Advantech MIO-5250 N2600, D2550 Compact SBC User Manual
Below you will find brief information for Compact SBC MIO-5250 N2600, Compact SBC MIO-5250 D2550. MIO-5250 is a MI/O-Compact SBC with Intel® Atom™ Cedar Trail ultra low power solution supporting up to 4GB 800/1066MHz DDR3, 6 USB2.0, SATAII (300 MBs), 4 COM and 2 GbE (up to 1000 Mbps). The boards support dual displays including VGA+LVDS, VGA+HDMI, and HDMI+LVDS. With flexible storage options including mSATA and CFast. MIO-5250 supports DisPlayPort, PCIe x1, USB2.0, LPC, SMBus, HD audio line out and Power from MIOe. Users can choose from a standard module or design their own modules to secure domain knowledge and expedite their design schedule.
advertisement
User Manual
MIO-5250
Intel® Atom™ N2600/ D2550,
3.5" MI/O-Compact SBC, DDR3,
HDMI, LVDS, VGA, 2 GbE, CFast, iManager, MIOe
Copyright
The documentation and the software included with this product are copyrighted 2013 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co.,
Ltd. Information provided in this manual is intended to be accurate and reliable. However, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringements of the rights of third parties, which may result from its use.
Acknowledgements
Intel® is a trademark of Intel® Corporation.
IBM, PC/AT, PS/2 and VGA are trademarks of International Business Machines Corporation.
Microsoft Windows is a registered trademark of Microsoft Corp.
CHRONTEL is a trademark of Chrontel Inc.
All other product names or trademarks are properties of their respective owners.
MIO-5250 User Manual
Part No. 2006M52512
Printed in China ii
Edition 3
March 2013
Product Warranty (2 years)
Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for two years from the date of purchase.
This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech, or which have been subject to misuse, abuse, accident or improper installation. Advantech assumes no liability under the terms of this warranty as a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous testing, most of our customers never need to use our repair service. If an Advantech product is defective, it will be repaired or replaced at no charge during the warranty period. For outof-warranty repairs, you will be billed according to the cost of replacement materials, service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1.
Collect all the information about the problem encountered. (For example, CPU speed, Advantech products used, other hardware and software used, etc.) Note anything abnormal and list any onscreen messages you get when the problem occurs.
2.
Call your dealer and describe the problem. Please have your manual, product, and any helpful information readily available.
3.
If your product is diagnosed as defective, obtain an RMA (return merchandise authorization) number from your dealer. This allows us to process your return more quickly.
4.
Carefully pack the defective product, a fully-completed Repair and Replacement
Order Card and a photocopy proof of purchase date (such as your sales receipt) in a shippable container. A product returned without proof of the purchase date is not eligible for warranty service.
5.
Write the RMA number visibly on the outside of the package and ship it prepaid to your dealer.
Declaration of Conformity
CE
This product has passed the CE test for environmental specifications. Test conditions for passing included the equipment being operated within an industrial enclosure. In order to protect the product from being damaged by ESD (Electrostatic Discharge) and EMI leakage, we strongly recommend the use of CE-compliant industrial enclosure products.
FCC Class A
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
iii MIO-5250 User Manual
Technical Support and Assistance
1.
Visit the Advantech web site at www.advantech.com where you can find the latest information about the product.
2.
Contact your distributor, sales representative, or Advantech's customer service center for technical support if you need additional assistance. Please have the following information ready before you call:
– Product name and serial number
– Description of your peripheral attachments
– Description of your software (operating system, version, application software, etc.)
– A complete description of the problem
– The exact wording of any error messages
Warnings, Cautions and Notes
Warning! Warnings indicate conditions, which if not observed, can cause personal injury!
Caution! Cautions are included to help you avoid damaging hardware or losing data. e.g.
There is a danger of a new battery exploding if it is incorrectly installed.
Do not attempt to recharge, force open, or heat the battery. Replace the battery only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer's instructions.
Note!
Notes provide optional additional information.
Document Feedback
To assist us in making improvements to this manual, we would welcome comments and constructive criticism. Please send all such - in writing to: [email protected]
MIO-5250 User Manual iv
Packing List
Before setting up the system, check that the items listed below are included and in good condition. If any item does not accord with the table, please contact your dealer immediately.
1 x MIO-5250 SBC
1 x SATA Cable 32cm
1 x SATA Power Cable 35cm
1 x Audio Cable 20cm
2 x COM RS-232 Cable 22cm
2 x COM RS-422/485 Cable 25cm
1 x Heatsink (20mm)
Startup Manual
CD-ROM (User manual and drivers)
1 x Mini Jumper(10pcs package)
(P/N 1700008941)
(P/N 1700018785)
(P/N 1700019584)
(P/N 1701200220)
(P/N 1700019435)
(P/N 1960054272T001)
(P/N 9689000002)
Ordering Information
MIO-5250N-S6A1E Intel® Atom™ N2600 Dual Core + NM10
MIO-5250D-S8A1E Intel® Atom™ D2550 Dual Core + NM10
CPU
L2 Cache
MIO-5250N-S6A1E
Intel® Atom™ N2600 1.6G Dual
Core
1 MB L2
LVDS 24 bit LVDS1
VGA
HDMI
GbE
Audio
RS-232/422/485
RS-232
USB 2.0
Yes
Yes
2
2
6
Yes
2
GPIO
SATAII
CFast 1
Full-size Mini PCIe 1
8-bit
1
MIOe
Thermal Solution
Yes
Fanless
Operational Temp.
0 ~ 60° C
MIO-5250D-S8A1E
Yes
2
Yes
2
2
6
8-bit
1
Intel® Atom™ D2550 1.86G Dual
Core
1 MB L2
24 bit LVDS1
48 bit LVDS2
Yes
1
1
Yes
Fanless
0 ~ 60° C v MIO-5250 User Manual
Optional MIOe Module
Part Number Description
MIOe-210-D6A1E
4x RS232/422/485 2x RS422/485 with DSUB connector, 8-bit
GPIO
MIOe-220-B3A1E
MIOe-230-L0A1E*
3 x GbE with RJ45 connector through PCIe switch
Displayport to 48-bit LVDS
MIOe-DB5000-01A1E* MI/O extension evaluation board w/ PCIe switch
*MIOe-230 compatibility is optional by request (need BOM update).
Optional Accessories
Part number
1960054269T001
1703100260
1935032000
1930000058
1757003934
Description
Heat spreader 137x84.2x16.7-mm MIO-5250
Internal USB 5/6 cable
Screw of Heatsink / Cooler R/S 5.5 2.0 +M M3*20L ST Ni
The POST Stand off, F=M3*8L M=M3*4L D=5 H=19L Cu
ADAPTER 100-240V 60W 12V 5A W/O PFC
Safety Instructions
1.
Read these safety instructions carefully.
2.
Keep this User Manual for later reference.
3.
Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning.
4.
For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible.
5.
Keep this equipment away from humidity.
6.
Put this equipment on a reliable surface during installation. Dropping it or letting it fall may cause damage.
7.
The openings on the enclosure are for air convection. Protect the equipment from overheating. DO NOT COVER THE OPENINGS.
8.
Make sure the voltage of the power source is correct before connecting the equipment to the power outlet.
9.
Position the power cord so that people cannot step on it. Do not place anything over the power cord.
10.
