QUICK GUIDE AXIS M50 Series

QUICK GUIDE
AXIS M50 Series
AXIS M5013 PTZ Dome Network Camera
AXIS M5014 PTZ Dome Network Camera
Legal Considerations
Video and audio surveillance can be prohibited
by laws that vary from country to country. Check
the laws in your local region before using this
product for surveillance purposes. This product
includes one (1) H.264 decoder license. To purchase further licenses, contact your reseller.
Trademark Acknowledgments
Apple, Boa, Bonjour, Ethernet, Internet Explorer,
Linux, Microsoft, Mozilla, Real, SMPTE, QuickTime, UNIX, Windows, Windows Vista and WWW
are registered trademarks of the respective
holders. Java and all Java-based trademarks and
logos are trademarks or registered trademarks
of Oracle and/or its affiliates. UPnPTM is a
certification mark of the UPnPTM Implementers
Corporation.
Electromagnetic Compatibility (EMC)
This equipment has been designed and tested to
fulfill applicable standards for:
• Radio frequency emission when installed
according to the instructions and used in its
intended environment.
• Immunity to electrical and electromagnetic
phenomena when installed according to the instructions and used in its intended environment.
USA - This equipment has been tested using
shielded cables (STP) and found to comply with
the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses
and can radiate radio frequency energy and, if
not installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is encouraged
to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
Canada - This Class A digital apparatus complies
with Canadian ICES-003.
Europe This digital equipment fulfills
the requirements for RF emission according to
the Class A limit of EN 55022. NOTICE! This is a
Class A product. In a domestic environment this
product may cause RF interference, in which case
the user may be required to take adequate measures. This product fulfills the requirements for
immunity according to EN 61000-6-1 residential,
commercial and light-industry environments. This
product fulfills the requirements for immunity
according to EN 61000-6-2 industrial environments. This product fulfills the requirements
for immunity according to EN 55024 office and
commercial environments.
Australia - This digital equipment fulfills the
requirements for RF emission according to the
Class A limit of AS/NZS CISPR 22. NOTICE! This
is a class A product. In a domestic environment
this product may cause RF interference, in which
case the user may be required to take adequate
measures.
Korea - 이 기기는 업무용(A급) 전자파적합기기로
서 판매자 또는 사용자는 이 점을 주의하시기 바
라며, 가정외의 지역에서 사용하는 것을 목적으
로 합니다.
Japan - この装置は、クラスB 情報技術装置です。この
装置は、家庭環境で使用することを目 的としています
が、
この装置がラジオやテレビジョン受信機に近接し
て使用されると、受信障害を引き起こすことがありま
す。取扱説明書に従って正しい取り扱いをして下さい。
Safety
This product complies to EN/IEC 60950-1, Safety
of Information Technology Equipment.
Equipment Modifications
This equipment must be installed and used in
strict accordance with the instructions given in
the user documentation. This equipment contains
no user-serviceable components. Unauthorized equipment changes or modifications will
invalidate all applicable regulatory certifications
and approvals.
Liability
Every care has been taken in the preparation
of this document. Please inform your local Axis
office of any inaccuracies or omissions. Axis
Communications AB cannot be held responsible
for any technical or typographical errors and reserves the right to make changes to the product
and documentation without prior notice.
Axis Communications AB makes no warranty of
any kind with regard to the material contained
within this document, including, but not limited
to, the implied warranties of merchantability and
fitness for a particular purpose. Axis Communications AB shall not be liable nor responsible for
incidental or consequential damages in connection with the furnishing, performance or use of
this material. This product is only to be used for
its intended purpose.
RoHS
This product complies with both the
European RoHS directive, 2002/95/EC, and the
Chinese RoHS regulations, ACPEIP.
WEEE Directive
The European Union has enacted a Directive 2002/96/EC on Waste Electrical and
Electronic Equipment (WEEE Directive).
This directive is applicable in the European
Union member states. The WEEE marking on
this product (see right) or its documentation
indicates that the product must not be disposed
of together with household waste. To prevent
possible harm to human health and/or the
environment, the product must be disposed of in
an approved and environmentally safe recycling
process. For further information on how to
dispose of this product correctly, contact the
product supplier, or the local authority responsible for waste disposal in your area. Business
users should contact the product supplier for
information on how to dispose of this product
correctly. This product should not be mixed with
other commercial waste.
Support
Should you require any technical assistance,
please contact your Axis reseller. If your questions cannot be answered immediately, your
reseller will forward your queries through the
appropriate channels to ensure a rapid response.
If you are connected to the Internet, you can:
• download user documentation and firmware
updates
• find answers to resolved problems in the FAQ
database. Search by product, category, or
phrases
• report problems to Axis support by logging in to
your private support area
Safeguards
• Store the Axis product in a dry and ventilated
environment.
