Service Manual
Auto Washer
Model :
DWF-5510/5511/5520/5521
6010/6011/6020/6021
DAEWOO ELECTRONICS CO., LTD.
OVERSEAS SERVICE DEPT.
AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASH-
ER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO
WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER
AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASH-
ER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO
WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER
AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASH-
ER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO
WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER
Contents
2
3
4
1. SPECIFICATIONS
2. STRUCTURE OF THE WASHING MACHINE
3. FUNCTIONS OF THE CONTROL PANEL
4. WASHING PROCEDURE AND COURSE SELECTION
FULL AUTOMATIC COURSE
RESERVED WASHING
PARTIAL SELECTION AMONG WASH, RINSE OR SPIN
5. DIRECTIONS FOR INSTALLATION AND USE
INSTALLATION OF THE UNDER BASE COVER
HOW TO INSTALL ON AN INCLINED PLACE
HOW TO CONNECT THE INLET HOSE
HOW TO CLEAN THE FILTER
6. FEATURE AND TECHNICAL EXPLANATION
FEATURE OF THE WASHING MACHINE
WATER CURRENT TO ADJUST THE UNBALANCED LOAD
AUTOMATIC WATER SUPPLY SYSTEM FOR BLANKET WASH
PULSATOR SYSTEM
AUTOMATIC DRAINING TIME ADJUSTMENT
SOFTENER DISPENSER
AUTOMATIC UNBALANCE ADJUSTMENT
CIRCULATING-WATER COURSE AND LINT FILTER
LINT FILTER
RESIDUAL TIME DISPLAY
DRAIN MOTOR
GEAR MECHANISM ASS’Y
PRINCIPLE OF BUBBLE GENERATOR
FUNCTIONAL PRINCIPLE OF BUBBLE WASHING MACHINE
7. DIRECTIONS FOR DISASSEMBLY AND ADJUSTMENT
GEAR MECHANISM ASS’Y REPLACEMENT
DRAIN MOTOR AND VALVE
BRAKE ADJUSTMENT
8. TROUBLE SHOOTING GUIDE
CONCERNING WATER SUPPLY
CONCERNING WASHING
CONCERNING DRAINING
CONCERNING SPINNING
CONCERNING OPERATION
9. PRESENTATION OF THE P.C.B ASS’Y
APPENDIX
WIRING DIAGRAM
PARTS DIAGRAM & PARTS LIST
CIRCUIT DIAGRAM
20
21
22
23
24
25
16
16
17
14
15
15
15
12
12
13
14
11
11
11
26
30
39
18
19
19
9
10
8
8
5
7
7
1. SPECIFICATIONS
NO.
ITEM DWF-5510 DWF-5511 DWF-5520 DWF-5521 DWF-6010 DWF-6011 DWF-6020 DWF-6021
1 POWER SOURCE AVAILABLE IN ALL LOCAL AC VOLTAGE
2
POWER 50Hz
CONSUMPTION 60Hz
250W
270W
3
MACHINE NET
WEIGHT GROSS
32
35
32.5
36
32.5
36
33
37
32.5
36
33
37
33
37
33.5
38
4 DIMENSION (WXHXD)
532X855X542 532X920X542 532X887X542 532X952X542 532X855X542 532X920X542 532X887X542 532X952X542
5 MATERIAL OF INTERNAL TUB PLASTIC STAINLESS STEEL
6 WASHING COURSE
7 WATER LEVEL SELECTOR
8 OPERATING WATER PRESSURE
9 MAXIMUM MASS OF TEXTILE
10
REVOLUTION
PER MINUTE
WASH
SPIN
SUIT
5.5Kg
FULL AUTOMATIC 4 COURCE
(FUZZY, LIGHT, HEAVY, WOOL/SUIT)
HIGH(55 l ), MID(45 l ), LOW(31
0.3kgf/cm 2 ~8kgf/cm 2 (2.94 N/cm 2 l )
~78.4N/cm 2 )
125~145(50Hz), 130~150(60Hz)
710~725(50Hz), 760~785(60Hz)
50(50Hz), 60(60Hz)
6.0Kg
11 DIRECTION INLET VALVE
12 WATER CONSUMPTION
BACKWARD UPWARD BACKWARD UPWARD
APPROX. 135 l /CYCLE APPROX. 130 l /CYCLE
13 PULSATOR PROVIDED WITH 6 SPOUTING HOLES FOR POWERFUL UPWARD WATER STREAM
14 WATER LEVEL CONTROL
15 ANTI NOISE PLATE
ELECTRONICAL SENSOR
OPTION
16 GEAR MECHANISM ASS’Y
17 LINT FILTER
18 SOFTENER INLET
19 ALARM SIGNAL
20 AUTO. WATER SUPPLY
21 FUNCTION FOR BUBBLE
22 AUTO RE-FEED WATER
23 AUTO POWER OFF
SPUR GEAR
O
O
O
O
OPTION
O
O
2 SPECIFICATIONS
3. FUNCTIONS OF THE CONTROL PANEL
Control panel has micom sensor.
As the buttons are pressed, the lamps indicating the selection of your desired washing program will light up.
§
è
Dwf-5510/5511/6010/6011
POWER
HIGH
MID
LOW
WATER
LEVEL
D A E W O O A U T O M A T I C W A S H E R
RES.
FUZZY
LIGHT
HEAVY
SUIT
RES.
