WebGate WebEye E104 User`s guide

WebEye E10/E104 Manual Ver 1.5
WebEye E10/E104 User’s Guide
* This manual is for WebEye firmware version 1.2.0. If your WebEye has the later version
of firmware, please download the last updated user’s guide from WebGate ’s homepage
(www.webgateinc.com)
System Requirements
n For WebEye
•
Network: 10 Base-T LAN
(Leased line, xDSL, Cable Modem, ISDN)
n For a PC to access WebEye
•
Processor: Pentium II and above
•
RAM: 64MB and more
•
OS: Windows 98/NT/2000
•
Screen Resolution: 1024 X 768 pixels and above
•
•
Network: 10 Base-T LAN or PSTN
Web Browser: MS Internet Explorer 5.0 and above
NS Navigator 4.7 and above
WebGate Inc.
FCC Compliance Statement
Caution : Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE : This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environmental. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the
interference at own expense.
Warning
This is a class ‘A’ product. In a domestic environment, this product may cause radio
interference in which case the user may be required to take adequate measures
2
WebEye E10/E104 User’s Guide
Important Notice
1. WebEye is for indoor use. Therefore note that the CCD (charged coupled device) inside the
product can be damaged permanently if the camera lens is exposed to direct sunlight. When
you place WebEye under the glaring light, we recommend using an iris lens. If your
application demands prolonged exposure to sunlight, you should consider to equip with a
sun visor.
2. WebEye is not weatherproof. Therefore you should be well aware of environmental
specifications that are included in the manual. In case of outdoor use, where it needs
additional weather criteria, you should equip weatherproof case to protect WebEye from
water, moisture, or temperature (higher or lower than specification). For WebEye cleaning,
gently wipe with clean dry cloth.
3. Be sure to use a DC adapter that is provided by Web Gate Inc. Connecting WebEye directly
to an AC current, may cause electric damages to WebEye.
4. Be caution in handling WebEye for physical shocks may harm the product.
5. WebEye E104 is made of aluminum. Therefore you can hurt human beings if you throw it
to them or hit on them. When installing WebEye, be sure it is attached tight and stable to
avoid any human injures. Be cautious to locate on safe places where children are
unreachable.
6. If WebEye does not operate properly, please contact the closest local WebGate distributor
for after sales service. In all cases, you are prohibited to disassemble the product. If so,
WebGate is not responsible for any malfunction nor service warranty.
7. Camera surveillance laws may differ for each country. Therefore, please contact the local
region first to avoid any surveillance law violations and to apply for authorized purposes
only.
3
WebEye E10/E104 User’s Guide
CONTENTS
I. Introduction.............................................................................................................................7
II. Product Description................................................................................................................ 8
1. WebEye E104 .................................................................................................................... 8
1) Contents .................................................................................................................... 8
2) Rear View and Descriptions ........................................................................................ 8
3) Descriptions on DB-15 port......................................................................................... 9
4) Description on LED of Ethernet Port ........................................................................... 9
5) Descriptions on DIP Switches ....................................................................................10
2. WebEye E10 .....................................................................................................................12
1) Contents ...................................................................................................................12
2) Rear View and Descriptions .......................................................................................12
3) Descriptions on DB-15 port........................................................................................13
4) Description on LED of Ethernet Port ..........................................................................13
III. WebEye Installation Summary, Connection & Placing.......................................................14
1. Installation Summary.........................................................................................................14
2. Connecting .......................................................................................................................14
3. Placing.............................................................................................................................14
IV. Installing WebEye Setup Program ......................................................................................14
V. Assigning IP Address and Configuring Administrator’s Condition......................................15
1. Connecting WebEye to a PC ..............................................................................................16
1) Connecting WebEye on Internet or LAN. ....................................................................16
2) Connecting WebEye to a PC.......................................................................................16
2. Assigning IP address and Configuring administrator’s condition with Setup program ............17
1) Starting Setup Program for WebEye ............................................................................17
2) Configuring Administrator’s Conditions .....................................................................18
3. Assigning IP Address with ARP command .........................................................................18
1) Using ARP in Windows 98 and NT ............................................................................18
2) Using ARP in Windows 95 ........................................................................................18
3) Verifying Installation .................................................................................................18
VI. Accessing WebEye Homepage & Monitoring Real-time Image ...........................................20
1. Starting Web browser ........................................................................................................20
2. Login page ........................................................................................................................20
1) ID and password........................................................................................................20
2) Behind Firewall.........................................................................................................20
3) WebEye Plug-in for Netscape user..............................................................................21
4) WebEye Active-X for MS Explorer User ....................................................................21
5) WebEye Java Applet for Macintosh or Unix system user. .............................................21
6) FAQ .........................................................................................................................21
3. Various viewers in WebEye homepage................................................................................22
1) Real-time monitoring through default viewer ..............................................................22
4
WebEye E10/E104 User’s Guide
2) Real-time monitoring through normal viewer ..............................................................24
3) Real-time monitoring through simple viewer ...............................................................27
4) Real-time monitoring through server-push viewer .......................................................28
5) Real-time monitoring through java applet viewer .........................................................29
6) Real-time monitoring through snapshot viewer ............................................................30
VII. Configuring Administrator’s Condition at WebEye Homepage ......................................... 31
1. Administrator Login..........................................................................................................31
1) Accessing through setup program ...............................................................................31
2) Accessing through Web browser .................................................................................31
2. Configuring Administrator’s Condition at Homepage ..........................................................32
1) System Configuration ................................................................................................32
2) User Configuration ....................................................................................................33
3) Network Configuration ..............................................................................................34
4) Dynamic IP registration service for ISDN and xDSL users...........................................35
5) How to find registered WebEye in WebEye Internet homepage.....................................36
6) Security Configuration...............................................................................................38
7) Video Configuration ..................................................................................................39
8) Application Configuration..........................................................................................40
9) Pan/Tilt/Zoom Configuration .....................................................................................43
10) Serial Port Configuration .........................................................................................44
11) Digital I/O Configuration.........................................................................................46
12) Alarm Configuration................................................................................................47
13) User Custom Configuration......................................................................................47
14) Goto Viewer Page....................................................................................................48
VIII. Convenient Functions of Mouse (Pop-up menu)...............................................................49
1. Image Info ........................................................................................................................49
2. Quality Box ......................................................................................................................49
3. Focus sensitivity ...............................................................................................................49
4. Image quality....................................................................................................................49
5. Save File As .....................................................................................................................50
IX. Adjusting Focus...................................................................................................................51
1. WebEye E104 ...................................................................................................................51
2. WebEye E10 .....................................................................................................................51
Appendix
Detailed Specifications of WebEye E10 ..................................................................................... 52
1. General.............................................................................................................................52
2. CCD Module ....................................................................................................................52
3. Network ...........................................................................................................................53
4. Mechanical .......................................................................................................................53
5
WebEye E10/E104 User’s Guide
5. Environmental..................................................................................................................53
6. Compatible external devices and software...........................................................................54
Detailed Specifications of WebEye E104.................................................................................... 55
1. General.............................................................................................................................55
2. CCD Camera ....................................................................................................................55
3. Network ...........................................................................................................................56
4. Mechanical .......................................................................................................................56
5. Environmental..................................................................................................................56
6. Compatible External Devices and Software.........................................................................57
Frequently Asked Questions ......................................................................................................58
1. About WebEye's Feature ....................................................................................................58
2. About Installing and Running WebEye. ..............................................................................59
Utilizing IP Addresses on Local Network..................................................................................64
1. Introduction ......................................................................................................................64
2. IP Construction and Network Class ....................................................................................64
3. C-class Network ................................................................................................................65
Upgrading WebEye Firmware .................................................................................................. 67
1. Connect WeEye to a PC. ....................................................................................................67
2. Upgrade firmware with upgrading program.........................................................................68
6
WebEye E10/E104 User’s Guide
I. Introduction
• What is WebEye ?
The WebEye is a camera server with an integrated Internet server, image compression device, built
in CCD, flash memory, and many other features. No other hardware is necessary for use. The
WebEye connects directly to a network and provides real time images over networks and the
Internet. Simply provide power and connect LAN cable to the WebEye. WebEye utilizes Wavelet
image compression and Linux operating system. Wavelet and Linux enable WebEye to transfer
high quality images faster and with a greater degree of reliability than standard JPEG systems.
• Features and Benefits
Ease of Use – WebEye requires either Netscape Navigator 4.7 (or higher) or Microsoft Internet
Explorer 5.0 (or higher) for use. Windows 2000 is recommended for best results. Connect WebEye
to the Internet and it is ready for use.
Compatible with most Systems and Protocols – WebEye supports TCP/IP networking, SMTP,
HTTP and other Internet-related protocols. In addition, the WebEye can be used in mixed operating
system environments, such as Windows, UNIX, Macintosh and OS/2. WebEye also integrates
easily into other Internet/Intranet applications and CGI scripts.
Simple Administration - WebEye can be configured and managed directly from its own web page.
Moreover, as new upgrades become available, it is easy to upgrade all WebEye camera products
remotely over the network.
Wavelet Image Format - Unlike many other products that need to fracture image files prior to
broadcast, the WebEye delivers complete, highly compressed pictures in Wavelet format. Wavelet
has image compression rates 30-300% higher than standard JPEG. By utilizing Wavelet, image file
sizes are much smaller than conventional camera servers and Wavelet's image quality is superior to
other camera servers as well. Wavelet can transmit up to 123 frames per second.
External Device Connection - External devices such as IR-sensors, switches, alarm relays and
external video input can be connected to WebEye via the auxiliary Input/Output port.
User’s Programmable Space – WebEye contains 4.5MB of configurable Flash Memory for
user-programmable and user-configurable space. Because WebEye also acts as a server, this space
can be used to create a personal web page.
Embedded Linux Operating System – WebEye uses an embedded Linux operating system within
its 32bit RISC CPU. Linux is based on UNIX and is one of the most stable operating systems
available. There is very little chance of the operating system crashing.
7
WebEye E10/E104 User’s Guide
II. Product Description
1. WebEye E104
1) Contents
* Unpack and check all the items as below.
Item
Description
Remarks
WebEye
Web server camera
AC Adapter & Power cable
DC 12V, 1A
Lens
8mm, f 1.3, C mount
WebEye User's Guide
Quick reference guide
Already assembled
Provided on CD
Printed material
Crossover Cable
Direct Cable
1 m crossover cable
2 m direct cable
Red-colored
White -colored
Plug & Holder
Plug & holder for DB-15
Wrench
L-shaped hexagonal wrench
CD ROM title
Setup program and manual
Manual
WebEye E104 only
2) Rear View and Descriptions
Connector Name
Description
Remark
DIP switch
To configure the function of ‘CH1 BNC connector’ and to
designate video signal termination of all four BNC connectors.
CH1 BNC connector
CH2 BNC connector
To output or input video signal through a coaxial cable.
To input video signal through a coaxial cable.
CH3 BNC connector
To input video signal through a coaxial cable.
8
WebEye E10/E104 User’s Guide
CH4 BNC connector
To input video signal through a coaxial cable.
To supply power connecting provided SMPS power supply
unit (12V 1.0A)
To connect external devices such as pan/tilt/zoom
mechanism, sensor, video iris lens, digital device, etc.
To connect 10 Base-T Ethernet cable.
Power connector
DB-15 port
RJ-45 Ethernet port
3) Descriptions on DB-15 port
5
4
3
GND
S-
S+
2
10
9
8
O1+
I2-
I2+
15
14
EM
GND
1
RXD
13
IRIS
TXD
7
6
I1-
I1+
12
11
+12V
O1-
Pin No.
Pin Name
Description
1, 2
TXD, RXD
To communicate between external devices such as PTZ controller and
WebEye E104. These pins are for devices that satisfy RS-232 standard.
3, 4
S+, S-
To communicate between WebEye E104 and external devices that
satisfies RS-485 standard. They are half-duflex. The ports are used to
connect several PTZ controller s.
5, 14
GND
To ground cables of power, communication, IRIS, etc.
6, 7
I1+, I1-
To connect external devices such as infrared sensors.
8, 9
I2+, I2-
10, 11
O1+, O1 -
12
+12V
To connect external devices such as infrared sensors.
To control external electric device. They are 1 pair of SSR (Solid State
Relay) output ports.
To supply power to external devices such as an auto iris driver or a
sensor.
13
IRIS
To transmit video iris signal from WebEye E104 to auto iris lens.
15
EM
To maintain firmware of WebEye E104.
4) Description on LED of Ethernet Port
Yellow LED: This LED indicates the status of data transmission.
After power is supplied, it is on for the first 4-5 seconds and then
it goes off. And it blinks continuously when a user access
WebEye and WebEye transmits data.
9
WebEye E10/E104 User’s Guide
Green LED: This LED indicates the status of networking. After power is supplied, it is on for the
first 1-2 seconds, and then it blinks once at every one second as long as the network is connected.
Phenomenon of Malfunction
1. Network Malfunction
• Green LED blinks once at every 4 seconds
• Check if Ethernet cable is connected properly or the Network works.
