Extron electronics | Dual Link DVI Transmitter and Receiver DVI DL 201 Rx | User guide | Extron electronics Dual Link DVI Transmitter and Receiver DVI DL 201 Rx User guide

User Guide
DVI & HDMI®
DVI DL 201 Tx/Rx
Dual Link DVI Transmitter and Receiver
68-1531-01 Rev. C
11 10
Precautions
Safety Instructions • English
Warning
This symbol is intended to alert the user of important operating and maintenance
(servicing) instructions in the literature provided with the equipment.
Power sources • This equipment should be operated only from the power source indicated on the product. This
equipment is intended to be used with a main power system with a grounded (neutral) conductor. The
third (grounding) pin is a safety feature, do not attempt to bypass or disable it.
This symbol is intended to alert the user of the presence of uninsulated dangerous
voltage within the product enclosure that may present a risk of electric shock.
Power disconnection • To remove power from the equipment safely, remove all power cords from the rear of
the equipment, or the desktop power module (if detachable), or from the power source receptacle (wall
plug).
Caution
Read Instructions • Read and understand all safety and operating instructions before using the equipment.
Retain Instructions • The safety instructions should be kept for future reference.
Follow Warnings • Follow all warnings and instructions marked on the equipment or in the user
information.
Avoid Attachments • Do not use tools or attachments that are not recommended by the equipment
manufacturer because they may be hazardous.
Consignes de Sécurité • Français
Power cord protection • Power cords should be routed so that they are not likely to be stepped on or pinched by
items placed upon or against them.
Servicing • Refer all servicing to qualified service personnel. There are no user-serviceable parts inside. To
prevent the risk of shock, do not attempt to service this equipment yourself because opening or removing
covers may expose you to dangerous voltage or other hazards.
Slots and openings • If the equipment has slots or holes in the enclosure, these are provided to prevent
overheating of sensitive components inside. These openings must never be blocked by other objects.
Lithium battery • There is a danger of explosion if battery is incorrectly replaced. Replace it only with the
same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the
instructions of the manufacturer.
Avertissement
Ce symbole sert à avertir l’utilisateur que la documentation fournie avec le matériel
contient des instructions importantes concernant l’exploitation et la maintenance
(réparation).
Alimentations• Ne faire fonctionner ce matériel qu’avec la source d’alimentation indiquée sur l’appareil. Ce
matériel doit être utilisé avec une alimentation principale comportant un fil de terre (neutre). Le troisième
contact (de mise à la terre) constitue un dispositif de sécurité : n’essayez pas de la contourner ni de la
désactiver.
Ce symbole sert à avertir l’utilisateur de la présence dans le boîtier de l’appareil
de  tensions dangereuses non isolées posant des risques d’électrocution.
Déconnexion de l’alimentation• Pour mettre le matériel hors tension sans danger, déconnectez tous les cordons
d’alimentation de l’arrière de l’appareil ou du module d’alimentation de bureau (s’il est amovible) ou
encore de la prise secteur.
Attention
Lire les instructions• Prendre connaissance de toutes les consignes de sécurité et d’exploitation avant
d’utiliser le matériel.
Conserver les instructions• Ranger les consignes de sécurité afin de pouvoir les consulter à l’avenir.
Respecter les avertissements • Observer tous les avertissements et consignes marqués sur le matériel ou
présentés dans la documentation utilisateur.
Eviter les pièces de fixation • Ne pas utiliser de pièces de fixation ni d’outils non recommandés par le
fabricant du matériel car cela risquerait de poser certains dangers.
Protection du cordon d’alimentation • Acheminer les cordons d’alimentation de manière à ce que personne ne
risque de marcher dessus et à ce qu’ils ne soient pas écrasés ou pincés par des objets.
Réparation-maintenance • Faire exécuter toutes les interventions de réparation-maintenance par un technicien
qualifié. Aucun des éléments internes ne peut être réparé par l’utilisateur. Afin d’éviter tout danger
d’électrocution, l’utilisateur ne doit pas essayer de procéder lui-même à ces opérations car l’ouverture ou le
retrait des couvercles risquent de l’exposer à de hautes tensions et autres dangers.
Fentes et orifices • Si le boîtier de l’appareil comporte des fentes ou des orifices, ceux-ci servent à empêcher
les composants internes sensibles de surchauffer. Ces ouvertures ne doivent jamais être bloquées par des
objets.
Lithium Batterie • Il a danger d’explosion s’ll y a remplacment incorrect de la batterie. Remplacer uniquement
avec une batterie du meme type ou d’un ype equivalent recommande par le constructeur. Mettre au reut les
batteries usagees conformement aux instructions du fabricant.
Sicherheitsanleitungen • Deutsch
Vorsicht
Dieses Symbol soll dem Benutzer in der im Lieferumfang enthaltenen
Dokumentation besonders wichtige Hinweise zur Bedienung und Wartung
(Instandhaltung) geben.
Stromquellen • Dieses Gerät sollte nur über die auf dem Produkt angegebene Stromquelle betrieben werden.
Dieses Gerät wurde für eine Verwendung mit einer Hauptstromleitung mit einem geerdeten (neutralen)
Leiter konzipiert. Der dritte Kontakt ist für einen Erdanschluß, und stellt eine Sicherheitsfunktion dar. Diese
sollte nicht umgangen oder außer Betrieb gesetzt werden.
Dieses Symbol soll den Benutzer darauf aufmerksam machen, daß im Inneren des
Gehäuses dieses Produktes gefährliche Spannungen, die nicht isoliert sind und
die einen elektrischen Schock verursachen können, herrschen.
Stromunterbrechung • Um das Gerät auf sichere Weise vom Netz zu trennen, sollten Sie alle Netzkabel
aus der Rückseite des Gerätes, aus der externen Stomversorgung (falls dies möglich ist) oder aus der
Wandsteckdose ziehen.
Achtung
Lesen der Anleitungen • Bevor Sie das Gerät zum ersten Mal verwenden, sollten Sie alle Sicherheits-und
Bedienungsanleitungen genau durchlesen und verstehen.
Aufbewahren der Anleitungen • Die Hinweise zur elektrischen Sicherheit des Produktes sollten Sie
aufbewahren, damit Sie im Bedarfsfall darauf zurückgreifen können.
Befolgen der Warnhinweise • Befolgen Sie alle Warnhinweise und Anleitungen auf dem Gerät oder in der
Benutzerdokumentation.
Keine Zusatzgeräte • Verwenden Sie keine Werkzeuge oder Zusatzgeräte, die nicht ausdrücklich vom
Hersteller empfohlen wurden, da diese eine Gefahrenquelle darstellen können.
Instrucciones de seguridad • Español
Schutz des Netzkabels • Netzkabel sollten stets so verlegt werden, daß sie nicht im Weg liegen und niemand
darauf treten kann oder Objekte darauf- oder unmittelbar dagegengestellt werden können.
Wartung • Alle Wartungsmaßnahmen sollten nur von qualifiziertem Servicepersonal durchgeführt werden.
Die internen Komponenten des Gerätes sind wartungsfrei. Zur Vermeidung eines elektrischen Schocks
versuchen Sie in keinem Fall, dieses Gerät selbst öffnen, da beim Entfernen der Abdeckungen die Gefahr
eines elektrischen Schlags und/oder andere Gefahren bestehen.