COURSE
ADD
WASH
RINSE
SPIN
HOT
COLD
TEMP
PROCESS
START
/ HOLD
§
è
Dwf-5520/5521/6020/6021
POWER
HIGH
MID
LOW
WATER
LEVEL
D A E W O O A U T O M A T I C W A S H E R
RES.
FUZZY
LIGHT
HEAVY
SUIT
RES.
COURSE
ADD
WASH
RINSE
SPIN
HOT
COLD
TEMP
PROCESS
START
/ HOLD
POWER
WATER
LEVEL
RES.
COURSE
PROCESS
TEMP
START
/ HOLD
Power Switch
• Press this button to turn the power ON or OFF.
Water Level Selector
• This button is used to select the water level you want.
Reservation Button
• If you want to reserve the finishing time of washing, use this button.
As this button is pressed, digit in display increases by 1 hour at one press.
• If current time is 8:00 am and you expect washing will be completed around 5:00 pm, press this nine times in order to display ‘9’.
Course Selector
• This button is used to select the washing course according to the type of wash loads.
• Either WOOL or SUIT course is adopted to your washing machine.
Program Button
• With this button, you can create new programs by combinations of process.
Temperature Selector (Optional)
• If your washer is connected to two water taps for cold water and hot water, you can select them. Without operation, cold water would be selected automatically.
Start/Hold
• With this button, you can make your washer proceed your program, or stop temporarilly.
And you can also release the temporary stop by pressing this.
4 CONTROL PANEL
§
è
Reserved Washing
1 Set your program as the above procedure, remaining last step.
• Press the course selection button.
• Press the procedure selection button.
• But WOOL/SUIT course can not reservation.
2 Press reservation button until the digital monitor displays the finishing time you want.
3 Press Start/Hold to start.
RES.
START
/ HOLD
§
è
Partial Selection Among Wash, Rinse or Spin
step 1. Press power switch.
step 2. Press program button until the indicating lamps make the combinations you want.
If only spin lamp is turned on, that means you will operate your washer for spin only.
If rinse and spin lamp are turned on, that means you will operate your washer for rinse and spin.
If add lamp is turned on with other porcess lamps, that means the time of the corresponding porcess will increase by 1~2 minutes, that is, if add is on with wash, rinse and spin, the time of each precess will increase by 1~2 minutes. (Wash: add 2 min., Rinse: add 1 min., Spin: add 1 min.) step 3. Press water level selector as your decision.
step 4. Press Start/Hold to start.
1 Processing the Power
Switch
2 Selecting
Water level 3 Selecting Course
4 Pressing the Start/Hold
Switch
POWER
§ HIGH
§ MID
§ LOW
WATER
LEVEL
§ ADD
§ WASH
§ RINSE
§ SPIN
PROCESS
Wash & Rinse
& Spin
Only Spin
Add & Wash
Add & RInse
& Spin
Add & Spin
Add & Wash
& Rinse & Spin
Only Wash
Rinse & Spin
§ ADD
§ WASH
§ RINSE
§ SPIN
§ ADD
§ WASH
§ RINSE
§ SPIN
§ ADD
§ WASH
§ RINSE
§ SPIN
§ ADD
§ WASH
§ RINSE
§ SPIN
§ ADD
§ WASH
§ RINSE
§ SPIN
§ ADD
§ WASH
§ RINSE
§ SPIN
§ ADD
§ WASH
§ RINSE
§ SPIN
§ ADD
§ WASH
§ RINSE
§ SPIN
START
/ HOLD
End of
Washing
It is Informed by buzzer.
PROCEDURE 7
5. DIRECTIONS FOR INSTALLATION AND USE
Installing Place
Install the washer on a horizontal solid floor. If the washer is installed on an unsuitable floor, it could make considerable noise and vibration.
10Cm
Keep the machine body more than 25cm apart from the wall surface. It will make easy cleaning the drain filter which is equipped at the back side of it.
And if it comes into contract vibration may occur.
Never install in these places
¡ The place where it would be exposed to direct sunlight.
¡ The place nearby a heater or heat appliance.
¡ The place where it would be supposed to be frozen in winter.
¡ The kitchen with coal gas and a damp place like a bathroom.
§
è
Installation Of The Under Base Cover [Option]
-DWF-5510/5511/5010/6011
1 Before installing your washer, remove the pad from the bottom of the cabinet. Then, separate under cover from rear side of cabinet by unscrewing and insert it into the base.
SCREW
2 Push the under-base cover into the end, which decrease the noise made by this washer.
-DWF-5520/5521/6020/6021
1 There is under-base cover in the tub of the washer. Put out and draw it in its proper site. (See picture)
2 Push the under-base cover into the end, which decrease the noise made by this washer.
§
è
How To Install On An Inclined Place
1 Horizon
Setting
After controlling the height by turning the adjustable leg, let the washer put down to the ground.
2 Check the Horizon
Status
Check the position of tub above the center of the washer.
NOTES
The openings must not be obstructed by carpeting when the washing machine is installed on a carpeted floor.