2. Software Malfunction
• Green and yellow LEDs are on, and they blink 6 times rapidly at every 10 seconds.
• This pro blem is to be solved with A/S program. Contact the dealer from who you bought
WebEye.
• After being on for a second, Green and yellow LEDs blink 6 times rapidly. Then green
LED is on and yellow LED is off.
• This problem is to be solved by re -installing firmware. Visit WebGate’s Internet homepage
to download the firmware and install it on your WebEye.
5) Descriptions on DIP Switches
• OUT / IN
To configure the function of the first coaxial cable port at the rear of WebEye.
If you set the switch at position ‘OUT’, the first port can be used to transmit video signal from
WebEye’s inner CCD module to outer displayer such as TV or computer monitor. Setting the first
DIP switch at ‘OUT’ and the second DIP switch at ‘OFF’, you can connect an outer displayer
directly to the first port with coaxial cable. In this case, you may monitor 4 channels (Ch.0, Ch.2,
Ch3, and Ch.4) in WebEye’s Homepage through network and also can monitor a channel (Ch.0) on
outer displayer with motion pictures sent from WebEye’s inner CCD module. It means that WebEye
could not receive video signal from an external camera, connected to the first coaxial cable port,
though.
If you set the switch at position ‘IN’, the first port can be used to receive video signal from external
CCD camera. Setting the first DIP switch at ‘IN’ and the second DIP switch at ‘ON’, you can
10
WebEye E10/E104 User’s Guide
connect an external CCD camer a directly to the first port with coaxial cable. In this case, you may
select and monitor 2 types of 4-channel video sources. The first one is of Ch.0, Ch.2, Ch.3, and Ch.4,
and the other is of Ch.1, Ch.2, Ch.3, and Ch.4. Difference is Ch.0 that shows video signals from an
inner CCD of WebEye, and Ch.1. that shows video signals from an external CCD camera. You can
select which channel to use through ‘WebEye Setup Program’ or ‘Configuring Administrator’s
Condition at Homepage’ (Refer to Chapter V and VII)
• ON / OFF
To designate video signal termination. This is for expanded usage. If you want to connect external
CCD camera to CCTV monitoring system as well as WebEye, you can use T-type coaxial cable
jack. In this case, you should decide which one is terminal of video signal. WebEye is not affected
if the CCTV system is designated as terminal. However, CCTV system is affected if the WebEye is
designated as terminal. CCTV monitor will show vague image if it is not designated as terminal.
If you want to connect 4 external cameras to coaxial cable ports of WebEye and CCTV system at
the same time, you use T-type coaxial cable jack to WebEye’s coaxial cable port. In this case, you
should place 4 switches of 1, 2, 3, and 4 at the position of ‘OFF’. T-type jack has 3 ports to connect
coaxial cables from WebEye, an external CCD camera, and CCTV system.
If you want to connect 4 external cameras only to WebEye, you should place the switches at ‘ON’
Video signal flows
through LAN Cable.
CCTV Monitor
PC
Video signal flows through
Coaxial cable. For this
application, use a T-shaped
BNC connector.
CCTV Camera
T-shaped connector
11
WebEye E10/E104 User’s Guide
2. WebEye E10
1) Contents
* Unpack and check all the items as below.
Item
Description
WebEye
AC Adapter & Power cable
Lens
Remarks
Crossover Cable
Web server camera
DC 5V, 1.5A
3.8mm, f 2.0, fixed
WebEye User's Guide
Quick reference guide
1 m crossover cable
Already assembled
Provided on CD
Printed material
Red-colored
Direct Cable
2 m direct cable
White -colored
Plug & Holder
Plug & holder for DB-15
Stand
Stand for WebEye E10
CD ROM title
Setup program and manual
Manual
WebEye E10 only
2) Rear View and Descriptions
Connector Name
Power connector
DB-15 port
RJ-45 Ethernet port
Description
Remark
To supply power connecting provided SMPS power supply
unit (5V 1.5A)
To connect external devices such as external camera,
pan/tilt/zoom mechanism, sensor, digital device, etc.
To connect 10 Base-T Ethernet cable.
12
WebEye E10/E104 User’s Guide
3) Descriptions on DB-15 port
Pin No.
Pin Name
Description
1, 2
TX, RX
To communicate between external devices such as PTZ controller and
WebEye E10. These pins are for devices that satisfy RS-232 standard.
3, 4
TX, RX
To communicate between external devices such as PTZ controller and
WebEye E10. These pins are for devices that satisfy RS-232 standard.
5, 14
GND
6, 7
I1+, I1-
To connect external devices such as infrared sensors.
8, 9
I2+, I2-
To connect external devices such as infrared sensors.
10
VOUT
To connect a CCTV monitor directly to WebEye E10.
11
VIN
To connect an external camera.
12
13, 15
+5V
NC
To supply power to external devices such a sensor.
No function pins.
To ground cables of power, communication, IRIS, etc.
4) Description on LED of Ethernet Port
Please refer to WebEye E104.
13
WebEye E10/E104 User’s Guide
III. WebEye Installation Summary, Connection & Placing
1. Installation Summary
l
l
l
l
l
l
Connect Ethernet and Power to WebEye on local network for configuration
Install a setup program for WebEye in to a PC on local network
Assign an IP address to WebEye and configure administrator’s condition
Configure user’s condition
Place WebEye for your purpose, and re-connect power and Ethernet
Adjust the Focus
2. Connecting
l Connect Ethernet line to the Ethernet port in the rear.
l Connect the power supply to a power supply port in the rear .
l Confirm that the LED of the Ethernet port blinks
3. Placing
l Place WebEye appropriately for your purpose
* Use a general camera stand or tripod for WebEye.
Warning
WebEye is for indoor use. The built in CCD (charged coupled device) can be damaged permanently
if the camera lens is exposed to direct sunlight. When the WebEye is placed under glaring light, an
iris lens is recommended.
If your application demands prolonged exposure to sunlight, consider using a sun visor.
IV. Installing WebEye Setup Program
l Insert the WebEye Setup disk.
l Drag the WebEye Setup icon onto the desktop.
l Double-click on the icon.
14
WebEye E10/E104 User’s Guide
V. Assigning IP Address and Configuring Administrator’s Condition
Important
To access WebEye, you firstly have to assign an appropriate IP
address. When you assign an IP address to WebEye, make sure to
use unoccupied IP address, and not to use the default or example
IP address.
Terminology
IP Address
IP address is an identification code for computers and devices on a TCP/IP network. Networks
using TCP/IP protocol route messages based on the IP address of the destination. Within a
closed network, IP addresses can be assigned at random as long as each one is unique. However,
connecting a private network to the Internet requires using registered IP addresses to avoid
duplicates. IP address can be acquired from a network administrator or an Internet service
provider.
MAC Address (Media Access Control Address)
MAC address is a hardware identification code that uniquely identifies each node of a network.
The MAC layer interfaces directly with the network media. Consequently, each type of network
media requires a different MAC layer. The MAC address of WebEye is a 12-digit number. A
unique MAC address can be found on the label at the bottom of each WebEye.
Crossover Cable
The crossover cable (red) provided with the WebEye is used to connect the WebEye with a PC.
A HUB is not necessary to connect the WebEye to a PC if a crossover cable is used.
Direct Cable
The direct cable (white) should be used if a HUB is used as an intermediary between the
WebEye and PC.
15
WebEye E10/E104 User’s Guide
1. Connecting WebEye to a PC
1) Connecting WebEye on Internet or LAN.
You may use direct cable (white colored one) to connect WebEye E10/E104 on Internet or LAN.
With this connection remote user may not access WebEye before local user configure its network
setting.
Internet
Dedicated line, xDSL line, cable
modem line, ISDN line, and PSTN
(telephone) line are available.
Router
HUB
Remote User
Direct cable
Local User
Connect WebEye to a
PC through a HUB.
2) Connecting WebEye to a PC.
Use the crossover cable (red colored one) to directly connect WebEye E10/E104 to a PC. This
connection is to be used to configure WebEye.
Crossover cable
Connect WebEye directly to
a PC through LAN ports.
16
WebEye E10/E104 User’s Guide
IP Address Assigning Methods
n With setup program
• Assemble and place WebEye
• Assign IP address to WebEye using setup program on local network.
• Access WebEye through Web browser with the IP address and configure user’s condition
and administrator’s condition.
• If it is impossible to assign IP address with setup program, try it with ARP command
n With ARP command
• Assemble and place WebEye
• Assign IP address using ARP command on local network
• Access WebEye through Web browser with the IP address and configure user’s condition
and administrator’s condition.
2. Assigning IP address and Configuring administrator’s condition with Setup program
1) Starting Setup Program for WebEye
Click the “WebEyeSetup.exe”
file on your PC. When the Setup
Program is executed, the setup
program detects and shows every
WebEye connected on the local
network.
From the WebEyes listed, select
one to assign a new IP address.
(Default is 211.53.133.92).To
choose a WebEye, click on its
MAC Address or IP addres
When a WebEye is selected, its
IP address will appear in the
‘Selected IP Address’ box. Type
a password in the “Admin’s
Password” box to change the IP
address, reboot WebEye, or start
configuration.
The default password is “admin”.
17
WebEye E10/E104 User’s Guide
To change the IP address, enter the Admin’s password
and click “Change IP Addr.” Enter the new IP address
and click “OK.”
The “Reboot” button will reboot the WebEye. This process
takes 10-20 seconds.
2) Configuring Administrator’s Conditions
To access the WebEye’s Administrator’s Page from the Setup Menu, enter
the admin.’s password and click the “Start Configuration” button. (For
more detailed information, refer to Chapter VII “Configuring Administrator’s Condition at
Homepage”)
3. Assigning IP Address with ARP command
1) Using ARP in Windows 98 and NT
When using WebEye with Windows 98 and Windows NT, follow the steps below.
• Open a DOS window and type the following commands.
Arp -s <WebEye IP address> <WebEye Ethernet address>
Ping -t <WebEye IP address>
• Example
Arp -s 192.168.1.3 00-40-8c-10-00-86
Ping -t 192.168.1.3
2) Using ARP in Windows 95
When using WebEye with Windows 95, follow the steps below.
• Open a DOS window and type the following commands.
Arp -s <WebEye IP add.>
Ping <WebEye IP address>
<WebEye Ethernet add.> < my PC IP add.>
• Example
Arp -s 192.168.1.3 00-40-8c-10-00-86 192.168.1.2
Ping 192.168.1.3
3) Verifying Installation
After successfully completing the above procedures, the following message (or similar) will appear
on the screen:
18
WebEye E10/E104 User’s Guide
Request timed out
:
Request timed out
Reply from 200.243.232.178: bytes=32 time=2ms TTL=255
Reply from 200.243.232.178: bytes=32 time=2ms TTL=255
Ping statistics for 200.243.232.178:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milliseconds:
Minimum = 1ms, Maximum = 2ms, Average = 1ms
If the above “ping” reply does not appear, press 'F3' and 'Enter' keys. Normally “Request timed
out” messages appear 7 times before reply ing properly.
Once the above “ping” reply appears press <Ctrl>+<C> keys to make it stop.
When the “ping” reply stops, data loss may range from 0% to 99%. This is normal. If the statistic
shows ‘100% loss’, check the following criterions: (a) network line and connection status are
stable; (b) IP address assigned to WebEye is available; (c) PC and WebEye have the same local
network IP address. Same local IP address of C grade network means that first 3 sets of numbers
are the same but the fourth set is different. For example 192.168.1.2 and 192.168.1.3 are in the
same local network. (If there is a ‘Network Mask’ on the network, this can be an exception. For
detailed information on IP, refer to appendix 4)
19
WebEye E10/E104 User’s Guide
VI. Accessing WebEye Homepage & Monitoring Real-time Image
After assigning WebEye an IP address, you may access WebEye and monitor real-time image on
Internet. However you may not access its Homepage on remote network until assigning other
addressees like gateway address, subnet mask, broadcast address properly.
1. Starting Web browser
Start your web browser and enter your WebEye IP address. Then you can see a build-in homepage
of WebEye.
• Example
http://200.243.232.178/
WebEye supports up to 100 users simultaneously. If a person tries to access WebEye as the 101st
user, one cannot receive any image but will see a message of user counter on upper right side of
homepage as ‘Connected Client#: 100’
2. Login page
1) ID and password
To verify registered WebEye users,
there is a Login page. If you are to
connect to WebEye, you should
follow login procedures.
If you key in user’s ID and
password, you may access to a
viewer to monitor real-time images.
With administrator’s ID and
password, you may also access to a
real-time image viewer with
administrator’s authority.
The default value of both user ’s ID
and password are ‘guest’, and
administrator may change it at
Admin page. But, each ID and password must be composed within 9 bytes. (e.g. 9 English letters)
2) Behind Firewall
If your PC is connected on a network where firewall is. In the case, you may not view real time
image properly because video TCP port of WebEye is blocked. Common video TCP port (A default
video TCP port of WebEye is 8080 t h port.) is blocked under firewall. If you are under firewall, you
20
WebEye E10/E104 User’s Guide
may view real time image through WebEye’s Server Push Viewer that transmits video through Web
TCP port instead of video TCP port.
