McQuay ACZ 055A Operating instructions

Installation and Maintenance Manual
IMM ACZ/AGZ-4
Group: Chiller
Part Number: 331374201
Effective: October 2006
Supersedes: August 2006
Air-Cooled Scroll Condensing Units
ACZ 030B through 155B
Air-Cooled Scroll Chillers w/ Remote Evaporators
AGZ 026BM through 130BM
60 Hertz, R-22, R 407C
Table of Contents
Introduction.................................................... 3
General Description.....................................................3
Inspection ....................................................................3
Nomenclature ..............................................................3
Installation...................................................... 4
Handling ......................................................................4
Location.......................................................................5
Sound Isolation..........................................................12
Vibration Isolators .....................................................12
Ambient Temperature and Water Flow Limitations...14
Water Piping (Model AGZ-BM)................................14
ACZ Staging and Circuiting ......................................21
Remote Evaporator Refrigerant Piping .....................22
Chilled Water Flow Switch........................................24
Evaporator Flow and Pressure Drop..........................25
Wind Baffles and Hail Guards...................................26
Physical Data ................................................ 28
Electrical Data Standard Ambient ............. 33
Electrical Data High Ambient..................... 43
Dimensional Data ......................................... 52
Pre Start-up................................................................59
Start-Up .....................................................................59
Shutdown...................................................................60
Water Piping Checkout..............................................60
Refrigerant Piping Checkout .....................................60
Electrical Check Out .................................................61
Operation ...................................................... 61
Hot Gas Bypass (Optional)........................................61
VFD Low Ambient Control (Optional) .....................62
Filter-Driers (AGZ-BM)............................................62
System Adjustment....................................................62
Liquid Line Sight Glass and Moisture Indicator .......62
Refrigerant Charging.................................................62
Thermostatic Expansion Valve ..................................62
Crankcase Heaters .....................................................63
Unit Maintenance......................................... 64
Preventive Maintenance Schedule.............................65
Service ........................................................... 66
Liquid Line Solenoid Valve.......................................66
Remote Evaporator (AGZ-BM Only) .......................67
Refrigerant Charging.................................................67
Remote Evaporators ..................................................55
Warranty Statement .................................... 68
Optional Features......................................... 56
ACZ/AGZ Troubleshooting Chart ............. 69
Start-up ......................................................... 59
Unit controllers are LONMARK
certified with an optional
LONWORKS communication
Manufactured in an ISO Certified facility
"McQuay" is a registered trademark of McQuay International
©2004 McQuay International
Illustrations and data cover McQuay International products at the time of publication and we reserve the right
to make changes in design and construction at anytime without notice.
2
ACZ / AGZ-BM
IMM ACZ/AGZ-4
Introduction
General Description
This manual covers two similar product lines:
AGZ-BM, Packaged chiller with the evaporator shipped separately for remote installation, field
piping to the outdoor unit, and interconnection of wiring. The refrigeration specialties are shipped
from the factory for field installation.
Operating instructions are contained in operating manual OM AGZ.
ACZ-BC, Condensing unit with no evaporator included. For use with customer supplied low side
(usually an air-handling unit), field piped and wired to the condensing unit.
Operating instructions are contained in operating manual OM ACZ.
These McQuay air-cooled units are complete, self-contained, automatic refrigerating units. Every
unit is completely assembled, factory wired, tested and provided with a holding charge. Each unit
consists of two air-cooled condenser sections with integral subcooler sections, two tandem or triple
scroll compressors, (brazed-plate or replaceable tube, dual circuit shell-and-tube evaporator and
liquid line components including manual, sight-glass/moisture indicators, solenoid valves, and
thermal expansion valves on AGZ-BM only). Other features include compressor crankcase heaters,
an evaporator heater for chilled water freeze protection (on AGZ-BM only), one-time pumpdown
during “on” or “off” periods, and automatic compressor lead-lag to alternate the compressor starting
sequence.
The electrical control center includes all equipment protection and operating controls necessary for
dependable automatic operation. Condenser fan motors are protected in all three phases and started
by their own three-pole contactors. Model ACZ condensing units require a field-supplied multi-step
thermostat wired to the outdoor unit.
Inspection
Check all items carefully against the bill of lading. Inspect all units for damage upon arrival. Report
shipping damage and file a claim with the carrier. Check the unit nameplate before unloading,
making certain it agrees with the power supply available. McQuay is not responsible for physical
damage after unit leaves the factory.
Note: Unit shipping and operating weights are available in the Physical Data tables
beginning on page 28.
Nomenclature
A G Z - XXX B M
Application
C= Condensing Unit
M= Remote Evaporator
Air-Cooled
IMM ACZ/AGZ-4
G=Global Chiller
C=Condensing Unit
Design Vintage
Scroll Compressor
Model Size
(Nominal Tons)
ACZ / AGZ-BM
3
Installation
Note: Installation is to be performed by qualified personnel who are familiar with local
codes and regulations.
WARNING
Sharp edges on unit and coil surfaces are a potential hazard to personal safety. Avoid
contact with them.
Handling
Be careful to avoid rough handling of the unit. Do not push or pull the unit from anything other than
the base. Block the pushing vehicle away from the unit to prevent damage to the sheet metal cabinet
and end frame (see Figure 1).
To lift the unit, 2 1/2" (64mm) diameter lifting tabs are provided on the base of the unit. Arrange
spreader bars and cables to prevent damage to the condenser coils or cabinet (see Figure 2).
Figure 1, Suggested Pushing Arrangement
Blocking is required
across full width
Figure 2, Suggested Lifting Arrangement
Spreader bars
required
(use caution)
Number of fans may vary
from this diagram. The lifting
method will remain the same.
All rigging locations
must be used.
4
ACZ / AGZ-BM
IMM ACZ/AGZ-4
Location
Figure 3, Clearances
Unit Placement
ACZ/AGZ units are for outdoor applications and can
be mounted either on a roof or at ground level. For
roof mounted applications, install the unit on a steel
channel or I-beam frame to support the unit above the
roof. For ground level applications, install the unit on
a substantial base that will not settle. A one-piece
concrete slab with footings extended below the frost
line is recommended. Be sure the foundation is level
within 1/2"(13mm) over its length and width. The
foundation must be strong enough to support the
weights listed in the Physical Data Tables beginning
on page 28.
SEE TABLE BELOW
DIMENSION “A”
4 FT. (1220mm)
CLEARANCE FOR
SERVICE ACCESS
4 FT. (1220)
CLEARANCE FOR
SERVICE ACCESS
SEE TABLE BELOW
DIMENSION “A”
Table 1, Recommended Minimum Clearances
ACZ-BC
Model Sizes
030B – 080B
090B – 155B
AGZ-BM
Model Size
026B – 070B
075B – 130B
Coil Side “A”
ft (m)
4 (1.2)
6 (1.8)
“B”
ft (m)
8 (2.4)
12 (3.6)
“C”
ft (m)
6 (1.8)
8 (2.4)
End Opposite
Controls ft (m)
4 (1.2)
4 (1.2)
Control Panel End
ft. (m)
4 (1.2)
4 (1.2)
Clearances
Do not block the flow of air to and
from the condenser coil. Restricting
airflow or allowing air recirculation
will result in a decrease in unit
performance and efficiency because
discharge pressures are increased.
There must be no obstruction above
the unit that would deflect discharge
air downward where it could be
recirculated back to the inlet of the
condenser coil. The condenser fans are
propeller type and will not operate
with ductwork.
Install the unit with enough side
clearance for air entrance to the coil
and for servicing. Provide service
access to the evaporator, compressors,
electrical control panel and piping
components.
Do not allow debris to accumulate
near the unit where it could be drawn
into the condenser coil.
Keep
condenser coils and fan discharge free
of snow or other obstructions to permit
adequate airflow for proper operation.
IMM ACZ/AGZ-4
AIR
DISCHARGE
AIR
DISCHARGE
AIR FLOW
AIR FLOW
AIR FLOW
“B”
The recommended minimum side clearance between two units
is dimension “B’ in table on this page.
AIR
DISCHARGE
AIR FLOW
AIR FLOW
“C”
“C”
The unit must not be installed in a pit or enclosure that is
deeper or taller than the height of the unit unless extra space
is provided. The minimum clearance on each
side of the unit is dimension “C” in table on this page.
ACZ / AGZ-BM
5
Restricted Air Flow
General
The clearances required for design-life operation of ACZ/AGZ air-cooled units are described in the
previous section. Occasionally, these clearances cannot be maintained due to site restrictions, such
as units being too close together, or a fence or wall restricting airflow, or both.
The McQuay ACZ/AGZ units have several features that can mitigate the problems attributable to
restricted airflow.
•
The condenser section is configured as shown below. This configuration allows inlet air for
these coils to come in from either side. A vertical coil and its adjacent angled coil are
manifolded together to serve one refrigerant circuit.
•
The MicroTech II™ control is proactive in response to “off-design conditions”. In the case of
single or compounded influences restricting airflow to the unit, the microprocessor will act to
keep the compressor(s) running (possibly at reduced capacity) rather than allowing a shut-off on
high discharge pressure.
•
The MicroTech II™ control can be programmed to sequence the compressors in the most
advantageous way. For example, in the diagram shown below, it might be desirable to program
circuit #1 to be the lag circuit (last circuit to reach full load) during periods of high ambient
temperatures.
Building
Figure 4, Coil and Fan Arrangement
Circuit #1
Circuit #2
NOTE: Models ACZ 030 to 045 and AGZ 026 to 035 do not have an interior slanted coil.
The following sections discuss the most common situations of condenser air restriction and give
capacity and power adjustment factors for each. Note that in unusually severe conditions, the
MicroTech II™ controller would adjust the unit operation to remain online until a less severe
condition is reached.
6
ACZ / AGZ-BM
IMM ACZ/AGZ-4
Case 1, Building or Wall on One Side of One Unit
The existence of a screening wall, or the wall of a building, in close proximity to an air-cooled unit is
common in both rooftop and ground level applications. Hot air recirculation on the coils adjoining the wall
will increase compressor discharge pressure, decreasing capacity and increasing power consumption. Only
the compressor(s) connected to these coils will be affected.
When close to a wall, place chillers on the north or east-side of them. Have prevailing winds blowing
parallel to the unit’s long axis. The worst case is to have wind blowing hot discharge air into the wall.
Figure 5, Unit Adjacent to Wall
H
D
Figure 6, Adjustment Factors
3.0
ACZ
ACZ
090-155 030-080
ACZ
ACZ
090-155 030-080
AGZ
AGZ
075-130 026-070
AGZ
AGZ
075-130 026-070
4.5 ft.
(1.4m)
3.5 ft.
(1.0m)
2.0
4.5 ft.
(1.4m)
3.5 ft.
(1.0m)
6 ft.
(1.8m)
4 ft.
(1.2m)
8 ft.
(2.4m)
6 ft.
(1.8m)
3.0
1.0
6 ft.
(1.8m)
4 ft.
(1.2m)
.5
8 ft.
(2.4m)
6 ft.
(1.8m)
2.0
0
0
IMM ACZ/AGZ-4
4.0
ACZ / AGZ-BM
7
Case 2, Two Units Side By Side
Two or more units sited side by side are common. If spaced closer than 12 feet (3.7 meters), or 8 feet
(2.5meters), depending on size, it is necessary to adjust the performance of each unit. Circuits adjoining
each other are affected. NOTE: This case applies only to two units side by side. See Case 3 for three or
more parallel units. If one of the two units also has a wall adjoining it, see Case 1. Add the two adjustment
factors together and apply to the unit located between the wall and the other unit.
Mounting units end to end will not necessitate adjusting performance. Depending on the actual
arrangement, sufficient space must be left between the units for access to the control panel door opening
and/or evaporator tube removal. See “Clearance” section of this guide for requirements for specific units.
Figure 7, Two Units Side by Side
Figure 8, Adjustment Factor
3.0
6.0
2.0
4.0
1.0
2.0
0
8
0
AGZ 075-130 9
ACZ 090-155 (2.7)
10
(3.0)
11
(3.3)
12
(3.6)
AGZ 075-130 9
ACZ 090-155 (2.7)
10
(3.0)
11
(3.3)
12
(3.6)
AGZ 026-070 6.5
ACZ 030-080 (2.0)
7
(2.1)
7.5
(2.2)
8
(2.4)
AGZ 026-070 6.5
ACZ 030-080 (2.0)
7
(2.1)
7.5
(2.2)
8
(2.4)
ACZ / AGZ-BM
IMM ACZ/AGZ-4
Case 3, Three or More Units Side By Side
When three or more units are side by side, the outside units (1 and 3 in this case) are influenced by the
middle unit only on their inside circuits. Their adjustment factors will be the same as Case 2. All inside units
(only number 2 in this case) are influenced on both sides and must be adjusted by the factors shown below.
Figure 9, Three or More Units
Chiller 1
Chiller 2
Chiller 3
Figure 10, Adjustment Factor
4.0
8.0
3.0
6.0
2.0
4.0
1.0
2.0
0
0
AGZ 075-130
ACZ 090-155
15
(4.6)
16
(4.9)
17
(5.2)
18
(5.5)
AGZ 075-130
ACZ 090-155
15
(4.6)
16
(4.9)
17
(5.2)
18
(5.5)
AGZ 026-070
ACZ 030-080
11
(3.3)
12
(3.7)
13
(4.0)
14
(4.3)
AGZ 026-070
ACZ 030-080
11
(3.3)
12
(3.7)
13
(4.0)
14
(4.3)
IMM ACZ/AGZ-4
ACZ / AGZ-BM
9
Case 4, Open Screening Walls
Decorative screening walls are often used to help conceal a unit either on grade or on a rooftop. These walls
should be designed such that the combination of their open area and distance from the unit do not require
performance adjustment. It is assumed that the wall height is equal to or less than the unit height when
mounted on its base support. This is usually satisfactory for concealment. If the wall height is greater than
the unit height, see Case 5, Pit Installation.
The distance from the ends of the unit to the end walls must be sufficient for service, opening control panel
doors, and pulling evaporator tubes, as applicable.
If each side wall is a different distance from the unit, the distances can be averaged, providing either wall is
not less than 8 feet (2.4 meters) from the unit. For example, do not average 4 feet and 20 feet to equal 12
feet.
Figure 11, Open Screening Walls
Figure 12, Wall Free Area vs. Distance
AGZ 026-070
ACZ 030-080
AGZ 075-130
ACZ 090-155
4
(1.2)
6
(1.8)
3.5
(1.0)
5
(2.0)
3.0
(0.9)
4
(1.2)
2.5
(0.7)
3
(0.9)
0
10
10
20
ACZ / AGZ-BM
30
40
50
IMM ACZ/AGZ-4
Case 5, Pit/Solid Wall Installation
Pit installations can cause operating problems and great care should be exercised if they are to be used on
an installation. Recirculation and restriction can both occur. A solid wall surrounding a unit is
substantially the same as a pit and the data presented here should be used.
Steel grating is sometimes used to cover a pit to prevent accidental falls or trips into the pit. The grating
material and installation design must be strong enough to prevent such accidents, yet provide abundant
open area or serious recirculation problems will occur. Have any pit installation reviewed by McQuay
application engineers prior to installation for air-flow characteristics. The installation design engineer
must approve the work to avoid an unreasonable risk of accident and is responsible for final design
criteria.
Figure 13, Pit Installation
Figure 14, Adjustment Factor
AGZ 026-070
ACZ 030-080
D=4
(1.4)
D=5
(2.0)
AGZ 026-070
ACZ 030-080
D=4
(1.4)
D=5
(2.0)
AGZ 075-130
ACZ 090-155
D=6
(1.8)
D=8
(2.4)
AGZ 075-130
ACZ 090-155
D=6
(1.8)
D=8
(2.4)
AGZ
AGZ
075-130 026-070
ACZ
ACZ
090-155 030-080
D=10
D=7
(3.1)
(2.1)
IMM ACZ/AGZ-4
ACZ / AGZ-BM
AGZ
AGZ
075-130 026-070
ACZ
ACZ
090-155 030-080
D=10
D=7
(3.1)
(2.1)
11
Sound Isolation
The low sound level of the ACZ/AGZ units is suitable for most applications. When additional sound
reduction is necessary, locate the unit away from sound sensitive areas. Avoid locations beneath
windows, or between structures where normal operating sounds can be objectionable. Reduce
structurally transmitted sound by isolating refrigerant lines, electrical conduit and the unit itself. Use
wall sleeves and rubber isolated piping hangers to reduce transmission of water, refrigerant, or pump
noise into occupied spaces. Use flexible electrical conduit to isolate sound transmission through
electrical conduit. Spring isolators are effective in reducing the low amplitude sound generated by
scroll compressors and for unit isolation in sound sensitive areas.
Vibration Isolators
Vibration isolator springs are recommended for all roof-mounted installations, or wherever vibration
transmission is a consideration. Some form of isolator is also recommended for slab installations,
primarily to keep the unit base from resting its entire length directly on the slab.
Table 2 and Table 3 list isolator point loads for all unit sizes. Figure 15 and 16 shows isolator
locations. See Dimensional Data for detailed mounting hole location.
Isolator Installation
The unit should be initially installed on shims or blocks at the listed free height. When all piping,
wiring, flushing, charging, etc., is completed, adjust the springs upward to load them and to provide
clearance to remove the shims or blocks.
Installation of spring isolators requires flexible piping connections and at least three feet of conduit
flex tie-ins. Piping and conduit must be supported independently of the unit.
Bolting: if the chiller base is to be bolted to the isolators, it is recommended that the short threaded studs
usually found on isolators be replaced with eight-inch threaded rod that can extend through the holes on
the top of the base and then be bolted. Washers will be required.
Figure 15, RP-4, Neoprene-in-Shear Isolators
CP-2, Spring Isolators
Figure 16, Isolator Locations,
4/6 FAN UNIT
8 FAN UNIT
3
4
CONTROL
PANEL
5
6
1
2
3
CONTROL
PANEL
1
12
4
2
ACZ / AGZ-BM
IMM ACZ/AGZ-4
Table 2, Isolator Loads At Each Mounting Location (With Aluminum Fins)
ACZ-B
Model
AGZ-BM
Model
ACZ 030
AGZ 026
ACZ 035
AGZ 030
ACZ 040
AGZ 035
ACZ 045
AGZ 040
ACZ 050
AGZ 045
ACZ 055
AGZ 050
ACZ 060
AGZ 055
ACZ 065
ACZ 070
ACZ 080
AGZ 060
AGZ 065
AGZ 070
Shipping
Wt
Operating.
Wt
Loc. 1
Loc. 2
lbs
3550
3600
1227
901
849
623
3600
72
kg
1608
1631
556
408
385
282
1631
32
lbs
3550
3600
1227
901
849
623
3600
72
kg
1608
1631
556
408
385
282
1631
32
lbs
3550
3600
1227
901
849
623
3600
72
kg
1608
1631
556
408
385
282
1631
32
lbs
3550
3610
1261
872
873
604
3610
72
32
Loc. 3
Loc. 4
(1) Add’l for
Copper Fins
Total
kg
1608
1635
571
395
395
274
1635
lbs
3590
3650
1275
881
883
611
3650
72
kg
1626
1653
578
399
400
277
1653
32
lbs
3730
3800
1295
951
896
658
3800
119
kg
1690
1721
587
431
406
298
1721
54
lbs
3780
3850
1303
1016
860
671
3850
119
kg
1712
1744
590
460
390
304
1744
54
lbs
3820
4040
1367
1066
903
704
4040
142
kg
1730
1830
619
483
409
319
1830
65
lbs
3970
4070
1305
1146
862
757
4070
142
kg
1798
1844
591
519
390
343
1844
65
lbs
4080
4180
1278
1192
885
825
4180
217
kg
1848
1894
579
540
401
374
1894
99
NOTE (1): Additional weight for copper coils is per mounting location.
Table 3, Isolator Loads At Each Mounting Location (With Aluminum Fins)
ACZ
Model
AGZ-BM
Model
ACZ090
AGZ 075
ACZ100
AGZ 085
ACZ110
AGZ 090
ACZ120
AGZ 100
ACZ130
AGZ 110
ACZ140
AGZ 120
ACZ155
AGZ 130
Shipping Operating
Wt.
Wt.
Loc 1
Loc 2
Loc 3
Loc 4
Loc 5
Loc 6
(1)
Add’l
TOTAL
for
Copper
Fins
lbs
5510
5630
1649
1166
1649
1166
-
-
5630
kg
2496
2550
747
528
747
528
-
-
2550
217
99
lbs
5670
5790
1734
1227
1657
1172
-
-
5790
217
kg
2569
2623
786
556
751
531
-
-
2623
99
lbs
5830
5950
1770
1205
1770
1205
-
-
5950
217
kg
2641
2695
802
546
802
546
-
-
2695
99
lbs
6820
6970
1323
1188
1053
1265
1135
1006
6970
289
kg
3089
3157
599
538
477
573
514
456
3157
131
lbs
7080
7230
1396
1205
1014
1396
1205
1014
7230
289
kg
lbs
kg
3207
7360
3334
3275
7480
3388
632
1477
669
546
1275
578
459
1073
486
632
1411
639
546
1218
552
459
1026
465
3275
7480
3388
131
289
131
lbs
7640
7760
1555
1293
1032
1555
1293
1032
7760
289
kg
3461
3515
704
586
467
704
586
467
3515
131
NOTE (1): Additional weight for copper coils is per mounting location.
Table 4, Isolator Kit Numbers
ACZ-B Model
030 - 040
045 - 065
070
080
090 - 110
120, 130
140, 155
AGZ-BM Model
026 - 035
040 - 060
065
070
075 - 090
100, 110
120, 130
Spring Kit Part No.
330349601
330349602
330349603
330349604
330349608
330349610
330349611
R-I-S Kit Part No.
330349701
330349701
330349703
330349703
330349706
330349707
330349708
IMM ACZ/AGZ-4
ACZ / AGZ-BM
13
Table 5, Isolator Locations
ACZ-BS, AGZ-BM Less Evaporator Units
ACZ- AGZBS
BM
Model Model
Operating
Weight
lbs
kg
Neoprene-In-Shear Mountings
1
2
3
4
Spring-Flex Mountings
5
6
1
2
3
4 (1)
5
6
-
-
030
026
3600
1631
Black
Gray
Gray
Green
-
-
Orange Purple
Red
Orange
035
030
3600
1631
Black
Gray
Gray
Green
-
-
Orange Purple
Red
Orange
040
035
3600
1631
Black
Gray
Gray
Green
-
-
Orange Purple
Red
Orange
-
-
045
040
3610
1635
Black
Gray
Gray
Green
-
-
Orange Purple
Purple Orange
-
-
050
045
3650
1653
Black
Gray
Gray
Green
-
-
Orange Purple
Purple Orange
-
-
055
050
3800
1721
Black
Gray
Gray
Green
-
-
Orange Purple
Purple Orange
-
-
060
055
3850
1744
Black
Gray
Gray
Green
-
-
Orange Purple
Purple Orange
-
-
065
060
4040
1830
Black
Gray
Gray
Green
-
-
Orange Purple
Purple Orange
-
-
070
065
4070
1844
Black
Black
Gray
Gray
-
-
Orange Purple
Purple
Red
-
-
080
070
4180
1894
Black
Black
Gray
Gray
-
-
Orange Orange Purple
Red
-
-
090
075
5630
2550
Red
Black
Red
Black
-
-
Green Orange Green Orange
-
-
100
085
5790
2623
Red
Black
Red
Black
-
-
Green Orange Green Orange
-
-
110
090
5950
2695
Red
Black
Red
Black
-
-
Green Orange Green Orange
-
-
120
100
6970
3157
Black
Black
Black
Black
Black
Black
Orange Orange Purple Orange Orange Purple
130
110
7230
3275
Black
Black
Black
Black
Black
Black
Orange Orange Purple Orange Orange Purple
140
120
7480
3388
Red
Black
Black
Red
Black
Black
Green Orange Purple
Green Orange Purple
155
130
7760
3515
Red
Black
Black
Red
Black
Black
Green Orange Purple
Green Orange Purple
NOTE (1): Position #4 is a CP-1, single spring isolator for ACZ 030 to 065 and AGZ 026 to 060. All others are CP-2, two
spring.