All cautions and warnings on the equipment should be noted.
11.
If the equipment is not used for a long time, disconnect it from the power source to avoid damage by transient overvoltage.
12.
Never pour any liquid into an opening. This may cause fire or electrical shock.
13.
Never open the equipment. For safety reasons, the equipment should be opened only by qualified service personnel.
MIO-5250 User Manual vi
14.
If one of the following situations arises, get the equipment checked by service personnel:
The power cord or plug is damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
The equipment does not work well, or you cannot get it to work according to the user's manual.
The equipment has been dropped and damaged.
The equipment has obvious signs of breakage.
15.
DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE
STORAGE TEMPERATURE MAY GO BELOW -20° C (-4° F) OR ABOVE 60° C
(140° F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT
SHOULD BE IN A CONTROLLED ENVIRONMENT.
16.
CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY
REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE
RECOMMENDED BY THE MANUFACTURER, DISCARD USED BATTERIES
ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS.
The sound pressure level at the operator's position according to IEC 704-1:1982 is no more than 70 dB (A).
DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech disclaims all responsibility for the accuracy of any statements contained herein.
Safety Precaution - Static Electricity
Follow these simple precautions to protect yourself from harm and the products from damage.
To avoid electrical shock, always disconnect the power from your PC chassis before you work on it. Don't touch any components on the CPU card or other cards while the PC is on.
Disconnect power before making any configuration changes. The sudden rush of power as you connect a jumper or install a card may damage sensitive electronic components.
vii MIO-5250 User Manual
MIO-5250 User Manual viii
Contents
Chapter 1
General Information
............................1
General Specification.................................................................... 2
Functional Specifications .............................................................. 3
Mechanical Specifications............................................................. 4
Electrical Specifications ................................................................ 5
Environmental Specifications........................................................ 5
Figure 1.1 Block Diagram ............................................................ 6
Chapter 2
Hardware Installation
..........................7
Jumper List ................................................................................... 8
Table 2.1: Jumpers...................................................................... 8
Jumper Settings ............................................................................ 8
Jumper Description ..................................................................... 10
Connector List............................................................................. 11
Table 2.2: Connectors ............................................................... 11
Jumper and Connector Location................................................. 12
Figure 2.1 Jumper and Connector Layout (Top Side) ............... 12
Figure 2.2 Jumper and Connector Layout (Bottom Side) .......... 12
Board Dimensions....................................................................... 13
Figure 2.3 Board Dimensions (Component Side) ...................... 13
Figure 2.4 Board Dimensions (Solder Side) .............................. 13
Figure 2.5 I/O Connectors Mechanical Drawing ........................ 14
Chapter 3
BIOS Settings
.....................................15
Figure 3.1 Setup program initial screen..................................... 16
Figure 3.2 Main setup screen .................................................... 17
System date / System time ......................................................... 17
Advanced BIOS Features Setup ............................................................. 18
Figure 3.3 Advanced BIOS features setup screen .................... 18
Advantech BIOS Update V1.3 .................................................... 18
ACPI Settings.............................................................................. 19
Figure 3.4 ACPI Setting ............................................................. 19
TPM Configuration ...................................................................... 20
Figure 3.5 TPM Configuration.................................................... 20
CPU Configuration ...................................................................... 20
Figure 3.6 CPU Configuration.................................................... 20
SATA Configuration .................................................................... 21
Figure 3.7 SATA Configuration.................................................. 21
Intel Fast Flash Standby ............................................................. 22
Figure 3.8 Intel Fast Flash Standby........................................... 22
USB Configuration ...................................................................... 22
Figure 3.9 USB Configuration.................................................... 22
ix MIO-5250 User Manual
Embedded Controller Configuration ........................................... 23
Figure 3.10Embedded Controller Configuration ......................... 23
Super I/O Configuration .............................................................. 24
Figure 3.11Super IO Configuration............................................. 24
3.4.10 AOAC Configuration ................................................................... 25
Figure 3.12AOAC Configuration................................................. 25
3.4.11 PPM Configuration...................................................................... 25
Figure 3.13PPM Configuration ................................................... 25
Figure 3.14Chipset Setup........................................................... 26
Host Bridge/Intel IGD Configuration ........................................... 27
Figure 3.15Intel IGD Configuration............................................. 27
South Bridge ............................................................................... 28
Figure 3.16South Bridge............................................................. 28
Figure 3.17TPT Device............................................................... 29
Figure 3.18Boot Setup Utility...................................................... 30
Figure 3.19Password Configuration ........................................... 31
Figure 3.20Save & Exit............................................................... 32
Save Changes and Exit .............................................................. 32
Discard Changes and Exit .......................................................... 32
Save Changes and Reset........................................................... 32
Discard Changes and Reset....................................................... 32
Save Changes ............................................................................ 32
Discard Changes ........................................................................ 33
Restore Defaults ......................................................................... 33
Save User Defaults..................................................................... 33
Restore User Defaults ................................................................ 33
Chapter 4 MIOe Installation
............................... 35
Appendix A Pin Assignments
............................... 37
Appendix B System Assignments
........................ 59
Table B.1: System I/O Ports ...................................................... 60
DMA Channel assignments .................................................................... 60
Table B.2: DMA Channel assignments...................................... 60
1st MB memory map............................................................................... 61
Table B.3: 1st MB memory map ................................................ 61
Table B.4: Interrupt assignments............................................... 61
Appendix C Watchdog Timer Sample Code
........ 63
EC Watchdog Timer sample code .......................................................... 64
MIO-5250 User Manual x
Chapter
1
General Information
1
1.1
Introduction
Advantech created the stackable architecture MI/O Extension Single Board Computer as a SBC design with flexible and multiple I/O support (hence the name MI/O) and united extended interface connector. MIO-5250 is a MI/O-Compact SBC (Single
Board Computer) with Intel
®
Atom™ Cedar Trail ultra low power solution supporting up to 4GB 800/1066MHz DDR3, 6 USB2.0, SATAII (300 MBs), 4 COM and 2 GbE (up to 1000 Mbps). MIO-5250 supports dual displays, including VGA+LVDS, VGA+HDMI, and HDMI+LVDS. Also have flexible storage option, including mSATA and CFast. In addition, MIO-5250 supports DisPlayPort, PCIe x1, USB2.0, LPC, SMBus, HD audio line out and Power from MIOe. Users can choose from a standard module or design their own modules to secure domain knowledge and expedite their design schedule.
