Central Pneumatic 65940 Operating instructions

PISTOL GRIP
AIR SCREWDRIVER
65940
SET UP AND OPERATING INSTRUCTIONS
Distributed exclusively by Harbor Freight Tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
`
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright© 2008 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Manual Revised 11h
SAVE THIS MANUAL
NOTICE is used to
address practices
not related to personal injury.
Keep this manual for the safety
warnings and precautions, assembly,
operating, inspection, maintenance and
cleaning procedures. Write the product’s
serial number in the back of the manual
near the assembly diagram (or month
and year of purchase if product has no
number). Keep this manual and the
receipt in a safe and dry place for future
reference.
Safety Alert Symbol and Signal
Words
In this manual, on the labeling,
and all other information
provided with this product:
This is the safety alert
symbol. It is used to alert
you to potential personal
injury hazards. Obey all
safety messages that
follow this symbol to avoid
possible injury or death.
DANGER indicates
a hazardous
situation which, if not
avoided, will result in death or
serious injury.
CAUTION, without
the safety alert
symbol, is used to address
practices not related to
personal injury.
IMPORTANT SAFETY
INSTRUCTIONS
INSTRUCTIONS PERTAINING
TO A RISK OF FIRE,
ELECTRIC SHOCK, OR
INJURY TO PERSONS
WARNING – When using tools, basic
precautions should always be
followed, including the following:
General
a.
WARNING
indicates a
hazardous situation which, if
not avoided, could result in
death or serious injury.
CAUTION, used
with the safety
alert symbol, indicates a
hazardous situation which, if
not avoided, could result in
minor or moderate injury.
Work area
a.
Keep the work area clean and well
lighted. Cluttered benches and dark
areas increase the risks of electric
shock, fire, and injury to persons.
b.
Do not operate the tool in
explosive atmospheres, such as in
the presence of flammable liquids,
gases, or dust. The tool is able to
create sparks resulting in the ignition
of the dust or fumes.
c.
Keep bystanders, children, and
visitors away while operating the
SKU 65940
To reduce the risks of electric
shock, fire, and injury to persons,
read all the instructions before
using the tool.
For technical questions, please call 1-800-444-3353.
Page 2
tool. Distractions are able to result in
the loss of control of the tool.
Personal safety
a.
b.
c.
d.
e.
Stay alert. Watch what you are
doing and use common sense
when operating the tool. Do not
use the tool while tired or under
the influence of drugs, alcohol, or
medication. A moment of inattention
while operating the tool increases the
risk of injury to persons.
Dress properly. Do not wear loose
clothing or jewelry. Contain long
hair. Keep hair, clothing, and
gloves away from moving parts.
Loose clothes, jewelry, or long hair
increases the risk of injury to persons
as a result of being caught in moving
parts.
Avoid unintentional starting.
Be sure the switch is off before
connecting to the air supply. Do not
carry the tool with your finger on the
switch or connect the tool to the air
supply with the switch on.
Remove adjusting keys and
wrenches before turning the tool
on. A wrench or a key that is left
attached to a rotating part of the tool
increases the risk of personal injury.
Do not overreach. Keep proper
footing and balance at all times.
Proper footing and balance
enables better control of the tool in
unexpected situations.
f.
SKU 65940
Use safety equipment. A
dust mask, non-skid safety
shoes and a hard hat must
be used for the applicable
conditions. Wear heavy-duty work
gloves during use.
g.
Always wear eye
protection. Wear ANSIapproved safety goggles.
h.
Always wear hearing
protection when using
the tool. Prolonged
exposure to high intensity
noise is able to cause hearing loss.
Tool use and care
a.
Use clamps or another practical
way to secure and support the
workpiece to a stable platform.
Holding the work by hand or against
the body is unstable and is able to
lead to loss of control.
b.
Do not force the tool. Use the
correct tool for the application. The
correct tool will do the job better and
safer at the rate for which the tool is
designed.
c.
Do not use the tool if the switch
does not turn the tool on or off.
Any tool that cannot be controlled
with the switch is dangerous and
must be repaired.
d.