By clicking on ‘Behind Firewall’ menu, you may directly connect Server Push Viewer when you
access WebEye homepage.
3) WebEye Plug -in for Netscape user
To monitor real-time image through Netscape Navigator , user should install WebEye Plug-in
program first by clicking WebEye Plug-in menu. When you connect WebEye for the first time or
you have Plug-in program of lower version, you have to download it clicking ‘Download WebEye
Plug In Now!’ button. Then you click ‘Grant’ and ‘Install’ buttons respectively. When you access
WebEye with lower version, you may not monitor properly. In the case, download and install
Plug-in program again.
4) WebEye Active -X for MS Explorer User
For a Microsoft Explorer User, Active-X Control program is required. The program will be installed
automatically when a user accesses to WebEye. For Active-X installation on your PC, just click
‘Yes’ to the question if you want to install the program on pop-up window. If you cannot see
images after installation, you should check if Active-X Control program (a file named Web Camera
Server Control) is installed or not. You may check Web Camera Server Control file (Active-X
Control program) in the fold of C:\Windows\Download Program Files. If the Web Camera Server
Control file is not installed at all in the directory, try it again to download and install it. If the file is
already installed but image is not seen, remove the file and re-install it.
Plug-in and Active-X Installation
If the Plug-in or Active-X program fails to be installed automatically, you may install it
manually. The manual installation program is provided at ‘Client Support’ page in WebGate’s
Internet homepage. (http://www.webgateinc.com)
The installation will not take more than 1 minute. Please, don’t click any button until the
installation is completed.
5) WebEye Java Applet for Macintosh or Unix system user.
Java applet viewer is for a user who accesses WebEye through a computer that dose not utilize MS
Windows (OS) such as Macintosh computer, etc. Java applet viewer is run with java virtual
machine that is installed on User’s computer.
6) FAQ
A lot of questions and answers are provided here for troubleshooting. If user has another question
that is not answered here, please contact WebGate through its Internet homepage.
21
WebEye E10/E104 User’s Guide
Macintosh and Unix System
WebEye Active-X and Plug-in program is based on MS Windows OS. Therefore it is
impossible to access WebEye and monitor real time image through default viewer. If a user
access WebEye through Macintosh or Unix systems, WebEye detects that OS is not MS
Windows. And it operates java based image viewer to show real time image. The design is same
to default viewer, b ut some functions are not work for now.
If you have any problem in monitoring real time image, please refer to FAQ for troubleshooting. The
document is provided at ‘Client Support’ page in WebGate’s Internet homepage.
(http://www.webgateinc.com )
3. Various viewers in WebEye homepage
There are 6 viewers of real-time monitoring in WebEye homepage. An administrator may set 3
different viewers as a main viewer out of the 6 viewers. User may monitor real-time images through
a viewer that is set as a main by administrator.
6 viewers are default viewer, normal viewer, simple viewer, server-push viewer, java applet viewer,
and snapshot viewer. And an administrator may select a default viewer, a normal viewer, or a
simple viewer as a main viewer
1) Real-time monitoring through default viewer
At default viewer, user may also
choose a viewer among all 6
viewers. Therefore general user
may use a certain viewer for one’s
convenience.
Especially, this default viewer is
designed of HTML and server -side
script, so administrator may
change page easily.
(1) Real-time monitoring.
User monitors real-time images
clicking ‘here’ menu after setting
channel, resolution, expansion, and
frame rate.
22
WebEye E10/E104 User’s Guide
Channel selection
It is to select channels to monitor. User may select a certain channel or all 4 channels (WebEye E10:
between 2 channels).
Resolution
User may select a level of resolution among 5 levels (720x486, 720x243, 360x243, 180x121,
90x60). High-resolution image is big, and it is transmitted at slow speed.
Expansion
User sees image in different sizes from 1X to 4X. However, Expansion (2X to 4X) does not
increase image’s resolution, but rather enlarges its size. Therefore, the quality of extended image is
not as clear as original one.
Frame rate
User chooses image transmission speed. If you choose ‘F astest’, you can get images at fastest speed
under your network environment. The transmission speed depends much on network line’ s capacity
and user PC’s performance. WebEye transmits maximum 30 frames per second, and total frames
transmitted by all 4 channels cannot surpass the maximum rate of 30 fps.
(2) Changing with other image viewers
User may monitor real-time image through other viewers such as simple viewer, normal viewer,
server -push viewer, java applet viewer, and snapsho t viewer.
Normal viewer and simple viewer
User can utilize various functions of pan/tilt/zoom control, gray-image transmission mode,
progressive transmission mode, etc. And simple viewer is designed very simple compared to normal
viewer, so the viewer is recommended to a user who uses low speed network line.
Server push viewer
If user’s PC is connected on network where a firewall is, the user may view real time image through
server push viewer. If you access server push viewer, real time images are transmitted through Web
TCP port. So images are to be transmitted at lower frame rate than that of simple viewer or normal
viewer. You may utilize almost the same functions that of normal viewer or simple viewer.
More service
Clicking others menu, user may see explanation on normal, simple, server-push, java applet, and
snap shot viewers. Java applet viewer is for a user who accesses WebEye through a computer that
does not utilize MS Windows OS such as Macintosh computer, etc. And snapshot viewer is to see
still image beforehand accessing WebEye homepage.
23
WebEye E10/E104 User’s Guide
(3) Accessing administration page
Clicking ‘Administration’ menu, you go to a login page of administration page. However only the
user who has authority as an administrator can access the page with administrat or’s ID and
password.
(4) Plugin
As WebEye compresses image with Wavelet algorithm, user need to install Plug-in program from
WebEye to see transmitted image on Netscape Navigator on one’s PC. Clicking ‘Plugin’ menu, a
user accesses a page where to download Plug-in program.
(5) FAQ
User may refer FAQ for trouble-shooting in installing or running WebEye.
(6) Version
User may look up information on software versions clicking.
(7) Placing a company logo and hyper-linking
WebGate company logo, which is located on the left top in the viewer, can be replace with user’s
company logo. User designates one’s company homepage to be connected through a hyper-link on
the logo. (Refer to Chapter VII for detailed information)
2) Real-time monitoring through normal viewer
After Login, user sees real-time images with various menu buttons to configure monitoring
conditions for user’s convenience.
(1)
(2)
(3)
(4)
(5)
24
WebEye E10/E104 User’s Guide
(1) Single View / Multi View
In case that you connect external CCTV cameras, you can see 4 screens of
real-time images at the same time. (2 screens with WebEye E10). For view
selections, click on the appropriate button for single view or multi view.
(2) Camera Selection
If you connect CCTV cameras to the external video ports in your WebEye,
you can select and see each real-time image with these camera selection
buttons.
(3) Play Control
Pan/Tilt
If you click the buttons, you can move the direction of WebEye to where
you want to see.
4 direction arrows
You may change direction right/left and up/down.
Zoom
You may zoom in and zoom out.
Focus
You may control and optimize the image’s focus.
Accel.
You may choose moving speed of Pan / Tilt mechanism with ‘Accel + or
-’ buttons among three steps. The step selected is shown as graphic
beside the ‘Accel’ text. However you cannot control zooming speed with
these buttons. You may set zooming speed with your mouse. By clicking
the right button, a pop-up window of 5 menus appears. Among them, you
may do the setting with ‘Focus Sensitivity’ menu. You can select a
certain level among ten.
PLAY/STOP
WebEye generates and transfers the real-time images as soon as you access it. If you want to stop
transferring images to your PC, click the STOP button. And click ‘PLAY’ button to resume.
(4) Transmission Control
Gray Mode
If you choose this mode, the images are displayed in black and white.
And, you can view the images transmitted faster.
Progressive Mode
In the case of ‘Progressive Mode’ on, every image is regenerated from
25
WebEye E10/E104 User’s Guide
low to high resolution. In other words , an image is reproduced from vague to clear for user see what
is happening and later one may detect exact things. This function is useful when you use a low
speed network, because it reduces waiting time.
Single Shot Mode
When this button is clicked, one frame of image is reproduced. Therefore, no other images may be
viewed. To go back to the real-time images, click the button again
(5) Image Control
Resolution
You may choose a certain resolution among levels . If you choose
lower resolution rate, you can see image faster .
Extension
You may see images in different sizes 1X to 4X. However, Extension
(2X to 4X) does not increase image’s resolution, but rather enlarges its
size. Therefore, the quality of extended image is not as clear as original
image.
Frame Rate
You may choose image transmission speed. If you choose ‘Fastest’, you
can get images at fastest speed. The transmission speed depends much
on your network line’s capacity and PC’s performance.
(6) Other function buttons
Download
This button leads to a page where to download updated Netscape Plug-in program of WebEye.
Capture
This is to save a frame of still image that is transmitted from WebEye. A
still image can be saved as a format of bitmap (*.bmp) or Wavelet
method file (*.eye). Wavelet compression image file can be
decompressed and reproduced on Internet browsers such as Netscape or
Explorer. There is another method to capture a still image. After placing
your mouse on the picture, click the right button of your mouse. Then a
fly box appears. Then click ‘Save As File’
To Home
This button is to return to a default viewer.
26
WebEye E10/E104 User’s Guide
FAQ
If user has any problem to install and run WebEye, one can find a solution with this button.
Admin
This button is to access administration page. (Refer to Chapter VII ‘Configuring Administrator ’s
Configuration at Homepage’)
3) Real-time monitoring through simple viewer
Simple viewer has the same functional menus as normal viewer does. Simple viewer is designed
very simple graphics so that its size is decreased dramatically to overcome low speed transmission.
(1)
(2)
(3)
(4)
(5)
(1) Single View / Multi View
User may select a mode between single view and multi view. The button is toggled between the two
functions. Usages are same as normal viewer. Please refer to descriptions on normal viewer.
(2) Image Control
Usages are same as normal viewer. Please refer to descriptions on normal viewer.
(3) Camera Selection
Usages are same as normal viewer. Please refer to descriptions on normal viewer.
(4) Transmission Control
Usages are same as normal viewer. Please refer to descriptions on normal viewer.
(5) Play Control
Usages are same as normal viewer. Please refer to descriptions on normal viewer. Play and Stop
functions are toggled on the same button.
27
WebEye E10/E104 User’s Guide
(6) Other function buttons
Usages are same as normal viewer. Please refer to descriptions on normal viewer.
4) Real-time monitoring through server-push viewer
If WebEye is installed on a network where firewall is, you may access WebEye through server-push
viewer to monitor real-time images. If you have information on the network such as which port is
block with firewall, you may access with default/normal/simple viewer by changing Web TCP port
or video TCP port. For changing TCP port, please refer to Chapter VII ‘Configuring
Administrator’s Configuration at Homepage’.
(1)
(2)
(3)
(4)
(1) Image Control
On server-push viewer, there is not ‘Image extension’ menu. Other usages are same as normal
viewer. Please refer to descriptions on normal viewer.
(2) Camera Selection
On this viewer, there is not ‘Multi Viewer ’ menu. Other usages are same as normal viewer. Please
refer to descriptions on normal viewer.
(3) Transmission Control
On this viewer, there is not ‘Progressive Mode’ menu. Other usages are same as normal viewer.
Please refer to descriptions on normal viewer.
(4) Play Control
This is to control PTZ mechanism. Usages are same as normal viewer. Please refer to descriptions
on normal viewer.
28
WebEye E10/E104 User’s Guide
(5) Other function buttons
Usages are same as normal viewer. Please refer to descriptions on normal viewer.
5) Real-time monitoring through java applet viewer
Java applet viewer is for the users who access WebEye through a computer that dose not utilize MS
Windows OS such as Macintosh computer, etc. Java applet viewer is run with java virtual machine
that is installed on User’s computer.
(1)
(2)
(3)
(4)
(1) Connect/Disconnect
After defining other conditions such as image control and transmission control, user monitors
real-time images clicking ‘Connect’ button. This button is toggled to ‘Disconnect’ when a user
accesses WebEye.
(2) Image Control
On this viewer, there is not ‘Frame Rate’ control menu. Other usages are same as normal viewer.
Please refer to descriptions on normal viewer.
(3) Transmission Control
On this viewer, there is only a ‘Gary Mode’. The usage is same as normal viewer. Please refer to
descriptions on normal viewer.
(4) Camera Selection
On java applet viewer, there is not ‘Multi Viewer ’ menu. Other usages are same as normal viewer.
Please refer to descriptions on normal viewer. ‘CH 0’ is for internal camera and ‘CH 1’ is for
external camera that is connected to ‘CH 1’ in the rear of WebEye E104. For WebEye E10, Ch1 is
29
WebEye E10/E104 User’s Guide
for the camera that is connected to video input. Therefore ‘CH 1’ screen can be seen when external
camera is connected to WebEye.
6) Real-time monitoring through snapshot viewer
Snapshot viewer is to see still image and
check the situation without monitoring
real-time motion pictures through other
viewers.
