223
WELLS BLOOMFIELD, LLC
10 Sunnen Dr., St. Louis, MO 63143
telephone: 314-678-6314
fax: 314-781-2714
www.wells-mfg.com
OWNERS MANUAL
for
COUNTERTOP
CERAMIC
HOTPLATES
Models:
HC100
HC125
HC225
Model HC225
Includes
INSTALLATION
USE & CARE
EXPLODED VIEW
PARTS LIST
WIRING DIAGRAM
IMPORTANT: DO NOT DISCARD THIS MANUAL
This manual is considered to be part of the appliance and is to be given to the OWNER or
MANAGER of the restaurant, or to the person responsible for TRAINING OPERATORS of
this appliance. Additional manuals are available from your WELLS DEALER.
THIS MANUAL MUST BE READ AND UNDERSTOOD BY ALL PERSONS USING OR
INSTALLING THIS APPLIANCE. Contact your WELLS DEALER if you have any
questions concerning installation, operation or maintenance of this equipment.
p/n 2M-303755 Rev. D
M223
120120
LIMITED WARRANTY STATEMENT
Unless otherwise specified, all commercial cooking
equipment manufactured by WELLS BLOOMFIELD, LLC is
warranted against defects in materials and workmanship for
a period of one year from the date of original installation or
18 months from the date of shipment from our factory,
whichever comes first, and is for the benefit of the original
purchaser only.
THIS WARRANTY IS THE COMPLETE AND ONLY
WARRANTY, EXPRESSED OR IMPLIED IN LAW OR IN
FACT, INCLUDING BUT NOT LIMITED TO, WARRANTIES
OF MERCHANTABILITY OR FITNESS FOR ANY
PARTICULAR PURPOSE, AND/OR FOR DIRECT,
INDIRECT OR CONSEQUENTIAL DAMAGES IN
CONNECTION WITH WELLS BLOOMFIELD PRODUCTS.
This warranty is void if it is determined that, upon inspection
by an authorized service agency, the equipment has been
modified, misused, misapplied, improperly installed, or
damaged in transit or by fire, flood or act of God. It also
does not apply if the serial nameplate has been removed, or
if service is performed by unauthorized personnel. The prices charged by Wells Bloomfield for its products are based
upon the limitations in this warranty. Seller’s
obligation
under this warranty is limited to the repair of defects without charge by a Wells Bloomfield factory
authorized
service agency or one of its sub-service
agencies. This
service will be provided on customer’s premises for nonportable models. Portable models (a device with a cord
and plug) must be taken or shipped to the closest authorized service agency, transportation charges prepaid, for
service. In addition to restrictions contained in this warranty, specific limitations are shown in the Service Policy and
Procedure Guide. Wells Bloomfield authorized service
agencies are located in principal cities. This warranty is
valid in the United States and Canada and void elsewhere.
Please consult your classified telephone
directory, your
foodservice equipment dealer or contact:
Wells Bloomfield, LLC
10 Sunnen Dr., St. Louis MO 63143 USA
phone (314) 678-6314 or fax (314) 781-2714
for information and other details concerning warranty.
SERVICE POLICY AND PROCEDURE GUIDE and ADDITIONAL WARRANTY EXCLUSIONS
1.
2.
3.
4.
6.
cleaning schedules, are customer responsibility. Those
miscellaneous adjustments noted are customer
responsibility. Proper attention to preventative
maintenance and scheduled maintenance procedures
will prolong the life of the appliance.
7. Travel mileage is limited to sixty (60) miles from an
Authorized Service Agency or one of its sub-service
agencies.
8. All labor shall be performed during regular working
hours. Overtime premium will be charged to the buyer.
9. All genuine Wells replacement parts are warranted for
ninety (90) days from date of purchase on nonwarranty equipment. This parts warranty is limited only
to replacement of the defective part(s). Any use of
non-genuine Wells parts completely voids any
warranty.
10. Installation, labor, and job check-outs are not
considered warranty and are thus not covered by this
warranty.
11. Charges incurred by delays, waiting time or operating
restrictions that hinder the service technician’s ability to
perform service are not covered by warranty. This
includes institutional and correctional facilities.