Disconnect the tool from the
air source before making
any adjustments, changing
accessories, or storing the tool.
Such preventive safety measures
reduce the risk of starting the tool
unintentionally. Turn off and detach
the air supply, safely discharge any
residual air pressure, and release the
throttle and/or turn the switch to its off
position before leaving the work area.
For technical questions, please call 1-800-444-3353.
Page 3
e.
Store the tool when it is idle out
of reach of children and other
untrained persons. A tool is
dangerous in the hands of untrained
users.
f.
Maintain the tool with care. Keep
a cutting tool sharp and clean. A
properly maintained tool, with sharp
cutting edges reduces the risk of
binding and is easier to control.
g.
Check for misalignment or binding
of moving parts, breakage of
parts, and any other condition
that affects the tool’s operation.
If damaged, have the tool serviced
before using. Many accidents are
caused by poorly maintained tools.
There is a risk of bursting if the tool is
damaged.
h.
Use only accessories that are
identified by the manufacturer for
the specific tool model. Use of an
accessory not intended for use with
the specific tool model, increases the
risk of injury to persons.
Service
pressurizing the tool may cause
bursting, abnormal operation, breakage of the tool or serious injury to
persons. Use only clean, dry, regulated compressed air at the rated
pressure or within the rated pressure
range as marked on the tool. Always
verify prior to using the tool that the
air source has been adjusted to the
rated air pressure or within the rated
air-pressure range.
b.
Never use oxygen, carbon dioxide,
combustible gases or any bottled
gas as an air source for the tool.
Such gases are capable of explosion
and serious injury to persons.
SAVE THESE
INSTRUCTIONS.
SYMBOLS AND
SPECIFIC SAFETY
INSTRUCTIONS
Symbol Definitions
Symbol
Property or statement
a.
Tool service must be performed
only by qualified repair personnel.
b.
When servicing a tool, use only
identical replacement parts. Use
only authorized parts.
.../min
PSI
Pounds per square inch of pressure
Use only the lubricants supplied
with the tool or specified by the
manufacturer.
ft-lb
Foot-pounds of torque
BPM
Blows per minute
CFM
Cubic Feet per Minute flow
c.
Air source
a.
SKU 65940
Never connect to an air
source that is capable of
exceeding 90 PSI. Over
no
No-load speed
Revolutions or reciprocation per
minute
Cubic Feet per Minute flow at
standard conditions
Chart continued in next column.
SCFM
For technical questions, please call 1-800-444-3353.
Page 4
do this type of work. To reduce your
exposure to these chemicals: work in
a well ventilated area, and work with
approved safety equipment, such as
those dust masks that are specially
designed to filter out microscopic
particles. (California Health & Safety
Code § 25249.5, et seq.)
WARNING: The brass components
of this product contain lead, a
chemical known to the State of
California to cause birth defects (or
other reproductive harm). (California
Health & Safety code § 25249.5, et
seq.)
Symbol Definitions
Symbol
Property or statement
NPT
National pipe thread, tapered
NPS
National pipe thread, straight
WARNING marking concerning Risk
of Eye Injury. Wear ANSI-approved
eye protection.
WARNING marking concerning Risk
of Hearing Loss. Wear hearing
protection.
WARNING marking concerning Risk
of Respiratory Injury. Wear NIOSHapproved dust mask/respirator.
WARNING marking concerning Risk
of Explosion.
3.
Only use with accessories rated to
handle the forces exerted by this tool
during operation. Other accessories
not designed for the forces generated
may break and forcefully launch
pieces.
4.
Attach all accessories properly to the
tool before connecting the air supply.
A loose accessory may detach or
break during operation.
5.
Obey the manual for the air
compressor used to power this tool.
6.
Install an in-line shutoff valve to allow
immediate control over the air supply
in an emergency, even if a hose is
ruptured.
7.
Remove plastic cap from air inlet
before use.
8.
Use this tool with both hands only.
Using tools with only one hand can
result in loss of control.
9.
Do not lay the tool down until it has
come to a complete stop. Moving
parts can grab the surface and pull
the tool out of your control.