Schlitze und Öffnungen • Wenn das Gerät Schlitze oder Löcher im Gehäuse aufweist, dienen diese zur
Vermeidung einer Überhitzung der empfindlichen Teile im Inneren. Diese Öffnungen dürfen niemals von
anderen Objekten blockiert werden.
Litium-Batterie • Explosionsgefahr, falls die Batterie nicht richtig ersetzt wird. Ersetzen Sie verbrauchte
Batterien nur durch den gleichen oder einen vergleichbaren Batterietyp, der auch vom Hersteller
empfohlen wird. Entsorgen Sie verbrauchte Batterien bitte gemäß den Herstelleranweisungen.
Advertencia
Este símbolo se utiliza para advertir al usuario sobre instrucciones importantes
de operación y mantenimiento (o cambio de partes) que se desean destacar en el
contenido de la documentación suministrada con los equipos.
Alimentación eléctrica • Este equipo debe conectarse únicamente a la fuente/tipo de alimentación eléctrica
indicada en el mismo. La alimentación eléctrica de este equipo debe provenir de un sistema de distribución
general con conductor neutro a tierra. La tercera pata (puesta a tierra) es una medida de seguridad, no
puentearia ni eliminaria.
Este símbolo se utiliza para advertir al usuario sobre la presencia de elementos
con voltaje peligroso sin protección aislante, que puedan encontrarse dentro de la
caja o alojamiento del producto, y que puedan representar riesgo de electrocución.
Desconexión de alimentación eléctrica • Para desconectar con seguridad la acometida de alimentación eléctrica
al equipo, desenchufar todos los cables de alimentación en el panel trasero del equipo, o desenchufar el
módulo de alimentación (si fuera independiente), o desenchufar el cable del receptáculo de la pared.
Precaucion
Leer las instrucciones • Leer y analizar todas las instrucciones de operación y seguridad, antes de usar el
equipo.
Conservar las instrucciones • Conservar las instrucciones de seguridad para futura consulta.
Obedecer las advertencias • Todas las advertencias e instrucciones marcadas en el equipo o en la
documentación del usuario, deben ser obedecidas.
Evitar el uso de accesorios • No usar herramientas o accesorios que no sean especificamente recomendados
por el fabricante, ya que podrian implicar riesgos.
安全须知 • 中文
这个符号提示用户该设备用户手册中有重要的操作和维护说明。
这个符号警告用户该设备机壳内有暴露的危险电压,有触电危险。
注意
阅读说明书 • 用户使用该设备前必须阅读并理解所有安全和使用说明。
保存说明书 • 用户应保存安全说明书以备将来使用。
遵守警告 • 用户应遵守产品和用户指南上的所有安全和操作说明。
避免追加 • 不要使用该产品厂商没有推荐的工具或追加设备,以避免危险。
Protección del cables de alimentación • Los cables de alimentación eléctrica se deben instalar en lugares donde
no sean pisados ni apretados por objetos que se puedan apoyar sobre ellos.
Reparaciones/mantenimiento • Solicitar siempre los servicios técnicos de personal calificado. En el interior no
hay partes a las que el usuario deba acceder. Para evitar riesgo de electrocución, no intentar personalmente
la reparación/mantenimiento de este equipo, ya que al abrir o extraer las tapas puede quedar expuesto a
voltajes peligrosos u otros riesgos.
Ranuras y aberturas • Si el equipo posee ranuras o orificios en su caja/alojamiento, es para evitar el
sobrecalientamiento de componentes internos sensibles. Estas aberturas nunca se deben obstruir con otros
objetos.
Batería de litio • Existe riesgo de explosión si esta batería se coloca en la posición incorrecta. Cambiar esta
batería únicamente con el mismo tipo (o su equivalente) recomendado por el fabricante. Desachar las
baterías usadas siguiendo las instrucciones del fabricante.
警告
电源 • 该设备只能使用产品上标明的电源。 设备必须使用有地线的供电系统供电。 第三条线
(地线)是安全设施,不能不用或跳过 。
拔掉电源 • 为安全地从设备拔掉电源,请拔掉所有设备后或桌面电源的电源线,或任何接到市电
系统的电源线。
电源线保护 • 妥善布线, 避免被踩踏,或重物挤压。
维护 • 所有维修必须由认证的维修人员进行。 设备内部没有用户可以更换的零件。为避免出现触
电危险不要自己试图打开设备盖子维修该设备。
通风孔 • 有些设备机壳上有通风槽或孔,它们是用来防止机内敏感元件过热。 不要用任何东西
挡住通风孔。
锂电池 • 不正确的更换电池会有爆炸的危险。必须使用与厂家推荐的相同或相近型号的电池。按
照生产厂的建议处理废弃电池。
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15
of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
The Class A limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the user guide, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be
required to correct the interference at his own expense.
NOTE: This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used with
the unit to ensure compliance with FCC emissions limits.
For more information on safety guidelines, regulatory compliances, EMI/EMF compliance, accessibility, and
related topics, click here.
Notational Conventions Used in this Guide
TIP: A tip provides a suggestion to make setting up or working with the device easier.
NOTE: A note draws attention to important information.
CAUTION: A caution warns of things or actions that might damage the equipment.
WARNING: A warning warns of things or actions that might cause injury, death, or
other severe consequences.
Copyright
© 2010 Extron Electronics. All rights reserved.
Trademarks
All trademarks mentioned in this guide are the properties of their respective owners.
Contents
Introduction............................................. 1
Reference Information........................... 19
About the DVI DL 201 Tx/Rx............................. 1
Features............................................................ 2
Specifications.................................................. 19
Included Parts................................................. 22
Optional Accessories....................................... 22
Panels and Cabling.................................. 3
DVI DL 201 Tx Front Panel................................. 3
DVI DL 201 Tx Rear Panel.................................. 4
DVI DL 201 Rx Front Panel................................ 5
DVI DL 201 Rx Rear Panel................................. 5
Cable Connections and Switches...................... 6
DVI-D Input................................................... 6
DVI-D Output................................................ 6
Twisted Pair Output and Input....................... 7
DDC Switches............................................. 10
Control Pass-through.................................. 10
Power Input................................................ 12
Mounting................................................. 23
Tabletop Placement......................................... 23
Rack Mounting............................................... 23
UL Guidelines for Rack Mounting................ 23
Rack Mounting Procedure........................... 24
Under-desk Mounting..................................... 24
Through-desk Mounting................................. 24
Projector Mounting......................................... 24
Configuration and Operation................ 13
Configuration................................................. 13
Using the EDID Minder to Read and Store
EDID from a Display................................... 13
Using the EDID Minder with the
Default EDID.............................................. 14
Using Pass-through Mode with DDC
Routed to a Local Monitor......................... 15
Using Pass-through Mode with DDC
Routed to the Remote Display.................... 15
Setup and Operation...................................... 16
Troubleshooting.............................................. 17
DVI DL 201 Tx/Rx • Contents
v
DVI DL 201 Tx/Rx • Contents
vi
Introduction
This user guide contains information about the Extron® DVI DL 201 Tx/Rx signal
transmitter and receiver, with information on how to mount, install, and operate these
units.
In this guide, unless otherwise specified, the terms “DVI DL 201” and “DVI DL 201 Tx/Rx”
refer to both the transmitter (DVI DL 201 Tx) and the receiver (DVI DL 201 Rx). The term
“transmitter” refers to the DVI DL 201 Tx, and “receiver” refers to the DVI DL 201 Rx.