SHIPPING DAMAGE CLAIM PROCEDURE
NOTE: For your protection, please note that equipment in
this shipment was carefully inspected and packaged by
skilled personnel before leaving the factory. Upon
acceptance of this shipment, the transportation company
assumes full responsibility for its safe delivery.
IF SHIPMENT ARRIVES DAMAGED:
1. VISIBLE LOSS OR DAMAGE: Be certain that any
visible loss or damage is noted on the freight bill or
express receipt, and that the note of loss or damage is
signed by the delivery person.
2. FILE CLAIM FOR DAMAGE IMMEDIATELY:
Regardless of the extent of the damage.
3.
CONCEALED LOSS OR DAMAGE: if damage is
unnoticed until the merchandise is unpacked, notify the
transportation company or carrier immediately, and file
“CONCEALED DAMAGE” claim with them. This
should be done within fifteen (15) days from the date
the delivery was made to you. Be sure to retain the
container for inspection.
Wells Bloomfield cannot assume liability for damage or loss
incurred in transit. We will, however, at your request, supply
you with the necessary documents to support your claim.
xi
223 p/n 2M-303755 Owners Manual Counter Top Ceramic Hotplates
5.
Resetting of safety thermostats, circuit breakers, over
load protectors, and/or fuse replacements are not
covered by this warranty unless warranted conditions
are the cause.
All problems due to operation at voltages or phase
other than specified on equipment nameplates are
not covered by this warranty.
Conversion to correct voltage and/or phase must be
the customer’s responsibility.
All problems due to electrical connections not made
in accordance with electrical code requirements
and wiring diagrams supplied with the equipment are
not covered by this warranty.
Replacement of items subject to normal wear, to
include such items as knobs, light bulbs; and, normal
maintenance functions including adjustments of
thermostats, adjustment of micro switches and
replacement of fuses and indicating lights are not
covered by warranty.
Damage to electrical cords and/or plug due to exposure
to excessive heat are not covered by this warranty.
Full use, care, and maintenance instructions supplied
with each machine. Noted maintenance and
preventative maintenance items, such as servicing and
TABLE OF CONTENTS
WARRANTY
xi
SPECIFICATIONS
1
FEATURES & OPERATING CONTROLS
2
PRECAUTIONS & GENERAL INFORMATION
3
INSTALLATION
4
OPERATION
5
CLEANING INSTRUCTIONS
6
SPECIAL CARE INSTRUCTIONS
7
TROUBLESHOOTING
8
EXPLODED VIEW & PARTS LIST
9-14
WIRING DIAGRAM
15-16
PARTS & SERVICE
21
CUSTOMER SERVICE DATA
21
Thank You for purchasing this
Wells Bloomfield appliance
Proper installation, professional
operation and consistent
maintenance of this equipment
will ensure that it gives you the
very best performance and a long,
economical service life.
This manual contains the
information needed to properly
install this equipment, and to use
and care for the equipment in a
manner which will ensure its
optimum performance.
SPECIFICATIONS
223 p/n 2M-303755 Owners Manual Counter Top Ceramic Hotplates
MODEL ELEMENT
WIDTH
DEPTH VOLTS
AMPS
kW
PLUG
11.7 A
1.4 kW
NEMA 5-15P
1”
208 V 1ø 9.0 A
1.9 kW
NEMA 6-15P
1”
240 V 1ø 10.4 A
2.5 kW
NEMA 6-15P
1”
24-5/8” 208 V 1ø 18.1 A
3.8 kW
NEMA 6-30P
1”
240 V 1ø 20.8 A
5.0 kW
NEMA 6-30P
1”
HC100
Single 7”
12-5/8”
12-5/8” 120 V
HC125
Single 9”
14-3/4”
14”
HC225
Dual 9”
14-3/4”
LEG
HEIGHT
SPECIFICATIONS — EXPORT MODELS
MODEL
ELEMENT
WIDTH
HC125EU
Single 9”
14-3/4”
HC225EU
Dual 9”
14-3/4”
DEPTH
VOLTS
AMPS
kW
14”
220-240V 1ø
10.4 A
2.5 kW
1”
24-5/8”
220-240V 1ø
20.8 A
5.0 kW
1”
Refer to the Export Manual for this equipment (p/n 2M-301399) for specific
1
LEGS
information.
