Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Update Alert: Firmware updates are posted on the web on a regular basis. We recommend
that you check for firmware and/or install guide updates prior to installing this product.
Installation Guide
This guide supports the installation of a DBALL in Remote Start Ready (RSR) mode with or without a
Plug & Play (CHTHD1 or CHTHD2) T-Harness (Optional). This solution offers three (3) configuration
options to control your system; 3x OEM Lock Remote Start Activation*, RF Kit or SmartStart (all sold
separately). Refer to page 24 for a list of RF kits and their part numbers.
*3x OEM Lock Remote Start Activation is a feature that allows users to control the aftermarket remote
starter using the factory (OEM) remote control. See page 2 for more information.
Note: Only available on certain models, check the Vehicle Application Guide for compatibility with
specific year and model.
Remote Start Ready (RSR) is a function that enables the interface module to remote start the vehicle
completely on its own. Consequently, there is no need for an aftermarket or an OEM remote starter in order to
start the vehicle from a distance. An RSR solution is commonly referred to as a Standalone installation.
Important!
This product is NOT compatible with vehicles equipped with a manual transmission.
Index
Important Information.............................................................................................................................................................................. 02
Vehicle Application Guide........................................................................................................................................................................ 03
Installation
Type 1a (with T-Harness).......................................................................................................................................................................
Type 1b (without T-Harness)..................................................................................................................................................................
Type 2a (with T-Harness).......................................................................................................................................................................
Type 2b (without T-Harness)..................................................................................................................................................................
Type 3a (with T-Harness).......................................................................................................................................................................
Type 3b (without T-Harness)..................................................................................................................................................................
Type 4a (with T-Harness).......................................................................................................................................................................
Type 4b (without T-Harness)..................................................................................................................................................................
Type 5 (without T-Harness)....................................................................................................................................................................
04
05
07
08
10
11
13
14
16
Programming
Module Programming and Reset for Installation Types 1 to 4.................................................................................................................
Module Programming and Reset for Installation Type 5.........................................................................................................................
Module Reset..........................................................................................................................................................................................
Feature and Option List..........................................................................................................................................................................
Feature Programming.............................................................................................................................................................................
18
20
21
22
22
LED Diagnostics and Troubleshooting....................................................................................................................................................
Optional RF Kits......................................................................................................................................................................................
Using a DBALL-CHRYSLER RSR..........................................................................................................................................................
Limited One-Year Consumer Warranty...................................................................................................................................................
23
24
26
27
SmartStart Compatible
See page 2 for more information.
† Chrysler, Dodge, Jeep and Volkswagen are registered trademarks and property of their respective companies.
© 2012 Directed. All rights reserved.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 2
Important Information
3x OEM Lock Remote Start Activation
This feature enables you to start/stop the vehicle using the OEM remote.
Press the OEM remote LOCK button three (3) times within three (3) seconds to start the vehicle. To stop the vehicle,
press the LOCK button three (3) more times.
The OEM remote lock and unlock functions are inactive when the key is inserted into the ignition; therefore, the 3x
OEM Lock Remote Start Activation feature cannot be used for idle mode.
SmartStart Compatible
Important!
SmartStart 200/250 Revision B is equipped with D2D, which means it can be connected to an interface
module and used in Remote Start Ready (RSR) mode without the use of a remote starter.
In order to use the SmartStart 200/250 Revision B with an interface, you must enable the D2D mode within
SmartStart by grounding the loose gray wire coming out of the device, as well as connecting it to the web to
complete its configuration.
© 2012 Directed. All rights reserved.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 3
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
ST-Keysense Status
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
ST-Ignition Status
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
5
5
5 5
12 11 10 09 08
07
06
05 04
3 3 3 3
3 3 3 3 3* or 4* 3* or 4*
1 1 1 1 1
5
5
5 5
1 1 1 1
1 1 1 1
2 2 2
4
4
3 3 3 3
3
1
3 3
3
1 1 1 1 1
5
5
5 5
1 1
2
4
4
4
3 3 3 3
3
1 1 1 1
3
3
3* or 4*
12 11 10 09 08
07
06
05 04
2 2 2
4
4
3 3 3 3
3
1
2 2 2
4
4
4
1
3 3 3 3
3 3 3 3 3
3
3 3 3 3 3
3
3 3 3 3 3
3
12 11 10 09 08
07
06
05 04
3 3
3
12 11 10 09 08
07
06
05 04
1
1
1
1
12 11 10 09 08
07
06
05 04
1 1 1 1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
ST-Hand Brake Status
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
3
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
SS-Entry Monitoring ALL
Door Pins
SS-Entry Monitoring Driver
Door Pin
SS-Entry Monitoring
Trunk/Hatch Pin
ST-Brake Status (foot
brake)
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
5
RS-Tach / RPM Output
1
4
3
3
3
1
RS-Smart Start
1
4
3
3
3
1
3
5
4
3
3
3
1
•
•
•
•
•
•
•
•
•
•
•
RS-Remote Start Ready Std
Ign-RFTD
3
•
•
•
•
•
RS-Remote Start Ready
•
•
•
•
•
•
•
•
•
•
•
KI-Key & Ignition.switch
Interface
PK-Immobilizer Bypass-Data
No Key Req'd
RS 3x LOCK START (Start
control using OEM Remote)
RS-RAP Shut Down
(Remote ACC Power)
•
•
•
•
•
•
•
•
•
•
•
KI-Chrysler MUXX Activation
•
•
•
•
•
•
•
•
•
•
•
FOB-Control of aftermarket
alarm with OEM remote
•
•
•
•
•
•
•
•
•
•
•
•
DL-Trunk / Hatch Release
•
•
•
•
•
•
•
•
•
•
•
3
DL-Sliding Door Control
Driver
DL-Sliding Door Control
Passenger
DL-Driver Priority Unlock
5
DL-Door Unlock
5
4
DL-Door Lock Control
4
DL-Disarm Factory Security
4
AV-Parking Lights Control
4
3
5
4
3
2004
2
2005
2008
2
2006
2009
2
2007
2010
Chrysler
200
300/300c
300/300c
Aspen
Pacifica
PT Cruiser
Sebring
Sebring Convertible
Sebring Sedan
Town & Country
Town & Country
Dodge
Avenger
Caliber
Caravan
Caravan
Challenger
Challenger (Smart Key)
Charger
Charger
Dakota
Durango
Durango
Grand Caravan
Grand Caravan
Journey
Magnum
Magnum
Nitro
RAM
RAM
Jeep
Commander
Commander
Compass
Grand Cherokee
Grand Cherokee
Grand Cherokee
Grand Cherokee (Smart Key)
Liberty
Patriot
Wrangler
Wrangler Unlimited
Mitsubishi
Raider
Ram
1500
2500
3500
C/V
Volkswagen
Routan
2011
2012
Vehicles
DL-Arm Factory Security
Vehicle Application Guide
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
*To select the proper install type, locate the ignition switch connector and select your install type as illustrated below:
(+) Start, Pin 4
No Start wire
Installation Type 3 does not
have a Start wire
5 or 6
1
Connector side view
at ignition switch
Installation Type 4
has a Start wire
5 or 6
1
Connector side view
at ignition switch
© 2012 Directed. All rights reserved.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 4
Installation Type 1a (with T-Harness)
Important!