With default source, a user sees snap
shot image from internal CCD (Ch0).
And user may view image from other
channel by changing its source.
There are two methods of snapshots.
One is to see a single image fixed, and
the other is updating image in every 3
seconds. A user may also differ updating
period by changing its source.
A user makes hipper link this menu at other Internet homepage to monitor the WebEye.
30
WebEye E10/E104 User’s Guide
VII. Configuring Administrator’s Condition at WebEye Homepage
This page is for administrator. Administrator may control operating status remotely. This page can
be accessed through Setup program by clicking ‘Start Configuration’ button.
1. Administrator Login
1) Accessing through setup program
First you click on MAC address or IP address of WebEye to select a certain one. Then you key in
the administrator’s ID and password (Default ID and password are ‘admin’), and click ‘Start
Configuration’ button in turns. When you click ‘Start Configuration’ button, the setup program
automatically connects you to Admin page of WebEy e Homepage. (For more detailed information
how to access the page through Setup program, refer to Chapter V ‘Assigning IP address and
Configuring Administrator’s Condition’)
2) Accessing through Web browser
On Web browser, a user may access
WebEye login page with its IP
address. In the login page, a user
may key in administrator’s ID and
password or a normal user ’s ID and
password. With any of ID and
password, the user may access real
time image viewer page.
However administrator can monitor
and control real time image viewer
with administrator’s authority. And
a normal user may monitor and
control the viewer page with
assigned authority. If a normal user goes to administration page, one
should pass login page again to key in administrator’s ID and
password while administrator may access the administration page
directly.
Both default administrator’s ID and password are set as ‘admin’, and
administrator and users accounts (ID and password) are to be changed
in administration page. But, each ID and password must be composed
within 9 bytes. (e.g. 9 English letters)
In the administration page, there are 12 sub-pages where to configure
WebEye operating conditions. It is very import to configure the
conditions properly to utilize WebEye well. The last menu ‘Goto
Viewer Page’ is to go back to real time image viewer.
31
WebEye E10/E104 User’s Guide
2. Configuring Administrator’s Condition at Homepage
1) System Configuration
This page is to set name, date &
time, location, and description of
one’s WebEye. Model, serial
number and software version
appear automatically.
(1) WebEye Name
The name is to be used to register
the WebEye on a certain server, if
you use dynamic IP address.
Therefore it is very important to
set a proper name for user to find
the WebEye in the dynamic IP
registration list. (For detailed information, refer to ‘Dynamic IP Registration Service for ISDN,
xDSL User’)
(2) Model
By clicking ‘Detailed H/W Information’, you may view detailed hardware information such as
maximum numbers of channel, serial port, digital input, digital output, etc. The model name is
marked automatically.
(3) Video Channel Selection for CAM#1
Administrator may decide if one uses external CCD camera connecting to the port of ‘Ch1’ in the
rear of WebEye E104 or uses self-contained CCD module of WebEye E104. Please keep in mind
that this menu is only for the first port in the rear of WebEye with name ‘CH1’. With WebEye E10,
‘Video Channel Selection for CAM#1’ is not activated. Because ‘CH#0(Internal)’ is fixed to show
video from an inner CCD module and ‘CH#1(External)’ is fixed to show video from an external
CCD camera.
(4) Installation Location & Additional Description
The information is shown in the real time image viewer page as well as in a dynamic IP registration
list.
(5) Date & Time
There are three date & time menus. In ‘WebEye Current Date & Time’ panel, the date and time,
which is set in WebEye, appears. In ‘System (PC) Current Date & Time’ panel, the same date and
time as is set in user’s PC appears. And administrator may set one’s system(PC) ’s date and time into
WebEye by clicking ‘Time Synchronization’ button. In ‘Manual Date & Time’ panel, user may set
date and time. And administrator also synchronizes manually set date and time with ‘WebEye
Current Date & Time’ by clicking ‘Time Synchronization’ button.
32
WebEye E10/E104 User’s Guide
(6) Administrator’s E -mail Address
In this panel, administrator records one’s e-mail address. If administrator put a ‘contact’ menu of
e-mail communication on real time image viewer page, the linked e-mail address to the ‘contact’
menu is to be synchronized with this. So administrator can keep up e-mail address easily.
(7) Initialize Flash Info
Administrator initializes almost all the information saved on flash memory. However ‘Date &
Time’, ’Model’, ‘Serial Number’, IP configuration, passwords, and all items in ‘Video’ menu are
not initialized.
(8) Rebooting
If WebEye has any problem, administrator can reboot it without adjusting power supply. This
button works as on/off switch.
2) User Configuration
This page is to configure IDs and
passwords of an administrator
and 5 users.
(1) User Account
There are one administrator’s
account and 5 users’ accounts.
Account name can be changed.
(2) Password
If you want to open your WebEye to everyone, you may not change default user’s ID and password.
However you should change administrator’s ID and password with unique ones of yours.
ID and Password Limitation
It is very important to compose any ID or password within 9 bytes’ limit. 9 bytes are
equal to 9 English characters.
(3) Access Rights
Administrator may give or forfeit users’ right of PTZ control and video control. With default setting,
administrator has both right of PTZ control and video control and normal user doesn’t have any
right.
• Video control: This is to control pop-up menus such as image information, image quality level
and QBOX settings.
• PTZ control: This is to control ‘Focus Sensitivity’ in pop-up menu and to control PTZ
mechanism of a dome camera.
33
WebEye E10/E104 User’s Guide
3) Network Configuration
This page is to define network type and set network addresses of WebEye.
(1) DHCP Client Protocol
If administrator activates ‘DHCP
Client Protocol’ menu, all the
addresses are going to set
automatically by WebEye detecting
them from DHCP server of your ISP.
The detected addresses are not seen
on the screen. And administrator
needs not to configure all the
address manually.
(2) Select Network Interface
If WebEye is connected on xDSL
line that needs PPPoE process,
administrator should select ‘xDSL
(PPPoE) ’. However the xDSL line
doesn’t need PPPoE process,
administrator
should
select
‘Ethernet’ though WebEye is
connected on xDSL line.
(3) Ethernet Interface
Administrator may configure IP address, subnet mask, broadcast address, gateway address, and
DNS addresses of WebEye. For broadcast address, administrator may set it automatically by
clicking ‘Get From Netmask’ button after assigning IP address and subnet mask. When the
addresses are not assigned properly, any user cannot access WebEye from local or remote network.
Even on the local network, a user is not able to access if administrator does not assign a proper IP
address to WebEye. Please refer to appendix 3 ‘Utilizing IP Address on Local Network’ for more
detailed information.
MTU Size : Depending on network type, administrator may set data packet size with this menu to
utilize the network at most effectively.
DNS Server IP Address: This is used when you register your WebEye on dynamic IP registration
list of WRS (WebEye Registration Server). WRS has its domain name of ‘webeye.to’ and the
domain name is registered on DNS servers on the world. When your WebEye asks the DNS server
on your network, the DNS server resolves the corresponding IP address of ‘Webeye.to’ and informs
the IP address to your WebEye. Then your WebEye may connect WRS. So it is necessary you get
information on DNS server ’s IP address and enter into the blanks.
34
WebEye E10/E104 User’s Guide
DNS (Domain Name System)
DNS (Domain Name System) is to map between IP address and domain name. Every network
device on the world has its IP address to be connected on Internet. And the device is to be
connected not with its domain name but with its IP address. Common users are not familiar
with IP addresses but with domain names.
If a user accesses a certain network device with its domain name, DNS server resolves the
domain name into an IP address of the device and replies the result to the user. A lot of DNS
servers are run on Internet worldwide.
(4) xDSL Interface
If WebEye is connected on xDSL line and needs PPPoE process, administrator should select ‘xDSL
(PPPoE) ’ and configure ID and password for PPPoE. ID and password may be acquired from the
ISP that installed the line. And WebEye may get IP address when it is connected on xDSL line.
4) Dynamic IP registration service for ISDN and xDSL users
This page is to register WebEye on dynamic IP registration server.
If WebEye is installed on a
network of dynamic IP address
(floating IP address), administrator
should register the WebEye to
‘dynamic IP registration server ’ to
give simple connectivity to
common users. If not, no one can
access the WebEye through Web
browser. It is because that no one knows with which IP address one can access the WebEye.
To solve the problem WebGate run a server making a list of WebEyes that have dynamic IP
addresses. On the server, WebEye registers its information such as name, location, and description,
so that common users may detect a certain WebEye. Name, location and description are assigned at
‘System Configuration’ page. If administrator does not change them, the WebEye will register
default information on the list, and it will be very difficult to point out and access a certain WebEye.
The list is on an Internet homepage of WebEye, ‘www.webeye.to’.
(1) Auto IP Registration Function
Administrator may register one’s WebEye by enabling ‘Auto IP Registration Function’.
Registration process is that WebEye detects IP addresses from DHCP server and informs the
detected IP addresses to dynamic IP registration server. And the server updates already registered
information with new one. Please keep in mind that user have to enable ‘DHCP Client Protocol’ at
‘Network Configuration’ page to have WebEye get dynamic IP addresses automatically, when
WebEye is installed on a network of dynamic IP address. With ‘Auto IP Registration Function’
menu, a WebEye of fixed IP address can also be registered on the list.
35
WebEye E10/E104 User’s Guide
(2) Registration Server Address
This is to configure a server address for registrat ion. The registration server to be used for Dynamic
IP registration should be installed proper S/W, developed by WebGate Inc. If you do not run a
server for IP registration, keep the server ’s name as default figure (webeye.to).
(3) Registration Interval
Dynamic IP address is commonly used on xDSL, ISDN or Cable Modem lines. To maintain
continuous connectivity, user should reset the ‘Registration Interval’ shorter than the default value.
Because an IP is to be changed from time to time, some user may not access by clicking on a
WebEye if actual information on WebEye is changed from the registered IP information on the
dynamic IP registration server.
(4) Add Public List
There are two registration systems. One is to register on a public list and another is on a private list.
Please refer to Article 3) ‘How to find registered WebEye in WebEye Internet homepage’ for more
detailed information.
• Public List: This list is open to anyone who accesses WebEye Internet homepage
(www.webeye.to).
• Private List: This list is not seen to anyone. Even the owner of a WebEye can get the
information on one’s WebEye only without viewing information on other’s WebEye.
(5) Access Token
Access token is a password and it is used when you regis ter your own WebEye on a list ‘User’s
WebEye’ out of all WebEyes on WRS(WebEye Registration Server. Please refer to Article 5) ‘How
to find registered WebEye in WebEye Internet homepage’ for more detailed information.
Private List and Access Token
You should set the access token if you configure your WebEye to register its
information on a private list at WebEye Internet homepage (www.webeye.to ).
Otherwise you cannot access the private list nor find the information on your WebEye.
Access token is to be set 9 bytes. 9 bytes are equal to 9 English characters.
5) How to find registered WebEye in WebEye Internet homepage
On WebEye Internet homepage (www.webeye.to), there are menus to find WebEye that is
registered on WRS (WebEye Registration Server).
36
WebEye E10/E104 User’s Guide
(1) Sign up membership
To search your WebEye out of a public list or a private list, you have to sign up membership first.
You may sign up on the server through ‘Membership’ menu.
(2) Finding WebEye from public list
To access WebEye that is registered on public list, you may find it through ‘Service’ or ‘Demo’
menus. Once click ‘Servic e’ or ‘Demo’ menu, you may find ‘WRS (WebEye Registration Service)
WebEye list’ on WRS page that is a main page of the ‘Service’ menu. The sub-menu ‘WRS’ is on
the left side.
You may search your WebEye
with several conditions such as
name, model, location, description,
serial number , and IP address. (‘IP
address’ is to be used only when
you assigned your WebEye a fixed
IP address)
After finding your WebEye, you
may access it by clicking on the
name. By clicking on ‘Preview’,
you may monitor real-time im age from WebEye without logging in WebEye. However ‘Preview’ is
available only when the WebEye is configured to have its ID and password as default values ‘guest’
and ‘guest’.
(3) Finding WebEye from private list
To access WebEye that is registered on private list, you should make your own WebEye list before.
You may make the list through ‘User’s WebEye’ menu. In the list, there are to be registered any
WebEye from the ‘Public List’ or ‘Private List’. On ‘User’s WebEye’ page, there two sub-menus,
‘Your WebEye List’ and ‘Search and Append’.
My WebEye List: You may maintain your own WebEye registering it on this list. When you login
this homepage, WRS (WebEye Registration Server) detects and shows all the WebEyes that you
listed appear on your own list. There for you may access any of them without searching it from
WRS (WebEye Registration Service) list nor verifying access token again. So it is very convenient
to have the list when you run several WebEyes having dynamic IP addresses.
Search and Append: This menu is to append a certain WebEye on your own list. You may append
WebEye on your own list as follows.
• Key in serial number(W100000000000), MAC address(e.g. 00:00:00:00:00:00), and access
token of a certain WebEye in the box.
37
WebEye E10/E104 User’s Guide
• Click ‘Append’ menu.
