Extron electronics | VSW 2VGA A | User`s manual | Extron electronics VSW 2VGA A User`s manual

User’s Manual
VSW 2VGA A
2-Input, 1-output VGA and Audio Switcher
68-1111-01 Rev. D
11 09
Precautions
Safety Instructions • English
This symbol is intended to alert the user of important
operating and maintenance (servicing) instructions
in the literature provided with the equipment.
This symbol is intended to alert the user of the
presence of uninsulated dangerous voltage within
the product’s enclosure that may present a risk of
electric shock.
Caution
Read Instructions • Read and understand all safety and operating
instructions before using the equipment.
Retain Instructions • The safety instructions should be kept for future
reference.
Follow Warnings • Follow all warnings and instructions marked on the
equipment or in the user information.
Avoid Attachments • Do not use tools or attachments that are not
recommended by the equipment manufacturer because they may be
hazardous.
Consignes de Sécurité • Français
Ce symbole sert à avertir l’utilisateur que la
documentation fournie avec le matériel contient des
instructions importantes concernant l’exploitation et
la maintenance (réparation).
Ce symbole sert à avertir l’utilisateur de la présence
dans le boîtier de l’appareil de  tensions dangereuses
non isolées posant des risques d’électrocution.
Attention
Lire les instructions• Prendre connaissance de toutes les consignes de
sécurité et d’exploitation avant d’utiliser le matériel.
Conserver les instructions• Ranger les consignes de sécurité afin de pouvoir
les consulter à l’avenir.
Respecter les avertissements • Observer tous les avertissements et consignes
marqués sur le matériel ou présentés dans la documentation utilisateur.
Eviter les pièces de fixation • Ne pas utiliser de pièces de fixation ni d’outils
non recommandés par le fabricant du matériel car cela risquerait de poser
certains dangers.
Sicherheitsanleitungen • Deutsch
Dieses Symbol soll dem Benutzer in der im
Lieferumfang enthaltenen Dokumentation
besonders wichtige Hinweise zur Bedienung und
Wartung (Instandhaltung) geben.
Dieses Symbol soll den Benutzer darauf aufmerksam
machen, daß im Inneren des Gehäuses dieses
Produktes gefährliche Spannungen, die nicht isoliert
sind und die einen elektrischen Schock verursachen
können, herrschen.
Achtung
Lesen der Anleitungen • Bevor Sie das Gerät zum ersten Mal verwenden,
sollten Sie alle Sicherheits-und Bedienungsanleitungen genau durchlesen
und verstehen.
Aufbewahren der Anleitungen • Die Hinweise zur elektrischen Sicherheit
des Produktes sollten Sie aufbewahren, damit Sie im Bedarfsfall darauf
zurückgreifen können.
Befolgen der Warnhinweise • Befolgen Sie alle Warnhinweise und
Anleitungen auf dem Gerät oder in der Benutzerdokumentation.
Keine Zusatzgeräte • Verwenden Sie keine Werkzeuge oder Zusatzgeräte,
die nicht ausdrücklich vom Hersteller empfohlen wurden, da diese eine
Gefahrenquelle darstellen können.
Instrucciones de seguridad • Español
Este símbolo se utiliza para advertir al usuario
sobre instrucciones importantes de operación y
mantenimiento (o cambio de partes) que se desean
destacar en el contenido de la documentación
suministrada con los equipos.
Este símbolo se utiliza para advertir al usuario sobre
la presencia de elementos con voltaje peligroso sin
protección aislante, que puedan encontrarse dentro
de la caja o alojamiento del producto, y que puedan
representar riesgo de electrocución.
Precaucion
Leer las instrucciones • Leer y analizar todas las instrucciones de operación y
seguridad, antes de usar el equipo.
Conservar las instrucciones • Conservar las instrucciones de seguridad para
futura consulta.
Obedecer las advertencias • Todas las advertencias e instrucciones marcadas
en el equipo o en la documentación del usuario, deben ser obedecidas.
Evitar el uso de accesorios • No usar herramientas o accesorios que no
sean especificamente recomendados por el fabricante, ya que podrian
implicar riesgos.