Specific Safety Instructions
1.
2.
The warnings and precautions
discussed in this manual cannot
cover all possible conditions and
situations that may occur. It must
be understood by the operator that
common sense and caution are
factors which cannot be built into this
product, but must be supplied by the
operator.
WARNING: Some dust created by
power sanding, sawing, grinding,
drilling, and other construction
activities, contains chemicals
known [to the State of California] to
cause cancer, birth defects or other
reproductive harm. Some examples
of these chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks and
cement or other masonry products
• Arsenic and chromium from
chemically treated lumber
Your risk from these exposures
varies, depending on how often you
SKU 65940
For technical questions, please call 1-800-444-3353.
Page 5
SAVE THESE
INSTRUCTIONS.
Vibration Precautions
This tool vibrates during use.
Repeated or long-term exposure to
vibration may cause temporary or
permanent physical injury, particularly to
the hands, arms and shoulders. To reduce
the risk of vibration-related injury:
1.
2.
Anyone using vibrating tools regularly
or for an extended period should
first be examined by a doctor and
then have regular medical checkups to ensure medical problems are
not being caused or worsened from
use. Pregnant women or people
who have impaired blood circulation
to the hand, past hand injuries,
nervous system disorders, diabetes,
or Raynaud’s Disease should not
use this tool. If you feel any medical
or physical symptoms related to
vibration (such as tingling, numbness,
and white or blue fingers), seek
medical advice as soon as possible.
Do not smoke during use. Nicotine
reduces the blood supply to the
hands and fingers, increasing the risk
of vibration-related injury.
3.
Wear suitable gloves to reduce the
vibration effects on the user.
4.
Use tools with the lowest vibration
when there is a choice between
different processes.
5.
Include vibration-free periods each
day of work.
6.
Grip tool as lightly as possible (while
still keeping safe control of it). Let
the tool do the work.
7.
To reduce vibration, maintain tool as
explained in this manual. If abnormal
vibration occurs, stop immediately.
SKU 65940
FUNCTIONAL DESCRIPTION
Specifications
Maximum Air Pressure
Air Inlet
Maximum Speed*
Average Air Consumption
Arbor/Chuck Capacity
90 PSI
1/4" -18 NPT Female
1800 RPM
5 SCFM @ 90 PSI
1/4" Drive Opening
* Maximum speed at stated maximum air pressure.
Excess air pressure is hazardous and may cause the
tool to exceed stated maximum speed.
Components and Controls
Trigger (4)
Selector Lever (10)
Figure 1
1.
Reversible feature controlled by the
Selector Lever (10) next to the Trigger (4) (See Fig. 1, above.) Move
switch up “F” for forward and down
“R” for reverse
INITIAL TOOL SET UP/
ASSEMBLY
Read the ENTIRE IMPORTANT
SAFETY INFORMATION
section at the beginning of this
manual including all text under
subheadings therein before set
up or use of this product.
For technical questions, please call 1-800-444-3353.
Page 6
Note: For additional information regarding
the parts listed in the following pages,
refer to the Assembly Diagram near
the end of this manual.
and filter for best service, as shown
in the diagram above. An in-line
shutoff valve is an important safety
device because it can shut off air
flow if the air hose is ruptured.
(See Fig. 2.)
Unpacking
When unpacking, make sure the item
is intact and undamaged. If any parts
are missing or broken, call Harbor Freight
Tools at the number shown throughout the
manual as soon as possible.
• This air tool may be shipped with a
protective plug covering the air inlet.
Remove this plug before set up.
Air Supply
Note: If an automatic oiler system is not
used, add a few drops of Pneumatic
Tool Oil to the airline connection
before operation. Add a few more
drops after each hour of continual
use. Oiling location is engraved into
the bottom of the handle next to the
Screwdriver’s air inlet.
2.
TO PREVENT
EXPLOSION:
Use only clean, dry, regulated,
compressed air to power tool.
Do not use oxygen, carbon
dioxide, combustible gases,
or any other bottled gas as a
power source for this tool.