Ambient Temperature and Water Flow Limitations
ACZ/AGZ units are designed to operate in ambient temperatures as shown in the following table.
Table 6, Unit Maximum Operating Ambient Temperature
Unit Model
Standard Controls
w/ Low Ambient VFD
Control Option
w/ Low Ambient VFD Control
Plus High Ambient Panel Option
AGZ 026B – 130B
ACZ 030B – 155B
115°F
105°F
125°F
The VFD Low Ambient Control Option imposes an additional heat load on the control panel limiting
operation to 105°F ambient temperature. The addition of the High Ambient Panel Option allows
operation to 125°F ambient temperature.
Compressor loading and unloading is adaptively determined by system load, ambient air temperature,
and other inputs to the MicroTech control algorithms. An optional low ambient fan VFD option allows
operation down to 0°F (-18°C). The minimum ambient temperature is based on still conditions where
the wind is not greater than five mph. Greater wind velocities will result in reduced discharge pressure,
increasing the minimum operating ambient temperature. Field-installed hail/wind guards are available
to allow the chiller to operate effectively down to the ambient temperature for which it was designed.
Evaporator flow rates can be found on page 25. Operation below the minimum values can result in
laminar flow causing freeze-up problems, scaling and poor control. Flow rates above the maximum
values will result in unacceptable pressure drops and can cause excessive erosion, potentially leading to
failure.
Water Piping (Model AGZ-BM)
Local authorities can supply the installer with the proper building and safety codes required for safe and
proper installation.
Install piping with minimum bends and changes in elevation to minimize pressure drop. The following
issues must be considered when designing and installing water piping:
14
ACZ / AGZ-BM
IMM ACZ/AGZ-4
1. Vibration eliminators to reduce vibration and noise transmission to the building.
2. Shutoff valves are required to isolate the unit from the piping system during unit servicing.
3. Manual or automatic air vent valves at the high points of the system. Drains must be installed
at the lowest points in the system.
4. Adequate system water pressure must be maintained (expansion tank or regulating valve).
5. Temperature and pressure indicators located at the unit are required to aid in unit servicing.
6. A strainer or other means of removing foreign matter from the water before it enters the pump
must be installed. Place the strainer far enough upstream to prevent cavitation at the pump
inlet (consult pump manufacturer for recommendations). The use of a strainer will prolong
pump life and keep system performance up.
7. A strainer must be installed in the water line before the inlet of the evaporator. This will help
prevent foreign material from entering and decreasing the evaporator performance.
8. If the unit is used as a replacement chiller, flush the system thoroughly before unit
installation. Regular water analysis and chemical water treatment for the evaporator loop is
recommended immediately at equipment start-up.
9. The total water volume in the system should be sufficient to prevent frequent “on-off”
cycling. Turnover rate should not be less than 4 minutes for normal variable cooling loads.
10. When glycol is added to the water system for freeze protection, the refrigerant suction
pressure will be lower, cooling performance less, and water side pressure drop greater. If the
percentage of glycol is high, or if propylene is used instead of ethylene glycol, the added
pressure drop and loss of performance could be substantial. When Glycol or Ice are selected
as Unit Mode, the MicroTech controller will automatically reset the available range for the
Leaving Water Temperature, Freezestat and Evaporator Pressure settings.
Reset the freezestat setting to approximately 4 to 5 degrees F (2.3 to 2.8 degrees C) below the
leaving chilled water setpoint temperature. See the section titled “Glycol Solutions” for
additional information concerning glycol.
11. Perform a preliminary leak check before insulating the piping and filling the system.
12. Piping insulation should include a vapor barrier to prevent condensation and possible damage
to the building structure from water dripping.
Figure 17, AGZ 075BM – AGZ 130BM, Typical Field Evaporator Water Piping
THERMOWELL
T
INLET
T
IMM ACZ/AGZ-4
ACZ / AGZ-BM
15
Figure 18, AGZ 026BM - AGZ 070BM, Typical Field Evaporator Water Piping
T
Air
Vent
Strainer
Inlet
Isolation
Valves
Vibration
Eliminators
P
Outlet
Flow
Switch
T
Thermowell
Drain
Flow Switch (Model AGZ-BM)
Mount a water flow switch in the leaving water line of the remote water chiller to shut down the unit
when water flow is interrupted. A flow switch is an equipment protection control and should never
be used to cycle a unit.
A flow switch is available from McQuay (part number 017503300). It is a “paddle” type switch and
adaptable to any pipe size from 2” (51 mm) to 6” (152 mm) nominal. Certain minimum flow rates
are required to close the switch and are listed in Table 7. Installation should be as shown in Figure
19. Connect the normally open contacts of the flow switch in the unit control center at terminals 44
and 61. There is also a set of normally closed contacts on the switch that can be used for an indicator
light or an alarm to indicate when a “no flow” condition exists. Freeze protect any flow switch that
is installed outdoors. Manufacturer’s instructions included with the switch should be followed.
NOTE: Differential pressure switches are not recommended for outdoor installation.
Table 7, Flow Switch Minimum/Maximum Flow Rates
Nominal Pipe Size
Inches (mm)
2 (50.8)
2 1/2 (63.50
3 (76.20
4 (101.6)
5 (127.0)
6 (152.4)
Minimum Required Flow To
Activate Switch - gpm (l/m)
13.7 (51.8)
17.9 (67.8)
24.2 (91.6)
35.3 (134.0)
48.6 (184.0)
60.3 (228.0)
Maximum Flow Rate
gpm (l/m)
105 (397.4)
149 (564.0)
230 (870.6)
397 (1502.7)
654 (2475.4)
900 (3406.5)
Note: See pressure drop table on page 25 for minimum and maximum flow through the evaporator.
Figure 19, Flow Switch Installation
Flow direction marked on switch
1" (25mm) NPT flow switch connection
Tee
Water Connections
Bring water piping to the evaporator through the side between the vertical supports. Provide taps for
the connection of pressure gauges and thermometers in the inlet and outlet lines. Check the inlet and
outlet labels on the unit against the certified drawings supplied on the job and be sure the water
piping is hooked up correctly. Contact the McQuay sales office if any discrepancies exist.
16
ACZ / AGZ-BM
IMM ACZ/AGZ-4
Variable Speed Pumping
Variable water flow involves lowering the water flow through the evaporator as the load decreases.
McQuay chillers are designed for this duty provided that the rate of change in water flow is slow and
the minimum and maximum flow rates for the vessel are not exceeded.
The recommended maximum change in water flow is 10 percent of the change per minute.
The water flow through the vessel must remain between the minimum and maximum values listed on
page 25. If flow drops below the minimum allowable, large reductions in heat transfer can occur. If
the flow exceeds the maximum rate, excessive pressure drop and tube erosion can occur.
System Water Volume Considerations
All chillers need adequate time to recognize a load change, respond to the change and stabilize
without short cycling the compressor. The water volume in the system and the size of the piping
loop is a critical consideration. Good engineering practice is to have a minimum water volume of
four times the flow rate (GPM) for comfort cooling applications. For process applications where the
load can change quickly, contact the local McQuay sales office for recommendations. A water
storage tank (provided by others) can be required to increase the system water volume in some
systems.
Since there are many other factors that can influence performance, systems can successfully operate
below these suggestions. However, as the water volume decreases below these suggestions, the
possibility of problems increases. We believe that these guidelines should be an industry standard
and not just recommendations from McQuay.
Glycol Solutions
The use of a glycol/water mixture in the evaporator to prevent freezing will reduce system capacity
and efficiency and increase pressure drop. The system capacity, required glycol solution flow rate,
and pressure drop with glycol can be calculated using the following formulas and tables.
1. Capacity – Multiply the capacity based on water by the Capacity correction factor from Table 8
through Table 11.
2. Flow – Multiply the water evaporator flow by the Flow correction factor from Table 8 through
Table 11 to determine the increased evaporator flow due to glycol.
If the flow is unknown, it can be calculated from the following equation:
Glycol Flow (gpm) =
24 × Tons Capacity ( glycol )
Delta − T
× Flow Correction Factor
3. Pressure drop -- Multiply the water pressure drop from page 25 by Pressure Drop correction
factor from Table 8 through Table 11. High concentrations of propylene glycol at low
temperatures can cause unacceptably high-pressure drops.
4. Power -- Multiply the water system power by Power correction factor from Table 8 through
Table 11.
Test coolant with a clean, accurate glycol solution hydrometer (similar to that found in service
stations) to determine the freezing point. Obtain percent glycol from the freezing point table below.
It is recommended that a minimum of 25% solution by weight be used for protection against
corrosion or that additional compatible inhibitors be added.
IMM ACZ/AGZ-4
ACZ / AGZ-BM
17
CAUTION
Do not use an automotive grade antifreeze. Industrial grade glycols must be used.
Automotive antifreeze contains inhibitors which will cause plating on the copper tubes
within the chiller evaporator. The type and handling of glycol used must be consistent with
local codes.
Table 8, Ethylene Glycol Factors for Models AGZ 026BM to 070BM
% E.G.
10
20
30
40
50
Freeze Point
o
F
26
18
7
-7
-28
o
C
-3.3
-7.8
-13.9
-21.7
-33.3
Capacity
Power
Flow
PD
0.998
0.993
0.987
0.980
0.973
0.998
0.997
0.995
0.992
0.991
1.036
1.060
1.092
1.132
1.182
1.097
1.226
1.369
1.557
1.791
Table 9, Propylene Glycol Factors for Models AGZ 026BM to 070BM
% P.G.
10
20
30
40
50
Freeze Point
o
F
26
19
9
-5
-27
o
C
-3.3
-7.2
-12.8
-20.6
-32.8
Capacity
Power
Flow
PD
0.995
0.987
0.978
0.964
0.952
0.997
0.995
0.992
0.987
0.983
1.016
1.032
1.057
1.092
1.140
1.100
1.211
1.380
1.703
2.251
Table 10, Ethylene Glycol Factors for Models AGZ 075BM to 130BM
% E.G.
10
20
30
40
50
Freeze Point
o
F
26
18
7
-7
-28
o
C
-3.3
-7.8
-13.9
-21.7
-33.3
Capacity
Power
Flow
PD
0.994
0.982
0.970
0.955
0.939
0.998
0.995
0.992
0.987
0.983
1.038
1.063
1.095
1.134
1.184
1.101
1.224
1.358
1.536
1.755
Table 11, Propylene Glycol Factors for Models AGZ 075BM to 130BM
% P.G.
10
20
30
40
50
Freeze Point
o
F
26
19
9
-5
-27
o
C
-3.3
-7.2
-12.8
-20.6
-32.8
Capacity
Power
Flow
PD
0.988
0.972
0.951
0.926
0.906
0.996
0.992
0.987
0.979
0.974
1.019
1.035
1.059
1.095
1.142
1.097
1.201
1.351
1.598
2.039
Altitude Correction Factors
Performance tables are based at sea level. Elevations other than sea level affect the performance of
the unit. The decreased air density will reduce condenser capacity, consequently reducing the unit's
performance. For performance at elevations other than sea level refer to Table 12 or Table 13.
18
ACZ / AGZ-BM
IMM ACZ/AGZ-4
Evaporator Temperature Drop Factors
Performance tables are based on a 10 degree F (5 degree C) temperature drop through the evaporator.
Adjustment factors for applications with temperature ranges from 6 degree F to 16 degree F (3.3
degree C to 8.9 degree C) are found in Table 12 and Table 13. Ranges outside these temperatures
can affect the control system's capability to maintain acceptable control and must not be used.
The maximum water temperature that can be circulated through the evaporator in a non-operating
mode is 100°F (37.8°C).
Fouling Factor
Performance tables are based on water with a fouling factor of:
2
2
0.0001 ft × hr × ° F / BTU or (0.0176 m × °C / kW ) per ARI 550/590-98.
As fouling is increased, performance decreases. For performance at other than 0.0001 (0.0176)
fouling factor, refer to Table 12 and Table 13. Foreign matter in the chilled water system will
adversely affect the heat transfer capability of the evaporator and could increase the pressure drop
and reduce the water flow. Maintain proper water treatment to provide optimum unit operation.
Table 12, Capacity and Power Derates, Models AGZ 026 to 070
Altitude
Sea
Level
2000 feet
4000 feet
6000 feet
8000 feet
IMM ACZ/AGZ-4
Fouling Factor
Chilled Water
Delta T
0.0001 (0.0176)
0.00025 (0.044)
0.00075 (0.132)
0.00175 (0.308)
°F
°C
Cap.
Power
Cap.
Power
Cap.
Power
Cap.
Power
6
3.3
0.978
0.993
0.975
0.991
0.963
0.987
0.940
0.980
8
4.4
0.989
0.996
0.986
0.994
0.973
0.990
0.950
0.983
10
5.6
1.000
1.000
0.996
0.999
0.984
0.994
0.961
0.987
12
6.7
1.009
1.003
1.005
1.001
0.993
0.997
0.969
0.990
14
7.7
1.018
1.004
1.014
1.003
1.002
0.999
0.978
0.991
16
8.9
1.025
1.007
1.021
1.006
1.009
1.001
0.985
0.994
6
3.3
0.977
1.001
0.973
1.000
0.961
0.996
0.938
0.989
8
4.4
0.987
1.006
0.984
1.004
0.971
1.000
0.948
0.993
10
5.6
0.998
1.009
0.995
1.007
0.982
1.003
0.959
0.996
12
6.7
1.007
1.011
1.004
1.010
0.991
1.006
0.967
0.998
14
7.7
1.014
1.014
1.011
1.013
0.998
1.009
0.974
1.001
16
8.9
1.022
1.016
1.018
1.014
1.005
1.010
0.981
1.003
6
3.3
0.973
1.011
0.970
1.010
0.957
1.006
0.935
0.998
8
4.4
0.984
1.014
0.980
1.013
0.968
1.009
0.945
1.001
10
5.6
0.995
1.019
0.991
1.017
0.979
1.013
0.955
1.005
12
6.7
1.004
1.021
1.000
1.020
0.987
1.016
0.964
1.008
14
7.7
1.011
1.024
1.007
1.023
0.994
1.018
0.971
1.011
16
8.9
1.018
1.027
1.014
1.026
1.002
1.021
0.978
1.014
6
3.3
0.969
1.021
0.966
1.020
0.954
1.016
0.931
1.008
8
4.4
0.980
1.026
0.977
1.024
0.964
1.020
0.942
1.013
10
5.6
0.989
1.029
0.986
1.027
0.973
1.023
0.950
1.015
12
6.7
0.998
1.033
0.995
1.031
0.982
1.027
0.959
1.020
14
7.7
1.007
1.036
1.004
1.034
0.991
1.030
0.967
1.022
16
8.9
1.014
1.037
1.011
1.036
0.998
1.031
0.974
1.024
6
3.3
0.964
1.034
0.961
1.033
0.949
1.028
0.926
1.021
8
4.4
0.975
1.037
0.971
1.036
0.959
1.031
0.936
1.024
10
5.6
0.986
1.041
0.982
1.040
0.970
1.036
0.947
1.028
12
6.7
0.995
1.044
0.991
1.043
0.979
1.038
0.955
1.031
14
7.7
1.002
1.047
0.998
1.046
0.986
1.041
0.962
1.034
16
8.9
1.009
1.050
1.005
1.049
0.993
1.044
0.969
1.037
ACZ / AGZ-BM
19
Table 13, Capacity and Power Derates, Models AGZ 075 to 130
Altitude
Sea
Level
2000 feet
4000 feet
6000 feet
8000 feet
20
Fouling Factor
Chilled Water
Delta T
0.0001 (0.0176)
0.00025 (0.044)
0.00075 (0.132)
0.00175 (0.308)
°F
°C
Cap.
Power
Cap.
Power
Cap.
Power
Cap.
Power
6
3.3
0.990
0.997
0.976
0.994
0.937
0.983
0.868
0.964
8
4.4
0.994
0.998
0.981
0.995
0.942
0.984
0.872
0.965
10
5.6
1.000
1.000
0.987
0.996
0.947
0.986
0.877
0.967
12
6.7
1.005
1.001
0.991
0.997
0.951
0.986
0.881
0.968
14
7.7
1.009
1.002
0.995
0.998
0.955
0.987
0.884
0.968
16
8.9
1.013
1.004
1.000
1.000
0.960
0.989
0.889
0.970
6
3.3
0.987
1.005
0.974
1.002
0.934
0.991
0.865
0.972
8
4.4
0.992
1.006
0.979
1.003
0.940
0.992
0.870
0.973
10
5.6
0.997
1.008
0.984
1.004
0.944
0.994
0.875
0.975
12
6.7
1.002
1.009
0.989
1.005
0.949
0.994
0.879
0.975
14
7.7
1.007
1.011
0.993
1.007
0.953
0.996
0.883
0.977
16
8.9
1.011
1.012
0.998
1.008
0.958
0.997
0.887
0.978
6
3.3
0.985
1.014
0.972
1.010
0.933
0.999
0.864
0.980
8
4.4
0.991
1.015
0.977
1.012
0.938
1.001
0.869
0.981
10
5.6
0.995
1.016
0.982
1.013
0.943
1.002
0.873
0.982
12
6.7
1.000
1.018
0.987
1.014
0.947
1.003
0.877
0.984
14
6.8
1.005
1.019
0.991
1.015
0.951
1.004
0.881
0.985
16
8.9
1.009
1.021
0.995
1.017
0.955
1.006
0.884
0.987
6
3.3
0.982
1.023
0.969
1.020
0.930
1.009
0.861
0.989
8
4.4
0.988
1.025
0.975
1.022
0.935
1.010
0.866
0.991
10
5.6
0.992
1.026
0.979
1.022
0.940
1.011
0.870
0.992
12
6.7
0.997
1.028
0.984
1.024
0.944
1.013
0.875
0.994
14
7.7
1.002
1.029
0.989
1.025
0.949
1.014
0.879
0.995
16
8.9
1.006
1.031
0.992
1.027
0.952
1.016
0.882
0.996
6
3.3
0.979
1.034
0.966
1.031
0.927
1.019
0.859
1.000
8
4.4
0.984
1.036
0.971
1.032
0.932
1.021
0.863
1.002
10
5.6
0.990
1.037
0.976
1.033
0.937
1.022
0.868
1.002
12
6.7
0.993
1.039
0.980
1.035
0.941
1.024
0.871
1.004
14
7.7
0.998
1.041
0.985
1.037
0.945
1.026
0.875
1.006
16
8.9
1.003
1.041
0.990
1.038
0.950
1.026
0.879
1.007
ACZ / AGZ-BM
IMM ACZ/AGZ-4
ACZ Staging and Circuiting
All ACZ units have two circuits, each with either two compressors, or three compressors on models
ACZ 120 through 155. These circuits must be kept separated throughout the entire refrigerant piping
system. Each unit refrigerant circuit must be piped to a separate coil or to a separate air handler
(with a single coil).
Temperature control for each evaporator coil is provided by the installer through field-supplied and
wired temperature controllers. The field-supplied staging signals are field-wired to the Microtech II
controller that correspondingly activates and deactivates the scroll compressors. The MicroTech II
controller has a menu screen (See operating manual OM AGZ) that allows selection between “Unit’
and “Circuit”.
Select “Unit” for a single air handler with row control where it does not matter which circuit starts
first. When the controller gets a signal to start Stage 1 of cooling, it will start the compressor, on
either circuit, with the fewest number of starts, so either circuit can start first. Energizing stage 2
will start the compressor with the fewest starts on the other circuit. Further staging requests will
continue to start alternate compressors between the two circuits.
For applications where the staging must be associated with a particular circuit (face-split coils or
separate air handlers), select “Circuit”. In this mode, stages 1, 2, and 3 are connected to refrigerant
circuit #1 and stages 4, 5,and 6 to refrigerant circuit #2. As the thermostat for coil #1 stages up, the
microprocessor will start the compressors on circuit # 1 (compressors 1, 3 and 5). Compressors 5
and 6 are found only on the six compressor units.
The field supplied temperature controller is required to close normally open 24-volt contacts on a
demand for cooling. These closure signals are field wired to the terminal strip (TB3) in the
condensing unit. Refer to the field wiring diagram (page 51) for details. The following control
staging is required:
Condensing Unit Model
ACZ-030B through 110B
ACZ-120B through 155B
Number of
Capacity Steps
4
6
Number of Required
Contact Closure Signals
4
6
In summary:
•
Evaporator coil #1 must be piped to the condensing unit circuit #1. See dimension drawings
beginning on page 52. Evaporator coil #2 must be piped to the condensing unit circuit #2. See
dimension drawings beginning on page 52 for circuit locations.
•
Evaporator staging thermostat for coil #1 must be wired to the unit terminal board TB3, stages 1,
and 2 (and 3 on models 120 through 155). Evaporator staging thermostat for coil #222 must be
wired to the unit terminal board TB3, stages 4, and 5 (and 6 on models 120 through 155).
IMM ACZ/AGZ-4
ACZ / AGZ-BM
21
Remote Evaporator Refrigerant Piping
Figure 20, AGZ-BM, Remote Evaporator Piping Schematic
Refrigerant Specialties:
AGZ-BM Remote Evaporator Chillers: Refrigerant specialties including the expansion valves,
solenoid valves, filter-drier and sight glasses for use with the AGZ-BM remote evaporator models are
supplied by McQuay but require field installation. The remaining components including fittings and
Schrader valves are provided and piped by the installer.
The hot gas bypass valve with solenoid valve option can be provided as a field-installed or factory
installed option.
ACZ-B Condensing Units: No Refrigerant specialties are furnished on the ACZ condensing units. A
variety of evaporator types, other than a water chiller as shown in the above diagram, may be used.
Very often these may be air handlers with multiple-circuited coils. If multiple evaporator circuits and
expansion valves are used, they must be piped so that only two circuits end up being piped back to
the condensing unit, matching the unit’s two refrigerant circuits. Each circuit must have a solenoid
valve with a filter-drier installed ahead of it installed close to the evaporator.
The hot gas bypass valve with solenoid valve option can be provided as a field-installed or factory
installed option.
Unit-Mounted Valves: Both the ACZ-B and the AGZ-BM outdoor sections have a liquid line shutoff
valve and a suction shutoff valve factory mounted as standard.
22
ACZ / AGZ-BM
IMM ACZ/AGZ-4
Refrigerant Piping
All field piping, wiring, and procedures must be performed in accordance with ASHRAE, EPA, and
industry standards. Proper refrigerant piping can make the difference between a reliable system and
an inefficient, problematic system.
The primary concerns related to piping are refrigerant pressure drop, a solid liquid feed to the
expansion valves, continuous oil return and properly sized refrigerant specialties.
Insulate the suction line to reduce excessive superheat build-up. Insulate the liquid line, where
located in areas above ambient temperature, to prevent loss of subcooling and consequent liquid
flashing.
A holding charge of R-22 is provided for the evaporator (AGZ-BM) and the outdoor section. The
installer must properly evacuate the piping system and provide the operating charge of R22. Refer to
the piping schematic drawing on page 22 for additional details.
The recommended source for refrigerant piping techniques and sizing is the ASHRAE 2002
Refrigeration Handbook, chapter 2.
Although conflicting piping recommendations can be found in different sources, McQuay offers the
following recommendations for these controversial issues.
The use of double risers for vertical gas risers is generally not required and should be used only as a
last resort to maintain the minimum refrigerant flow to carry oil up the vertical risers. Slightly
downsizing the vertical riser is a preferable option to providing double risers.
Slope the refrigerant lines 1” per 10 feet of horizontal run in the direction of refrigerant flow to assist
oil return.