About the DVI DL 201 Tx/Rx
The DVI DL 201 Tx and DVI DL 201 Rx are dual link DVI transmitter/receiver units. They can
be purchased as a pair or as individual units.
Each purchased pair and each individual unit is shipped with a single external desktop
12 VDC power supply. A single power supply, connected to the transmitter, is able to
power both devices.
Using three CAT 5/5e/6/7 twisted pair cables, DVI-D signals can be extended up to
100 feet (30 m) at resolutions up to 2560x1600 @ 60 Hz. This is significantly further than
the 15 feet (5 m) specified for standard dual link DVI cables.
NOTES: The DVI DL 201 Tx/Rx works with unshielded twisted pair (UTP) cable or
shielded twisted pair (STP) cable. However, STP cables are required to ensure
FCC Class A and CE compliance.
Do not use skew-free cable. Extron strongly recommends DTP26 cable,
especially when using high resolutions such as 1920x1200, 1600x1200, or
2560x1600. DTP26 cable is available as non-plenum (part number 22-214-03)
or plenum (part number 22-215-03).
DVI DL 201 Tx/Rx • Introduction
1
CAT 7 Cables
up to 200 feet
L
RO
NT RU
CO TH
SS
PA Rx
Tx
UT
I-D
DV
CT
NE N
ON LA
T C TO
NO TS
DOTPU S
3
OU PUT
T
OU
2
Extron
DVI DL 201 Rx
EDID MINDER
DEFAULT EDID
REMOTE DDC
1
ID
ED
ORE
ST
ON
L
ON
1
2
T
I-D
PU
IN
Rx
S
RIE
SE
RS-232
3
F
OF
Dual Link
DVI Cable
TP
OU
LO
DV
I
DV
1
20
Dual Link DVI
Receiver
L
RO U
NT
CO -THR
SS
PA
Rx
Tx
UT
CA
O
P
UT
RS-232
®
100
WER
PO
V
12 MAX
INPUT
IR
RELAY
LINK
3
ACT
1
3
1
COM
RX
IPL
0.4A
TX
250
4
3
2
1
4
2
1
2
R
4
2
3
TCP/IP
Extron
DVI DL 201 Tx
VCR
DVD
DOC
CAM
P
LAPTO
PC
ON
OFF
Y
DISPLA
MUTE
N
SCREE
UP
N
SCREE
DOWN
Dual Link DVI
Transmitter
TouchLink™
Control
System
2560 x 1600 Flat Panel
Display with Dual-Link
DVI Input
Local Monitor
PC w/ Dual Link DVI
Output - 2560 x 1600
Figure 1. Typical Application for the DVI DL 201 Tx/Rx
Features
Transmits dual link DVI-D signals over three CAT 5/5e/6/7 cables — Standard twisted
pair cables provide an economical, easily installed cable solution.
Long distance transmission — Signals are transmitted up to 100 feet (30 m), which is
significantly further than the 15 feet (5 m) specified for standard dual link DVI cables.
Local monitor output — The transmitter has a DVI-D output for connection to a local
monitor.
DDC routing to local or remote display — A two pole switch allows the user to
determine whether Display Data Channel (DDC) signals are routed to the local or the
remote display device.
EDID Minder™ — The EDID Minder maintains continuous EDID (Extended Display
Identification Data) communication with the attached source. This ensures that the DVI
source powers up correctly and maintains a proper video output, even if the display is off.
Control communications pass-through — The DVI DL 201 passes through RS-232 (two
way) or IR (one way) control signals, to a remote display.
Compact design — The transmitter is 1U high, a half rack wide, and 3 inches deep for
easy rack mounting near the source device.
The receiver is 1 inch high, a quarter rack wide and 3 inches deep, allowing multiple
mounting options near the display device.
Remote powering of receiver — A single power supply, connected to the transmitter, is
able to power both the transmitter and receiver.
DVI DL 201 Tx/Rx • Introduction
2
Panels and
Cabling
This section describes the panel features and cabling of the DVI DL 201 Tx and
DVI DL 201 Rx:
zz
DVI DL 201 Tx Front Panel
zz
DVI DL 201 Tx Rear Panel
zz
DVI DL 201 Rx Front Panel
zz
DVI DL 201 Rx Rear Panel
DVI DL 201 Tx Front Panel
The illustration below shows the front panel features of the DVI DL 201 Tx.
DVI DL 201 Tx
DVI DUAL LINK TRANSMITTER
1
Figure 2. DVI DL 201 Tx Front Panel Features
a LED — An amber light indicates that the DVI DL 201 Tx is receiving power from a
power supply. A green light indicates that the transmitter is also receiving a video
signal.
DVI DL 201 Tx/Rx • Panels and Cabling
3
DVI DL 201 Tx Rear Panel
DVI DL 201 Tx
POWER
12V
0.4A MAX
EDID MINDER
DEFAULT EDID
REMOTE DDC
The illustration below shows the rear panel features of the DVI DL 201 Tx.
SN XXXXXXXX E XXXXX 00/00
DVI DL TX
LOCAL OUTPUT
DVI-D INPUT
EDID
STORE
ON ON
OFF
2
3
4
5
DO NOT CONNECT
OUTPUTS TO LAN
CONTROL
PASS THRU
1
OUTPUTS
2
3
Tx Rx
1 2 3
6
7
8
Figure 3. DVI DL 201 Tx Rear Panel Features
b Power input — The 12 VDC power supply (provided) connects to this two-pole,
3.5 mm captive screw connector.
c DVI-D input — One female DVI-I connector accepts a dual-link DVI-D input from the
source device.
d Local monitor output — One female DVI-I connector provides a dual-link DVI-D
output to the local monitor.
e EDID Minder Store switch and LED ­— When depressed, the transmitter reads and
stores the EDID information from the local monitor. The LED gives the status of this
process.
f DDC route switches — Three DIP switches allow the unit to be configured to use the
EDID Minder or route the DDC directly to the display.
g Control signal pass-through — A three-pole, 3.5 mm captive screw connector
inputs pass-through RS-232 (two-way) or IR signals (one-way).
h Twisted pair outputs — Three RJ-45 jacks are used for transmitting DVI video,
remote power, and communications/control signals.
NOTES: The DVI DL 201 transmits high frequency signals via these TP outputs.
Connections between the transmitter and receiver must be point to point.
It is recommended that there should be no couplers, adapter, or patch
panels between the transmitter and receiver units.
Do not use skew-free cable. Extron strongly recommends DTP26 cable,
especially when using high resolutions such as 1920x1200, 1600x1200,
or 2560x1600. DTP26 cable is available as non-plenum (part number
22‑214‑03) or plenum (part number 22-215-03).
DVI DL 201 Tx/Rx • Panels and Cabling
4
DVI DL 201 Rx Front Panel
The illustration below shows the front panel features of the DVI DL 201 Rx.
CONTROL
PASS THRU
DVI-D OUTPUT
Tx Rx
DVI 201 Rx SERIES
9
10
11
Figure 4. DVI DL 201 Rx Front Panel Features
i Power LED — An amber light indicates that the DVI DL 201 Rx is receiving power
from a power supply or remotely, through the transmitter. A green light indicates that
the receiver is also receiving a video signal.
j DVI-D output — One female DVI-I connector provides a dual-link DVI-D output.
k Control signal pass-through — A three-pole, 3.5 mm captive screw connector
inputs pass-through RS-232 (two-way) or IR signals (one-way).
