Step 1 *Remove the two screws from the top of the base

Norris Parts Repair Manual
Dell 2000FP Logic Board
Installation Instructions
Copyright©2006 – All Rights Reserved - Distribution or Duplication of this document is prohibited.
1
Norris Parts Repair Manual
2
The Dell 2000FP was designed for a wide variety of users ranging from the home, small office, or
corporate environment. It utilizes a 20.1-inch (51.0cm) Active Matrix TFT LCD that displays sharp and
brilliant images of text and graphics with a maximum resolution up to 1600 x 1200 pixels.
Common Problems associated with this model:
1.
2.
3.
4.
Black Display (screen goes black).
Front Panel Buttons won’t work.
Front Panel Lights stay yellow.
Picture blurring.
Resolving these issues (Part Replacement):
1. Replace the logic board 48.L3701.A02 Manufactured by BENQ.
This Logic Board works on the following models:
BRAND
MODEL
REMARK
DELL
2000FP
20.1" LCD MONITOR
Disassembly Instructions:
1. Place monitor face down on flat surface using a soft towel to avoid scratching the LCD screen.
2. Use a cup or other small container to hold the screws as they are removed.
3. It is recommended, not required, that you purchase a static wrist guard or other anti-static
guard. These can be purchased at a nominal cost at a computer hardware store or electronics
repair shop.
4. Make sure the unit is unplugged and the power supply/plug is removed from the unit.
5. Important: Do not apply force onto the LCD screen at anytime, this will cause permanent
damage.
6. This manual is provided as a reference guide. If you do not understand disassembly process
or you do not feel that you are competent to perform the repair, then you should have the
repair completed by a professional repair technician.
Disclaimer:
Norris Parts provides this manual for reference only. Norris Parts is not responsible for any actions
taken by the user of this manual. Norris Parts is not responsible for damage resulting from the repair
or use of any equipment referenced in this manual.
Copyright©2006 – All Rights Reserved - Distribution or Duplication of this document is prohibited.
Norris Parts Repair Manual
3
Disassembly
Step 1:
Remove the four (4) screws from the
top of the base.
Step 2:
Remove the base.
Step 3:
Remove the four (4) screws from the
back cover.
Copyright©2006 – All Rights Reserved - Distribution or Duplication of this document is prohibited.
Norris Parts Repair Manual
4
Step 4:
Stick a flat screw driver between the
back cover and the front bezel on
the bottom of the LCD.
Step 5:
Remove the back cover from the
bottom of the LCD.
Step 6:
Remove the back cover from the
bottom of the LCD.
Copyright©2006 – All Rights Reserved - Distribution or Duplication of this document is prohibited.
Norris Parts Repair Manual
5
Step 7:
Rotate the LCD to the side to
continue removing the back cover.
Step 8:
Rotate the LCD to the other side to
continue removing the back cover.
Copyright©2006 – All Rights Reserved - Distribution or Duplication of this document is prohibited.
Norris Parts Repair Manual
6
Step 9:
Remove the back cover.
Step 10:
Remove the two (2) screws from
the inverter board’s metal cover.
Step 11:
Remove the inverter board’s metal
cover.
Copyright©2006 – All Rights Reserved - Distribution or Duplication of this document is prohibited.
Norris Parts Repair Manual
7
Step 12:
Remove the fifteen (15) screws
from the logic board’s metal cover.
Step 13:
Remove the logic board’s metal
cover.
Copyright©2006 – All Rights Reserved - Distribution or Duplication of this document is prohibited.
Norris Parts Repair Manual
8
Step 14:
Unplug connector from the logic
board.
Step 15:
Unplug the two (2) connectors
from the logic board.
Step 16:
Unplug connector from the logic
board.
Copyright©2006 – All Rights Reserved - Distribution or Duplication of this document is prohibited.
Norris Parts Repair Manual
9
Step 17:
Unplug connector from the logic
board.
Step 18:
Remove the seven (7) screws from
the logic board.
Copyright©2006 – All Rights Reserved - Distribution or Duplication of this document is prohibited.
Norris Parts Repair Manual
10
Step 19:
Remove the logic board.
Step 20 – Reassembly
Inspect new part ensuring that any packing materials or tape are removed.
Follow the directions in reverse to complete the installation of the replacement part. Make
sure that all connectors are plugged in. Make sure that you replace all screws into their
assemblies.
Copyright©2006 – All Rights Reserved - Distribution or Duplication of this document is prohibited.