Resist using hot gas bypass for applications when operation in ambient temperature below 40
degrees is expected. This recommendation helps to maintain adequate condensing pressures and
liquid refrigerant at the expansion valve when condenser capacities are at their maximum.
Pressure drops in the refrigerant lines should be maintained at or below the ASHRAE
recommendations and line lengths should be made as short as possible. Exceeding these
recommendations will decrease performance and could impact reliability.
Small traps should be provided at the base of each major vertical gas riser to assist in the collection
of oil. If vertical risers exceed more than 25 feet, install a small trap at the midpoint and at a
maximum of 20 foot intervals.
Use caution in sizing the liquid line in applications where the evaporator is above the outdoor
section. The weight of the liquid refrigerant in the vertical column will decrease the pressure at the
top of the riser (approximately 0.5 psi per foot of vertical rise) allowing some of the refrigerant to
flash to a gas. Adequate refrigerant subcooling is needed at the outdoor section to prevent large
volumes of refrigerant gas at the expansion valve.
The piping systems should always extend above the highest component in the refrigeration system
before dropping down to make the final refrigerant connections to components. This practice will
hinder the draining of condensed refrigerant to the lower component when normal shutdown
procedures do not occur (such as a power failure).
NOTE: Do not run refrigerant piping underground.
Pumpdown
The pumpdown capacity of ACZ/AGZ units is given in the Physical Data Tables. Care should be
exercised to include all equipment and lines when calculating the system charge relative to the unit’s
pumpdown capacity. The AGZ-BM remote evaporators have an insignificant operating charge.
IMM ACZ/AGZ-4
ACZ / AGZ-BM
23
Chilled Water Flow Switch
A water flow switch must be mounted in the leaving chilled water line to prove that there is adequate
water flow to the evaporator before the unit can start. It also serves to shut down the unit in the
event that water flow is interrupted in order to guard against evaporator freeze-up.
A flow switch is available from McQuay under ordering number 017503300. It is a paddle-type
switch and adaptable to any pipe size from 1" (25mm) to 8" (203mm) nominal.
Table 14, Flow Switch Settings
Pipe Size
(NOTE !)
Min.
Adjst.
Max.
Adjst.
Flow
No
Flow
Flow
No
Flow
inch
mm
gpm
Lpm
gpm
Lpm
gpm
Lpm
gpm
Lpm
1 1/4
32 (2)
5.8
1.3
3.7
0.8
13.3
3.0
12.5
2.8
1 1/2
38 (2)
7.5
1.7
5.0
1.1
19.2
4.4
18.0
4.1
2
51
13.7
3.1
9.5
2.2
29.0
6.6
27.0
6.1
2 1/2
63 (3)
18.0
4.1
12.5
2.8
34.5
7.8
32.0
7.3
3
76
27.5
6.2
19.0
4.3
53.0
12.0
50.0
11.4
4
102 (4)
65.0
14.8
50.0
11.4
128.0
29.1
122.0
27.7
5
127 (4)
125.0
28.4
101.0
22.9
245.0
55.6
235.0
53.4
6
153 (4)
190.0
43.2
158.0
35.9
375.0
85.2
360.0
81.8
8
204 (5)
205.0
46.6
170.0
38.6
415.0
94.3
400.0
90.8
NOTES:
1. A segmented 3-inch paddle (1, 2, and 3 inches) is furnished mounted, plus a 6-inch paddle loose.
2. Flow rates for a 2-inch paddle trimmed to fit the pipe.
3. Flow rates for a 3-inch paddle trimmed to fit the pipe.
4. Flow rates for a 3-inch paddle.
5. Flow rates for a 6-inch paddle.
24
ACZ / AGZ-BM
IMM ACZ/AGZ-4
Evaporator Flow and Pressure Drop
Figure 21, AGZ 026BM – 130BM, Remote Evaporator Pressure Drop
075-085-090
120-130
026-030
035
040
050
045
AGZ Unit
Model
026B
030B
035B
040B
045B
050B
055B
060B
065B
070B
075B
085B
090B
100B
110B
120B
130B
060
100-110
065-070
055
Minimum
Inch-Pound
S.I.
gpm
DP ft.
lps
DP kpa
41
1.6
2.6
4.7
45
1.9
2.9
5.7
50
1.9
3.1
5.6
58
1.9
3.6
5.7
64
1.8
4.0
5.4
71
1.8
4.4
5.4
78
1.8
4.9
5.3
86
1.7
5.4
5.2
92
1.6
5.8
4.9
98
1.9
6.2
5.6
111
5.6
7.0
16.5
119
6.3
7.5
18.9
128
7.2
8.1
21.4
146
2.6
9.2
7.7
161
3.1
10.2
9.2
180
3.5
11.3
10.4
194
4.1
12.2
12.1
Nominal
Inch-Pound
S.I.
gpm
DP ft.
lps
DP kpa
65
3.9
4.1
11.6
72
4.7
4.6
14.1
80
4.6
5.0
13.8
92
4.7
5.8
14.0
102
4.5
6.4
13.4
113
4.5
7.1
13.3
125
4.4
7.9
13.0
137
4.3
8.6
12.8
147
4.1
9.3
12.1
157
4.6
9.9
13.7
177
12.5
11.2
37.4
191
14.3
12.1
42.7
205
16.2
12.9
48.4
234
6.1
14.8
18.2
258
7.3
16.3
21.7
288
8.9
18.1
26.5
311
10.4
19.6
30.9
Maximum
Inch-Pound
S.I.
gpm
DP ft.
lps
DP kpa
109
10.4
6.9
30.9
121
12.7
7.6
37.8
133
12.4
8.4
36.9
154
12.6
9.7
37.5
170
12.1
10.7
35.9
188
12.0
11.9
35.7
209
11.7
13.2
34.8
228
11.5
14.4
34.2
246
10.9
15.5
32.5
262
12.3
16.5
36.8
295
30.4
18.6
90.7
318
34.8
20.1
103.6
342
39.4
21.6
117.3
390
15.5
24.6
46.2
430
18.5
27.1
55.1
479
24.6
30.2
73.4
518
28.7
32.7
85.6
NOTE: Minimum and maximum flows are established to ensure the Delta-T for each unit size falls within the 6 - 16°F range for
proper unit control. The unit must operate within these values.
IMM ACZ/AGZ-4
ACZ / AGZ-BM
25
Wind Baffles and Hail Guards
Wind Baffles/Hail Guards are a field-installed option that is used to stabilize unit operation in high wind
areas and to assist in operation at low ambient temperatures. Figure 22 is a sketch of a typical panel
assembly on an ACZ/AGZ unit. The actual number of panels and parts will vary by model size. The parts
are shown in the table below and referenced by balloon numbers.
Figure 22, Installation Sequence
Rib Attachment (First)
RIB FLANGES ON THE END
MUST POINT TO CENTER
OF COIL TO HAVE A FINISHED
LOOK. INTERIOR RIB FLANGES
CAN POINT IN ANY DIRECTION.
UNIT VERTICAL COIL
ATTACH ALL RIBS TO
COIL VERTICAL CHANNELS.
Front Panel Attachment (Second)
PLACE FRONT "A" AND
FASTEN TO BOTH SIDES
E
UNIT VERTICAL COIL
D
C
B
2
PLACE FRONT "B" BY LAPPING
OVER "A" AND REPEAT
ATTACHMENT PROCEDURE.
A
1
3
Top Panel Attachment (Last)
E
ATTACH TOP "A" AT HORIZONTAL COIL CHANNEL FIRST.
THIS WILL SQUARE THE PANEL.
OVERLAP THE FRONT PANEL FLANGE.
UNIT VERTICAL COIL
D
C
B
A
ATTACH LEFT SIDE SECOND.
OVERLAP PANEL "B" OVER PANEL "A"
AND REPEAT ATTACHMENT PROCEDURE.
Table 15, Packing List
Description
26
Part Number
ACZ / AGZ-BM
Bubble Number
IMM ACZ/AGZ-4
Vertical Support Rib
Top Cover
Front Panel
¼ - 20 x ½” Screw (Place in Poly Bag)
074758501
330409401
330409501
046093807
1
2
3
Figure 23, Components
TOP
REAR (AGAINST UNIT)
VERTICAL SUPPORT RIB
TOP COVER
FRONT PANEL
Top Panel, Install Last
Overlap the Front panel
Front Panel, Install Second
Rib, Install First
IMM ACZ/AGZ-4
ACZ / AGZ-BM
27
Physical Data
Table 16, ACZ 030B - 040B, AGZ 026BM – 035BM
PHYSICAL DATA
ACZ 030B,
AGZ 026BM
BASIC DATA
Ckt.1
Ckt.2
Number Of Refrigerant Circuits
MODEL NUMBER
ACZ 035B
AGZ 030BM
Ckt.1
Ckt.2
2
ACZ 040B
AGZ 035BM
Ckt.1
Ckt.2
2
2
Unit Operating Charge, R-22, Lbs.
22
22
22
27
27
27
Unit Operating Charge, R-22, kg
10
10
10
12
12
12
Cabinet Dimensions, LxWxH, In.
94.4 x 88.0 x 100.4
94.4 x 88.0 x 100.4
94.4 x 88.0 x 100.4
Cabinet Dimensions, LxWxH, (mm)
2398 x 2235 x 2550 2398 x 2235 x 2550 2398 x 2235 x 2550
Unit Operating Weight, Lb (kg)
3600 (1634)
3600 (1634)
3600 (1634)
Unit Shipping Weight, Lb (kg)
3550 (1612)
3550 (1612)
3550 (1612)
284 (129)
284 (129)
284 (129)
Tandem Scrolls
Tandem Scrolls
Tandem Scrolls
Add'l. Weight If Copper Finned Coils, Lb. (kg)
COMPRESSORS
Type
Nominal tonnage of each Compressor
7.5
7.5
7.5
9.0
9.0
2
2
2
2
2
2
Oil Charge Per Compressor, Oz.
140
140
140
140
140
140
Oil Charge Per Compressor, (g)
(496)
(496)
(496)
(496)
(496)
(496)
Number Of Compressors per Circuit
9.0
CAPACITY REDUCTION STEPS - PERCENT OF COMPRESSOR DISPLACEMENT
Staging, 4 Stages, Circuit #1 in Lead
0-25-50-75-100
0-23-50-73-100
0-25-50-75-100
Staging, 4 Stages, Circuit #2 in Lead
0-25-50-75-100
0-27-50-77-100
0-25-50-75-100
CONDENSERS - HIGH EFFICIENCY FIN AND TUBE TYPE WITH INTEGRAL SUBCOOLING
Coil Face Area Sq. Ft.
26.3
26.3
26.3
26.3
26.3
2.4
2.4
2.4
2.4
2.4
2.4
Fins Per Inch x Rows Deep
50x75.6
1270 x
1920
16 x 3
50x75.6
1270 x
1920
16 x 3
50x75.6
1270 x
1920
16 x 3
50x75.6
1270 x
1920
16 x 3
50x75.6
1270 x
1920
16 x 3
50x75.6
1270 x
1920
16 x 3
Pumpdown Capacity, 90% Full Lbs. (kg)
Maximum Relief Valve Pressure Setting, psig
(kPa)
49 (22)
450
(3103)
49 (22)
450
(3103)
49 (22)
450
(3103)
49 (22)
450
(3103)
49 (22)
450
(3103)
49 (22)
450
(3103)
2
Coil Face Area, (M )
Finned Height x Finned Length, In.
Finned Height x Finned Length, (mm)
26.3
CONDENSER FANS - DIRECT DRIVE PROPELLER TYPE
Number Of Fans - Fan Diameter, In. (mm)
Number Of Motors - HP (kW) (2)
Fan And Motor RPM, 60Hz
60 Hz Fan Tip Speed, FPM (M/Sec)
3
60 Hz Total Unit Airflow, CFM (M /sec)
4 – 30 (762)
4 – 30 (762)
4 – 30 (762)
4 – 1.0
4 – 1.0
4 – 1.0
1140
1140
1140
8950 (4224)
8950 (4224)
8950 (4224)
24,316 (11,478)
24,316 (11,478)
24,316 (11,478)
1
2
5.0 (18.9)
363 (2503)
450 (3102)
3 (76)
Field
Field
1
2
5.7 (21.4)
363 (2503)
450 (3102)
3 (76)
Field
Field
REMOTE EVAPORATOR - BRAZED PLATE (AGZ-BM ONLY)
Number of Evaporators
1
Number of Refrigerant Circuits
2
Water Volume, Gallons, (L)
4.3 (16.4)
Maximum Water Pressure, psig (kPa)
363 (2503)
Max. Refrig. Working Pressure, psig (kPa)
450 (3102)
Water Inlet / Outlet Victaulic Conn. In. (mm)
3 (76)
Drain - NPT int., In. (mm)
Field
Vent - NPT int., In. (mm)
Field
NOTES:
1.
Nominal capacity based on 95°F ambient air and 50°F SST.
2.
Except for 380V/60 & 575V/60, HP = 2.0
28
ACZ / AGZ-BM
IMM ACZ/AGZ-4
Table 17, ACZ 045B - 060B, AGZ 040BM – 055BM
PHYSICAL DATA
BASIC DATA
MODEL NUMBER
ACZ 050B
ACZ 055B
AGZ 045BM
AGZ 050BM
ACZ 045B
AGZ 040BM
Ckt.1
Number Of Refrigerant Circuits
Ckt.1
Ckt.2
2
Unit Operating Charge, R-22, lbs.
Unit Operating Charge, R-22, kg
Cabinet Dimensions, LxWxH, in.
Cabinet Dimensions, LxWxH, (mm)
Unit Operating Weight, Lbs. (kg)
Ckt.1
Ckt.2
Ckt.1
2
ACZ 060B
AGZ 055BM
Ckt.2
2
Ckt.2
2
31
31
37
37
37
37
44
44
14
14
17
17
17
17
20
20
94.4 x 88.0 x 100.4 94.4 x 88.0 x 100.4 94.4 x 88.0 x 100.4 94.4 x 88.0 x 100.4
2398 x 2235 x
2398 x 2235 x
2398 x 2235 x
2398 x 2235 x
2250
2250
2250
2250
3610 (1639)
3650 (1657)
3800 (1725)
3850 (1748)
Unit Shipping Weight, Lbs. (kg)
3550 (1612)
3590 (1630)
3730 (1693)
3780 (1716)
288 (130)
288 (130)
476 (130)
476 (130)
Type
Tandem Scrolls
Tandem Scrolls
Tandem Scrolls
Tandem Scrolls
Nominal tonnage of each Compressor
10.0
10.0
10.0
13.0
13.0
13.0
13.0
15.0
2
2
2
2
2
2
2
2
Add'l. Weight If Copper Finned Coils, lbs. (kg)
COMPRESSORS
Number Of Compressors per Circuit
Oil Charge Per Compressor, oz.
140
140
140
140
140
140
140
140
Oil Charge Per Compressor, (g)
(496)
(496)
(496)
(496)
(496)
(496)
(496)
(496)
CAPACITY REDUCTION STEPS - PERCENT OF COMPRESSOR DISPLACEMENT
Staging, 4 Stages, Circuit #1 in Lead
0-25-50-75-100
0-22-50-46-100
0-25-50-75-100
0-25-50-75-100
Staging, 4 Stages, Circuit #2 in Lead
0-25-50-75-100
0-28-50-85-100
0-25-50-75-100
0-25-50-75-100
CONDENSERS - HIGH EFFICIENCY FIN AND TUBE TYPE WITH INTEGRAL SUBCOOLING
Coil Face Area, sq. ft. (Note 1)
26.3
26.3
44.1
44.1
44.1
44.1
44.1
44.1
Coil Face Area (sq. M)
2.4
2.4
4.1
4.1
4.1
4.1
4.1
4.1
42x75.6
1067 x
1920
16 x 2
42x75.6
1067 x
1920
16 x 3
42x75.6
1067 x
1920
16 x 3
60(27)
450
(3103)
82 (37)
450
(3103)
82 (37)
450
(3103)
Finned Height x Finned Length, in.
Fins Per Inch x Rows Deep
50x75.6
1270 x
1920
16 x 3
50x75.6 42x75.6 42x75.6 42x75.6
1270 x
1067 x
1067 x
1067 x
1920
1920
1920
1920
16 x 3
16 x 2
16 x 2
16 x 2
Pumpdown Capacity, 90% Full Lbs. (kg)
Maximum Relief Valve Pressure Setting, psig
(kPa)
49 (22)
450
(3103)
49 (22)
450
(3103)
Finned Height x Finned Length, (mm)
60(27)
450
(3103)
60(27)
450
(3103)
60(27)
450
(3103)
CONDENSER FANS - DIRECT DRIVE PROPELLER TYPE
Number Of Fans - Fan Diameter, in. (mm)
4 – 30 (762)
4 – 30 (762)
4 – 30 (762)
4 – 30 (762)
4 – 1.5
4 – 1.5
4 – 1.5
4 – 1.5
1140
1140
1140
1140
8950 (4224)
8950 (4224)
8950 (4224)
8950 (4224)
39,600 (18,692)
39,600 (18,692)
37,228 (17,572)
37,228 (17,572)
1
2
7.2 (27.3)
363 (2503)
1
2
8.1 (30.7)
363 (2503)
1
2
9.2 (34.9)
363 (2503)
450 (3102)
450 (3102)
450 (3102)
3 (76)
Field
Field
3 (76)
Field
Field
3 (76)
Field
Field
Number Of Motors - HP (kW) (Note 2))
Fan And Motor RPM, 60Hz
60 Hz Fan Tip Speed, FPM (m/sec)
3
60 Hz Total Unit Airflow, CFM (m /sec)
REMOTE EVAPORATOR - BRAZED PLATE (AGZ-BM ONLY)
Number of Evaporators
1
Number of Refrigerant Circuits
2
Water Volume, Gallons, (L)
6.3 (23.9)
Maximum Water Pressure, psig (kPa)
363 (2503)
Maximum Refrigerant Working Pressure, psig
450 (3102)
(kPa)
Water Inlet / Outlet Victaulic Conn., in. (mm)
3 (76)
Drain - NPT int., in. (mm)
Field
Vent - NPT int., in. (mm)
Field
NOTES:
1.
The AGZ 040 condenser is the same as the AGZ 045.
2.
Except for 380V/60 & 575V/60, HP = 2.0
IMM ACZ/AGZ-4
ACZ / AGZ-BM
29
Table 18, ACZ 065B - 080B, AGZ 060BM – 070BM
PHYSICAL DATA
ACZ 065B
AGZ 060BM
BASIC DATA
Ckt.1
Number Of Refrigerant Circuits
Ckt.2
MODEL NUMBER
ACZ 070B
AGZ 065BM
Ckt.1
2
Unit Operating Charge, R-22, lbs.
Unit Operating Charge, R-22, kg
Cabinet Dimensions, LxWxH, in.
Ckt.2
ACZ 080B
AGZ 070BM
Ckt.1
Ckt.2
2
2
44
44
50
57
57
57
20
20
23
26
26
26
94.4 x 88.0 x 100.4 94.4 x 88.0 x 100.4 94.4 x 88.0 x 100.4
2398 x 2235 x
2398 x 2235 x
2398 x 2235 x
2550
2550
2550
4040 (1834)
4070 (1848)
4180 (1898)
Cabinet Dimensions, LxWxH, (mm)
Unit Operating Weight, Lbs. (kg)
Unit Shipping Weight, Lbs. (kg)
3820 (1734)
3970 (1802)
4080 (1852)
476 (216)
568 (258)
568 (258)
Type
Tandem Scrolls
Tandem Scrolls
Nominal tonnage of each Compressor
15.0
15.0
15.0
15 / 20
15 / 20
15 / 20
2
2
2
2
2
2
Add'l Weight If Copper Finned Coils, lbs. (kg)
COMPRESSORS
Number Of Compressors per Circuit
Tandem Scrolls
Oil Charge Per Compressor, oz.
140
140
140
140 /148 140 /148 140 /148
Oil Charge Per Compressor, (g)
(496)
(496)
(496)
496/ 525 496/ 525 496/ 525
CAPACITY REDUCTION STEPS - PERCENT OF COMPRESSOR DISPLACEMENT
Staging, 4 Stages, Circuit #1 in Lead
0-25-50-75-100
0-23-46-77-100
0-25-50-75-100
Staging, 4 Stages, Circuit #2 in Lead
0-25-50-75-100
0-31-46-69-100
0-25-50-75-100
CONDENSERS - HIGH EFFICIENCY FIN AND TUBE TYPE WITH INTEGRAL SUBCOOLING
Coil Face Area, sq. ft.
2
Coil Face Area, (m )
Finned Height x Finned Length, in.
44.1
44.1
52.6
52.6
52.6
52.6
4.1
4.1
4.9
4.9
4.9
4.9
42x75.6
1067 x
1920
16 x 3
Finned Height x Finned Length, (mm)
Fins Per Inch x Rows Deep
Pumpdown Capacity, 90% Full Lbs. (kg)
Maximum Relief Valve Pressure Setting, psig
(kPa)
82 (37
450
(3103)
42x75.6 100x75.6 100x75.6 100x75.6 100x75.6
1067 x
2540 x
2540 x
2540 x
2540 x
1920
1920
1920
1920
1920
16 x 3
16 x 3
16 x 3
16 x 3
16 x 3
82 (37
450
(3103)
98 (44
450
(3103)
98 (44
450
(3103)
98 (44
450
(3103)
98 (44
450
(3103)
CONDENSER FANS - DIRECT DRIVE PROPELLER TYPE
Number Of Fans - Fan Diameter, in. (mm)
Number Of Motors - HP (kW) (1)
Fan And Motor RPM, 60Hz
60 Hz Fan Tip Speed, FPM (m/sec)
3
60 Hz Total Unit Airflow, CFM (m /sec)
4 – 30 (762)
4 – 30 (762)
4 – 30 (762)
4 – 1.5
4 – 2.0
4 – 2.0
1140
1140
1140
8950 (4224)
8950 (4224)
8950 (4224)
37,228 (17,572
43,452 (20,510)
43,452 (20,510)
1
2
11.2 (42.5)
363 (2503)
450 (3102)
3 (76)
Field
Field
1
2
11.2 (42.5)
363 (2503)
450 (3102)
3 (76)
Field
Field
REMOTE EVAPORATOR - BRAZED PLATE (AGZ-BM ONLY)
Number of Evaporators
1
Number of Refrigerant Circuits
2
Water Volume, Gallons, (L)
9.2 (34.9)
Maximum Water Pressure, psig (kPa)
363 (2503)
Maximum Refrigerant Working Press., psig (kPa)
450 (3102)
Water Inlet / Outlet Victaulic Conn., in. (mm)
3 (76)
Drain - NPT int, in. (mm)
Field
Vent - NPT int, in. (mm)
Field
NOTE: Except for 380V/60 & 575V/60, HP = 2.0
30
ACZ / AGZ-BM
IMM ACZ/AGZ-4
Table 19, ACZ 090B - 110B, AGZ 075BM – 090BM
PHYSICAL DATA
ACZ 090B
AGZ 075BM
Ckt.1
Ckt.2
2
56
56
25
25
134.9 x 88.0 x 100.4
3426 x 2235 x 2550
5630 (2556)
5510 (2502)
870 (395)
MODEL NUMBER
ACZ 100B
AGZ 085BM
Ckt.1
Ckt.2
2
56
66
25
30
134.9 x 88.0 x 100.4
3426 x 2235 x 2550
5790 (2629)
5670 (2574)
870 (395)
ACZ 110B
AGZ 090BM
Ckt.1
Ckt.2
2
66
66
30
30
134.9 x 88.0 x 100.4
3426 x 2235 x 2550
5950 (2701)
5830 (2647)
870 (395)
1
2
14.0 x 5.2
356 x 1585
25 (95)
152 (1047)
300 (2066)
5 (127)
0.5 (12.7)
0.5 (12.7)
1
2
14.0 x 5.2
356 x 1585
25 (95)
152 (1047)
300 (2066)
5 (127)
0.5 (12.7)
0.5 (12.7)
BASIC DATA
Number Of Refrigerant Circuits
Unit Operating Charge, R-22, lbs.