Warning
Power sources • This equipment should be operated only from the power source
indicated on the product. This equipment is intended to be used with a main power
system with a grounded (neutral) conductor. The third (grounding) pin is a safety
feature, do not attempt to bypass or disable it.
Power disconnection • To remove power from the equipment safely, remove all power
cords from the rear of the equipment, or the desktop power module (if detachable),
or from the power source receptacle (wall plug).
Power cord protection • Power cords should be routed so that they are not likely to be
stepped on or pinched by items placed upon or against them.
Servicing • Refer all servicing to qualified service personnel. There are no userserviceable parts inside. To prevent the risk of shock, do not attempt to service
this equipment yourself because opening or removing covers may expose you to
dangerous voltage or other hazards.
Slots and openings • If the equipment has slots or holes in the enclosure, these are
provided to prevent overheating of sensitive components inside. These openings
must never be blocked by other objects.
Lithium battery • There is a danger of explosion if battery is incorrectly
replaced. Replace it only with the same or equivalent type recommended by
the manufacturer. Dispose of used batteries according to the manufacturer’s
instructions.
Avertissement
Alimentations• Ne faire fonctionner ce matériel qu’avec la source d’alimentation
indiquée sur l’appareil. Ce matériel doit être utilisé avec une alimentation principale
comportant un fil de terre (neutre). Le troisième contact (de mise à la terre) constitue
un dispositif de sécurité : n’essayez pas de la contourner ni de la désactiver.
Déconnexion de l’alimentation• Pour mettre le matériel hors tension sans danger,
déconnectez tous les cordons d’alimentation de l’arrière de l’appareil ou du module
d’alimentation de bureau (s’il est amovible) ou encore de la prise secteur.
Protection du cordon d’alimentation • Acheminer les cordons d’alimentation de
manière à ce que personne ne risque de marcher dessus et à ce qu’ils ne soient pas
écrasés ou pincés par des objets.
Réparation-maintenance • Faire exécuter toutes les interventions de réparationmaintenance par un technicien qualifié. Aucun des éléments internes ne peut être
réparé par l’utilisateur. Afin d’éviter tout danger d’électrocution, l’utilisateur ne doit
pas essayer de procéder lui-même à ces opérations car l’ouverture ou le retrait des
couvercles risquent de l’exposer à de hautes tensions et autres dangers.
Fentes et orifices • Si le boîtier de l’appareil comporte des fentes ou des orifices, ceux-ci
servent à empêcher les composants internes sensibles de surchauffer. Ces ouvertures
ne doivent jamais être bloquées par des objets.
Lithium Batterie • Il a danger d’explosion s’ll y a remplacment incorrect de la batterie.
Remplacer uniquement avec une batterie du meme type ou d’un ype equivalent
recommande par le constructeur. Mettre au reut les batteries usagees conformement
aux instructions du fabricant.
Vorsicht
Stromquellen • Dieses Gerät sollte nur über die auf dem Produkt angegebene
Stromquelle betrieben werden. Dieses Gerät wurde für eine Verwendung mit einer
Hauptstromleitung mit einem geerdeten (neutralen) Leiter konzipiert. Der dritte
Kontakt ist für einen Erdanschluß, und stellt eine Sicherheitsfunktion dar. Diese
sollte nicht umgangen oder außer Betrieb gesetzt werden.
Stromunterbrechung • Um das Gerät auf sichere Weise vom Netz zu trennen, sollten
Sie alle Netzkabel aus der Rückseite des Gerätes, aus der externen Stomversorgung
(falls dies möglich ist) oder aus der Wandsteckdose ziehen.
Schutz des Netzkabels • Netzkabel sollten stets so verlegt werden, daß sie nicht im
Weg liegen und niemand darauf treten kann oder Objekte darauf- oder unmittelbar
dagegengestellt werden können.
Wartung • Alle Wartungsmaßnahmen sollten nur von qualifiziertem Servicepersonal
durchgeführt werden. Die internen Komponenten des Gerätes sind wartungsfrei.
Zur Vermeidung eines elektrischen Schocks versuchen Sie in keinem Fall, dieses
Gerät selbst öffnen, da beim Entfernen der Abdeckungen die Gefahr eines
elektrischen Schlags und/oder andere Gefahren bestehen.
