Agilent Technologies | E3614A | Agilent E36XXA Series Non-Programmable DC Power Supplies

Agilent
E36XXA Series
Non-Programmable DC Power Supplies
Data Sheet
Reliable Power,
Repeatable Results
‡
Linear power supply
‡
Single, dual or triple output
‡
10-turn voltage and current
control
‡
Low noise and excellent
regulation
Affordable, full-featured
benchtop power supplies
provide excellent
performance and flexibility
A whole family of low-cost
power supplies to meet your
needs
The E3600 Series of low-cost
benchtop power supplies give you
the performance of system power
supplies at a decent price. All E3600
family members provide clean power
with excellent regulation and a fast
transient response. The E3600 Series
single-output non-programmable
models are described on this page.
Refer to page 3 for information on
dual-output and triple-output nonprogrammable models.
Single-output models
All E3600 Series single-output
non-programmable power supplies
feature separate digital-panel
meters for monitoring voltage and
current simultaneously, giving
you precise reading and control
capability. All models also feature
10-turn potentiometers for accurate
adjustment of voltage and current
output settings.
With 0.01 percent load and line
regulation, these instruments keep the
output steady when power line and
load changes occur.
The low normal mode noise
specification of less than 200 μVrms
ensures clean power for precision
circuitry.
In all single-output models, either
the positive or negative terminal can
be connected to ground, providing a
positive or negative voltage output.
Outputs can also be floated up to
240 V from ground.
These instruments also feature
adjustable current limits, letting you
set the safest current limit without
having to short the output.
E3610A, E3611A, and E3612A
single-output, dual range
models
These popular 30-watt bench
supplies are designed for general
laboratory use. The constant-voltage,
constant-current output allows
operation as either a voltage or current
source. The changeover occurs
automatically, based on the load.
Each of these models has two ranges,
allowing more current at a lower
voltage. For higher output voltages,
supplies can be connected in series.
These models also feature overload
protection. A continuously acting
constant current circuit protects the
power supply against all overloads
including a direct short placed across
the terminals in a constant voltage
operation.
2
E3614A, E3615A, E3616A and
E3617A models feature
overvoltage protection, remote
sensing and remote
programming
These flexible 60-watt, single-range
power supplies can be used as either
voltage or current sources. When the
output terminal voltage increases to a
preset shut-down level, an overvoltage
protection circuit disables the output
to protect the device under test
(DUT) for damage. The overvoltage
protection feature can be easily
monitored and adjusted from the front
panel.
Using the remote sensing capability,
these instruments automatically
compensate for voltage drop in the
load leads, so you obtain an accurate
voltage at the DUT.
Using the remote analog voltage
programming capability, these
instruments can remotely vary the
voltage, so you are able to control the
regulation output voltage or current.
You can combine multiple units in
auto-parallel, auto-series and autotracking configurations for greater
output voltage or current capacity.
Front and rear output terminals allow
for a flexible configuration. The output
voltage and current can be controlled
with external 0% to 10% volt analog
voltage or variable resistance.
Multiple-output nonprogrammable models
With multiple supplies in a compact
unit, the E3620A and E3630A
provide excellent performance while
saving space on your bench. Both
instruments feature a tight 0.01
percent line and load regulation and a
low normal mode noise specification
of less than 0.35 mV to ensure clean
power for precision circuitry. With a
common mode current specification of
less than 1 μA, both multiple-output
power supplies minimize the power
line current injection.
Like the single-output models in the
E3600 Series, the E3620A and E3630A
feature separate digital panel meters
so you can monitor the voltage and
current simultaneously. They also
protect your DUT against overload and
short-circuit damage.
Smooth turn-on and turn-off
transitions keep power spikes out of
your circuits. Auto-tracking permits
equal or proportional voltage sharing,
and allows control of output voltage
from one master unit. The master and
slave supplies have the same output
polarity with respect to a common bus
or ground. This operation is useful
where simultaneous turn-up, turndown or proportional control of all
power supplies is required.
E3620A dual-output power
supply
The 50-watt E3620A dual-output
power supply provides two 0 V to
25 Vdc outputs with the maximum
current of 1 A to satisfy most bench
requirements. The outputs are
completely independent and isolated.
E3630A triple-output power
supply with auto-tracking
feature
The 35-watt E3630A triple-output
power supply provides three DC
outputs: 0 to 6 V with a maximum
current of 1 to 2.5 A and 0 to 20 V and
0 to %20 V with a maximum current
of 0.5 A. An auto-tracking feature
lets you use one voltage control to
adjust the +20 V and %20 V outputs
simultaneously. The outputs track
each other to within 1 percent, making
it easy to adjust the power supply for
circuits requiring balanced voltages.