1.2
Specifications
1.2.1
General Specification
CPU
L2 Cache
Watchdog Timer
Expansion Interface
Battery
CPU: Intel ® Atom
- N2600 (Dual Core 1.6GHz) on MIO-5250N-S6A1E
- D2550 (Dual Core 1.86GHz) on MIO-5250D-S8A1E
N2600: 1MB
D2550: 1MB
System Chipset
BIOS
Intel ® Atom N2600 / D2550 + NM10
AMI EFI 16-Mbit
System Memory
1 x 204-pin SODIMM socket DDR3 up to 4GB:
N2600: up to DDR3 800 MHz
D2550: up to DDR3 1066 MHz
Power Management APM1.2, ACPI support
255 levels timer interval, programmable by software. Multi level WDT
(set by iManager)
Full-size Mini PCIe with SIM Holder (supports mSATA via BIOS select), CFast, MIOe
Lithium 3 V / 210 mAH
I/O
Internal I/O Interface
Rear I/O
Power Connector
Type
1 x SATAII, 2 x RS-232, 2 x RS232/422/485, 2 x USB 2.0, GPIO,
SMBus, HD Audio
4 x USB 2.0, HDMI, VGA, 2 x RJ45 Ethernet, Power connector
MIO-5250N-S6A1E: DC Jack
MIO-5250D-S8A1E: 2 x 2 pin Power connector
SMBus Supported
I 2 C
GPIO
Supported (Shares with SMBus pin)
8-bit general purpose input/output
Ethernet
Speed
Chipset
Ethernet Interface
GbE 10/100/1000 Mbps
Intel ® 82583V (GbE1, GbE2)
Fully compliant with IEEE 802.3, IEEE 802.3u, IEEE 802.3ab
MIO-5250 User Manual 2
Connector
Wake On Function
Display
RJ45 x2
Wake-on-LAN
Controller
Resolution
Intel ® Atom N2600 / D2550
VGA: N2600 / D2550: 1920 x 1200
LVDS:
N2600: 24-bit LVDS1, resolution up to1366 x 768
D2550: 24-bit LVDS1, resolution up to 1440 x 900,
48-bit LVDS2 (JEIDA support), resolution up to 2560 x
1600
(LVDS1 or LVDS2 both need select “Built-in Display” in OS)
HDMI:
Supports 1920 x 1200p @60Hz, 36bpp
Supports HDMI 1.3, Max data rate up to 1.65Gb/s
Dual Independent Display VGA+LVDS, VGA+HDMI, HDMI+LVDS
1.2.2
Functional Specifications
Processor: Intel
®
Atom N2600/D2550
CPU Process
Frequency
VGA Memory
Internal Graphics Features
Video Accelerator
32nm
- N2600: 1.6GHz
- D2550: 1.86GHz
Up to 512MB of dynamic video memory allocation
DirectX® 9 and OpenGL 3.0
Display Port 1.1, HDMI 1.3a
Supports HDCP 1.3
Intel
®
Display Power saving technology 6.0
SGXS45 Power VR Core 400/640 MHz
H/W accelerated video decode
Video decoder: Support MPEG4, VC1, WMV9, H.264
Supports DVD, Blu-ray, and HD video
1.2.2.1
Chipset (NM10)
South Bridge
Control Hub
RS-232
RS-232/422/485
K/B
Mouse
USB
Audio
Other Features
BIOS
1
1
NM10
2
2
6 x USB 2.0
HD Audio, ALC892 Codec, Line-in, Line-out, Mic-in, speaker out (R/L)
(Supports 8 Ω 1W or 4 Ω 2 W Speaker for Speaker-out)
* 6 x USB 2.0 ports, 480MB/s (all internal connectors)
Default: 500mA @ one port (Up to 1A @ 2 ports)
* 1 x SATAII (Max. Data transfer Rate 300MB/s)
* HD Audio CODEC (ALC892)
* Power Management (S0, S3,S4, S5)
16-Mbit Flash BIOS via SPI
3 MIO-5250 User Manual
1.2.2.2
iManager iManager
Sequence control Supported
SMBus Supported
GPIO 8-bit GPIO
Watchdog timer
Multi Level WDT (set by Advantech iManager)
Programmable 1-255 sec / min
Hardware monitor
Power saving
Board information
Input Voltage
Deep sleep S5 mode/Back light control
Running HR / Boot record
Storage Read / Write data protection
VGA Low Level Backlight / Brightness control
1.2.2.3
Others
Gigabit Ethernet
Chipset
IEEE Compliant
Disable LAN through
BIOS
Driver Support
High Definition
Audio
Codec
Connector
Voltage
Intel ® 82583V (GbE1, GbE2)
Fully compliant with IEEE 802.3, IEEE 802.3u, IEEE 802.3ab
Yes
WES7
Realtek ALC892
Line in, Line out, Mic in
+3.3V, +5V, +12V, Vcore
1.2.3
Mechanical Specifications
1.2.3.1
Dimensions (mm)
146 x 102 mm (5.7 x 4 inches)
1.2.3.2
Board height on Top side (mm)
16.4mm (Rear I/O USB)
1.2.3.3
Board height on bottom side (mm)
9mm (Full-size Mini PCIe socket)
1.2.3.4
Heatsink/Cooler Dimensions (mm)
137mm (L) x 87.2mm (W) x 25mm (H)
1.2.3.5
Board net weight without heatsink (g)
140 g
MIO-5250 User Manual 4
1.2.4
Electrical Specifications
1.2.4.1
Power Supply Voltage
Power Type
Single 12V DC power in
Power Supply Voltage
Single 12V ± 10%
1.2.4.2
Power Consumption
Test Condition:
Add-in Card - None
Full-size Mini PCIe - None
Memory - DDR3 SODIMM 2GB
HDD - 3.5" WD 80GB SATA2 *1
KeyBoard/Mouse - USB
Display - VGA
Condition
MIO-5250N-S6A1E
MIO-5250D-S8A1E
Voltage/
Condition
+12V
+12V
Power Consumption (A)
DOS Idle Mode Win. Idle Mode
0.606
0.829
0.524
0.739
Win. HCT12
(10minutes)
0.729
1.029
1.2.4.3
RTC Battery
Typical Voltage: 3.0 V
Normal discharge capacity: 210 mAh
1.2.5
Environmental Specifications
1.2.5.1
Operating Temperature
Operating temperature: 0 ~ 60°C (32~140°F)
1.2.5.2
Operating Humidity
Operating Humidity: 0% ~ 90% Relative Humidity, non-condensing
1.2.5.3
Storage Temperature
Standard products (0~60°C)
Storage temperature: -40~85°C
1.2.5.4
Storage Relative Temperature
Standard products (0~60°C)
Relative humidity: 95% @ 60°C
Phoenix products (-20~80°C)
Relative humidity: 95% @ 60°C
Platinum Phoenix products (-40~85°C)
Relative humidity: 95% @ 60°C
5 MIO-5250 User Manual
1.3
Block Diagram
DDR3
SODIMM x 1
Intel Atom
N2600 / D2550
DisplayPort 1
VGA I/F
DisplayPort 0
Transmitter
18/24-bit LVDS1
VGA
HDMI
48-bit LVDS2
DMI
(note1)
Intel 82583V
Intel 82583V
COM1~COM4
(COM2/3: RS-232/422/485)
(COM1/4: RS-232)
Auto Flow Control
Full-size MiniPCIe w/ SIM Holder
16MBit
SPI BIOS
PCIe x 1
PCIe x 1
Super I/O LPC
Intel NM10
PCIe x 1
SPI
6 USB 2.0
HD audio line out
USB 2.0 x 1
SMBUS
LPC
1 PCIe x 1
MIOe
SATAII 1 x SATAII
Advantech iManager
HD
Realtek
ALC 892
CFast 8-bit GPIO SMBus/I 2 C
Figure 1.1 Block Diagram
Note1: Support by request
MIO-5250 User Manual 6
Chapter
2
Hardware Installation
2
This chapter explains the setup procedures of the MIO-5250 A1 hardware, including instructions on setting jumpers and connecting peripherals, switches, indicators and mechanical drawings. Be sure to read all safety precautions before you begin the installation procedure.