Schlitze und Öffnungen • Wenn das Gerät Schlitze oder Löcher im Gehäuse aufweist,
dienen diese zur Vermeidung einer Überhitzung der empfindlichen Teile im
Inneren. Diese Öffnungen dürfen niemals von anderen Objekten blockiert werden.
Litium-Batterie • Explosionsgefahr, falls die Batterie nicht richtig ersetzt
wird. Ersetzen Sie verbrauchte Batterien nur durch den gleichen oder einen
vergleichbaren Batterietyp, der auch vom Hersteller empfohlen wird. Entsorgen Sie
verbrauchte Batterien bitte gemäß den Herstelleranweisungen.
Advertencia
Alimentación eléctrica • Este equipo debe conectarse únicamente a la fuente/tipo
de alimentación eléctrica indicada en el mismo. La alimentación eléctrica de este
equipo debe provenir de un sistema de distribución general con conductor neutro
a tierra. La tercera pata (puesta a tierra) es una medida de seguridad, no puentearia
ni eliminaria.
Desconexión de alimentación eléctrica • Para desconectar con seguridad la acometida
de alimentación eléctrica al equipo, desenchufar todos los cables de alimentación
en el panel trasero del equipo, o desenchufar el módulo de alimentación (si fuera
independiente), o desenchufar el cable del receptáculo de la pared.
Protección del cables de alimentación • Los cables de alimentación eléctrica se deben
instalar en lugares donde no sean pisados ni apretados por objetos que se puedan
apoyar sobre ellos.
Reparaciones/mantenimiento • Solicitar siempre los servicios técnicos de personal
calificado. En el interior no hay partes a las que el usuario deba acceder. Para evitar
riesgo de electrocución, no intentar personalmente la reparación/mantenimiento
de este equipo, ya que al abrir o extraer las tapas puede quedar expuesto a voltajes
peligrosos u otros riesgos.
Ranuras y aberturas • Si el equipo posee ranuras o orificios en su caja/alojamiento,
es para evitar el sobrecalientamiento de componentes internos sensibles. Estas
aberturas nunca se deben obstruir con otros objetos.
Batería de litio • Existe riesgo de explosión si esta batería se coloca en la posición
incorrecta. Cambiar esta batería únicamente con el mismo tipo (o su equivalente)
recomendado por el fabricante. Desachar las baterías usadas siguiendo las
instrucciones del fabricante.
ᅝܼ乏ⶹsЁ᭛
䄺ਞ
䖭Ͼヺোᦤ⼎⫼᠋䆹䆒໛⫼᠋᠟‫ݠ‬Ё
᳝䞡㽕ⱘ᪡԰੠㓈ᡸ䇈ᯢDŽ
䖭Ͼヺো䄺ਞ⫼᠋䆹䆒໛ᴎ໇‫ݙ‬᳝ᲈ
䴆ⱘॅ䰽⬉य़ˈ᳝㾺⬉ॅ䰽DŽ
⊼ᛣ
䯙䇏䇈ᯢкs䑩ㅸỀ䑩嬦嫿⡈↎⼆枼敆嬼⶷䍇夤ㆁ
㙊⫊₩⏍Ề䑩嬵㕏ɿ
ֱᄬ䇈ᯢкs䑩ㅸⷕ἞⪙⫊₩嬵㕏ᶧḦ⡈⭇㚦Ề
䑩ɿ
䙉ᅜ䄺ਞs䑩ㅸⷕ徶⫉ᷨ␂⏍䑩ㅸ㉈⊘ᵋ䗅ㆁ㙊⫊
₩⏍㐎ẝ嬵㕏ɿ
䙓‫ܡ‬䗑ࡴsᵎ壂Ề䑩嬦ᷨ␂⋃⒇㯢㙊㋩劑䗅⴦₸ㅗ
弾⇡嫿⡈澤Ḧ忀₎⊲斪ɿ
⬉⑤s嬦嫿⡈⌫倾Ề䑩ᷨ␂ᵋ㝈㕏䗅䑶㷑ɿ嫿⡈⼆枼Ề䑩
㙊♱一䗅Ờ䑶䰼丠Ờ䑶ɿ䩭ᵊ㚢一澠♱一澡㕰⫊₩嫿
㓾澤ᵎ倾ᵎ䑩ㅗ崴弈ɿ
ᢨᥝ⬉⑤sᵻ⫊₩♱ḏ嫿⡈㈕㋊䑶㷑澤嬸㈕㋊ㆁ㙊嫿⡈⍏
ㅗ㞍暣䑶㷑䗅䑶㷑一澤ㅗḼẖ㋦ⅱⵃ䑶䰼丠䗅䑶㷑一ɿ
⬉⑤㒓ֱᡸs⣦Ⓟⵄ一澤忀₎埬嵪嵐澤ㅗ愎䆪㉥⋌ɿ
㓈ᡸsㆁ㙊丵Ἧ⼆枼䑲嫥嬂䗅丵Ἧ᷻⎙弜垍ɿ嫿⡈⃆怩㯢
㙊䑩ㅸ⌰Ḧ㘵㊣䗅昷ḷɿᵻ忀₎℻䋱大䑶⊲斪ᵎ壂儫ⴲ
嬖☿㆔⹁嫿⡈䘗⪑丵Ἧ嬦嫿⡈ɿ
䗮亢ᄨs㙊ᷜ嫿⡈㙻⠴ᵋ㙊彛栏㤾ㅗ⪕澤⫄ḭ㕰䑩㚦敳㪣
㙻⃆㒐だ₄ḷ弈䀮ɿᵎ壂䑩Ḽẖᵝ壀㉢Ẑ彛栏⪕ɿ
䫖⬉∴sᵎ㪤䞯䗅㘵㊣䑶㮡ṛ㙊䅇㿹䗅⊲斪ɿ⼆枼Ề䑩ᵏ
⋃⫷㋩劑䗅䘹⍍ㅗ䘹弒⛌⌸䗅䑶㮡ɿ㉊䂨䑠ᷨ⋃䗅⸻
嫯⡅䍇ⷠ⹄䑶㮡ɿ
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. The Class A limits are designed to
provide reasonable protection against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference, in which case the user will be required to correct the interference at his
own expense.
N
This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used
with the unit to ensure compliance with FCC emissions limits.
VSW 2VGA A • Table of Contents
1
Table of Contents
Chapter One • Introduction ................................................... 1-1
