Aiwa | TV-F2500 | Service manual | Aiwa TV-F2500 Service manual

TV-F2400
TV-F2500
U
NH,HT
SERVICE MANUAL
COLOR TELEVISION
S/M Code No. 09-009-431-9S2
SU
PP
LE
ME
DA
NT
TA
• This Service Manual contains the additional information "NOTE ON BEFORE
REPAIRING", "SETTING OF IIC BUS DATA" and "ADJUSTMENT" for the model
TV-F2400/2500(U,NH,HT). If requiring the other information, see Service Manual
of TV-F2400(U),(S/M Code No. 09-007-431-9R1) and TV-F2500(NH,HT),
(S/M Code No. 09-008-431-9R2).
NOTE ON BEFORE REPAIRING
•
•
•
Do not turn on the power without degaussing coil when repairing.
In case of removing degaussing coil when repairing, connect dummy as follows;
Method 1 : Use another new degaussing coil and connect it when repairing.
Method 2 : Place the 6.8 - 2.0W resistor to the degaussing coil connector and connect it
as service jig.
Cement resistor R848 ,which is parallel to the degaussing coil, is opened when the power is turned
on without the degaussing coil or dummy resistor.
–2–
Setting of IIC BUS Data
This model is designed with the ability to adjust most parts of the image
projection and deflection system by using the jig remote controller.
Preparations :
•
Modify the hidden keys on the RC-6VT06 jig remote controller
(TV-C142/86-LB4-951-010) so that they can easily be pressed.
2 keys to be modified. (Refer to the below illustration)
Starting the “Service Mode” :
Hidden key / “TEST”
• Press the “TEST” key on the jig remote controller once to enter to the
“Aging Mode” (Refer Fig. 1).
• Press the “TEST” key on the jig remote controller again to enter the
“Adjustment Mode”.
Hidden key / “FINISH”
• The accumulated hours in the “Aging Mode” will be reset by pressing
the “FINISH” key on the jig remote controller.
• Avoid to press this key during general repairs.
AGING AFT OK 0000H US25
Fig.1a
Aging Mode Operation Method :
Make sure that confirmation is done after replacing the EEP ROM.
<TV-F2400>
AGING AFT OK 0000H NH25
1. Enter to the aging mode by pressing the “TEST” key on the remote
controller. (Fig. 1a)
Fig.1b
2. Press “SYSTEM” key and confirm the condition of the distinction
switch. (Fig. 2a)
Confirm the following items before doing the electrical adjustment.
• In case the contents are different, press “5” key and select [US25]
for the destination.
• In case the data is different use the “CHANNEL” key to scroll
through 0~F and set to the correct data value of “0” or “1” by the
volume key.
• All the settings are stored when the “TEST” key is pressed to
complete the correction.
1
2
3
4
5
6
US21
TW21
NH21
NH25
US25
TW25
Fig.2a
<TV-F2500>
1. Enter to the aging mode by pressing the “TEST” key on the remote
controller. (Fig. 1b)
2. Press “SYSTEM” key and confirm the condition of the distinction
switch. (Fig. 2b)
Confirm the following items before doing the electrical adjustment.
• In case the contents are different, press “4” key and select [NH25]
for the destination.
• In case the data is different use the “CHANNEL” key to scroll
through 0~F and set to the correct data value of “0” or “1” by the
volume key.
• All the settings are stored when the “TEST” key is pressed to
complete the correction.
–3–
1
2
3
4
5
6
US21
TW21
NH21
NH25
US25
TW25
Fig.2b
Contents of Aging Mode :
1. Release “Auto Power Off” function
Release “Auto Power Off” function when no input is supplied.
Use this mode for warming up (aging) during CRT adjustment.
2. AFT S-curve status indication
The condition of FT S-curves are indicated by “OK” for suitable tuning, “UP” for too high or “DN” for too low.
3. Display of “CRT ON” accumulated hours
The CRT usage time is accumulated on an hourly basis and is displayed in
hexadecimal figures.
Sample calculation of displayed hexadecimal figures: AFT OK 1234 H US25
• The display will be reset to 0000H when the accumulated hours exceed
7FFFH(32768 hours).