The Hood Pin and Neutral Safety Switch are mandatory security devices, but are NOT supplied with the DBALL.
The optional XL202 and antenna are not included and MUST be
purchased separately.
(+)12v
4
Programming
Button
TX
(-) Ground
4 pins
SmartStart
RX
LED
RX
(-) Ground
TX
(+)12v
2 pins
D2D (4 pins, white)
You can either connect to an XL202 module
or to a SmartStart module.
To vehicle’s
(+) Parking Lights
White/Purple
86
Configuration Wires (Gray & White)
Connect Gray wire to (-) Ground
LED
5 pins
OR
4
Antenna
XL202
SmartStart is optional and not included. It MUST be purchased
separately.
XOVER
CABLE
85
87
Hood Pin
87a
30
+12v
Neutral Safety Switch
14
Fuse 15A
ONLY connect for
Dodge Journey.
2: Green/Black: (-) Parking Lights via Relay*
OR*
10
12
See page 6 for
wiring information
6: White/Black: (-) Hood
8: Violet/Green: Parking Light MUX*
9: Violet/Brown: Parking Light MUX*
10: Yellow/Black: RAP OFF
2
(+) 12v
RF
4
(-) Driver door pin
Programming button
LED
DBALL
RX
(-) Ground
TX
Purple wire in
driver kick panel
Ignition
Barrel
CHTHD1
(optional)
Facing view
Behind Ignition Switch
Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.
*See Parking Lights wiring reference chart for the appropriate Parking Lights configuration.
© 2012 Directed. All rights reserved.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 5
Installation Type 1b (without T-Harness)
Important!
The Hood Pin and Neutral Safety Switch are mandatory security devices, but are NOT supplied with the DBALL.
The optional XL202 and antenna are not included and MUST be
purchased separately.
(+)12v
4
Programming
Button
XL202
Configuration Wires (Gray & White)
Connect Gray wire to (-) Ground
LED
5 pins
OR
TX
(-) Ground
4 pins
RX
(-) Ground
TX
(+)12v
LED
2 pins
D2D (4 pins, white)
You can either connect to an XL202 module
or to a SmartStart module.
To vehicle’s
(+) Parking Lights
White/Purple
86
SmartStart
RX
4
Antenna
SmartStart is optional and not included. It MUST be purchased
separately.
XOVER
CABLE
85
87
87a
Hood Pin
30
3: Tan/Black: HSCAN High
4: Tan: HSCAN Low
+12v
Fuse 15A
(+) 12v
7: Brown: (+) 12v
8: Yellow
Neutral Safety Switch
14
ONLY connect for
Dodge Journey.
9: Orange/Yellow
(+) 12v
(-) Ground
13: Red: (+) 12v
14: Black: (-) Ground
2: Green/Black: (-) Parking Lights via Relay*
OR*
10
12
See page 6 for
wiring information
6: White/Black: (-) Hood
8: Violet/Green: Parking Light MUX*
9: Violet/Brown: Parking Light MUX*
10: Yellow/Black: RAP OFF
2
(+) 12v
RF
4
(-) Driver door pin
Programming button
LED
DBALL
RX
(-) Ground
TX
(+) Ignition
CAN Low
6
CAN High
Purple wire in
driver kick panel
Ignition
Barrel
1
Connector side view
at ignition switch
12
7
Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.
*See Parking Lights wiring reference chart for the appropriate Parking Lights configuration.
