Avocor VTF-7510 User Manual

PDF

Document

AVF-7510 Super-slim UHD LED Display*
Model AVF-7510 Installation/Operation Manual
*Formally known as VTF-7510
COPYRIGHT AND TRADEMARKS:
&copy; Copyright 2016. This document contains proprietary information protected by copyright, trademark and
other intellectual property laws. All rights are reserved. No part of this manual may be reproduced by any
mechanical, electronic or other means, in any form, without our prior written permission.
The trademarks reproduced in this document and used on the products are either owned or licensed by us, or
by their respective holders. You may not reproduce or use the trademarks without our prior written consent.
2
Important Safety Instructions

Before using this display, please read this user manual thoroughly to help protect against property
damage and to ensure your personal safety and the safety of others.

Be sure to observe the following instructions.

For your safety, be sure to observe the warnings located in this manual.

For installation or adjustment, please follow the instructions in this manual and refer all servicing to
qualified service personnel.
Safety Precautions

If smoke or a peculiar smell comes from the display, remove the power plug from the outlet immediately.

Failure to do so may result in fire or electrical shock. Contact your dealer for inspection.

If the display has been turned on but there isn’t a picture, remove the power plug from the outlet
immediately.

Failure to do so may result in fire or electrical shock. Contact your dealer for inspection.

If water is spilled or objects are dropped inside the display, remove the power plug from the outlet
immediately.

Failure to do so may result in fire or electrical shock. Contact your dealer for inspection.

If the display is dropped or the cabinet is damaged, remove the power plug from the outlet immediately.

Failure to do so may result in fire or electrical shock. Contact your dealer for inspection.

To turn off the power of the display, press “O” on the main power switch at side of display.

The power standby/on indicator will go off and the display cannot to be turned on/off by using the
POWER button on the remote control. (To turn on/off the display by the remote control, press the main
power switch again and light the power standby/on indicator.)

When turning off the display by pressing the POWER button on the remote control, the main power
of the display is not turned off completely.

To disconnect power completely, remove the power plug from the outlet.

If the power cord or plug is damaged or becomes hot, turn off the main power switch of the display,
make sure the power plug has cooled down and remove the power plug from the outlet.

If the display is still used in this condition, it may cause fire or electrical shock. Contact your dealer for
replacement.
3
Installation

Don't install in a high-temperature environment.

If the display is used in high-temperature or in direct sunlight, it may cause the case or other parts to
become distorted or damaged, resulting in overheating or electrical shock.

Don't install in a high-humidity environment.

This may cause overheating or electrical shock.

Don't install near any heat sources such as radiators, heat registers, stoves, or other apparatus that
produce heat.

This may cause fire or electrical shock.

Don't overload outlets or cables beyond electrical capacity.

Don't use extension cords as it may cause fire or electrical shock.

Don't insert the power plug into an outlet other than 100~240V AC.

This may cause fire or electrical shock.

Don’t use a damaged power plug or worn outlet.

Don’t insert an improper power plug it may cause fire or electric shock.

Don't place the display on an unstable shelf or surface.

The display may fall, causing injury. Please install on a horizontal, stable, level surface.

Don't place objects on the display.


If the display is covered or the vents are blocked, the display could overheat and cause a fire.

If metal or liquid gets into the display, it may cause fire or electrical shock.

Do not put heavy objects on the display as they may fall, causing injury.

Please keep a 10 cm minimum distance between the display and the wall for sufficient ventilation.
Don't move the display when it is connected to the power cord and AV cables.

When moving the display, make sure to remove the power plug and cables from the outlet or
source.

When unpacking or carrying the display, at least 2 people are needed. Make sure the display is
carried upright.

Transport the display upright. Avoid placing the display face up or down.

Handle the display gently. Do not drop.
4
Use

If you encounter a problem during installation, please contact your dealer for assistance. Don’t repair or
open the display by yourself.

Failure to do so may result in fire or electrical shock. Contact your dealer for inspection.

Protect and correctly use the power cord/plug.

Don't pinch the power cord/plug between hard surfaces.

Don't step on the power cord/plug.

Before inserting the power plug into the wall outlet, connect the power cord to the display.

Don't operate the display with a damaged power cord or it may damage the display.

Using extension cords (not recommended)

If an extension cord must be used, ensure the voltage rating exceeds the max power consumption of the
display. If the voltage rating is less than the display, it will cause the extension cord to overheat.

If there is thunder or lightning, don’t touch the display or the power plug.

This may cause an electric shock.

Don’t use any kind of liquid on the display.

If liquid is spilled on the display, remove the power and ask qualified service personnel to check the
display.

If the liquid gets on the display’s screen, please clean it with a dry and soft cloth immediately.

Don’t use any harsh chemical on the display.

If metal or liquid gets into the display, it may cause a fire or an electrical shock.

Don’t install or remove the power plug with wet hands.

This may cause an electrical shock.

If the display will not be used for a long period of time, unplug the display.

This may cause premature wear of electrical components or fire.

Don’t press on the LCD panel.

This may cause personal injury or panel damage.

Don't push or shake the display.

This may cause damage or injury.

If the glass of the display panel is broken, liquid may escape. Please don't touch the liquid.

If liquid get into your eyes or touches your skin, wash with the clean water and seek medical
attention immediately.

Precautions with the remote control batteries

Please only use approved AAA type batteries.

Please be sure to insert batteries by matching the + and -.

Don’t recharge, heat, disassemble, short or throw batteries into a fire.
5

Don’t mix a new battery with a used one.

Don’t mix different types of batteries together (only use the specified type). it may cause burn and
injury.
Cleaning

If dust has collected on the power plug, removed the plug from the outlet and clean off the dust.

Dust build-up may cause a fire.

Take off the power plug before cleaning.

Failure to do so may result in electrical shock or damage.

Cleaning the surface of the display

When the surface of the display becomes dirty, please wipe the surface lightly with a soft clean
cloth.

If the surface requires additional cleaning, lightly moisten the cloth.

Do not to let any kind of liquid enter the display as it may cause electrical shock or damage.

Do not clean the display with alcohol, solvents or ammonia, as this could damage the display.
6
Warnings
Use

Do not use the display lying flat on its back.

Transport the display upright with proper packaging. Avoid placing the display face up or down. Be
careful not to bump into the display.

Do not send a static (non-moving) image to the display, or it may cause image ‘burn-in’ or image
retention.

“Burn in” and/or image retention is not covered under warranty.

Make sure to change the image on the display periodically. It is recommended to (1) turn off the display
for at least 6 hours after 18 hours of usage in a 24 hour period to help avoid image retention and (2) to
turn the “IRFM” function to “ON” in the OSD menu (under “Advanced Settings”).
Exemptions

This product isn’t warranted for any damage caused by natural disaster (such as earthquake, thunder,
etc.), fire, acts by third parties, accidents, owner’s intentional misuse and fault, or use in other improper
conditions.

This product isn’t warranted for incidental damages (such as profit loss or interruption in business,
modification or erasure of record data, etc.) caused by use or inability to use of this product.

This product isn’t warranted for any damage caused by inappropriate operation, or from not following
the user manual.

This product isn’t warranted for any damage caused by misuse or malfunction through simultaneous use
of this product and the connected equipment or software.

This product isn’t warranted for any damage caused by neglect of the instructions described about
installation.

This product isn’t warranted for any damage caused by improper installation.

This product isn’t warranted for any damage caused by disassembly, modification or repair by nonauthorised service centre or people.
7
Compliance Information
DECLARATION OF CONFORMITY:
AVOCOR hereby declares that the Product's Model Number:
AVF-7510
Conform with the provisions of:

FCC:
FCC CFR Title 47 Part 15 Subpart B Class A, CISPR 22
ANSI C63.4
ICES-003 Issue 5