• Avoid exposing the Axis product to vibration,
shocks or heavy pressure. Do not install the
product on unstable brackets, unstable or vibrating surfaces or walls, since this could cause
damage to the product.
• Only use applicable tools when installing the
Axis product; excessive force could cause damage to the product.
• Do not use chemicals, caustic agents, or aerosol
cleaners. Use a damp cloth for cleaning.
• Use only accessories that comply with technical
specification of the product. These can be
provided by Axis or a third party.
• Use only spare parts provided by or recommended by Axis.
• Do not attempt to repair the product by
yourself, contact Axis or your Axis reseller for
service matters.
• This Axis product shall be used in compliance
with local laws and regulations.
Transportation
• When transporting the Axis product, use the
original packaging or equivalent to prevent
damage to the product.
Battery Replacement
This Axis product uses a 3.0 V CR2032 lithium
battery as the power supply for its internal
real-time clock (RTC). Under normal conditions
this battery will last for a minimum of 5 years.
Low battery power affects the operation of the
RTC, causing it to reset at every power-up. A
log message will appear when the battery needs
replacing. The battery should not be replaced
unless required!
If the battery does need replacing, please contact
www.axis.com/techsup for assistance.
• Dispose of used batteries according to the
manufacturer’s instructions.
• Risk of explosion if battery is incorrectly
replaced.
• Replace only with the same or equivalent battery, as recommended by the manufacturer.
Power Requirements
Power over Ethernet, IEEE 802.3af class 3,
44 – 57 V DC max 12.95 W
Dome Cover Cleaning
• Be careful not to scratch or damage the dome
cover. Do not clean a dome cover that looks
clean to the eye and never polish the surface.
Excessive cleaning could damage the surface.
• For general cleaning of a dome cover it is recommended to use a non-abrasive, solvent-free
neutral soap or detergent with water and a soft
cloth. Rinse well with clean lukewarm water. Dry
with a soft cloth to prevent water spotting.
• Never use harsh detergents, gasoline, benzene
or acetone etc. and avoid cleaning in direct
sunlight or at elevated temperatures.
4
AXIS M50 Series
1x
1x
1x
1x
1 YEAR LIMITED HARDWARE WARRANTY
Warranty Coverage
Axis Communications AB’s (“Axis”) warranty obligations are limited to the terms set forth below:
Axis warrants the original purchaser that the AXIS Network Video product enclosed with this limited hardware warranty will in
respect of the hardware be free from defects in design, workmanship and materials under normal use for a period of one (1) year from
the date of the original end-user purchase (“Warranty Period”).
Notwithstanding the above the Warranty Period shall be limited to a period of three (3) months from the date of the original end-user
purchase for PTZ Network Cameras (not including Dome Network Cameras) which are at any time used in continuous motion
applications (i.e. sequence mode and guard tour). For avoidance of doubt, if said products are not at any time used in continuous
motion applications, the original hardware warranty of one (1) year will apply.
Camera owner authentication key
The original purchaser shall without undue delay notify Axis of any defect which appears according to Axis’ RMA Handling, failure
to which shall mean that the purchaser loses its right to have the defect remedied. A valid form of a bill of sale or receipt from an
authorized retailer/distributor with the date of the original purchase must be presented to obtain warranty service. If a valid claim is
received within the Warranty Period, the sole remedy of the original purchaser and Axis’ sole and exclusive liability shall be limited
to, at Axis sole discretion, either repair of the hardware defect using new or refurbished replacement parts, or replacement of the
product. Repaired or replacement hardware will be warranted for the remainder of the original Warranty Period or ninety (90) days,
whichever is longer. When a product or part is exchanged the replacement hardware becomes the property of the original purchaser
and all hardware or part thereof that is replaced shall become the property of Axis.
The authentication key on this label is used to authenticate the owner/administrator of this Axis
Warranty
is applicable
camera. The key is associated with the camera’s unique serial numberThis
(S/N),Limited
as shown
at the top
of the in all countries and may be enforced by contacting Axis support worldwide, for more
please
visit our
site www.axis.com
label. The authentication key is used for registering the camera with aninformation
AVHS service
provider
forweb
hosted
video. For more information and help to find a local AVHS Service Provider, go to:
Exclusions and Limitations
This warranty does not apply (a) to faulty and improper installation, maintenance, service, repair and/or alteration in any way that is
not contemplated in the documentation for the product or carried out with Axis’ consent in writing, operational adjustments covered
http://www.axis.com/products/avhs/ in the operating manual for the product or normal maintenance, (b) to cosmetic damages, (c) if the product is modified or tampered
with, (d) if the product is damaged by acts of God, misuse, abuse, negligence, accident, normal wear and tear and deterioration,
Please retain this document for future reference.