© 2012 Directed. All rights reserved.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 6
Parking Light Vehicle Wiring Reference Chart (Type 1)
Vehicle
(+) / (-)
Light switch,
black 10-pin plug
DBALL Output from
12 Pin connector
Years Vehicle Wire
Location on vehicle
Town & Country
2011+ White/Green
Black connector at light switch, pin 3
MUX
8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
Town & Country
2008-10 White/Brown
Black connector at light switch, pin 1
MUX
8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
Chrysler
Dodge
Caravan
2011+ White/Green
Black connector at light switch, pin 3
MUX
Caravan
2008-10 White/Brown
Black connector at light switch, pin 1
MUX
Challenger
2008-11 White/Brown
Black connector at light switch, pin 1
MUX
Challenger (Smart Key)
2008-11 White/Brown
Black connector at light switch, pin 1
MUX
Durango
2011+ White/Green
Black connector at light switch, pin 3
MUX
Grand Caravan
2011+ White/Green
Black connector at light switch, pin 3
MUX
Grand Caravan
2008-10 White/Brown
Black connector at light switch, pin 1
MUX
Journey
2009-10 White/Purple
Passenger kick panel
RAM
2009-12 White
Black connector at light switch, pin 1
(+)
MUX
8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
2: Green/Black: (-) Parking Lights
via Relay
8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
Grand Cherokee
(Smart Key)
4
3
2
1
9
8
7
6
Light switch,
black 6-pin plug
6
5
4
3
2
1
Jeep
Grand Cherokee
5
10
2011+ White/Green
Black connector at light switch, pin 1
MUX
2011+ White/Green
Black connector at light switch, pin 1
MUX
8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
Ram
1500
2012
White
Black connector at light switch, pin 1
MUX
2500
2012
White
Black connector at light switch, pin 1
MUX
3500
2012
White
Black connector at light switch, pin 1
MUX
C/V
2012
White
Black connector at light switch, pin 1
MUX
8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
Volkswagen
Routan
2011+ White/Green
Black connector at light switch, pin 3
MUX
Routan
2009-10 White/Brown
Black connector at light switch, pin 1
MUX
8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
© 2012 Directed. All rights reserved.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 7
Installation Type 2a (with T-Harness)
Important!
The Hood Pin and Neutral Safety Switch are mandatory security devices, but are NOT supplied with the DBALL.
The optional XL202 and antenna are not included and MUST be
purchased separately.
(+)12v
XL202
Configuration Wires (Gray & White)
Connect Gray wire to (-) Ground
LED
5 pins
OR
TX
(-) Ground
4 pins
SmartStart
RX
4
Antenna
4
Programming
Button
SmartStart is optional and not included. It MUST be purchased
separately.
RX
(-) Ground
TX
(+)12v
LED
2 pins
D2D (4 pins, white)
You can either connect to an XL202 module
or to a SmartStart module.
XOVER
CABLE
Hood Pin
Twisted pair in the kick panel
White/Orange
White/Gray, White
or White/Pink
Neutral Safety Switch
5: White/Orange: FTCAN High
6: White: FTCAN Low
14
2: Green/Black: (-) Parking Lights*
12
10
OR*
See page 9 for
wiring information
6: White/Black: (-) Hood
8: Violet/Green: Parking Light MUX*
9: Violet/Brown: Parking Light MUX*
(-) Driver door pin
10: Yellow/Black: RAP OFF
2
4
Programming button
Purple wire in
driver kick panel
Ignition
Barrel
(+) 12v
RF
LED
DBALL
RX
(-) Ground
TX
CHTHD1
(optional)
Facing view
Behind Ignition Switch
Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.
*See Parking Lights wiring reference chart for the appropriate Parking Lights configuration.
© 2012 Directed. All rights reserved.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 8
Installation Type 2b (without T-Harness)
Important!
The Hood Pin and Neutral Safety Switch are mandatory security devices, but are NOT supplied with the DBALL.
The optional XL202 and antenna are not included and MUST be
purchased separately.
(+)12v
4
Programming
Button
Configuration Wires (Gray & White)
Connect Gray wire to (-) Ground
LED
5 pins
OR
TX
(-) Ground
4 pins
SmartStart
RX
4
Antenna
XL202
SmartStart is optional and not included. It MUST be purchased
separately.
RX
(-) Ground
TX
(+)12v
LED
2 pins
D2D (4 pins, white)
You can either connect to an XL202 module
or to a SmartStart module.
XOVER
CABLE
Hood Pin
Twisted pair in the kick panel
White/Orange
White/Gray, White
or White/Pink
5: White/Orange: FTCAN High
6: White: FTCAN Low
Neutral Safety Switch
3: Tan/Black: HSCAN High
4: Tan: HSCAN Low
7: Brown: (+) 12v
14
(+) 12v
8: Yellow
9: Orange/Yellow
(+) 12v
(-) Ground
13: Red: (+) 12v
14: Black: (-) Ground
2: Green/Black: (-) Parking Lights*
OR*
10
12
See page 9 for
wiring information
6: White/Black: (-) Hood
8: Violet/Green: Parking Light MUX*
9: Violet/Brown: Parking Light MUX*
(+) Ignition
(-) Driver door pin
(+) 12v
RF
4
CAN Low
2
CAN High
10: Yellow/Black: RAP OFF
Programming button
LED
DBALL
RX
(-) Ground
TX
Purple wire in
driver kick panel
6
1
Connector side view
at ignition switch
Ignition
Barrel
12
7
Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.
*See Parking Lights wiring reference chart for the appropriate Parking Lights configuration.
© 2012 Directed. All rights reserved.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 9
Parking Light Vehicle Wiring Reference Chart (Type 2)
Vehicle
Years Vehicle Wire
Location on vehicle
(+) / (-)
Light switch,
black 10-pin plug
DBALL Output from
12 Pin connector
Chrysler
300/300c
2008-10 White/Brown
Black connector at light switch, pin 1
MUX
2008-10 White/Brown
Black connector at light switch, pin 1
MUX
8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
Dodge
Charger
Magnum
2008
White/Brown
Black connector at light switch, pin 1
Jeep
Commander
2008-10 White/Dk. Blue Hazar light switch
Grand Cherokee 2008-10 White/Dk. Blue Hazar light switch
8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
8: Violet/Green: Parking Light MUX
MUX
9: Violet/Brown: Parking Light MUX
(-)
(-)
2: Green/Black: (-) Parking Lights
2: Green/Black: (-) Parking Lights
1 2 3 4 5
6 7 8 9 10
Jeep Commander & Jeep
Grand Cherokee
Optional parking light connection
© 2012 Directed. All rights reserved.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 10
Installation Type 3a (with T-Harness)
Important!
The Hood Pin and Neutral Safety Switch are mandatory security devices, but are NOT supplied with the DBALL.
The optional XL202 and antenna are not included and MUST be
purchased separately.