8 DIRECTIONS
6. FEATURE AND TECHNICAL EXPLANATION
Feature of the Washing Machine
1 The first air bubble washing system in the world.
2 Quiet washing through the innovational low-noise design.
3 The wash effectiveness is much more enhanced because of the air bubble washing system.
4 The laundry detergent dissolves well in water because of the air bubble washing system.
5 The adoption of the water currents to adjust the unbalanced load.
6 One-touch operation system.
Water Current to Adjust the Unbalanced Load
It is a function to prevent eccentricity of the clothes after wash by rotating pulsator C.W and C.C.W for 35 seconds.(But, the SUIT course have no operation of the water currents to adjust the unbalnced load.)
EFFECT
It reduces vibration and noise effectively while spinning.
WATER FLOW
WASH DRAIN SPIN FILL RINSE 1 DRAIN SPIN FILL RINSE 2 DRAIN •••
MOTOR C.W
SINGAL C.C.W
TIME(SEC.) 0.4
0.4
0.4
0.4 0.4
0.4
40 SEC. (About 25 Times)
* When the water level is “HIGH”
• • • • • • •
Automatic Water Supply System For Blanket Wash
The water level would be lowered because the blanket absorbs water at the beginning of washing. Therefore, after
60 seconds, the operation is interrupted to check the water level, and then the water is supplied again until the selected water level is reached.
EXPLANATION 11
Pulsator System
When the pulsator is rotated C.W or C.C.W at a high speed, it makes the cyclone water flow from the asymmetrically designed pulsator as shown below.
Asymmetrically designed pulsator makes the cyclone water flow, which get rid of the washing dead zone to increase the washing effect and reduce the entanglement of laundry.
Automatic Drainning time Adjustment
This system adjusts the draining time automatically according to the draining condition.
Draining condition
Good draining
Bad draining
No draining
The washer begins spin process after drainage.
Draininig time is prolonged.
Program is stopped and gives the alarm.
FUNCTIONAL PRINCIPLE
1 The micom can remember the time from the begining of drain to reset point when the pressure switch reaches to
“OFF” point
Movement of the Program Drain Time
Less than
10 minutes
More than
10 minutes
Continue draining
Program stops and gives the alarm with blinked on display lamp.
2 In case of continuous draining, residual drain time is determined by micom.
Draining time as a whole = D + 30
Residual drain time.
The time remembered by micom.
12 EXPLANATION
Softener Dispenser
This is the device to dispense the softener automatically by centrifugal force.
This is installed inside the auto-balancer.
FUNCTIONAL PRINCIPLE
1 Softener stays in room (A) when poured into softener inlet.
2 Softener moves from (A) to (B) by centrifugal force during intermittent spin process.
3 Softener flows from (B) to (C) during rinse process next to intermittent spin.
4 Softener moves from (C) to (D) by centrigfugal force during second intermittent spin.
After spin process is finished, the softener is added into the tub through softener outlet.
FLOW OF THE SOFTENER
Normal
Course
Wash Intermittent
Spin
(A)
Centrifugal force
(B)
Hold
Flow in
(C)
Intermittent
Spin
Centrifugal force
(D)
Rinse
Flow in
FLOW OF THE SOFTENER INSIDE OF THE BALANCER
Room inside the balancer
A B C
Centrifugal force
Flowing by weight
D
Spin
NOTES Softener moves into the next room when r.p.m of the tub is more than 100 r.p.m.
HOW TO CHECK MOVEMENT
Pour a reasonable amount of “MILK” into softener dispenser and operate the washer with no load. In final rinse cycle, make sure that the milk is added into the tub through softener outlet.
Balancer
B
A
Softener inlet
C
D
Softener outlet
EXPLANATION 13
Automatic Unbalance Adjustment
This system is to prevent abnormal vibration during intermittent spin and spin process.
FUNCTIONAL PRINCIPLE
1 When the lid is closed, the safety switch contact is “ON” position.
2 In case that wash loads get uneven during spin, the outer tub hits the safety switch due to the serious vibration, and the spin process is interrupted.
3 In case that P.C.B. ASS’Y gets “OFF” signal from the safety switch, spin process are stopped and rinse process is started automatically by P.C.B. ASS’Y.
4 If the safety switch is operated due to the unbalance of the tub, the program is stopped and the alarm is given.
Position of unbalanced load (OFF)
Contact of safety switch Lid closing
Contact lever A
Normal (ON)
Lid opening
NOTES
The alarm finished when you close the lid after opening it. Check the unbalance of the wash load and the installation condition.
Circulating-Water Course and Lint Filter
CIRCULATING-WATER
The washing and rinsing effects have been improved by adopting the water system in which water in the tub is circulated in a designed pattern.
When the pulsator rotates during the washing or rinsing process, the water below the pulsator vanes creates a water currents as shown in figure.
The water is then discharged from the upper part of the tub through the water channel.
About 40 L/min. water is circulated at the ‘high’ water level, standard wash load and standard water currents.
Filter
Water channel
Pulsator
Tub
Outer tub
14 EXPLANATION
Lint Filter
Much lint may be obtained according to the kind of clothes to be washed and some of the lint may also sticks to the clothes.
To minimize this possibility a lint filter is provided on the upper part of the tub to filter the wash water as it is discharged from the water channel. It is good to use the lint filter during washing.
Bleach Inlet
Inlet
HOW TO REPLACE LINT FILTER
1 Pull the filter frame upward.
2 Turn the lint filter inside out, and wash the lint off with water.
3 Return the filter as it was, and fix the filter frame to the slot.
Residual Time Display
When the START/HOLD button is pressed, the residual time (min.) is displayed on the time indicator, and it will be counted down according to process.