DVI DL 201 Rx Rear Panel
The illustration below shows the rear panel features of the DVI DL 201 Rx.
1
INPUTS
2
3
DO NOT
CONNECT
INPUTS TO
LAN
12
DVI DL 201 Rx
POWER
12V
0.4A MAX
13
Figure 5. DVI DL 201 Rx Rear Panel Features
l Power input — An optional 12 VDC power supply (not provided) connects to this
two-pole, 3.5 mm captive screw connector.
NOTE: The receiver can be remotely powered by the transmitter.
m Twisted pair inputs — Three RJ-45 jacks receive video, remote power, and pass-
through communications/control signals from the transmitter. They can also send passthrough control signals via the transmitter.
NOTES: The DVI DL 201 transmits high frequency signals via these TP outputs.
Connections between the transmitter and receiver must be point to point.
It is recommended that there should be no couplers, adapter, or patch
panels between the transmitter and receiver units.
Do not use skew-free cable. Extron strongly recommends DTP26 cable,
especially when using high resolutions such as 1920x1200, 1600x1200,
or 2560x1600. DTP26 cable is available as non-plenum (part number
22‑214‑03) or plenum (part number 22-215-03).
DVI DL 201 Tx/Rx • Panels and Cabling
5
Cable Connections and Switches
DVI-D Input
Connect the DVI-D source device to the female DVI-I input connector.
The dual link DVI-D input carries a signal with a resolution up to 2560x1600 @ 60 Hz.
For sources providing HDMI signals, use an HDMI to DVI adapter, such as the Extron
HDMIF-DVIDM female HDMI to male DVI-D adapter (part number 26-616-01). The pin
assignments for the DVI-I input connectors are shown in the table below.
DVI-D Output
Connect the local display device to the female DVI-I output connector on the rear panel of
the transmitter and the remote display device to the output connector on the front panel
of the receiver.
The dual link DVI-D output carries a signal with a resolution up to 2560x1600 @ 60 Hz.
The pin assignments for the DVI-I output connectors are the same as those for the input
connectors and are shown in the table below.
NOTE: Although DVI-I connectors are used, the DVI DL 201 is compatible only with
DVI-D signals.
DVI Dual Link - Female
1
8
17
24
9
Pin
Signal
Pin
Signal
Pin
Signal
1
TMDS data 2–
9
TMDS data 1–
17
TMDS data 0–
2
TMDS data 2+
10
TMDS data 1+
18
TMDS data 0+
3
TMDS data
2/4 shield
11
TMDS data
1/3 shield
19
TMDS data
0/5 shield
4
TMDS data 4-
12
TMDS data 3-
20
TMDS data 5-
5
TMDS data 4+
13
TMDS data 3+
21
TMDS data 5+
6
DDC clock
14
+5 V power
22
TMDS clock
shield
7
DDC data
15
Ground
23
TMDS clock+
8
CEC control*
16
Hot plug detect 24
TMDS clock–
*CEC control on pin 8 is a proprietary usage and is not the
industry standard
DVI DL 201 Tx/Rx • Panels and Cabling
6
Twisted Pair Output and Input
Terminating shielded cable
CAT 5/5e/6/7 twisted pair cable is not provided with the transmitter/receiver pair. You
may purchase cables that have been precut to the required length and terminated to the
T586A or T586B standard (see the table on the next page).
Alternatively, purchase bulk cable and use the RJ-45 connectors (provided) to prepare your
own terminated cables as described below.
NOTE: The transmitter and receiver pair works with unshielded twisted pair (UTP) or
shielded twisted pair (STP) cables. To ensure FCC Class A and CE compliance,
and for optimum performance, STP cables are recommended.
Do not use skew-free cable. Extron strongly recommends DTP26 cable,
especially when using high resolutions such as 1920x1200, 1600x1200, or
2560x1600. DTP26 cable is available as non-plenum (part number 22‑214‑03)
or plenum (part number 22-215-03).
1. Cut the cables to the required length. All three cables should be the same length.
2. Remove about 7/8 inch (2.2 cm) of the outer coat. If using STP cable, peel back the
shielding and fold it over the top of the outer coat.
Peel back shield and
Fold back.
3. Cut away and discard the clear cellophane inner wrapper that extends beyond the
folded back shielding.
4. Cut a piece of self-adhesive shielded aluminum tape (provided), remove the backing,
and wrap it around the folded back shielding.
Aluminum Tape
Wrap tape around folded foil shielding.
(cut and save a portion for the
crimped connector tangs)
DVI DL 201 Tx/Rx • Panels and Cabling
7
5. Separate the individual wires, and arrange them so that all eight wires are side by side
in the same order as the T586A or T586B standard shown at the top of the next page.
Both ends of a cable must be wired to the same standard (T586A or T586B).
Pin #
TIA/EIA
T 586 A
Wire color
TIA/EIA
T 586 B
Wire color
Cable 1 Cable 2
Cable 3
1
White-green
White-orange Data 0+
CEC
Data 3+
2
Green
Orange
Data 0+
HPD
Data 3+
3
White-orange
White-green
IDCK+
RS-232 Tx/IR+
N/C
4
Blue
Blue
Data 1+
DDC Clock
Data 4+
5
White-blue
White-blue
Data 1+
+12 V
Data 4+
6
Orange
Green
IDCK-
RS-232 Rx
N/C
7
White-brown
White-brown
Data 2+
DDC Data
Data 5+
8
Brown
Brown
Data 2+
Ground
Data 5+
6. Feed the wires into the RJ-45 connector.
Line up wires per chart,
then insert into RJ-45
connector.
12345678
7. Crimp the cable in the normal manner (see the figure below), folding the tangs of the
connector over the shielded tape.
Crimped Connector
DVI DL 201 Tx/Rx • Panels and Cabling
8
Connections
Use RJ-45 connectors to link the output from the transmitter to the appropriate input on
the receiver. Three CAT 5/5e/6/7 twisted pair (TP) cables connect the transmitter with the
receiver.
NOTE: The transmitter and receiver pair works with unshielded twisted pair (UTP) or
shielded twisted pair (STP) cables. To ensure FCC Class A and CE compliance,
and for optimum performance, STP cables are recommended.
Connect the output from the transmitter to the input of the receiver that has the same
number:
zz
Transmitter port 1 connects to receiver port 1.
zz
Transmitter port 2 connects to receiver port 2.
zz
Transmitter port 3 connects to receiver port 3.
NOTE: Do not use skew-free cable. Extron strongly recommends DTP26 cable,
especially when using high resolutions such as 1920x1200, 1600x1200, or
2560x1600. DTP26 cable is available as non-plenum (part number 22‑214‑03)
or plenum (part number 22-215-03).
Single link/dual link DVI
Dual link DVI carries signals at resolutions up to 2560x1600 @ 60 Hz. Single link DVI
carries signals at resolutions up to 1920x1200 @ 60 Hz.
Video
Resolution
(60 Hz)
1024x768
720p
1080i
1920x1200
1600x1200
1080p
2560x1600
Single Link Mode
Dual Link Mode
UTP
STP/DTP26
UTP
STP/DTP26
200 feet
(60 m)
200 feet
(60 m)
200 feet
(60 m)
200 feet
(60 m)
100 feet
(30 m)
125 feet
(38 m)
100 feet
(30 m)
150 feet
(45 m)
N/A
N/A
100 feet
(30 m)
150 feet
(45 m)
NOTE: The transmission distance varies greatly depending on signal resolution and on
the type of cable, graphic card, and display used in the system.