CE:
1999/5/EC
EN 55022
EN 55024
EN 61000-3-2
EN 61000-3-3

cTUVus:
UL 60950-1
CAN/CSA-C22.2 No. 60950-1-07

CB:
IEC 60950-1
FCC PART 15:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
CAUTION:
Any changes or modifications not expressly approved by the grantee of this device could void the user's
authority to operate the equipment.
RF Exposure Warning:
This equipment must be installed and operated in accordance with provided instructions and the antenna(s)
used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons
and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and
installers must be provide with antenna installation instructions and transmitter operating conditions for
satisfying RF exposure compliance.
8
INDUSTRY CANADA (ICES-003):
CAN ICES-3 (A)/NMB-3(A)
PRODUCT DISPOSAL:
The Product contains small amounts of tin, lead and / or mercury. Disposal of these materials maybe regulated
due to environmental considerations.
DISPOSAL OF OLD ELECTRICAL AND ELECTRONIC EQUIPMENT (Applicable throughout the European Union and
other European countries with separate collection programs)
This symbol found on your product or on its packaging, indicates that this product should not be
treated as household waste when you wish to dispose of it. Instead, it should be handed over to
an applicable collection point for the recycling of electric al and electronic equipment. By
ensuring this product is disposed of correctly, you will help prevent potential negative
consequences to the environment and human health, which could otherwise be caused by
inappropriate disposal of this product.
The recycling of materials will help to conserve natural resources. This symbol is only valid in the European
Union. If you wish to discard this product, please contact your local authorities or dealer and ask for the
correct method of disposal.
9
Notes
10
Table of Contents
Important Safety Instructions .............................................................................................................. 3
Safety Precautions ....................................................................................................................................... 3
Installation .................................................................................................................................................... 4
Use ................................................................................................................................................................ 5
Cleaning ....................................................................................................................................................... 6
Warnings .............................................................................................................................................. 7
Use ................................................................................................................................................................ 7
Exemptions ................................................................................................................................................... 7
Compliance Inform ation .................................................................................................................... 8
T able of Contents ............................................................................................................................... 11
List of Figures ..................................................................................................................................... 13
1. Introduction ................................................................................................................................... 15
About This Manual....................................................................................................................................... 15
Target Audience ........................................................................................................................................ 15
Textual and Graphic Conventions ......................................................................................................... 15
Using This Manual ........................................................................................................................................ 16
Description, Features and Benefits ............................................................................................................. 17
Key Features and Benefits .......................................................................................................................... 17
Touch Capability: ........................................................................................................................................ 17
Parts List ........................................................................................................................................................... 18
2. Controls and Functions................................................................................................................. 19
Display at a Glance .................................................................................................................................. 19
Input Panel ................................................................................................................................................ 21
Remote Control Unit................................................................................................................................... 23
3. Installation ..................................................................................................................................... 25
Remote Control .......................................................................................................................................... 25
Notes on Batteries ....................................................................................................................................... 25
Notes on Remote Control Operation......................................................................................................... 25
Quick Setup ................................................................................................................................................. 26
Installation Considerations ....................................................................................................................... 26
Ambient Light............................................................................................................................................... 26
Ambient Heat ............................................................................................................................................. 26
Ventilation .................................................................................................................................................... 27
Mounting the Display ................................................................................................................................. 28
Connections to the Display ........................................................................................................................ 28
Connecting a Control System or PC: ........................................................................................................ 29
Connecting Source Components to the Display ...................................................................................... 31
Turning on the Power .................................................................................................................................. 33
Changing the OSD Language ................................................................................................................... 34
Enabling the Touch Screen ....................................................................................................................... 34
Connecting the Touch Screen Controller Host Computer to the Display .............................................. 34
Software Installation .................................................................................................................................... 35
4. Op er a tion..................................................................................................................................... 39
Using the On-Screen Menus ...................................................................................................................... 39
Input Menu ................................................................................................................................................... 41
11
Picture Menu ................................................................................................................................................ 42
Audio Menu ................................................................................................................................................. 44
OSD Settings Menu...................................................................................................................................... 45
Setup Menu ................................................................................................................................................... 46
Advanced Setup Menu .................................................................................................................................. 47
Communication Menu ............................................................................................................................... 49
Information ................................................................................................................................................... 50
5 . M ainten ance and Troubleshooting .................................................................................... 51
Maintenance.............................................................................................................................................. 51
Troubleshooting ......................................................................................................................................... 51
6. External Control ............................................................................................................................ 54
Serial Communications ............................................................................................................................ 54
RS-232 Connection and Port Configuration .......................................................................................... 54
Command and Response Format........................................................................................................... 54
Command and Response Examples ....................................................................................................... 55
Serial Command List .................................................................................................................................... 55
Using Discrete IR Codes .............................................................................................................................. 64
IR Command Protocol ............................................................................................................................... 64
IR Control Code List ..................................................................................................................................... 65
7. Specifications ................................................................................................................................ 67
Supported Timings ........................................................................................................................................ 69
Overall Dimensions ..................................................................................................................................... 71
Appendix I: Moving and Carrying Notice ...................................................................................... 73
Moving the Display: ................................................................................................................................... 73
Carrying the display: ................................................................................................................................. 73
Appendix II: Installing a Wall Mount ............................................................................................... 74
Appendix III: Installing an OPS Module .......................................................................................... 75
Appendix IV: Wall Mount Safety Notes ........................................................................................... 76
Appendix V: Power/ PC Key Operations ....................................................................................... 78
Appendix VI: Ethernet Remote Control Settings ............................................................................ 79
Configurations ............................................................................................................................................ 79
Administrator ................................................................................................................................................ 79
TCP Mode ..................................................................................................................................................... 82
UDP Mode .................................................................................................................................................... 83
UART .............................................................................................................................................................. 84
SMTP .............................................................................................................................................................. 85
Reset Device ................................................................................................................................................ 86
12
List of Figures
Figure 2-1. Display Rear/ Side / Front View ........................................................................................................................... 19
Figure 2-2. Display Input Panel Side/Front View .................................................................................................................. 21
Figure 2-3. Display Remote Control Unit ............................................................................................................................... 23
Figure 3-1. Ventilation Requirements for Enclosure Mounting........................................................................................... 27
Figure 3-2. RS-232 Control System Connection .................................................................................................................... 29
Figure 3-3. Ethernet Connection ............................................................................................................................................. 30
Figure 3-4. DisplayPort Source Connection .......................................................................................................................... 31
Figure 3-5. HDMI Source Connections ................................................................................................................................... 32
Figure 3-6. VGA Source Connections ................................................................................................................................... 33
Figure 3-7. Touch Screen Controller (USB) Connection ...................................................................................................... 34
Figure 4-1. OSD Menu Structure .............................................................................................................................................. 40
Figure 7-1. AVF-7510 Display Dimensions ................................................................................................................................ 71
13
Notes
14
1. Introduction
About This Manual
This Owner’s Manual describes how to install, set up and operate the AVOCOR Series LED Display.
Throughout this manual, the AVOCOR Series LED Display is referred to as the “display”.
Target Audience
The manufacturer has prepared this manual to help installers and end users get the most out of the display.
The manufacturer has made every effort to ensure that this manual is accurate as of the date it was printed.
However, because of ongoing product improvements and customer feedback, it may require updating from
time to time.
Textual and Graphic Conventions
Text Conventions: The following conventions are used in this manual, in order to clarify the information and
instructions provided:

Remote and built-in keypad button identifiers are set in upper-case bold type; for example, “Press EXIT to
return to the previous menu.”

Computer input (commands you type) and output (responses that appear on-screen) is shown in
monospace (fixed-width) type; for example: “To change the aspect ratio to Letterbox, type 07 00 02 41
53 50 03 08 &lt;Enter&gt;.”

All keys with functional names are initial-capped, set in bold type and enclosed in angle brackets. These
keys are the following: &lt;Enter&gt;, &lt;Spacebar&gt;, &lt;Control&gt;, &lt;Esc&gt; and &lt;Tab&gt;. &lt;Enter&gt; indicates that you
may press either the RETURN or ENTER key on your keyboard if it has both keys.

In addition to these conventions, underlining, bold face and / or italics are occasionally used to highlight
important information, as in this example:
NOTE
A carriage return must be used after each command or string.
15
Graphic Conventions: These symbols appear in numerous places throughout the manual, to emphasise points that
you must keep in mind to avoid problems with your equipment or injury:
TIP
TIPS highlight time saving short cuts and helpful guidelines for using certain features.
NOTE
NOTES emphasise text with unusual importance or special significance. They also provide
supplemental information.
CAUTION
CAUTIONS alert users that a given action or omitted action can degrade performance or
cause a malfunction.
WARNING
WARNINGS appear when a given action or omitted action can result in damage to the
equipment, or possible non-fatal injury to the user.
DANGER!
DANGER appears when a given action can cause severe injury or death.
Using This Manual
Use the following table to locate the specific information you need in this manual.
If you need...
... Turn to page:
General information about the AVOCOR Series LED Display
17
Installation instructions
25
First-time configuration instructions
34
Advanced configuration instructions
47
Troubleshooting tips
51
Product specifications
67
16
Description, Features and Benefits
The AVF-7510 is a ultra-high definition touch display that supports a full 3840x2160 @ 60 Hz resolution and can
display 1.073 billion colours.
They combine ultra-high resolution and unparalleled image quality with configurable I/O in a large-format
display for a wide range of digital signage and control-room applications.
Key Features and Benefits
The display offers these key features and benefits:

Up to 3840x2160 @ 60 Hz resolution

High-resolution, high-speed InGlass™ touch sensing for up to 10 simultaneous touches

Can display up to 4 video sources simultaneously

(4) HDMI v1.4 inputs and DisplayPort 1.2 input with High-bandwidth Digital Content Protection (HDCP),
VGA, RS-232, USB 2.0/3.0, Touch USB and LAN connections

An optional OPS (Open Pluggable Specification) slot

Full-range internal speakers

Signal source auto detection

Flexible ON/OFF scheduler

Low power consumption
Touch Capability

Precise, highly responsive touch technology

High touch sensitivity – no pressure required

Any touch: finger, gloved hand or pointer

Calibrated easily by software tools as attached

Windows 7/8/10 compliant

One USB cable for easy Plug-and-Play operation
17
Parts List
Your display is shipped with the following items. If any items are missing or damaged, please contact your
dealer or Customer Service.

AVOCOR UHD LED Display

Remote Control Unit and Batteries

AC Power Cord

Touch Stylus

RF Antenna

USB Key – Multi-Touch Drivers &amp; User Manual

USB Cable - 3 Metres

HDMI Cable - 3 Metres

VGA Cable - 3 Metres
18
2. Controls and Functions
Display at a Glance
M E NU/
CE
SOUR
Figure 2-1 shows the key display components, and the paragraphs that follow describe them.
Figure 2-1. Display Rear/ Side / Front View
1.
MAIN POWER SWITCH
Connects or disconnects the display panel from the AC power source.
2.
HANDLE
Always use the handles and lower handlebars (AVF-6510) when carrying the display.
DO NOT touch / hold the screen face or the lower front panel.
3.
STATUS LED
Solid orange: display in standby mode
Blinking orange: display on, no input detected
Off: main power switch off
Solid green: display on, input detected
19
4.
KEYPAD
You can use the keypad instead of the remote control unit to operate the on-screen display (OSD)
controls. The keypad operates as follows:
POWER
Press the button to turn off/on the monitor screen. (Refer to Appendix V for detailed operations.)
SOURCE
Press the button to select a media source. When using WIN PC, pressing this button will return to the
previous source selected.
Win10 PC
Press the button to turn on/off the Win10 PC that's built in the display. (Refer to Appendix V for detailed
operations.)
VOLUME DOWN
/ UP
Press these two buttons to lower or increase the volume.
FREEZE
Press the button to freeze the screen. Press again to release it.
BLANK
Press the button to blank the screen.
20
Input Panel
Figure 2-2 shows the display input panel.
Figure 2-2. Display Input Panel Side/Front View
21
No.
Connector
1
RS232C In
A female, 9-pin D-sub connector for interfacing with a PC or home theatre
automation/control system.
2
LAN Port
An RJ-45 connector for interfacing with a PC or home theater automation/control system via
a Cat 5 cable.
3, 19
Hub In (Touch USB)
Two standard, Type-B USB port for connecting media sources to the display.
Note: The USB cable used for the front Hub In connector can be up to 3 metres in length,
while the one used for the rear Hub In connector can be up to 5 metres in length.
4
RF Antenna
Established a network connection for the display to go online via WIFI.
5
OPS (Open Pluggable Specification) Slot
An optional OPS slot for connecting an internal PC to display 4K content.
6, 20
7
8, 18
WIN PC USB
Two standard USB connectors of the Windows mini PC for connecting external multimedia
player devices.
WIN PC Ethernet
An RJ-45 connector for interfacing with the built-in Windows PC via a Cat 5 cable.
HDMI
HDCP-compliant digital video input for connecting HDMI sources.
9
DisplayPort
DisplayPort 1.1a and DisplayPort-HDCP 1.1 compliant, SD/HD input for connecting SDTV, EDTV
or HDTV component video sources.
10
VGA In (15-pin D-Sub)
Connects components that have RGB or component output jacks, such as a personal
computer or external DTV decoder (a break-out c able is needed for BNC-type connection).
11
PC Audio In
Connects the audio output from a personal computer here.
12
IR Extender
Connects an IR Extender cable from this input.
13
Audio Out
Connects external, powered speakers or an external audio receiver/amplifier.
14
SPDIF Out
Connects external and powered digital speakers or audio receiver/amplifier.
15
Service Port
A standard USB connector for connecting the USB stick that comes with the package to
upgrade firmware.
16
OPS USB
A standard USB connector of the OPS slot for connecting external multimedia player devices.
17, 21
HUB USB
Two standard USB connectors for connecting external media, keyboard, keyboard or mouse.
22
Remote Control Unit
Figure 2-3 shows the display remote control, and Table 2-1 describes its functionality.
Figure 2-3. Display Remote Control Unit
23
Table 2-1. Remote Control Button Descriptions
Label
Description
Turns the monitor on and off.
(Refer to Appendix V for detailed operations.)
Selects a media source.
Turns on WIN PC, and selects WIN PC input source.
(Refer to Appendix V for detailed operations.)
Blanks the screen. Press any key to restore.
Freezes the screen. Press again to restore.
Turns off the sound.
Increases or decreases the volume by pressing the + and - keys.
Selects standard settings.
Opens the monitor’s on-screen menu system.
When the menu system is already open, pressing this butt on will
select the previous submenu.
Navigates through submenus and settings.
ENTER
EXIT
AUTO
SCALING
Selects highlighted menu choices
Closes the menu system
Auto adjustment of VGA source
Selects each aspect ratio, in sequence: Full Screen,
Native, Letter Box and Pillar Box
24
3. Installation
NOTE
Installation must be performed by a qualified custom video installation specialist.
Remote Control
To install batteries in the remote control:
1.
Press down the tab on the cover and pull the cover up.
2.
Insert the included batteries. Ensure that the polarities correctly match the
the battery component.
3.
Insert the lower tab of the cover into the opening, and press down the cover until it clicks in place.
and
markings inside
Notes on Batteries
Make sure that the battery polarities are correct when installing the batteries.