–4–
Adjustment Mode Operation Method :
1. Return to the aging display by pressing the “SYSTEM” key and press “TEST” key to display the adjustment menu screen.
PAGE 1
1 H POS
2 V POS
3 V SIZE
4 OSD POS
5 PIF VCO
6 RF AGP
00
00
00
00
00
00
PUSH
1~6 KEY
PAGE 2
1 R CUTOFF
2 G CUTOFF
3 B CUTOFF
4 G DRIVE
5 B DRIVE
00
00
00
00
00
0~31
R CUTOFF
0~7
V SIZE
0~255
G CUTOFF
0~63
PAGE 4
1 358 TRAP
2 BPF
3 H AFC
4 WPL
00
00
00
00
PUSH
1~4 KEY
Press "MENU"
key to return
PAGE 2
V POS
00
00
00
00
PUSH
1~4 KEY
Press "MENU"
key to return
H POS
CONTRAST
BRIGHT
TINT
COLOR
PIF VCO 58
RF AGC 32
PUSH
CH UP/DN KEY
*
*
0~48
SD OK
AFT OK
00
00
00
B CUTOFF
0~255
Press "MENU"
key to return
Press "MENU"
key to return
PAGE 3
PAGE 4
SUB CONTR...-63~+63
358 TRAP
SUB BRIGHT -63~+63
0~255
PUSH
1~3 KEY
G DRIVE
B DRIVE
0~255
SUB TINT
-63~+63
SUB COLOR -63~+63
WPL
0~255
Press "MENU"
key to return
PAGE 5
D:ON
ATT
1:OFF
BPF CUTOFF 2:AUTO
H AFC
OSD POS
PAGE 4
1 ATT
2 SPECTRAL
3 WIDEBAND
ENTER CONTRAST
PUSH
1~5 KEY
PAGE 1
PAGE 3
1 SUB
2 SUB
3 SUB
4 SUB
10
SPECTRAL
0: +2
1: +1
WIDEBAND
0: OFF
1: ON
SD OK
PUSH
CH UP/DN KEY
PUSH
CH UP/DN KEY
PUSH
CH UP/DN KEY
PUSH
CH UP/DN KEY
Each figure in the adjustment menu can be changed using the volume adjustment keys (+, —).
Though the "MENU" contents will disappear once "MUTE" key were pressed while operating on "MENU" screen, it will reappear by pressing "O" key.
Fig.3
–5–
31
31
ADJUSTMENT
Electrical adjustment:
•
•
Operate after inputting the following initial figures when replacing EEP ROM.
Check the condition and adjust the area where the general repair is carried out.
Initial Value
PAGE 1
1.
H POS
2.
V POS
3.
V SIZE
4.
OSD POS
5.
PIF VCO
6.
RF AGC
16
3
30
6
58
32
PAGE 2
1.
R CUT OFF
2.
G CUT OFF
3.
B CUT OFF
4.
G DRIVE
5.
B DRIVE
127
127
127
127
127
PAGE 3
1.
SUB
2.
SUB
3.
SUB
4.
SUB
–5
+ 32
+ 16
+ 16
CONTRAST
BRIGHT
TINT
COLOR
PAGE 4
1.
3.58 TRAP
2.
BPF
3.
H AFC
4.
WPL
Specific Value
OFF
AUTO
+1
OFF
PAGE 5
1.
ATT
2.
SPECTRAL
3.
WIDEBAND
10
24
44
PWB Adjustment / Do before entering the adjustment mode
1.
H SIZE Horizontal Size Crosshatch
6~7
Input Signal : Crosshatch
Adjustment Point : SFR601
Measuring Instrument : Pattern generator / reader: LCG-401
Center
• Use SFR601 to adjust the dot mark of the crosshatch to the center.
(So that the number of measure become the same horizontally and vertically)
6~7
2.
PIN & BARREL Pin Phase & Pin Amplitude (Barrel) Adjustment (Linearity).
Fig. A
Input Signal : Crosshatch
Adjustment Point : SFR602 / PIN (Fig. A)
SFR603 / BARREL (Fig. B)
Measuring Instrument : Pattern generator / reader: LCG-401
• Adjust the crosshatch distortion.
1. Use SFR602 to adjust the vertical distortion (Fig. A).
2. Use SFR603 to adjust the horizontal distortion (Fig. B).
• Repeat 1~2 until the vertical lines become straight.