(+)12v
4
Programming
Button
Configuration Wires (Gray & White)
Connect Gray wire to (-) Ground
LED
5 pins
OR
TX
(-) Ground
4 pins
SmartStart
RX
4
Antenna
XL202
SmartStart is optional and not included. It MUST be purchased
separately.
RX
(-) Ground
TX
(+)12v
LED
2 pins
D2D (4 pins, white)
You can either connect to an XL202 module
or to a SmartStart module.
XOVER
CABLE
Hood Pin
14
See page 12 for
wiring information
Neutral Safety Switch
2: Green/Black: (-) Parking Lights
10
6: White/Black: (-) Hood
12
10: Yellow/Black: RAP OFF
To vehicle’s
(+) Parking Lights
(-) Driver door pin
2
85
87
(+) 12v
Programming button
RX
(-) Ground
LED
4
86
Purple wire in
driver kick panel
RF
DBALL
TX
87a
30
+12v
Fuse 15A
CHTHD2
(optional)
1
8
Connector side view
at ignition switch
Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.
© 2012 Directed. All rights reserved.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 11
Installation Type 3b (without T-Harness)
Important!
The Hood Pin and Neutral Safety Switch are mandatory security devices, but are NOT supplied with the DBALL.
The optional XL202 and antenna are not included and MUST be
purchased separately.
(+)12v
4
Programming
Button
Configuration Wires (Gray & White)
Connect Gray wire to (-) Ground
LED
5 pins
OR
TX
(-) Ground
4 pins
SmartStart
RX
4
Antenna
XL202
SmartStart is optional and not included. It MUST be purchased
separately.
RX
(-) Ground
TX
(+)12v
LED
2 pins
D2D (4 pins, white)
You can either connect to an XL202 module
or to a SmartStart module.
See page 12 for
wiring information
XOVER
CABLE
Hood Pin
To vehicle’s
(+) Parking Lights
86
3: Tan/Black: HSCAN High
85
87
30
(+) 12v
(+) 12v
(-) Ground
+12v
Fuse 15A
4: Tan: HSCAN Low
7: Brown: (+) 12v
8: Yellow: (+) Ignition
13: Red: (+) 12v
14: Black: (-) Ground
Neutral Safety Switch
14
87a
6: White/Black: (-) Hood
12
2: Green/Black: (-) Parking Lights
(-) Driver door pin
10
8: Violet/Green: Multiplex Output
9: Violet/Brown: Multiplex Output
10: Yellow/Black: RAP OFF
Purple wire in
driver kick panel
2
(+) 12v
Programming button
RX
(-) Ground
LED
4
RF
DBALL
TX
CAN Low, Pin 7
CAN High, Pin 6
(+) Ignition, Pin 3
MUX, Pin 1
1
8
Connector side view
at ignition switch
Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.
© 2012 Directed. All rights reserved.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 12
Parking Light Vehicle Wiring Reference Chart (Type 3)
Vehicle
Years Wire
Chrysler
200
Aspen
Sebring
Sebring Convertible
Sebring Sedan
Dodge
Avenger
Caliber
Dakota
Durango
Nitro
RAM
Jeep
Compass
Liberty
Patriot
Wrangler
Wrangler Limited
Mitsubishi
Raider
(+) / (-) Location
2011
2007-09
2007-10
2008-10
2007-10
White/Violet
Pink/Red
White/Violet
White/Violet
White/Violet
(+)
(+)
(+)
(+)
(+)
Driver kick
Driver kick
Driver kick
Driver kick
Driver kick
2008-11
2007-11
2007-11
2007-09
2007-11
2006-08
White/Violet
White/Violet
Pink/Red
Pink/Red
White/Violet
White/Gray
(+)
(+)
(+)
(+)
(+)
(+)
Driver kick panel
Driver kick panel
Underhood fuse box, black 20-pin plug, pin 15
Driver kick fuse box, black 40-pin plug, pin 6
Driver kick panel
Above driver kick, gray 74-pin plug, pin 19
2007-11
2008-10
2007-12
2007-12
2007-12
White/Violet
White/Violet
White/Violet
White/Violet
White/Violet
(+)
(+)
(+)
(+)
(+)
Driver kick panel
Driver kick panel
Driver kick panel
Passenger kick panel
Passenger kick panel
(+)
Underhood fuse box, black 20-pin plug, pin 15
2007-09 Pink/Red
Driver kick fuse box,
black 40-pin plug
Underhood fuse box,
black 20-pin plug
panel
fuse box, black 40-pin plug, pin 6
panel
panel
panel
Above driver kick,
gray 74-pin plug
1
7 38 44
10 9 8 7 6 5 4 3 2 1
25
39
9
1
20 19 18 17 16 15 14 13 12 11
46
3
55
10
37
3
28
12
33 21
17
5
36 24
20
8
29
40
16
64
17
65
20
4
32
59
60
61
14
15
16
13
38
58
11
29
72
2
31 37 68 74
© 2012 Directed. All rights reserved.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 13
Installation Type 4a (with T-Harness)
Important!
The Hood Pin and Neutral Safety Switch are mandatory security devices, but are NOT supplied with the DBALL.
The optional XL202 and antenna are not included and MUST be
purchased separately.
(+)12v
4
Programming
Button
Configuration Wires (Gray & White)
Connect Gray wire to (-) Ground
LED
5 pins
OR
TX
(-) Ground
4 pins
SmartStart
RX
4
Antenna
XL202
SmartStart is optional and not included. It MUST be purchased
separately.
RX
(-) Ground
TX
(+)12v
LED
2 pins
D2D (4 pins, white)
You can either connect to an XL202 module
or to a SmartStart module.
XOVER
CABLE
Hood Pin
(+) Parking Lights
14
Neutral Safety Switch
See page 15 for
wiring information.