To operate in dual link mode, all three TP cables are required and both the source and
display devices must support dual link DVI signals.
To operate in single link mode, only TP cables 1 and 2 are required. Dual link DVI is
backwards compatible with single link DVI.
The DVI/HDMI 201 (single link) receivers can be used with the DVI DL 201 transmitter, in
single link mode (using only TP cables 1 and 2).
DVI DL 201 Tx/Rx • Panels and Cabling
9
DDC Switches
When the DVI-D source device boots up, it uses the Display Data Channel (DDC), a twoway communication protocol, to obtain Extended Display Identification Data (EDID)
from the display device. This allows the source to output a resolution that matches the
capabilities of the display.
A bank of three switches allows the user to determine how the source device will obtain
the EDID. The EDID can be obtained directly from the display device, or from the internal
memory within. The three switches are:
Default EDID — When the Default EDID switch is on (factory default; see
figure at right), an EDID showing a typical dual link DVI display resolution of
2560x1600 @ 60 Hz is passed to the source device. The EDID Minder switch
must also be on for the Default EDID switch to function.
EDID MINDER
DEFAULT EDID
REMOTE DDC
EDID Minder — This switch must be on for the EDID Minder function to be
enabled. The factory default for this switch is the off position.
ON ON
OFF
Remote DDC — When this switch is off, the DDC is routed to the local
monitor. When the switch is on, the DDC is routed to the remote display device.
1 2 3
See page 13 for more information about configuring these switches to provide the source
device with the correct EDID.
Tx Rx
Control Pass-through
The DVI DL 201 Tx/Rx cannot be controlled by RS-232 or IR controls.
However, they are able to pass signals from a control device to a
remote device that is controlled by those signals.
NOTE: The RS-232 and IR communications are via a passive
pass-through only; the transmitter and receiver neither
generate nor respond to these signals.
Use the three-pole, 3.5 mm captive screw connector on the
transmitter to input RS‑232 or IR signals from a control device. Use
the corresponding connector on the receiver to pass signals to the
output display.
3/16" (5 mm)
MAX
Tx Rx
3-Pole
Captive Screw
Connector
NOTE: The ideal length of exposed wire in the stripping process is 3/16 inch (5 mm).
If longer than 3/16 inch, the exposed wires may touch, causing a short circuit.
If shorter than 3/16 inch, the wires can be easily pulled out even if tightly
fastened.
Do not tin the wires. Tinned wire does not hold its shape and comes loose
over time.
DVI DL 201 Tx/Rx • Panels and Cabling
10
RS-232 signals
CONTROL
PASS THRU
RS-232 signals are bidirectional — signals pass from the control
device and replies return from the remote device. To connect the
control device to the transmitter, or the receiver to the remote
device, make the following connections, as shown at right:
zz
Tx to Tx
zz
Rx to Rx
zz
DVI DL 201
Transmitter
or Receiver
Tx Rx
RS-232 Control
or Display Device
(ground) to
Tx Rx
NOTE: For information about controlling display devices with RS-232 commands,
please refer to the user guide of that device.
IR signals
IR signals are one-way (from control device to the IR emitter that
broadcasts the IR signal remotely). There are no responses and no
requirement for a reverse pathway. To connect the control device to
the transmitter or the receiver to the IR emitter, make the following
connections, as shown at right:
zz
The Signal (S), from the control device to Tx of the transmitter.
zz
The ground (G) of the control device is connected to the
ground ( ) of the transmitter.
zz
The Tx of the receiver to the S of the IR emitter.
zz
The ground ( ) of the receiver to the ground (G) of the IR emitter.
CONTROL
PASS THRU
DVI DL 201
Transmitter
or Receiver
Tx Rx
IR Control
or IR emitter
DVI DL 201 Tx/Rx • Panels and Cabling
S G
11
Power Input
1. Connect the captive screw connector from the supplied 12 VDC power supply into the
power receptacle.
CAUTION: Always use a power supply supplied by or specified by Extron. Use
of an unauthorized power supply voids all regulatory compliance
certification and may cause damage to the supply and the end
product.
Unless otherwise stated, the AC/DC adapters are not suitable for
use in air handling spaces or in wall cavities. The power supply is
to be located within the same vicinity as the Extron A/V processing
equipment in an ordinary location, Pollution Degree 2, secured to the
equipment rack within the dedicated closet, podium or desk.
The installation must always be in accordance with the applicable
provisions of National Electrical Code ANSI/NFPA 70, article 75 and the
Canadian Electrical Code part 1, section 16. The power supply shall
not be permanently fixed to building structure or similar structure.
Twisted pair cable 2, pin 5 carries a 12 VDC power signal. This remote powering
feature allows a single power supply, connected to the transmitter, to power both the
transmitter and receiver.
CAUTION: Power supply voltage polarity is critical. Incorrect voltage polarity
can damage the power supply, the transmitter, and/or the receiver.
Identify the ground ( ) lead by the ridges on the side of the cord (see
the figure below).
POWER
12V
0.4A MAX
Power Receptacle
Smooth
A
DC Power Cord
Captive Screw Connector
Ridges
A
SECTION A–A
Power Supply
Output Cord
Ground
+12 VDC
AC Power Cord
Figure 6.
External
Power Supply
(12 VDC, 1 A )
Connecting Power to DVI DL 201 Tx/Rx
NOTE: See the second note on page 10 for important information about wiring
captive screw connectors.
2. Connect the AC power cord of the power supply unit to a 110 or 220 VAC electrical
source.
3. When the transmitter or receiver is getting power, either directly from the power
supply or indirectly through the remote powering feature (receiver), the front panel
LED lights amber.
DVI DL 201 Tx/Rx • Panels and Cabling
12
Configuration
and Operation
This section provides information about:
zz
Configuration
zz
Setup and Operation
zz
Troubleshooting
Configuration
Using the EDID Minder to Read and Store EDID from a Display
During boot up, the DVI-D source device uses Display Data Channel (DDC) to obtain
Extended Display Identification Data (EDID) from the display device. This allows the output
signal to match the resolution and refresh rate of the display device.
The DVI DL 201 Tx/Rx uses the Extron EDID Minder, which allows the user to store and use
EDID from any display device. To use this feature, follow these steps:
1. Disconnect all devices and cables from the transmitter and receiver.
2. Connect the desired display to the Local Monitor output of the transmitter. For best
results, the cable for this connection should be 15 feet (4.5 m) or shorter.
3. Apply power to the transmitter and the display device. If necessary, connect the power
supply to the transmitter.
5. Set the Default EDID switch to the off (down) position (see the figure at
right).
6. Set the Remote DDC to the off (down) position to allow DDC routing to
go to the local monitor (see the figure at right).
EDID MINDER
DEFAULT EDID
REMOTE DDC
4. Set the EDID Minder switch on the transmitter to the on (up) position (see
the figure at right).
ON ON
1 2 3
OFF
NOTE: The EDID Minder extracts information only from the local
monitor, not from the remote display.
7. Press and release the EDID Minder Store button. The LED next to the
switch turns from green to amber. This indicates that the transmitter
is reading and extracting the EDID from the display connected to the
local monitor output.
EDID
STORE
When the information has been successfully extracted and stored in non-volatile
memory, the LED returns to green.