Fig. B
Crosshatch signals are not illustrated
–6–
PAGE 1
8~9
1-1. H POS Horizontal Positioning Adjustment / Adjustment Menu Screen: PAGE 1-1
Center
8~9
PAGE 1
Input Signal : Crosshatch
Measuring Instrument : Pattern generator / reader: LCG-401
• Use the volume keys on the jig remote controller to adjust the dot mark in the centre of
crosshatch screen to the exact centering position by allocating an equal number of squares
on the left and right side of the dot. (Fig. 1-1)
H POS
20
Fig. 1-1
1-2. V POS Vertical Positioning Adjustment / Adjustment Menu Screen: PAGE 1-2
Input Signal : Crosshatch
Measuring Instrument : Pattern generator / reader : LCG-404
PAGE 1
• Using the volume keys on the jig remote controller to adjust the
dot mark to the exact vertical centre position in the crosshatch screen.
(Fig. 1-2)
CRT center
mark
V POS
2
Fig. 1-2
V LINEARITY Vertical Linearity Adjustment
Input Signal : Monoscope (LION MARK)
Measuring Instrument : Monoscope / NTSC
Use the volume key on the jig remote controller to adjust the 6 circular figures on
monoscope to be true circles.
<Simple Adjustment>
Input Signal : Crosshatch
Adjustment Location : SFR501
Measuring Instrucment : Pattern generator / NTSC
Adjust SFR501 so that the crosshatch patterns is square.
* Adjust V POS (PAGE 1-2) and Linearity repeatedly. If it does not work, adjust V Size
(PAGE 1-3) first and try the adjustment again.
1-3
V SIZE Vertical Size Adjustment / Adjustment Menu Screen : PAGE 1-3
Input Signal : Crosshatch
Measuring Instrument : Pattern generator / reader : LCG-401
PAGE 1
• Use the volume keys on the jig remote controller to adjust the number of
the squares of the crosshatch pattern to 13~14. (Fig. 1-3)
13 ~ 14
Squares
18
V POS
Fig. 1-3
–7–
1-4. OSD POS OSD Positioning Adjustment / Adjustment Menu Screen: PAGE 1-4
PAGE 1
Input Signal: Not specified.
• Use the volume keys on the jig remote controller to adjust the position of the +
sign on both right and left sides shown on the OSD screen to be equivalent from
the screen edge. A=B Fig. 1-4
+
OSD POS 24
+
A
B
Fig. 1-4
1-5. PIF VCO Video IF/ VCO Adjustment / Adjustment Menu Screen: PAGE 1-5
Input Signal: ANT RF-INPUT
Colour Bar
Measuring Instrument: Oscilloscope Pattern generator / reader: LCG-401
PA G E 1
• Use the volume keys on the jig remote controller to adjust the status of AFT on the
screen to “OK”. Fig. 1-5
• If “OK” status can be obtained from multiple numbers of ranges, select the
intermediate value.
* SD will display “NG” while the screen has no signals. There will be no problem with
VCO Adjustment. (e.g. when there is no signal with Video input) In this case, it is
possible to make adjustments as long as ANT is loaded.
SD
PIF VCO
58
OK
AFT
OK
AFT
OK
Fig. 1-5
1-6. RF AGC RF-AGC/ Adjustment Menu Screen: PAGE1-6
Input Signal: ANT RF-INPUT
Color Bar
Test Point: TP101 RF AGC
Measuring Instrument: Oscilloscope
Pattern generator / reader: LCG-401
PA G E 1
1. Connect the oscilloscope to TP101.
2. Using the volume keys on the jig remote controller to adjust the test point voltage
value to 4.0 ± 0.5VDC. Then check if the status of AFT on the Adjustment Menu
Screen is displayed “OK” as shown in Fig. 1-6.
RF AGC
32
Fig. 1-6
–8–
PAGE 2
White Balance Adjustment : Adjustment Menu Screen: PAGE 2-1~5
*User’s picture quality will be cleared when the adjustment menu screen appears.
Input signal : White raster
Contents of Adjustment : 1. R CUT OFF
Contents of Adjustment : 2. G CUT OFF
Contents of Adjustment : 3. B CUT OFF
Contents of Adjustment : 4. G DRIVE
* More than 20 minutes of aging is required
5. B DRIVE
before the adjustment.
Contents of Adjustment
* The whole process should be repeated
several times for the adjustment.