11: Yellow/Red: (+) Start
2: Green/Black: (-) Parking Lights
6: White/Black: (-) Hood
10
To vehicle’s
(+) Parking Lights
12
86
85
87
87a
30
2
(+) 12v
Programming button
RX
(-) Ground
LED
4
+12v
RF
DBALL
TX
Fuse 15A
CHTHD2
(optional)
1
8
5 or 6
(+) Start, Pin 4
Connector side view
at ignition switch
Violet/Brown, Pin 2
1
Connector side view
at ignition switch
Cut Purple/Brown
wire, Pin 8
(on female end)
Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.
© 2012 Directed. All rights reserved.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 14
Installation Type 4b (without T-Harness)
Important!
The Hood Pin and Neutral Safety Switch are mandatory security devices, but are NOT supplied with the DBALL.
The optional XL202 and antenna are not included and MUST be
purchased separately.
(+)12v
4
Programming
Button
Configuration Wires (Gray & White)
Connect Gray wire to (-) Ground
LED
5 pins
OR
TX
(-) Ground
4 pins
SmartStart
RX
4
Antenna
XL202
SmartStart is optional and not included. It MUST be purchased
separately.
RX
(-) Ground
TX
(+)12v
LED
2 pins
D2D (4 pins, white)
You can either connect to an XL202 module
or to a SmartStart module.
(+) Parking Lights
To vehicle’s
(+) Parking Lights
86
CABLE
See page 15 for
wiring information.
85
87
XOVER
87a
30
Hood Pin
+12v
Fuse 15A
3: Tan/Black: HSCAN High
4: Tan: HSCAN Low
(+) 12v
(+) 12v
(-) Ground
7: Brown: (+) 12v
8: Yellow: (+) Ignition
11: Yellow/Red: (+) Start
12: Brown/Red: (+) 12v
13: Red: (+) 12v
14: Black: (-) Ground
14
(+) 12v
Neutral Safety Switch
2: Green/Black: (-) Parking Lights
6: White/Black: (-) Hood
10
2
1 1
Connector side view
at ignition switch
RF
(+) 12v
Programming button
RX
(-) Ground
LED
4
CAN Low, Pin 7
CAN High, Pin 6
Violet/Brown, Pin 2
(+) Start, Pin 4
(+) Ignition, Pin 3
5 or 6
12
8: Violet/Green: Multiplex Output
9: Violet/Brown: Multiplex Output
DBALL
TX
8
Connector side view
at ignition switch
Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.
© 2012 Directed. All rights reserved.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 15
Parking Light Vehicle Wiring Reference Chart (Type 4)
Vehicle
Years Wire
Chrysler
300/300c
PT Cruiser
Dodge
Caliber
Charger
Magnum
RAM
Jeep
Commander
Grand Cherokee
(+) / (-) Location
2005-07 White/Violet
2006-10 White/Violet
(+)
(+)
Passenger kick panel
Driver kick panel
2007-11
2006-07
2005-07
2006
(+)
(+)
(+)
(+)
Driver kick panel
Passenger kick panel
Passenger kick panel
Above driver kick, gray 74-pin plug, pin 19
(-)
(-)
Hazard light switch
Hazard light switch
White/Violet
White/Violet
White/Violet
White/Gray
2006-07 White/Dk. Blue
2005-07 White/Dk. Blue
Above driver kick,
gray 74-pin plug
1
7 38 44
46
3
55
10
58
11
59
60
61
14
15
16
64
17
65
20
29
72
31 37 68 74
© 2012 Directed. All rights reserved.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 16
Installation Type 5 (without T-Harness)
Important!
The Hood Pin and Neutral Safety Switch are mandatory security devices, but are NOT supplied with the DBALL.
The optional XL202 and antenna are not included and MUST be
purchased separately.
(+)12v
4
Programming
Button
Configuration Wires (Gray & White)
Connect Gray wire to (-) Ground
LED
5 pins
OR
TX
(-) Ground
4 pins
SmartStart
RX
4
Antenna
XL202
SmartStart is optional and not included. It MUST be purchased
separately.
RX
(-) Ground
TX
(+)12v
LED
2 pins
D2D (4 pins, white)
You can either connect to an XL202 module
or to a SmartStart module.
XOVER
CABLE
Hood Pin
2: Violet/Yellow: J1850
8: Yellow
9: Orange/Yellow
Neutral Safety Switch
14
(+) 12v
(+) 12v
(-) Ground
Parking Lights
11: Yellow/Red: (+) Start
12: Brown/Red: (+) 12v
13: Red: (+) 12v
14: Black: (-) Ground
2: Green/Black: (-) Parking Lights
6: White/Black: (-) Hood
12
7: Gray/Black: (+) Ignition
10
See page 17 for
wiring information
8: Violet/Green: Multiplex Output
9: Violet/Brown: Multiplex Output
2
1
Module-Sentry Key
Remote Entry
(+) 12v
RF
4
Violet/Brown, Pin 2
6
(+) Start, Pin 4
J1850
(+) Ignition, Pin 3
Sentry Key
(+) Ignition
Programming button
LED
DBALL
RX
(-) Ground
TX
1
Connector
side view
Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.
© 2012 Directed. All rights reserved.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 17
Parking Light Vehicle Wiring Reference Chart (Type 5)
Vehicle
Years Wire
Chrysler
Pacifica
Town & Country
Dodge
Caravan
Grand Caravan
2004-08 Brown/White (-1K)
2004-07 White/Orange
Headlight switch,
black 12-pin plug
(+) / (-) Location
MUX Headlight switch, black 12-pin plug, pin 6
(+) Driver kick panel
2004-07 White/Orange
2004-07 White/Orange
(+)
(+)
Driver kick panel
Driver kick panel
(+) Parking Lights
1 2 3 4 5 6
7 8 9 10 11 12
(MUX) Parking Lights
1KΩ
To vehicle’s
(+) Parking Lights
86
To vehicle’s
(MUX) Parking Lights
85
87
2: Green/Black: (-) Parking Lights
87a
30
OR
86
85
87
87a
2: Green/Black: (-) Parking Lights
30
+12v
+12v
Fuse 15A
Positive (+)
MUX
© 2012 Directed. All rights reserved.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 18
Module Programming for Installation Types 1 to 4 (WITH Factory Keyless)
Refer to the LED Diagnostics section on page 23 for more information and for troubleshooting purposes.