Specifications
E3610A
Features
E3611A
E3612A
E3614A
Dual range, 10 turn pots, Constant
Voltage (CV), Constant Current (CC)
modes.
E3615A
E3616A
E3617A
Adjustable overvoltage protection, voltage &
resistance programming, remote sense, rear
outputs, ten turn pots, CV, CC modes. Multiple
supplies can be connected for tracking or higher
power.
Number of outputs
E3620A
E3630A
Isolated
dual
outputs, 10
turn pots
CV, CL
Tracking, CV,
CL (±20 V)
CV, CF (+6 V)
2
3
Number of Output
Ranges
2
2
2
1
1
1
1
1
1
1
DC Output Rating
8 V, 3 A
15 V, 2 A
20 V, 1.5 A
35 V, 0.85 A
60 V, 0.5 A
120 V, 0.25 A
8 V, 6 A
20 V, 3 A
35 V, 1.7 A
60 V, 1 A
25 V, 1 A
25 V, 1 A
+6 V, 2.5 A
+20 V, 0.5 A
%20 V, 0.5 A
Load and Line
Regulation
< 0.01% + 2 mV
Ripple and Noise (20 Hz to 20 MHz)
Normal mode voltage
< 200 μVrms, < 2 mVpp
Normal mode current
< 200 μArms, < 1 mVpp
Common mode current
< 200 μVrms, < 1 mVpp
< 0.02% +
3 mA
< 0.02% +
1.5 mA
< 350 μVrms, < 1.5 mVpp
< 0.02% +
1 mA
< 0.02%
+ 0.5
mA
–
Not specified
Transient Response
Time
< 1 μArms
< 50 μsec following a change in output current from full load to half load for output to recover within:
10 mV
15 mV
Meter Accuracy
±0.5% + 2 counts at 25 ºC ±5 ºC
Meter Resolution
Voltage
10 mV
100 mV
100 mV
10 mV
Current
10 mA
10 mA
1 mA
10 mA
Isolation
10 mA
240 Vdc
3
10 mV
10 mV (0%20 V), 100 mV (>20 V)
1 mA
1 mA
1 mA
10 mA
Supplemental Characteristics
E3610A
E3611A
E3612A
Control Mode
E3614A
E3615A
E3616A
E3617A
CV/CC
E3620A
E3630A
CV/CL
CV/CL (±20 V)
CV/CF (+6 V)
Temperature Coefficient per ºC
Voltage
< 0.02% + 1 mV
Current
< 0.02% + 2 mA
< 0.02% + 500 μV
< 0.02%
+ 3 mA
< 0.02%
+ 1.5 mA
< 0.02%
+ 1 mA
< 0.02% + 1 mV
< 0.02%
+ 0.5 mA
–
Output Drift
Voltage
Current
Less than 0.1% + 5 mV total drift for 8 hours after initial warm-up of 30 minutes
Less than 0.1% + 10 mA total drift for 8 hours after initial warm-up of 30 minutes
N/A
0 to 40 ºC for full rated output. Derate output current 1% per ºC between 40 ºC to 55 ºC
Derate output current 50% between 40 ºC to
55 ºC
Temperature Range
Cooling
Convection cooling
Isolation
±240 Vdc
AC Input
100 Vac ±10%, 47–63 Hz (opt. 0E9)
115 Vac ±10%, 47–63 Hz (std)
230 Vac ±10%, 47–63 Hz (0E3)
Weight
Size
3.8 kg (8.4lbs) net,
4.2 kg (9.3 lbs) shipping
5.5 kg (12.1 lbs) net,
6.75 kg (14.9 lbs) shipping
5.0 kg (11.0 lbs) net, 6.25 kg
(13.8 lbs) shipping
88.1 mm H x 212.3 mm W x 318.4 mm D
3.5” H x 8.4” W x 12.5” D
88.1 mm H x 212.3 mm W x 373.4 mm D
3.5” H x 8.4” W x 14.7” D
88.1 mm H x 212.3 mm W x
392.4 mm D
3.5” H x 8.4” W x 15.4” D
Warranty
Product Regulation
3.8 kg (8.4
lbs) net, 5.1
kg (11.3 lbs)
shipping
Same as
E3610A
One year for E3600 Series power supplies
Three months for standard shipped accessories
Certified to CSA 22.2 No. 231; conforms to IEC 1010-1; carries CE mark; complies with CISPR-11, Group 1, Class A
Ordering Information
Other Options
Rackmount Kits*
E3600 Series Power Supplies
E3610A 30-Watt Power Supply
E3611A 30-Watt Power Supply
E3612A 30-Watt Power Supply
E3614A 48-Watt Power Supply
E3615A 60-Watt Power Supply
E3616A 60-Watt Power Supply
E3617A 60-Watt Power Supply
E3620A Dual-output Power Supply
E3630A Triple-output Power Supply
Opt. 1CM Rackmount kit* (Only
applicable for E3614A, E3615A,
E3616A, E3617A and E3620A)
Opt. 0L2 Extra manual
Opt. UK6 Commercial calibration with
test result data