DVI DL 201 Tx/Rx • Configuration and Operation
13
8. Turn off the display and disconnect it from the transmitter.
9. Connect the transmitter to the receiver with the three twisted pair cables.
zz
Transmitter port 1 connects to receiver port 1.
zz
Transmitter port 2 connects to receiver port 2.
zz
Transmitter port 3 connects to receiver port 3.
10.Power up the transmitter and the receiver. A single power supply, connected to the
transmitter can provide power to both units through the remote power connection.
11.Connect the remote display to the receiver output. A local monitor display can also be
connected to the transmitter output at this time.
12.Connect the DVI source to the transmitter input.
13.Check that the transmitter switches are in the positions described in steps 4 to 6.
14.Power on the DVI source device. The source device reads and uses the EDID
information stored in the transmitter memory and boots up with that resolution.
15.Power on the remote (and local) display device(s).
NOTE: All display devices must be capable of handling resolutions equal to or
greater than that of the device used to set the EDID.
Using the EDID Minder with the Default EDID
EDID MINDER
DEFAULT EDID
REMOTE DDC
1. Set the EDID Minder switch to the on (up) position and the Default EDID switch to the
on (up) position (see the figure at right). The position of the Remote DDC switch is not
relevant.
2. Connect the source device to the transmitter input.
3. Connect the display device to the receiver output and, if required, the
local monitor to the transmitter output.
4. Connect the transmitter to the receiver with the three twisted pair cables.
zz
Transmitter port 1 connects to receiver port 1.
zz
Transmitter port 2 connects to receiver port 2.
zz
Transmitter port 3 connects to receiver port 3.
ON ON
OFF
1 2 3
5. Power on all devices.
6. The source boots using EDID showing a native resolution of 2560x1600, regardless of
the display device.
NOTE: All display devices must be capable of handling resolutions equal to or
greater than that of the device used to set the EDID.
DVI DL 201 Tx/Rx • Configuration and Operation
14
Using Pass-through Mode with DDC Routed to a Local Monitor
2. Connect the source device to the transmitter input.
3. Connect the display device to the receiver output and, if required, the
local monitor to the transmitter output.
EDID MINDER
DEFAULT EDID
REMOTE DDC
1. Set the EDID Minder switch to the off (down) position and the Default
EDID switch to the off (down) position (see the figure at right). The
position of the Remote DDC switch is not relevant.
ON ON
1 2 3
OFF
4. Connect the transmitter to the receiver with the three twisted pair cables.
zz
Transmitter port 1 connects to receiver port 1.
zz
Transmitter port 2 connects to receiver port 2.
zz
Transmitter port 3 connects to receiver port 3.
5. Power on the local monitor, the transmitter, and the receiver.
6. Boot up the source device. The source boots with the resolution and refresh rate of
the local monitor.
NOTE: Because the local monitor is the source of EDID, it must be powered on
before the source device is booted.
7. Power on the display device.
NOTE: The remote display device must be capable of handling a resolution equal
to or greater than that of the local monitor.
Using Pass-through Mode with DDC Routed to the Remote Display
NOTE: This is the factory default setting.
NOTE: Although DDC can be routed to the remote display, there may be
instances when the signals become corrupted or weak. In those cases, the
source device may be unable to boot up correctly.
1. Set the EDID Minder switch to the off (down) position and the Remote DDC switch to
the on (up) position (see the figure at right). The position of the Default EDID switch is
not relevant.
EDID MINDER
DEFAULT EDID
REMOTE DDC
2. Connect the source device to the transmitter input.
3. Connect the display device to the receiver output and, if required, the
local monitor to the transmitter output.
4. Connect the transmitter to the receiver with the three twisted pair cables.
zz
Transmitter port 1 connects to receiver port 1.
zz
Transmitter port 2 connects to receiver port 2.
zz
Transmitter port 3 connects to receiver port 3.
ON ON
OFF
1 2 3
5. Power on the remote display, the transmitter, and the receiver.
DVI DL 201 Tx/Rx • Configuration and Operation
15
6. Boot up the source device. The source boots with the resolution and refresh rate of
the remote display.
NOTE: Because the remote display is the source of EDID, it must be powered on
before the source device is booted.
7. Power on the local monitor, if required.
NOTE: The remote display device must be capable of handling a resolution equal
to or greater than that of the local monitor.
Setup and Operation
1. Determine which source will be used for the EDID information and configure the DDC
switches appropriately (see pages 13 to 16). If necessary, use the EDID Minder to read
and store information from a display (see pages 13 to 14).
2. Prepare twisted pair cables (see “Terminating shielded cable”).
3. Connect the transmitter to the receiver (see “Connections”)
4. Connect the source device to the transmitter (see “DVI‑D input”). Do not power on
the source device at this time.
5. Connect the display device to the receiver (see “DVI‑D output”). If required, connect
a local monitor to the transmitter.
6. If required, connect any RS-232 or IR control devices (see “Control pass-through”).
7. Connect the power supply to the transmitter (see “Power input”).
CAUTION: Read all the Cautions in the “Power Input” section.
8. Power on the display device.
9. Power on and boot up the source device.
DVI DL 201 Tx/Rx • Configuration and Operation
16
Troubleshooting
If the DVI DL 201 Tx/Rx does not provide a high quality output signal, check the following
possibilities before contacting your Extron representative (see the back cover for contact
information). Be sure to read all the suggestions as many of the issues have several
possible solutions.
No output signal — Check that the front panel LEDs for both the transmitter and
receiver are on (lit amber). If they are not, check the power supply connections to the
units.
If a single power supply is being used to power both units, it must be connected to the
transmitter.
NOTE: Do not try to power both units with a single power supply connected to the
receiver as that will not provide adequate power to the transmitter.
There are some circumstances, particularly with longer Unshielded Twisted Pair (UTP) cable
runs, where the receiver may not get adequate power. Under these circumstances, it may
be necessary to use two separate power supplies, one for the transmitter and one for the
receiver.
Insure all three twisted pair cables are firmly seated in the correct receptacles.
No output signal or poor quality signal — Check the integrity of the UTP or STP cables
between the transmitter and the receiver.
NOTES: The transmitter and receiver pair works with unshielded twisted pair (UTP) or
shielded twisted pair (STP) cables. To ensure FCC Class A and CE compliance,
and for optimum performance, STP cables are recommended.
Do not use skew-free cable. Extron strongly recommends DTP26 cable,
especially when using high resolutions such as 1920x1200, 1600x1200, or
2560x1600. DTP26 cable is available as non-plenum (part number 22‑214‑03)
or plenum (part number 22-215-03).
zz
Ensure that the twisted pair cables are terminated correctly and to the same standard
at both ends (see “Terminating shielded cable”).
zz
Ensure that each RJ-45 connector is firmly seated in its receptacle and that each
transmitter port is connected to the correct receiver port (see “Connections”).
zz
Ensure that the length of the twisted pair cable does not exceed the guidelines for
single link or dual link connections (see “Single link/dual link DVI“).
DVI DL 201 Tx/Rx • Configuration and Operation
17
Image loss or jitter — DVI signals run at very high frequency and are especially
susceptible to bad video connections, too many adapters, or cables that are too long. To
avoid loss of an image or introduction of image jitter:
zz
The DVI cable on the input to the transmitter or the output from the receiver should
not exceed 10 feet (3 m).
zz
Use only cable designed for DVI signals.
zz
Limit or avoid the use of adapters, patch panels, or couplers with the input DVI cables,
the output DVI cables, and/or the twisted pair cables. Additional links in the chain
reduce signal integrity and overall cable length performance.
zz
Always turn on the display before the DVI video source in order for the source to
retrieve the DDC from the display.