Do not mix an old battery with a new one or different types of batteries.

If you will not use the remote control for a long time, remove the batteries to avoid damage from battery
leakage.

Do not expose batteries to excessive heat such as from sunshine, fire or the like.
Notes on Remote Control Operation
Make sure that there is nothing obstructing the infrared beam between the remote control and the IR receiver
on the display.

If the effective range of the remote control decreases, or it stops working, replace the batteries with new
ones.

The remote control may fail to operate if the infrared remote sensor is exposed to bright sunlight or
fluorescent lighting.

Ambient conditions may possibly impede the operation of the remote control. If this happens, point the
remote control at the display, and repeat the operation.
25
Quick Setup
Table 3-1 gives a quick overview of the display installation process. The sections following this one provide
detailed instructions.
Table 3-1. Installation Overview
Step
Procedure
For Details,
Refer to page...
1
Mount the display(s) on a wall (optional)
28
2
Connect other external equipment to the display (optional):
Automation/control system (RS-232, Ethernet)
28
3
Connect signal sources to the display
31
4
Apply power to the display
33
5
Change the OSD language (optional)
34
6
Perform touch screen-specific installation and configuration tasks
(AVOCOR):
Connect touch screen controller host computer to the display
35
7
Display calibration - adjust the following for each input:
 Aspect ratio
 Brightness
 Contrast
 Colour temperature and white balance
 Color level
 Tint
 Input position
41
Installation Considerations
Proper installation of your display will ensure a satisfying viewing experience. Whether a display is installed
temporarily or permanently, the following should be taken into account to ensure the best performance of
the display.
Ambient Light
In general, minimise or eliminate light sources directed at the screen. Contrast ratio in your images will be
noticeably reduced if light directly strikes the screen, such as when a shaft of light from a window or floodlight
falls on the image. Images may then appear washed out and less vibrant. Direct sunlight may affect touch
operation.
Ambient Heat
Keep the ambient temperature constant and below 35&deg;C (95&deg;F). Keep the display away from heating and / or
air conditioning vents.
26
Ventilation
If you are mounting the display in an enclosure, leave sufficient space on all sides between it and surrounding
objects, as shown in Figure 3-1. This allows heat to disperse, maintaining the proper operating temperature.
Wall
50 mm (2&quot;)
50 mm (2&quot;)
Wall
Figure 3-1. Ventilation Requirements for Enclosure Mounting
27
Mounting the Display
You can mount the display on a wall.
If you do decide to wall-mount the display, ensure that the wall-mount bracket is installed according to the
instructions included with it. The wall must be capable of supporting a redundant weight factor three (3) times
the weight of the display, or be reinforced.
We recommend that this be done by a custom installation specialist.
NOTE
Use only the approved wall-mount kit designed for your display.
Connections to the Display
Proceed as follows to connect the display to your video sources, external controller(s) – if present – and AC
power.
When connecting your equipment:

Turn off all equipment before making any connections.

Use the correct signal cables for each source.

For best performance and to minimise cable clutter, use high-quality cables that are only as long as
necessary to connect two devices. (Don't use a 7m cable when a 1.8m cable will suffice.)

Ensure that the cables are securely connected. Tighten the thumbscrews on connectors that have them.
28
Connecting a Control System or PC:
RS232 Connection
Use a straight-through RS-232 cable with a 9-pin male connector to connect a PC or control/ automation
system (if present) to the RS-232 port on the display; see Figure 3-2.
For more information about using this connection, refer to External Control on page 54.
Figure 3-2. RS-232 Control System Connection
29
Ethernet Connection
Use a standard Ethernet cable with an RJ-45 male connector to connect a PC or control/automation system
(if present) to the Ethernet port on the display.
For more information about using this connection, refer to External Control on page 54.
Figure 3-3. Ethernet Connection
30
Connecting Source Components to the Display
Connect your video sources to the display as shown and described in the sections that follow.
DisplayPort Source Connection: See Figure 3-4.
Figure 3-4. DisplayPort Source Connection
31
HDMI Source Connections: See Figure 3-5.
TIP
NOTE
Use the HDMI inputs whenever possible. This ensures the highest video quality
because the signal is carried in the digital domain throughout the entire signal path,
from source component output into the display.
This display supports the VESA Display Data Channel (DDC) standard. This standard
provides “Plug and Play” capability; the display and a VESA DDC-compatible
computer communicate their setting requirements, allowing for quick and easy
setup.
In order for Plug and Play to work correctly, you must turn on the display before you
turn on the connected computer.
Figure 3-5. HDMI Source Connections
32
VGA Source Connection: Connect a personal computer or other RGB source to the VGA input as shown in
Figure 3-6.
NOTE
Refer to Supported Timings on page 69 for a list of compatible input signals.
Figure 3-6. VGA Source Connections
Turning on the Power
1.
Turn on your source components.
2.
Plug the female end of the supplied power cord into the AC receptacle on the side of the display (AC
100V ~ 240V). See Figure 2-2.
3.
Connect the other end to your AC power source.
4.
Turn on the main power switch at the side of the display (see Figure 2-1). The power indicator lights
orange to indicate that the display is in “standby” mode.
5.
Press the power button (
(
6.
) on the remote control to turn on the display or press the power button
) on the keypad.
After a brief warm-up period, the display will display an image.
NOTE
If there's no input signal for a period of time, the display will
automatically go into power saving (sleep) mode.
33
Changing the OSD Language
The display OSD language is initially set to English, but can also display the menus in different languages.
To change the OSD language:
1.
Press MENU.
2.
Select Basic Settings from the Main Menu.
3.
Select OSD Language from the Basic Settings Menu.
4.
Press
or
to select the desired language and press ENTER. The change takes effect immediately.
Enabling the Touch Screen
Before setting up your display to support touch screen capability, ensure that:

The touch screen controller host computer is turned off.

The display is turned on.