2.1
Jumpers
2.1.1
Jumper List
Table 2.1: Jumpers
Label Function
J3 Auto Power on setting
2.1.2
Jumper Settings
J1
Part Number
Footprint
Description
Setting
(1-3)*
(3-5)
(3-4)
24 bits LVDS1 Power
1653003260
HD_3x2P_79
PIN HEADER 3x2P 2.0mm 180D(M) SMD 21N22050
Function
+3.3V (default)
+5V
+12V
J2
Part Number
Footprint
Description
Setting
(1-3)*
(3-5)
(3-4)
MIO-5250 User Manual
48 bits LVDS2 Power
1653003260
HD_3x2P_79
PIN HEADER 3x2P 2.0mm 180D(M) SMD 21N22050
Function
+3.3V (default)
+5V
+12V
8
J3
Part Number
Footprint
Description
Setting
NC
(1-2)*
Auto Power On Setting
1653002101
HD_2x1P_79_D
PIN HEADER 2*1P 180D(M)SQUARE 2.0mm DIP W/O Pb
Function
Power Button for Power On
Auto Power On (default)
J4
Part Number
Footprint
Description
Setting
(1-2)*
(3-4)
(5-6)
COM2 Setting
1653003260
HD_3x2P_79
PIN HEADER 3x2P 2.0mm 180D(M) SMD 21N22050
Function
RS232 (default)
RS485
RS422
J5
Part Number
Footprint
Description
Setting
(1-2)*
(3-4)
COM3 Setting
1653003260
HD_3x2P_79
PIN HEADER 3x2P 2.0mm 180D(M) SMD 21N22050
Function
RS232 (default)
RS485
9 MIO-5250 User Manual
(5-6) RS422
J6
Part Number
Footprint
Description
Setting
(1-2)*
(2-3)
Clear CMOS
1653003101
HD_3x1P_79_D
PIN HEADER 3x1P 2.0mm 180D(M) DIP 2000-13 WS
Function
Normal (default)
Clear COMS
2.1.3
Jumper Description
Cards can be configured by setting jumpers. A jumper is a metal bridge used to close an electric circuit. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To close a jumper, you connect the pins with the clip. To open a jumper, you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3. In this case you would connect either pins 1 and 2, or 2 and 3.
The jumper settings are schematically depicted in this manual as follows.
MIO-5250 User Manual 10
A pair of needle-nose pliers may be helpful when working with jumpers. If you have any doubts about the best hardware configuration for your application, contact your local distributor or sales representative before you make any changes.
Warning! To avoid damaging the computer, always turn off the power supply before setting jumpers to clear CMOS. Before turning on the power supply, set the jumper back to 3.0 V Battery On.
2.2
Connectors
2.2.1
Connector List
Table 2.2: Connectors
Label Function
CN7 Reset
CN9 GPIO
CN10 VGA
CN11 CFast
CN14 SATA
CN25 SMBus
CN28 LAN
CN30 Audio
CN31 MIOe
CN33 24 bits LVDS1 Panel
CN34
CN35
48 bits LVDS2 Inverter Power
48 bits LVDS2 Panel
CN36 HDMI
CN38 LVDS1 Inverter Power
11 MIO-5250 User Manual
2.3
Mechanical
2.3.1
Jumper and Connector Location
y
CN22 CN20 CN14 p
J6 CN15 CN26
CN34
CN7
CN3
CN33
CN5
CN38
J3
CN17
J2
CN9
J1
CN35
CN18
CN25
CN16 CN36 CN10
CN28
CN2
HDD & PWR LED
Figure 2.1 Jumper and Connector Layout (Top Side)
CN12
MIO-5250 User Manual
CN19 CN24 J4 J5 CN13 CN30
Figure 2.2 Jumper and Connector Layout (Bottom Side)
12
CN11
CN31
2.3.2
Board Dimensions
Figure 2.3 Board Dimensions (Component Side)
Figure 2.4 Board Dimensions (Solder Side)
13 MIO-5250 User Manual
Figure 2.5 I/O Connectors Mechanical Drawing
MIO-5250 User Manual 14
Chapter
3
BIOS Settings
3
3.1
BIOS Setup
AMIBIOS has been integrated into many motherboards for over a decade. With the
AMIBIOS setup program, you can modify BIOS settings and control the various system features. This chapter describes the basic navigation of the MIO-5250 BIOS setup screens.
Figure 3.1 Setup program initial screen
AMI's BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This information is stored in flash ROM so it retains the Setup information when the power is turned off.
3.2
Entering Setup
Turn on the computer and then press <F2> or <DEL> to enter the Setup menu.
MIO-5250 User Manual 16
3.3
Main Setup
When users first enter the BIOS Setup Utility, users will enter the Main setup screen.
Users can always return to the Main setup screen by selecting the Main tab. There are two Main Setup options. They are described in this section. The Main BIOS
Setup screen is shown below.
Figure 3.2 Main setup screen
The Main BIOS setup screen has two main frames. The left frame displays all the options that can be configured. Grayed-out options cannot be configured; options in blue can. The right frame displays the key legend.
Above the key legend is an area reserved for a text message. When an option is selected in the left frame, it is highlighted in white. Often a text message will accompany it.
3.3.1
System date / System time
Use this option to change the system time and date. Highlight System Time or System Date using the <Arrow> keys. Enter new values through the keyboard. Press the
<Tab> key or the <Arrow> keys to move between fields. The date must be entered in
MM/DD/YY format. The time must be entered in HH:MM:SS format.
17 MIO-5250 User Manual
3.4
Advanced BIOS Features Setup
Select the Advanced tab from the MIO-5250 setup screen to enter the Advanced
BIOS Setup screen. You can select any of the items in the left frame of the screen, such as CPU Configuration, to go to the sub menu for that item. You can display an
Advanced BIOS Setup option by highlighting it using the <Arrow> keys. All Advanced
BIOS Setup options are described in this section. The Advanced BIOS Setup screens are shown below. The sub menus are described on the following pages.
Figure 3.3 Advanced BIOS features setup screen
Launch PXE OpROM
This item allows users to enable or disable launch PXE OpROM if available.
Launch Storage OpROM
This item allows users to enable or disable launch storage OpROM if available.
3.4.1
Advantech BIOS Update V1.3
This item allows users to flash BIOS.
MIO-5250 User Manual 18
3.4.2
ACPI Settings
Figure 3.4 ACPI Setting
Enable ACPI Auto Configuration
This item allows users to enable or disable BIOS ACPI auto configuration.
Enable Hibernation
This item allows users to enable or disable hibernation.
ACPI Sleep State
This item allows users to set the ACPI sleep state.
Lock Legacy Resources
This item allows users to lock legacy devices' resources.
S3 Video Report
This item allows users to enable or disable S3 resume for VBIOS.
19 MIO-5250 User Manual
3.4.3
TPM Configuration
Figure 3.5 TPM Configuration
TPM Support
Disable/Enable TPM if available.
3.4.4
CPU Configuration
MIO-5250 User Manual
Figure 3.6 CPU Configuration
20
Hyper Threading Technology
This item allows users to enable or disable Intel Hyper Threading technology.
Execute Disable Bit
This item allows users to enable or disable the No-Execution page protection
Limit CPUID Maximum
This item allows users to enable or disable limit CPUID maximum for Windows
XP.