FEATURES & OPERATING CONTROLS
HEATING ELEMENT
(UNDER CERAMIC TOP)
CERAMIC TOP
HOT SURFACE
INDICATOR LIGHT
TEMPARATURE
CONTROL KNOBS
POWER
INDICATOR LIGHT
POWER CORD
NAME PLATE
ADJUSTABLE LEGS
Provides smooth, low maintenance heating surface
Heating Element
Provides heat for food preparation
Note: elements located under ceramic top
Hot Surface Indicator
Light
Glows whenever ceramic top is above 150ºF (66ºC)
Temperature Control
Infinite switch to control temperature of heating element
Power Indicator Light
Glows any time temperature control is on
Name Plate
Lists manufacturer, model number and serial number
Also lists voltage and wattage rating
Power Cord
Connects hotplate to electrical power
Adjustable Legs
Provides ventilation under hotplate
Allow hotplate to be leveled
2
223 p/n 2M-303755 Owners Manual Counter Top Ceramic Hotplates
Ceramic Top
PRECAUTIONS AND GENERAL INFORMATION
This appliance is intended for use in commercial establishments
only.
This appliance is intended to prepare food for human consumption.
No other use is recommended or authorized by the manufacturer or its
agents.
Operators of this appliance must be familiar with the appliance use,
limitations and associated restrictions. Operating instructions must be
read and understood by all persons using or installing this appliance.
Cleanliness of this appliance is essential to good sanitation. Read and
follow all included cleaning instructions and schedules to ensure the
safety of the food product.
Disconnect the hotplate from electrical power before performing any
maintenance or servicing.
WARNING:
ELECTRIC SHOCK
HAZARD
All servicing requiring access
to non-insulated electrical
components must be
performed by a factory
authorized technician.
DO NOT open any access
panel that requires the use of
tools. Failure to follow this
warning can result in severe
electrical shock.
CAUTION:
RISK OF
DAMAGE
DO NOT submerge hotplate in water. DO NOT splash or pour
water over, onto or into controls or wiring.
DO NOT connect and/or
energize this appliance until
all installation instructions are
read and followed. Damage
to the appliance will result if
these instructions are not
followed.
Hotplate must be operated with the supplied legs properly
Installed.
The technical content of this manual, including any wiring diagrams,
schematics, parts breakdown illustrations and/or adjustment
procedures, is intended for use by qualified technical personnel.
223 p/n 2M-303755 Owners Manual Counter Top Ceramic Hotplates
Any procedure which requires the use of tools must be performed by a
qualified technician.
This manual is considered to be a permanent part of the appliance.
This manual and all supplied instructions, diagrams, schematics, parts
breakdown illustrations, notices and labels must remain with the
appliance if it is sold or moved to another location.
This appliance is made in the USA. Unless otherwise noted, this
appliance has American sizes on all hardware.
AGENCY APPROVAL INFORMATION
This unit complies with NSF Standard 4 only if maintained and
operated per the instructions in this manual.
This unit is
USlisted
under E6070.
Export versions (only) of this unit meet
STD 4
standards.
E6070
E6070
3
EXPORT
MODELS
ONLY
INSTALLATION
NOTE: DO NOT discard
the carton or other packing
materials until you have
inspected the appliance for
hidden damage and tested it
for proper operation.
Refer to SHIPPING DAMAGE
CLAIM PROCEDURE on the
inside front cover of this
manual.
CAUTION:
ELECTRIC SHOCK
HAZARD
Carefully remove the hotplate from the carton. Remove all
protective plastic film, packing materials and accessories from the
hotplate before plugging the hotplate into electrical power or otherwise
performing any installation procedure.
Carefully read all instructions in this manual and the Installation
Instruction Sheet packed with the hotplate before starting any
installation.
Read and understand all labels and diagrams attached to the
hotplate.
Carefully account for all components and accessories before
discarding packing materials. Store all accessories in a convenient
place for later use.