The video output from the computer is connected to a video input on the display. See Figure 3-4, Figure
3-5 or Figure 3-6.
Connecting the Touch Screen Controller Host Computer to the Display
1.
Connect the signal cable witch display, and then turn on the display.
2.
Connect the USB cable with display and the computer; connect one side of USB cable (Type-B USB
connector) on the display side.
3.
Connect the other side of USB cable (Type-A USB) to the USB port on computer. See picture below.
4.
Then turn on the computer.
5.
When USB cable connected, then wait for 5 seconds and the touch function is ready to go. It can be
activated by pen, finger, or any other pointer.
USB Type &quot;B&quot; Plug
USB Type “A” Plug
to PC or USB Hub
Figure 3-7. Touch Screen Controller (USB) Connection
34
Software Installation
This driver is not needed for any touch functionality, but is needed in order to perform firmware upgrade.
Automatic Driver Installation
If the automatic driver installation starts, please allow it to run until completion in order to not disrupt the
automatic process. Note that the icon may be hidden in the notification area, and that the procedure may
take several minutes.
Clicking on the pop-up ballon at this point would show
Fully expanded, the view in the Device Manager should look like this (View --&gt; Devices by connection):
If the automatic installation fails to find the driver, or if automatic driver installation is disabled, or if there is no
Internet connection, this is what you will typically see when connecting a FlagFrog touch device.
35
Clicking on the pop-up ballo would show
In the Device Manager, the view would be (again, use View --&gt; Devices by connection):
In this case, please proceed with Manual Driver Insatllation.
Manual Driver Installation
If the automatic driver installation failed for any of the reasons listed above, or if you would like to install the
driver without having a FlatFrog touch device connected to the computer, the driver can be installed
manually.
The driver provided with this upgrade package was downloaded from http://catalog.update.microsoft.com
(requires Internet Explorer) and is called “Microsoft – Other hardware – WinUsb Device” (version 1.1.0.0 from
2012-08-30).
Manual Driver Installation - Device Connected
1.
Extract the firmware upgrade .zip file (right-click --&gt; Extract all...) to the Desktop.
2.
Open the Device Manager and locate the &quot;HID/DFU&quot;device with the yellow exclamation mark.
3.
Right-click and select &quot;Update Driver Software...&quot;
36
4.
Select &quot;Browse my computer for driver software&quot; and select the extracted folder from step 1 and follow
the instructions.
5.
If step 4 was unsuccessful, then Windows failed to automatically associate the driver with the device.
6.
Choose &quot;Let me pick from a list if device drivers on my computer&quot; in step 4, scroll all the way down to
&quot;Universal Serial Bus devices&quot; and click Next.
37
7.
Select the WinUsb device driver, and click Next. (If the WinUsb device driver is not in the list, please follow
the steps under &quot;Manual Driver Installation - Device Not Connected&quot; first).
Manual Driver Installation - Device Not Connected
1.
Extract the firmware upgrade .zip file (right-click --&gt; Extract all...) to the Desktop.
2.
Navigate to the &quot;support&quot; folder.
3.
Right-click on the install_driver.bat file and select &quot;Run as administrator&quot; and follow the instructions.
38
4. Operation
Using the On-Screen Menus
To display the on-screen menus, press MENU on the remote control (Figure 2-3) or built-in keypad (Figure 2-1).
To select a sub-menu, use the
and
To select a menu item, use the
press ENTER.
buttons to highlight it. Then, press
and
buttons to highlight it. Then, press
to enter that sub-menu.
or
to adjust that setting and
The OSD menus are arranged hierarchically, as shown in Figure 4-1. Depending on the selected input source
and signal characteristics, some menu options may not be available.
Main Menu
Input
SubMenu
Value
Main Input
VGA; DisplayPort; HDMI1; HDMI2; HDMI3; HDMI4; OPS; Front
HDMI; PC
AutoScan
Off; Main; PxP; All
PiP Mode
Off; PiP; PbP; 3Window; 4Window
Sub1 Input
VGA; DisplayPort; HDMI1; HDMI2; HDMI3; HDMI4; OPS; Front
HDMI; PC
Sub2 Input
(same as above)
Sub3 Input
(same as above)
PiP Size
Small; Mid; Large
PiP Position
TopR; TopL; BotR; BotL
Swap
Picture
Audio
Rename Source
Rename input sources.
Picture Format
Main: Full Screen/Letterbox/ 4:3/1:1;
Scheme
User, Vivid, Cinema, Game, Sport
Contrast
0, 1, 2, ...., 50, ....100
Brightness
0, 1, 2, ...., 50, ....100
Sharpness
0, 1, 2, ...., 50, ....100
Hue
0, 1, 2, ...., 50, ....100
Saturation
0, 1, 2, ...., 50, ....100
Backlight
0, 1, 2, ...., 50, ...., 80, ....100
Colour Temp &amp;
Gamma
5000K; 6500K; 7500K; 9300K; User; off; 2.2
HDMI RGB Range
Auto; Full; Limited
Volume
0~100
Treble
-6~6
Bass
-6~6
Balance
-6~6
Internal Speaker
On; Off
Audio Source
Line-In ; DisplayPort ; HDMI1 ; HDMI2 ; HDMI3 ; HDMI4 ; OPS;
Front HDMI; PC
39
Main Menu
SubMenu
OSD Settings
Value
Horizontal
0~100
Vertical
0~100
Transparency
Off; 1~4
OSD Timeout
5s; 10s; 20s; 30s; 60s
Language
English, French, German, Dutch, Hungarian, Slovenian,
Serbian, Croatian, Danish
Splash Screen
On; Off
Auto Adjustment
Setup
Adv. Setup
H.Position
0~100
V.Position
0~100
Phase
0~100
Clock
0~100
Zoom
10 steps
Power LED
On; Off
Real Time Clock
User Mode; Workday Mode; Everyday Mode
Win10 PC Power
Mode
Auto, Manual, Off
Smart Light Control
Off; DCR; Light Sensor
IRFM
On; Off
Noise Reduction
Off; Low; Medium; High
Wake Up From Sleep
VGA Only; Digital, RS232. Ethernet; Never Sleep
DP Ver.
1.1; 1.2
EDID Setup
HDMI: 4K2K/1080P; DP: 4K2K/1080P
Touch Control
Auto; OPS; USB Touch 1; USB Touch 2; PC
Firmware Update
Factory Reset
Communication
Information
NOTE
RS232 Baud Rate
115200; 38400; 19200; 9600
Enable Network
Yes; No
IP Address Settings
Please refer to Communication Menu section for details
Power Status Alert
Yes; No
Source Status Alert
Yes; No
Signal Lost Alert
Yes; No
Load Default
Yes; No
Device MAC
Shows the MAC address of the device
(Timing info)
Shows the name of input source
PC Power Status
Shows the power status of PC
Firmware Version
Shows the firmware version of the monitor
SubMCU Version
Shows the firmware version of the monitor
Serial Number
Shows the Serial Number of the monitor
Default settings appear in bold type.
Figure 4-1. OSD Menu Structure
40
Input Menu
This menu is used for selecting the main input source (Main) and up to three Picture-in-Picture input sources
(Sub1, Sub2 and Sub3). Up to four sources can be displayed at the same time.
Main Input
Select the main input source
Options: VGA, DisplayPort, HDMI1, HDMI2, HDMI3, HDMI4, OPS, Front HDMI, PC
Auto Scan
Select whether the display will automatically scan for a main input source
Options: Off, Main, PxP, All
PiP Mode
Select the PiP (Picture-in-Picture) mode
Options: Off, PiP, PbP, 3Window, 4Window
Sub1 Input
Select the source for the primary PiP window
Options: VGA, DisplayPort, HDMI1, HDMI2, HDMI3, HDMI4, OPS, Front HDMI, PC
Note: This function is only available when PiP Mode is set to PiP, PbP, 3Window
or 4Window
Sub2 Input
Select the source for the secondary PiP window
Options: VGA, DisplayPort, HDMI1, HDMI2, HDMI3, HDMI4, OPS, Front HDMI, PC
Note: This function is only available when PiP Mode is set to 3Window or
4Window
Sub3 Input
Select the source for the tertiary PiP window
Options: VGA, DisplayPort, HDMI1, HDMI2, HDMI3, HDMI4, OPS, Front HDMI, PC
Note: This function is only available when PiP Mode is set to 4Window
PIP Size
Select the size of the primary PiP window
Options: Small, Mid, Large
Note: This function is only available when PiP Mode is set to PiP
PIP Position
Set the position of the primary PiP window
Options: TopR, TopL, BotR, BotL
Note: This function is only available when PiP Mode is set to PiP
41
Swap
Swap the main input source with the primary PiP source
Note: This function is only available when PiP Mode is set to PiP, PbP, 3Window
or 4Window
Rename Source
Rename the input source.
Press ENTER to sele ct the input source you want to rename. Using ▲ or ▼ to
change the character and  or  to move forward/back a position. Then press
MENU and ENTER to save the name. The name can be up to eight characters
(0~9, A~Z, a~z).
Picture Menu
This menu is used for making common image adjustments.
Picture Format
Adjust the picture format of the screen
Options: Full Screen, Letterbox, 4:3, 1:1; Default: Full Screen
Scheme
Press or to select one of the following:
Options: User, Vivid, Cinema, Game, Sport; Default: User
Contrast
Increase or decrease the contrast of picture.
Press  or  to select the desired level, and then press ENTER.
Range: 0~100; Default: 50
Brightness
Increase or decrease the brightness of picture.
Press or to select the desired level, and then press ENTER.
Range: 0~100; Default: 50
Hue
Increase or decrease the green hue.
Press  or to select the desired level, and then press ENTER.
Range: 0~100; Default: 50
Note: This function is not available when displaying PC or graphics sources
42
Saturation
Adjust the brilliance and brightness.
Press or to select the desired level, and then press ENTER.
Range: 0~100; Default: 50
Note: This function is not available when displaying PC or graphics sources
Backlight
Increase or decrease the intensity of the LCD backlight.
Press or to select the desired level, and then press ENTER.
Range: 0~100; Default: 80
Gamma
Select gamma curve
Options: Off, 2.2; Default: 2.2
Colour Temp
Select a colour temperature, or select User to make RGB adjustments.
Options: User, 5000K, 6500K, 7500K and 9300K; Default: 9300K
HDMI RGB Range
Select an RGB range for the HDMI input.
Options: Auto, Full, Limited; Default: Auto
Colour Temperature Settings
Red Gain
Set Colour Temperature to “User Mode” in order to adjust this setting.
Range: 0~100; Default: 100
Green Gain
Set Colour Temperature to “User Mode” in order to adjust this setting.
Range: 0~100; Default: 100
Blue Gain
Set Colour Temperature to “User Mode” in order to adjust this setting.
Range: 0~100; Default: 100
Red Offset
Set Colour Temperature to “User Mode” in order to adjust this setting.
Range: 0~100; Default: 50
Green Offset
Set Colour Temperature to “User Mode” in order to adjust this setting.
Range: 0~100; Default: 50
43
Blue Offset
Set Colour Temperature to “User Mode” in order to adjust this setting.
Range: 0~100; Default: 50
Audio Menu
This menu is used for adjusting volume settings.
Volume
Adjust the sound. Press  or  to select the desired level, and then press
ENTER.
Range: 0~100; Default: 50
Treble
Adjust the sound in high tones (treble). Press  or  to select the desired level,
and then press ENTER.
Range: -6~6; Default: 0
Bass
Adjust the sound in low tones (bass). Press  or  to select the desired level,
and then press ENTER.
Range: -6~6; Default: 0
Balance
Adjust the balance of the left and right speakers. Press  or  to select the
desired level, and then press ENTER.
Range: -6~6; Default: 0
Internal Speaker
Turn the internal speaker on or off
Default: On
Audio Source
Select the audio source for the Main input
Options: Line-In, DisplayPort, HDMI1, HDMI2, HDMI3, HDMI4, OPS, Front HDMI, PC
Default: Line-in
44
OSD Settings Menu
This menu is used to make initial set-up adjustments to the OSD (On-Screen Display) menu and other on-screen
messages.
Horizontal
Adjust the horizontal position of the OSD menu. Press  or  to select the
desired level, and then press ENTER.
Range: 0~100; Default: 50
Vertical
Adjust the vertical position of the OSD menu. Press  or  to select the
desired level, and then press ENTER.
Range: 0~100; Default: 50
Transparency
Adjust the transparency of the OSD menu. Press  or  to select the desired
level, and then press ENTER.
Range: Off, 1~4; Default: Off
OSD Time Out
Adjust the time in seconds before the OSD menu disappears. Press  or  to
select the desired level, and then press ENTER.
Options: 5s, 10s, 20s, 30s, 60s
Default: 30s
Language
Select the OSD language
Options: English, French; German; Dutch; Hungarian; Slovenian; Serbian;
Croatian; Danish
Default: English
Splash Screen
Select whether a splash screen appears when the monitor is powered up
Options: On, Off
Default: On
45
Setup Menu
Auto Adjustment
Force the display to reacquire and lock to the input signal (VGA source only).
This is useful when the signal quality is marginal. Note: This feature does not
continually reacquire the signal.
Options: No, Yes; Default: No
H. Position
Adjust the horizontal position of the image (VGA source only). Press  or  to
select the desired level, and then press ENTER.
Range: 0~100; Default: 50
V. Position
Adjust the vertical position of the image (VGA source only). Press  or  to
select the desired level, and then press ENTER.
Range: 0~100; Default: 50
Phase
Adjust the phase of the displayed signal (VGA source only). Press  or  to
select the desired level, and then press ENTER.
Range: 0~100
Clock
Adjust the clock of the displayed signal (VGA source only). Press  or  to
select the desired level, and then press ENTER.
Range: 0~100
Zoom
Adjust the zoom (overscan) of the image. Press  or  to select the desired
level, and then press ENTER.
Range: 10 steps
Power LED
Enable or disable the status LED
Options: On, Off; Default: On
Real Time Clock
Set the internal clock of the display, and to power on and off the display at
preset times if desired.
Options: User mode, Workday mode, Everyday mode
Default: User mode
Win10 PC Power Mode
Set Win10 PC power mode.
Options: Auto, Manual, Off
Default: Auto
46
Advanced Setup Menu
Smart Light Control
Enable dynamic contrast (DCR) or ambient light sensor
Options: Off, DCR, Light Sensor; Default: Off
IRFM
Create slight frame motion to help avoid image retention
Options: On, Off; Default: Off
Noise Reduction
Reduce random noise in the video content
Options: Off, Low, Medium, High; Default: Off
Wake Up From Sleep
Options: VGA Only, Digital, RS232, Ethernet; Never Sleep
Default: VGA Only
DP Ver.
Select DisplayPort version of the DisplayPort inputs
Options: 1.1, 1.2
Note: DisplayPort 1.2 is the more modern standard and supports 3840x2160 @ 60
Hz resolution. However, sometimes DisplayPort 1.1 is needed for compatibility
with older graphics cards.
EDID Setup
Select EDID (Extended Display Identification Data) of the HDMI and DisplayPort
inputs
Options: 1080p, 4K2K
Note: Use the 1080p setting for the broadest support of lower resolution sources.
Use 4K2K setting to support high resolution sources such as 3840x2160.
Touch Control
Select one of the touch connections, or choose auto detection.
Options: Auto, OPS, USB Touch 1 (front panel), USB Touch 2 (I/O panel), PC;
Default: Auto
Firmware Update
Plug in the USB flash drive and select Yes to proceed with firmware update.
Options: No, Yes; Default: No
To start updating firmware, select Yes to continue.
Options: No, Yes; Default: Yes
Factory Reset
Restore all settings to their default.
Options: No, Yes; Default: No
47
Wake Up from Sleep
By default, the display will enter power saving (Sleep Mode) if no signal is received for 5 minutes. Normally, the
RS-232, DisplayPort, and HDMI inputs are inactive in Sleep Mode, to save power.
To change the behavior of Sleep Mode, change the “Wake up from Sleep” setting in the “Adv. Setup” menu.