About this Manual..................................................................... 1-2
About the VSW 2VGA A........................................................... 1-2
Daisy Chaining the VSW 2VGA A.......................................... 1-3
Features......................................................................................... 1-4
Chapter Two • Installation and Operation .................. 2-1
Installation Overview. .............................................................. 2-2
Mounting the VSW 2VGA A. .................................................. 2-2
Rack shelf mounting............................................................... 2-3
UL rack mounting guidelines..................................................2-3
Rack mounting instructions....................................................2-3
Under-desk mounting............................................................. 2-6
Through-desk mounting......................................................... 2-6
Front Panel Features.................................................................. 2-8
Rear Panel Features................................................................... 2-9
Setting the VSW 2VGA A Jumpers....................................... 2-10
Power connection................................................................. 2-13
Operation.................................................................................... 2-14
Input selection...................................................................... 2-14
Using the VSW I AAP............................................................ 2-14
Setting the VSW I AAP jumpers...........................................2-14
Single switcher example.......................................................2-14
Daisy chain configuration.................................................... 2-15
Loop configuration................................................................2-15
Loop configuration example................................................2-16
Tree configuration.................................................................2-18
Tree configuration example..................................................2-18
Appendix A • Specifications, Part Numbers, and
Accessories .........................................................................................A-1
Specifications...............................................................................A-2
Included Parts..............................................................................A-5
Accessories. ..................................................................................A-5
All trademarks mentioned in this manual are the properties of their respective owners.
VSW 2VGA A • Table of Contents
i
Table of Contents, cont’d
ii
VSW 2VGA A • Table of Contents
VSW 2VGA A
1
Chapter One
Introduction
About this Manual
About the VSW 2VGA A
Daisy Chaining the VSW 2VGA A
Features
Introduction
About this Manual
This manual contains information about the Extron
VSW 2VGA A switcher. The terms “VSW 2VGA A” and
“switcher” are used interchangeably in this manual. The Extron
VSW I AAP interface (part # 70-529-xx), an optional accessory
used when several VSW 2VGA A switchers are daisy chained
together, is also discussed.