Unit Operating Charge, R-22, (kg)
Cabinet Dimensions, LxWxH, in.
Cabinet Dimensions, LxWxH, (mm)
Unit Operating Weight, Lbs. (kg)
Unit Shipping Weight, Lbs. (kg)
Add'l Weight If Copper Finned Coils, lbs. (kg)
COMPRESSORS
Type
Tandem Scrolls
Tandem Scrolls
Tandem Scrolls
Nominal tonnage of each Compressor
20.0
20.0
20.0
25.0
25.0
25.0
Number Of Compressors per Circuit
2
2
2
2
2
2
Oil Charge Per Compressor, oz.
148
148
148
200
200
200
Oil Charge Per Compressor, (g)
(525)
(525)
(525)
(709)
(709)
(709)
CAPACITY REDUCTION STEPS - PERCENT OF COMPRESSOR DISPLACEMENT
Staging, 4 Stages, Circuit #1 in Lead
0-25-50-75-100
0-22-50-72-100
0-25-50-75-100
Staging, 4 Stages, Circuit #2 in Lead
0-25-50-75-100
0-28-50-78-100
0-25-50-75-100
CONDENSERS - HIGH EFFICIENCY FIN AND TUBE TYPE WITH INTEGRAL SUBCOOLING
Coil Face Area, sq. ft.
78.8
78.8
78.8
78.8
78.8
78.8
2
Coil Face Area, (m )
7.3
7.3
7.3
7.3
7.3
7.3
Finned Height x Finned Length, in.
50 x113.4 50 x113.4 50 x113.4 50 x113.4 50 x113.4 50 x113.4
1270 x
1270 x
1270 x
1270 x
1270 x
1270 x
Finned Height x Finned Length, (mm)
2880
2880
2880
2880
2880
2880
Fins Per Inch x Rows Deep
16 x 3
16 x 3
16 x 3
16 x 3
16 x 3
16 x 3
Pumpdown Capacity, 90% Full Lbs. (kg)
147 (67) 147 (67) 147 (67) 147 (67) 147 (67) 147 (67)
450
450
450
450
450
450
Maximum Relief Valve Pressure Setting, psig (kPa)
(3103)
(3103)
(3103)
(3103)
(3103)
(3103)
CONDENSER FANS - DIRECT DRIVE PROPELLER TYPE
Number Of Fans - Fan Diameter, in. (mm)
6 – 30 (762)
6 – 30 (762)
6 – 30 (762)
Number Of Motors - HP (kW)
6 – 2.0
6 – 2.0
6 – 2.0
Fan And Motor RPM, 60Hz
1140
1140
1140
60 Hz Fan Tip Speed, FPM (m/sec)
8950 (4224)
8950 (4224)
8950 (4224)
3
60 Hz Total Unit Airflow, CFM (m /sec)
65,178 (30,765)
65,178 (30,765)
65,178 (30,765)
REMOTE EVAPORATOR - SHELL AND TUBE (AGZ-BM ONLY)
Number of Evaporators
1
Number of Refrigerant Circuits
2
Diameter, in. - Length, ft.
14.0 x 5.2
Diameter, (mm) – Length, (mm)
356 x 1585
Water Volume, Gallons, (L)
25 (95)
Maximum Water Pressure, psig (kPa)
152 (1047)
Maximum Refrigerant Working Pressure, psig (kPa)
300 (2066)
Water Inlet / Outlet Victaulic Connections, in. (mm)
5 (127)
Drain - NPT int, in. (mm)
0.5 (12.7)
Vent - NPT int, in. (mm)
0.5 (12.7)
IMM ACZ/AGZ-4
ACZ / AGZ-BM
31
Table 20, ACZ 120B - 155B, AGZ 100BM – 130BM
PHYSICAL DATA
ACZ 120B
AGZ 100BM
Ckt.1
Ckt.2
2
72
82
33
37
173.1 x 88.0 x 100.4
4397 x 2235 x 2550
6970 (3164
6820 (3096)
1155 (524)
MODEL NUMBER
ACZ 130B
ACZ 140B
AGZ 110BM
AGZ 120BM
Ckt.1
Ckt.2
Ckt.1
Ckt.2
2
2
82
82
82
99
37
37
37
45
173.1 x 88.0 x 100.4 173.1 x 88.0 x 100.4
4397 x 2235 x 2550 4397 x 2235 x 2550
7230 (3282)
7480 (3396)
7080 (3214)
7360 (3341)
1155 (524)
1155 (524)
BASIC DATA
Number Of Refrigerant Circuits
Unit Operating Charge, R-22, lbs.
Unit Operating Charge, R-22, (kg)
Cabinet Dimensions, LxWxH, in.
Cabinet Dimensions, LxWxH, (mm)
Unit Operating Weight, Lbs. (kg)
Unit Shipping Weight, Lbs. (kg)
Add'l. Weight If Copper Finned Coils, lbs. (kg)
COMPRESSORS
Type
Trio Scrolls
Trio Scrolls
Nominal tonnage of each Compressor
15.0
20.0
20.0
20.0
Number Of Compressors per Circuit
3
3
3
3
Oil Charge Per Compressor, oz.
140
148
148
148
Oil Charge Per Compressor, (g)
(496)
(525)
(525)
(525)
CAPACITY REDUCTION STEPS - PERCENT OF COMPRESSOR DISPLACEMENT
Staging, 6 Stages, Circuit #1 in Lead
0-14-33-48-67-81-100 0-17-33-50-67-83-100
Staging, 6 Stages, Circuit #2 in Lead
0-19-33-52-67-86-100 0-17-33-50-67-83-100
CONDENSERS - HIGH EFFICIENCY FIN AND TUBE TYPE WITH INTEGRAL SUBCOOLING
Coil Face Area, sq. ft.
105.3
105.3
105.3
105.3
2
Coil Face Area, (m )
9.8
9.8
9.8
9.8
Finned Height x Finned Length, in.
50 x151.6 50 x151.6 50 x151.6 50 x151.6
1270 x
1270 x
1270 x
1270 x
Finned Height x Finned Length, (mm)
3851
3851
3851
3851
Fins Per Inch x Rows Deep
16 x 3
16 x 3
16 x 3
16 x 3
Pumpdown Capacity, 90% Full Lbs. (kg)
196 (89) 196 (89) 196 (89) 196 (89)
Maximum Relief Valve Pressure Setting, psig
450
450
450
450
(kPa)
(3103)
(3103)
(3103)
(3103)
CONDENSER FANS - DIRECT DRIVE PROPELLER TYPE
Number Of Fans - Fan Diameter, in. (mm)
8 – 30 (762)
8 – 30 (762)
Number Of Motors - HP (kW)
8 – 2.0
8 – 2.0
Fan And Motor RPM, 60Hz
1140
1140
60 Hz Fan Tip Speed, FPM (m/sec)
8950 (4224)
8950 (4224)
3
60 Hz Total Unit Airflow, CFM (m /sec)
86,904 (41,020)
86,904 (41,020)
REMOTE EVAPORATOR - SHELL AND TUBE (AGZ-BM ONLY)
Number of Evaporators
1
Number of Refrigerant Circuits
2
Diameter, in. - Length, ft.
12.8 x 7.9
Diameter, (mm) – Length, (mm)
324 x 2408
Water Volume, Gallons, (L)
34 (127)
Maximum Water Pressure, psig (kPa)
152 (1047)
Maximum Refrigerant Working Press., psig (kPa)
300 (2066)
Water Inlet / Outlet Victaulic Conn., in. (mm)
5 (127)
Drain - NPT int., in. (mm)
0.5 (12.7)
Vent - NPT int., in. (mm)
0.5 (12.7)
32
ACZ / AGZ-BM
1
2
12.8 x 7.9
324 x 2408
34 (127)
152 (1047)
300 (2066)
5 (127)
0.5 (12.7)
0.5 (12.7)
Trio Scrolls
20.0
25.0
3
3
148
200
(525)
(709)
ACZ 155B
AGZ 130BM
Ckt.1
Ckt.2
2
99
99
45
45
173.1 x 88.0 x 100.4
4397 x 2235 x 2550
7760 (3523)
7640 (3469)
1155 (524)
Trio Scrolls
25.0
25.0
3
3
200
200
(709)
(709)
0-15-33-48-67-81-100 0-17-33-50-67-83-100
0-19-33-52-67-86-100 0-17-33-50-67-83-100
105.3
105.3
105.3
105.3
9.8
9.8
9.8
9.8
50 x151.6 50 x151.6 50 x151.6 50 x151.6
1270 x
1270 x
1270 x
1270 x
3851
3851
3851
3851
16 x 3
16 x 3
16 x 3
16 x 3
196 (89) 196 (89) 196 (89) 196 (89)
450
450
450
450
(3103)
(3103)
(3103)
(3103)
8 – 30 (762)
8 – 2.0
1140
8950 (4224)
86,904 (41,020)
8 – 30 (762)
8 – 2.0
1140
8950 (4224)
86,904 (41,020)
1
2
14.0 x 8.0
356 x 2438
40 (150)
152 (1047)
300 (2066)
5 (127)
0.5 (12.7)
0.5 (12.7)
1,
2
14.0 x 8.0
356 x 2438
40 (150)
152 (1047)
300 (2066)
5 (127)
0.5 (12.7)
0.5 (12.7)
IMM ACZ/AGZ-4
Electrical Data Standard Ambient
Table 21, ACZ BC & AGZ BM Electrical Data, Single Point (105°F & below)
ACZ
Unit
Size
AGZ
Unit
Size
030B
026B
035B
030B
040B
035B
045B
040B
050B
045B
055B
050B
060B
055B
065B
060B
070B
065B
080B
070B
Volts
Minimum
Circuit
Ampacity
(MCA)
208
230
380
460
575
208
230
380
460
575
208
230
380
460
575
208
230
380
460
575
208
230
380
460
575
208
230
380
460
575
208
230
380
460
575
208
230
380
460
575
208
230
380
460
575
208
230
380
460
575
133
126
80
68
52
146
143
88
74
58
158
150
96
79
64
167
167
113
81
70
184
184
121
94
78
199
199
127
104
86
221
214
145
108
96
248
228
156
112
105
281
281
162
124
109
301
301
168
130
112
Power Supply
Field Wire
Wire
Quantity
Gauge
75C
3
1/0
3
#1
3
#4
3
#4
3
#6
3
1/0
3
1/0
3
#3
3
#4
3
#6
3
2/0
3
1/0
3
#3
3
#4
3
#6
3
2/0
3
2/0
3
#2
3
#4
3
#4
3
3/0
3
3/0
3
#1
3
#3
3
#4
3
3/0
3
3/0
3
#1
3
#2
3
#3
3
4/0
3
4/0
3
1/0
3
#2
3
#3
3
250
3
4/0
3
2/0
3
#2
3
#2
3
300
3
300
3
2/0
3
#1
3
#2
3
350
3
350
3
2/0
3
#1
3
#2
Recomm’d.
Fuse
Or HACR
Breaker
Size
150
150
90
80
60
175
175
100
80
70
175
175
110
90
70
200
200
125
90
80
225
225
125
110
90
225
225
150
125
100
250
250
175
125
110
300
250
175
125
125
350
350
200
150
125
350
350
200
150
125
Max. Fuse
Or HACR
Breaker
Size
150
150
90
80
60
175
175
100
90
70
175
175
110
90
70
200
200
125
90
80
225
225
125
110
90
225
225
150
125
100
250
250
175
125
110
300
250
175
125
125
350
350
200
150
125
350
350
200
150
125
NOTES:
1. Units operating in ambient temperatures of 95°F (35°C) and above must use the Maximum Fuse or HACR
Breaker size.
2. All Electrical Data notes are on page 49.
3. Conduit hubs are not provided.
IMM ACZ/AGZ-4
ACZ / AGZ-BM
33
Table 22, ACZ BC & AGZ BM Compressor & Fan Motor Amps, Single & Multi-Point
(Up to 105°F)
ACZ
Unit
Size
AGZ
Unit
Size
Rated Load Amps
Compressors
Volts
No. 1
No. 3 No. 2
208
25.7
25.7
230
24.2
24.2
14.9
14.9
030B 026B 380
460
13.4
13.4
575
9.3
9.3
208
25.7
25.7
230
24.2
24.2
14.9
14.9
035B 030B 380
460
13.4
13.4
575
9.3
9.3
208
31.8
31.8
230
29.9
29.9
18.6
18.6
040B 035B 380
460
16.0
16.0
575
12.2
12.2
208
33.8
33.8
230
33.8
33.8
22.8
22.8
045B 040B 380
460
16.5
16.5
575
13.7
13.7
208
33.8
33.8
230
33.8
33.8
22.8
22.8
050B 045B 380
460
16.5
16.5
575
13.7
13.7
208
41.4
41.4
230
41.4
41.4
26.0
26.0
055B 050B 380
460
21.8
21.8
575
17.3
17.3
208
41.0
41.0
230
41.0
41.0
26.0
26.0
060B 055B 380
460
21.8
21.8
575
17.3
17.3
208
52.8
52.8
230
48.1
48.1
32.7
32.7
065B 060B 380
460
23.7
23.7
575
21.8
21.8
208
52.8
52.8
230
52.8
52.8
32.7
32.7
070B 065B 380
460
23.7
23.7
575
21.8
21.8
208
52.8
73.1
230
52.8
73.1
32.7
38.2
080B 070B 380
460
23.7
30.1
575
21.8
25.2
All Electrical Data notes are on page
34
25.7
24.2
14.9
13.4
9.3
31.8
31.8
18.6
16.0
12.2
31.8
29.9
18.6
16.0
12.2
33.8
33.8
22.8
16.5
13.7
41.4
41.4
26.0
21.8
17.3
41.4
41.4
26.0
21.8
17.3
51.3
48.1
33.8
23.7
21.8
52.8
48.1
32.7
23.7
21.8
52.8
52.8
32.7
23.7
21.8
52.8
52.8
32.7
23.7
21.8
49
F.L.Amps
Per Fan
No. 4
Motor
25.7
24.2
14.9
13.4
9.3
31.8
31.8
18.6
16.0
12.2
31.8
29.9
18.6
16.0
12.2
33.8
33.8
22.8
16.5
13.7
41.4
41.4
26.0
21.8
17.3
41.4
41.4
26.0
21.8
17.3
51.3
48.1
33.8
23.7
21.8
52.8
48.1
32.7
23.7
21.8
73.1
73.1
38.2
30.1
25.2
73.1
73.1
38.2
30.1
25.2
No. Of
Fan
Motors
5.8
5.8
4.1
2.8
3.0
5.8
5.8
4.1
2.8
3.0
5.8
5.8
4.1
2.8
3.0
5.8
5.8
4.1
2.8
3.0
5.8
5.8
4.1
2.8
3.0
5.8
5.8
4.1
2.8
3.0
5.8
5.8
4.1
2.8
3.0
5.8
5.8
4.1
2.8
3.0
7.8
7.8
4.1
3.6
3.0
7.8
7.8
4.1
3.6
3.0
ACZ / AGZ-BM
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
Fan
Motors
Each
23.3
26.1
20.0
13.0
14.0
23.3
26.1
20.0
13.0
14.0
23.3
26.1
20.0
13.0
14.0
23.3
26.1
20.0
13.0
14.0
23.3
26.1
20.0
13.0
14.0
23.3
26.1
20.0
13.0
14.0
23.3
26.1
20.0
13.0
14.0
23.3
26.1
20.0
13.0
14.0
31.7
35.6
20.0
17.8
14.0
31.7
35.6
20.0
17.8
14.0
Locked Rotor Amps
Compressors
Across- The- Line
No.1
No. 3
No.2
No.4
189
189
112
99
74
189
189
112
99
74
232
232
144
125
100
278
278
151
127
100
278
278
151
127
100
350
350
195
158
125
350
350
195
158
125
425
425
239
187
148
425
425
239
187
148
425
425
239
187
148
189
189
112
99
74
189
189
112
99
74
232
232
144
125
100
278
278
151
127
100
278
278
151
127
100
350
350
195
158
125
350
350
195
158
125
425
425
239
187
148
425
425
239
187
148
505
505
280
225
180
189
189
112
99
74
232
232
144
125
100
232
232
144
125
100
278
278
151
127
100
350
350
195
158
125
350
350
195
158
125
425
425
239
187
148
425
425
239
187
148
425
425
239
187
148
425
425
239
187
148
189
189
112
99
74
232
232
144
125
100
232
232
144
125
100
278
278
151
127
100
350
350
195
158
125
350
350
195
158
125
425
425
239
187
148
425
425
239
187
148
505
505
280
225
180
505
505
280
225
180
IMM ACZ/AGZ-4
Table 23, ACZ BC & AGZ BM Field Wiring, Single Point
ACZ
Unit
Size
AGZ
Unit
Size
030B
026B
035B
030B
040B
035B
045B
040B
050B
045B
055B
050B
060B
055B
065B
060B
070B
065B
080B
070B
All Electrical Data
IMM ACZ/AGZ-4
Wiring to Standard
Power Block
Volts
Terminal
Amps
208
175
230
175
380
175
460
175
575
175
208
380
230
380
380
175
460
175
575
175
208
380
230
380
380
175
460
175
575
175
208
380
230
380
380
175
460
175
575
175
208
380
230
380
380
175
460
175
575
175
208
380
230
380
380
175
460
175
575
175
208
380
230
380
380
175
460
175
575
175
208
380
230
380
380
380
460
175
575
175
208
380
230
380
380
380
460
175
575
175
208
380
230
380
380
380
460
380
575
175
notes are on page 49.
Connector Wire
Range
(Copper Wire Only)
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
#4 – 500 kcmil
#4 – 500 kcmil
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
#4 – 500 kcmil
#4 – 500 kcmil
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
#4 – 500 kcmil
#4 – 500 kcmil
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
#4 – 500 kcmil
#4 – 500 kcmil
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
#4 – 500 kcmil
#4 – 500 kcmil
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
#4 – 500 kcmil
#4 – 500 kcmil
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
#4 – 500 kcmil
#4 – 500 kcmil
#4 – 500 kcmil
14 GA – 2/0
14 GA – 2/0
#4 – 500 kcmil
#4 – 500 kcmil
#4 – 500 kcmil
14 GA – 2/0
14 GA – 2/0
#4 – 500 kcmil
#4 – 500 kcmil
#4 – 500 kcmil
#4 – 500 kcmil
14 GA – 2/0
ACZ / AGZ-BM
Wiring to Optional
Non-Fused Disconnect Switch
Disconnect
Size
225
225
150
150
150
225
225
150
150
150
225
225
150
150
150
225
225
150
150
150
225
225
150
150
150
250
250
150
150
150
400
400
250
150
150
400
400
250
150
150
400
400
250
250
150
400
400
250
250
150
Connector Wire
Range
(Copper Wire Only)
# 4 - 300 kcmil
# 4 - 300 kcmil
# 4 - 300 kcmil
# 4 - 300 kcmil
# 4 - 300 kcmil
# 4 - 300 kcmil
# 4 - 300 kcmil
# 4 - 300 kcmil
# 4 - 300 kcmil
# 4 - 300 kcmil
# 4 - 300 kcmil
# 4 - 300 kcmil
# 4 - 300 kcmil
# 4 - 300 kcmil
# 4 - 300 kcmil
# 4 - 300 kcmil
# 4 - 300 kcmil
# 4 - 300 kcmil
# 4 - 300 kcmil
# 4 - 300 kcmil
# 4 - 300 kcmil
# 4 - 300 kcmil
# 4 - 300 kcmil
# 4 - 300 kcmil
# 4 - 300 kcmil
#6 - 350 kcmil
#6 - 350 kcmil
# 4 - 300 kcmil
# 4 - 300 kcmil
# 4 - 300 kcmil
250 kcmil -500 kcmil
250 kcmil -500 kcmil
#6 - 350 kcmil
# 4 - 300 kcmil
# 4 - 300 kcmil
250 kcmil -500 kcmil
250 kcmil -500 kcmil
#6 - 350 kcmil
# 4 - 300 kcmil
# 4 - 300 kcmil
250 kcmil -500 kcmil
250 kcmil -500 kcmil
#6 - 350 kcmil
# 4 - 300 kcmil
# 4 - 300 kcmil
250 kcmil -500 kcmil
250 kcmil -500 kcmil
#6 - 350 kcmil
# 4 - 300 kcmil
# 4 - 300 kcmil
35
Table 24, ACZ BC & AGZ BM Electrical Wiring, Single Point (Up to 105°F)
ACZ
Unit
Size
AGZ
Unit
Size
090B
075B
100B
085B
110B
090B
120B
100B
130B
110B
140B
120B
155B
130B
Volts
Minimum
Circuit
Ampacity
(MCA)
208
230
380
460
575
208
230
380
460
575
208
230
380
460
575
208
230
380
460
575
208
230
380
460
575
208
230
380
460
575
208
230
380
460
575
358
358
187
150
125
380
380
219
171
136
414
414
248
188
146
463
463
260
199
171
528
528
282
220
182
613
613
323
248
198
613
613
361
273
212
Power Supply
Field Wire
Wire
Quantity
Gauge
75C
6
4/0
6
4/0
3
3/0
3
1/0
3
#1
6
250
6
250
3
250
3
2/0
3
1/0
6
300
6
300
3
250
3
3/0
3
1/0
6
350
6
300
3
300
3
3/0
3
2/0
6 - (2)
300
6 - (2)
300
3
300
3
4/0
3
3/0
6 - (2)
350
6 - (2)
350
3
400
3
250
3
3/0
6 - (2)
350
6 - (2)
350
6
4/0
3
300
3
4/0
Recomm’d.
Fuse
Or HACR
Breaker
Size
400
400
225
175
150
450
450
250
200
150
500
500
300
225
175
500
500
300
225
175
600
600
300
250
200
700
700
350
250
225
700
700
400
300
225
Max. Fuse
Or HACR
Breaker
Size
400
400
225
175
150
450
450
250
200
150
500
500
300
225
175
500
500
300
225
175
600
600
300
250
200
700
700
350
250
225
700
700
400
300
225
NOTES:
1. Units operating in ambient temperatures of 95°F (35°C) and above must use the Maximum Fuse or HACR
Breaker size.
2. All Electrical Data notes are on page 49.
3. (2) indicates that two conduits are required.