3.4.5
SATA Configuration
Figure 3.7 SATA Configuration
SATA Controller(s)
This item allows users to enable or disable the SATA controller(s).
SATA Mode Selection
This item allows users to select mode of SATA controller(s).
21 MIO-5250 User Manual
3.4.6
Intel Fast Flash Standby
Figure 3.8 Intel Fast Flash Standby
IFFS Support
This item allows users to enable or disable iFFS.
3.4.7
USB Configuration
MIO-5250 User Manual
Figure 3.9 USB Configuration
22
Legacy USB Support
Enable support for legacy USB. Auto option disables legacy support if no USB devices are connected.
EHCI Hand-Off
This is a workaround for the OS without EHCI hand-off support. The EHCI ownership change should claim by EHCI driver.
Port 60/64 Emulation
Enable or disable I/O port 60h/64h emulation support.
USB transfer time-out
Set the time-out value for Control, Bulk, and Interrupt transfers.
Device reset time-out
Set USB mass storage device Start Unit command time-out value.
Device power-up delay
Sets the maximum time the device will take before it properly reports itself to the
Host Controller. 'Auto' uses a default value: for a Root port it is 100 ms, for a
Hub port the delay is taken from the Hub descriptor.
3.4.8
Embedded Controller Configuration
Figure 3.10 Embedded Controller Configuration
EC iManager WatchDog IRQ
This item allows users to set the IRQ number of EC watchdog.
EC Power Saving Mode
This item allows users to set board's power saving mode when off.
Backlight Enable Polarity
This item allows users to set backlight enable polarity.
Backlight Mode
This item allows users to set backlight mode.
Backlight Mode 1
This item allows users to set backlight mode 1.
23 MIO-5250 User Manual
3.4.9
Super I/O Configuration
Figure 3.11 Super IO Configuration
Serial Port 0 Configuration
This item allows users to configure serial port 0.
Serial Port 1 Configuration
This item allows users to configure serial port 1.
Serial Port 2 Configuration
This item allows users to configure serial port 2.
Serial Port 3 Configuration
This item allows users to configure serial port 3.
MIO-5250 User Manual 24
3.4.10
AOAC Configuration
Figure 3.12 AOAC Configuration
AOAC Configuration
This item allows users to enable or disable AOAC function.
3.4.11
PPM Configuration
Figure 3.13 PPM Configuration
25 MIO-5250 User Manual
EIST
This item allows users to enable or disable Intel SpeedStep function.
CPU C state Report
This item allows users to enable or disable CPU C state report to OS.
Enhanced C state
This item allows users to enable or disable Enhanced CPU C state.
CPU Hard C4E
This item allows users to enable or disable CPU Hard C4E function.
CPU C6 state
This item allows users to enable or disable CPU C6 state.
C4 Exit Timing
This item allows users to control a programmable time for the CPU voltage to stabilize when exiting from a C4 state.
C-state POPDOWN
This item allows users to enable or disable Intel C-state POPDOWN function.
C-state POPUP
This item allows users to enable or disable Intel C-state POPUP function.
3.5
Chipset Configuration
Select the Chipset tab from the MIO-5250 setup screen to enter the Chipset BIOS
Setup screen. You can display a Chipset BIOS Setup option by highlighting it using the <Arrow> keys. All Plug and Play BIOS Setup options are described in this section.
The Plug and Play BIOS Setup screen is shown below.
MIO-5250 User Manual
Figure 3.14 Chipset Setup
26
3.5.1
Host Bridge/Intel IGD Configuration
Figure 3.15 Intel IGD Configuration
Auto Disable IGD
This item allows users to auto disable IGD upon external GFX detected.
IGFX - Boot Type*
This item allows users to select which output device during POST.
LCD Panel Type
This item allows users to select LCD panel by internal graphic device.
Panel Scaling
This item allows users to select LCD panel scaling by internal graphic device.
Active LFP*
This item allows users to select the active LFP configuration.
2nd LVDS Backlight Control
This item allows users to select 2nd backlight control.
IGD Clock Source
This item allows users to select IGD clock.
Fixed Graphics Memory Size
This item allows users to configure fixed graphic memory size.
ALS Support
This item allows users to select ASL support for ACPI.
*Since Intel Cedar Trail platform has some limitation on Display Combination (Refer to Boot Display Configuration on Intel
®
Atom
TM
Processor D2000 and N2000 Series
(Cedar Trail Platform), Application Note 513764), the following selection items need to match with below table as display device attached.
27 MIO-5250 User Manual
Boot type display
CRT
LFP(LVDS1)
EFP(HDMI)
EFP1(LVDS2)
CRT+LFP
CRT+EFP
CRT+EFP1
LFP+EFP
EFP+EFP1
Active_LFP
#No_LVDS
#INT-LVDS
#No_LVDS
#LVDS 2
#INT-LVDS
#No_LVDS
#LVDS 2
#INT-LVDS
#LVDS 2
NOTE
It only supports Graphic Mode under DOS environment.
EFP1 will be item "built-in display" in driver device list
Dual Display is only supported with Graphic Mode under DOS environment.
Dual Display is only supported with Graphic Mode under DOS environment.
Dual Display is only supported with Graphic Mode under DOS environment.
Dual Display is only supported with Graphic Mode under DOS environment.
In BIOS setup menu, it only has display on EFP1.
Dual Display is only supported with Graphic Mode under DOS environment.
3.5.2
South Bridge
Figure 3.16 South Bridge
MIO-5250 User Manual 28
Figure 3.17 TPT Device
Azalia Controller
Enables or disables the azalia controller.
Select USB Mode
Select USB mode by controllers or ports.
SMBus Controller
Enables or disables the onchip SMBus controller.
SIRQ Logic
Enables or disables the SIRQ logic.
SIRQ Mode
Set SIRQ mode.
MSATA/PCIe Switch
Enables for MSATA disables for PCIe.
LAN1/LAN2 Controller
This item allows users to enables or disables LAN device.
PCI Express PME
This item allows users to enables or disables PCIe PME function.
PCI Express Root Port 0/1
This item allows users to config PCIe port 0/1 settings.
DMI Link ASPM Control
This item Enables or disables control of active state power management on both
NB and SB side of DMI link.
High Precision Timer
Enables or disables the high precision timer.
SLP_S4 Assertion Width
This item allows users to set a delay of sorts.
Restore AC Power Loss
29 MIO-5250 User Manual
3.6
Boot Settings
Figure 3.18 Boot Setup Utility
Setup Prompt Timeout
This item allows users to select the number of seconds to wait for setup activation key.
Bootup NumLock State
Select the Power-on state for Numlock.
Quiet Boot
If this option is set to Disabled, the BIOS displays normal POST messages. If
Enabled, an OEM Logo is shown instead of POST messages.
Option ROM Message
Set display mode for option ROM.
Interrupt 19 Capture
This item allows option ROMs to trap interrupt 19.
1st/2nd/3rd/4th/5th/6th/7th Boot
This item allows users to set boot device priority.
MIO-5250 User Manual 30
3.7
Security Setup
Figure 3.19 Password Configuration
Select Security Setup from the MIO-5250 Setup main BIOS setup menu. All Security
Setup options, such as password protection is described in this section. To access the sub menu for the following items, select the item and press <Enter>:
Change Administrator / User Password
Select this option and press <ENTER> to access the sub menu, and then type in the password.