Attach an air hose to the
compressor’s air outlet. Connect
the air hose to the air inlet of the
tool. Other components, such as
a connector and quick coupler, will
make operation more efficient, but
are not required.
WARNING! TO PREVENT SERIOUS
INJURY FROM ACCIDENTAL
OPERATION: Do not install a
female quick coupler on the tool.
Such a coupler contains an air valve
that will allow the air tool to retain
pressure and operate accidentally
after the air supply is disconnected.
Note: Air flow, and therefore tool
performance, can be hindered by
undersized air supply components.
Figure 2
1.
Incorporate an in-line oiler, shut-off
valve, regulator with pressure gauge,
SKU 65940
3.
The air hose must be long enough
to reach the work area with enough
extra length to allow free movement
while working.
4.
Make sure the tool’s throttle or
switch is in the off position; refer to
Operation section for description of
controls.
For technical questions, please call 1-800-444-3353.
Page 7
5.
Close the in-line safety valve between
the compressor and the tool.
6.
Turn on the air compressor according
to the manufacturer’s directions and
allow it to build up pressure until it
cycles off.
7.
Adjust the air compressor’s output
regulator so that the air output is
enough to properly power the tool,
but the output will not exceed the
tool’s maximum air pressure at any
time. Adjust the pressure gradually,
while checking the air output gauge
to set the right pressure range.
8.
Inspect the air connections for leaks.
Repair any leaks found.
9.
If the tool will not be used at this
time, turn off and detach the air
supply, safely discharge any
residual air pressure, and release
the throttle and/or turn the switch to
its off position to prevent accidental
operation.
Note: Residual air pressure should not be
present after the tool is disconnected
from the air supply. However, it is a
good safety measure to attempt to
discharge the tool in a safe fashion
after disconnecting to ensure that the
tool is disconnected and unpowered.
OPERATING INSTRUCTIONS
Read the ENTIRE IMPORTANT
SAFETY INFORMATION
section at the beginning of this
manual including all text under
subheadings therein before set
up or use of this product.
Inspect tool before use, looking
for damaged, loose, and
SKU 65940
missing parts. If any problems
are found, do not use tool until
repaired.
Tool Set Up
TO PREVENT
SERIOUS INJURY
FROM ACCIDENTAL
OPERATION: Turn off the tool,
detach the air supply, safely
discharge any residual air
pressure in the tool, and
release the throttle and/or turn
the switch to its off position
before performing any
inspection, maintenance, or
cleaning procedures.
TO PREVENT SERIOUS
INJURY: Do not adjust or
tamper with any control or
component in a way not
specifically explained within
this manual. Improper
adjustment can result in
tool failure or other serious
hazards.
1.
Wrap 3-4 turns of pipe thread sealing
tape over the 1/4” fitting at the end of
the hose. Attach the tool to the fitting
and tighten with a wrench.
Note: If you are not using an automatic
oiler system, before operation, add a
few drops of Pneumatic Tool Oil to the
airline connection. Add a few drops
more after each hour of continual
use.
2.
Set the air pressure on your compressor
to 90 PSI. Do not exceed the maximum
air pressure of 90 PSI.
3.
Check the air connection for leaks.
Warning! Always disconnect the unit from
the air compressor when changing
For technical questions, please call 1-800-444-3353.
Page 8
bits.
4.
2.
This tool has a pre-set torque. In
order to customize it to your particluar
job at hand, attach a Brass Air Inline
Regulator (available at Harbor Freight
Tools). Run a few tests on a scrap
workpiece to set the flow at the desired
rate, to limit schrew penetration in the 3.
workpiece.
Work Piece and Work Area Set Up
1.
Designate a work area that is clean
and well-lit. The work area must not
allow access by children or pets to
prevent injury and distraction.
2.
Route the air hose along a safe
route to reach the work area without
creating a tripping hazard or exposing
the air hose to possible damage.
The air hose must be long enough
to reach the work area with enough
extra length to allow free movement
while working.
3.
Secure loose workpieces using a vise
or clamps (not included) to prevent
movement while working.
4.
There must not be hazardous objects
(such as utility lines or foreign
objects) nearby that will present a
hazard while working.