4. Conduit hubs are not supplied.
36
ACZ / AGZ-BM
IMM ACZ/AGZ-4
Table 25, ACZ BC & AGZ BM Compressor and Fan Motor Amps, Single and Multi-Point
(Up to 105°F)
ACZ
Unit
Size
AGZ
Unit
Size
Rated Load Amps
Compressors
Volts
No. 1 No. 3 No. 5 No. 2 No. 4 No. 6
208
73.1 73.1
230
73.1 73.1
090B 075B
380
38.2 38.2
460
30.1 30.1
575
25.2 25.2
208
73.1 73.1
230
73.1 73.1
100B 085B
380
38.2 38.2
460
30.1 30.1
575
25.2 25.2
208
86.4 86.4
230
86.4 86.4
110B 090B
380
52.5 52.5
460
39.0 39.0
575
30.0 30.0
208
52.8 52.8
230
52.8 52.8
120B 100B
380
32.7 32.7
460
23.7 23.7
575
21.8 21.8
208
74.5 74.5
230
74.5 74.5
130B 110B
380
39.8 39.8
460
30.6 30.6
575
25.2 25.2
208
87.9 87.9
230
87.9 87.9
140B 120B
380
39.8 39.8
460
30.6 30.6
575
25.2 25.2
208
88.0 88.0
230
88.0 88.0
155B 130B
380
52.5 52.5
460
39.0 39.0
575
30.0 30.0
All Electrical Data notes are on page
IMM ACZ/AGZ-4
52.8
52.8
32.7
23.7
21.8
74.5
74.5
39.8
30.6
25.2
87.9
87.9
39.8
30.6
25.2
88.0
88.0
52.5
39.0
30.0
49
73.1
73.1
38.2
30.1
25.2
83.3
83.3
52.5
39.0
30.0
86.4
86.4
52.5
39.0
30.0
74.5
74.5
39.8
30.6
25.2
74.5
74.5
39.8
30.6
25.2
88.0
88.0
52.5
39.0
30.0
88.0
88.0
52.5
39.0
30.0
73.1
73.1
38.2
30.1
25.2
83.3
83.3
52.5
39.0
30.0
86.4
86.4
52.5
39.0
30.0
74.5
74.5
39.8
30.6
25.2
74.5
74.5
39.8
30.6
25.2
88.0
88.0
52.5
39.0
30.0
88.0
88.0
52.5
39.0
30.0
74.5
74.5
39.8
30.6
25.2
74.5
74.5
39.8
30.6
25.2
88.0
88.0
52.5
39.0
30.0
88.0
88.0
52.5
39.0
30.0
F.L. No. Of
Fan
Amps
Fan
Fan Motors Motors
(Each) No.1
Motors
(Each)
7.8
6
31.7
505
7.8
6
35.6
505
4.1
6
20.0
280
3.6
6
17.8
225
3.0
6
14.0
180
7.8
6
31.7
505
7.8
6
35.6
505
4.1
6
20.0
280
3.6
6
17.8
225
3.0
6
14.0
180
7.8
6
31.7
500
7.8
6
35.6
500
4.1
6
20.0
305
3.6
6
17.8
250
3.0
6
14.0
198
7.8
8
31.7
425
7.8
8
35.6
425
4.1
8
20.0
239
3.6
8
17.8
187
3.0
8
14.0
148
7.8
8
31.7
505
7.8
8
35.6
505
4.1
8
20.0
280
3.6
8
17.8
225
3.0
8
14.0
180
7.8
8
31.7
505
7.8
8
35.6
505
4.1
8
20.0
280
3.6
8
17.8
225
3.0
8
14.0
180
7.8
8
31.7
500
7.8
8
35.6
500
4.1
8
20.0
305
3.6
8
17.8
250
3.0
8
14.0
198
ACZ / AGZ-BM
Locked Rotor Amps
Compressors
Across-The-Line
No. 3 No. 5
505
505
280
225
180
505
505
280
225
180
500
500
305
250
198
425
425
239
187
148
505
505
280
225
180
505
505
280
225
180
500
500
305
250
198
425
425
239
187
148
505
505
280
225
180
505
505
280
225
180
500
500
305
250
198
No.2
No.4
No. 6
505
505
280
225
180
500
500
305
250
198
500
500
305
250
198
505
505
280
225
180
505
505
280
225
180
500
500
305
250
198
500
500
305
250
198
505
505
280
225
180
500
500
305
250
198
500
500
305
250
198
505
505
280
225
180
505
505
280
225
180
500
500
305
250
198
500
500
305
250
198
505
505
280
225
180
505
505
280
225
180
500
500
305
250
198
500
500
305
250
198
37
Table 26, ACZ BC & AGZ BM Field Wiring, Single Point
ACZ
Unit
Size
AGZ
Unit
Size
090B
075B
100B
085B
110B
090B
120B
100B
130B
110B
140B
120B
155B
130B
All Electrical Data
38
Wiring to Standard
Power Block
Volts
Terminal
Amps
208
760
230
760
380
380
460
380
575
380
208
760
230
760
380
380
460
380
575
380
208
760
230
760
380
380
460
380
575
380
208
760
230
760
380
380
460
380
575
380
208
760
230
760
380
380
460
380
575
380
208
760
230
760
380
380
460
380
575
380
208
760
230
760
380
760
460
380
575
380
notes are on page 49.
Connector Wire
Range
(Copper Wire Only)
2 GA – 500 kcmil
2 GA – 500 kcmil
#4 – 500 kcmil
#4 – 500 kcmil
#4 – 500 kcmil
2 GA – 500 kcmil
2 GA – 500 kcmil
#4 – 500 kcmil
#4 – 500 kcmil
#4 – 500 kcmil
2 GA – 500 kcmil
2 GA – 500 kcmil
#4 – 500 kcmil
#4 – 500 kcmil
#4 – 500 kcmil
2 GA – 500 kcmil
2 GA – 500 kcmil
#4 – 500 kcmil
#4 – 500 kcmil
#4 – 500 kcmil
2 GA – 500 kcmil
2 GA – 500 kcmil
#4 – 500 kcmil
#4 – 500 kcmil
#4 – 500 kcmil
2 GA – 500 kcmil
2 GA – 500 kcmil
#4 – 500 kcmil
#4 – 500 kcmil
#4 – 500 kcmil
2 GA – 500 kcmil
2 GA – 500 kcmil
2 GA – 500 kcmil
#4 – 500 kcmil
#4 – 500 kcmil
ACZ / AGZ-BM
Wiring to Optional
Non-Fused Disconnect Switch
Disconnect
Size
Connector Wire Range
(Copper Wire Only)
600
600
250
250
250
600
600
400
250
250
600
600
400
250
250
600
600
400
400
250
800
800
400
400
400
800
800
400
400
400
800
800
600
400
400
(2) 250 kcmil -500 kcmil
(2) 250 kcmil -500 kcmil
#6 - 350 kcmil
#6 - 350 kcmil
#6 - 350 kcmil
(2) 250 kcmil -500 kcmil
(2) 250 kcmil -500 kcmil
250 kcmil -500 kcmil
#6 - 350 kcmil
#6 - 350 kcmil
(2) 250 kcmil -500 kcmil
(2) 250 kcmil -500 kcmil
250 kcmil -500 kcmil
#6 - 350 kcmil
#6 - 350 kcmil
(2) 250 kcmil -500 kcmil
(2) 250 kcmil -500 kcmil
250 kcmil -500 kcmil
250 kcmil -500 kcmil
#6 - 350 kcmil
(2) 250 kcmil -500 kcmil
(2) 250 kcmil -500 kcmil
250 kcmil -500 kcmil
(2) 3/0-250 kcmil
(2) 3/0-250 kcmil
(2) 250 kcmil -500 kcmil
(2) 250 kcmil -500 kcmil
250 kcmil -500 kcmil
250 kcmil -500 kcmil
(2) 3/0-250 kcmil
(2) 250 kcmil -500 kcmil
(2) 250 kcmil -500 kcmil
(2) 3/0-250 kcmil
250 kcmil -500 kcmil
(2) 3/0-250 kcmil
IMM ACZ/AGZ-4
Table 27, ACZ BC & AGZ BM Electrical Data, Multi-Point (Up to 105°F)
ACZ
Unit
Size
AGZ
Unit
Size
030B 026B
035B 030B
040B 035B
045B 040B
050B 045B
055B 050B
060B 055B
065B 060B
070B 065B
080B 070B
Volts
208
230
380
460
575
208
230
380
460
575
208
230
380
460
575
208
230
380
460
575
208
230
380
460
575
208
230
380
460
575
208
230
380
460
575
208
230
380
460
575
208
230
380
460
575
208
230
380
460
575
Electrical Circuit #1
Electrical Circuit #2
Recomm’d
Power
Supply
Power
Supply Recomm’d
Minimum
Max. Fuse Minimum
Fuse
Fuse
Field
Wire
Field
Wire
Circuit
or HACR
Circuit
or HACR
or HACR
Ampacity
Breaker Ampacity
Wire
Wire
Breaker
Breaker
Qty
Qty
(MCA)
Size
(MCA)
Gauge
Gauge
Size
Size
70
3
#4
80
90
70
3
#4
80
66
3
#4
80
90
66
3
#4
80
42
3
#8
50
50
42
3
#8
50
36
3
#8
45
45
36
3
#8
45
27
3
#10
35
35
27
3
#10
35
70
3
#4
80
90
83
3
#4
100
66
3
#4
80
90
83
3
#4
100
42
3
#8
50
50
50
3
#8
60
36
3
#8
45
45
42
3
#8
50
27
3
#10
35
35
34
3
#10
40
83
3
#4
100
110
83
3
#4
100
79
3
#4
100
100
79
3
#4
100
50
3
#8
60
60
50
3
#8
60
42
3
#8
50
50
42
3
#8
50
34
3
#10
40
45
34
3
#10
40
88
3
#3
110
110
88
3
#3
110
88
3
#3
110
100
88
3
#3
110
60
3
#6
70
80
60
3
#6
70
43
3
#8
50
50
43
3
#8
50
37
3
#8
45
50
37
3
#8
45
88
3
#3
110
110
105
3
#2
125
88
3
#3
110
110
105
3
#2
125
60
3
#6
70
80
67
3
#4
80
43
3
#8
50
50
55
3
#6
70
37
3
#8
45
50
45
3
#8
50
105
3
#2
125
125
105
3
#2
125
105
3
#2
125
125
105
3
#2
125
67
3
#4
80
80
67
3
#4
80
55
3
#6
70
70
55
3
#6
70
45
3
#8
50
60
45
3
#8
50
105
3
#2
125
125
130
3
#1
150
105
3
#2
125
125
120
3
#1
150
67
3
#4
80
80
82
3
#3
100
55
3
#6
70
70
59
3
#6
70
45
3
#8
50
60
55
3
#6
70
130
3
#1
150
175
130
3
#1
150
120
3
#1
150
150
120
3
#1
150
82
3
#3
100
110
82
3
#3
100
59
3
#6
70
80
59
3
#6
70
55
3
#6
70
70
55
3
#6
70
135
3
1/0
175
175
160
3
2/0
200
135
3
1/0
175
175
160
3
2/0
200
82
3
#4
100
110
89
3
#3
110
61
3
#6
70
80
69
3
#4
90
55
3
#6
70
70
59
3
#6
70
160
3
2/0
200
225
160
3
2/0
200
160
3
2/0
200
225
160
3
2/0
200
89
3
#3
110
125
89
3
#3
110
69
3
#4
90
100
69
3
#4
90
59
3
#6
70
80
59
3
#6
70
Max.
Fuse
or HACR
Breaker
Size
90
90
50
45
35
110
100
60
50
45
110
100
60
50
45
110
100
80
50
50
125
125
80
70
60
125
125
80
70
60
175
150
110
80
70
175
150
110
80
70
225
225
125
100
80
225
225
125
100
80
NOTES:
1. All Electrical Data notes are on page 49.
2. Conduit hubs are not supplied.
IMM ACZ/AGZ-4
ACZ / AGZ-BM
39
Table 28, ACZ BC & AGZ BM Field Wiring, Multi-Point
ACZ
Unit
Size
AGZ
Unit
Size
Wiring to Standard
Power Block
Volts
Terminal
Amps
Cir #1
Cir #2
208
175
175
230
175
175
380
175
175
030B
026B
460
175
175
575
175
175
208
175
175
230
175
175
380
175
175
035B
030B
460
175
175
575
175
175
208
175
175
230
175
175
380
175
175
040B
035B
460
175
175
575
175
175
208
175
175
230
175
175
380
175
175
045B
040B
460
175
175
575
175
175
208
175
175
230
175
175
380
175
175
050B
045B
460
175
175
575
175
175
208
175
175
230
175
175
380
175
175
055B
050B
460
175
175
575
175
175
208
175
175
230
175
175
380
175
175
060B
055B
460
175
175
575
175
175
208
175
175
230
175
175
380
175
175
065B
060B
460
175
175
575
175
175
208
380
380
230
380
380
380
175
175
070B
065B
460
175
175
575
175
175
208
380
380
230
380
380
380
175
175
080B
070B
460
175
175
575
175
175
All Electrical Data notes are on page 49.
40
Wiring to Optional
Non-Fused Disconnect Switch
Connector Wire Range
(Copper Wire Only)
Cir #1
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
#4 – 500 kcmil
#4 – 500 kcmil
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
#4 – 500 kcmil
#4 – 500 kcmil
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
Cir #2
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
#4 – 500 kcmil
#4 – 500 kcmil
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
#4 – 500 kcmil
#4 – 500 kcmil
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
ACZ / AGZ-BM
Disconnect Size
Cir #1
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
225
225
150
150
150
225
225
150
150
150
Cir #2
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
225
225
150
150
150
225
225
150
150
150
Connector Wire Range
(Copper Wire Only)
Cir #1
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#4 – 300 kcmil
#4 – 300 kcmil
#14 - 1/0
#14 - 1/0
#14 - 1/0
#4 – 300 kcmil
#4 – 300 kcmil
#14 - 1/0
#14 - 1/0
#14 - 1/0
Cir #2
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#14 - 1/0
#4 – 300 kcmil
#4 – 300 kcmil
#14 - 1/0
#14 - 1/0
#14 - 1/0
#4 – 300 kcmil
#4 – 300 kcmil
#14 - 1/0
#14 - 1/0
#14 - 1/0
IMM ACZ/AGZ-4
Table 29, ACZ BC & AGZ BM Field Wiring Data
ACZ
Unit
Size
AGZ
Unit
Size
Wiring to Standard
Power Block
Volts
Terminal
Amps
Cir #1 Cir #2
208
380
380
230
380
380
380
175
175
090B
075B
460
175
175
575
175
175
208
380
380
230
380
380
380
175
175
100B
085B
460
175
175
575
175
175
208
380
380
230
380
380
380
175
175
110B
090B
460
175
175
575
175
175
208
380
380
230
380
380
380
175
175
120B
100B
460
175
175
575
175
175
208
380
380
230
380
380
380
380
380
130B
110B
460
380
380
575
175
175
208
380
380
230
380
380
380
380
380
140B
120B
460
380
380
575
175
175
208
380
380
230
380
380
380
380
380
155B
130B
460
380
380
575
175
175
All Electrical Data notes are on page 49.
IMM ACZ/AGZ-4
Wiring to Optional
Non-Fused Disconnect Switch
Connector Wire Range
(Copper Wire Only)
Cir #1
#4 – 500 kcmil
#4 – 500 kcmil
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
#4 – 500 kcmil
#4 – 500 kcmil
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
#4 – 500 kcmil
#4 – 500 kcmil
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
#4 – 500 kcmil
#4 – 500 kcmil
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
#4 – 500 kcmil
#4 – 500 kcmil
#4 – 500 kcmil
#4 – 500 kcmil
14 GA – 2/0
#4 – 500 kcmil
#4 – 500 kcmil
#4 – 500 kcmil
#4 – 500 kcmil
14 GA – 2/0
#4 – 500 kcmil
#4 – 500 kcmil
#4 – 500 kcmil
#4 – 500 kcmil
14 GA – 2/0
Cir #2
#4 – 500 kcmil
#4 – 500 kcmil
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
#4 – 500 kcmil
#4 – 500 kcmil
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
#4 – 500 kcmil
#4 – 500 kcmil
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
#4 – 500 kcmil
#4 – 500 kcmil
14 GA – 2/0
14 GA – 2/0
14 GA – 2/0
#4 – 500 kcmil
#4 – 500 kcmil
#4 – 500 kcmil
#4 – 500 kcmil
14 GA – 2/0
#4 – 500 kcmil
#4 – 500 kcmil
#4 – 500 kcmil
#4 – 500 kcmil
14 GA – 2/0
#4 – 500 kcmil
#4 – 500 kcmil
#4 – 500 kcmil
#4 – 500 kcmil
14 GA – 2/0
ACZ / AGZ-BM
Disconnect Size
Cir #1
250
250
250
150
150
250
250
250
150
150
250
250
250
150
150
250
250
150
150
150
400
400
250
250
150
400
400
250
250
150
400
400
250
250
150
Cir #2
250
250
250
150
150
250
250
250
150
150
250
250
250
150
150
400
400
250
250
150
400
400
250
250
150
400
400
250
250
150
400
400
250
250
150
Connector Wire Range
(Copper Wire Only)
Cir #1
#4 – 300 kcmil
#4 – 300 kcmil
#4 – 300 kcmil
#14 - 1/0
#14 - 1/0
#4 – 300 kcmil
#4 – 300 kcmil
#4 – 300 kcmil
#14 - 1/0
#14 - 1/0
#4 – 300 kcmil
#4 – 300 kcmil
#4 – 300 kcmil
#14 - 1/0
#14 - 1/0
#4 – 300 kcmil
#4 – 300 kcmil
#14 - 1/0
#14 - 1/0
#14 - 1/0
250 – 500
250 – 500
#4 – k300ilkcmil
#4 – 300 kcmil
#14 - 1/0
250 – 500
250 – 500
#4 – k300ilkcmil
#4 – 300 kcmil
#14 - 1/0
250 – 500
250 – 500
#4 – k300ilkcmil
#4 – 300 kcmil
#14 - 1/0
Cir #2
#4 – 300 kcmil
#4 – 300 kcmil
#4 – 300 kcmil
#14 - 1/0
#14 - 1/0
#4 – 300 kcmil
#4 – 300 kcmil
#4 – 300 kcmil
#14 - 1/0
#14 - 1/0
#4 – 300 kcmil
#4 – 300 kcmil
#4 – 300 kcmil
#14 - 1/0
#14 - 1/0
250 – 500 kcmil
250 - 500 kcmil
#4 – 300 kcmil
#4 – 300 kcmil
#14 - 1/0
250 – 500 kcmil
250 - 500kcmil
#4 - 300kcmil
#4 - 300kcmil
#14 - 1/0
250 - 500 kcmil
250 – 500 kcmil
#4 – 300 kcmil
#4 – 300 kcmil
#14 - 1/0
250 – 500 kcmil
250 – 500 kcmil
#4 – 300 kcmil
#4 – 300 kcmil
#14 - 1/0
41
Table 30, ACZ BC & AGZ BM Electrical Data, Multi-Point (Up to 105°F)
Electrical Circuit #1
Electrical Circuit #2
Power
Power
Recomm’d
Recomm’d
Max.
Supply
Supply
Minimum
Max. Fuse Minimum
ACZ AGZ
Fuse
Fuse
Fuse
Unit Volts Circuit
or HACR
Circuit
Field Wire
Field Wire
Unit
or HACR
or HACR or HACR
Ampacity
Breaker Ampacity
Wire
Wire
Size Size
Breaker
Breaker
Breaker
(MCA)
Size
(MCA)
Qty Gauge
Qty Gauge
Size
Size
Size
75C
75C
208
188
3
3/0
225
250
188
3
3/0
225
250
230
188
3
3/0
225
250
188
3
3/0
225
250
98
3
#3
110
125
98
3
#3
110
125
090B 075B 380
460
79
3
#4
90
110
79
3
#4
90
110
575
66
3
#4
80
90
66
3
#4
80
90
208
188
3
3/0
225
250
218
3
4/0
250
300
230
188
3
3/0
225
250
218
3
4/0
250
250
98
3
#3
110
125
130
3
#1
150
175
100B 085B 380
460
79
3
#4
90
110
99
3
#3
125
125
575
66
3
#4
80
90
77
3
#4
90
100
208
218
3
4/0
250
300
218
3
4/0
250
300
230
218
3
4/0
250
250
218
3
4/0
250
250
130
3
#1
150
175
130
3
#1
150
175
110B 090B 380
460
99
3
#3
125
125
99
3
#3
125
125
575
77
3
#4
90
100
77
3
#4
90
100
208
203
3
4/0
250
250
273
3
300
300
300
230
203
3
3/0
225
225
273
3
300
300
300
123
3
#1
150
150
146
3
1/0
175
200
120B 100B 380
460
92
3
#3
110
110
114
3
#1
150
175
575
83
3
#4
100
100
94
3
#3
110
125
208
273
3
300
300
300
273
3
300
300
300
230
273
3
300
300
300
273
3
300
300
300
146
3
1/0
175
175
146
3
1/0
175
175
130B 110B 380
460
114
3
#1
125
125
114
3
#1
125
125
575
94
3
#3
110
110
94
3
#3
110
110
208
317
3
300
400
400
317
3
400
400
400
230
317
3
300
400
400
318
3
400
400
400
146
3
1/0
175
175
187
3
2/0
225
225
140B 120B 380
460
114
3
#1
125
125
141
3
1/0
175
175
575
94
3
#3
110
110
110
3
#2
125
125
208
317
3
400
400
400
317
3
400
400
400
230
318
3
400
400
400
318
3
400
400
400
187
3
2/0
225
225
187
3
2/0
225
225
155B 130B 380
460
141
3
1/0
175
175
141
3
1/0
175
175
575
110
3
#2
125
125
110
3
#2
125
125
NOTES:
1.
All Electrical Data notes are on page 49.
2.
Conduit hubs are not supplied.
42
ACZ / AGZ-BM
IMM ACZ/AGZ-4
Electrical Data High Ambient
Table 31, ACZ BC & AGZ BM Electrical Data, Single Point
ACZ Unit
Size
AGZ
Unit
Size
030B
026B
035B
030B
040B
035B
045B
040B
050B
045B
055B
050B
060B
055B
065B
060B
070B
065B
080B
070B
Volts
Minimum
Circuit
Ampacity
(MCA)
208
230
380
460
575
208
230
380
460
575
208
230
380
460
575
208
230
380
460
575
208
230
380
460
575
208
230
380
460
575
208
230
380
460
575
208
230
380
460
575
208
230
380
460
575
208
230
380
460
575
147
133
80
68
53
158
144
88
74
59
168
155
96
80
64
187
167
113
84
70
207
188
123
94
78
226
207
132
104
86
249
229
147
115
96
270
248
160
124
105
303
282
164
138
115
323
304
172
150
123
Power Supply
Field Wire
Wire
Quantity
Gauge
75C
3
1/0
3
1/0
3
#4
3
#4
3
#6
3
2/0
3
1/0
3
#3
3
#4
3
#6
3
2/0
3
2/0
3
#3
3
#4
3
#6
3
3/0
3
2/0
3
#2
3
#4
3
#4
3
4/0
3
3/0
3
#1
3
#3
3
#4
3
4/0
3
3/0
3
1/0
3
#2
3
#3
3
250
3
4/0
3
1/0
3
#2
3
#3
3
300
3
250
3
2/0
3
#1
3
#2
3
350
3
300
3
2/0
3
1/0
3
#2
3
400
3
350
3
2/0
3
1/0
3
#1
Recomm’d.
Fuse
Or HACR
Breaker
Size
Max. Fuse
Or HACR
Breaker
Size
175
150
90
80
60
175
175
100
90
70
200
175
110
90
70
200
200
125
90
80
225
225
125
110
90
225
225
150
125
100
250
250
175
125
110
300
250
175
150
125
350
350
200
175
125
400
350
200
175
150
175
150
90
80
60
175
175
100
90
70
200
175
110
90
70
200
200
125
90
80
225
225
125
110
90
225
225
150
125
100
250
250
175
125
110
300
250
175
150
125
350
350
200
175
125
400
350
200
175
150
NOTES:
1.
Units operating in ambient temperatures above 95°F (35°C) must use the Maximum Fuse or HACR Breaker size
2.
All Electrical Data notes are on page 49.
3.
Conduit hubs are not provided.
IMM ACZ/AGZ-4
ACZ / AGZ-BM
43
Table 32, ACZ BC & AGZ BM Compressor & Fan Motor Amps, Single & Multi-Point
(106°F to 125°F)
ACZ
Unit
Size
AGZ
Unit
Size
030B
026B
035B
030B
040B
035B
045B
040B
050B
045B
055B
050B
060B
055B
065B
060B
070B
065B
080B
070B
All Electrical
44
Rated Load Amps
Compressors
No.