Measuring instrument : Pattern generator / reader: LCG-401
PAGE 2 PAGE 2
R CUTOFF
0~255
G CUTOFF
0~255
R CUTOFFB CUTOFF 127
0~255
G DRIVE
G CUTOFF
B CUTOFF
G DRIVE
B DRIVE
Cut Off Adjustment :
0~255
127
B DRIVE
0~255
127
127
127
Fig. 2-1
2-1. Use the pattern generator to input the white raster signal.
2-2. Using the volume keys on the jig remote controller, fix the figure of the strongest color on the screen to 127 and adjust the other 2 cut off
figures until white picture appears on the screen.
Drive Adjustment :
2-3.
2-4.
2-5.
2-6.
2-7.
Using the volume keys on the jig remote controller, bring the figure of the 4.G DRIVE up to more than 200 till the color becomes greenish.
Then reduce the numeric figure to the point where the greenish color disappears completely.
Using the volume keys on the jig remote controller, bring the figure of the 5.B DRIVE up to more than 200 till the color becomes bluish.
Then reduce the numeric figure to the point where the bluish color disappears completely.
Repeat the process of 1~6 for several times and adjust for whiter look.
Focus Adjustment :
Input Signal : Dot pattern
Adjustment Point : SFR located at upper part of FBT (T601)
Measuring Instrument : Pattern generator / reader: LCG-401
• Adjust SFR which is located at upper part of FBT (T601) in order to get the best focus for
the dot.
Screen Adjustment :
Input Signal : No Signal (No Raster)
Adjustment Point : SFR located at lower part of FBT (T601)
Measuring Instrument : Pattern generator / reader: LCG-401
1. Enter to “ Aging Mode Screen” by pressing “ TEST” key on the jig remote controller
once.
2. Press “10” key of the numeric channal keypad to get a horizontal single line screen (Fig.2-2).
3. Adjust SFR located at lower part of FBT (T601) until the horizontal line starts to be slightly brightened.
4. Repeat the process of step 2 and return to the “Adjustment Menu Screen”.
PAGE 3
Fig. 2-2
PAGE 2
3-1. SUB BRIGHT Sub-brightness Adjustment / Adjustment Menu Screen: PAGE3-2
(careful with the order)
Input Signal: Color Bar (Stair step)
Measuring Instrument: Pattern generator / reader: LCG-401
• Using the volume keys on the jig remote controller to adjust the scale of the second last
from right to be slightly brightened.
35
SUB BRIGHT
Fig. 3-1
–9–
3-2. SUB CONTRAST Sub-contrast Adjustment / Adjustment Menu Screen:
PAGE 3-1
Input Signal: Color Bar (QIW)
croma/OFF
Measuring Instrument: Oscilloscope Pattern generator / reader:
105+2.0V
75%White
Test Point: S0901 R(R CATHODE)
100%White
1. Connect the oscilloscope to S0901 R.
2. Using the volume keys on the jig remote controller adjust
the pedestal level and the voltage of 100% white to 105 ± 2.0V,
according to Fig. 3-2.
Fig. 3-2
3-3. SUB TINT Sub-Tint Adjustment / Adjustment Menu Screen: PAGE 3-3
Magenta
Input Signal: Color Bar (VIDEO IN)
Measuring Instrument: Oscilloscope / Pattern generator / reader:
LCG4-1
Test Point: CNA704 3 PIN B
BLUE
1. Connect the oscilloscope to CNA704 3 PIN B .
2. Using the volume keys on the jig remote controller, a
djust the top excursions of waveform “Magenta” and “Blue” to be linear
(Fig. 3-3).
Fig. 3-3
3-4. SUB COLOR Sub-color Adjustment / Adjustment Menu Screen: PAGE3-4
Input Signal: Color Bar (VIDEO IN)
Measuring Instrument: Oscilloscope / Pattern generator / reader:
LCG-401
Test Point: CNA704 3 PIN B
Cyan
Magenta
Horizontal
Line
1.0V
10µS
1. Connect the oscilloscope to CNA704 3 PIN B .
2. Using the volume keys on the jig remote controller,
adjust the top excursions of waveform to be linear (Fig. 3-4).
Fig. 3-4
PAGE 4
4.
TV SETTING CHECK Confirmation of Model Setting /
Adjustment Menu Screen: PAGE4-1~4
PAGE 4
Each setting is particular to each model. Do not make any changes to these fixed setting.