About the VSW 2VGA A
The Extron VSW 2VGA A is a compact and economical twoinput, one-output VGA switcher with unbalanced stereo
audio and 300 MHz (-3 dB) video bandwidth. It accepts two
VGA-QXGA, RGBHV, RGBS, RGsB, RsGsBs, component video,
or HDTV component video inputs. The switcher has two
unbalanced stereo audio inputs and one unbalanced stereo
audio output. It also features a buffered local monitor output
for Input 1.
A front panel toggle switch, a contact closure controller, or the
autoswitching option can be used for input selection.
1-2
VSW 2VGA A • Introduction
Daisy Chaining the VSW 2VGA A
Up to ten VSW 2VGA A switchers can be daisy chained together
with each switcher's input separately fed and controlled by an
optional accessory interface, the VSW I AAP (part #70-529-xx).
Figure 1-1 is an example of how several such switcher-interface
combinations can be daisy chained together in a boardroom
environment.
Extron
VSW 1 AAP
Extron
VSW 2VGA A
VGA Switcher
SHOW ME
COMPUTER
AUDIO
VSW I AAP
Extron
VSW I AAP
Expandable, economical presentation chain for
conference rooms and library study rooms.
Extron’s pre-made
VGA with audio cable
assemblies.
SHOW ME
COMPUTER
AUDIO
SHOW ME
VSW I AAP
COMPUTER
VSW I
AAP
AUDIO
INPUT 1
INPUT 2
1
2
In 2
VSW I AAP
COMPUTER
VSW I
AAP
In 1
INPUT 1
1
2
Out
In 2
INPUT 1
VSW 2VGA A
INPUT 2
1
2
VSW 2VGA A
VSW 2VGA A
Out
In 2
In 1
INPUT 1
INPUT 2
1
2
VSW 2VGA A
VSW 2VGA A
VSW I AAP
VSW I
AAP
In 1
INPUT 2
Projector
SHOW ME
AUDIO
Out
VSW 2VGA A
VSW 2VGA A
Extron’s pre-made VGA with audio cable assemblies.
Figure 1-1 — Daisy chaining the multiple switchers
By default, all switchers are set to input 2 as the active input;
therefore, in a daisy chain of switchers the VGA and audio
signals flow from one switcher to input 2 of the next switcher in
the chain. The switchers are daisy chained in this fashion until
the last switcher in the daisy chain outputs to a projector and
audio amplifier.
Up to ten switchers can be daisy chained together without any
degradation in picture quality. One power supply powers up to
five switchers.
VSW 2VGA A • Introduction
1-3
Introduction, cont’d
Features
Autoswitching ability — The VSW 2VGA A can detect active
sync signals and automatically switch to the highest
numbered active input.
Furniture mountable — The VSW 2VGA A can be mounted
on a rack shelf, under a desk or podium, through a desk
or furniture, or to a projector mount, using optional
hardware.
Daisy chaining — Multiple VSW 2VGA A switchers can be
daisy chained together to form a presentation system.
Each switcher can then be separately controlled through
an Extron VSW I AAP interface.
Stereo audio — Unbalanced stereo audio inputs and outputs on
3.5 mm stereo mini jacks.
1-4
VSW 2VGA A • Introduction
VSW 2VGA A
2
Chapter Two
Installation and Operation
Installation Overview
Mounting the VSW 2VGA A
Front Panel Features
Rear Panel Features
Operation
Installation and Operation
Installation Overview
To install and set up the VSW 2VGA A for operation, follow
these steps:
1 Turn all of the equipment off. Make sure that the video
and audio sources (computers, stereos, tape decks, or other
devices), the VSW 2VGA A, the output devices (projectors,
speakers), and the contact closure control device are all
turned off and disconnected from the power source.
2 If you are going to daisy chain two or more switchers with
VSW I AAP control panels, identify the revision of the
VSW 2VGA A board (for configuring the VSW I AAPs)
and configure the switchers' jumpers. See “Setting the
VSW 2VGA A Jumpers” on page 2-10.
3 If desired, mount the switcher. See “Mounting the
VSW 2VGA A” in this chapter.
