Dero Decker
ADA Cane Stops
Sturdy red handle
grips
Lift-assist trays
Dampers for safe
lowering of trays
Spring loaded levers
hold bikes firmly in
place
U-lock compatible
Smallest footprint
Smooth and silent
operation
Simple installation
Low maintenance
Specially designed
fat bike trays
available
Adjustable downward
resting position to
accommodate
different floor
clearances
For improved safety, 2″ high, canedetectable extensions for the lower trays
are available (By request only).
American Bicycle Security Company
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865
www.ameribike.com
Email: [email protected]
Dero Decker
Ceiling Height Requirement: 106”
Product
Dero Decker™
Capacity
Modular 2-Tiered System. ONLY available in quantities of 4.
One bike per tray.
Materials
Uprights: 4” 11g square tube
Upright base: 1/4” plate
Cantilevers: 11g plate
Cantilever base: 1/4” plate
Trays: 11g plate
Finishes
Standard option: Galvanized
Powder Coated Available for an additional cost
*ADA Cane Stops available by request
only.
RAL 9005
Flat Black
RAL 9003
RAL 2004
RAL 1023
Bright Yellow
RAL 6016
RAL 6018
RAL 6005
RAL 5005
RAL 5015
Purple
RAL 7011
RAL 7042
RAL 9007
RAL 1001
RAL 8014
Bronze
RAL 3003
RAL 3005
Installation
Methods
Each upright has two ¼” plate feet that accept 3/8” wedge
anchors.
Examples of the rack in use
American Bicycle Security Company
Page 1 of 5
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865
www.ameribike.com
Email: [email protected]
Dero Decker
Setback Configurations
Single Sided
American Bicycle Security Company
Page 2 of 5
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865
www.ameribike.com
Email: [email protected]
Dero Decker
Setback Configurations
Double Sided
American Bicycle Security Company
Page 3 of 5
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865
www.ameribike.com
Email: [email protected]
Dero Decker
Installation Instructions
Single Sided
1. Refer to setback diagrams before installation to ensure sufficient space.
Installation surface must be concrete of suitable strength. If surface is not
level, contact ABS representative for workable solution.
Tools Needed:
2. Place the Uprights in position and secure
with (4) ½” x 3.75” wedge anchors. At least
1.25” of wedge anchor threads should remain
above the concrete. The Lower Tray Mount
should be placed on the front side of the
Upright and secured with the existing wedge
anchors.
Hammer drill
Masonry bit, 3/8”, 1/2”
Hammer
Socket wrench
Sockets, 9/16”, 3/4”
Socket extension, 4-6”
Hex wrench, 3/16”
Tape measure
Chalk line
Marker
Level
3. Place the lower Cantilever Assembly on the lower
Upright position and secure with (4) ½” x 1.25” carriage
bolts, ½” washers, and ½” nylock nuts.
4. Do the same for the upper Cantilever Assembly.
American Bicycle Security Company
Page 4 of 5
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865
www.ameribike.com
Email: [email protected]
Dero Decker
5. Place the bottom Lower and Upper Trays in position
and secure at the rear with (1) 3/8” x 1” carriage bolt,
3/8” washer, and 3/8” nut each. Secure at the front with
(1) 3/8” x 3” wedge anchor
each.
6. Continue to the next section and repeat the previous
steps
7. After all sections are installed; pull the upper trays out one at a
time to ensure smooth operation. If some trays lower too far and
hit the ground, two set screws at the end of the cantilever can be
tightened to stop the tray sooner.
American Bicycle Security Company
Page 5 of 5
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865
www.ameribike.com
Email: [email protected]
">