VGA Only (default) – The RS-232, DisplayPort, and HDMI inputs are inactive when the display is in sleep
mode. The display will wake up when it receives a signal at the VGA input.

Digital, RS232, Ethernet – The RS-232, DisplayPort and HDMI inputs stay active when the display is in sleep
mode. The display will wake up when it receives a signal at either of the DisplayPort, HDMI, or RS-232
inputs, or via LAN connection.
48
Communication Menu
This menu configures the display’s RS232 and Ethernet communication ports.
Baud Rate
Select the baud rate of the display’s RS232 port
Options: 115200, 38400, 19200, 9600
Default: 19200
Enable Network
Enable the display’s built-in Ethernet port
Options: No, Yes
Default: No
IP Address Settings
Enable Dynamic IP mode or set the static IP address of the display’s Ethernet
port
Power Status Alert
Enable an automatic alert when the display is powered down
Options: No, Yes
Default: No
Source Status Alert
Enable an automatic alert when the source is changed
Options: No, Yes
Default: No
Signal Lost Alert
Enable an automatic alert when the video signal is lost
Options: No, Yes
Default: No
Load Default
Load default communication settings
Options: No, Yes
Default: No
Device MAC
Display the MAC address of the device.
49
Network Settings
To assign an IP address to your display, access the IP Address Settings Menu in the Communication Menu.
Consult your system administrator if you do not know how to configure the parameters shown in the menu.
The default settings are shown below.
Item
Setting
DHCP
Disable
IP ADDRESS
192.168.2.1
SUBNET MASK
255.255.255.0
DEFAULT GATEWAY
192.168.2.1
DNS Addr.
192.168.2.1
Information
This read-only menu provides information on the active sources and the latest firmware version
50
5. Maintenance and Troubleshooting
Maintenance
The AVOCOR Series LED Displays does not require any routine maintenance other than occasional cleaning
with a non-abrasive cloth. There are no user-serviceable or replaceable parts. Unless you are a qualified,
factory-trained technician, do not attempt to repair or replace any system component yourself. You will void
the product warranty if you do so.
Troubleshooting
Table 5-1 provides some general guidelines for troubleshooting problems you may encounter with the
AVOCOR Series LED Display. If the suggested solutions fail to resolve the problem or if you encounter an issue
not described here, please contact your dealer.
Table 5-1. Troubleshooting Chart
Symptom
The display does not turn on.
The display is on and menus
appear, but there is no picture.
The remote control does not
work.
Image geometry is incorrect.
Possible Cause(s)
Solution
The display is not plugged in or the
AC outlet is not active.
Ensure that the display is plugged
in and that the AC outlet is active.
The main power switch is off.
Set the main power switch (see
Figure 2-1) to the on position.
The remote control batteries have
run out.
Replace the batteries.
Incorrect source selection.
Select the correct source.
Source component is not turned on.
Turn on the source component.
Source component is connected
incorrectly or not at all.
Check connections from the
source component to the display.
The remote control batteries have
run out.
Replace the batteries.
The buttons are locked.
Unlock the buttons by pressing
ENTER, ENTER, EXIT, EXIT, ENTER and
EXIT, in sequence.
Incorrect aspect ratio selection.
Select a different aspect ratio.
51
Table 5-1. Troubleshooting Chart (continued)
Symptom
The display is jittery or unstable.
Possible Cause(s)
Solution
Poor-quality or improperly
connected source.
Ensure that the source is properly
connected and of adequate
quality for detection.
The horizontal or vertical scan
frequency of the input signal may
be out of range for the display.
Correct at the source.
Image is too bright and / or lacks
definition in the bright areas of
the image.
Contrast is set too high.
Decrease the contrast setting.
Image appears “washed out”
and / or dark areas appear
too bright.
Brightness is set too high.
Decrease the brightness setting.
Image is too dark.
Brightness and / or Backlight are set
too low.
Increase the brightness and / or
backlight settings.
Images from an HDMI source do
not display.
The resolution and frequency of the
video card in the computer are not
compatible with the display.
Select a compatible resolution and
vertical frequency (refer to
Supported Timings on page 69).
HDMI cable from source to display is
either defective or too long.
Try a known-good and / or shorter
HDMI cable.
The resolution and frequency of the
video card in the computer are not
compatible with the display
Select a compatible resolution and
vertical frequency (refer to
Supported Timings on page 69).
Clock and Phase settings need
adjustment.
Adjust Clocks and Phase settings
(refer to Setup Settings page 46).
Multi-touch controller host computer
is not connected correctly.
See Figure 3-7.
Host computer hardware or OS
incompatibility.
Refer to Enabling the Touch Screen
on page 34.
Computer images do not
display correctly.
Touch screen doesn’t work.
52
Should you require assistance with a suspected hardware fault, please contact the support line below. You
will require your unit serial number. The operator will attempt to diagnose any fault and will take action as
appropriate.
US Warranty Support
Tel. 858-266-8363
Email.
[email protected]
53
6. External Control
In addition to using the display keypad or remote control unit, you can control the display using a serial (RS232) link to send ASCII commands and receive responses to those commands.
You also use discrete infrared (IR) control codes to program a third-party remote control unit. For more
information, refer to Using Discrete IR Codes on page 64.
Serial Communications
The display uses a simple text-based control protocol to take requests from control devices and to provide
responses to such devices. This section describes how to send control messages over a serial link between the
display and an automation/control system or a PC running a terminal emulation program such as Windows&reg;
HyperTerminal or Tera Term.
RS-232 Connection and Port Configuration
Connect your control system or PC to the RS-232 input of the display as shown in Figure 3-2.
Configure the RS-232 controller or PC serial port as follows: no parity, 8 data bits, 1 stop bit and no flow
control. Set the baud rate to 115200, to match that of the display RS-232 port.
Command and Response Format
Commands sent from an automation/control system or PC to the display must have the following format:
[STX] [IDT] [TYPE] [CMD] ([VALUE] or [REPLY]) [ETX] [CR]
Where:

[STX] indicates the start of the command data (always 07).

[IDT] is the display ID (always 01).

[TYPE] is the command type:
00 = return to host (response from the LCD panel)
01 = read / action
02 = write

[VALUE] is the parameter setting for the command.

[REPLY] is the parameter setting for the command, acknowledged by the display in its response to a
command.

[ETX] indicates the end of the command data (always 08).