F.L.Amps
R.L.Amps
of
Volts
Fan
Fan
Fan
No. 1 No. 3 No. 5 No. 2 No. 4 No. 6 Motors Motors Motors
No.1
(Each)
(Each)
208
29.0
230
25.7
380
14.9
460
13.4
575
9.5
208
29.0
230
25.7
380
14.9
460
13.4
575
9.5
208
34.0
230
30.9
380
18.6
460
16.2
575
12.2
208
38.5
230
33.8
380
22.8
460
17.0
575
13.7
208
38.5
230
33.8
380
22.8
460
17.0
575
13.7
208
47.6
230
43.3
380
27.2
460
21.8
575
17.3
208
47.6
230
43.3
380
27.2
460
21.8
575
17.3
208
58.1
230
52.8
380
33.8
460
26.5
575
21.8
208
58.1
230
52.8
380
32.7
460
25.5
575
21.8
208
58.1
230
52.8
380
32.7
460
25.5
575
21.8
Data notes are
29.0
25.7
14.9
13.4
9.5
29.0
25.7
14.9
13.4
9.5
34.0
30.9
18.6
16.2
12.2
38.5
33.8
22.8
17.0
13.7
38.5
33.8
22.8
17.0
13.7
47.6
43.3
27.2
21.8
17.3
47.6
43.3
27.2
21.8
17.3
58.1
52.8
33.8
26.5
21.8
58.1
52.8
32.7
25.5
21.8
78.0
74.1
39.8
37.5
29.9
on page
49.
29.0
25.7
14.9
13.4
9.5
34.0
30.9
18.6
16.2
12.2
34.0
30.9
18.6
16.2
12.2
38.5
33.8
22.8
17.0
13.7
47.6
43.3
27.2
21.8
17.3
47.6
43.3
27.2
21.8
17.3
58.1
52.8
33.8
26.5
21.8
58.1
52.8
33.8
26.5
21.8
58.1
52.8
32.7
25.5
21.8
58.1
52.8
32.7
25.5
21.8
29.0
25.7
14.9
13.4
9.5
34.0
30.9
18.6
16.2
12.2
34.0
30.9
18.6
16.2
12.2
38.5
33.8
22.8
17.0
13.7
47.6
43.3
27.2
21.8
17.3
47.6
43.3
27.2
21.8
17.3
58.1
52.8
33.8
26.5
21.8
58.1
52.8
33.8
26.5
21.8
78.0
74.1
39.8
37.5
29.9
78.0
74.1
39.8
37.5
29.9
-
5.8
5.8
4.1
2.8
3.0
5.8
5.8
4.1
2.8
3.0
5.8
5.8
4.1
2.8
3.0
5.8
5.8
4.1
2.8
3.0
5.8
5.8
4.1
2.8
3.0
5.8
5.8
4.1
2.8
3.0
5.8
5.8
4.1
2.8
3.0
5.8
5.8
4.1
2.8
3.0
7.8
7.8
4.1
3.6
3.0
7.8
7.8
4.1
3.6
3.0
ACZ / AGZ-BM
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
23.3
26.1
20.0
13.0
14.0
23.3
26.1
20.0
13.0
14.0
23.3
26.1
20.0
13.0
14.0
23.3
26.1
20.0
13.0
14.0
23.3
26.1
20.0
13.0
14.0
23.3
26.1
20.0
13.0
14.0
23.3
26.1
20.0
13.0
14.0
23.3
26.1
20.0
13.0
14.0
31.7
35.6
20.0
17.8
14.0
31.7
35.6
20.0
17.8
14.0
189
189
112
99
74
189
189
112
99
74
232
232
144
125
100
278
278
151
127
100
278
278
151
127
100
350
350
195
158
125
350
350
195
158
125
425
425
239
187
148
425
425
239
187
148
425
425
239
187
148
Locked Rotor Amps
Compressors
Across-The-Line
No. 3 No. 5
189
189
112
99
74
189
189
112
99
74
232
232
144
125
100
278
278
151
127
100
278
278
151
127
100
350
350
195
158
125
350
350
195
158
125
425
425
239
187
148
425
425
239
187
148
505
505
280
225
180
-
No.2
No.4
No. 6
189
189
112
99
74
232
232
144
125
100
232
232
144
125
100
278
278
151
127
100
350
350
195
158
125
350
350
195
158
125
425
425
239
187
148
425
425
239
187
148
425
425
239
187
148
425
425
239
187
148
189
189
112
99
74
232
232
144
125
100
232
232
144
125
100
278
278
151
127
100
350
350
195
158
125
350
350
195
158
125
425
425
239
187
148
425
425
239
187
148
505
505
280
225
180
505
505
280
225
180
-
IMM ACZ/AGZ-4
Table 33, ACZ BC & AGZ BM Electrical Data, Multi-Point (106°F to 125°F)
ACZ
Unit
Size
AGZ
Unit
Size
030B 026B
035B 030B
040B 035B
045B 040B
050B 045B
055B 050B
060B 055B
065B 060B
070B 065B
080B 070B
Volts
208
230
380
460
575
208
230
380
460
575
208
230
380
460
575
208
230
380
460
575
208
230
380
460
575
208
230
380
460
575
208
230
380
460
575
208
230
380
460
575
208
230
380
460
575
208
230
380
460
575
Electrical Circuit #1
Electrical Circuit #2
Power Supply Recomm’d
Power Supply Recomm’d
Minimum
Max. Fuse Minimum
Fuse
Fuse
Field Wire
Field Wire
Circuit
or HACR
Circuit
or
HACR
or HACR
Wire
Wire
Ampacity
Breaker Ampacity
Breaker
Qty Gauge Breaker
Qty Gauge
(MCA)
Size
(MCA)
Size
Size
75C
75C
77
3
#4
90
100
77
3
#4
90
70
3
#4
80
90
70
3
#4
80
42
3
#8
50
50
40
3
#8
50
36
3
#8
45
45
36
3
#8
45
27
3
#10
35
35
27
3
#10
35
77
3
#4
90
100
88
3
#3
100
70
3
#4
80
90
81
3
#4
100
42
3
#8
50
50
50
3
#8
60
36
3
#8
45
45
42
3
#8
50
27
3
#10
35
35
34
3
#10
45
88
3
#3
100
110
88
3
#3
100
81
3
#4
100
110
81
3
#4
100
50
3
#8
60
60
50
3
#8
60
42
3
#8
50
50
42
3
#8
50
34
3
#10
45
45
34
3
#10
45
98
3
#3
125
125
98
3
#3
125
88
3
#3
110
110
88
3
#3
110
60
3
#6
70
80
60
3
#6
70
44
3
#8
50
60
44
3
#8
50
37
3
#8
45
50
37
3
#8
45
98
3
#3
125
125
119
3
#1
150
88
3
#3
110
110
109
3
#2
125
60
3
#6
70
80
70
3
#4
80
44
3
#8
50
60
55
3
#6
70
37
3
#8
45
50
45
3
#8
60
119
3
#1
150
150
119
3
#1
150
109
3
#2
125
150
109
3
#2
125
70
3
#4
80
90
70
3
#4
80
55
3
#6
70
70
55
3
#6
70
45
3
#8
60
60
45
3
#8
60
119
3
#1
150
150
142
3
1/0
175
109
3
#2
125
150
130
3
#1
175
70
3
#4
80
90
84
3
#4
100
55
3
#6
70
70
65
3
#4
80
45
3
#8
60
60
55
3
#6
70
142
3
1/0
175
200
142
3
1/0
175
130
3
#1
175
175
130
3
#1
175
84
3
#4
100
110
84
3
#4
100
65
3
#4
80
90
65
3
#4
80
55
3
#6
70
70
55
3
#6
70
146
3
1/0
175
200
171
3
2/0
225
134
3
1/0
175
175
161
3
2/0
200
82
3
#4
100
110
91
3
#3
110
67
3
#6
80
90
80
3
#4
100
55
3
#6
70
70
65
3
#6
90
171
3
2/0
225
225
171
3
2/0
225
161
3
2/0
200
225
161
3
2/0
200
91
3
#3
110
125
91
3
#3
110
80
3
#4
100
110
80
3
#4
100
65
3
#6
90
90
65
3
#6
90
Max.
Fuse
or HACR
Breaker
Size
100
90
50
45
35
110
110
60
50
45
110
110
60
50
45
125
110
80
60
50
150
150
90
70
60
150
150
90
70
60
200
175
110
90
70
200
175
110
90
70
225
225
125
110
90
225
225
125
110
90
Notes:
1. All Electrical Data notes are on page 49.
2. Conduit hubs are not supplied.
IMM ACZ/AGZ-4
ACZ / AGZ-BM
45
Table 34, ACZ BC & AGZ BM Electrical Data, Single Point (Above 105°F)
ACZ
Unit
Size
AGZ
Unit
Size
090B
075B
100B
085B
110B
090B
120B
100B
130B
110B
140B
120B
155B
130B
Volts
Minimum
Circuit
Ampacity
(MCA)
208
230
380
460
575
208
230
380
460
575
208
230
380
460
575
208
230
380
460
575
208
230
380
460
575
208
230
380
460
575
208
230
380
460
575
378
362
194
187
145
398
382
234
200
151
416
414
270
211
157
522
463
273
230
187
612
528
307
263
211
613
613
352
286
219
613
613
393
307
228
Power Supply
Field Wire
Wire
Quantity
Gauge
75C
6
250
6
4/0
3
3/0
3
3/0
3
1/0
6
250
6
250
3
250
3
4/0
3
1/0
6
300
6
300
3
300
3
4/0
3
2/0
6
400
6
350
3
300
3
4/0
3
3/0
6 - (2)
350
6 - (2)
300
3
350
3
300
3
4/0
6 - (2)
350
6 - (2)
350
6 - (2)
4/0
3
350
3
4/0
6 - (2)
350
6 - (2)
350
6
250
3
350
3
250
Recomm’d.
Fuse
Or HACR
Breaker
Size
450
400
225
225
175
450
450
250
225
175
500
500
300
250
175
600
500
300
250
200
700
600
350
300
225
700
700
400
300
250
700
700
450
350
250
Max. Fuse
Or HACR
Breaker
Size
450
400
225
225
175
450
450
250
225
175
500
500
300
250
175
600
500
300
250
200
700
600
350
300
225
700
700
400
300
250
700
700
450
350
250
NOTES:
1. Units operating in ambient temperatures of 95°F (35°C) and above must use the Maximum Fuse or HACR
Breaker size.
2. All Electrical Data notes are on page 49.
3. (2) in column with wire qty. indicates that two conduits are required.
4. Conduit hubs are not supplied.
46
ACZ / AGZ-BM
IMM ACZ/AGZ-4
Table 35, ACZ BC & AGZ BM Compressor and Fan Motor Amps, Single & Multi-Point
(106°F to 125°F
ACZ
Unit
Size
AGZ
Unit
Size
090B
075B
100B
085B
110B
090B
120B
100B
130B
110B
140B
120B
155B
130B
All Electrical
IMM ACZ/AGZ-4
Rated Load Amps
Compressors
No.
F.L.Amps
R.L.Amps
of
Volts
Fan
Fan
Fan
No. 1 No. 3 No. 5 No. 2 No. 4 No. 6 Motors Motors Motors
(Each)
(Each)
208
78.0
230
74.1
380
39.8
460
38.8
575
29.9
208
78.0
230
74.1
380
39.8
460
38.8
575
29.9
208
86.9
230
86.4
380
57.6
460
44.5
575
32.5
208
58.1
230
52.8
380
32.7
460
25.5
575
21.8
208
87.9
230
74.5
380
43.8
460
37.5
575
29.9
208
87.9
230
87.9
380
43.8
460
37.5
575
29.9
208
88.0
230
88.0
380
57.6
460
44.5
575
32.5
Data notes are
78.0
74.1
39.8
38.8
29.9
78.0
74.1
39.8
38.8
29.9
86.9
86.4
57.6
44.5
32.5
58.1 58.1
52.8 52.8
32.7 32.7
25.5 25.5
21.8 21.8
87.9 87.9
74.5 74.5
43.8 43.8
37.5 37.5
29.9 29.9
87.9 87.9
87.9 87.9
43.8 43.8
37.5 37.5
29.9 29.9
88.0 88.0
88.0 88.0
57.6 57.6
44.5 44.5
32.5 32.5
on page 49.
78.0
74.1
39.8
38.8
29.9
86.9
83.3
57.6
44.5
32.5
86.9
86.4
57.6
44.5
32.5
87.9
74.5
43.8
37.5
29.9
87.9
74.5
43.8
37.5
29.9
88.0
88.0
57.6
44.5
32.5
88.0
88.0
57.6
44.5
32.5
78.0
74.1
39.8
38.8
29.9
86.9
83.3
57.6
44.5
32.5
86.9
86.4
57.6
44.5
32.5
87.9
74.5
43.8
37.5
29.9
87.9
74.5
43.8
37.5
29.9
88.0
88.0
57.6
44.5
32.5
88.0
88.0
57.6
44.5
32.5
87.9
74.5
43.8
37.5
29.9
87.9
74.5
43.8
37.5
29.9
88.0
88.0
57.6
44.5
32.5
88.0
88.0
57.6
44.5
32.5
7.8
7.8
4.1
3.6
3.0
7.8
7.8
4.1
3.6
3.0
7.8
7.8
4.1
3.6
3.0
7.8
7.8
4.1
3.6
3.0
7.8
7.8
4.1
3.6
3.0
7.8
7.8
4.1
3.6
3.0
7.8
7.8
4.1
3.6
3.0
ACZ / AGZ-BM
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
31.7
35.6
20.0
17.8
14.0
31.7
35.6
20.0
17.8
14.0
31.7
35.6
20.0
17.8
14.0
31.7
35.6
20.0
17.8
14.0
31.7
35.6
20.0
17.8
14.0
31.7
35.6
20.0
17.8
14.0
31.7
35.6
20.0
17.8
14.0
Locked Rotor Amps
Compressors
Across-The-Line
No.1
505
505
280
225
180
505
505
280
225
180
500
500
305
250
198
425
425
239
187
148
505
505
280
225
180
505
505
280
225
180
500
500
305
250
198
No. 3 No. 5
505
505
280
225
180
505
505
280
225
180
500
500
305
250
198
425
425
239
187
148
505
505
280
225
180
505
505
280
225
180
500
500
305
250
198
425
425
239
187
148
505
505
280
225
180
505
505
280
225
180
500
500
305
250
198
No.2
No.4
No. 6
505
505
280
225
180
500
500
305
250
198
500
500
305
250
198
505
505
280
225
180
505
505
280
225
180
500
500
305
250
198
500
500
305
250
198
505
505
280
225
180
500
500
305
250
198
500
500
305
250
198
505
505
280
225
180
505
505
280
225
180
500
500
305
250
198
500
500
305
250
198
505
505
280
225
180
505
505
280
225
180
500
500
305
250
198
500
500
305
250
198
47
Table 36, ACZ BC & AGZ BM Electrical Data, Multi-Point (106°F)
Electrical Circuit #1
Electrical Circuit #2
Power
Power
Recomm’d
Recomm’d
Max.
ACZ AGZ
Supply
Supply
Minimum
Max. Fuse Minimum
Fuse
Fuse
Fuse
Unit Unit Volts Circuit
or HACR
Circuit
Field Wire
Field Wire
or HACR
or HACR or HACR
Size Size
Ampacity
Breaker Ampacity
Wire
Wire
Breaker
Breaker
Breaker
(MCA)
Size
(MCA)
Qty Gauge
Qty Gauge
Size
Size
Size
75C
75C
208
199
3
3/0
225
250
199
3
3/0
225
250
230
190
3
3/0
225
250
190
3
3/0
225
250
102
3
#2
125
125
102
3
#2
125
125
090B 075B 380
460
99
3
#3
110
125
99
3
#3
110
125
575
76
3
#4
90
100
76
3
#4
90
100
208
199
3
3/0
225
250
219
3
4/0
250
300
230
190
3
3/0
225
250
211
3
4/0
250
250
102
3
#2
125
125
142
3
1/0
175
175
100B 085B 380
460
99
3
#3
110
125
111
3
#2
125
150
575
76
3
#4
90
100
83
3
#3
100
110
208
219
3
4/0
250
300
219
3
4/0
250
300
230
212
3
4/0
250
300
211
3
4/0
250
300
142
3
1/0
175
175
142
3
1/0
175
175
110B 090B 380
460
111
3
#2
125
150
111
3
#2
125
150
575
83
3
#3
100
110
83
3
#3
100
110
208
220
3
4/0
250
250
317
3
400
350
400
230
203
3
4/0
225
250
273
3
300
300
300
123
3
#1
150
150
159
3
2/0
175
200
120B 100B 380
460
101
3
#2
110
125
136
3
1/0
150
175
575
83
3
#4
100
100
109
3
#2
125
125
208
317
3
400
350
400
317
3
400
350
400
230
273
3
300
300
300
273
3
300
300
300
159
3
2/0
175
200
159
3
2/0
175
200
130B 110B 380
460
136
3
1/0
150
175
136
3
1/0
150
175
575
109
3
#2
125
125
109
3
#2
125
125
208
317
3
400
400
400
317
3
400
400
400
230
273
3
300
400
400
317
3
400
400
400
159
3
2/0
200
200
204
3
4/0
250
250
140B 120B 380
460
136
3
1/0
175
175
159
3
2/0
200
200
575
109
3
#2
125
125
118
3
#1
150
150
208
317
3
400
400
400
317
3
400
400
400
230
317
3
400
400
400
317
3
400
400
400
204
3
4/0
250
250
204
3
4/0
250
250
155B 130B 380
460
159
3
2/0
200
200
159
3
2/0
200
200
575
118
3
#1
150
150
118
3
#1
150
150
NOTES:
1.
All Electrical Data notes are on page 49.
2.
Conduit hubs are not supplied.
48
ACZ / AGZ-BM
IMM ACZ/AGZ-4
Notes for “Electrical Data Single- and Multi-Point” Power:
1. Unit wire size ampacity (MCA) is equal to 125% of the largest compressor-motor RLA
plus 100% of RLA of all other loads in the circuit including the control transformer.
2. The control transformer is furnished on the unit and no separate 115V power is required.
For both single- and multi-point power connections, the control transformer is in circuit
#1 with control power wired from there to circuit #2. In multi-point power,
disconnecting power to circuit will disconnect all control power to the unit.
3. If a separate 115V power supply is used for the control circuit, then the wire sizing amps
is 10 amps for all unit sizes.
4. Recommended power lead wire sizes for 3 conductors per conduit are based on 100%
conductor ampacity in accordance with NEC. Voltage drop has not been included.
Therefore, it is recommended that power leads be kept short. All terminal block
connections must be made with copper (type THW) wire.
5. “Recommended Fuse Sizes” are selected at approximately 150% to 175% of the largest
compressor RLA, plus 100% of all other loads in the circuit.
6. “Maximum Fuse or HACR breaker size” is selected at approximately 225% of the
largest compressor RLA, plus 100% of all other loads in the circuit.
7. The recommended power lead wire sizes are based on an ambient temperature of 86°F
(30°C). Ampacity correction factors must be applied for other ambient temperatures.
Refer to the National Electrical Code Handbook.
8. Must be electrically grounded according to national and local electrical codes.
Voltage Limitations:
Within ± 10 percent of nameplate rating.
Notes for “Compressor and Condenser Fan Amp Draw”:
1. Compressor RLA values are for wiring sizing purposes only but do not reflect normal
operating current draw at rated capacity.
Notes for “Field Wiring Data”
1. Requires a single disconnect to supply electrical power to the unit. This power supply
must either be fused or use an HACR type circuit breaker.
2. All field wiring to unit power block or optional non-fused disconnect switch must be
copper.
3. All field wire size values given in table apply to 75°C rated wire per NEC.
Circuit Breakers
Factory installed circuit breakers are standard on units with single point power supply only. This
option provides unit installed compressor short circuit protection and makes servicing easier.
IMM ACZ/AGZ-4
Connection Type
Power Block
Single Point (Standard)
Multi-Point (Optional)
Std
Std
Disconnect
Swt.
Opt.
Opt.
ACZ / AGZ-BM
Circuit
Breakers
Std
Not Avail.
High Short
Circuit Current
Opt
Opt.
49
Figure 24, AGZ-BM, Typical Field Wiring Diagram
DISCONNECT
(BY OTHERS)
UNIT MAIN
TERMINAL BLOCK
GND LUG
3 PHASE
TO COMPRESSOR(S)
AND FAN MOTORS
POWER
NOTE: ALL FIELD WIRING TO BE
INSTALLED AS NEC CLASS 1
WIRING SYSTEM WITH CONDUCTOR
RATED 600 VOLTS
FIELD SUPPLIED
OPTION
FUSED CONTROL
CIRCUIT TRANSFORMER
120 VAC
DISCONNECT
(BY OTHERS)
TB1-20
N
10A
FUSE
120VAC
CONTROL POWER
(BY OTHERS)
TB1
1
CONTROL
CIRCUIT
FUSE
2
35
120 VAC
N
33
CHW PUMP RELAY
(BY OTHERS)
120 VAC 1.0 AMP MAX
ALARM BELL
OPTION
CONTROLLER
FACTORY SUPPLIED ALARM
FIELD WIRED
120 VAC
34
ALARM BELL RELAY
32
TIME
CLOCK
REMOTE STOP SWITCH
(BY OTHERS)
TB2
ON
52
IF REMOTE STOP
CONTROL IS USED,
REMOVE LEAD 585
FROM TERM. 52
TO 72.
585
72
MANUAL
OFF
ALARM BELL
RELAY
43
COM
NO
BELL
AUTO
ICE MODE SWITCH
(BY OTHERS)
GND
OFF
AUTO
1
83
ON
2
ALARM BELL OPTION
54
74
MANUAL
CHW FLOW SWITCH
---MANDATORY–(BY OTHERS)
44
NOR. OPEN PUMP AUX.
CONTACTS (OPTIONAL)
61
4-20MA FOR
EVAP. WATER RESET
(BY OTHERS)
+
4-20MA FOR
DEMAND LIMIT
(BY OTHERS)
+
68
-
69
70
-
71
GND
LESS EVAPORATOR ONLY
24 VAC
91
93
N
LIQUID LINE #1 SOLENOID
24 VAC 1.5 AMP MAX
24 VAC
92
93
DWG. 330423101 REV.0A
50
N
LIQUID LINE #2 SOLENOID
24 VAC 1.5 AMP MAX
ACZ / AGZ-BM
IMM ACZ/AGZ-4
Figure 25, ACZ-B, Typical Field Wiring Diagram
UNIT MAIN
TERMINAL BLOCK
DISCONNECT
(BY OTHERS)
GND LUG
3 PHASE
TO COMPRESSOR(S)
POWER
AND FAN MOTORS
NOTE 1:
ALL FIELD WIRING TO BE
INSTALLED AS NEC CLASS 1
WIRING SYSTEM WITH CONDUCTOR
RATED 600 VOLTS
FUSED CONTROL
CIRCUIT TRANSFORMER
120 VAC
FIELD SUPPLIED
OPTION
DISCONNECT
(BY OTHERS)
TB1-20
N
10A
FUSE
120VAC
CONTROL POWER
TB1
1
(BY OTHERS)
CONTROL
CIRCUIT
FUSE
2
120 VAC
35
N
33
DX EVAP FAN RELAY
(BY OTHERS)
120 VAC 1.0 AMP MAX
FACTORY SUPPLIED ALARM
FIELD WIRED
ALARM BELL
OPTION
CONTROLLER
120 VAC
34
ALARM BELL RELAY
32
TIME
CLOCK
REMOTE STOP SWITCH
(BY OTHERS)
GND
AUTO OFF
TB2
ON
52
585
72
MANUAL
EVAP FLOW SWITCH
---MANDATORY–(BY OTHERS)
IF REMOTE STOP
CONTROL IS USED,
REMOVE LEAD 585
FROM TERM. 52 TO 72.
ALARM BELL
RELAY
43
COM
83
1
2
NO
ALARM BELL OPTION
44
NOR. OPEN PUMP AUX.