• WRS (WebEye Registration Server) search a corresponding WebEye with the conditions from
both the ‘Public List’ and ‘Private List’ and registers the WebEye on your own list.
6) Security Configuration
This page is to control accessibility to
one’s WebEye with IP addresses.
(1) IP/Subnet Filtering Mode
If this function is on, only the user
whose PC’s IP address is registered on
WebEye can access the WebEye.
Administrator may temporarily disallow
a registered user to access to WebEye
with a menu on the right side of each IP
address. Any IP addresses are to be
listed.
If administrator inactivates ‘IP/Subnet
Filtering Mode’, anyone may access
one’s WebEye through a Web browser
with any PC.
Principle of ‘IP/Subnet Filtering Mode’
The principle of ‘IP/Subnet Filtering Mode’ is to deny. Therefore WebEye is to deny
every user even the owner if you enabled the function without assigning a certain IP
address to the WebEye.
(2) Image Encryption Mode
Administrator may restrict people to receive images from one’s WebEye, even though people
accessed it. If ‘Image Encryption Mode’ is enabled and a pin number is assigned, people have to
key in the assigned pin number to see image after accessing WebEye image viewers. Encryption
PIN (number or character) should be consisted in 9 bytes. 9 bytes are equal to 9 English characters.
‘Security Configuration’ is a double -checking function to control accessibility, utilizing ‘User
Account Configuration’ at the same time.
38
WebEye E10/E104 User’s Guide
7) Video Configuration
This page is to configure every channel with various conditions.
(1) Video Channel Selection
WebEye El04
User chooses video channels to
configure. In the list, there are 4 video
channels including ‘Ch#0(Internal)’ or
‘Ch#1(External)’ that administrator
selected at ‘System Management’
page.
If administrator selected ‘Ch#0(Internal)’ at
‘System Management ’ page, 4 video channels
of ‘Ch#0, 2, 3, 4’ appear here.
If administrator selected ‘Ch#1(External) at
‘System Management’ page, 4 video channels
of ‘Ch#1, 2, 3, 4’ appear here.
WebEye E10
Different from WebEye E104, WebEye E10 has only two channels as
‘Ch#0(Internal)’ and ‘Ch#1(External)’. ‘Ch#0(Internal)’ is fixed for internal
CCD module, and ‘Ch#1(External)’ is for external CCD camera.
(2) Video Channel State Control
Administrator decides whether to utilize video signal from selected channel in WebEye or not. If
user disables a channel with an external camera connecting to WebEye, WebEye does not show any
image from the channel. If user enables a channel without connecting an external camera to
WebEye, WebEye is interrupted and cannot transmit image properly (transmission speed of total
channels go down).
(3) Camera Color Type
It is to define every camera whether it is color or B/W camera. This si not to change its original
character but only to define the character and give information to WebEye.
(4) Video Signal Type
It is to define CCD module of WebEye and external CCD cameras between ‘NTSC’ and ‘PAL’.
(5) Camera Installation Angle
WebEye can always show images in right angle regardless its installation position. If
WebEye is located on the wall upside down, user can adjust image angel by
selecting ’90 deg.’ or ‘270 deg.’
39
WebEye E10/E104 User’s Guide
(5) Advanced Configuration
Calibration Parameters
Administrator manipulates screen
settings by adjusting brightness,
contrast, hue, saturation, horizontal
line shift, and vertical line shift from
the menu. With ‘Video Gain’ menu,
you may optimize the image without
adjusting each value of other menus.
However ‘Video Gain’ and ‘Vertical
Line Shift’ are not supported
currently. They are to be supported in
near future.
Caption Display Options
Administrator may configure caption
on real time image with display
options such as color and contents.
Caption is to be made of time
information, channel information, and
additional explanation (user defined
string).
Visual Setting Parameters
Administrator may configure QBOX and image quality level with aid of real time image. By
placing the mouse curse on real time image and clicking the left button, you may view pop-up
menus.
• QBOX Parameters : Administrator sets QBOX area with a mouse to ‘click and drag’.
Selected area shows in ‘Left Top Placement’ and ‘Right Bottom Placement’ panels in figures.
With ‘Ambient Level’ menu, Administrator may set quality level of unfocused area in the
image (out of the focused range). There are 5 levels. Administrator may set level 5(Darker) to
make unfocused area dark and get the transmission speed up.
• Image Quality Level: Administrator chooses image quality level from 0 to 9. If level 9 is
chosen, WebEye sends the finest image. However, transmission speed will be reduced because
of larger sized data. The image level inside the ‘QBOX’ is the same level as is selected in this
menu.
8) Application Configuration
This page is to configure e-mail and file sending function.
(1) Select Video Channel
It is to select a video channel for configuration. The four channels in WebEye E104 or two channels
in WebEye E10 are shown in the panel are same as seen in ‘Video Configuration’ page.
40
WebEye E10/E104 User’s Guide
(2) Recipient E-mail Address
This is to designate a person to
receive E-mail.
(3) Sender’s E-mail Address
This is to put a person’s e-mail
address that is considered as the
e-mail sender.
The e-mail sender can be a person
who should take care of the situation
when events occur. E-mail will be
delivered to a person who is defined
as a recipient in the blank of
‘E-Mail Recipient’. The person who
received e-mail can send a message
of countermove to a person who is
defined as an e-mail sender.
Actually, WebEye sends E-mail, but
it is no use sending E-mail back to
WebEye. So a person can be
designated to receive counter
e-mail.
Another important function of this menu is to avoid a problem that the e-mail is blocked from
e-mail server. Some e-mail servers don’t receive an e-mail that does not have its valid domain name
such as abc@abcdefg.com. It is because there are a lot of junk e-mails. So WebEye and other
devices that do not have their valid domain names or only have their IP addresses can’t send e-mails.
To avoid this problem, WebEye has the menu to put sender ’s e-mail address. The default value is
invalid, so administrator should change the address with valid one. Administrator may put one’s
e-mail address.
(4) Check E-Mail Options
Relay Mail Server: With the same problem of e-mail blocking, WebEye has a function to relay its
e-mail through an available e-mail server so that e-mail can have the relay server’s domain name.
After activating ‘User Relay Mail Server’ menu, you key in a server’s domain name such as
‘@abcdefg.com’. The e-mail server of default value is invalid, so don’t use the default value when
you have to use relay mail server function.
Content-Transfer-Type : It is to define e-mail format. E-mail servers support ‘Base64’ format in
common, but some servers not. In the case, you may select the format as ‘Quoted Printable’.
(5) E-Mail Event Configuration
Event source : Administrator should define with which event E-mail is to be delivered among MD
41
WebEye E10/E104 User’s Guide
(motion detection), sensor 1, sensor 2, sensor3, and sensor 4. If administrator clicks on sensor1,
e-mail is sent when the sensor1 detects events. (To utilize sensor input detection, a sensor should be
connected to WebEye.) If administrator clicks on periodic sending, e-mail is sent periodically every
preset time. The interval may be modified.
File name : With the images of MD and Sensor event, a file is named combining all options. And
with the image of periodic sending event, administrator may decide how to name image files among
three methods. Administrator names a file with data & time (DATETIME; E.g
IMG-CH00-2001030-223031.eye) or serial number (SEQNUM; E.g. IMG-CH00-SN1.eye). Also
administrator names the file with a fixed one (Manually assigned filename). The image file has its
extension of ‘eye’ so that the file is to be reproduced on Internet browser. With DATETIME or
SEQNUM format, WebEye automatically put its extension as eye. When a file name is set manually,
make sure to put its extension with ‘eye’ (e.g. manual.eye). If not, the file cannot be reproduced on
Internet browser or other program.
Image quality: Administrator may set image’s resolution that is delivered by e-mail. Resolution is
to be set among 90x60, 180x121, 360x243, 720x243, and 720x486. An image of 90 by 60 is of the
lowest resolution and the smallest size.
Check Points for E-mail Sending Problem
If you have problem in sending e-mail, check followings;
• If you have set DNS address properly in ‘System Configuration’ page.
• If you have set sender’s e-mail address properly in ‘Application Configuration’ page.
• If you have set e-mail type properly between ‘Base64’ and ‘Quoted Printable’.
(5) FTP directory configuration
Administrator assigns FTP server address, FTP user account, FTP user password, and FTP user path
to receive files when events occur.
(6) FTP event configuration
Administrator may set sending conditions, image resolution, and filename. Image resolution,
filename, and sending conditions setting methods for FTP are same as that of e-mail.
Transmission Performance of E-mail and FTP
• WebEye sends send once in five minutes at most when administrator configures
WebEye to send e-mail periodically. If there is no restriction in sending e-mail,
WebEye may cause a serious problem to the recipient’s mail server. However there is
no limit in sending e-mails under MD or sensor activated situation.
• With FTP function, there is no limit. And if the periodic sending menu is set as
zero(0), WebEye transmits files at its best performance .
42
WebEye E10/E104 User’s Guide
9) Pan/Tilt/Zoom Configuration
This page is to decide whether to
use pan/tilt/zoom control function
or not and select which serial port
to use.
(1) Video Channel Selection
Administrator selects a video
channel to utilize pan/tilt/zoom
mechanism. The four channels shown in the panel are same as seen in ‘Video Configuration’ page.
(2) Pan Tilt Function
Administrator defines whether to utilize pan/tilt control function or not.
(3) Zoom Function
Administrator defines whether to utilize zoom control function or not. With WebEye E10, internal
channel has fixed lens and doesn’t support zoom function, therefore the menu is not on the page.
(4) Pan Reverse Mode Function
This is to set command reverse direction against to right and left direction control arrows. This
function is useful when PT driver is installed upside down.
(5) Tilt Reverse Mode Function
This is to set command reverse direction against to up and down direction control arrows. This
function is useful when PT driver is installed upside down.
(6) Select Serial Port
It is to select a serial port between ‘Serial #1’ and ‘Serial #2’ with which a pan/tilt/zoom control
receiver is connected to WebEye. With WebEye E104, administrator should select proper serial port
between them. It is because the two ports have different interface each other.
WebEye E104
WebEye E104 has two pairs of interface pins. One pair is RS232C interface and
another is RS485 (Half -Duflex) interface. Among DB-15 pins located in the
rear of WebEye E104, pins of number 1 and number 2 (marked as RXD and
TXD) are RS232C interface and this pair is ‘Serial #1’. Pins of number 3 and number 4 (marked as
S+ and S-) are RS485 (Half-Duflex) interface and this pair is ‘Serial #2’.
WebEye E10
WebEye E10 also has 2 pairs of interface pins. Among DB-15 pins located in
the rear of WebEye E10, pins of number 1 and number 2 (marked as TX1 and
RX1) are RS232C interface and this pair is ‘Serial #1’. Number 3 and 4 pins
(marked as TX2 and RX2) are also RS232C interface and this pair is ‘Serial #2’.
43
WebEye E10/E104 User’s Guide
(7) Serial Port Base Address
This menu is to identify the base addresses between a channel of WebEye and pan/tilt/zoom control
receiver. Administrator may connect more than 2 pan/tilt/zoom control receivers to Serial #2
(RS485 (Half-Duflex)) with WebEye E104. In this case, administrator should configure control
receivers’ base addresses in the blank of each channel to control each pan/tilt/zoom mechanism
respectively for each channel. User may also utilize a control receiver for all 4 channels. In this case,
every pan/tilt driver or zoom lens of 4 channels is to move at same directions or degrees at the same
time. WebEye E10 has two pairs of serial ports, so that it is sufficient for all channels.
10) Serial Port Configuration
This page is to select a communication
protocol among listed ones or to set
control parameters manually for each
serial port.
(1) Serial Port Selection
Administrator selects a serial port to configure. WebEye E104 has two serial ports. Serial #1 is a
RS232C interface port, and Serial #2 is a RS485 (Half-Duflex) interface port. WebEye E10 has two
serial ports, and two of them are RS232C interface ports.
(2) Select Attached Device
PTZ protocols
Administrator selects a communication protocol that an attached external device
satisfies among already listed protocols. WebGate has listed protocols of Philips,
Pelco (P and D), Video Technical (VTP 4x), Sony (EVI-D3x), etc. Administrator
may utilize any pan/tilt mechanism that satisfies already listed protocols. Among
listed protocols, Philips, Pelco, Sensormatic and VT protocols are marked with
‘M’ and they are to be configured their control parameters such as ‘Baud Rate’,
‘Stop Bits’, ‘Data Bits’, and ‘Parity Check’ according to connected dome camera
settings.
Manual Setting
If your mechanism doesn’t use any of
already listed protocols, you may set
the protocol manually by selecting
‘Manual Setting’ and set parameters
through ‘Control Parameters’ and ‘PTZ
CMD’ menus. For detailed information,
please refer to following explanation.
Audio Device
This protocol is for WebEye A10,
which is an audio trans mission device connected to WebEye. For more detailed information on
WebEye A10, please refer to WebEye A10 User’s Guide.