When operation is finished, the TIME INDICATOR will light up .
Drain Motor
STRUCTURE
Pull
Loosen
Pulley
Lever
Inductive ring
Magnet
Coil of motor
Magnet of motor
FUNCTIONAL PRINCIPLE
1 When the DRAIN MOTOR connected to the power source, the DRAIN MOTOR rotates with 900 r.p.m and revolves the pulley by gear assembly for reducing.
2 When the pulley is rotated, the pulley winds the wire to open the drain valve.
3 Therefore, rotation of pulley changed to the linear moving of wire.
4 The wire pulls the brake lever of Gear Mechanism Ass’y within 5 seconds.
5 After the wire pulled, gear assembly is separated from motor and condition of pulling is held by operation of the lever.
6 When the power is turned off, the drain valve is closed because the wire returns to original position.
EXPLANATION 15
Gear Mechanism Ass’y
The proper water currents is made by the rotation of pulsator at a low speed to prevent the damage to the small sized clothes.
Pulsator shaft
Spin shaft
One way clutch bearing Gear unit as
Planetary gear
Sun gear
Internal gear
Brake lever
Clutch spring
Clutch boss
Gear pulley
Gear unit as
Motor
Pulsator
1 revolution
5 revolutions
Gear pulley
Motor
1490 r.p.m
(50Hz)
Gear Pulley
720 r.p.m
Gear Unit as
Directly
Pulsator
138 r.p.m
Tub
720 r.p.m
V-belt
Principle of Bubble Generator
STRUCTURE
Bobbin & coil
Magnet
Trans core
Armature
Bellows
Air in hole
Protector B
Protector A
Air out hole
16 EXPLANATION
PRINCIPLE OF INTAKE & OUTLET OF THE AIR
INTAKE : ARMATURE moves up, and BELLOWS inhales the air. At the same time, protector B is open and A is close.
OUTLET : ARMATURE moves down, and BELLOWS exhausts the air. At the same time, protector B is close and A is opend.
FUNCTIONAL PRINCIPLE OF TRANS & MAGNET
¡ The phase of A.C electric power changes to 60 cycle/second.
¡ The magnetic pole of trans core is changed by the change of the phase of A.C electric power.
¡ The core repeats push and pull (3600 times/min.) of the at mature magnet.
A.C
A.C
N
S
NS
LEAF SPRING
TRANS CORE
MAGNET
S
N
NS
Functional Principle of Bubble Washing Machine
ACROSS SECTION
Air bubble
Tub
Outer tub
Pulsator
Nozzle
FUNCTIONAL PRINCIPLE
Bubble generator supplies the air from the bottom of outer tub to the inner space of pulsator, the air is dispersed by the rotation of pulsator. Air-bubble is created by the centrifugal force, and rises up.
EXPLANATION 17
7. DIRECTIONS FOR DISASSEMBLY AND ADJUSTMENT
Warning
BEFORE ATTEMPTING TO SERVICE OR ADJUST ANY PART OF THE WASHING MACHINE, DISCON-
NECT THE POWER CORD FROM THE ELECTRIC OUTLET.
Gear Mechanism Ass’y Replacement
¡
¡
Raise the top plate on the outer cabinet.
Remove outer tub cover from the tub ass’y.
Outer tub cover
¡ Loosen the pulsator mounting screw and remove the pulsator.
Pulsator Mounting screw
¡ Remove the spinner shaft flange nut by using ‘T’ type box wrench.
"T" type box wrench Washer
Nut-spin shaft fixing
¡ Remove the tub ass’y.
pulsator
Nut-spin shaft fixing
Washer-spin
Shaft fixing
Tub ass'y
¡
¡
¡
Lay the front of the washer on the floor.
Remove four bolts mounting the plate-gear protect by using a box wrench and remove plate-gear protect.
Remove the V-belt.
¡
¡
Remove four bolts mounting the gear mechanism ass’y by using a box wrench.
Pull out the gear mechanism ass’y.
Gear mechanism ass'y
Mounting bolt
Mounting bolt
NOTES
To assemble the gear mechanism ass’y, reverse the disassembly procedure.
18 DIRECTIONS
Drain Motor and Valve
¡ Lay the front of the washer on the floor.
¡ Loosen the adjustment screw and two bolts mounting the drain motor.
¡ Take out the wire of drain motor from the bracket.
Drain motor
Wire Bracket
Adjustment screw
¡ Separate the drain motor from the bracket.
¡ Turn the valve lid by using screw driver as shown in figure and remove the valve lid from the valve frame.
Valve frame
Bracket
Adjustment screw
Screw dirver Valve lid Pin Bellows
Valve lid
Brake Adjustment
¡ Loosen the adjustment screw fastening the bracket and place the adjustment screw to the brake lever as shown in figure.
¡ Tighten the adjustment screw completely.
3.0mm
Adjustment screw
¡ Tighten the link brake screw completely.
Link brake
Brake lever
Clutch lever
Adjustment bolt
(Non pump model)
Brake lever
Adjustment bolt
(Pump model)
Clutch lever
¡ Loosen the adjustment bolt and turn the adjustment bolt until the end of the bolt touches to the brake lever.
¡ Tighten the lock nut and apply a small amount of paint-lock.
