 hertz
0.5 Amps Maximum
Output: 12 VDC
UL listed for 30 watts for 11/2 hours
at 40°C
• Lighting fixtures:
Voltage: 12 VDC
Lamp Type: #789, miniature
tungsten halogen, G4, 2-pin, 14 watt.
Certifications and
Compliances:
• NEC: Class I, Groups B
(with GB suffix), C,D
Class II, Groups E, F, G
Class III
Simultaneous Presence
• UL Standard:
844 - Electric Lighting Fixture Hazardous Locations
924 - Emergency Lighting and Power
Equipment
1203 - Explosionproof and DustIgnition-Proof Electrical
Equipment
• Life Safety Code:
Section 5-9 (Emergency Lighting)
• Suitable for Wet Locations
• NEMA3, 3R, 12
0
Copyright 2000 Cooper Industries, Inc.
Standard Materials:
• Power supply enclosure and fixture
assembly - copper-free aluminum (less than
0.4 of 1% copper)
Standard Finishes:
• Aluminum - gray powder epoxy finish
Ordering Information:
Description
Cat. #
Power supply with two lighting fixture
assemblies
ELPS502
Lighting fixture assembly only
EVLA12
Power supply only
ELPS50
Power Supply with 1-EVLA12 and Single
Face Exit Sign with Red Letters. Exit
Sign operates in emergency mode only.
ELPS502-EXS
Power Supply with 1-EVLA12 and Double
Face Exit Sign with Red Letters. Exit
Sign operates in emergency mode only.
ELPS502-EXD
Options:
Suffix to be
Added to
Description
Cat. No.
ELPS502 - suitable for Group B
GB
ELPS50 - suitable for Group B
GB
EVLA12 - suitable for Group B
GB
Integral Battery Disconnect Switch disconnects lighting fixtures from
battery for added safety during
maintenance
S794
Exit Sign with green letters
GN
ELPS502 with Exit Sign EXS or EXD that
operates in both normal & emergency mode.
consult Grouse Hinds