Important
Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to
ensure everything is correct prior to moving onto the next step.
Note: Before connecting either the XL202 or SmartStart module to DBALL, it is important to ensure that the proper
communication protocol is enabled on DBALL using XpressVIP. This selection is done by:
1. Going to www.xpresskit.com.
2. Selecting the make, model and year of the vehicle.
3. On the search result page, click on the Flash it button.
4. The flash page will then be displayed listing the D2D type settings. Make your selection and flash the module.
To use DBALL with an:
§ RF Kit and XL202, D2D (RFTD) must be selected.
§ SmartStart (Revision B), D2D (SmartStart) must be selected.
Warning against resetting the DBALL module before executing the programming sequence!
A reset will erase all the settings configured on the module using the web tool (see the above instructions). Therefore, if you reset
before executing the programming sequence, you will HAVE to re-flash the module in order to re-configure the desired options.
DBALL Module Programming
1
Connect the SmartStart or XL202 unit into the D2D port of the DBALL prior to
connecting the power.
2
Connect the 10-pin, 12-pin and 14-pin
harnesses to DBALL, then wait until the
LED turns ON solid red or flashes orange.
OFF
3
START
or
&
rd
3
st
1
nd
2
Solid
Flashes
Push-to-Start (PTS) Ignition
Important: Do NOT press the brake pedal.
Press the Push-to-Start (PTS) button twice to
turn the ignition ON.
Do NOT
press the
brake pedal
ENGINE
START
STOP
2X
PUSH
It is important to wait for the LED to start flashing
green. Refer to the LED Diagnostics section on
page 23 for troubleshooting if the LED does not
flash green within 15 seconds.
N
Key IN
in
14-p 2-pin
1
D2D 0-pin
1
Key Ignition
Insert the key into the ignition barrel and turn it
to the ON position.
It is important to wait for the LED to start flashing
green. Refer to the LED Diagnostics section on
page 23 for troubleshooting if the LED does not
flash green within 15 seconds.
O
3
D2D 0-pin
1
&
Flashes
N
IG
5
Press LOCK or UNLOCK on the
factory transmitter. The LED turns
ON solid green OR orange for 3 seconds
and then turns off.
Key OUT
START
4
Press the Push-to-Start
(PTS) button once more
to turn the ignition OFF.
or
&
1X
ENGINE
START
STOP
or
Solid
PUSH
&
IC
N
PA
4
Turn the key to the OFF
position and remove it
from the ignition barrel.
OFF
Flashes
Solid
Off
Important! If connected to a SmartStart, please ensure that its Gray wire is connected to a ground source or the D2D
communication between the two (2) modules will NOT work.
© 2012 Directed. All rights reserved.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 19
Module Programming for Installation Types 1 to 4 (WITHOUT Factory Keyless)
Refer to the LED Diagnostics section on page 23 for more information and for troubleshooting purposes.
Important
Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to
ensure everything is correct prior to moving onto the next step.
Note: Before connecting either the XL202 or SmartStart module to DBALL, it is important to ensure that the proper
communication protocol is enabled on DBALL using XpressVIP. This selection is done by:
1. Going to www.xpresskit.com.
2. Selecting the make, model and year of the vehicle.
3. On the search result page, click on the Flash it button.
4. The flash page will then be displayed listing the D2D type settings. Make your selection and flash the module.
To use DBALL with an:
§ RF Kit and XL202, D2D (RFTD) must be selected.
§ SmartStart (Revision B), D2D (SmartStart) must be selected.
Warning against resetting the DBALL module before executing the programming sequence!
A reset will erase all the settings configured on the module using the web tool (see the above instructions). Therefore, if you reset
before executing the programming sequence, you will HAVE to re-flash the module in order to re-configure the desired options.
DBALL Module Programming
1
Connect the SmartStart or XL202 unit into the D2D port of the DBALL prior to
connecting the power.
2
Connect the 10-pin, 12-pin and 14-pin
harnesses to DBALL, then wait until the
LED turns ON solid red or flashes orange.
in
14-p 2-pin
1
OFF
O
Key IN
START
* Refer to the LED Diagnostics section on page 23 for troubleshooting
if the LED does not flash green within 15 seconds.
5
Turn the key to the OFF position and remove it from the ignition barrel.
&
Press & Hold
Flashes
or
Solid
Solid
&
&
Off
Key OUT
Release
OFF
4
Press and hold the Programming Button. The LED
turns ON solid green OR orange for 3 seconds and
then turns OFF. Release the Programming button.
&
N
It is important to wait for the LED to start flashing green.*
Flashes
Solid
Insert the key into the ignition barrel and turn it to the ON position.
3
or
&
nd
2
N
3rd
st
IG
D2D 0-pin
1
1
D2D 0-pin
1
START
Important! If connected to a SmartStart, please ensure that its Gray wire is connected to a ground source or the D2D
communication between the two (2) modules will NOT work.
© 2012 Directed. All rights reserved.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 20
Module Programming for Installation Type 5
Refer to the LED Diagnostics section on page 23 for more information and for troubleshooting purposes.
Important
Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to
ensure everything is correct prior to moving onto the next step.
Note: Before connecting either the XL202 or SmartStart module to DBALL, it is important to ensure that the proper
communication protocol is enabled on DBALL using XpressVIP. This selection is done by:
1. Going to www.xpresskit.com.
2. Selecting the make, model and year of the vehicle.
3. On the search result page, click on the Flash it button.
4. The flash page will then be displayed listing the D2D type settings. Make your selection and flash the module.
To use DBALL with an:
§ RF Kit and XL202, D2D (RFTD) must be selected.