Adjustment bolt
Clutch lever
Brake lever
NOTES:
1. The brake adjustment has been made at the factory, so that it is not re-adjust.
However, in case of insufficient brake operation, problem the upper procedure.
2. Overtightening of the adjustment bolt will cause poor brake performance.
3. Undertightening of the adjustment bolt will cause continuous braking and thereby.
cause the problems of the motor during the spingcycle.
Gear mechanism ass'y
DIRECTIONS 19
8. TROUBLE SHOOTING GUIDE
NOTES
1. When replace the P.C.B. ASS’Y do not scratch the surface of the P.C.B. ASS’Y.
2. Disconnect the power cord from the electric outlet.
Concerning Water Supply
PROBLEM CHECK POINT CAUSE
WATER IS
NOT SUP-
PLIED.
SOLUTION
Do you open the water tap?
YES
Is the filter of the water inlet valve clogged with dirt?
NO
Is the water pressure sufficient?
(0.3~8 kgf/cm 2 )
NO
YES
Open the water tap.
Clean the filter.
YES
NO Increase the water pressure.
NOTE : Open the water tap fully and measure the flow rate.
Flow rate( l /min.)
Water pressure
(Kgf/cm 2 )
11.5
0.3
15.0
0.4
18.0
0.5
20.3
0.6
24.1
0.8
27.4
1.0
From the upper results, you know that the flow rate more than
11.5
l /min. is essential for water supply.
Does the water inlet valve make operating sound?
NO
Water inlet valve is defective.
YES
Is the connector or the terminal connected properly?
YES
Is the output voltage of the P.C.B normal?
NO
Improper connection of the connector or the terminal.
NO
P.C.B AS is defective.
Change water inlet valve.
Connect the connector or the terminal properly.
Change the P.C.B AS.
YES
Lead wire is defective.
Change the lead wires.
20 TROUBLE SHOOTING
PROBLEM
WATER SUP-
PLY IS NOT
STOPPED.
CHECK POINT CAUSE
Does the water supply continue while the power is turned off?
NO
Does the water supply start as soon as you press the power switch?
NO
Operate the washer after setting the water level to
“HIGH”
YES
YES
The water inlet valve is defective.
The triac of P.C.B is defective.
NO
Does the water supply continue after the water reaches to the “HIGH” level?
YES
Is the air tube of water level switch kinked or deformed?
YES
NO
Air tube is defective.
Pressure switch is defective.
Concerning Washing
PROBLEM CHECK POINT CAUSE
THE PUL-
SATOR DOES
NOT ROTATE
EVEN IF THE
WATER IS
SUPPLED.
Does the motor operate after finishing water supply?
NO YES
Does pulsator rotate in only one direction?
YES The triac of P.C.B is defective.
NO
Does the motor make operating sound?
YES NO
Is the motor coil disconnected?
YES
Motor is defective.
Is the connection condition of capacitor terminal good?
YES
Is the V-belt worn out?
NO
NO
YES
Improper connection
V-belt is defective.
SOLUTION
Change the water inlet valve.
Change the P.C.B ASS’Y.
Normal operation.
Change the air tube.
Change the pressure switch.
SOLUTION
Change the P.C.B
ASS’Y.
Normal
Change the motor.
Connect the terminal properly.
Change the V-belt.
Change the motor.
TROUBLE SHOOTING 21
Concerning Draining
PROBLEM CHECK POINT CAUSE
Do you install the drain hose properly?
NO
Improper installation
THE WASHER
DOES NOT
DRAIN.
YES
Is the foreign matter accumulated inside the pump housing?
YES
Malfunction of drainage by the foreign matter
NO
Is the output voltage of the drain pump normal?
YES
Drain pump is defective
NO
P.C.B ASS’Y is defective.
SOLUTION
Install the drain hose properly.
Remove the foreign matter from the pump housing
Change the Drain pump
Change the P.C.B ASS’Y.
22 TROUBLE SHOOTING
Concerning Spinning
PROBLEM CHECK POINT CAUSE
YES
Is the lid open?
NO
THE WASHER
DOES NOT
SPIN.
Does the safety switch operate normally?
YES
Is the connector of
P.C.B ASS‘Y connected properly?
YES
NO Safety switch is defective.
NO
Improper connection of the connector.
P.C.B. ASS’Y is defective.
Does the pulsator rotate while the tub does not rotate?
NO YES
YES
Drain motor is defective.
Is the input voltage of the drain motor normal?
NO
P.C.B ASS’Y is defective.
Is the V-belt worn out?
YES
V-belt is defective.
NO
Is the input voltage of motor normal?
NO
Is the connection condition of capacitor terminal good?
YES
YES
Motor is defective.
NO
Improper connection.
P.C.B ASS’Y is defective.
SOLUTION
Close the lid.
Change the safety switch.
Connect the connector properly.
Change P.C.B ASS’Y.
Change the drain motor.
Change the P.C.B ASS’Y.
Change the V-belt.
Change the motor.
Connect the terminal correctly.
Change the P.C.B ASS’Y.
TROUBLE SHOOTING 23
Concerning Operation
PROBLEM CHECK POINT CAUSE
THE INDICA-
TOR
LAMPS(L.E.D)
DO NOT LIGHT
UP WHEN THE
POWER BUT-
TON IS
PRESSED.
Is the plug connect-ed to electric outlet?
YES
Is Fuse opended?
NO
Is the condition of power button good?