4 Attach the cables. See “Front Panel Features" and "Rear
Panel Features" in this chapter.
5 Connect power cords and turn on the devices in the
following order: output devices, contact closure controller,
VSW 2VGA A switcher, and input devices.
6 Select an input using the front panel input toggle switch or
the contact closure controller.
7 The image should now display, and sound should be
audible. If not, ensure that all devices are plugged in and
receiving power. Check the cabling and make adjustments
as needed. Select a different input to check for a picture
and sound.
Mounting the VSW 2VGA A
N If you are going to daisy chain two or more switchers with
VSW I AAP control panels, identify the revision of the
VSW 2VGA A board (for configuring the VSW I AAPs)
and configure the switchers' jumpers before mounting
the switchers. See “Setting the VSW 2VGA A Jumpers”
on page 2-10.
The VSW 2VGA A can be mounted in a rack, or under or
through furniture, using one of the following optional mounting
kits:
2-2
•
RSF 123 3 inch rack shelf kit (part #60-190-20)
•
RSB 123 3 inch rack shelf (part #60-604-20)
VSW 2VGA A • Installation and Operation
•
RSU 126 6 inch deep universal rack shelf kit (part #60190-10)
•
RSB 126 6 inch deep basic rack shelf (part #60-604-10)
•
RSU 129 9 inch 1U universal rack shelf kit (part #60-19001)
•
RSB 129 9 inch 1U basic rack shelf (part #60-604-01)
•
MBU 125 Under-desk mount kit (part #70-077-01)
•
MBD 129 Through-desk mount kit (part #70-077-02)
When mounting the switcher, take cabling and power
availability into consideration. Follow the appropriate
mounting procedure on the following pages.
Rack shelf mounting
UL rack mounting guidelines
The following Underwriters Laboratories (UL) guidelines
pertain to the safe installation of the VSW 2VGA A in a rack.
1.
Elevated operating ambient temperature — If installed in
a closed or multi-unit rack assembly, the operating ambient
temperature of the rack environment may be greater than
room ambient temperature. Therefore, install the switcher
in an environment compatible with the maximum ambient
temperature (Tma = +122° F, +50° C) specified by Extron.
2.
Reduced air flow — Install the equipment in a rack so that
the amount of air flow required for safe operation of the
equipment is not compromised.
3.
Mechanical loading — Mount the equipment in the rack
so that a hazardous condition is not achieved due to
uneven mechanical loading.
4.
Circuit overloading — Connect the equipment to
the supply circuit and consider the effect that circuit
overloading might have on overcurrent protection and
supply wiring. Appropriate consideration of equipment
nameplate ratings should be used when addressing this
concern.
5.
Reliable earthing (grounding) — Maintain reliable
grounding of rack-mounted equipment. Pay particular
attention to supply connections other than direct
connections to the branch circuit (e.g. use of power strips).
Rack mounting instructions
1. If feet were installed on the bottom of the switcher, remove
them.
VSW 2VGA A • Installation and Operation
2-3
Installation and Operation, cont’d
2.
Mount the VSW 2VGA A on one of the following rack
shelves:
• RSF 123 rack shelf kit (part #60-190-20)
• RSB 123 rack shelf (part #60-604-20)
• RSU 126 6 inch deep universal rack shelf kit
(part #60-190-10)
• RSB 126 6 inch deep basic rack shelf (part #60-604-10)
• RSU 129 1U universal rack shelf kit (part #60-190-01)
• RSB 129 1U basic rack shelf (part #60-604-01)
On the standard rack shelf, the switcher mounts in one
of four locations to the rear of the rack or in one of four
locations to the front of the rack.
3.
Attach the switcher to the rack shelf using two
4-40 x 3/16 inch machine screws. Insert the screws from
the underside of the shelf and securely fasten them into
diagonally opposite corners, as shown in figure 2-1.
VersaTools Rack Shelf
1/4 Rack Width Front
False Faceplate
Use 2 mounting holes on
opposite corners.
(2) 4-40 x 3/16"
Screws
Figure 2-1 — Mounting the VSW 2VGA A on a rack
shelf
N Since the switcher is 1.0 inch high, there will be a gap of
0.75 inch above the switcher.
2-4
VSW 2VGA A • Installation and Operation
4.