31 MIO-5250 User Manual
3.8
Save & Exit
Figure 3.20 Save & Exit
3.8.1
Save Changes and Exit
When users have completed system configuration, select this option to save changes, exit BIOS setup menu and reboot the computer if necessary to take effect of all system configuration parameters.
3.8.2
Discard Changes and Exit
Select this option to quit Setup without making any permanent changes to the system configuration.
3.8.3
Save Changes and Reset
When users have completed system configuration, select this option to save changes, exit the BIOS setup menu and reboot the computer to take effect of all system configuration parameters.
3.8.4
Discard Changes and Reset
Select this option to quit Setup without making any permanent changes to the system configuration and reboot the computer.
3.8.5
Save Changes
When users have completed system configuration, select this option to save changes without exiting the BIOS setup menu.
MIO-5250 User Manual 32
3.8.6
Discard Changes
Select this option to discard any current changes and load previous system configuration.
3.8.7
Restore Defaults
The MIO-5250 automatically configures all setup items to optimal settings when users select this option. Optimal Defaults are designed for maximum system performance, but may not work best for all computer applications. In particular, do not use the Optimal Defaults if the user's computer is experiencing system configuration problems.
3.8.8
Save User Defaults
When users have completed system configuration, select this option to save changes as user defaults without exit BIOS setup menu.
3.8.9
Restore User Defaults
The users can select this option to restore user defaults.
3.8.10
Boot Override
You select device you want to do boot override.
33 MIO-5250 User Manual
MIO-5250 User Manual 34
Chapter
4
MIOe Installation
4
The MI/O compact form factor SBC is a new-generation SBC design with a variety of mechanical improvements. Here is the quick installation guide for our thermal design and MIOe module installation.
Quick Installation Guide:
1.
There is a Heatsink / Cooler in the white box inside the package. Carefully remove the release paper from the thermal pad before installation.
Remove the release paper
2.
There are six screws inside the white box; please install DRAM in the SO-DIMM socket first, then screw the heatsink as shown below. Four long screws are for the heatsink; two shorter screws are for the main board.
3.
There are six standoff’s on the MIOe module which can also can be installed with the screws and copper studs.
MIO-5250 User Manual 36
Appendix
A
Pin Assignments
A
2
3
Pin
1
4
CN1
Part Number
Footprint
Description
12V Power Input
1655003865
WF_2x2P_165_BOX_RA_D_740SP
Pin Name
GND
GND
+12V
+12V
CN2
Part Number
Footprint
1
2
Description
Pin
DC JACK
1652005624
PJ_2P_2DC-G213B200
DC POWER JACK 2.5mm 90D(M) DIP 2DC-G213B200
Pin Name
+VIN
GND
CN3
Part Number
Footprint
Description
Pin
CN5
Part Number
Footprint
Description
Pin
1
2
SODIMMDDR3RVS_204
1651001648
DDR3_204P_2-2013311-1
DDR3 SODIMM H=9.2mm 204P SMD 2-2013311-1
Pin Name
Power Switch
1655302020
WF_2P_79_BOX_R1_D
WAFER BOX 2P 2.0mm 180D(M) DIP A2001WV2-2P
Pin Name
PSIN
GND
MIO-5250 User Manual 38
CN7
Part Number
Footprint
Description
Pin
1
2
Reset
1655302020
WF_2P_79_BOX_R1_D
WAFER BOX 2P 2.0mm 180D(M) DIP A2001WV2-2P
Pin Name
RESET#
GND
CN9
Part Number
Footprint
Description
5
6
3
4
Pin
1
2
7
8
9
10
GPIO
1653004099
HD_5x2P_79_23N685B-10M10
BOX HEADER 5x2P 2.00mm 180D(M) SMD 23N685B-10M10
Pin Name
+5V
GPIO4
GPIO0
GPIO5
GPIO1
GPIO6
GPIO2
GPIO7
GPIO3
GND
39 MIO-5250 User Manual
CN10
Part Number
Footprint
Description
12
13
14
15
8
9
10
11
6
7
4
5
2
3
Pin
1
VGA
1654000055
DBVGA-VF5MS
D-SUB Conn. 15P 90D(F) DIP 070242FR015S200ZU
GND
NC
GND
NC
DDAT
HSYNC
VSYNC
DCLK
Pin Name
RED
GREEN
BLUE
NC
GND
GND
GND
CN11
Part Number
Footprint
Description
PC7
PC8
PC9
PC10
PC11
PC12
Pin
PC1
PC2
PC3
PC4
PC5
PC6
MIO-5250 User Manual
CFast
1653004849
CFAST_24P_N7G24
CFast 24P 1.27mm 90D(M) SMD N7G24-A0B2RA-10-0HT-
GND
NC
NC
NC
NC
NC
Pin Name
CDI
GND
NC
NC
NC
NC
40
S4
S5
S6
S7
PC13
PC14
PC15
PC16
PC17
S1
S2
S3
+3.3V
+3.3V
GND
GND
CDO
GND
TX+
TX-
GND
RX-
RX+
GND
5
6
3
4
CN12
Part Number
Footprint
1
2
Description
Pin
SIM
1654000639
SIM-WL608C
SIM card conn 6p 90D(F)SMD WO/Pb WL608C3-M04-7F
Pin Name
UIM_PWR
UIM_RESET
UIM_CLK
GND
UIM_VPP
UIM_DATA
41 MIO-5250 User Manual
24
25
26
27
20
21
22
23
16
17
18
19
12
13
14
15
8
9
10
11
6
7
4
5
2
3
Pin
1
CN13
Part Number
Footprint
Description
40
41
42
43
36
37
38
39
32
33
34
35
28
29
30
31
MIO-5250 User Manual
Mini PCIE
1654006715
MINIPCI_52P_88911-5204M
SMB_DAT
PETp0
GND
GND
USB D-
GND
USB D+
+3.3VSB
GND
+3.3VSB
NC
GND
+VUIM_VPP
NC
GND
NC
NC
GND
PERST#
PERn0
+3.3VSB
PERp0
GND
GND
+1.5V
GND
SMB_CLK
PETn0
Pin Name
WAKE#
+3.3VSB
NC
GND
NC
+1.5V
MINI_CLKREQ#