§ SmartStart (Revision B), D2D (SmartStart) must be selected.
Warning against resetting the DBALL module before executing the programming sequence!
A reset will erase all the settings configured on the module using the web tool (see the above instructions). Therefore, if you reset
before executing the programming sequence, you will HAVE to re-flash the module in order to re-configure the desired options.
DBALL Module Programming
1
Connect the SmartStart or XL202 unit into the D2D port of the DBALL prior to
connecting the power.
2
Connect the 10-pin, 12-pin and 14-pin harnesses to
DBALL, then wait until the LED turns ON solid red.
in
14-p 2-pin
1
D2D 0-pin
1
Solid
OFF
Key IN
Insert the key into the ignition barrel without turning it and wait for
the LED to flash orange.
&
2nd
N
3rd
st
1
O
3
D2D 0-pin
1
START
&
N
O
START
or
&
Solid
Solid
&
When the green LED turns OFF, turn the key to the OFF position
and remove it from the ignition barrel.
&
Key OUT
OFF
Off
N
5
Key IN
IG
4
Insert the key into the ignition barrel and turn it to the ON
position. The LED will continue to flash orange. It will then
turn ON solid green OR orange for 3 seconds, before
turning OFF.
Refer to the LED Diagnostics section on page 23 for
troubleshooting if the LED does not turn ON solid green OR
orange within 15 seconds.
OFF
Flashes
START
Off
Important! If connected to a SmartStart, please ensure that its Gray wire is connected to a ground source or the D2D
communication between the two (2) modules will NOT work.
© 2012 Directed. All rights reserved.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 21
DBALL Module Reset
Refer to the LED Diagnostics section on page 23 for more information and for troubleshooting purposes.
Warning against resetting the DBALL module before executing the programming sequence!
A reset will erase all the settings configured on the module using the web tool (see the above instructions). Therefore, if
you reset before executing the programming sequence, you will HAVE to re-flash the module in order to re-configure the
desired options.
1a
If using in D2D: Connect the 10-pin, 12-pin & 14-pin
harnesses to the module. Press & hold the programming
button, then connect the 4-pin D2D harness.
in
14-p 2-pin
1
D2D 0-pin
1
3
th
5
st
rd
2nd
1
4
1b
If using in W2W: Connect the 10-pin & 12-pin harnesses to
the module. Press & hold the programming button, then
connect the 14-pin harness to the module.
th
in
14-p 2-pin
1
D2D 0-pin
1
4
st
1
th
2nd
3rd
2
Wait until the LED turns ON orange then release the
Programming button. The LED turns ON red.
&
&
Solid Orange
Release
Solid Red
© 2012 Directed. All rights reserved.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 22
Feature and Option List
It is recommended to configure all features and options listed below on the web when the module is being flashed;
however, a manual configuration is possible using the information found on this page.
Features
1
2
Operation
Option
RF Output Type**
No RF Output*
Activate this feature whenever an external
RFTD module is used (i.e. Directed
TM
SmartStart , XL201 or XL202).
Trunk
3
Aux1
4
Aux2
RFTD Output
No Option
Trunk*
Right Sliding Door
Left Sliding Door
No Option
Trunk
Passenger Sliding Door*
Driver Sliding Door
No Option
Trunk
Passenger Sliding Door
Driver Sliding Door*
** Important
The RF Output Type function must be
set to RFTD Output to enable the Remote
Start Ready (RSR) mode.
It will automatically be configured on the web
when flashed with the selected D2D_TYPE
D2D (RFTD) or D2D (SmartStart).
Any module reset will reset to default
option.
* Default option
Note: Features 2, 3 and 4 are programmable triggers.
Feature Programming
Programming
Button
To enter feature programming routine
- Turn the ignition ON, then OFF.
- Within 5 seconds, press and HOLD the programming button until the LED turns ON orange (after 3 seconds). Release the
Programming button.
- The LED will flash green once slowly to indicate the feature number is 1. After a short delay, the LED flashes red rapidly to indicate
the current option of feature 1 (i.e. 1x green followed by 1x red indicates feature 1 is set to option 1). The flashing sequence will
repeat until a new command is entered.
Changing feature options
- Press the lock/arm or unlock/disarm button on aftermarket transmitter to change the option of the selected feature.
- The LED flashes red rapidly the number of times equal to the current option number. After a short delay, the LED flashes green
slowly the number of times to indicate the current feature. The flashing sequence will repeat until a new command is entered.
Accessing another feature
- Press and release the programming button a number of times to advance from the current feature to the next desired feature.
- The LED flashes green slowly the number of times equal to the feature number. After a short delay, the LED flashes red rapidly to
indicate the current option of the current feature. The flashing sequence will repeat until a new command is entered.
When the maximum number of features or options is reached, the LED will start flashing again from the first feature or
option.
Once a feature is programmed
- Other features can be programmed.
- The feature programming can be exited.
Exiting feature programming
- No activity for 30 seconds; after 30 seconds, the LED will turn ON orange for 2 seconds to confirm the end of the programming
sequence.
OR
- Press and HOLD the programming button for 3 seconds. After 3 seconds, the LED will turn ON orange for 2 seconds to confirm the
end of the programming sequence.
© 2012 Directed. All rights reserved.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Page 23
LED Diagnostics and Troubleshooting
LED
Status
Rev.: 20120307
Description
Troubleshooting
Module Programming
Off
Off
Module has no power.
Check the power connections.
Solid
Solid red
The bus type cannot be detected.
Make sure the connections to the data bus are correct
and insert the key in the ignition switch.
Flashes
Flashes orange
The vehicle type cannot be
detected.
Insert the key in the ignition switch and turn to the ON
position. You may need to wait up to 10 seconds.
Waiting for keyless.