General Operating Instructions
1.
If an automatic oiler is not used, add
a few drops of Pneumatic Tool Oil
to the airline connection before use.
Add a few drops more after each
hour of continual use.
SKU 65940
If the tool requires more force to
accomplish the task, verify that the
tool receives sufficient, unobstructed
airflow (CFM) and increase the
pressure (PSI) output of the regulator
up to the maximum air pressure
rating of this tool.
CAUTION! TO PREVENT TOOL
AND ACCESSORY FAILURE,
RESULTING IN INJURY:
Do not exceed the tool’s maximum
air pressure rating (90 PSI). If the
tool still does not have sufficient force
at maximum pressure and sufficient
airflow, then a larger tool may be
required.
4.
Fully insert the Drive Bit (50) into
Chuck Housing (41). Check that it
is straight.
5.
Set Selector Lever (10) for desired
rotational direction.
Note: Always use bits with undamaged tips.
Dull or damaged bits may cause undue
stress on the Screwdriver and possibly
break causing injury. Bits are available
at Harbor Freight Tools.
6.
Press the Trigger (4) to activate.
Warning! After use, the Driver Bit will be
extremely hot. Do not touch it until it
has had ample time to cool down.
7.
Note: To reverse the Pistol’s direction,
release pressure on Trigger (4) allowing
the tool to come to a complete stop,
then flip the Lever on the handle down.
(See Fig.1, page 6).
8.
To prevent accidents, turn off the tool,
detach the air supply, safely discharge
any residual air pressure in the tool,
and release the throttle and/or turn
the switch to its off position after use.
Clean external surfaces of the tool with
clean, dry cloth. Then store the tool
indoors out of children’s reach.
For technical questions, please call 1-800-444-3353.
Page 9
USER-MAINTENANCE
INSTRUCTIONS
Procedures not specifically
explained in this manual
must be performed only by a
qualified technician.
TO PREVENT
SERIOUS INJURY
FROM ACCIDENTAL
OPERATION:
Turn off the tool, detach the
air supply, safely discharge
any residual air pressure in
the tool, and release the
throttle and/or turn the switch
to its off position before
performing any inspection,
maintenance, or cleaning
procedures.
TO PREVENT SERIOUS
INJURY FROM TOOL
FAILURE:
Do not use damaged
equipment. If abnormal
noise, vibration, or leaking
air occurs, have the problem
corrected before further use.
TO PREVENT EXPLOSION:
Lubricate the tool only
with specified lubricants.
Lubricate the air inlet
using only pneumatic tool
oil. Lubricate the internal
mechanism using only
white lithium grease. Other
lubricants may damage the
mechanism and may be
highly flammable, causing an
explosion.
SKU 65940
Cleaning, Maintenance, and
Lubrication
Note: These procedures are in addition to
the regular checks and maintenance
explained as part of the regular
operation of the air-operated tool.
1.
Daily - Air Supply Maintenance:
Every day, perform maintenance
on the air supply according to
the component manufacturers’
instructions. The lubricator’s oil
level needs to be maintained and
the moisture filter must be regularly
drained. Performing routine
maintenance on the air supply will
allow the tool to operate more safely
and will also reduce wear on the tool.
2.
Weekly - Grease Lubrication:
Lubricate the internal mechanism of
the tool.
3.
Quarterly (every 3 months) - Tool
Disassembly, Cleaning, and
Inspection:
Have the internal mechanism
cleaned, inspected, and lubricated by
a qualified technician. If the vanes
need replacement, all vanes should
be replaced as a set.
For technical questions, please call 1-800-444-3353.
Page 10
Troubleshooting
Problem
Possible Causes
Decreased output. 1. Not enough air pressure and/
or air flow.
2. Obstructed trigger.
Likely Solutions
1. Check for loose connections and make sure
that air supply is providing enough air flow
(CFM) at required pressure (PSI) to the
tool’s air inlet. Do not exceed maximum air
pressure.
2. Clean around trigger to ensure free
movement.
3. Lubricate using air tool oil and grease
according to directions.