YES
Is the connector of the
P.C.B. ASS’Y connected properly?
YES
NO
NO
YES
Power button is defective
NO
Improper connection of the connector.
P.C.B. ASS’Y is defective.
SOLUTION
Connect the plug.
Change Fuse
Change P.C.B ASS’Y.
Connect the connector properly.
Change P.C.B ASS’Y.
PROGRESS
LAMPS(LED)
DO NOT LIGHT
UP.
Do you press
START/HOLD button?
YES
NO
P.C.B ASS’Y is defective.
MOTOR
ROTATES
WHEN
START/HOLD
BUTTON IS
NOT
PRESSED.
Does the pressure switch operate normally?
YES
Check the output voltage of P.C.B ASS’Y
NO Pressure switch is defective.
Abnormal
P.C.B ASS’Y is defective
ABNORMAL
NOISE DUR-
ING WASH
PROCESS.
Is the strange noise generated when the pulsator rotates in TEST MODE of P.C.B ASS’Y?
NO
Is the V-belt worn out?
YES There is foreign matter between pulsator and tub.
YES
V-belt is defective.
Press START/HOLD button.
Replace P.C.B ASS’Y.
Change the pressure switch.
Change P.C.B ASS’Y.
Remove the foreign matter.
Change the V-belt.
24 TROUBLE SHOOTING
9. PRESENTATION OF THE P.C.B ASS’Y
Concerning Error Message
MESSAGE CAUSE SOLUTION
Improper installation of drain hose.
Install drain hose properly.
Remove foreign matter from drain hose.
The drain hose is blocked up by foreign matter.
Drain motor is inferior.
Change drain motor.
The water tap is closed.
Open the water tap.
The water inlet filter clogged.
Clean the water inlet filter.
It passes over the 30 minutes, yet it doesn’t come to assigned water level.
Check whether or not is comes to the assigned water level.
Wash loads get uneven during spin.
Re-set wash loads evenly.
Poor installation of the unit.
Proper installation.
The lid is opened.
Close the lid.
The safety switch is inferior.
Change the safety switch.
The load sensing is inferior. After the load sensing operates about 7 seconds, the message is displayed during 1 second and water level is always fixed ‘high’.
Change the P.C.B. ASS’Y.
The water level sensing is inferior.
Check the water level sensor and the contact part of the connector.
PCB ASS’Y 25
APPENDIX
§
è
Wiring Diagram [non-pump]
26 WIRING DIAGRAM
§
è
[Non-Pump, Single Valve]
WIRING DIAGRAM 27
§
è
[Pump]
28 WIRING DIAGRAM
§
è
[pump, single valve]
WIRING DIAGRAM 29
§
è
Parts List
LOC.
PART NAME
A01
A02
A03
A04
A05
A06 NOZZLE DETERGENT
A07
A08
A09
A10
A11
A12
A13
A14
A15
A16
A17
PANEL B
VALVE INLET(HOT)
VALVE INLET(COLD)
SWITCH SAFETY AS
PLATE T
CASE DETERGENT
CAP REAR
HANDLE DOOR
DOOR SPRING
DOOR B
DOOR F
WINDOW DISPLAY
BRACKET
UNIT CAPACITOR AS
SENSER PRESSURE
PANEL F
3615403510
3615403530
3615403310
3615403330
3619006360
3619043600
3614515000
3614515100
3618102000
3618102100
3611116500
3611117200
3610902600
3612603600
3612604000
3615107700
PART CODE
3614219200
3614220200
3615403830
3615403810
3615402130
3615402110
3615403630
3615403610
3615403710
3615403730
3615402010
3615402030
3615108900
3611718400
3611793300
3611718300
3611793200
3615501700
3615501800
3610602900
3618911700
3618911600
3618912000
3618911900
3614800960
3614219100
3614200100
ABS
ABS
PP
PP
ABS
ABS
CR
ABS
ABS
SUS304
SUS304
ABS
ABS
ABS
ABS
ABS
ABS
PP
9.4µF, CAN TYPE
8.4µF, CAN TYPE
33.6µF, CAN TYPE
30µF, CAN TYPE
DC 5V CDN-D7
ABS
ABS
SPECIFICATION
ABS
ABS
AC 220~240V/50Hz
(NP, N, MP, M)
AC 220V~60Hz
(LP, L)
AC 110~127V/60Hz
(TP, T, SP, S)
AC 220~240V/50Hz
(NP, N, MP, M)
AC 220V60Hz
(LP, L)
AC 110~127V/60Hz
(TP, T, SP, S)
AC 110V/50, 60Hz
(J)
DC 15V 10A
REMARK
5510,5511,6010,6011
5520,5521,6020,6021
5510,5511,6010,6011
5520,5521,6020,6021
5510,5511,6010,6011
5520,5521,6020,6021
5510,5511,6010,6011
5520,5521,6020,6021
5510,5511,6010,6011
5520,5521,6020,6021
5510,5511,6010,6011
5520,5521,6020,6021
5510,5511,6010,6011
5520,5521,6020,6021
5510,5511,6010,6011
5520,5521,6020,6021
5510,5511,6010,6011
5520,5521,6020,6021
5510,5511,6010,6011
5520,5521,6020,6021
5510,5511,6010,6011
5520,5521,6020,6021
5510,5511,6010,6011
5520,5521,6020,6021
5510,5511,6010,6011
5520,5521,6020,6021
5510,5511,6010,6011
5520,5521,6020,6021
5510,5511,6010,6011
5520,5521,6020,6021
5510,5511,6010,6011
5520,5521,6020,6021
5510,5511,6010,6011
5520,5521,6020,6021
AC 220~230V/50HZ
AC 240V/50Hz, AC 220V/60Hz
AC 110V/60Hz
AC 127V/60Hz
5510,5511,6010,6011
5520,5521,6020,6021
PARTS DIAGRAM 31
LOC.