Attach the rack shelf to the rack using four
10-32 x 3/4 inch bolts (provided). Insert the bolts through
#10 beveled washers, then through the holes in the rack
ears and rack, as shown in figure 2-2.
1U Universal Rack Shelf
Use 2 mounting holes on
opposite corners.
(2) 4-40 x 3/16"
Screws
Figure 2-2 — Mounting the VSW 2VGA A on a
standard 1U rack shelf
VSW 2VGA A • Installation and Operation
2-5
Installation and Operation, cont’d
Under-desk mounting
1.
Attach the under-desk mounting brackets (MBU 125,
part #70-077-01) to the VSW 2VGA A with the four
provided machine screws, as shown in figure 2-3.
Figure 2-3 — Under-desk mounting brackets
2.
Hold the switcher with attached brackets against the
mounting surface. Use a soft pencil to mark the location of
holes for screws on the desk or other furniture.
3.
Drill 1/4 inch (6.4 mm) deep, 3/32 inch (2 mm) diameter
pilot holes in the table or desk at the marked screw
locations from the underside/inside (concealed side) of the
furniture, where the switcher will be located.
4.
Attach the VSW 2VGA A to the desk with the provided
wood screws.
Through-desk mounting
2-6
1.
Hold the front panel of the switcher against the furniture.
Use a soft pencil to mark the rough-in opening on the desk.
The opening, 1.125 inch x 4.425 inch (2.8 cm x 11.2 cm) will
be slightly larger than the switcher enclosure.
2.
Cut out the material from the rough-in area with a jigsaw.
Check the opening size by inserting the switcher part way
through the hole. If needed, use a saw, file, or sandpaper
to enlarge the hole. Smooth the edges of the hole with
sandpaper.
VSW 2VGA A • Installation and Operation
Attach the through-desk mounting brackets
(MBD 129, part #70-077-02) to the VSW 2VGA A with the
four provided machine screws, as shown in the throughdesk mounting diagram on the next page.
4.
Hold the switcher with attached brackets up against the
underside of the desk or table. Use a soft pencil to mark
the locations of the holes for the screws that will attach the
brackets to the desk.
5.
Drill 1/4 inch (6 mm) deep, 3/32 inch (2 mm) diameter
pilot holes in the desk or table at the marked screw
locations. The holes should be drilled from the underside
or inside (concealed side) of the furniture, where the
switcher will be located.
6.
Attach the switcher to the desk or table with the provided
wood screws, as shown in figure 2-4.
1
2
P
IN
T
U
1
IN
T
U
P
2
S
V
W
2V
G
A
A
3.
Figure 2-4 — Through-desk mounting
7.
To adjust the height of the switcher within the desk,
slightly loosen the screws that attach the brackets to the
switcher, adjust the height by sliding the switcher up or
down, and retighten the screws.
VSW 2VGA A • Installation and Operation
2-7
Installation and Operation, cont’d
Front Panel Features
INPUT 1
1
2
INPUT 2
1
2
VSW 2VGA A
3
4
5
6
7
Figure 2-5 — VSW 2VGA A front panel features
a
b
Input 1 LED indicator — This LED lights green whenever
input 1 (video and audio) is selected.
Input 2 LED indicator — This LED lights green whenever
input 2 (video and audio) is selected.
N The LEDs a and b above also serve as power up
indicators. When the switcher is powered up, the selected
input's LED lights green.
c
d
e
Input select toggle switch — Toggling this switch up selects
input 1; toggling it down selects input 2.
Input 1 video — Input VGA-QXGA, RGBHV, RGBS, RGsB,
RsGsBs, component video, or HDTV component video through
this female 15-pin HD connector.
Input 1 audio — Input unbalanced stereo audio through this
3.5 mm mini audio jack (figure 2-6).
Tip (L)
Ring (R)
Sleeve ( )
3.5 mm Stereo Plug Connector
(unbalanced)
Figure 2-6 — Audio input connector
f
g
2-8
Input 2 video — Input VGA-QXGA, RGBHV, RGBS, RGsB,
RsGsBs, component video, or HDTV component video through
this female 15-pin HD connector.
Input 2 audio — Input unbalanced stereo audio through this
3.5 mm mini audio jack. See figure 2-6.