CONTACTS (OPTIONAL)
61
54
(SEE NOTE 2)
4-20MA FOR
DEMAND LIMIT
(BY OTHERS)
J20-ID18
+
-
70
71
GND
NOTE 2:
EVAP. AIR FLOW SWITCH OR
FAN AUX. CONTACT FOR
CIRCUIT #2 FAN WHEN UNIT IS
SET FOR CIRCUIT SEQUENCING
MODE.
LESS EVAPORATOR ONLY
24 VAC
91
93
N
LIQUID LINE #1 SOLENOID
24 VAC 1.5 AMP MAX.
24 VAC
92
93
N
LIQUID LINE #2 SOLENOID
24 VAC 1.5 AMP MAX.
24 VAC
95
97
N
HOT GAS BYPASS #1 SOLENOID
24 VAC 1.0 AMP MAX.
24 VAC
96
97
N
HOT GAS BYPASS #2 SOLENOID
24 VAC 1.0 AMP MAX.
STAGING OPERATION IN UNIT
SEQUENCING SETTING
STAGE 1
1ST COMPR. - EITHER CIRCUIT
NOTE 3:
WHEN CONNECTED TO
EVAPORATORS USING
OPTIONAL CIRCUIT CONTROL,
STAGES 1-3 ACTIVATE
COMPRESSORS FOR
CONDENSING UNIT CIRCUIT #1
AND STAGES 4-6 ACTIVATE
COMPRESSORS FOR
CONDENSING UNIT CIRCUIT #2.
STAGE 2
1 ST COMPR. - OPPOSITE CIRCUIT
STAGE 3
2 ND COMPR. - INITIAL CIRCUIT
STAGE 4
2
ND
STAGING OPERATION IN CIRCUIT
SEQUENCING SETTING
TB3
101
STAGE 1
1 ST COMPR. - CIRCUIT #1
STAGE 2
102
ND
2
104
105
106
STAGE 5
STAGE 3
3RD COMPR. - CIRCUIT #1
STAGE 4
3 RD COMPR. - INITIAL CIRCUIT
STAGE 6
3 RD COMPR. - OPPOSITE CIRCUIT
1 ST COMPR. - CIRCUIT #2
108
109
110
111
112
102
COMPR. - CIRCUIT #1
107
COMPR. - OPPOSITE CIRCUIT
101
103
103
STAGE 5
105
106
107
108
109
3RD COMPR. - CIRCUIT #3
UNIT
CIRCUIT #1
104
2ND COMPR. - CIRCUIT #2
STAGE 6
(SEE NOTE 3)
TB3
UNIT
CIRCUIT #2
110
111
112
LABEL DWG. 330423201 REV.0D
IMM ACZ/AGZ-4
ACZ / AGZ-BM
51
Dimensional Data
Figure 26, Dimensions: ACZ 030B - 080B
AGZ 026BM – 070BM
ISOLATOR LOCATIONS ON BOTTOM OF RAIL
67.8 (1721)
COMPRESSOR COMPRESSOR
CIRCUIT #1
CIRCUIT #2
13.3 (338)
13.3 (338)
REFRIGERANT CONNECTIONS
SUCTION
LINE #2
SUCTION
LINE #1
HOT GAS
BYPASS #1
HOT GAS
BYPASS #2
LIQUID
LINE #1
25.0
(636)
LIQUID
LINE #2
2.0
(51)
8.9 (226)
51.2 (1301)
CONTROL
PANEL
CONTROL
PANEL
POWER
ENTRY
POINT
0.875
KNOCK OUT
FIELD CONTROL
CONNECTION
100.4
(2550)
SUCTION
CONN.
Y
43.8
(1111)
25.8
(656)
16.7
424)
19.9
(506)
HOT GAS
CONN.
LIQUID
CONN.
19.9
(507)
25.1
(637)
9.1
(231)
Z
14.3 (364)
6.4 (162)
X
DWG. #3305196-R03
88.0 (2335)
94.4 (2397)
NOTES:
1.
Hail and wind guards add 20 inches to the width of each side.
2.
Be sure that the expansion valves’ sensing bulb and capillary are attached to the correct suction line.
52
ACZ-B
Unit Size
AGZ-BM
Unit Size
Liquid
Conn.
Suction
Conn.
030B
035B
040B
045B
050B
055B
060B
065B
070B
080B
026BM
030BM
035BM
040BM
045BM
050BM
055BM
060BM
065BM
070BM
(2) 1 3/8
(2) 1 3/8
(2) 1 3/8
(2) 1 3/8
(2) 1 3/8
(2) 1 3/8
(2) 1 3/8
(2) 1 3/8
(2) 1 3/8
(2) 1 3/8
(2) 2 1/8
(2) 2 1/8
(2) 2 1/8
(2) 2 1/8
(2) 2 1/8
(2) 2 5/8
(2) 2 5/8
(2) 2 5/8
(2) 2 5/8
(2) 2 5/8
Center of Gravity in. (mm)
X
Y
Z
36 (914)
36 (914)
36 (914)
36 (914)
36 (914)
36 (914)
35 (889)
35 (889)
35 (889)
36 (914)
ACZ / AGZ-BM
42 (1067)
42 (1067)
42 (1067)
41 (1041)
41 (1041)
42 (1067)
42 (1067)
42 (1067)
43 (1092)
44 (1118)
42 (1067)
42 (1067)
42 (1067)
41 (1041)
41 (1041)
42 (1067)
43 (1092)
43 (1092)
45 (1143)
46 (1168)
Weights lbs. (kg)
Shipping
Operating
3550 (1610)
3550 (1610)
3550 (1610)
3550 (1610)
3590 (1628)
3730 (1692)
3780 (1715)
3820 (1733)
3970 (1801)
4080 (1851)
3600 (1633)
3600 (1633)
3600 (1633)
3610 (1637)
3650 (1656)
3800 (1724)
3850 (1746)
4040 (1833)
4070 (1846)
4180 (1896)
IMM ACZ/AGZ-4
Figure 27, Dimensions: ACZ 090B - 110B
AGZ 075BM – 090BM
ISOLATOR LOCATIONS ON BOTTOM OF RAIL
110.1 (2797)
12.4
(315)
COMPRESSORS CIRC #2
12.4 (315)
REFRIGERANT CONNECTIONS
2.0 (51)
SUCTION
LINE #2
53.7
(1365)
SUCTION
LINE #1
HOT GAS
BYPASS #2
47.9
(1218)
40.0
(1017)
34.3
(870)
2.0 (51)
51.3 (1304)
HOT GAS
BYPASS #1
LIQUID
LINE #2
LIQUID
LINE #1
COMPRESSORS CIRC #1
CONTROL
PANEL
POWER
ENTRY
POINT
0.875
KNOCK OUTS
CONTROL
PANEL
FIELD CONTROL
CONNECTION
100.4
(2550)
Y
28.5
(724)
6.4
(162)
28.5
(724)
Z
88.0 (2235)
134.7 (3421)
14.4 (364)
X
Dwg. #3305025-R3
NOTES:
1.
Hail and wind guards add 20 inches to the width of each side.
2.
Be sure that the expansion valves’ sensing bulb and capillary are attached to the correct suction line.
IMM ACZ/AGZ-4
ACZ-B
Unit
Size
AGZ-BM
Unit
Size
Liquid
Conn.
Suction
Conn.
090B
100B
110B
075BM
085BM
090BM
(2) 1 3/8
(2) 1 3/8
(2) 1 3/8
(2) 3 1/8
(2) 3 1/8
(2) 3 1/8
Center of Gravity Inches (mm)
X
Y
Z
44 (1118)
43 (1092)
44 (1118)
46 (1168)
44 (1118)
41 (1041)
58 (1473)
58 (1473)
57 (1448)
ACZ / AGZ-BM
Weights Lbs. (kg)
Shipping
Operating
Weight
Weight
5510 (2499)
5630 (2554)
5670 (2572)
5790 (2626)
5830 (5830)
5950 (2699)
53
Figure 28, Dimensions: ACZ 120B - 155B
AGZ 100BM – 130BM
ISOLATOR LOCATIONS ON BOTTOM OF RAIL
67.8 (1721)
67.8 (1721)
12.4
COMPRESSORS CIRC #2 (315)
25.2
(640)
REFRIGERANT CONNECTIONS
2.0
(51)
53.73
(1364.7)
48.00
(1319.2)
39.95
(1014.7)
34.22
(869.2)
SUCTION
LINE #2
SUCTION
LINE #1
HOT GAS
BYPASS #2
HOT GAS
BYPASS #1
2.0
(51)
LIQUID
LINE #2
COMPRESSORS CIRC #1
82.4 (2093)
LIQUID
LINE #1
CONTROL
PANEL
CONTROL
PANEL
FIELD CONTROL
CONNECTION
17.6
(447)
23.9
(114)
POWER
ENTRY
POINT
0.875
KNOCK OUTS
100.4
(2550)
Y
9.0
(229)
43.8
(1111)
6.4(1624)
23.9
(114)
Z
X
88.0 (2235)
14.4 (365)
DWG. #3305026
173.1 (4396)
NOTES:
1.
Hail and wind guards add 20 inches to the width of each side.
2.
Be sure that the expansion valves’ sensing bulb and capillary are attached to the correct suction line.
54
ACZ-B
Unit
Size
AGZ-BM
Unit
Size
Liquid
Conn.
Suction
Conn.
120B
100BM
(2) 1 3/8
130B
110BM
(2) 1 3/8
140B
120BM
155B
130BM
Center of Gravity Inches (mm)
Weights Lbs. (kg)
Shipping
Operating
Weight
Weight
X
Y
Z
(2) 3 1/8
43 (1092)
46 (1168)
75 (1905)
6820 (3094)
6970 (3162)
(2) 3 1/8
44 (1118)
46 (1168)
73 (1854)
7080 (3211)
7230 (3280)
(2) 1 3/8
(2) 3 1/8
43 (1092)
63 (1600)
73 (1854)
7360 (3338)
7480 (3393)
(2) 1 3/8
(2) 3 1/8
44 (1118)
40 (1016)
71 (1803)
7640 (3466)
7760 (3520)
ACZ / AGZ-BM
IMM ACZ/AGZ-4
Remote Evaporators
Figure 29, Remote Evaporators, AGZ 026BM – 130BM
8.3
(211)
=
=
Suction
Circuit #2
Suction
Circuit #1
.85
(22)
W1
Inlet
32.9
(838)
Liquid
Circuit #1
1.9
(49)
M10x25
.67 (17)
11.4 (290)
13.5 (342)
AGZ
Model
026
030
035
040
045
050
055
060
065
070
.87 (22)
1.9 (49)
Liquid Line
Conn. Brazed, in
1.375
1.375
1.375
1.375
1.375
1.375
1.375
1.375
1.375
1.375
.87 (22)
1.9 (49)
A
Suction Line Conn.
Brazed, in (S).
2.125
2.125
2.125
2.125
2.125
2.125
2.125
2.625
2.625
2.625
W2
Outlet
Liquid
Circuit #2
Temp Sensor
Temp. Sensor
NPT, in. (TS)
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
Victaulic Water
Conn. In. (W)
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
Dimension
“A” in. (mm)
8.3 (210)
8.3 (210)
9.2 (233)
10.5 (267)
11.8 (300)
13.1 (336)
15.0 (380)
16.7 (425)
19.0 (481)
19.0 (481)
E
OUTLET
1/2” NPTF
CONNECTION
TEMP SENSOR
1/2” NPTF
INLET
B
1/4" NPTF (QTY 2)
A
C
D
VENT & DRAIN
1/2" NPTF
CIRCUIT 2
SUCTION
OUT
CIRCUIT 1
SUCTION
IN
F
L
CIRCUIT 1
LIQUID
H
K
I
G
.59" DIA. HOLES
(QTY. 4)
J
330488001
AGZ
Model
075
085
090
100
110
120
130
A
B
C
D
E
F
G
H
I
J
K
L
6.6
6.6
6.6
6.4
6.4
6.8
6.8
3.9
3.9
3.9
3.9
3.9
4.0
4.0
52.2
52.2
52.2
85.2
85.2
84.0
84.0
61.9
61.9
61.9
94.6
94.6
95.5
95.5
16.0
16.0
16.0
15.3
15.3
16.5
16.5
13.5
13.5
13.5
12.8
12.8
14.0
14.0
9.7
9.7
9.7
11.0
11.0
11.9
11.9
9.5
9.5
9.5
10.2
10.2
10.2
10.2
10.2
10.2
10.2
12.6
12.6
12.6
12.6
11.4
11.4
11.4
13.8
13.8
13.8
13.8
42.2
42.2
42.2
72.1
72.1
72.1
72.1
17.7
17.7
17.7
17.8
17.8
18.4
18.4
W
(Water)
(2) 5.0
(2) 5.0
(2) 5.0
(2) 5.0
(2) 5.0
(2) 8.0
(2) 8.0
S
(Suction)
(2) 3.125
(2) 3.125
(2) 3.125
(2) 3.125
(2) 3.125
(2) 3.125
(2) 3.125
L
(Liquid)
(2) 1.375
(2) 1.375
(2) 1.375
(2) 1.375
(2) 1.375
(2) 1.375
(2) 1.375
NOTE: Water connections are victaulic sized in inches. Refrigerant connections are IDS sized in inches.
IMM ACZ/AGZ-4
ACZ / AGZ-BM
55
Optional Features
Any of the following options can be included on a unit:
Controls
Hot Gas Bypass
Hot gas bypass permits unit operation down to 10% of full load capacity. This option includes a
factory-mounted hot gas bypass valve, solenoid valve, and manual shutoff valve for each circuit.
Head Pressure Control
Fan VFD low ambient control allows unit operation down to 0°F (-18°C). (Not available on 380
volt, 60 Hertz units.)
Water Flow Switch (AGZ-BM only)
(P/N 017503300) A water flow switch is available for field installation in the chilled water piping to
avoid evaporator freeze-up under low or no flow conditions. Terminals are provided in the unit
control center for field hook-up of the water flow switch. If this option is not ordered with the unit,
then a field supplied water flow switch must be installed.
Alarm Bell
Field-installed and wired to the control panel to provide remote indication of unit alarm condition.
See Field Wiring Diagram for connection locations.
BAS Interface (Protocol Selectability™ Feature)
Connection to Chiller
Connection to the chiller for all Building Automation System (BAS) protocols will be at the unit
controller. An interface card, depending on the protocol being used, can be factory-installed in the
unit controller (or it can be field-installed).
Protocols Supported
Table 37, Standard Protocol Data
Protocol
Physical Layer
Data Rate
Controller
®
BACnet /IP or
BACnet/Ethernet
2
Ethernet 10 Base-T
10 Megabits/sec
pCO Unit Controller
BACnet MSTP
RS-485
(TBD)
pCO Unit Controller
LONWORKS®
FTT-10A
78kbits/sec
pCO Unit Controller
Modbus RTU?
RS-485or RS-232
(TBD)
pCO Unit Controller
2
2
Other
Reference ED 15057:
BACnet PICS
Reference ED 15057:
BACnet PICS
LONMARK® Chiller
Functional Profile
2
Note: For additional information on the protocol data available through the BACnet or
LONWORKS communications modules reference ED 15062, MicroTech II Chiller Unit Controller
Protocol Information.
Modbus – When selected, the ident number and baud rate can also be changed to suit the application.
LONWORKS – When selected, the ident number and baud rate setpoints are not available. Baud rate
is locked at 4800.
BACnet – When selected, the ident number and baud rate setpoints are not available. Baud rate is
locked at 19200.
56
ACZ / AGZ-BM
IMM ACZ/AGZ-4
The interface kits on the MicroTech II™ controller are as follows:
• BACnet Kit P/N 350147404: BACnet/IP, BACnet MS/TP, or BACnet Ethernet
• LONWORKS Kit P/N 350147401: LonTalk (FTT-10A)
• Modbus RTU
The following functions are available through the BAS where possible. Exact capabilities can vary
depending on the protocol in use.
•
Enable/Disable chiller operation by setting the Unit Enable setpoint.
•
Select the operating mode by setting the Unit Mode setpoint.
•
Set the Cool LWT and Ice LWT setpoints.
•
Read all digital and analog I/O values.
•
Read Enable status of chiller.
•
Read current operating mode and status (state) of chiller.
• Send a description of each alarm when it occurs.
Reference documents ED 15057, ED 15062 and ED 15063 can be obtained from the local McQuay
sales office, or they can also be found on www.mcquay.com under Product Information > (chiller
type) > Control Integration.
®™ The following are trademarks or registered trademarks of their respective companies: BACnet
from the American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc., LonTalk,
LONMARK and LONWORKS from Echelon Corporation, and Modbus from Schneider Electric.
Unit
Vibration Isolators
Spring or neoprene-in-shear vibration isolators are available for field installation to reduce vibration
transmission through the unit base. See page 12 for detailed information on their installation.
Protective Base Guards
Optional factory installed vinyl-coated welded wire base guards provide all-around lower unit
protection on ground level installations. Coil guards are standard.
Copper Fin Condenser Coils
Copper fin condenser coils are available as an option on all models.
Black Fin Coils
Aluminum fin stock precoated with a phenolic coating with 1000 hour salt spray resistance (ASTM
B117-90).
Coated Fins
Copper or aluminum fins coated with ElectroFin® baked epoxy protective coating with 3000+ hour
salt spray resistance (ASTM B117-90).
Evaporator Insulation (AGZ-BM only)
Double insulation thickness (total of 1 ½ inch) for high humidity areas or low fluid temperatures.
Sound Reduction
Acoustical blankets are factory-installed on each compressor.
Hail and Wind Guards
A field-mounted option shipped as a kit including panels, fasteners, and instructions. See page 26 for
further information.
IMM ACZ/AGZ-4
ACZ / AGZ-BM
57
Refrigerant Specialties Kit
Required on AGZ-BM Remote Evaporator units consisting of thermal expansion valve, solenoid
valve, sight glass and filter-drier (sealed on Models 026 to 070, replaceable core on Models 075 to
130).
Electrical
Multi-Point Electrical Connection
Provides a power connection to each of the unit’s two electrical circuits.
Disconnect Switch with Through-the-Door Handle
A factory or field-installed option for service use, nonfused disconnect switch (mounted inside the
power section of the control box) with a through-the-door handle is available with single and multipoint power supply.
Phase Loss/Voltage Protection
Phase loss with under/over voltage protection and multiple LED indication of fault type is available
as a factory-installed option to guard against compressor motor burnout.
Convenience Outlet
10.0 amp, 115 volt outlet located in control panel to provide power for servicing unit.
Ground Fault Protection
Protects equipment from damage from line-to-ground fault currents less than those required for
conductor protection.
High Short Circuit Current Protection
Provides control panel protection against short circuit currents per following table:
Voltage
208
240
460
600
Current (kA)
120
100
65
25
High Ambient Control Panel
Consists of exhaust fan with rain hood, two inlet screens with filters, necessary controls and wiring
to allow operation to 125°F. The option can be factory or field-installed as a kit. Must be used for:
• Ambient temperatures above 105°F (40°C) with fan VFD (low ambient option)
• Ambient temperatures above 115°F (46°C) with standard FanTrol control.
58
ACZ / AGZ-BM
IMM ACZ/AGZ-4
Start-up
Pre Start-up
The unit must be inspected to see that no components became loose or damaged during shipping or
installation.
Start-Up
There should be adequate building load (at least 50 percent of the unit full load capacity) to properly
check the operation of the unit’s refrigerant circuits.
Record all operating parameters required by the “Compressorized Equipment Warranty Form”.
Return this information within 10 working days to McQuay International as instructed on the form to
register the start-up date with the McQuay Warranty Department.
1. Verify chilled water or air-flow.
2. Verify that the remote start / stop or time clock has requested the chiller to start.
3. Set the thermostat setpoint to required temperature. For AGZ-AM units, the system water
temperature must be greater than the total of the leaving water temperature setpoint plus 1/2 the
control band before the MicroTech II controller will stage on cooling. Set the Evap Delta T and
the Start Delta T as a starting point.
4. Put both pumpdown switches (PS1 and PS2) to the ON position.
5. Put system switch (S1) to ON position.
Switch
PS1, PS2,
Pumpdown
Switches
S1,
System Switch
Switch Position
ON
Circuits will operate in the
normal automatic mode
Unit will operate in the
normal automatic mode
OFF
Circuit will go through the
normal pumpdown cycle and
shut off.
Unit will shut off immediately
without pumping down
(emergency stop)
6. There can be a delay of 2 minutes after closing S1. The time delay is due to the compressor
inherent motor protection or the Stage Up Timer counting. This should only occur on initial
start-up or when power to the chiller has been turned off and back on. More than one
compressor will not start at the same time.
7. After the chiller has been operating for a period of time and has become stable, check the
following:
ƒ Compressor oil level. (Some scroll compressors do not have oil sight glasses)
ƒ Refrigerant sight glass for flashing.
ƒ Rotation of condenser fans.
8. Complete the “Compressorized Equipment Warranty Form”.
IMM ACZ/AGZ-4
ACZ / AGZ-BM
59
Shutdown
Temporary
1. Put both circuit switches to the OFF position (Pumpdown and Stop).
2. After compressors have stopped, put System Switch (S1) to OFF (emergency stop).
3. Turn off chilled water pump or air handler if applicable. Chilled water pump to operate while
compressors are pumping down.
To start the chiller after a temporary shutdown, follow the start-up instructions.
Extended
1. Front seat both condenser liquid line service valves.
2. Put both circuit switches to the OFF position (Pumpdown and Stop position.)
3. After the compressors have stopped, put System Switch (S1) to the OFF position (emergency
stop).
4. Front seat both refrigerant circuit discharge valves (if applicable).
5. If electrical power is on to unit, the compressor crankcase heaters will keep the liquid refrigerant
out of the compressor oil. This will minimize start-up time when putting the unit back into
service. The evaporator heater will be able to function.
6. If electrical power is off, tag all opened electrical disconnect switches to warn against start-up
before the refrigerant valves are in the correct operating position. When starting the unit,
electrical power must be on for 24 hours before starting the chiller.
To start the chiller after an extended shutdown, follow the prestart-up and start-up instructions.
Water Piping Checkout
1. Check the pump operation and vent all air from the system.
2. Circulate evaporator water checking for proper system pressure and pressure drop across the
chiller barrel. Compare the pressure drop to the evaporator water pressure drop curve.
3. Clean all water strainers before placing the unit into service.
Refrigerant Piping Checkout
1. Check all exposed brazed joints on the unit, as well as any field-installed piping, for evidence of
leaks. Joints can have been damaged during shipping or when the unit was installed.
2. Check that all refrigerant valves are either opened or closed as required for proper operation of
the unit.
3. A thorough leak test must be done using an approved electronic leak detector. Check all valve
stem packing for leaks. Replace all refrigerant valve caps and tighten.
4. Check all refrigerant lines to see that they will not vibrate against each other or against other unit
components and are properly supported.
5. Check all flare connections and all refrigerant threaded connectors.
6. Look for any signs of refrigerant leaks around the condenser coils and for damage during
shipping or installation.
7. Leak detector is applied externally to refrigerant joints at the factory. Do not confuse this residue
with an oil leak.
8. Connect refrigerant service gauges to each refrigerant circuit before starting unit.
60
ACZ / AGZ-BM
IMM ACZ/AGZ-4
Electrical Check Out
CAUTION
Electrical power must be applied to the compressor crankcase heaters
24 hours before starting unit to drive off refrigerant from the
oil or compressor damage can occur.
1. Open all electrical disconnects and check all power wiring connections. Start at the power block
and check all connections through all components to and including the compressor terminals.
These should be checked again after 3 months of operation and at least annually thereafter.
2. Check all control wiring by pulling on the wire at the spade connections and tighten all screw
connections. Check plug-in relays for proper seating and that retaining clips are installed.