improper environmental conditions (including, but not limited to, electrical surges, water damage and heat exposure) or lack of
responsible care, (e) if the product has had the model or serial number altered, defaced or removed, (f) to consumables (such as
batteries) (g) to products that have been purchased “as is” and Axis, the seller or the liquidator expressly disclaim their warranty
obligation pertaining to the product, (h) to any non-Axis hardware product or any software (irrespective of packaged or sold with an
Axis hardware product) and Axis products purchased from an unauthorized distributor/reseller,(i) to damage that occurs in shipment
or (j) to damages by any other causes not related to defective design, workmanship and/or materials.
Label here
NOTE:
•
If the product is to be used outdoors or in dusty, humid, or other hostile environments, it must be suitably protected.
•
Further, camera products specifically, must be protected, whether in use or not, from exposure to direct sunlight or halogen
light – which may damage the camera image sensor. This applies to both indoor and outdoor use of the cameras.
•
For camera products supplied without a lens, extreme care should be used when mounting a lens on these products. Damage to
the product due to incorrectly mounted lenses will invalidate this limited hardware warranty.
•
Failure to comply with any of the aforementioned requirements will invalidate this Limited Hardware Warranty.
THE WARRANTY AND REMEDIES PROVIDED ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS OR IMPLIED
WARRANTIES INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. CERTAIN JURISDICTIONS DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES. IF LAWS
UNDER SUCH JURISDICTIONS APPLY, THEN ALL EXPRESS AND IMPLIED WARRANTIES ARE LIMITED TO THE WARRANTY
PERIOD IDENTIFIED ABOVE. UNLESS PROVIDED HEREIN, ANY STATEMENTS OR REPRESENTATIONS MADE BY ANY OTHER
PERSON OR FIRM ARE VOID. EXCEPT AS PROVIDED IN THIS WRITTEN WARRANTY AND TO THE EXTENT PERMITTED BY LAW,
NEITHER AXIS NOR ANY AFFILIATES SHALL BE LIABLE FOR ANY LOSS, (INCLUDING LOSS OF DATA AND INFORMATION),
INCONVENIENCE, OR DAMAGE, INCLUDING, BUT NOT LIMITED TO, DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES, RESULTING FROM THE USE OR INABILITY TO USE THE AXIS PRODUCT, WHETHER RESULTING FROM BREACH OF
WARRANTY OR ANY OTHER LEGAL THEORY. NOTWITHSTANDING THE FOREGOING, AXIS’ TOTAL LIABILITY FOR ALL
CLAIMS UNDER THIS WARRANTY SHALL NOT EXCEED THE PRICE PAID FOR THE PRODUCT. THESE LIMITATIONS ON
POTENTIAL LIABILITIES HAVE BEEN AN ESSENTIAL CONDITION IN SETTING THE PRODUCT PRICE.
Applicable Law
•
This Limited Warranty is governed by and construed under the laws of Sweden.
This Limited Hardware Warranty may be subject to Axis’ change at any time without prior notice.
•
©2006-2010 Axis Communications AB.
Axis is a registered trademark. All other company names and products are
trademarks or registered trademarks of their respective companies. We
reserve the right to introduce modifications without notice.
Part No. 38655
1Yr Warranty Sheet – Video
1x
2x
1x
March 2007
Rev. 4.00
Part no. 28801
1x
AXIS M50 Series
5
AXIS XXX
P/N: XXX
S/N: XXX
This device co
Operation is s
(1) this device
(2) this device
interference t
This Class B d
N1
AXIS XXXXX
P/N: XXXX-X
S/N: XXXXXX
This device compli
Operation is subjec
(1) this device may
(2) this device mus
interference that m
This Class B digita
N1202
AXIS XXXXX
P/N: XXXX X
AXIS XXXXX
P/N: XXXX-X
S/N: XXXXXX
This device compli
Operation is subje
(1) this device may
(2) this device mus
interference that m
This Class B digita
N1202
AXIS XXXXX
P/N: XXXX X
6
AXIS M50 Series
0°
-180°
+180°
7
10
AXIS M50 Series
1
2
7
8
AXIS M50 Series
3
4
AXIS M50 Series
9
10
1
2
AXIS M50 Series
AXIS M50 Series
3
4
11
12
AXIS M50 Series
5
AXIS M50 Series
6
13
Quick Guide
AXIS M50 Series
© Axis Communications AB, 2011-2012
Ver.1.1
Printed: April 2012
Part No. 47254