44
WebEye E10/E104 User’s Guide
PTZ Command for Manual Script
1. Escape Characters
#
Special command
@
Hexadecimal character
%
Decimal character
^
Character
,
Break character
;
End of current packet
&
Special operation
2. Special command (Followed by #)
A
Address assigned by PTZ configuration
X
Acceleration rate selected by user
Sx
Checksum calculation method
x = 0 Sum of entire frame, size = 1byte
x = 1 Sum of entire frame, size = 2byte
x = 2 Sum of entire frame except first byte(sync), size = 1byte
x = 3 Sum of entire frame except first byte(STX) and last byte(ETX), size = 1byte
x = 4 Sum and one's complement of entire frame except first byte(STX) and last byte(ETX),
size = 1byte
x = 5 XOR sum of entire frame, size = 1byte
x = 6 XOR sum of entire frame, size = 2byte
x = 7 XOR sum of entire frame except first byte(sync), size = 1byte
x = 8 XOR sum of entire frame except first byte(STX) and last byte(ETX), size = 1byte
x = 9 XOR sum and one's complement of entire frame except first byte(STX) and last byte(ETX),
size = 1byte
3. Special Operation (Followed by &)
Sx
Delay about ( ([acceleration rate] + 1) * (100 * x) ) ms
x
0~4
4. Exceptions
Normal character following Escape Sequence, must use break character for identify end of sequence
n Some protocols are not to be made command script with above method. It is because they have
another method of checksum calculation. If your protocol does not use above checksum calculation
method, please inquire WebGate Inc. through its Internet homepage. In the case, it is necessary to
send the protocol together.
45
WebEye E10/E104 User’s Guide
11) Digital I/O Configuration
This page is to configure digital
input/output states and control script.
WebEye sends e-mails or/and files
when connected external sensors detect
events.
(1) Device Type for Input Port 1 & 2
Administrator defines active state of 2
digital devices connected to two input
ports such as infrared sensors. If you connect normal open type device to input port, you should
select ‘NO (Normal Open)’. With normal close type device, you should select ‘NC (Normal
Close)’.
(2) Current State for Input Port 1 and 2:
WebEye shows current states of the 2 digital devices connected to 2 input ports. In the status panel,
active state or de-active state message shows. ‘De-Active State’ means that connected device didn’t
detect any event when ‘Apply button’ is clicked. Though this message is not updated until you click
‘Confirm’ button again, WebEye keeps on receiving status information from the connected device.
(3) Active State for Output Prot 1
Administrator defines active state of a digital device to be connected to the output ports such as an
electronic locker or a switch. Active states of digital devices may differ depending on items or
models (select between ‘Open’ or ‘Close’)
(4) Current State for Output Port 1
According to active state definition, WebEye shows current states of the digital device connected to
an output port. Its state is defined at ‘Active State for Output Port’ menu.
(5) Status Control for Output Port1
Administrator controls an external device that is connected to the output port. After defining active
state of the device at ‘Active State for Output Port 1’, Administrator controls the device to act or not
with this menu.
(6) Active Condition and Duration for Output Port1
Administrator defines active conditions for an external device such as an electric light that is
connected to the output port. After defining active state and controlling status of the device,
administrator defines active conditions among internal S/W motion detection (MD Event) and two
external sensors (SID1 & SID2 Event). And ‘Active Duration’ menu is to set the period of time to
activate the external device after detecting event. If the event lasts long, WebEye activate the device
for preset time after the last event detection.
46
WebEye E10/E104 User’s Guide
12) Alarm Configuration
This page is to set conditions for
recording images during event
situation, so that WebEye sends the
images through e-mail or FTP.
(1) Motion Detection Threshold
Administrator sets threshold for
motion detection function. Threshold
‘0’ is the most sensitive state and ‘900’ is the dullest state.
(2) Alarm Parameters for E-mail / FTP Application
Administrator defines conditions for recording image to WebEye, if WebEye detect events through
motion detection unction (MD Event) or external devices (SID1 and SID2). WebEye can record 2
frames for 2 seconds before the event and 2 frames for 2 seconds after the event as well as 1 frame
at the moment of event. Its maximum recording rate is 1 frame per second and the total fames are
maximum 5. WebEye records the images and send them through e-mail or FTP according to preset
conditions on ‘Application Configuration’ page and ‘Alarm Configuration’ page. If event lasts long,
WebEye sends images not duplicating regardless overlapped time setting. The resolution of the
image is fixed as 360x243.
13) User Custom Configuration
This page is to customize TCP ports
of data transmission and default
viewer composition.
(1) Web Server TCP Port
Administrator assigns a web server
TCP port through which people can
access WebEye and WebEye sends
data. 80t h port is assigned default value.
(2) Video Server TCP Port
Administrator assigns a video server TCP port through which WebEye transmits images to users.
8080t h port is assigned as default value.
(3) Select Main Page
Administrator assigns a viewer as a main page that appears first when users access Webeye.
Administrator can select a viewer among 7 different ones such as ‘Default Simple Viewer’, ‘Default
Multi Viewer ’, ‘Simple Single Viewer’, ‘Simple Multi Viewer ’, ‘Normal Single Viewer’, ‘Normal
Multi Viewer ’, and ‘Server Push Viewer’. Single Viewer is to show image from Ch#0(Internal) and
Multi Viewer is to show all images from 4 channels (WebEye E104) or 2 channels (WebEye E10).
47
WebEye E10/E104 User’s Guide
(4) Default Viewer Editing
‘Default Viewer’ is designed for users to edit easily. Editable parts are as bellows.
• Main Title : It is to change the main title that is written on the bottom of the default viewer.
• Logo Image Source URL: Administrator may assign a URL of a certain web site from which
default viewer gets a logo. The space to put a log locates on the left top of the viewer.
• Logo Image Link URL : Administrator may link the logo with a certain web page. User can
link the logo with a company homepage or a personal one.
• Background Color and Foreground Color: Ground color of default viewer can be changed.
Administrator may set the color with RGB value.
When the changed settings are to be affected?
You have to click ‘Apply’ button at every administration page, if you want to apply
changed settings onto your WebEye.
14) Goto Viewer Page
This menu is to return to real time image viewer page from administration page.
48
WebEye E10/E104 User’s Guide
VIII. Convenient Functions of Mouse (Pop-up menu)
A small window of 5 menus appears when you click the right button of
the mouse. However only a certain users who are permitted can utilize
the functions such as ‘Image Info’, ‘Quality Box’, ‘Focus Sensitivity’,
and ‘Image Quality’. And the results of the four functions are to be
affected in every image that is transmitted to all users. ‘Save File As’
menu is permitted to any user. (For detailed information, refer to ‘User
account management’ in Chapter VII).
1. Image Info
You may decide the color (black or white) of the information that is shown on the
left top of the image. And you may leave out the information. A user who has
‘Video control’ right may utilize this menu.
2. Quality Box
This is to set a certain area clear and remained area dull. You can overcome
insufficient network bandwidth with this function, because the file size is
reduced with unfocused area. Quality Box is to be set like under written
description.
• Choose ‘New QBOX’ button.
• Place mouse cursor on a certaion point of real time image where to start QBOX.
• Click and drag the mouse point.
You can also re-use previous QBOX area to focus again
by clicking ‘Enable QBOX’. ‘Disable QBOX’ is to finish.
The image activated Focusing Area function is seen in the
right. The image quality of outer area of QBOX is to be set
with ‘Ambient Level’ menu. The level is from 1 to 5. If
you select ‘Level 1’, the quality is similar to focused area.
And if you select ‘Level 5’, the unfocused area is shown
dark. A user who has ‘Video control’ right may utilize this
menu.
3. Focus sensitivity
You may configure movement degree of zoom mechanism. The sensitivity is from
Level 0 to Level 9. By selecting ‘Level 9’, user zooms in or out at the largest
degree. A user who has ‘PTZ control’ right may utilize this menu.
4. Image quality
It is to set image quality. The image quality is from Level 0 to Level 9. If user
chooses the ‘Level 9’, WebEye sends the finest image. However, transmission
frame rate will be reduced because of large sized data. If user chooses ‘Level 0’,
49
WebEye E10/E104 User’s Guide
WebEye sends dullest image but fast. A user who has ‘Video control’ right may utilize this menu.
5. Save File As
It is to save a frame of still image as an electric file. A still image can be saved as bitmap (*.bmp)
file or Wavelet format file (*.eye). Wavelet formatted image file is to be reproduced on Internet
browsers such as Netscape Navigator or Internet Explorer as long as the PC is installed Active-X or
Plug-in program. The very image that is shown at the moment when you click the menu is saved.
50
WebEye E10/E104 User’s Guide
IX. Adjusting Focus.
1. WebEye E104
(1) Adjust focus of WebEye E104 by
turning the focus ring in the front of
8mm lens.
Tiny screw
(2) If lens does not turn, loosen the three
tiny screws on the mount.
Tiny s crew
(3) Setting the lens at the middle range,
focus by turning the lens itself.
Tiny s crew
(4) Once focus is achieved, fasten the
three tiny screws tightly.
2. WebEye E10
Turn the lens right or left to adjust focus .
Turn left or right the lens
with this part
51
WebEye E10/E104 User’s Guide
(Appendix 1)
Detailed Specifications of WebEye E10
1. General
Hardware
CPU
Flash memory
RAM
OS
Video Channel
Image Resolution
32bit RISC Embedded processor
8Mbyte
16Mbyte
Embedded Linux
NTSC or PAL video format are supported
1Ch. Internal Video Input (Internal Camera)
1Ch. External Video Input/Output (Optional BNC Connector)
720X486, 720X243, 360X243, 180X121, 90X60
Image Compression
Algorithm
Wavelet
Rate
10:1 ~200:1
Performance
Transfer Rate
Maximum 123fps (With 3KB image)
Decoding Rate
2 ~ 30fps
Local Compression rate
Max 30fps
Security
Password Based User Authentication
IP-filtering (Secure Mode)
Image Encryption
Alarms and I/O
Motion detection
Sends e-mail automatically
Sends the image files through FTP automatically
Software-controlled 2-alarm input
MISC . function
High quality image area setting
Image quality control (10 Levels)
Periodic sending of images through E-Mail or FTP
Gray/Progressive/Single-Shot Mode
User customized home page publishing supported by FTP
Power Supply
DC 5V, 1.5A via external power supply
2. CCD Module
Horizontal resolution 330 TV lines
Pick-up device
1/4 inch interlined CCD
Scanning System
525 lines interlaced (NTSC)
625 lines interlaced (PAL)
Synchronization
Internal
Output Signal
Standard composite signal
1 Vpp composite video into 75 ohms
52
WebEye E10/E104 User’s Guide
Light sensitivity
30 IRE
Electronic Iris
5 Lux(Scene)
1/60~1/96,000(NTSC)
1/50~1/96,00 0(PAL)
Signal to Noise Ratio 46dB or more (AGC off)
AGC
ON (0-15dB Max)
Input Voltage
5V DC
Power Consumption 160mA or less
Ambient Temperature
Operation
-10C (14 F) to +50C (122 F)
In storage
-20C (-4 F) to +65C (149 F)
Relative Humidity
Operation
Under 90% Non-condensing
In storage
Under 95% Non-condensing
Weight
13 g
Standard Lens
Fixed, F2.0, f=3.8mm, Horizontal view angle 53°
3. Network
Browser
MS Internet Explorer V. 5.0 or higher
Netscape V. 4.7 or higher
JAVA Applet for non PC User (MAC or Unix)
10 Based-T Ethernet (RJ -45)
Connector
Installation
Assign IP address using setup program or ARP, RARP protocol
Protocols supported TCP/IP, HTTP, ARP, RARP, ICMP, DHCP, FTP, SMTP and PPPoE
S/W Update
Flash memory allows central remote software updates over network
using FTP or private “WebyeUpgrade” program.
Management
Configuration is achieved by private setup program and Web server
built in administration page.
4. Mechanical
Dimension
Weight
H x W x L = 45mm x 92mm x 146mm
187g, without power supply
5. Environmental
(*) This data is a target specification.
Temperature *
Operating
Non-Operating
Under Shipment
-5°C (23 F) ~ +40 °C (104 F), Gradient 15°C (59 F)/Hr max
-20°C (-4 F) ~ +60°C (140 F), Gradient 15 °C (59 F)/Hr max
-40°C (-40 F) ~ +70°C (158 F), Gradient 30°C (86 F)/Hr max
(Packed in WebGate’s original shipping package)
53
WebEye E10/E104 User’s Guide
Humidity *
Operating
Non-Operating
Under Shipment
Vibration *
Acceleration
Frequency
Sweep Time
Shock *
EMC Adaptability
8% ~ 90% R.H. No condensation
8% ~ 90% R.H. No condensation
5% ~ 90% R.H.