Remove the key from the ignition switch and press a
keyless button.
The Programming button was held
while powering up.
A reset occured. Release the button. The LED should
turn solid red.
Module was successfully
programmed or is already
programmed.
Normal operation.
Flashes
Solid
x3 secs
Flashes green
Solid green for
3 seconds
Types 1-5: Module was
successfully programmed without
diagnostics.
Active Ground While Running
Solid orange for
3 seconds
Normal operation.
Off
Off
Ground While Running (status) off.
Make sure the module was programmed, i.e. the D2D
harness is properly connected or the Ground While
Running (status) wire is connected.
Flashes
Flashes green
Ground While Running (status) on.
Normal operation.
Solid
x3 secs
Inactive Ground While Running
Flashes
1x
Flashes green
once (1)
Lock function has been executed.
If it does not flash, the bypass module did not receive
the signal. Verify the connections between the bypass
and the remote starter module.
Flashes
2x
Flashes green
twice (2)
Unlock function has been
executed.
If it does not flash, the bypass module did not receive
the signal. Verify the connections between the bypass
and the remote starter module.
Flashes
3x
Flashes green
three (3) times
Trunk release function has been
executed.
If it does not flash, the bypass module did not receive
the signal. Verify the connections between the bypass
and the remote starter module.
Flashes
4x
Flashes green
four (4) times
AUX1 or AUX2 function has been
executed.
If it does not flash, the bypass module did not receive
the signal. Verify the connections between the bypass
and the remote starter module.
© 2012 Directed. All rights reserved.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 24
Optional RF Kits
Note: RF kits are sold SEPARATELY. Request an order from Directed using the part numbers listed below.
9211VL
Viper 1-way Responder ONE - Plug & Play RF kit with XL202.
UPC: 093207 08488 1
Also available as:
§ Python: 9211PL
§ Clifford: 9211XL
9153VL
Viper 1-way - Plug & Play RF kit with XL202.
UPC: 093207 05660 4
Also available as:
§ Python: 9153PL
§ Clifford: 9153XL
9251VL
Viper 2-way Responder LE - Plug & Play RF kit with XL202.
UPC: 093207 08489 8
Also available as:
§ Python: 9251PL
§ Clifford: 9251XL
9752VL
Viper 2-way LC3 - Plug & Play RF kit with XL202.
UPC: 093207 08490 4
Also available as:
§ Python: 9752PL
§ Clifford: 9752XL
© 2012 Directed. All rights reserved.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 25
Optional RF Kits
Note: RF kits are sold SEPARATELY. Request an order from Directed using the part numbers listed below.
AF-RFK636
AF-RFK5225
Astrostart 2-way LED
Receiver kit with up to
1,500’ of range.
UPC: 093207 08752 3
Astrostart 2-way LCD
Receiver kit offering
XRTTM technology with up
to 5,000’ of range.
UPC: 093207 08753 0
AS-RFK1700
AS-RFK2300
Autostart 1-way Receiver
kit with up to 3,000’ of
range.
UPC: 093207 08738 7
Autostart 2-way LED
Receiver kit offering
TM
HDR technology with up
to 3,000’ of range.
UPC: 093207 08739 4
© 2012 Directed. All rights reserved.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 26
Using your DBALL-CHRYSLER RSR
2
Enter the vehicle, while making sure the key is inside with you.
Press button to
remote start*
* Your remote starter model may differ from the one shown in the illustration.
Enter vehicle
with the Smart
Key in hand
NIC
Important: Do NOT press the brake pedal.
3
4
Press the Push-to-Start (PTS) button twice to turn
the ignition ON.
You can now put the car in gear and drive off.
PA
1
Press the button to remote start the vehicle.
Do NOT
press the 2X
brake pedal
ENGINE
START
STOP
PUSH
Ready to
drive off
© 2012 Directed. All rights reserved.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Limited One Year Consumer Warranty
Rev.: 20120307
Page 27
For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed
Electronics. (“DIRECTED”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the
security or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or material
under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer;
and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the
following information: consumer’s name, address, telephone number, the authorized licensed dealer’s name and complete
product and Part description.
This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its
intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or
other causes not arising out of defect in materials or construction.
TO THE MAXIMUM EXTENTALLOWED BY LAW, EXCEPTAS STATED ABOVE, ALL WARRANTIES, INCLUDING BUT NOT
LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR
PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY
EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT
ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND
HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR
INSTALLERS. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER
VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE
FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM
AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE PRICE
OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT
LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS
OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE
ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR
REPAIR AT DIRECTED’S OPTION THE PARTAS DESCRIBED ABOVE.
Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or
consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State
to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or
obligation in connection with this Part.
920-0007 2009-09
This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select
vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no
circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any
consequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, nor
will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data
bus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of this
product be liable for consequential damages sustained in connection with this product and neither assumes nor authorizes
any representative or other person to assume for it any obligation or liability other than the replacement of this product only.
Protected by U.S. Patents: 5,719,551; 6,011,460 B1 *; 6,243,004 B1; 6,249,216 B1; 6,275,147 B1; 6,297,731 B1; 6,346,876
B1; 6,392,534 B1; 6,529,124 B2; 6,696,927 B2; 6,756,885 B1; 6,756,886 B2; 6,771,167 B1; 6,812,829 B1; 6,924,750 B1;
7,010,402 B1; 7,015,830 B1; 7,031,826 B1; 7,046,126 B1; 7,061,137 B1; 7,068,153 B1; 7,205,679 B1; Cdn. Patent:
2,320,248; 2,414,991; 2,415,011; 2,415,023; 2,415,027; 2,415,038; 2,415,041; 2,420,947; 2,426,670; 2,454,089; European
Patent: 1,053,128; Pat. Pending: 2,291,306. Made in Canada.
Additional information can be found at:
www.xpresskit.com
www.directechs.com
© 2012 Directed. All rights reserved.