• Check if the details of the Adjustment Menu Screen are the same as those in Fig. 4.
If they were different, readjust them accordingly using the volume keys on the jig remote
controller.
3.58 TRAP
BPF
H AFC
WPL
*
(Non-operational)
1 358 TRAP
0: ON
2 BPF CUTOFF
0 : ON
2 : AUTO
1 : +1
0 : OFF
3 H AFC
4 WPL
2: AUTO
1: +1
0: OFF
Enable to check on the menu list
Fig. 4
The details of 3.58 TRAP cannot be controlled.
– 10 –
PAGE 5
5-1. ATT ALIGNMENT ATT Adjustment / Adjustment Menu Screen: PAGE 5-1
PAGE 5
Input Signal: ANT RF-INPUT / Color Bar
Measuring Instrument: Oscilloscope / Pattern generator / reader: LCG-401
Test Point: IC701 2 PIN TV OUT-L
1. Connect the oscilloscope to IC701 2 PIN
2. Using the volume keys on the jig remote controller, adjust the value of IC701 2 PIN
to 490 ± 20mVrms.
10
ATT
Fig. 5-1
5-2. SEPARATION ALIGNMENT Adjustment of Stereo Sound Separation
Degree/Adjustment Menu Screen: PAGE 5-2~3
Input Signal: Setting of TV Multiplex Transmission Signaler
Variation
Internal Variation
Internal
400 Hz
Audio
L ch
Channel
2 ch
Video Signal
Color Bar
Minimum
0.2V
0.5mS
Multiplex Transmission Signaler RF Output / 2CH
Fig. 5-2
Measuring Instrument: Oscilloscope / TV Multiplex Transmission Signaler /
reader: 236A
Test Point: IC701 1 PIN TV OUT-R
PAGE 5
1. Connect the oscilloscope to IC701 1 PIN
2. Start receiving signals from TV 2CH.
3. PAGE5-3
Using the volume keys on the jig remote controller, adjust the voltage width of
IC701 1 PIN waveform to the minimum as in Fig 5-3.
WIDE BAND
31
Fig. 5-3
PAGE 5
4. Adjust the internal Variation of TV Multiplex Transmission Signaler to
1kHz and perfrom the same method as in step 3. (Fig 5-4)
5. Repeat the step 3~4 for several times to adjust for the minimum value.
SPECTRAL
31
Fig. 5-4
– 11 –
TUNER ADJUSTMENT
If adjustment elements were replaced for repair, conduct the following set of adjustments. And then, further adjustments should be conducted on the
Adjustment Menu Screen.
If this set of adjustments was not completed, no further adjustments on the Adjustment Menu Screen can be conducted.
The elements whose circuit condition will be altered depending on repair.
• VCO coil
• SIF coil
6-1.
VCO ADJUSTMENT VCO (PIF) Adjustment / Video Transfer Frequency Free-Running Adjustment
Input Signal: RF-Color Bar
Input Level: 90dBµ V
BROADCAST CH/fc=45.75MHz
MODE: TUNER
Test Point: IN-PUT / TU101-11PIN IF
OUT-PUT / IC301-44PIN AFT
Measuring Location: L205/P-IF
Measuring Instrument: Oscilloscope / Pattern generator / reader: LCG401
1. Connect the oscilloscope to IC301-44PIN.
2. Enter the specific level of RF signal to TU101-11PIN, and adjust L205 so that the voltage of IC301-44PIN will be 2.8±0.2VDC.
6-2. SIF ADJUSTMENT Audio IF Variation Adjustment
Input Signal: AM/FM-SG RF OUT/4.5MHz-SIF
MOD OFF
90dB µV
4.5V
• The simple way to make adjustment is to receive a normal broadcasting.
MODE: TUNER
Test Point:
IN-PUT/IC301-52PIN SIF
OUT-PUT/IC301-54PIN FM DET
Measuring Location: L201/S-IF
Measuring Instrument: Oscilloscope
Am/FM-Signal Generator
1. Connect the oscilloscope to IC301-54PIN.
2. Enter the specific signal to IC301-52PIN, and adjust L201 so that the voltage
of IC301-54PIN will be 4.5 ± 0.2VDC.
– 12 –
Fig.6-1.
2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111
9620450
Printed in Singapore
Download PDF