(Packed in WebGate’s original shipping package)
1.2G
10Hz ~ 60Hz
1 OCT/Min
10 G (10msec half sine wave Repeated twice maximum/sec)
EN50082-1: 1992
IEC 801-2: 1991
IEC 801-3
IEC 801-4
EN55022/1994, +A1: 1995, +A2: 1997 Class-A
EN61000-3-2: 1995, +A1: 1998, +A2: 1998
EN61000-3-3: 1995
VCCI
FCC Class A
6. Compatible external devices and software
PTZ control
Sensor input
2 Ch. RS-232 (15pin DSUB connector)
15-pin D-SUB connector is available
2 auxiliary inputs are supported, made of ‘Opto coupler’
Opto coupler stands with 3-5V and 10-20mA(Appendix 2)
54
WebEye E10/E104 User’s Guide
(Appendix 2)
Detailed Specifications of WebEye E104
1. General
Hardware
CPU
Flash memory
RAM
OS
Video Channel
Image Resolution
Control
Image Compression
Algorithm
Rate
32bit RISC Embedded processor
8Mbyte
16Mbyte
Embedded Linux
NTSC or PAL video format are supported
1Ch. Internal Video Input (Internal Camera)
4Ch. External Video Input/Output (BNC Connector)
720X486, 720X243, 360X243, 180X121, 90X60
Wavelet
10:1 ~200:1
Performance
Transfer Rate
Max up to 123fps (With 3KB image)
Decoding Rate
2 ~ 30fps
Local Compression Rate
Max 30fps
Security
Password Based User Authenticat ion
IP-filtering (Secure Mode)
Image Encryption
Alarms and I/O
Motion detection
Sends e-mail automatically
Sends the image files through FTP automatically
Software-controlled 2 alarm input
MISC . function
High quality image area setting
Image quality control (10 Levels)
Periodic sending of images through E-Mail, FTP
Gray/Progressive/Single-Shot Mode
User customized home page publishing supported by FTP
Power Supply
DC 12V, 1.0A via external power supply
2. CCD Camera
Horizontal Resolution 450 TV lines
Pick-up Device
1/3 inch interline CCD
Scanning System
525 lines interlaced (NTSC)
625 lines interlaced (PAL)
Synchronization
Internal
Output Signal
Standard composite signal
55
WebEye E10/E104 User’s Guide
1 Vpp composite video into 75 ohms
Light sensitivit y
30 IRE
Electronic Iris
3 Lux(Scene)
1/60~1/100,000(NTSC)
1/50~1/100,000(PAL)
Signal to Noise Ratio 46dB or more (AGC off)
AGC
ON (0-15dB Max)
Input Voltage
12V DC
Power Consumption 2.4A or less
Ambient Temperature
Operation
-10C (14 F) to +55C (131 F)
In storage
-20C (-4 F) to +70C (158 F)
Relative Humidity
Operation
Under 90% Non-condensing
In storage
Under 95% Non-condensing
Weight
30 g
Standard Lens
C mount, Aperture: Fixed F1.3 (F1.8)
Focal length: Fixed 8mm (6mm)
3. Network
Browser
MS Internet Explorer V. 5.0 or later
Netscape V. 4.7 or later
JAVA Applet for non PC User (MAC or Unix)
Connector
10 Based-T Ethernet (RJ -45)
Installation
Assign IP address using setup program or ARP, RARP protocol
Protocols Supported TCP/IP, HTTP, ARP, RARP, ICMP, DHCP, FTP, SMTP and PPPoE
S/W Update
Flash memory allows central remote software updates over the network
using FTP or private 'WebEyeUpgrade'
Management
Configuration is achieved by private setup program And Web server
built in administration page.
4. Mechanical
Dimension
Weight
H x W x L = 74mm x 95mm x 185mm
650g(1.43lb), without Power supply
5. Environmental
(*) This data is a target specification.
Temperature *
Operating
Non-Operating
Under Shipment
-5°C (23 F) ~ +45 °C (113 F), Gradient 15°C/Hr max
-20°C (-4 F) ~ +65°C (149 F), Gradient 15 °C /Hr max
-40°C (-40 F) ~ +70 °C (158 F), Gradient 30°C/Hr max
(Packed in WebGate’s original shipping package)
56
WebEye E10/E104 User’s Guide
Humidity *
Operating
Non-Operating
Under Shipment
Vibration *
Acceleration
Frequency
Sweep Time
Shock *
EMC Adaptability
8% ~ 90% R.H. No condensation
8% ~ 90% R.H. No condensation
5% ~ 90% R.H.
(Packed in WebGate’s original shipping package)
1.2G
10Hz ~ 60Hz
1 OCT/Min
20 G (10msec half sine wave repeated twice maximum/sec)
EN50082-1: 1992
IEC 801-2: 1991
IEC 801-3
IEC 801-4
EN55022/1994, +A1: 1995, +A2: 1997 Class-A
EN61000-3-2: 1995, +A1: 1998, +A2: 1998
EN61000-3-3: 1995
VCCI
FCC Class A
6. Compatible External Devices and Software
PTZ control
Sensor Input
Sensor Output
1 Ch. RS-232, 1Ch. RS-485 (15pin DSUB connector)
Multiple PTZ devices are supported via RS-485
2 auxiliary inputs are supported, made of ‘Opto coupler’
Opto coupler stands with 3-12V and 10-20mA
Solid state relay
57
WebEye E10/E104 User’s Guide
(Appendix 3)
Frequently Asked Questions
1. About WebEye's Feature
• Q: What is WebEye?
A: The WebEye is a flash memory, and many other features. No other hardware is cameratype
server with an integrated Internet server, image compression device, built in CCD, necessary
for use. The WebEye connects directly to a network and provides real time images over
networks and the Internet. Simply provide power and connect LAN cable to the WebEye.
• Q: What preparations are needed to install?
A: Provide power and connect network cable. Insert the WebEyeSetup disk, drag the WebEye
Setup icon from the pop-up window onto the desktop, double-click the icon.
• Q: Which algorithm is used to compress digital images?
A: WebEye utilizes the Wavelet image compression device and the Linux operating system.
Wavelet and Linux enable WebEye to transfer high quality images faster and with a greater
degree of reliability than standard JPEG systems.
• Q: What is the difference between Wavelet algorithm and JPEG in compressing digital images?
A: Wavelet is more efficient than JPEG by 30-300%. The higher efficiency of Wavelet comes
from its encoding method. Wavelet uses the DWT (Discrete Wavelet Transform) algorithm,
while JPEG uses DCT (Discrete Cosine Transform). Due to its efficiency, Wavelet will be
adopted as the standard in digital image compressing with the introduction of JPEG2000.
Since Wavelet is not yet standardized, it requires the installation of a Plug-in or
Active-Xcontrol for standard Web browsers such as Netscape and IE-Explore. The size of
the Plug-in or Active-X control is 3 MB. 3MB needs quite a long time to download, so
Wavelet is not widely used. However, Web Gate Inc. has developed a Plug-in/Active-X
control of 300KB for faster, more efficient download time.
• Q: Can WebEye support more than one user with different resolutions at the same time?
A: WebEye can support up to 100 users with different resolutions at the same time.Moreover,
WebEye has progressive mode and gray mode to support low speed network line users. A
user can monitor full resolution (720 X 486) color images while another user sees half
resolution (360 X 243) B/W images.
• Q: What is maximum transmission speed?
A: WebEye compresses and transmits 30 frames per second (fps) on 10 base-T Network.
However this speed is not equal for every user because transmission speed depends on the
performance of individual PCs and network bandwidth. 30 fps refers to the user-end or
receiving side of the transmission. WebEye can send more than 30 fps total to several users.
For example, if 5 users are receiving 10 fps, WebEye is sending 50 fps. When WebEye is
connected to a 10 base-T network, it can transmit up to 123 fps of 3KB image files.
58
WebEye E10/E104 User’s Guide
• Q: What is maximum number of users to access WebEye at the same time?
A: The maximum number of simultaneous users is 100. WebEye could support more than 100,
but overall transmission speed would be very slow. To ensure the most effective
transmission speed, WebEye has been programmed to accept no more than 100 users.
When 100 users are logged on to WebEye, the transmission speed is approximately 1 frame
per 10 seconds.
• Q: Does WebEye contain Pan/Tilt/Zoom function?
A: WebEye has pan/tilt/zoom controlling function within its firmware. Pan/tilt devices and
zoom lenses can be connected to the DB-15 port in the rear of WebEye. The protocols for
several P/T/Z devices are already installed in WebEye. They can be selected from the pull
down menu of the “Attached Device” section of the “Serial Port Configuration” menu in the
Administrator’s homepage. (For more information, refer to pg. 39, “Serial Port
Configuration” of the WebEye User’s Manual)
• Q: Is there any limitations in setting ID or password?
A: IDs and passwords can be no longer than nine (9) characters long. The ID/password
program is case-sensitive, which means it distinguishes between upper- and lower- case
letters. For example “GUEST1” is different from “guest1.”
2. About Installing and Running WebEye.
• Q: What network line can be used with WebEye?
A: All network lines (except telephone lines) can be used, although telephone lines may be
used through PCs to connect to WebEyes remotely. Network lines such as xDSL, cable
modem, and ISDN that use dynamic IP addresses require a different installation process
than a dedicated line that has a fixed IP address. (For more information, refer to pg. 33,
“Dynamic IP Registration” of the WebEye User’s Manual)
• Q: What is the maximum extension range of network lines?
A: UTP cable that is used for LAN can be extended up to 100 meters without bridging.
However, existing UTP cable can be extended up to 240 meters without bridging.
• Q: Can ordinary telephone lines be used for WebEye?
A: Telephone lines can be used for WebEye, but a telephone modem router must be equipped.
Web Gate Inc. will provide a telephone modem router in the near feature, but using
telephone lines is not recommended because transmission speed is very low.
• Q: Is a special rack or case needed when WebEye is installed outdoors?
A: WebEye is not weatherproof. If WebEye is to be used outdoors, it needs to be equipped with
a weatherproof case.
59
WebEye E10/E104 User’s Guide
• Q: If the network consists of one permanent IP address and several private IP addresses, can
WebEye be connected to the network with a private IP address?
A: WebEye can be assigned a private IP address on a network with a permanent IP address. If
the network is a Class C network (255.255.255.XXX), then WebEye may be assigned any
available number in the last “room” (represented by XXX). However, since WebEye is a
web server, it can be designated as a local server. Any device on a LAN can be designated
as the local server through the router. Designating WebEye as the local server will make it
easier for people outside the LAN to view real-time images from WebEye.
• Q: If the network consists of only private IP addresses, can WebEye be connected at the
network?
A: WebEye can be connected to LAN having only private IP addresses, but only people on the
local network can access WebEye. Networks with narrow bandwidth may not be able to
support several WebEyes connected simultaneously.
• Q: If a firewall is on the network, can WebEye be installed and work?
A: If there is a firewall on the network, port 80 is open for ordinary data communication.
However, since WebEye transmits image data, the default port 8080 is also required.
Therefore, it is necessary to open port 8080 of the network for remote users to access
WebEye. Ports may be configured at the “User Custom Configuration” section of the
Administrator’s homepage.
The “Server Push Viewer” enables WebEye to send images through the 80t h port. Another
method is to change the image transmission port from 8080 t h port to any port granted by the
firewall.
• Q: How can a user see the image sent from WebEye when us ing Netscape?
A: If a user wants to use a Netscape browser, the WebEye Plug-in program must be installed.
The procedure for the Plug-in setup is below:
-. Access WebEye using assigned IP address on the Netscape such as http://168.192.1.1/
-. Setup the WebEye Plug-in using the Netscape Smart Update
WebEye Plug-in for Netscape is saved on the WebEye itself. When a user connects to
WebEye for the first time or has an old version of Plug-in, download the current version by
clicking "Download WebEye Plug In Now!"
• Q: How can a user see the images sent from WebEye us ing Internet Explorer?
A: If a user wants to see the real-time images of WebEye using Internet Explorer browser,
install WebEye Plug-in and Active-X control. The Plug-in is used in the server-push viewer
and Active-X control is used in the live image viewer.
60
WebEye E10/E104 User’s Guide
If the Active-X control is not installed in your system or is an old version, the installation of
Active-X control will occur automatically. Just click “Yes” when the pop-up window
appears. Internet Explorer browser 4.0/5.0 or above is recommended.
• Q: What should be done if Active-X Control is installed incorrectly?
A: If no image appears after the installation of the Active-X Control program, it may be
removed and re-installed. To remove Active-X on Windows98 OS, search the
(C:\windows\Downloaded Program Files) directory. For Windows NT or 2000, search the
(C:\winnt\Downloaded Program Files) directory. If problems still persist after removal and
re-installation, contact Web Gate Inc. (www.webgateinc.com ) or e-mail: webeye@webgateinc.com
• Q: What should be done if runtime errors of the Plug-in/Active-X control occur?
A1: If the message box-- “Mismatched Version” appears, do the following:
Remove and Re-install the Plug-in or Active-X control contained in the WebEye.
A2: If the message box-- “WebEye client initializing has failed” appears, do the follow ing:
This message appears because the user's PC does not have Winsock2 library.
Winsock2 library for Windows95/98 can be downloaded from public sites. After
Winsock2 is downloaded, install it into the system and re-run Web browser.
• Q: Video is not seen in WebEye's homepage. What is the problem?