+VUIM_PWR
GND
UIM_DATA
REFCLK-
UIM_CLK
REFCLK+
UIM_RESET
GND
42
48
49
50
51
44
45
46
47
52
H3
H4
H5
H6
NC
NC
NC
NC
+1.5V
NC
GND
NC
+3.3VSB
GND
GND
NC
NC
43 MIO-5250 User Manual
6
7
4
5
2
3
Pin
1
CN14
Part Number
Footprint
Description
SATA
1654004118
SATA_7P_50_WATA-07DPLH4U
Serial ATA 7P 1.27mm 90D(M) SMD WATA-07DPLH4U
Pin Name
GND
TX+
TX-
GND
RX-
RX+
GND
CN15
Part Number
Footprint
Description
2
3
Pin
1
4
SATA Power
1655001154
WF_4P_98_BOX_R1_D
WAFER BOX 4P 2.50mm 180D(M) DIP 24W1170-04S10-01
Pin Name
+5V
GND
GND
+12V
MIO-5250 User Manual 44
2
3
Pin
1
4
CN16
Part Number
Footprint
Description
USB3/4
1654009513
USB_8P_UB1112C-8FDE-4F
USB CONN. 8P 2.0mm 90D DIP UB1112C-8FDE-4F
Pin Name
+5V
D-
D+
GND
CN17
Part Number
Footprint
Description
6
7
4
5
8
9
2
3
Pin
1
Internal USB
1653005260
HD_5x2P_79_N10
PIN HEADER 2x5P 2.0mm 180D(M) SMD 21N22050
Pin Name
+5V
+5V
A_D-
B_D-
A_D+
B_D+
GND
GND
GND
Matching Cable: 1703100260 1703100121
45 MIO-5250 User Manual
2
3
Pin
1
4
CN18
Part Number
Footprint
Description
USB 1/2
1654009513
USB_8P_UB1112C-8FDE-4F
USB CONN. 8P 2.0mm 90D DIP UB1112C-8FDE-4F
Pin Name
+5V
D-
D+
GND
CN19
Part Number
Footprint
Description
12
13
14
15
8
9
10
11
16
17
18
19
20
6
7
4
5
2
3
Pin
1
COM1/COM2 RS-232
1653004793
HD_10x2P_79_23N685B-20M10
BOX HEADER 10x2P 2.0mm 180D(M)SMD 23N685B-20M10B
RI1#
GND
GND
DCD2#
DSR2#
RXD2
RTS2#
TXD2
Pin Name
DCD1#
DSR1#
RXD1
RTS1#
TXD1
CTS1#
DTR1#
CTS2#
DTR2#
RI2#
GND
GND
MIO-5250 User Manual 46
Matching Cable: 1701200220
CN20
Part Number
Footprint
Description
Pin
1
2
3
4
5
RS422/485 1
1655304032
WF_5P_49_BOX_85205
WAFER 5P 1.25mm 180D(M) SMD 85205-05701
Pin Name
422RX-
422RX+
422/485TX+
422/485TX-
GND
47 MIO-5250 User Manual
CN22
Part Number
Footprint
Description
2
3
Pin
1
4
5
RS422/485 2
1655304032
WF_5P_49_BOX_85205
WAFER 5P 1.25mm 180D(M) SMD 85205-05701
Pin Name
422RX-
422RX+
422/485TX+
422/485TX-
GND
CN24
Part Number
Footprint
Description
11
12
13
14
7
8
9
10
15
16
17
18
19
5
6
3
4
Pin
1
2
MIO-5250 User Manual
COM3/COM4 RS-232
1653004793
HD_10x2P_79_23N685B-20M10
BOX HEADER 10x2P 2.0mm 180D(M)SMD 23N685B-20M10B
Pin Name
DCD3#
DSR3#
RXD3
RTS3#
TXD3
CTS3#
DTR3#
RI3#
GND
GND
DCD4#
DSR4#
RXD4
RTS4#
TXD4
CTS4#
DTR4#
RI4#
GND
48
20 GND
Matching Cable: 1701200220
CN25
Part Number
Footprint
Description
3
4
Pin
1
2
SMBus
1655904020
FPC4V-125M
WAFER 4P 1.25mm 180D(M) SMD 85205-04001
Pin Name
GND
SMB_DAT
SMB_CLK
+5V
CN26
Part Number
Footprint
Description
Pin
1
2
3
System FAN
1655003010
WHP3VA
Wafer 2.54mm 3P 180D(M) DIP W/LOCK 22-27-2031
Pin Name
GND
+12V
Speed
49 MIO-5250 User Manual
CN28
Part Number
Footprint
Description
6
7
4
5
8
2
3
Pin
1
LAN
1652003274
RJ45_28P_RTB-19GB9J1A
PHONE JACK RJ45 28P DIP RTB-19GB9J1A
Pin Name
TX+(10/100), BI_DA+(GHz)
TX-(10/100), BI_DA-(GHz)
RX+(10/100), BI_DB+(GHz)
BI_DC+(GHz)
BI_DC-(GHz)
RX-(10/100), BI_DB-(GHz)
BI_DD+(GHz)
BI_DD-(GHz)
CN30
Part Number
Footprint
Description
8
9
10
6
7
4
5
2
3
Pin
1
Audio
1653004099
HD_5x2P_79_23N685B-10M10
BOX HEADER 5x2P 2.00mm 180D(M) SMD 23N685B-10M10
Pin Name
LOUTR
LINR
GND
GND
LOUTL
LINL
GND
GND
MIC1R
MIC1L
Matching Cable: 1703100152
MIO-5250 User Manual 50
CN31
Part Number
Footprint
Description
28
29
30
31
24
25
26
27
20
21
22
23
16
17
18
19
36
37
38
39
32
33
34
35
40
41
12
13
14
15
8
9
10
11
6
7
4
5
2
3
Pin
1
MIOe
1654006235
BB_40x2P_32_1625x285_2HOLD
PCIE_TX2+
PCIE_RX2-
PCIE_TX2-
GND
GND
PCIE_RX3+
PCIE_TX3+
PCIE_RX3-
PCIE_TX3-
GND
GND
PCIE_CLK+
LOUTL
PCIE_CLK-
LOUTR
GND
Pin Name
GND
GND
PCIE_RX0+
PCIE_TX0+
PCIE_RX0-
PCIE_TX0-
GND
GND
PCIE_RX1+
PCIE_TX1+
PCIE_RX1-
PCIE_TX1-
GND
GND
PCIE_RX2+
AGND
SMB_CLK
NC
SMB_DAT
NC
PCIE_WAKE#
NC
RESET#
NC
SLP_S3#
51 MIO-5250 User Manual
70
71
72
73
66
67
68
69
62
63
64
65
58
59
60
61
54
55
56
57
50
51
52
53
46
47
48
49
42
43
44
45
88
89
90
84
85
86
87
78
79
80
83
74
75
76
77
MIO-5250 User Manual
CLK33M
SLP_S5#
LPC_AD0
DDP_HPD
LPC_AD1
GND
LPC_AD2
DDP_AUX+
LPC_AD3
DDP_AUX-
LPC_DRQ#0
GND
LPC_SERIRQ
DDP_D0+
LPC_FRAME#
DDP_D0-
GND
GND
USB0_D+
DDP_D1+
USB0_D-
DDP_D1-
GND
GND
USB1_D+/USB_SSTX+
DDP_D2+
USB1_D-/USB_SSTX-
DDP_D2-
GND
GND
USB2_D+/USB_SSRX+
DDP_D3+
USB2_D-/USB_SSRX-
DDP_D3-
GND
GND
USB_OC#
+12VSB
NC
GND
GND
GND
GND
+5VSB
+5VSB
+5VSB
+5VSB
52
8
9
10
11
6
7
4
5
2
3
Pin
1
CN33
Part Number
Footprint
Description
24 bits LVDS1 Panel
1653910261
SPH10X2
B/B Conn 10x2P 1.25mm 180D(M)SMD DF13-20DP-1.25V
Pin Name
GND
GND
LVDS0_D0+
NC
LVDS0_D0-
NC
LVDS0_D1+
NC
LVDS0_D1-
NC
LVDS0_D2+
53 MIO-5250 User Manual
16
17
18
19
20
12
13
14
15
NC
LVDS0_D2-
NC
LVDS0_CLK+
LVDS0_D3+
LVDS0_CLK-
LVDS0_D3-
+5V or +3.3V
+5V or +3.3V
3
4
5
CN34
Part Number
Footprint
1
2
Description
Pin
48 bits LVDS2 Inverter Power
1655000453
WHL5V-2M-24W1140
WAFER BOX 2.0mm 5P 180D(M) DIP WO/Pb JIH VEI
Pin Name
+12V
GND
ENABKL
VBR
+5V
MIO-5250 User Manual 54
32
33
34
35
28
29
30
31
36
37
38
39