A18
A19
PART NAME
A20 CORD POWER AS
A21
PCB AS
ASSY BUBBLE
HARNESS ASSY
3618946300
3918946400
3611304600
3611304700
3611304800
3611304900
3611305000
3611305100
3611305200
3611305300
3611305400
3611305500
3611305600
3611305700
3611305800
3611305900
3612754500
3612754510
3612754520
3612754530
3612754600
3612754610
3612754620
3612754630
PART CODE SPECIFICATION
PRPSSW8100 AC 220~230V/50Hz PUMP
PRPSSW8200 AC 220~230V/50Hz N-PUMP
PRPSSW8101 AC 240V/50Hz PUMP
PRPSSW8201 AC 240V/50Hz N-PUMP
PRPSSW8102 AC 220V/60Hz PUMP
PRPSSW8202 AC 220V/60Hz N-PUMP
PRPSSW8103 AC 110V/60Hz PUMP
PRPSSW8203 AC 110V/60Hz N-PUMP
PRPSSW8104 AC 127V/60Hz PUMP
PRPSSW8204 AC 127V/60Hz N-PUMP
PRPSSW8205 AC 100V/50,60Hz
PRPSSW8300 AC 220~230V/50Hz PUMP
PRPSSW8400 AC 220~230V/50Hz N-PUMP
PRPSSW8301 AC 240V/50Hz PUMP
PRPSSW8401 AC 240V/50Hz N-PUMP
PRPSSW8302 AC 220V/60Hz PUMP
PRPSSW8402 AC 220V/60Hz N-PUMP
PRPSSW8303 AC 110V/60Hz PUMP
PRPSSW8403 AC 110V/60Hz N-PUMP
PRPSSW8304 AC 127V/60Hz PUMP
PRPSSW8404 AC 127V/60Hz N-PUMP
PRPSSW8405 AC 100V/50,60Hz
AC 220~240V/50,60Hz
AC 110~127V/50,60Hz
LFC-3R 3X0.75 2.3M GY
F H05W 3X0.75 2.3M WH
RW-300/500 3X0.75 2.3M
- VCTF 3X0.75 2.3M
R VCTFK 2X1.25 2.3M GY
U VCTF 3X0.75 2.3M GY
P VCTF 3X0.75 2.3M GY
- VCTF 3X0.75 2.3M WH
- H05W-F 3X0.75 2.3M BK
A - VCTFK 2X0.75 2.3M GY
F H05W 3X0.75 2.3M BK
C SJT 3X18AWG 2.2M GY
H05W-F 3X0.75 2.3M GY
P VCTF 3.0.75 2.3M WH
NON OPTION
NON-BUBBLE PUMP
NON-HOT INLET VALVE
FULL OPTION
NON OPTION
NON-BUBBLE PUMP
NON-HOT INLET VALVE
FULL OPTION
32 PARTS DIAGRAM
N-PUMP
REMARK
5510,5511,6010,6011
5510,5511,6010,6011
5510,5511,6010,6011
5510,5511,6010,6011
5510,5511,6010,6011
5510,5511,6010,6011
5520,5521,6020,6021
5520,5521,6020,6021
5520,5521,6020,6021
5520,5521,6020,6021
5520,5521,6020,6021
5520,5521,6020,6021
AUSTRALIA, ARGENTINA
CHILE
PR. CHINA
INDIA
JAPAN
KOREA
KUWAIT
MALAYSIA
SINGAPORE
TAIWAN
USSR, HUNGARY
PANAMA, USA
SOUTH AFRICA
OMAN
PUMP
§
è
Parts List
LOC.
PART NAME
B01 COVER UNDER
B02 PLATE UPPER
B03 COVER B
B04 HOLDER SUPPORT
B05 HOLDER SUPPORT
B06 HOLDER SUPPORT
B07 HANDLE CABINET
B08 CABINET
B09 SARNESS OUTER
B10 BASE U
B11 FOOT
B12 LEG ADJUST AS
HOSE DRAIN O
B13
HOSE DRAIN O AS
B14 GUIDE DRAIN HOSE
B15
CLAMP HOSE O
CLAMP
B16 COVER PUMP
B17
MOTOR SHADED
POLE
B18 FILTER AS
PART CODE
3611402700
3614514900
3611414010
3613010300
3613010200
3613010100
3612603300
3610808100
3610068700
3610311000
3610311900
4509D10020
3617702200
3613217800
3613213500
3612502300
3611202200
3611201000
3611405320
3963514000
3963514010
3963514020
3963514030
3611901530
SPECIFICATION
PP
PP
372x508x0.4t, SGCC
FRPP, B
FRPP, FL
FRPP, FR
PP
1740.2x767.4x0.6t
50/0.18 GREEN ST710480-2
PP
PP
BUTYL RUBBER
DWF-5591DPN
PE-LD
EVA L=950
PP
HSW-3
HSW-3, MFZN D36
PP
AC 220~240V/50Hz
AC 220V/60Hz
AC 110V/60Hz
AC 127V/60Hz
DWF-5590DPNF, E-TYPE
REMARK
EARTH
5510, 5520, 6010, 6020
5511, 5521, 6011, 6021
PUMP
N-PUMP
PUMP
PUMP
N-PUMP
PUMP
PUMP
PUMP
34 PARTS DIAGRAM
§
è
Parts List
LOC.