[CR] is the ASCII carriage return key (0x0D).
54
Command and Response Examples
Here are some examples of serial commands and their responses:
Table 6-1. Serial Command/ Response Examples
Description
Command sent to LCD Panel
Response Received from LCD Panel
Turn LCD panel power off.
07 01 02 50 4F 57 00 08
07 01 00 50 4F 57 00 08
Turn LCD panel power on.
07 01 02 50 4F 57 01 08
07 01 00 50 4F 57 01 08
Request LCD panel power status.
07 01 01 50 4F 57 08
07 01 00 50 4F 57 XX 08
(XX = 0 when off or 1 when on)
Set the LCD panel contrast to 30
(1E hex).
07 01 02 43 4F 4E 1E 08
07 01 00 43 4F 4E 1E 08
Reset the LCD panel display
settings.
07 01 02 41 4C 4C 00 08
07 01 00 41 4C 4C 00 08
Request LCD panel serial number.
07 01 01 53 45 52 08
07 01 00 53 45 52 S(0)…S(12) 08
S(0) …S(12) = the serial number in ASCII
Request LCD panel firmware
version.
07 01 01 47 56 45 08
07 01 00 47 56 45 S(0)…S(5) 08
S(0)…S(5) = the firmware version in ASCII
Serial Command List
Table 6-2 lists all supported commands.
Table 6-2. Serial Commands
Main Item
Control Item
CMD
Type
Power Control
POW
W/R
IPC Control
IPC
W/R
Power Control and
Input Source
Input Source
MIN
BRI
Display
Adjustment
Display
Adjustment
W/R
W/R
Value
(DEC)
Reply
(DEC)
00
00
Off (soft power)
01
01
On (soft power)
00
00
Off
01
01
On
00
00
VGA
09
09
HDMI 1
10
10
HDMI 2
11
11
HDMI 3
12
12
HDMI 4
13
13
Displayport
14
14
IPC/OPS
17
17
HDMI 5 (Front Panel)
18
18
Media Player
(Win/Android)
0~100
0~100
Back Light Brightness
42 52 49
0~100
0~100
Digital Brightness
Level
42 52 4C
00
00
Off (Back Light)
01
01
On (Back Light)
Content
CMD
(HEX)
50 4F 57
49 50 43
4D 49 4E
BRL
W/R
BLC
W/R
CON
W/R
0~100
0~100
Contrast
43 4F 4E
HUE
W/R
0~100
0~100
Hue
48 55 45
42 4C 43
55
Main Item
Control Item
CMD
SAT
NOR
MEM
Display
Adjustment
Display
Adjustment
Sharpness
PIP Adjust
W/R
W/R
W/R
Reply
(DEC)
Content
0~100
0~100
Saturation
00
00
Noise Reduction: Off
01
01
Noise Reduction:
Low
02
02
Noise Reduction:
Medium
03
03
Noise Reduction:
High
00
00
MEMC: Off
01
01
MEMC: Low
02
02
MEMC: Medium
03
03
MEMC: High
CMD
(HEX)
53 41 54
4E 4F 52
4D 45 4D
(AVF-6510
only)
W/R
0~100
0~100
Red Gain (mapping
0~100)
55 53 52
USG
W/R
0~100
0~100
Green Gain
(mapping 0~100)
55 53 47
USB
W/R
0~100
0~100
Blue Gain (mapping
0~100)
55 53 42
UOR
W/R
0~100
0~100
Red Offset (mapping
0~100)
55 4F 52
UOG
W/R
0~100
0~100
Green Offset
(mapping 0~100)
55 4F 47
UOB
W/R
0~100
0~100
Blue Offset
(mapping 0~100)
55 4F 42
00
00
User
01
01
6500K
02
02
9300K
06
06
5000K
07
07
7500K
00
00
Gamma Off
01
01
Gamma 2.2
W/R
43 4F 54
GAC
W/R
PHA
W/R
0~100
0~100
Phase
50 48 41
CLO
W/R
0~100
0~100
Clock
43 4C 4F
HOR
R/W
0~100
0~100
Horizontal Position
48 4F 52
VER
R/W
0~100
0~100
Vertical Position
56 45 52
ADJ
W
00
00
Auto Adjust
41 44 4A
SHA
W/R
0~100
0~100
Sharpness
53 48 41
00
00
PIP OFF
01
01
PIP Small
02
02
PIP medium
03
03
PIP large
04
04
PbP (Side By Side)
05
05
PbP Portrait
06
06
3 Windows
07
07
4 Windows
00
00
VGA
09
09
HDMI 1
10
10
HDMI 2
11
11
HDMI 3
PSC
W/R
Other Control
PIP Source
Selection
Value
(DEC)
USR
COT
VGA
Adjustment
Type
PIN
W/R
47 41 43
50 53 43
50 49 4E
56
Main Item
Control Item
CMD
PIN
Type
PIP
PIP position
PIP/Main Swap
Other Control
PPO
SWA
ASP
ZOM
Baudrate
Adjustment
Other Control
BRA
RCU
Content
CMD
(HEX)
12
HDMI 4
13
13
DisplayPort
14
14
IPC/OPS
17
17
HDMI 5 (Front
Panel)
18
18
Media Player
(Win/Android)
W/R
(refer to
PIN)
(refer
to PIN)
Select the input
source of sub
window 2 (refer to
PIN)
50 49 4F
W/R
(refer to
PIN)
(refer
to PIN)
Select the input
source of sub
window 3 (refer to
PIN)
50 49 50
00
00
PIP Position Bottomleft
01
01
PIP Position BottomRight
02
02
PIP Position Top-left
03
03
PIP Position Topright
00
00
Swap main and PIP
00
00
Native
01
01
Full Screen
02
02
Pillarbox/4:3
03
03
Letterbox
01
01
Full Screen
02
02
Pillarbox/4:3
03
03
Letterbox
0~10
0~10
Adjust overscan
ratio
00
00
115200
01
01
38400
02
02
19200
03
03
9600
00
00
MENU Key
02
02
UP Key
03
03
DOWN Key
04
04
LEFT Key
05
05
RIGHT Key
06
06
ENTER Key
07
07
EXIT Key
18
18
SOURCE Key
23
23
SCALING Key
W/R
W/R
W
W/R
Scaling
PAS
Reply
(DEC)
12
PIP Source
Selection
PIO
Value
(DEC)
W/R
W/R
W/R
W
50 49 4E
50 50 4F
53 57 41
41 53 50
50 41 53
5A 4F 4D
42 52 41
52 43 55
57
Main Item
Control Item
CMD
RCU
Other Control
Other Control
Type
W
Value
(DEC)
Reply
(DEC)
Content
24
24
FREEZE Key
25
25
MUTE Key
28
28
AUTO Key
29
29
VOLUME+ Key
30
30
VOLUME- Key
43
43
Blank screen
44
44
MediaPlayer / Win10
160
160
Avocor LowBlue
Bright- Key
161
161
Avocor LowBlue
Bright+ Key
00
00
Reset all
00
00
Un-lock keys
01
01
Lock keys
CMD
(HEX)
52 43 55
ALL
W
KLC
W/R
SER
R
13
bytes
Read Serial Number
53 45 52
MNA
R
13
bytes
Read Model Name
4D 4E 41
GVE
R
6 bytes
Read Firmware
Version
47 56 45
RTV
R
Curren
t value
Read RS232 table
Version
52 54 56
00
[00]+5
byte
Querying main
scaler version
01
[00]+5
byte
Querying sub mcu
version
02
[00]+5
byte
Querying network
module version
GVS
W
41 4C 4C
4B 4C 43
47 56 53
VOL
W/R
0~100
0~100
volume
56 4F 4C
BAS
W/R
0~12
0~12
Bass(-6~6)
42 41 53
TRE
W/R
0~12
0~12
Treble(-6~6)
54 52 45
BAL
W/R
0~12
0~12
Bass(-6~6)
42 41 4C
00
00
01
01
02
02
Current audio
source: HDMI2
03
03
Current audio
source: HDMI3
04
04
Current audio
source: HDMI4
05
05
Current audio
source: Displayport1
07
07
Current audio
source: OPS
08
08
Current audio
source: Front HDMI
09
09
Current audio
source: Win10
Audio
CAS
W/R
Current audio
source: Analog
Current audio
source: HDMI1
43 41 53
58
Main Item
Control Item
CMD
Type
INS
W/R
MUT
W/R
Audio
Scheme
Selection
EcoMode
Other Control
SCM
WFS
W/R
W/R
Value
(DEC)
Reply
(DEC)
Content
00
00
Internal Speaker Off
01
01
Internal Speaker On
00
00
Mute Off
01
01
Mute On
00
00
User
01
01
Sport
02
02
Game
03
03