A1: If the video from WebEye's inner CCD module does not appear, the problem could be one
of two things: “CH 1 (external)” has been designated as the video source and there is no
external device connected; or the CCD module has not been activated. If a “Channel
Disabled” message appears, check the “Video Channel Selection for CAM#1” setting under
“System Configuration” on the Administrator’s homepage. The attached cam should be
Internal (CH#0). If the channel selection is set at internal (CH#0) but the “Channel
Disabled” message still appears, check “Video State Control” under “Video Configuration.”
The video state control should be “Enabled.” If problem persists, contact Web Gate Inc.
A2: If the videos from external CCD cameras do not appear, the problem could be because
external CCD channels are not activated. To activate channels, go to the “Video
Configuration” page and select the desired channel. Then press “Enable” at the “Video
Channel State Control” line. If the external camera is enabled but images still do not appear,
check the BNC connection.
• Q: Which Pan/Tilt/Zoom mechanism can be installed to WebEye?
A: WebEye already has the protocols for the following Pan/Tilt/Zoom devices: Philips, Pelco
(D and P), Sony (EBI -D3x), Surveyor (PT360), Sungjin, Unimo, and Saerim. The
administrator may also set command parameters manually. In addition, Web Gate Inc. is in
the process of expanding the number of stored protocols for better convenience. For zoom
lenses, the E10 cannot be equipped with a zoom lens, but it can support an external camera
61
WebEye E10/E104 User’s Guide
with a zoom lens. (For more information, refer to pg. 38, “Pan/Tilt/Zoom Configuration” of
the WebEye User’s Manual)
• Q: It is impossible to assign IP address to WebEye with Ping command. What is the problem?
A: If WebEye is connected to a local network, the Ping command can be used to assign an IP
address from a local PC or notebook computer. If the Ping command does not work, check
the green LED on the back of WebEye. It should blink about once every two seconds. If it
does not, check the network line and the LAN port. If the LED blinks normally, check the IP
address of the PC. If the IP of the PC is different than the one being assigned to WebEye,
the Ping command will not work. For a Class-C network, the first three “rooms” must have
the same numbers. The last room identifies individual devices. If the first three rooms of a
Class-C network differ between PC and WebEye, then they are not on the same network.
(For more detailed information, refer to Appendix 4 in the WebEye User’s Guide.)
• Q: There is some problem accessing WebEye. Sometimes I can access WebEye and sometimes
not. How can it be solved?
A: This problem mostly occurs on Cable Modem, ISDN, and xDSL lines that use modems or
routers. The modems or routers will automatically disconnect lines that are not active.
Generally, a modem or a router is set to disconnect from a network 3-5 minutes after
WebEye stops using lines. ISPs set this condition to prevent their lines from being
overloaded with inactive signals. To overcome this problem, set the “Dynamic IP
Registration Interval” at approximately one minute. Although this feature is intended for
Dynamic IPs, it can also be used here to send active signals to the router and maintain a
connection. It is important to set the dynamic IP registration interval shorter than the
connection duration of a modem to maintain a continuous connection.
• Q: I can't see the images in WebEye Java Applet view page. I am using Netscape browser on
Macintosh computer. What should I do?
A: Install MRJ (Macintosh Runtime for Java) and MRJ Plugin for Netscape browser. Please,
take the following steps for installation.
1. Go to http://www.apple.com/java/ and download MRJ v2.2.4.
2. Delete the existing MRJ package's folder ("root/Apple Extras/Mac OS Runtime
for Java") if it exists.
3. Install MRJ package downloaded from step 1. (Refer to the apple's java site for
detail
information)
4. Go to http://www.mozilla.org/oji/MRJPlugin.html and download Netscape MRJ
Plugin.
5. Refer to the installation procedure in the mozilla's web site.
6. Try to see the images in WebEye's Java Applet view page after installing Netscape's
MRJ Plugin.
62
WebEye E10/E104 User’s Guide
• Q: I can't automatically download Plugin/ActiveX Control for WebEye.
A: Both the Plugin program and Active-X control are designed to be downloaded and installed
automatically. However, situations occasionally arise which prohibit this from happening. If
the Netscape browser can’t support the SmartUpdat e function, the automatic installation
after download may fail. For Active-X Control, if Internet Explorer is an earlier version than
v4.0 or the registry information of the system is corrupted, the automatic download and
installation may fail. If problems occur with automatic download, please try a manual
download:
1. Download the installation program.
2. Execute the "webcameracontrols.exe" file.
• Q: I can't run the setup program delivered with WebEye Product.
A: The setup program is an MFC-based windows program. If MFC42.DLL is not installed or is
an incompat ible version, the setup program may fail to start. If the program shows a
message like “...MFC42.DLL...not found...,” MFC42.DLL must be installed. The
installation procedure is as follows:
1. Download MFC42.CAB.
2. Unzip the .cab file into your temporary folder.
3. Execute the "mfc42.exe".
• Q: From the setup program, when I select one of the WebEyes in the list box and press "Change
IP Address" button, the setup program returns a "No Response" message.
A: The PC may be using the “Obtain an IP address automatically” option in Windows->Control
Panel->Network->Local Area Connection->Properties ->Internet Protocol->Properties. Use
the “Use the following IP address” option. Once the option has been changed, the setup
program should work. If not, contact Web Gate Inc.
• Q: About the setup program, when I select one of the WebEyes in the list box and press
"Start Configuration" or "Rebooting" button, the setup program returns the "No Response"
message.
A: If the IP address of the WebEye you selected is not in the subnet of your computer, the “No
Response” message will appear. Make sure the WebEye's IP address is in the same subnet as
the PC by using the “Change IP address” button.
63
WebEye E10/E104 User’s Guide
(Appendix 4)
Utilizing IP Addresses on Local Network
1. Introduction
Increasingly, most of our businesses are done via Internet. IP addresses are what we utilize to
access to the Internet.
Currently, IP addresses are limited. There are 5 classes’ of networks, and each network contains IP
addresses. A network can only hold a limited number of IP addresses. The number of IP addresses
depends on the network class. The 5 classes are labeled “A” through “E,” with the most common
one being the “C” class network.
2. IP Construction and Network Class
1) IP Construction
xxx
xxx
xxx
X1
X2
X3
xxx
X4
(xxx: 0 – 255)
e.g. 192.168.1.1
2) Network Class
A Class : A network that contains IP addresses from 0 to 127 at room ‘X1’.
Network ID: X1
Host ID: X2, X3, X4
There are 128 A-class networks in the world.
B class: A network that contains IP addresses from 127 to 191 at room ‘X1’.
Network ID: X1, X2
Host ID: X3, X4
There are 65,534 B-class networks in the world.
C class: A network that contains IP addresses from 192 to 223 at room ‘X1’.
Network ID: X1, X2, X3
Host ID: X4
The most common network in the world; there are 2,097,152 C-class networks in the world.
D class: A network that contains IP addresses from 224 to 239 at room ‘X1’. D-class networks are
used for multicasting, and are not allowed for common use.
E class: A network that contains IP addresses from 240 to 225 at room ‘X1’. E-class networks are
reserved.
64
WebEye E10/E104 User’s Guide
3. C class Network
1) Features of Addresses
IP address : The three digit number in room ‘X4’ is for the Host ID. The numbers range from 0 to
255. Among the numbers, 0 is used for Network ID, 1 is used for Router IP (Gateway address) and
255 is used for Broadcast address. The numbers from 2 to 244 are IP addresses that can be assigned
to WebEye, i-Rec Cam104, PC etc.
Network ID: Identifies a network. Generally the first number assigned is Network ID.
Gateway address: The IP address of the router for connecting Internet and local network. Remote
users can access local network over Internet through the gateway (router). Generally the second
number is assigned as Gateway address.
Broadcast address: Broadcasts to all devices that are connected on local network. Broadcast
address is a destination for broadcasting. All devices connected on local network have the same
Broadcast address.
Subnet Mask: Divides a local network into two remote networks. Subnet mask shows the IP
quantity in a certain network. The numbers that can be used as subnet mask are limited (0, 4, 8, 16,
32, 64, 128)
2) Network configuration
(1) To use as one network
Network ID: xxx.xxx.xxx.0
Gateway Address: xxx.xxx.xxx.1
Subnet Mask: 255.255.255.0
Broadcast Address: xxx.xxx.xxx.255
IP Addresses: xxx.xxx.xxx.2 – xxx.xxx.xxx.254
(2) To use as two sub-networks (1/2 + 1/2)
Sub-Network ID: xxx.xxx.xxx.0
Gateway Address: xxx.xxx.xxx.1
Subnet Mask: 255.255.255.128
Broadcast Address: xxx.xxx.xxx.127
IP Addresses: xxx.xxx.xxx.2 – xxx.xxx.xxx.126
Sub-Network ID: xxx.xxx.xxx.128
Gateway Address: xxx.xxx.xxx.129
Subnet Mask: 255.255.255.128
Broadcast Address: xxx.xxx.xxx.255
IP Addresses: xxx.xxx.xxx.130 – xxx.xxx.xxx.254
65
WebEye E10/E104 User’s Guide
(3) To use as three sub-networks (1/4 + 1/4 + 1/2)
Sub-Network ID: xxx.xxx.xxx.0
Gateway Address: xxx.xxx.xxx.1
Subnet Mask: 255.255.255.192
Broadcast Address: xxx.xxx.xxx.63
IP Addresses: xxx.xxx.xxx.2 – xxx.xxx.xxx.62
Sub-Network ID: xxx.xxx.xxx.64
Gateway Address: xxx.xxx.xxx.65
Subnet Mask: 255.255.255.192
Broadcast Address: xxx.xxx.xxx.127
IP Addresses: xxx.xxx.xxx.66 – xxx.xxx.xxx.126
Sub-Network ID: xxx.xxx.xxx.128
Gateway Address: xxx.xxx.xxx.129
Subnet Mask: 255.255.255.128
Broadcast Address: xxx.xxx.xxx.255
IP Addresses: xxx.xxx.xxx.130 – xxx.xxx.xxx.254
(4) To use as four sub-networks (1/4 + 1/4 + 1/4 + 1/4)
Sub-Network ID: xxx.xxx.xxx.0
Gateway Address: xxx.xxx.xxx.1
Subnet Mask: 255.255.255.192
Broadcast Address: xxx.xxx.xxx.63
IP Addresses: xxx.xxx.xxx.2 – xxx.xxx.xxx.62
Sub-Network ID: xxx.xxx.xxx.64
Gateway Address: xxx.xxx.xxx.65
Subnet Mask: 255.255.255.192
Broadcast Address: xxx.xxx.xxx.127
IP Addresses: xxx.xxx.xxx.66 – xxx.xxx.xxx.126
Sub-Network ID: xxx.xxx.xxx.128
Gateway Address: xxx.xxx.xxx.129
Subnet Mask: 255.255.255.192
Broadcast Address: xxx.xxx.xxx.191
IP Addresses: xxx.xxx.xxx.130 – xxx.xxx.xxx.190
Sub-Network ID: xxx.xxx.xxx.192
Gateway Address: xxx.xxx.xxx.193
Subnet Mask: 255.255.255.192
Broadcast Address: xxx.xxx.xxx.255
IP Addresses: xxx.xxx.xxx.194 – xxx.xxx.xxx.254
66
WebEye E10/E104 User’s Guide
(Appendix 5)
Upgrading WebEye Firmware
Warning
This process is to update WebEye with a new firmware.
Make sure to complete the whole process, since you begin the process. When the
process is completed, ‘User Image Upgrade is complete’ message appears. During the
process, do not give physical shock nor disconnect network and power. Otherwise, your
WebEye can be damaged seriously, which may result inappropriate operation or
operation failure.
If you failed in upgrading WebEye firmware or WebEye does not operate properly after
successful upgrading process, contact WebGate distributor in your area.
1. Connect WeEye to a PC.
• Directly connect WebEye to a PC with a crossover cable. This connection is recommended.
Crossover cable
•
Connect WebEye to a PC through a HUB with a direct cable.
HUB
Direct cable
Local PC
* This process can also be done on a remote network. However it is not recommended.
67
WebEye E10/E104 User’s Guide
2. Upgrade firmware with upgrading program
(1) Open ‘MS Dos ’ window and practice a
command <c:\arp –d>.
(2) Select WebEye to update by clicking
on IP address or MAC address in the list.
When an IP address appears in the blanks
of “Selected IP address,” type in the
administrator’s password in the “Administ
-rator’s password” blank.
Click “Start” button.
(3) Click “Yes” button to confirm upgrading process.
(4) Click ‘OK’ button to start rebooting process.
(5) If WebEye has a different firmware version, the
program will ask if it should be replaced with a new
one. Confirm by clicking “Yes.”
(6) The program will ask to format user file system. To
maintain any changes made to WebEye’s homepage, click
“No.” To format user file system and reload the default
settings, click “Yes.”
(7) When upgrade is complete, reboot WebEye by
clicking the “Ok” button.
(8) To upgrade other WebEyes, repeat the above process. Otherwise, click “Exit.”
68
WebEye E10/E104 User’s Guide