C01
PART NAME
BALANCER AS
PART CODE
3616104500
3616104700
SPECIFICATION
DWF-5510PN
DWF-6010PN
C02
C03
SPECIAL SCREW
TUB I
4505E05050
3618808100
3618808500
3618808600
5.2x18
PP
SUS
PP C04 TUB U
C05 FILTER AS 4505E82002
3612503900
PE(90*120) INSERT
PP
C06 GUIDE FILTER
3612506700
3619704200
PP
DWF-5510PN
C07 PULSATOR AS
3619704600 DWF-6010PN
C08 SC. PULSATOR FIX AS 4505E3203A 6x26.5, O-RING+SILICON
C09 CAP PULSATOR
C10 SPECIAL NUT
C11 SPECIAL WASHER
C12 FLANGE TUB
C13 SPECIAL SCREW
3610909300
4507D83080
3616006500
4505E05021
4505E05040
PP
SUS 304
SUS 304
ADC-10
5x24
REMARK
5510,5511,5520,5521
6010,6011,6020,6021
5510,5511,5520,5521
6010,6011,6020,6021
6010,6011,6020,6021
5510,5511,5520,5521
6010,6011,6020,6021
5510,5511,5520,5521
6010,6011,6020,6021
36 PARTS DIAGRAM
§
è
Parts List
LOC.
PART NAME
D01 COVER TUB O
D02 TUB O
D03 SUSPENSION AS F
D04 SUSPENSION AS B
D05 NOZZLE BODY
D18 SYNCRONOUS MOTOR
PART CODE
3611414600
3618807600
3619802300
3619802400
3618101400
D06 HOSE DRAIN I
D07 HOSE OVERFLOW
D08 VALVE DRAIN AS
D09
D10
D11
HOSE DRAIN I AS
BASE
SPECIAL BOLT BASE
3613220600
3613220700
3615404020
3613221800
3610302900
4505E83100
3612754900
D12 HARNESS SUB AS
D13 HOSE
D14 CLAMP
3612754910
4500D08220
4500D08180
D15 HOSE
D16 CLAMP
4500D08220
4500D08180
D17 HARNESS EARTH INNER 3612755700
3966010270
3966010260
3966320370
3966320360
D19
D20
D21
D22
D23
LINK BRAKE
GEAR MECHANISM
BOLT HEX
PROTECTOR GEAR
BELT V
PP
PP
SPECIFICATION
DWF-5510NP
DWF-5510NP
PP
TPE
L=245
5591D, VE
DWF-5510N
SECEN 1.6t
6.5x23
SUB HARNESS+EARTH
SUB HARNESS+EARTH
ID=8, L=20
SWC BUBB PIE=8
ID=8, L=30
SWC BUBB PIE=8
L=180
AC 220~240V/50Hz
AC 220~240V/50Hz
AC 220V/60Hz
AC 220V/60Hz
450ED45170 AC 110~127V/60Hz
450ED45176 AC 110~127V/60Hz
3966130260 AC 100V/50,60Hz
3617801010
3617306000
3617306010
PP
GM-4900-KJ4XO
GM-4900-KJ4PO
7640802011
3618301300
4507D34020
4507B34020
6B-1 8x20 SW MFZN
SBHG 1.6t
M 20
M19.5
D24 SPECIAL WASHER 4505E34030
3964340100
D25 MOTOR CONDENSER 3964340200
D26
D27
SPECIAL WASHER
BOLT HEX
3964340300
4505E34040
7650802511
D28
D29
PULLY MOTOR AS
HARNESS SUB AS
3618401420
3618402800
3612754900
3612754910
PP
AC 220~240V/50Hz
AC 220V/60Hz
AC 10~127V/60Hz
PP
6B-1 8X25 HS MFZN
M-TYPE DS=10 DP=53.0
M-TYPE DS=10 DP=48.5
SUB HARNESS + EARTH + PUMP
SUB HARNESS + EARTH
38 PARTS DIAGRAM
REMARK
PUMP
N-PUMP
N-PUMP
N-PUMP
50Hz
60Hz
NP, N, MP, M
LP, L
TP, T, SP, S
50Hz
60Hz
PUMP
N-PUMP
PUMP
N-PUMP
CAVITATION HOSE
BUBBLE HOSE
CHILE
PUMP
N-PUMP
PUMP
N-PUMP
PUMP
N-PUMP
N-PUMP
PUMP
N-PUMP
PUMP
S/M NO. :
DAEWOO ELECTRONICS CO., LTD.
686, AHYEON-DONG MAPO-GU SEOUL, KOREA
C.P.O. BOX 8003 SEOUL, KOREA
TELEX: DWELEC K28177-8
CABLE: “DAEWOOELEC”
FAX: 02) 590-6291
TEL: 02) 360-7114/590-6151~5 http://www.dwe. daewoo.co.kr
PRINTED DATE: NOV.1997