Cinema
04
04
Vivid
0
0
Set VGA_ONLY
1
1
Set
VGA_DIGITAL_RS232
2
2
Set Never_Sleep
CMD
(HEX)
49 4E 53
4D 55 54
53 43 4D
57 46 53
RTY
W/R
0~99
0~99
Set Real Time Year
52 54 59
RTM
W/R
1~12
1~12
Set Real Time Month
52 54 4D
RTD
W/R
1~31
1~31
Set Real time Day
52 54 44
RTH
W/R
0~23
0~23
Set Real Time Hour
52 54 48
RTN
W/R
0~59
0~59
Set Real Time Minute
52 54 4E
0
0
Same Settings On All
1
1
Same Settings On
Work Days
2
2
User
1
1
Sunday Alarm
Enable
2
2
Monday Alarm
Enable
4
4
Tuesday Alarm
Enable
8
8
Wednesday Alarm
Enable
16
16
Thursday Alarm
Enable
32
32
Friday Alarm Enable
64
64
Saturday Alarm
Enable
1
1
Sunday Alarm
Disable
2
2
Monday Alarm
Disable
4
4
Tuesday Alarm
Disable
TMS
W/R
RTC
AEN
AEF
W/R
W/R
54 4D 53
41 45 4E
41 45 46
59
Main Item
Control Item
CMD
AEF
Other Control
RTC
Type
W/R
Value
(DEC)
Reply
(DEC)
Content
8
8
Wednesday Alarm
Disable
16
16
Thursday Alarm
Disable
32
32
Friday Alarm Disable
64
64
Saturday Alarm
Disable
CMD
(HEX)
41 45 46
NNH
W/R
0~23
0~23
Monday On Hour
4E 4E 48
NNM
W/R
0~59
0~59
Monday On Minute
4E 4E 4D
NFH
W/R
0~23
0~23
Monday Off Hour
4E 46 48
NFM
W/R
0~59
0~59
Monday Off Minute
4E 46 4D
ENH
W/R
0~23
0~23
Tuesday On Hour
45 4E 48
ENM
W/R
0~59
0~59
Tuesday On Minute
45 4E 4D
EFH
W/R
0~23
0~23
Tuesday Off Hour
45 46 48
EFM
W/R
0~59
0~59
Tuesday Off Minute
45 46 4D
DNH
W/R
0~23
0~23
Wednesday On
Hour
44 4E 48
DNM
W/R
0~59
0~59
Wednesday On
Minute
44 4E 4D
DFH
W/R
0~23
0~23
Wednesday Off
Hour
44 46 48
DFM
W/R
0~59
0~59
Wednesday Off
Minute
44 46 4D
UNH
W/R
0~23
0~23
Thursday On Hour
55 4E 48
UNM
W/R
0~59
0~59
Thursday On Minute
55 4E 4D
UFH
W/R
0~23
0~23
Thursday Off Hour
55 46 48
UFM
W/R
0~59
0~59
Thursday Off Minute
55 46 4D
INH
W/R
0~23
0~23
Friday On Hour
INH
INM
W/R
0~59
0~59
Friday On Minute
INM
IFH
W/R
0~23
0~23
Friday Off Hour
IFH
IFM
W/R
0~59
0~59
Friday Off Minute
IFM
TNH
W/R
0~23
0~23
Saturday On Hour
TNH
TNM
W/R
0~59
0~59
Saturday On Minute
TNM
TFH
W/R
0~23
0~23
Saturday Off Hour
TFH
TFM
W/R
0~59
0~59
Saturday Off Minute
TFM
SNH
W/R
0~23
00~17
0~23
00~17
SNM
W/R
0~59
00~3B
0~59
00~3B
SFH
W/R
0~23
00~17
0~23
00~17
SFM
W/R
0~59
00~3B
0~59
00~3B
60
Main Item
Control Item
Auto Scan
IRFM
Other Control
ATS
IRF
Type
W/R
W/R
Smart Light
Control
SLC
Power LED
LED
W/R
DisplayPort
Mode
DPM
W/R
DisplayPort
EDID
EDP
W/R
HDMI RGB
Color Range
Touch Control
Win10 Player
CMD
Win10 Power
Control
HCR
TOC
WPC
W/R
W/R
W/R
Value
(DEC)
Reply
(DEC)
Content
0
0
Off
1
1
Main
2
2
Multi
3
3
All
0
0
Off
1
1
On
0
0
Off
1
1
DCR
2
2
Light Sensor
0
0
Off
1
1
On
0
0
DP 1.1
1
1
DP 1.2
00
00
4Kx2K
01
01
1080P
00
00
Auto Detect
01
01
Full Range
02
02
Limited Range
00
00
Auto (Read Only)
01
01
OPS
02
02
External
(Touch1 / Front USB)
02
02
External Touch 2
03
03
External touch 2
(Rear USB)
04
04
00
00
01
01
02
02
03
03
W/R
04
04
Win10
Read: 0 – Win PC
Power is Off
Read: 1 - Win PC
Power is On
Write: 0 - Release
WinPC power
button
Write: 1- Press Win
PC Power button
untill receives
release command
Write: 2 - Press Win
PC Power button for
1 second
Write: 3 - Press Win
PC Power button for
4 seconds
Write: 4 - If Win PC is
On, force shutdown
Win PC (Press Win
PC power button till
WinPC is off).
CMD
(HEX)
41 54 53
49 52 46
53 4C 43
4C 45 44
44 50 4D
45 44 50
48 43 52
54 4F 43
57 50 43
61
Main Item
OSD Control
Control Item
CMD
Type
Value
(DEC)
Reply
(DEC)
Content
CMD
(HEX)
Transpare-ncy
OST
W/R
0~4
0~4
OSD Transparency
4F 53 54
H Position
OSH
W/R
0~100
0~100
OSD H Position
4F 53 48
V Position
OSV
W/R
0~100
0~100
OSD V Position
4F 53 56
00
00
English
01
01
French
02
02
German
03
03
Dutch
04
04
Hungarian
05
05
Slovene
06
06
Serbian
07
07
Croatian
08
08
Danish
5~60
5~60
OSD Timeout (5, 10,
20, 30, 60 sec)
0
0
Off
1
1
On
0
0
No
1
1
Yes
0
0
Disable
1
1
Enable
0
0
Load network
default settings (It
will take about 15
seconds.)
0
0
Off (Power Status
Alert)
1
1
On (Power Status
Alert)
0
0
Off (Source Status
Alert)
1
1
On (Source Status
Alert)
0
0
Off (Signal Lost Alert)
1
1
On (Signal Lost Alert)
OSD
Language
OSL
W/R
OSD Timeout
OSO
W/R
Splash Screen
SPS
W/R
Network
Enable
NWE
W/R
Dynamic IP
DIP
W/R
Default
LDS
PSA
E-Mail Alert
SSA
W
W/R
W/R
Ethernet Setup
Static IP
Settings
4F 53 4C
4F 53 4F
53 50 53
4E 57 45
44 49 50
4C 44 53
50 53 41
53 53 41
SLA
W/R
53 4C 41
IP1
W/R
0~255
0~255
Static IP Address 1
49 50 31
IP2
W/R
0~255
0~255
Static IP Address 2
49 50 32
IP3
W/R
0~255
0~255
Static IP Address 3
49 50 33
IP4
W/R
0~255
0~255
Static IP Address 4
49 50 34
MK1
W/R
0~255
0~255
Subnet Mask 1
4D 4B 31
MK2
W/R
0~255
0~255
Subnet Mask 2
4D 4B 32
MK3
W/R
0~255
0~255
Subnet Mask 3
4D 4B 33
MK4
W/R
0~255
0~255
Subnet Mask 4
4D 4B 34
GW1
W/R
0~255
0~255
Gateway 1
47 57 31
62
Main Item
Ethernet Setup
Control Item
Static IP Settings
CMD
Type
Value
(DEC)
Reply
(DEC)
Content
CMD
(HEX)
GW2
W/R
0~255
0~255
Gateway 2
47 57 32
GW3
W/R
0~255
0~255
Gateway 3
47 57 33
GW4
W/R
0~255
0~255
Gateway 4
47 57 34
FD1
W/R
0~255
0~255
DNS Address 1
46 44 31
FD2
W/R
0~255
0~255
DNS Address 2
46 44 32
FD3
W/R
0~255
0~255
DNS Address 3
46 44 33
FD4
W/R
0~255
0~255
DNS Address 4
46 44 34
SNS
W
0
0
Save Network
Settings
53 4E 53
MAC
W
0~5
0~255
Querying MAC ID
#0~#5
4D 41 43
63
Using Discrete IR Codes
The display accepts commands in the form of infrared (IR) signals that conform to the NEC protocol. Each
display remote control button has an IR control code associated with it.
You can use these codes to program a third-party, “universal” remote control unit to work with the display.
These third-party products usually come with a computer software application for this purpose. For more
information, consult the documentation provided with the remote control unit.
IR Command Protocol
The IR control codes have the following characteristics:

Each code consists of the following:
- A leader pulse (a modulated pulse of 9 ms followed by a non-modulated pulse of 4.5 ms);
- 16 address bits (also called a “custom code”): eight (8) bits for the address followed by the logical
inverse of the address. The custom code for the display is 16559 decimal (0x40AF, binary 01000000
10101111);
- 16 data bits: eight (8) bits for the command followed by the logical inverse of the command;
- An end pulse (a modulated pulse of 0.56 ms, similar to the modulated pulse in the ‘0’ and ‘1’ bits). The
end of the modulated pulse constitutes the end of the data transmission.

The carrier frequency is 38 kHz, with the modulated pulses having a 33% duty cycle.

Commands are sent at a maximum rate of 9 Hz.
For example, here is the NEC control code for the POWER button on the display remote control unit:
Hex
40
AF
1C
E3
Binary
01000000
10101111
00011100
11100011
Function
Cust. Code Byte 1
Cust. Code Byte 2
Command
Command
(Logical Inverse)
64
IR Control Code List
Table 6-3 lists the IR control codes for the display.
Table 6-3. Infrared (IR) Control Codes
NO
Customer Code
Data Code
Function
1
40AF
04FB
----------
2
40AF
1CE3
POWER
3
40AF
07F8
SOURCE
4
40AF
08F7
----------
5
40AF
09F6
WIN PC
6
40AF
0AF5
BLANK
7
40AF
0BF4
----------
8
40AF
0CF3
FREEZE
9
40AF
1AE5
----------
10
40AF
15EA
MUTE
11
40AF
10EF
----------
12
40AF
11EE
VOLUME -
13
40AF
0DF2
----------
14
40AF
16E9
VOLUME +
15
40AF
06F9
BRIGHTNESS SETTINGS -
16
40AF
13EC
BRIGHTNESS SETTINGS +
17
40AF
02FD
UP
18
40AF
01FE
LEFT
19
40AF
0EF1
MENU
20
40AF
03FC
RIGHT
21
40AF
19E6
DOWN
22
40AF
12ED
ENTER
23
40AF
05FA
EXIT
24
40AF
40BF
----------
25
40AF
41BE
----------
26
40AF
14EB
AUTO
27
40AF
43BC
----------
28
40AF
00FF
SCALING
29
40AF
17E8
----------
30
40AF
18E7
----------
31
40AF
1EE1
----------
32
40AF
0FF0
----------
33
40AF
1BE4
----------
34
40AF
1DE2
----------
35
40AF
1FE0
----------
36
40AF
42BD
----------
65
Notes:
66
7. Specifications
Table 7-1 lists the signal types supported by each input on the display.
AVF-7510
PANEL
Diagonal Size (Inch)
Backlight
Aspect Ratio
Input Resolution
Response Time
Brightness
Contrast Ratio
75”
Edge LED
16:9
3840 x 2160 @ 60 Hz
8 (ms)
410 (cd/m2)
1200:1
Viewing Angle
178&ordm; (H) / 178&ordm; (V)
Supported Colours
1.07 Billion colours
Display Orientation
Landscape compatible
TOUCH SYSTEM
Interface
Touch USB
Touch
High-resolution inGlass™ touch; Up to 10 points
Glass
AGC glass; 0.1-inch thickness
Supported Operating System
Windows 7 / 8 / 10; Mac OS 10
AUDIO
Built-in Speakers
4 KΩ / 2 x 10W
CONNECTIVITY
Connections
5 x HDMI / 1 x VGA / 1 x DisplayPort
Audio
Audio Out / PC Audio In / SPDIF Out
Control
2 x Touch USB / RS232 / Ethernet
WIN PC Note
CPU
Intel Atom Quad Core Processor
Memory
2GB DDR3
Storage
32GB (eMMC)
Ethernet
10/100 Mbps (RJ-45)
WiFi
Bluetooth
USB 2.0/3.0
OS
802.11 b/g/n, 2.4GHz, 1T1R, Realtek RTL8723BS Module
4.0
x2 / x1 (Type A)
Windows 10 Home Edition (x64)
PHYSICAL SPECIFICATIONS
Dimensions
Weight
Wall Mount (VESA)
Fanless Design
67.7 x 41.2 x 3.7 (in)
Net: 87 kg / Gross: 95 kg
23.6 x 15.7 (in)
23.6 x 23.6 (in)
Yes
67
OSD FUNCTIONS
OSD Languages
Source Auto Detect Function
English, German, Dutch, French, Danish, Slovenian, Hungarian, Serbian,
Croatian
Yes
POWER
Power Supply
AC100-240V (Worldwide), Max 3.5 A, 50/60Hz
Maximum Power
Consumption
320 W
Standby
≦0.5 W
ENVIRONMENTAL
Operating Temperature
Storage Temperature
Humidity
NOTE
5 &deg;C ~ 40 &deg;C
-20 &deg;C ~ 60 &deg;C
35% ~ 85%
When the display is powered up for the first time, turning on the WIN PC will take 12~20
seconds to initiate.
68
Supported Timings
Table 7-2 lists the signal types supported by each input on the display.
Table 7-2. Supported Timings By Input
Timing
VGA 640x480
SVGA 800x600
XGA 1024x768
WXGA1366x768
1280 x 720
VESA
1280 x 768
1280 x 800
1152x864
SXGA
1280x1024
1440 x 900
WSXGA+ 1680 x1050
Dot clock
(MHz)
HDMI
VGA
DisplayPort
31.469
59.94
25.175
O
O
O
37.861
72.809
31.5
O
O
O
37.5
75
31.5
O
O
O
43.269
85.008
36
O
O
O
35.156
56.25
36
O
O
O
37.879
60.317
40
O
O
O
48.077
72.188
50
O
O
O
46.875
75
49.5
O
O
O
53.674
85.06
56.25
O
O
O
48.363
60.004
65
O
O
O
56.476
70.069
75
O
O
O
60.023
75.029
78.75
O
O
O
68.677
84.997
94.5
O
O
O
47.712
59.79
85.5
O
O
O
44.444
59.98
64
-
O
O
44.772
59.86
74.5
-
O
O
56.456
74.78
95.75
-
O
O
47.776
59.87
79.5
-
O
O
47.396
59.995
68.25
-
O
O
68.633
84.837
117.5
-
O
O
49.306
59.91
71
O
O
O
49.702
59.81
83
O
O
O
67.5
75
108
O
O
O
63.981
60.02
108
O
O
O
79.976
75.025
135
O
O
O
91.146
85.024
157.5
-
O
O
55.469
59.901
88.75
-
-
O
55.935
59.88
106.5
O
O
O
64.674
59.883
119
O
O
O
65.29
59.954
146.25
O
O
O
75
60
162
O
O
O
1920 x 1080
66.587
59.93
138.5
-
O
O
WUXA 1920 x 1200
74.038
59.95
154
-
O
O
88.787
59.951
241.5
O
-
O
89.521
59.961
312.25
-
-
O
98.713
59.972
268.5
O
-
O
QSXGA 2560x1600
HDTV
fV (Hz)
UXGA 1600 x 1200
QHD 2560x1440
EDTV
fH (kHz)
99.458
59.987
348.5
-
-
O
480p
31.5
60
27.03
O
-
O
576p
31.25
50
27
O
-
O
720p
37.5
50
74.25
O
-
O
1280x720
44.995
59.94
74.176
O
-
O
45
60
74.25
O
-
O
69
Timing
fV (Hz)
Dot clock
(MHz)
HDMI
VGA
DisplayPort
1080i
28.13
50
74.25
O
-
O
1920x1080
33.716
59.94
74.176
O
-
O
33.75
60
74.25
O
-
O
27
24
74.25
O
-
O
28.125
25
74.25
O
-
O
33.75
30
74.25
O
-
O
56.25
50
148.5
O
-
O
67.433
59.94
148.352
O
-
O
67.5
60
148.5
O
O
O
54
24
297
O
-
O
1080p 1920x1080
4K2K
fH (kHz)
3840x2160
56.25
25
297
O
-
O
67.5
30
297
O
-
O
110.5
49.977
442
-
-
O
112.5
50
594
-
-
O
133.313
59.997
533.25
-
-
O
135
60
594
-
-
O
70
Overall Dimensions
Figure 7-1 shows the display dimensions of AVF-7510 (all dimensions are in inches).
Figure 7-1. AVF-7510 Display Dimensions
71
Notes:
72
Appendix I: Moving and Carrying Notice
Moving the Display:
Moving the display requires at least two people. Attempting to move the display with one person may result in
dropping the display and/or serious injury. When moving a display in its shipping carton, lift the carton using
the white handles.
Carrying the display:
This display is heavy; please follow proper lifting technique, as pictured below. Failure to do so may cause
injury.
AVOID
OK
73
Appendix II: Installing a Wall Mount
Before installing, please make sure the wall is strong enough to hold the necessary weight of the display and
the mount.
Step1. Keep the display facing the ground and place it on a flat object.
Step2. Remove the screws (M8*15) from the back of the display.
Step3. Align the wall brackets with the mounting holes and attach the brackets to the display using the screws
removed in Step 2.
Caution: Longer screws will damage the display.
Use maximum 15mm/0.59” long screws.
0.3” Metric
74
Appendix III: Installing an OPS Module
Follow the steps below to install an OPS module.
Step1. Use a screw driver to unscrew the OPS slot cover on the display input panel.
Do not lose the screws that are removed.
Step2. Install the OPS module by sliding it into the .OPS slot until you hear a click, indicating the module is
securely inserted.
Step3. Secure the OPS module in position by screwing it onto the display input panel using the screws that are
removed earlier.
75
Appendix IV: Wall Mount Safety Notes
76
77
Appendix V: Power/ PC Key Operations
When current input is WIN PC:

When Win10 PC Power Mode is set to Auto or
Manual, pressing the button once will turn on
Win10 PC.
When current input is NOT WIN PC:

When Win10 PC Power Mode is set to Auto or
Manual, pressing the button once will switch
the input souce to Win10 PC and turn on Win10
PC.

When Win10 PC Power Mode is set to Off and
Win10 PC is turned off, pressing the button
once will switch the input source to OPS.

When Win10 PC is on, pressing the button once
will turn off Win10 PC.

When Win10 PC Power Mode is set to Off and
Win10 PC is turned Off, pressing the button
once will switch the input source to OPS.

Press the button to turn on/off the display.

When Win10 PC Power Mode is set to Auto, pressing the button will turn on the display and Win10 PC.

When Win10 PC is running and Win10 PC Power Mode is set to Auto or Manual, pressing the botton will
turn off the screen and Win10 PC will remain running in the background.
1.
Operation of the power/PC keys will not conform to the description above if you have made changes
to the default Power/Sleep settings in the windows PC.
2.
Please avoid unplugging the AC power cord while Win10 PC is still on. To check the status of Win10 PC,
you may check the floating message box on screen, or use the remote control to enter the OSD menu
and find the information in the Information menu page.
NOTE
78
Appendix VI: Ethernet Remote Control Settings
The device can be configured by opening a browser and connecting to web server directly.
Use the browser to configure the demo board. Connect the browswer to the IP address of NET2UART module,
and the Login window will pop up as follows.
Default IP
192.168.2.1
Default ID
admin
Default Password
system
Configurations
Administrator
Authentication Configuration
79
System IP Configuration
Network Status
Load Default Setting
80
Firmware Update
Boot Loader Upgrade
81
TCP Mode
Telnet Server/Client
Set the device to be a Telnet Server or Client.
Port Number
When in Server mode, assign the port number used to connect remotely. When in Client mode, assign the port
number for the device to connect to the remote site.
Remote Server IP Address
When in Client mode, the device will connect to the remote server with the IP address set here.
Client mode inactive timeout
When NET2UAR is operating in TCP client mode, it will always try to connect with the remote server. The time
configured here is for NET2UART to rebuild connection after timeout.
Server mode protect timeout
When NET2UART is operating in TCP server mode, it would protect the TCP connection from getting replaced
in the period of the time set here.
82
UDP Mode
Status
When TCP mode is set as Server mode or Client mode, the UDP mode would be disabled automatically, and
vice versa.
Local Port
Assign the port number here to allow the device to open for the remote site to send data via UDP. The IP
address of the remote site must be set in the Remote Address table, or NET2UART will ignore its data.
Remote Address
The Remote Address table allows 10 entries of remote site IP addresses and ports. When NET2UART is sending
data to network, the data will be sent to the each remote IP address entered in the table simultaneously. The
port number is the remote site port number that NET2UART will send data to via UDP.
If the port number is set as “0”, the NET2UART will use the port number that the remote site sends data from as
the destination port number, or use the local port number as the destination port number if the remote site
has not sent data to NET2UART.
83
UART
Mode
Select the UART interface.
Baud rate
Select the baud rate of UART interface.
Character Bits
Select the number of character bits of UART interface.
Parity Type
Select the parity type of UART interface.
Stop Bit
Select the stop bit type of UART interface.
Hardware Flow Control
Select the flow control type of UART interface. The hardware flow control will use CTS/RTS for the control
signals.
Uart Memory Overflow count
Shows the number of overflow bytes in network buffer.
Uart FIFO Overflow count
Shows the number of overflow times in UART RX buffer.
84
Delimiter

Character 1 &amp; 2:
Set Character 1 and/or Character 2 to be the delimiter.
Once the delimiter is active, NET2UART would monitor all data received from UART. All data received
from UART will be stored in NET2UART internal buffer first, and will only be sent to Ethernet once the
delimiter is detected. If the delimiters have not been detected and the internal buffer of NET2UART is
stuffed, the incoming data will overwrite the previous data stored in NET2UART.

Drop Character:
The Drop Character is set to drop delimiter or not. If Drop Character is active, the delimiter received from
UART will not be sent out to Ethernet.

Silent time:
Once the Silent time is active, NET2UART will keep all data received from UART in its internal buffer and
check the time period of no data received from UART. It will then send out the internal data once the
time is out.
SMTP
85
Reset Device
Reset NET2UART module.
86
">

Hello! I am an AI chatbot specifically trained to assist you with the AVOCOR VTF-7510 User manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!