SETUP
Supplied legs must be properly installed.
Setup the hotplate only on a firm level surface. Non-combustible
material (e.g. metal, terrazzo) is recommended.
Maintain at least 1” from adjacent surfaces.
ELECTRICAL
Refer to the nameplate. Verify the electrical service power. Voltage
and phase must match the nameplate specifications. Connecting the
hotplate to the wrong voltage can severely damage the equipment or
cause noticeably decreased performance.
Hotplate is equipped with a grounded electric power cord, this cord
must be plugged into a properly grounded electrical receptacle.
IMPORTANT:
Damage due to being plugged
into the wrong voltage or
phase is NOT covered by
warranty
4
223 p/n 2M-303755 Owners Manual Counter Top Ceramic Hotplates
The ground prong of the power
cord is part of a system
designed to protect you from
electric shock in the event of
internal damage to the
appliance.
NEVER CUT OFF THE
GROUND PRONG
(large round prong).
NEVER TWIST A PRONG TO
FIT AN EXISTING
RECEPTACLE.
Contact a licensed electrician
to install an electrical
receptacle appropriate to
the voltage and amperage
requirements of the
hotplate.
UNPACKING & INSPECTION
OPERATION
GENERAL OPERATIONAL NOTES
CAUTION:
Carefully read the description of the hotplate operation on the
specification sheet.
HOT SURFACES
DO NOT attempt to perform any maintenance or service unless the
hotplate is unplugged or disconnected from electrical power.
Exposed surface scan be hot
to the touch and may cause
burns.
DO unplug the hotplate from electrical power or turn the circuit breaker off before cleaning or servicing.
OPERATION
0
OFF
LO
2
223 p/n 2M-303755 Owners Manual Counter Top Ceramic Hotplates
Each heating element can hold up to a 16 quart pot or pan. For
efficient heating of food product, pots and pans should be no more
than 10” in diameter. Maximize the efficiency of the ceramic top by
using flat-bottom pots and pans.
Preserve the luster of the ceramic cook surface by wiping up spills
promptly and by cleaning frequently. Allow the hotplate to cool
completely before cleaning. Use only cook-top cleaning crème on
glass-ceramic cooking surfaces.
Stir thick liquids frequently to maintain a consistent temperature.
5
6
Save energy by turning the temperature control off any time the
hotplate is not in use. The heating elements will provide full heat within 30 seconds, making it unnecessary to leave the unit on during
intermittent use.
5
Cooking Recommendations:
4
The hot surface indicator light will glow any time the ceramic surface
is approximately 150ºF (65ºC) or higher.
3
The power indicator light will glow any time the temperature control is
on.
7
8
Each heating element is controlled by an infinite switch
temperature control:
OFF removes power from the element
LOW thru 8 are temperature settings
Higher numbers indicate higher temperatures
There is a continuous range of settings between LOW
and HI
HI is a continuous ON setting
Ceramic cooking surfaces
are hot anytime the HOT
SURFACE indicator light is lit.
DO NOT touch the cooking
surface if the HOT SURFACE
light is lit.
I
DO use the supplied scraper to remove burned-on food product.
HOT SURFACES
H
DO NOT use steel wool or abrasive cleansers to clean the ceramic
top.
CAUTION:
IMPORTANT:
The dial markings are an
INDICATION of temperature
only. The temperature of the
food product depends on many
factors, including the size,
shape and material of the food
container, and the quantity and
consistency of the food
product.
CLEANING INSTRUCTIONS
CAUTION:
PREPARATION
ELECTRIC
SHOCK HAZARD
Unplug or disconnect hotplate from electrical power before cleaning.
Allow hotplate to cool completely before cleaning.
Unplug hotplate from electric
power before cleaning.
CAUTION:
BURN HAZARD
Allow hotplate to cool
completely before cleaning.
FREQUENCY
Daily
TOOLS
Cleaning Creme
Razor Scraper
Clean Cloth or Sponge
Mild Detergent or Cleaner Formulated for Stainless Steel
Warm Water
CAUTION:
CLEANING
ELECTRIC SHOCK
HAZARD
Unplug or disconnect hotplate from electrical power before cleaning.
