RANGE MODELS: ER30D, ER36D AND ER48D

RANGE MODELS: ER30D, ER36D AND ER48D
Trim Replacement Kit
AERTK30, AERTK36, AERTK48
DANGER:
INSTALLATION
INSTRUCTIONS
Electric shock hazard! Before installation, disconnect power
at the circuit breaker or fuse box.
WARNING: To avoid burns, do not disassemble the range until it has cooled.
WARNING: To avoid personal injury, wear safety glasses during installation.
CAUTION: To prevent damage to the range, use only the tools indicated in these instructions.
NOTE: It is not necessary to pull the range out from the wall to change the trim color.
Use these instructions to change the trim color on the ER30D, ER36D and ER48D series ranges.
Tools Required
•
•
•
Kit Part Number Identification
Phillips Head Screwdriver (4-40)
AERTKXXYY
Torx Driver (T20)
2 Clamps
Range Size
Trim Color
CH = Chrome
CP = Copper
BR = Brass
BC = Black Chrome
Parts included with this kit
Door End Caps
30 and 36-Inch Ranges (2)
48-Inch Ranges (4)
Trim Rings
30-Inch Ranges (4)
36 and 48-Inch Ranges (6)
Range End Caps (2)
Extra Screws
Part #
83571
Part #
101505
Part #
83669
Part #
100385
Screw Part #
Use
ER30D
ER36D
ER48D
101505
End Caps
2
2
2
83571
Trim Rings
12
18
18
2
2
4
83669
Handle End Caps
100385
Handle Mounting
100026
Handle Mounting
Quantity
2
2
4
Part #
100026
Part No. 101516 Rev. E
Trim Kit Installation Instructions
STEP 1: Disconnect power to the range at the junction or fuse
box.
Trim Ring Replacement
STEP 2: Remove the knobs. Pull straight out to
remove them. Put them in a safe place to
prevent damage.
LED
IMPORTANT: To prevent the parts behind the control
panel from being misaligned, remove only one trim ring
at a time.
STEP 3: Remove the three (3) Phillips head screws
that hold the existing trim ring in place. Note
the position of the blue LED light located
behind the trim ring.
Trim Ring
Knob
Screws
STEP 4: While making sure the LED remains in
place, put the new trim ring into position.
Tighten it in place with the three (3) Phillips
head screws.
STEP 5: Repeat steps 3 and 4 for the remaining trim rings.
STEP 6: After all the trim rings are replaced, check to make
sure they are all properly aligned, that the LEDs
are in the proper place, and that the screws are
tightened.
STEP 7: Attach the knobs. Align the “D-shaped” opening on
the back of the knob with the end of the valve shaft.
Carefully push the knob on until it stops.
For Models ER36D and ER48D, put the knobs with
the words “MAX GRIDDLE” on them on the inner
(center burner) valve shafts.
For ER30D, place the “MAX GRIDDLE” knobs in
the 2 right hand valve shafts. Put the remaining
knobs on the remaining valve shafts.
CAUTION: To prevent damage to the griddle included with the range or
the optional grill, do not install the griddle knobs in the wrong position!
ER30D
ER36D and ER48D
Page 2
Trim Kit Installation Instructions
Range End Cap Replacement
STEP 8: Locate the right end cap screw access
hole under the right side of the front
panel overhang. Remove the 4-40 X
1/2 phillips head screw.
End Cap
STEP 9: Pull the end cap out of the side of the
range to remove it. Insert the new end
cap in its place.
STEP 10: Thread the end cap screw and tighten
by hand. Do not over-tighten.
STEP 11: Repeat sets 8 - 10 for the left end cap.
Access Hole
Door End Cap Replacement
Screw
STEP 12: Open the oven door to the horizontal
position.
STEP 13: On model ER30D and ER48D, to prevent damage to the
door glass and door: Firmly tape or clamp both sides of the
door three (3) inches from the top to prevent it from coming
apart when the handle screws are removed. CAUTION: Do not
overtighten. Damage may occur. If clamps are used, pad both
sides of the clamp to prevent damage to the door surfaces.
STEP 14: On model ER36D: Remove the two (2) door screw
covers.
STEP 15: Grasp the handle with one hand and remove the two (2) torx
screws that hold it in place.
Screw,
2 places
Clamp
Pad
Clamp
Pads
Handle
Screw cover
2 places
Handle
ER30D and ER48D
ER36D
Page 3
STEP 16: Remove the two (2) torx screws from the bottom of the
handle.
STEP 17: Pull the end caps off the end of the handle and replace
them with the new ones.
STEP 18: Thread the two (2) torx head screws into the handle and
tighten them into place. CAUTION: Do not overtighten.
Tighten only by hand.
End Cap,
2 places
Screw,
2 places
Handle
STEP 19: Line up the screw holes on the handle with the mounting
holes on the oven door. Make sure the screws that hold the
end caps in place face toward the bottom of the door.
STEP 20: Thread the two (2) screws through the door and into
the handle. Tighten them into place. Do not overtighten.
Damage to the door or the door glass may result.
STEP 21: On model ER36D: Replace the screw covers.
STEP 22: Remove the clamps or tape from the door.
Dacor ● 600 Anton Blvd. Suite 1000 Costa Mesa, CA 92626 ● Phone: (800) 793-0093 ● Fax: (626) 403-3130 ● www.Dacor.com