No video signal or incorrect resolution or refresh rate — If the source device is not
able to obtain EDID information when it is being powered on, it may not be able to send a
video signal or the signal may have the wrong resolution or refresh rate.
zz
Ensure that the DDC DIP switches are set correctly for the EDID source (see
“Configuration”).
zz
The source device must be powered on after the display device providing the EDID
source has been powered on.
Incorrect color or tint — Ensure that the twisted pair cables are terminated correctly and
to the same standard on both ends of the cable (see “Terminating Shielded Cable“).
Display device shows a flashing black or blue screen, snow, or other distortion —
A device that is not High-Bandwidth Digital Content Protection (HDCP) compliant may be
receiving HDCP-encrypted signals.
The DVI DL 201 Tx/Rx is compatible with HDCP signals only when the EDID Minder is
disabled. HDCP signals can be passed through to only one display (remote or local) and
only that display shows the signal correctly.
Signal on local monitor but not on remote display — Check that both output devices
(local and remote) can handle resolutions equal to or greater than the EDID source.
DVI DL 201 Tx/Rx • Configuration and Operation
18
Reference
Information
This section provides information about:
zz
Specifications
zz
Included Parts
zz
Optional Accessories
Specifications
Video
Maximum data rate����������������������� Maximum pixel clock��������������������� Resolution range���������������������������� Formats����������������������������������������� Standards�������������������������������������� 10 Gbps (3.3 Gbps per color)
330 MHz (165 MHz per link)
Up to 2560x1600 @ 60 Hz
RGB and YCbCr digital video
DVI 1.0, HDMI 1.2
Video input and loop-through— transmitter
Number/signal type������������������������ 1 dual link DVI-D* input
1 dual link DVI-D* local loop-through
Connectors������������������������������������ 2 DVI-I female (1 for input, 1 for loop-through)
NOTE: *Dual link DVI is backwards compatible with all single link DVI/HDMI
signals.
Interconnection between transmitter and receiver
Connectors������������������������������������ (3) RJ-45 per unit for 3 cables connecting the transmitter and
receiver
Termination standards�������������������� TIA/EIA T568A or T568B
Signal transmission distance
1920x1200 or 1080p @ 60 Hz
Extron DTP26 cable�������������������� Up to 150’ (45 m)
2560x1600 @ 60 Hz
CAT 5/5e/6 STP or Extron DTP26 Up to 125’ (38 m)
CAT 5/5e/6 UTP cable���������������� 100’ (30 m)
Longer distances are possible with lower rates.
NOTE: The transmission distance varies greatly depending on the signal resolution
and on the type of cable, graphics card, and display used in the system.
DVI DL 201 Tx/Rx • Reference Information
19
Video output— receiver
Number/signal type������������������������ 1 dual link DVI-D*
Connectors������������������������������������ 1 DVI-I female
NOTE: *Dual link DVI is backwards compatible with all single link DVI/HDMI
signals.
Control/remote — external device (pass-through)
Serial control port input
Transmitter�������������������������������� Receiver������������������������������������� Serial control port output
Transmitter�������������������������������� Receiver������������������������������������� RS-232 via (1) 3.5 mm, 3 pole captive screw connector
1 set of proprietary signals on a female RJ-45 jack
1 set of proprietary signals on a female RJ-45 jack
RS-232 via a 3.5 mm, 3 pole captive screw connector
NOTE: Protocol is mirrored between the transmitter and the receiver.
Serial control pin configurations����� Captive screw connectors: 1 = Tx, 2 = Rx, 3 = GND
General
Recommended cable type�������������� CAT 5/5e/6 (shielded or unshielded) or Extron DTP26
External power supply������������������� 100 VAC to 240 VAC, 50-60 Hz, 6 W max., external; to 12
VDC, 2 A, regulated
Power input requirements�������������� 12 VDC, 0.4 A for both transmitter and receiver
NOTE: Each transmitter and receiver can be powered locally by an external
power supply. The receiver can be powered remotely by a power supply
connected to the transmitter on the other end of the CAT 5/5e/6 or
Extron DTP26 cable.
Temperature/humidity�������������������� Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%,
noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%,
noncondensing
Cooling����������������������������������������� Convection, no vents
Mounting
Rack mount������������������������������� Yes, with optional 1U rack shelf
Furniture mount������������������������ Yes, with optional through-desk mounting kit
Pole mount�������������������������������� Yes, attachable to a projector pole mount using optional
mounting kit
Enclosure type������������������������������� Metal
Enclosure dimensions
DVI DL 201 TX��������������������������� 1.75" H x 8.75" W x 3.0" D (1U high, half rack wide)
4.4 cm H x 22.2 cm W x 7.6 cm D
(Depth excludes connectors.)
DVI DL 201 RX��������������������������� 1.0" H x 4.3" W x 3.0" D (quarter rack wide)
(2.5 cm H x 10.9 cm W x 7.6 cm D)
(Depth excludes connectors.)
Product weight������������������������������ Transmitter: 0.6 lbs (0.3 kg)
Receiver: 0.3 lbs (0.1 kg)
Transmitter and receiver: 0.9 lbs (0.4 kg)
Shipping weight���������������������������� 2 lbs (1 kg)
DVI DL 201 Tx/Rx • Reference Information
20
Vibration��������������������������������������� Regulatory compliance
Safety���������������������������������������� EMI/EMC����������������������������������� MTBF��������������������������������������������� Warranty��������������������������������������� ISTA 1A in carton (International Safe Transit Association)
CE, c-UL, UL
CE, C-tick, FCC Class A**, ICES, VCCI
30,000 hours
3 years parts and labor
NOTES: **FCC testing is conducted with STP (shielded twisted pair) cable.
All nominal levels are at ±10%.
Specifications are subject to change without notice.
DVI DL 201 Tx/Rx • Reference Information
21
Included Parts
Description
Part Number
(1 pair) DVI DL 201 Tx/Rx
60-957-01
or (1) DVI DL 201 Tx
60-957-12
or (1) DVI DL 201 Rx
60-957-13
(1) 12 VDC, 2A power supply
(32) self-adhesive, shielded aluminum tape strips
(6) RJ-45 connectors
(8) rubber feet
(1) Tweeker (screwdriver)
DVI DL 201 Tx/Rx Setup Guide
Optional Accessories
Description
Part Number
DTP26 Shielded Digital Twisted Pair Cable non-plenum 1000' (300 m)
22-214-03
DTP26 Shielded Digital Twisted Pair Cable plenum 1000’ (300 m)
22-215-02
DTP RJ-45 connectors for Extron DTP26 cable (10/pack)
101-105-01
RSF 123 (3.5 inches deep, 1U rack shelf kit)
60-190-20
RSB 123 (3.5 inches deep, 1U basic rack shelf)
60-604-21
RSU 126 (6 inches deep, 1U rack shelf kit)
60-190-10
RSB 126 (6 inches deep, 1U basic rack shelf)
60-604-11
RSU 129 (9.5 inches deep, 1U rack shelf kit)
60-190-01
RSB 129 (9.5 inches deep, 1U basic rack shelf)
60-604-02
PMK 300 Projector mounting kit
70-374-01
MBD 129 Through-desk mounting kit (for DVI DL 201 Rx)
70-077-02
MBD 123 Through-desk mounting kit (for DVI DL 201 Tx)
70-485-01
MBU 125 Under-desk mounting kit (for DVI DL 201 Rx)
70-077-01
MBU 123 Under-desk mounting kit (for DVI DL 201 Tx)
70-212-01
HDMIF-DVIDM female HDMI to male DVI-D adapter
26-616-01
DVI DL 201 Tx/Rx • Reference Information
22
Mounting
This section outlines the various mounting options available for the DVI DL 201 Tx/Rx:
Tabletop Placement
Rack Mounting
Under-desk Mounting
Through-desk Mounting
Projector Mounting
Tabletop Placement
Attach the four provided rubber feet to the bottom of the unit and place it in any
convenient location.