Do not submerge hotplate in
water.
IMPORTANT: DO NOT spill
or pour water into controls,
control panel or wiring.
DO NOT steel wool or
metal scouring pads to clean
ceramic heating surface.
Clean food particles from the ceramic cooking
surface with a razor scraper. Hold the edge
of blade flat against the surface and at a 15º
angle to avoid scratching the ceramic. DO
NOT use metal implements (other than the
razor scraper), steel wool or metal scouring
pads to clean the ceramic cooking surface.
15º
Use only cook-top cleaning creme on glass-ceramic cooking surfaces.
Wipe the ceramic cooking surfaces with cleaning creme and a clean
cloth. The cleaning creme leaves a
protective coating.
Wipe the outer portions of the hotplate cabinet with a clean soft cloth or
sponge dampened with warm water and a mild detergent or cleaner
formulated for cleaning stainless steel. DO NOT use steel wool to
clean hotplate cabinet.
Rinse by wiping hotplate cabinet with a clean soft cloth or sponge
moistened with clean warm water. Dry cabinet by wiping with a clean
soft dry cloth.
6
223 p/n 2M-303755 Owners Manual Counter Top Ceramic Hotplates
DO NOT submerge hotplate
in water. Damage to internal
components will occur.
Damage to internal
components from water
damage is NOT covered by
warranty.
Allow the hotplate to cool until the HOT SURFACE indicator light goes
off before cleaning.
SPECIAL CARE INSTRUCTIONS
DO NOT use the hotplate surface as a cutting board.
CAUTION:
BURN HAZARD
DO NOT cook directly on the glass-ceramic surface.
Check glass and ceramic cookware to verify suitability for use
on hotplates.
DO NOT drop cookware onto glass-ceramic cook surface.
Carefully place heavy pots and skillets on glass-ceramic cook
surface to avoid damage.
Avoid sliding cookware across hotplate surface.
Remove stains and metal marks from the glass-ceramic cook
surface after use by cleaning with cleaning creme. Allow
hotplate surface to cool completely before cleaning
DO NOT leave empty cookware on a hot cooking surface.
Avoid contacting the hot glass-ceramic surface with plastic or
aluminum foil, which may melt.
Allow hotplate to cool
completely before cleaning.
CAUTION:
CUT HAZARD
DO NOT attempt to cook on a
broken hotplate surface.
Severe injury may result.
Contact an Authorized Wells
Service Agency immediately
for repairs.
CAUTION:
CUT HAZARD
223 p/n 2M-303755 Owners Manual Counter Top Ceramic Hotplates
DO NOT attempt to repair a
broken hotplate surface. The
glass-ceramic surface is
impossible to repair
successfully. A broken
surface can cause severe
injury. Contact an Authorized
Wells Service Agency
immediately for repairs.
7
TROUBLESHOOTING
SYMPTOM
POSSIBLE CAUSE
SUGGESTED REMEDY
Hotplate won’t heat
Not plugged in, damaged plug or cord
or circuit breaker tripped
Check plug and cord
Check / reset circuit breaker
One or more sections
won’t heat
Temperature control not on
Turn temperature control to
desired setting
Damaged temperature control,
element or other internal component
Contact Authorized Wells
Service Agency for repairs
Temperature control not set
Adjust for desired temperature
Operating 208/240V unit at 120V
Be sure supply voltage matches nameplate voltage
Damaged temperature control,
element or other internal component
Contact Authorized Wells
Service Agency for repairs
Damaged temperature control,
element or other internal component
Contact Authorized Wells
Service Agency for repairs
Hotplate not hot enough
Hot surface indicator does
not light, or stays on
NOTE: There are no user
serviceable components in this
appliance. In all cases of
damage or component
malfunction, contact your
Authorized Wells Service Agency for repairs.