40
24
25
26
27
20
21
22
23
16
17
18
19
12
13
14
15
8
9
10
11
6
7
4
5
2
3
Pin
1
CN35
Part Number
Footprint
Description
GND
LVDS0_D1-
LVDS1_D1-
LVDS0_D1+
LVDS1_D1+
GND
GND
LVDS0_D2-
LVDS1_D2-
LVDS0_D2+
LVDS1_D2+
GND
GND
LVDS0_CLK-
LVDS1_CLK-
LVDS0_CLK+
48 bits LVDS2 Panel
1653920200
SPH20X2
B/B Conn. 40P 1.25mm 90D SMD DF13-40DP-1.25V(91)
Pin Name
+5V or +3.3V
+5V or +3.3V
GND
GND
+5V or +3.3V
+5V or +3.3V
LVDS0_D0-
LVDS1_D0-
LVDS0_D0+
LVDS1_D0+
GND
LVDS1_CLK+
GND
GND
NC
NC
GND
GND
LVDS0_D3-
LVDS1_D3-
LVDS0_D3+
LVDS1_D3+
NC
NC
55 MIO-5250 User Manual
CN36
Part Number
Footprint
Description
12
13
14
15
8
9
10
11
16
17
18
19
6
7
4
5
2
3
Pin
1
HDMI
1654009225
HDMI_19P_QJ51193-FFD4-7F
HDMI Conn 19P 0.5mm 90D(M) SMD QJ51193-FFB4-7F
Pin Name
TMDS Data2+
TMDS Data2 Shield
TMDS Data2®C
TMDS Data1+
TMDS Data1 Shield
TMDS Data1®C
TMDS Data0+
TMDS Data0 Shield
TMDS Data0®C
TMDS Clock+
TMDS Clock Shield
TMDS Clock®C
Reserved
Reserved
SCL
SDA
DDC Ground
+5V Power
Hot Plug Detect
MIO-5250 User Manual 56
16
17
18
19
20
12
13
14
15
8
9
10
11
6
7
4
5
2
3
Pin
1
CN37
Part Number
Footprint
Description
D3-
D0+
D3+
GND
NC
D1-
GND
D1+ eDP
1653910261
SPH10X2
B/B Conn 10x2P 1.25mm 180D(M)SMD DF13-20DP-1.25V
Pin Name
GND
GND
D0-
SDAT
GND
SCLK
D2-
GND
D2+
Hot Plug Detect
+5V or +3.3V
+5V or +3.3V
57 MIO-5250 User Manual
4
5
2
3
Pin
1
CN38
Part Number
Footprint
Description
24 bits LVDS1 Inverter Power
1655000453
WHL5V-2M-24W1140
WAFER BOX 2.0mm 5P 180D(M) DIP WO/Pb JIH VEI
Pin Name
+12V
GND
ENABKL
VBR
+5V
MIO-5250 User Manual 58
Appendix
B
B
System Assignments
B.1
System I/O Ports
Table B.1: System I/O Ports
Addr. Range (Hex)
000-01F
20h-2Dh
50h-52h
060-06F
070-07F
080-09F
0A0-0BF
0C0-0DF
170h-177h
1F0h-1F7h
299h-29Ah
29Ch-29Dh
2E8-2EF
2F8-2FF
3E8-3EF
3F8-3FF
0400 - 04FF
0500 - 053F
Device
DMA Controller
Interrupt Controller
Timer/Counter
8042 (keyboard controller)
Real-time clock, non-maskable interrupt (NMI)mask
DMA page register
0A0-0BF
DMA controller
IDE Controller
IDE Controller
EC HM Index port and Data port
EC Index port and Data port
Communications Port (COM4)
Communications Port (COM2)
Communications Port (COM3)
Communications Port (COM1)
Motherboard resources
Motherboard resources
B.2
DMA Channel assignments
Table B.2: DMA Channel assignments
Channel
6
7
4
5
2
3
0
1
Function
Available
Available
Available
Available
Direct memory access controller
Available
Available
Available
MIO-5250 User Manual 60
B.3
1st MB memory map
Table B.3: 1st MB memory map
Addr. Range (Hex)
E0000h - FFFFFh
D0000h - DFFFFh
C0000h - CFFFFh
A0000h - BFFFFh
A0000h - BFFFFh
00000h - 9FFFFh
Device
System board
PCI Bus
System board
PCI Bus
Intel® HD Graphic
System board
B.4
Interrupt assignments
Table B.4: Interrupt assignments
Interrupt#
IRQ7
IRQ8
IRQ9
IRQ10
IRQ11
IRQ12
IRQ13
IRQ14
IRQ15
NMI
IRQ0
IRQ1
IRQ2
IRQ3
IRQ4
IRQ5
IRQ6
Interrupt source
Parity error detected
System timer
Standard 101/102-Key or Microsoft Natural PS/2 Keyboard
Interrupt from controller 2 (cascade)
Communications Port (COM2)
Communications Port (COM1)
EC Watch DOG
Available
Communications Port (COM3)
System CMOS/real time clock
Microsoft ACPI-Compliant System
Available
Communications Port (COM4)
PS/2 Compatible Mouse
Numeric data processor
Primary IDE
Secondary IDE
61 MIO-5250 User Manual
MIO-5250 User Manual 62
Appendix
C
Watchdog Timer
Sample Code
C
C.1
EC Watchdog Timer sample code
EC_Command_Port = 0x29Ah
EC_Data_Port = 0x299h
Write EC HW ram = 0x89
Watch dog event flag = 0x57
Watchdog reset delay time = 0x5E
Reset event = 0x04
Start WDT function = 0x28
====================================================
.model small
.486p
.stack 256
.data
.code
org 100h
.STARTup
mov dx, EC_Command_Port mov al,89h ; Write EC HW ram.
out dx,al mov dx, EC_Command_Port mov al, 5Fh ; Watchdog reset delay time low byte (5Eh is high byte) index.
out dx,al mov dx, EC_Data_Port mov al, 30h ;Set 3 seconds delay time.
out dx,al mov dx, EC_Command_Port mov al,89h ; Write EC HW ram.
out dx,al mov dx, EC_Command_Port mov al, 57h ; Watch dog event flag.
out dx,al mov dx, EC_Data_Port mov al, 04h ; Reset event.
out dx,al mov dx, EC_Command_Port mov al,28h ; start WDT function.
out dx,al
.exit
END
MIO-5250 User Manual 64
65 MIO-5250 User Manual
www.advantech.com
Please verify specifications before quoting. This guide is intended for reference purposes only.
All product specifications are subject to change without notice.
No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permission of the publisher.
All brand and product names are trademarks or registered trademarks of their respective companies.
© Advantech Co., Ltd. 2013
advertisement
Key Features
- Intel® Atom™ N2600/D2550 processor
- Dual displays
- Up to 4GB DDR3
- 6 USB2.0
- SATAII (300 MBs)
- 2 GbE
- CFast
- MIOe support
- Flexible storage