3. Put System Switch (S1) to the Emergency Stop position.
4. Put both circuit #1 & #2 switches to the Pumpdown and Stop position.
5. Apply power to the unit. The panel Alarm Light will stay on until S1 is closed. Ignore the
Alarm Light for the checkout period. If you have the optional Alarm Bell, you can disconnect it.
6. Check at the power block or disconnect for the proper voltage and for the proper voltage
between phases. Check power for proper phasing using a phase sequence meter before starting
unit.
7. Check for 120Vac at the control transformer and at TB-2 terminal #1 and the neutral block (NB).
8. Check between TB-2 terminal #7 and NB for 120Vac supply for transformer #2.
9. Check between TB-2 terminal #2 and NB for 120Vac control voltage. This supplies the
compressor crank case heaters.
10. Check between TB-3 terminal #17 and #27 for 24Vac control voltage.
Operation
Hot Gas Bypass (Optional)
This option allows the system to operate at lower loads without excessive on/off compressor cycling.
The hot gas bypass option is required to be on both refrigerant circuits because of the lead / lag
feature of the controller.
This option allows passage of discharge gas into the evaporator inlet (between the TX valve and the
evaporator) which generates a false load to supplement the actual chilled water or air handler load.
Note: The hot gas bypass valve cannot generate a 100% false load.
The valve that is supplied can provide a load of approximately 10 tons. The system load added to the
ten tons of the hot gas bypass valve has to exceed the compressor capacity for stage 1 compressors to
produce stable system operation. This requires 3-6 tons of system load.
The MicroTech II controls solenoid valves in the hot gas bypass lines that are energized whenever
their circuit is operating with only one compressor running. The hot gas valve is regulated by the
evaporator pressure and the remote adjustable bulb. The pressure regulating valve is factory set to
begin opening at 58 psig (32°F for R-22).
WARNING
The hot gas line can become hot enough to cause injury.
Be careful during valve checkout.
IMM ACZ/AGZ-4
ACZ / AGZ-BM
61
VFD Low Ambient Control (Optional)
The optional VFD fan control is used for unit operation below 35°F (2°C) down to a minimum of
0°F (-17°C). The control looks at the saturated discharge temperature and varies the fan speed to
hold the temperature (pressure) at the “target” temperature. This temperature is established as an
input to a setpoint screen labeled “Sat Condenser Temp Target”.
Filter-Driers (AGZ-BM)
A full flow filter-drier (AGZ 026 – 070) or a replaceable core type filter-drier (AGZ 075 – 130) for
each refrigerant circuit is shipped loose for field mounting. The core assembly of the replaceable
core drier consists of a filter core held tightly in the shell to allow full flow without bypass.
Pressure drop across the filter-drier at full load conditions must not exceed 10 psig at full load. See
Table 38 for pressure drop at other load points. Replace the filter-drier if the pressure drop exceeds
maximum.
WARNING
Pump out refrigerant before removing end flange for replacement of core(s).
Lowering refrigerant pressure will help prevent accidental blow-off of cover
causing possible bodily injury. EPA recovery regulations apply to this procedure.
A condenser liquid line service valve is provided for isolating the charge in the condenser, but also
serves as the point from which the liquid line can be pumped out. With the line free of refrigerant,
the filter-drier core(s) can be easily replaced.
System Adjustment
To maintain peak performance at full load operation, the system superheat and liquid subcooling can
require adjustment. Read the following subsections closely to determine if adjustment is required.
Liquid Line Sight Glass and Moisture Indicator
The color of the moisture indicator is an indication of the dryness of the system and is extremely
important when the system has been serviced. Immediately after the system has been opened for
service, the element can indicate a wet condition. It is recommended that the equipment operate for
about 12 hours to allow the system to reach equilibrium before deciding if the system requires a
change of drier cores.
Bubbles in the sight glass at constant full load indicates a shortage of refrigerant, a plugged filterdrier, or a restriction in the liquid line. However, it is not unusual to see bubbles in the sight glass
during changing load conditions.
Refrigerant Charging
Liquid line subcooling at the liquid shut-off valve should be between 15 and 20 degrees F at full
load. If the unit is at steady full load operation and bubbles are visible in the sight glass, then check
liquid subcooling.
Thermostatic Expansion Valve
The expansion valve performs one specific function. It keeps the evaporator supplied with the
proper amount of refrigerant to satisfy the load conditions.
The sensing bulb of the expansion valve is installed in the closest straight run of suction line from
the evaporator. The bulb is held on by clamps around the suction line and is insulated to reduce the
effect of surrounding ambient temperatures. In case the bulb must be removed, simply slit the
insulation on each side of the bulb, remove the clamps and then remove the capillary tubing that runs
along the suction line from the valve.
The power element is removable from the valve body without removing the valve from the line.
62
ACZ / AGZ-BM
IMM ACZ/AGZ-4
NOTE: Before adjusting superheat, check that unit charge is correct and liquid line sight
glass is full with no bubbles and that the circuit is operating under stable, full load
conditions.
The suction superheat for the suction leaving the evaporator is set at the factory for 8 to 12 degrees F
at full load. To have full rated unit performance, the superheat must be about 8 degrees F at 95°F
outdoor ambient temperature.
Crankcase Heaters
The scroll compressors are equipped with externally mounted band heaters located at the oil sump
level. The function of the heater is to keep the temperature in the crankcase high enough to prevent
refrigerant from migrating to the crankcase and condensing in the oil during off-cycle.
NOTE: Power must be supplied to the heaters 24 hours before starting the compressors.
Evaporator
Models AGZ 026 through 070
The evaporator is a compact, high efficiency, dual circuit, brazed plate-to-plate type heat exchanger
consisting of parallel stainless steel plates.
The evaporator is protected with an electric resistance heater and insulated with 3/4" (19mm) thick
closed-cell polyurethane insulation. This provides freeze protection down to -20°F (-29°C) ambient
air temperature.
The water side working pressure is 363 psig (2503 kPa). Evaporators are designed and constructed
according to, and listed by, Underwriters Laboratories (UL).
Models AGZ 075 through 130
The evaporator is direct expansion, shell-and-tube type with water flowing in the baffled shell side
and refrigerant flowing through the tubes. Two independent refrigerant circuits within the evaporator
serve the unit's dual refrigerant circuits.
The evaporator has a carbon steel shell and seamless high efficiency copper tubes, roller expanded
into a carbon steel tube sheet.
3/8" (10mm) vent and drain plugs are provided on the top and bottom of the shell.
The evaporator is wrapped with an electric resistance heater cable and insulated with 3/4" (19mm)
thick vinyl nitrate polymer sheet insulation, protecting against water freeze-up at ambient air
temperatures to -20°F (-29°C). An ambient air thermostat controls the heater cable. The fitted and
glued-in-place insulation has a K factor of 0.28 Btu in/hr ft2 at 75°F.
The refrigerant (tube) side maximum working pressure is 300 psig (2068 kPa). The water-side
working pressure is 152 psig (1048 kPa). Each evaporator is designed, constructed, inspected, and
stamped according to the requirements of the ASME Boiler and Pressure Vessel Code. Double
thickness insulation is available as an option.
IMM ACZ/AGZ-4
ACZ / AGZ-BM
63
Unit Maintenance
General
On initial start-up and periodically during operation, it will be necessary to perform certain routine
service checks. Among these are checking the liquid line sight glasses, taking condensing and
suction pressure readings, and checking to see that the unit has normal superheat and subcooling
readings. A recommended maintenance schedule is located at the end of this section.
Compressor Maintenance
The scroll compressors are fully hermetic and require no maintenance.
Lubrication
No routine lubrication is required on AGZ units. The fan motor bearings are permanently lubricated
and no further lubrication is required. Excessive fan motor bearing noise is an indication of a
potential bearing failure.
Compressor oil should be standard refrigeration mineral oil such as Suniso 3GS.
Electrical Terminals
DANGER
Electric shock hazard. Disconnect all power before continuing with following
service.
Condensers
The condensers are air-cooled and constructed of 3/8" (9.5mm) O.D. internally finned copper tubes,
bonded in a staggered pattern into louvered aluminum fins. Maintenance consists of routine removal
of dirt and debris from the outside surface of the fins. McQuay recommends the use of foaming coil
cleaners available at most air conditioning supply outlets. Use caution when applying such cleaners
as they can contain potentially harmful chemicals. Care should be taken not to damage the fins
during cleaning. The coils should be thoroughly rinsed to remove any cleaner residue.
If the service technician determines that the refrigerant circuit contains noncondensables, recovery
can be required, strictly following Clean Air Act regulations governing refrigerant discharge to the
atmosphere. The Schrader purge valves are located on the vertical coil headers on both sides of the
unit, at the end opposite from the control box. Decorative panels cover the coil headers and must be
removed for servicing. Recover with the unit off, after a shutdown of 15 minutes or longer, to allow
air to collect at the top of the coil. Restart and run the unit for a brief period. If necessary, shut unit
off and repeat the procedure. Follow accepted environmentally sound practices when removing
refrigerant from the unit.
Refrigerant Sight Glass
The refrigerant sight glasses should be observed periodically. (A weekly observation should be
adequate.) A clear glass of liquid indicates that there is normal subcooled refrigerant in the system.
Bubbling refrigerant in the sight glass, during stable run conditions, indicates that the system can be
short of refrigerant charge. Refrigerant gas flashing in the sight glass could also indicate an
excessive pressure drop in the liquid line, possibly due to a clogged filter-drier or a restriction
elsewhere in the liquid line. See Table 38 for maximum allowable pressure drops. If subcooling is
low, add charge to clear the sight glass. If subcooling is normal (15 to 20 degrees F) and flashing is
visible in the sight glass, check the pressure drop across the filter-drier. Subcooling should be
checked at full load with at least 70°F (21.1°C) outdoor air temperature, stable conditions, and all
fans running.
64
ACZ / AGZ-BM
IMM ACZ/AGZ-4
An element inside the sight glass indicates the moisture condition corresponding to a given element
color. If the sight glass does not indicate a dry condition after about 12 hours of operation, the
circuit should be pumped down and the filter-drier changed; or verify system condition by
performing an acid test on the compressor oil.
Preventive Maintenance Schedule
OPERATION
WEEKLY
General
Complete unit log and review (Note 3)
Visually inspect unit for loose or damaged components
Inspect thermal insulation for integrity
Clean and paint as required
ANNUAL
(Note 2)
X
X
X
X
Electrical
Check terminals for tightness, tighten as necessary
Clean control panel interior
Visually inspect components for signs of overheating
Verify compressor heater operation
Test and calibrate equipment protection and operating controls
Megger compressor motor *
Refrigeration
Leak test
Check sight glasses for clear flow
Check filter-drier pressure drop (see manual for spec)
Perform compressor vibration test
Acid test oil sample
MONTHLY
(Note 1)
X
X
X
X
X
X
X
X
X
Condenser (air-cooled)
Clean condenser coils (Note 4)
Check fan blades for tightness on shaft (Note 5)
Check fans for loose rivets and cracks
Check coil fins for damage
X
X
X
X
X
X
Notes:
1.
2.
3.
4.
5.
Monthly operations include all weekly operations.
Annual (or spring start-up) operations includes all weekly and monthly operations.
Log readings can be taken daily for a higher level of unit observation.
Coil cleaning can be required more frequently in areas with a high level of airborne particles.
Be sure fan motors are electrically locked out.
*
Never Megger motors while they are in a vacuum.
IMM ACZ/AGZ-4
ACZ / AGZ-BM
65
Service
CAUTION
Service on this equipment is to be performed by qualified refrigeration personnel
familiar with equipment operation, maintenance, correct servicing procedures, and
the safety hazards inherent in this work. Causes for repeated tripping of
equipment protection controls must be investigated and corrected.
Disconnect all power before doing any service inside the unit.
Anyone servicing this equipment shall comply with the requirements set forth by
the EPA in regards to refrigerant reclamation and venting.
Filter-Driers
A replacement of the filter-drier is recommended any time excessive pressure drop is read across the
filter-drier and/or when bubbles occur in the sight glass with normal subcooling. The maximum
recommended pressure drop across the filter-drier is as follows:
Table 38, Filter-Drier Pressure Drop
PERCENT CIRCUIT
LOADING (%)
100%
75%
50%
25%
MAXIMUM RECOMMENDED PRESSURE
DROP ACROSS FILTER-DRIER PSIG (KPA)
10 (69)
8 (55.2)
5 (34.5)
4 (27.6)
The filter-drier should also be changed if the moisture indicating liquid line sight glass shows excess
moisture in the system.
During the first few months of operation, filter-drier replacement can be necessary if the pressure
drop across the filter-drier exceeds the values listed in the paragraph above. Any residual particles
from the condenser tubing, compressor and miscellaneous components are swept by the refrigerant
into the liquid line and are caught by the filter-drier.
Liquid Line Solenoid Valve
The liquid line solenoid valves that shut off refrigerant flow in the event of a power failure do not
normally require any maintenance. The solenoids can, however, require replacement of the solenoid
coil or of the entire valve assembly.
The solenoid coil can be checked to see that the stem is magnetized when energized by touching a
screwdriver to the top of the stem. If there is no magnetization, either the coil is bad or there is no
power to the coil.
The solenoid coil can be removed from the valve body without opening the refrigerant piping after
pumpdown. Shut off and lock-out the unit power.
The coil can then be removed from the valve body by simply removing a nut or snap-ring located at
the top of the coil. The coil can then be slipped off its mounting stud for replacement.
To replace the entire solenoid valve follow the steps involved when changing a filter-drier.
66
ACZ / AGZ-BM
IMM ACZ/AGZ-4
Remote Evaporator (AGZ-BM Only)
The evaporator is the direct expansion, shell-and-tube type with refrigerant flowing through the tubes
and water flowing through the shell over the tubes. The tubes are internally finned to provide
extended surface as well as turbulent flow of refrigeration through the tubes. Models AGZ 070BM
or smaller have a stainless steel brazed-plate type evaporator. Other than cleaning and testing, no
service work should be required on the evaporator.
Refrigerant Charging
Units are shipped with a holding charge of refrigerant and the system must be charged at the job site.
Follow these recommendations when field charging. Refer to the unit operating charge found in the
Physical Data Tables.
Unit charging can be done at any steady load condition (preferably at 75 to 100% load), and at any
outdoor temperature (preferably higher than 70°F (21.1°C). Unit must be allowed to run 5 minutes
or longer so that the condenser fan staging is stabilized at normal operating discharge pressure. For
best results charge with two or more condenser fans operating on each refrigerant circuit.
The ACZ/AGZ units have a condenser coil design with approximately 15% of the coil tubes located
in a subcooler section of the coil. This results in liquid cooling to within 5°F (3°C) of the outdoor air
temperature when all condenser fans are operating. This is equal to about 15°F-20°F (8.3°C-11.1°C)
subcooling below the saturated condensing temperature when the pressure is read at the liquid valve
between the condenser coil and the liquid line filter-drier. Once the subcooler is filled, extra charge
will not lower the liquid temperature and does not help system capacity or efficiency.
One of the following three scenarios will be experienced with an undercharged unit:
1. If the unit is slightly undercharged, the unit will show bubbles in the sight glass. Recharge the
unit as described in the charging procedure below.
2. .If the unit is moderately undercharged, it will normally trip on freeze protection. Recharge the
unit as described in the charging procedure below. However, freezestat trips can also be an
indication of low flow or poor heat transfer in the system evaporator.
3. If the unit is severely undercharged, the unit will trip due to lack of liquid flow to the expansion
valve. In this case, either remove the remaining charge by means of a proper reclamation system
and recharge the unit with the proper amount of refrigerant as stamped on the unit nameplate, or
add refrigerant through the suction valve on the compressor. If the unit is severely undercharged,
the unit can nuisance trip during this charging procedure. If this happens, operate the unit at
minimum load, adding charge until the sight glass is clear. Once the unit has enough charge so
that it does not trip out, continue with step 2 of the charging procedure below.
Procedure to charge a moderately undercharged ACZ/AGZ unit:
1. If a unit is low on refrigerant, you must first determine the cause before attempting to recharge
the unit. Locate and repair any refrigerant leak. Evidence of oil is a good indicator of leakage,
however, oil can not be visible at all leaks. Liquid leak detector fluids work well to show
bubbles at medium sized leaks, but electronic leak detectors can be needed to locate small leaks.
2. Add the charge to the system through the suction shutoff valve or through the Schrader fitting on
the tube entering the evaporator between the compressor and the evaporator head.
3. The charge can be added at any load condition between 25-100% load per circuit but at least two
fans should be operating per refrigerant circuit if possible. The suction superheat should be in
the 8 to 12 degree F (4.4°C - 6.6°C) range.
4. Add sufficient charge to clear the liquid line sight glass and until all flashing stops in the sight
glass.
IMM ACZ/AGZ-4
ACZ / AGZ-BM
67
5. Check the unit subcooling value by reading the liquid line pressure and temperature at the liquid
line near the filter-drier. The subcooling values should be between 15 and 20 degrees F (8.3 and
11.1 degrees C).
6. With outdoor temperatures above 60°F (15.6°C) all condenser fans should be operating and the
liquid line temperature should be within 5°F-10°F (2.8°C-5.6°C) of the outdoor air temperature.
At 25-50% load the liquid line temperature should be within 5°F (2.8°C) of outdoor air
temperature with all fans on. At 75-100% load the liquid line temperature should be within 10°F
(5.6°C) of outdoor air temperature with all fans on.
7. Overcharging of refrigerant will raise the compressor discharge pressure due to filling of the
condenser tubes with excess refrigerant.
Warranty Statement
Limited Warranty
Consult your local McQuay Representative for warranty details. Refer to Form 933-43285Y. To find
your local McQuay Representative, go to www.mcquay.com.
68
ACZ / AGZ-BM
IMM ACZ/AGZ-4
ACZ/AGZ Troubleshooting Chart
PROBLEM
Compressor
Will Not Run
Compressor
Noisy Or
Vibrating
High Discharge
Pressure
Low Discharge
Pressure
High Suction
Pressure
Low Suction
Pressure
1.
2.
POSSIBLE CAUSES
Main Switch.
Fuse Blown. Circuit breakers open
3.
Thermal overloads tripped
4.
5.
Defective contactor or coil.
System Shutdown by equipment protection
devices
6.
7.
8.
9.
No cooling required
Liquid line solenoid will not open
Motor electrical trouble
Loose wiring
1.
2.
3.
Low or no refrigerant charge
Compressor running in reverse
Improper piping support on suction or
discharge
Worn compressor isolator bushing
Worn Compressor
Noncondensables in system
4.
5.
1.
2. System overcharged with refrigerant
3. Optional discharge shutoff valve partially
closed
4. FanTrol wiring not correct
5. Fan not running
6. Dirty condenser coil
7. Air recirculation
1. Refrigerant flood back
2. Wind blowing into coil at low ambient
3. Faulty condenser temperature regulation
4. Insufficient refrigerant in system
5. Low suction pressure
6.
Only one compressor operating
1.
2.
3.
4.
1.
2.
Excessive water temperature
Excessive load
Expansion valve overfeeding
Compressors running in reverse
Rapid load swings
Lack of refrigerant
3.
Clogged liquid line filter-drier
4.
5.
Expansion valve malfunctioning
Condensing temperature to low
6.
Compressor will not unload
7.
8.
Insufficient water flow
Evaporator head ring gasket slippage
9. Evaporator dirty
10. Rapid load swings
POSSIBLE CORRECTIVE STEPS
Close Switch.
Check electrical circuits and motor windings
for shorts or grounds. Investigate for
possible overloading. Replace fuse or reset
breakers after fault is corrected. Check for
loose or corroded connections.
3. Overloads are auto-reset Check unit closely
when unit comes back on line. Allow time for
auto-reset.
4. Repair or replace
5. Determine type and cause of shutdown and
correct it before resetting equipment
protection switch
6. None. Wait until unit class for cooling
7. Repair or replace solenoid coil. Check wiring
8. Check motor for opens, shorts, or burnout
9. Check all wire junctions. Tighten all terminal
screws
1. Repair and recharge
2. Check unit and compressor for correct
phasing
3. Relocate, add, or remove hangers
4. Replace
5. Replace
1. Extract the noncondensables with approved
procedures
2. Remove excess, check liquid subcooling
3. Open valve
1.
2.
4.
5.
6.
7.
1.
2.
3.
4.
5.
Check FanTrol wiring
Check electrical circuit, Check fan motor
Clean coil
Correct
Correct
Shield coil from direct wind
Check condenser control operation
Check for leaks. Repair and add charge
See corrective steps for Low Suction
Pressure
6. See corrective steps for Compressor Will Not
Stage Up
1. Check control settings
2. Reduce load or add additional equipment
3. Check remote bulb. Regulate superheat
4. Check for proper phasing
1. Stabilize load
2. Check for leaks, repair, add charge. Check
liquid sight glass
3. Check pressure drop across filter-drier.
Replace
4. Check and reset for proper superheat
5. Check means for regulating condenser
temperature
6. See corrective steps for Compressor Staging
Intervals Too Low
7. Adjust flow
8. Take pressure drop across vessel and
contact factory to obtain design pressure
drop for that vessel
9. Clean chemically
10. Stabilize load
Continued next page.
IMM ACZ/AGZ-4
ACZ / AGZ-BM
69
PROBLEM
Compressor
Will Not Stage
Up
Compressor
Staging
Intervals Too
Short
Compressor Oil
Level Too High
Or Too Low
Compressor
Loses Oil
Motor Overload
Relays Or
Circuit Breakers
Open
Compressor
Thermal
Protection
Switch Open
70
1.
2.
3.
1.
2.
3.
4.
1.
2.
3.
4.
5.
6.
POSSIBLE CAUSES
Defective capacity control
Faulty thermostat stage or broken wire
Stages not set for application
Thermostat control band not set properly
Erratic water thermostat
Insufficient water flow
Rapid load swings
Oil hang-up in piping
Low oil level
Loose fitting on oil line
Level too high
Insufficient water flow - Level too high
Excessive liquid in crankcase - Level too high
1.
2.
3.
1.
2.
3.
4.
1.
2.
3.
4.
5.
6.
7.
1.
2.
3.
4.
1.
2.
3.
4.
Short cycling
Lack of refrigerant
Excessive compression ring blow-by
Suction superheat too high
Crankcase heater burnout
Low voltage during high load conditions
Defective or grounded wiring in motor
Loose power wiring or burnt contactors
High condenser temperature
7.
1.
2.
3.
4.
1.
2.
3.
4.
5.
Power line fault causing unbalanced voltage
5.
1.
Operating beyond design conditions
1.
2.
3.
4.
5.
6.
Discharge valve partially shut
Blown compressor internal gasket
Voltage range or imbalance
High superheat
Compressor bearing failure
2.
3.
4.
5.
6.
ACZ / AGZ-BM
POSSIBLE CORRECTIVE STEPS
Replace
Replace
Reset thermostat setting for application
Set control band wider
Replace
Adjust flow
Stabilize load
Review refrigerant piping and correct
Check and add oil
Check and tighten system
Adjust thermal expansion valve
Adjust flow
Check crankcase heater. Reset expansion
valve for higher superheat. Check liquid line
solenoid valve operation.
Stabilize load or increase staging interval
Check for leaks and repair. Add refrigerant
Replace compressor
Adjust superheat
Replace crankcase heater
Check supply voltage for excessive line drop
Replace compressor motor
Check all connections and tighten
See corrective steps for High Discharge
Pressure
Check supply voltage. Notify power
company. Do not start until fault is corrected.
Add facilities so conditions are within
allowable limits
Open valve
Replace gasket
Check and correct
Adjust to correct superheat
Replace compressor
IMM ACZ/AGZ-4
IMM ACZ/AGZ-4
ACZ / AGZ-BM
71
72
ACZ / AGZ-BM
IMM ACZ/AGZ-4
This document contains the most current product information as of this printing. For the most up-todate product information, please go to www.mcquay.com.
(800) 432-1342 • www.mcquay.com
IMM ACZ/A