Rack Mounting
UL Guidelines for Rack Mounting
The following Underwriters Laboratories (UL) guidelines are relevant to the safe installation
of these products in a rack:
1. Elevated operating ambient temperature — If the unit is installed in a closed or
multi-unit rack assembly, the operating ambient temperature of the rack environment
may be greater than room ambient temperature. Therefore, install the equipment in
an environment compatible with the maximum ambient temperature (Tma: +122 °F,
+50 °C) specified by Extron.
2. Reduced air flow — Install the equipment in the rack so that the equipment gets
adequate air flow for safe operation.
3. Mechanical loading — Mount the equipment in the rack so that uneven mechanical
loading does not create a hazardous condition.
4. Circuit overloading — Connect the equipment to the supply circuit and consider the
effect that circuit overloading might have on overcurrent protection and supply wiring.
Appropriate consideration of the equipment nameplate ratings should be used when
addressing this concern.
5. Reliable earthing (grounding) — Maintain reliable grounding of rack-mounted
equipment. Pay particular attention to supply connections other than direct
connections to the branch circuit (such as the use of power strips).
DVI DL 201 Tx/Rx • Mounting
23
Rack Mounting Procedure
The unit can be mounted on any of these optional Extron rack systems:
zz
RSF 123: 3.5 inch deep, 1U rack shelf kit (part number 60-190-20)
zz
RSB 123: 3.5 inch deep, 1U basic rack shelf (part number 60-604-21)
zz
RSU 126: 6 inch deep, 1U rack shelf kit (part number 60-190-10)
zz
RSB 126: 6 inch deep, 1U basic rack shelf (part number 60-604-11)
zz
RSU 129: 9.5 inch deep, 1U rack shelf kit (part number 60-190-01)
zz
RSB 129: 9.5 inch deep, 1U basic rack shelf (part number 60-604-02)
To mount the scaler on a rack shelf, follow the instructions provided with the shelf
accessories.
Under-desk Mounting
Mount the unit under a desk or podium, using the optional Extron MBU 125 underdesk mounting kit (part number 70‑077‑01) for the DVI DL 201 Rx or the MBU 123 kit
(part number 70‑212‑01) for the DVI DL 201 Tx. Follow the instructions provided with the
appropriate kit.
Through-desk Mounting
Mount the unit through a desk or podium using the optional Extron MBD 129 through
desk mounting kit (part number 70-077-02) for the DVI DL 201 Rx or the MBD 123 kit
(part number 70‑485-01) for the DVI DL 201 Tx. Follow the instructions provided with the
appropriate kit.
Projector Mounting
Mount the DVI DL 201 Rx above a projector using the optional Extron PMK 300 Projector
mounting kit (part number 70-374-01) by following the instructions provided with the kit.
DVI DL 201 Tx/Rx • Mounting
24
Extron® Warranty
Extron Electronics warrants this product against defects in materials and workmanship for a period of
three years from the date of purchase; touchscreen display and overlay components are covered for 1
year. In the event of malfunction during the warranty period attributable directly to faulty workmanship
and/or materials, Extron Electronics will, at its option, repair or replace said products or components, to
whatever extent it shall deem necessary to restore said product to proper operating condition, provided
that it is returned within the warranty period, with proof of purchase and description of malfunction to:
USA, Canada, South America,
and Central America:
Extron Electronics
1001 East Ball Road
Anaheim, CA 92805
U.S.A.
Japan:
Extron Electronics, Japan
Kyodo Building, 16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
Europe, Africa, and the Middle East:
Extron Europe
Hanzeboulevard 10
3825 PH Amersfoort
The Netherlands
China:
Extron China
686 Ronghua Road
Songjiang District
Shanghai 201611
China
Asia:
Extron Asia
135 Joo Seng Road, #04-01
PM Industrial Bldg.
Singapore 368363
Singapore
Middle East:
Extron Middle East
Dubai Airport Free Zone
F12, PO Box 293666
United Arab Emirates, Dubai
This Limited Warranty does not apply if the fault has been caused by misuse, improper handling care,
electrical or mechanical abuse, abnormal operating conditions, or modifications made to the product that
were not authorized by Extron.
NOTE: If a product is defective, please call Extron and ask for an Application Engineer to receive an RA
(Return Authorization) number. This will begin the repair process.
USA: (714) 491-1500
Asia:+65.6383.4400
Europe:+31.33.453.4040
Japan:
+81.3.3511.7655
Units must be returned insured, with shipping charges prepaid. If not insured, you assume the risk of
loss or damage during shipment. Returned units must include the serial number and a description of the
problem, as well as the name of the person to contact in case there are any questions.
Extron Electronics makes no further warranties either expressed or implied with respect to the product
and its quality, performance, merchantability, or fitness for any particular use. In no event will Extron
Electronics be liable for direct, indirect, or consequential damages resulting from any defect in this
product even if Extron Electronics has been advised of such damage.
Please note that laws vary from state to state and country to country, and that some provisions of this
warranty may not apply to you.
Installation Checklist
…… Determine which source will be used for the EDID information and configure the DDC
switches appropriately (see pages 13 to 16). If necessary, use the EDID Minder to read and
store information from a display (see pages 13 to 14).
…… Prepare twisted pair cables (see “Terminating shielded cable”).
…… Connect the transmitter to the receiver (see “Connections”)
…… Connect the source device to the transmitter (see “DVI‑D input”). Do not power on the
source device at this time.
…… Connect the display device to the receiver (see “DVI‑D output”). If required, connect a local
monitor to the transmitter.
…… If required, connect any RS-232 or IR control devices (see “Control pass-through”).
…… Connect the power supply to the transmitter (see “Power input”).
CAUTION: Read all the Cautions in the “Power Input” section.
…… Power on the display device.
…… Power on and boot up the source device.
Extron USA - West
Headquarters
Extron USA - East
Extron Europe
Extron Asia
Extron Japan
Extron China
Extron Middle East
+800.633.9876
+800.633.9876
+800.3987.6673
+800.7339.8766
Inside Asia Only
+81.3.3511.7655
+81.3.3511.7656 FAX
+400.883.1568
Inside Europe Only
+971.4.2991800
+971.4.2991880 FAX
+1.919.863.1794
+1.919.863.1797 FAX
+31.33.453.4040
+31.33.453.4050 FAX
+65.6383.4400
+65.6383.4664 FAX
Inside USA/Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
Inside USA/Canada Only
© 2010 Extron Electronics All rights reserved. www.extron.com
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Download PDF

advertising