4. Clean air inlet screen of buildup.
3. Incorrect lubrication or not
enough lubrication.
4. Blocked air inlet screen (if
equipped).
5. Air leaking from loose housing. 5. Make sure housing is properly assembled
and tight.
6. Mechanism contaminated.
6. Have qualified technician clean and lubricate
mechanism. Install in-line filter in air supply
as stated in Initial Set Up: Air Supply.
7. Vane wear or damage.
7. Replace all vanes.
Housing heats
1. Incorrect lubrication or not
1. Lubricate using air tool oil and grease
during non stop
enough lubrication.
according to directions.
continuous use.
2. Worn parts.
2. Have qualified technician inspect internal
mechanism and replace parts as needed.
Severe air
1. Cross-threaded housing
1. Check for incorrect alignment and uneven
leakage.
components.
gaps. If cross-threaded, disassemble and
(Slight air leakage
replace damaged parts before use.
is normal,
2. Loose housing.
2. Tighten housing assembly. If housing cannot
especially on older
tighten properly, internal parts may be
tools.)
misaligned.
3. Damaged valve or housing.
3. Replace damaged components.
4. Dirty, worn or damaged valve. 4. Clean or replace valve assembly.
Follow all safety precautions whenever diagnosing or servicing the
tool. Disconnect air supply before service.
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not
available individually as replacement parts.
SKU 65940
For technical questions, please call 1-800-444-3353.
Page 11
PARTS LIST
Part
1
2
3
4
5
6
7
8
9
10
11
13
14
15
16
17
18
19
20
21
22
23
24
25
Description
Housing
Pin
Air Inlet
Trigger
Valve Stem
Reverse Bushing
O-Ring
Valve Spring
O-Ring
Selector Lever
Motor Gasket
Ball Bearing
End Plate
Rotor
Rotor Blade
Pin
Cylinder
Spacer
Spring
Spring Guide
Internal Gear
Gear
Pin
Bushing
PARTS LIST
Q’ty
1
1
1
1
1
1
1
1
1
1
1
2
2
1
5
1
1
1
1
1
1
3
3
3
Part
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
46
47
48
49
50
Description
Work Spindle
Ball Bearing
Clamp Nut
Driver
Retaining Ring
Retaining Ring
Cam Spindle
Steel Ball
Clutch Carrier
Steel Ball
Washer
Spring
Washer
Adjusting Nut
Spacer
Chuck Housing
Ball Retainer
Spring
Washer
Set Screw
O-Ring
Exhaust Diffuser
Screw
Double-Ended Driver Bit
Q’ty
1
1
1
1
3
1
1
1
1
4
1
1
1
1
1
1
1
1
1
1
1
1
2
1
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT
HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR
DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE
UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER
ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL
PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION
OF REPLACEMENT PARTS THERETO.
SKU 65940
For technical questions, please call 1-800-444-3353.
Page 12
ASSEMBLY DIAGRAM
Please Note: Double-Ended Drive Bit (50) not shown
SKU 65940
For technical questions, please call 1-800-444-3353.
Page 13
90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet
high quality and durability standards, and warrants to the original purchaser that
this product is free from defects in materials and workmanship for the period
of 90 days from the date of purchase. This warranty does not apply to damage
due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or
alterations outside our facilities, criminal activity, improper installation, normal
wear and tear, or to lack of maintenance. We shall in no event be liable for
death, injuries to persons or property, or for incidental, contingent, special or
consequential damages arising from the use of our product. Some states do
not allow the exclusion or limitation of incidental or consequential damages, so
the above limitation of exclusion may not apply to you. THIS WARRANTY IS
EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us
with transportation charges prepaid. Proof of purchase date and an explanation
of the complaint must accompany the merchandise. If our inspection verifies the
defect, we will either repair or replace the product at our election or we may elect
to refund the purchase price if we cannot readily and quickly provide you with a
replacement. We will return repaired products at our expense, but if we determine
there is no defect, or that the defect resulted from causes not within the scope of
our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights
which vary from state to state.
SKU 65940
For technical questions, please call 1-800-444-3353.
Page 14