223 p/n 2M-303755 Owners Manual Counter Top Ceramic Hotplates
8
223 p/n 2M-303755 Owners Manual Counter Top Ceramic Hotplates
NOTES
8
EXPLODED VIEW: HC100
HC-100 COUNTERTOP ELECTRIC CERAMIC HOTPLATE
22328 HC100 COUNTERTOP
CERAMIC HOTPLATE 120VAC
2
1
3
4
6
5
6
18
7
8
LS
L
WE
16
9
10
14
WELLS
13
15
12
11
Model: HC100
Countertop Electric Ceramic Hotplate
PL223
IL1814 Rev. A 7/10/09
9
223 p/n 2M-303755 Owners Manual Counter Top Ceramic Hotplates
17
PARTS LIST: HC100
HC100 COUNTERTOP ELECTRIC CERAMIC
Part No
Qty
Description
WS-501686
1
TOP ASSY HC-100 120V
I7-301686
1
TOP ASSY
2Q-301661
1
GLASS CERAMIC HC100
2H-301213
6FT INSUL LYTHERM HP 1/4X5/8
2J-301121
1
LIGHT SIGNAL CLEAR 120V
2C-31053
11
NUT 8-32 KEPS MS NICKEL
2C-34285
4
SCREW 8-32X3/8 PH 100 FL
2M-300534
1
TRADEMARK DOMED LABEL
2C-33935
2
SCREW 6ABX5/16 PH PAN SMS
2J-70309
1
LIGHT PILOT RED 125V 1/3W
2R-30371
1
KNOB ASSY WARMERS
2C-31697
2
SCREW 8-32X3/16 PH RD HD
D8-30256
1
TRIM RING ASSY
2E-30570
1
SWITCH INFINITE 120V A
2A-41946
4
LEG ADJUST 1IN
2E-70017
1
CORD SET 6FT 5-15P
2K-70215
1
STRAIN RELIEF STR
2N-301660
1
ELEM HC100 120V 1400W
223 p/n 2M-303755 Owners Manual Counter Top Ceramic Hotplates
Fig No
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
10
EXPLODED VIEW: HC125
HC-125 COUNTERTOP ELECTRIC CERAMIC HOTPLATE
22328 HC100 COUNTERTOP
CERAMIC HOTPLATE 120VAC
2
1
3
4
19
6
5
6
18
7
20
8
LS
L
WE
16
9
10
0
OFF
I
8
H
5
6
11
Model: HC100
Countertop Electric Ceramic Hotplate
PL223
IL1814 Rev. B 3/20/14
11
4
12
3
7
WELLS
2
13
15
LO
14
223 p/n 2M-303755 Owners Manual Counter Top Ceramic Hotplates
17
PARTS LIST: HC125
HC-125 COUNTERTOP ELECTRIC CERAMIC
Part No
Qty
Description
WS-501649
1
TOP ASSY REPLACEMENT HC-125
I7-301214
1
TOP DRAWN HC-125 1256
WS-501109
1
GLASS CERAMIC HC-125 1256
2H-301213
6FT
INSUL LYTHERM HP 1/4X5/8
2J-301121
1
LIGHT SIGNAL CLEAR 120V
2C-31053
11
NUT 8-32 KEPS MS NICKEL
2N-301120
1
ELEM 240V 2500W HC-125
2M-300534
1
TRADEMARK DOMED LABEL
2C-33935
2
SCREW 6ABX5/16 PH PAN SMS
2J-31157
1
LIGHT SIGNAL RED
2R-30371
1
KNOB ASSY WARMERS
2C-31697
2
SCREW 8-32X3/16 PH RD HD
D8-30256
1
TRIM RING ASSY
2E-30562
1
SWITCH INFINITE 240V A
2A-41946
4
LEG ADJUST 1IN
2E-35540
1
CORD SET 6-15P 16/3W 4FT
2C-34285
4
SCREW 8-32X3/8 PH
2K-70215
1
STRAIN RELIEF STR HEYCO
I7-301144
1
RETAINER ELEMENT HC-125
I7-301119
1
BRKT ELEMENT HC-125
223 p/n 2M-303755 Owners Manual Counter Top Ceramic Hotplates
Fig No
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
12
EXPLODED VIEW: HC225
HC-225 COUNTERTOP ELECTRIC CERAMIC HOTPLATE
22307 HC-225 COUNTERTOP
CERAMIC HOTPLATE
208/240VAC
2
1
3
4
5
6
21
20
6
7
8
18
17
9
S
LL
WE
10
16
0
0
OFF
OFF
5
6
H
I
H
I
8
7
14
13
3
3
12
4
8
FRONT
2
2
7
LO
LO