E3600A-100 Test lead kit
E3614A/15A/16A/17A/20A
To rackmount two instruments sideby-side
‡ /RFNOLQN.LW31
‡ )ODQJH.LW31
Standard Shipped Accessories
User’s guide, Product Reference CD,
power cord
Power Options
Extra Manual Sets
E3610A/11A/12A Manual
(P/N 5959-5304)
E3614A/15A/16A/17A Manual
(P/N 5959-5310)
E3620A Manual
(P/N E3620-90001)
E3630A Manual
(P/N 5959-5329)
Opt. 0E3 230 Vac ± 10%
Opt. 0EM 115 Vac ± 10%
Opt. 0E9 100 Vac ± 10%
4
To rackmount one or two instruments
in a sliding support shelf
‡ 6XSSRUW6KHOI31
‡ 6OLGH.LW31
required for support shelf
For a single instrument, also order
filler panel (P/N 5002-3999)
* Rackmounting with 1CM or locklink/flange kit requires
‡ $JLOHQWRUFXVWRPHUVXSSRUWUDLOV
‡ $JLOHQW6XSSRUW5DLOV($&.
www.agilent.com
Agilent Email Updates
www.agilent.com/find/emailupdates
Get the latest information on the
products and applications you select.
Agilent Direct
www.agilent.com/find/agilentdirect
Quickly choose and use your test
equipment solutions with confidence.
Agilent
Open
www.agilent.com/find/open
Agilent Open simplifies the process
of connecting and programming
test systems to help engineers
design, validate and manufacture
electronic products. Agilent offers
open connectivity for a broad range
of system-ready instruments, open
industry software, PC-standard I/O
and global support, which are
combined to more easily integrate
test system development.
Remove all doubt
Our repair and calibration services
will get your equipment back to you,
performing like new, when promised. You will get full value out of
your Agilent equipment throughout its lifetime. Your equipment
will be serviced by Agilent-trained
technicians using the latest factory
calibration procedures, automated
repair diagnostics and genuine parts.
You will always have the utmost
confidence in your measurements.
Agilent offers a wide range of additional expert test and measurement services for your equipment,
including initial start-up assistance
onsite education and training, as
well as design, system integration,
and project management.
For more information on repair and
calibration services, go to
www.agilent.com/find/removealldoubt
Product specifications and descriptions
in this document subject to change
without notice.
For more information on Agilent Technologies’
products, applications or services, please
contact your local Agilent office. The complete list is available at:
www.agilent.com/find/contactus
Phone or Fax
Americas
Canada
Latin America
United States
(877) 894-4414
305 269 7500
(800) 829-4444
Asia Pacific
Australia
China
Hong Kong
India
Japan
Korea
Malaysia
Singapore
Taiwan
Thailand
1 800 629 485
800 810 0189
800 938 693
1 800 112 929
0120 (421) 345
080 769 0800
1 800 888 848
1 800 375 8100
0800 047 866
1 800 226 008
Europe & Middle East
Austria
Belgium
Denmark
Finland
France
01 36027 71571
32 (0) 2 404 93 40
45 70 13 15 15
358 (0) 10 855 2100
0825 010 700*
*0.125 /minute
07031 464 6333
Germany
1890 924 204
Ireland
972-3-9288-504/544
Israel
39 02 92 60 8484
Italy
31 (0) 20 547 2111
Netherlands
34 (91) 631 3300
Spain
0200-88 22 55
Sweden
0800 80 53 53
Switzerland
44 (0) 118 9276201
United Kingdom
Other European Countries:
www.agilent.com/find/contactus
Revised: October 6, 2008
© Agilent Technologies, Inc. 2009
Printed in USA, October 20, 2009
5968-9727EN
Download PDF

advertising