REAR
15
11
4
5
6
Model: HC100
Countertop Electric Ceramic Hotplate
PL223
IL1814 Rev. A 7/10/09
13
223 p/n 2M-303755 Owners Manual Counter Top Ceramic Hotplates
19
223 p/n 2M-303755 Owners Manual Counter Top Ceramic Hotplates
PARTS LIST: HC225
Fig No
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
HC-225 COUNTERTOP ELECTRIC CERAMIC
Part No
Qty
Description
2Q-501650
1
TOP ASSY REPLACEMENT HC-225
I7-301215
1
TOP ASSY HC-225
WS-501110
1
GLASS CERAMIC HC-225 & 2256
2H-301213
6FT
INSUL LYTHERM HP 1/4X5/8
2J-301121
1
LIGHT SIGNAL CLEAR 120V
2C-31053
17
NUT 8-32 KEPS MS NICKEL
2N-301120
2
ELEM 240V 2500W
I7-301119
2
BRKT ELEMENT
2M-300534
1
TRADEMARK DOMED LABEL
2C-33935
4
SCREW 6ABX5/16 PH PAN SMS
2R-30583
1
KNOB ASSY FRONT HOTPLATE
2R-30584
1
KNOB RR HP91
2C-31697
4
SCREW 8-32X3/16 PH RD HD
D8-30256
2
TRIM RING ASSY
2E-30562
2
SWITCH INFINITE 240V A
2J-31157
2
LIGHT SIGNAL RED
2E-35259
1
CORD SET 250V 30A 12G 6-30P
2A-41946
4
LEG ADJUST 1IN
2C-34285
4
SCREW 8-32X3/8 PH
2C-35736
1
NUT 8-32 HEX KEPS MS GREEN
2K-45788
1
STRAIN RELIEF SR7W-2 LLF
14
WIRING DIAGRAM
223 p/n 2M-303755 Owners Manual Counter Top Ceramic Hotplates
15
223 p/n 2M-303755 Owners Manual Counter Top Ceramic Hotplates
WIRING DIAGRAM
16
NOTES
223 p/n 2M-303755 Owners Manual Counter Top Ceramic Hotplates
17
223 p/n 2M-303755 Owners Manual Counter Top Ceramic Hotplates
NOTES
18
NOTES
223 p/n 2M-303755 Owners Manual Counter Top Ceramic Hotplates
20
PARTS & SERVICE
DESCRIPTION
SERVICE
PART NO.
SCRAPER, CLEANING
2R-302040
CLEANING CREME, CERAMIC HOTPLATE
2L-301124
IMPORTANT: Use only
factory authorized service
parts and replacement
filters.
For factory authorized
service, or to order factory
authorized replacement parts,
contact your Wells authorized
service agency, or call:
Wells Bloomfield, LLC
10 Sunnen Dr., P.O.Box 430129
St. Louis MO 63143 USA
Service Dept.
phone: (314) 678-6314
fax:
(314) 781-2714
223 p/n 2M-303755 Owners Manual Counter Top Ceramic Hotplates
Service Parts Department can
supply you with the name and
telephone number of the
WELLS AUTHORIZED
SERVICE AGENCY
nearest you.
CUSTOMER SERVICE DATA
please have this information available if calling for service
RESTAURANT _____________________________ LOCATION _____________
INSTALLATION DATE ________________________ TECHNICIAN ___________
SERVICE COMPANY ________________________________________________
ADDRESS ___________________________ STATE ______ ZIP__________
TELEPHONE NUMBER (_____)_____-_________
EQUIPMENT MODEL NO. _______________
EQUIPMENT SERIAL NO. _______________
VOLTAGE: (check one)
120
208
21
240
WELLS BLOOMFIELD, LLC
10 Sunnen Dr., St. Louis, MO 63143
telephone: 314-678-6314
fax: 314-781-2714
www.wells-mfg.com