VSW 2VGA A • Installation and Operation
Rear Panel Features
POWER
12V
.1A MAX
VGA IN 1 LOOP
OUTPUT
VSW 2VGA A
AUD OUT
CONTACT
1
2
AUTO-SW
1
2
3
4
5
Figure 2-7 — VSW 2VGA A rear panel features
a
Power connector — Connect the included 12 VDC external
power supply to the 2-pole, 3.5 mm captive screw connector.
N One power supply can power up to five switchers.
b
c
d
See "Power connection" in this chapter.
Loop Thru Input 1 connector — female 15-pin HD connector for
buffered local monitor output from Input 1
Output — female 15-pin HD connector for output from Input
1 or Input 2. The output video type follows input type and is
either VGA-QXGA, RGBHV, RGBS, RGsB, RsGsBs, component
video, or HDTV component video.
Audio Output connector — Unbalanced stereo audio is output
from this 3.5 mm mini audio jack (figure 2-8).
Tip (L)
Ring (R)
Sleeve ( )
3.5 mm Stereo Plug Connector
(unbalanced)
Figure 2-8 — Audio output connector
N If you are daisy chaining, connect the other end of
the audio cable to the audio Input 2 connector on the
downstream switcher.
e
Contact closure/Autoswitching (Contact/Auto-SW) —
Contact closure — Connect a contact closure device to this
3-pole, 3.5 mm captive screw connector.
•
Pin 1 selects Input 1 when momentarily connected to
ground (pin 3).
VSW 2VGA A • Installation and Operation
2-9
Installation and Operation, cont’d
•
Pin 2 selects Input 2 when momentarily connected to
ground (pin 3).
•
Ground connects to the ground wire (equipment
ground).
1 2
N Simultaneously connecting both pins 1 and 2 to
ground (pin 3) turns autoswitching mode on.
Autoswitching —
N Autoswitch mode must be disabled when daisy chaining
VSW 2VGA A switchers. If the autoswitch mode is
enabled, the switchers cannot be daisy chained.
N RGsB and RsGsBs inputs and outputs occur in manual
mode only.
N Autoswitching requires TTL level sync on pin 13 of the
15-pin HD connector.
Pins 1, 2, and Ground when jumpered/shorted together (as
shown at right) turn the autoswitching mode on. When
CONTACT
the autoswitching mode is on, the switcher automatically 1 2
switches to the input that has an active sync signal.
If both inputs have an active sync signal present, input
2 is selected, and the input 2 LED indicator lights. If no active
sync signal is present, the input 1 LED indicator still lights to
indicate that the unit is still powered on.
N When the autoswitch mode is active, both daisy chaining
and the front panel's input toggle switch are disabled,
and the input cannot be manually switched. Any attempt
to toggle the switch while the switcher is in this mode
results in the flashing of the currently active input's
LED indicator. Contact closure is also disabled while in
autoswitch mode.
Setting the VSW 2VGA A Jumpers
N If you plan to use the VSW I AAP and/or create a daisy
chain configuration, you must configure the switchers
before installing them in a rack or furniture and making
connections.
Daisy chaining VSW 2VGA A switchers requires you to check
and/or set internal jumpers in the switcher.
1.
2-10
If applicable, disconnect all power to the switcher and any
attached devices.
VSW 2VGA A • Installation and Operation
2.
Remove the two screws on each side of the switcher
(figure 2-9). Remove the four connector nuts on the front
panel of the switcher. Lift the top cover off of the switcher.
UT
INP
2
GA
W
UT
INP
Remove (4)
Screws
1
VS
A
2V
1
2
Remove (4)
Connector Nuts
Figure 2-9 — Removing the cover
FRONT PANEL
JMP1
JMP3
EXTRON 20-881-nn x
ER:- yyyyyyyy yyyy
JMP4
JMP5
JMP6
Figure 2-10 — VSW 2VGA A jumper locations
3.
Set the jumpers for the switcher. See figure 2-11.
4.
Set the cover in place and resinstall the screws remove in
step 2.
There are five jumpers, numbered JMP1, and JMP3 thru JMP6,
that control daisy chaining on the VSW 2VGA A switcher (figure
2-10). Both data and power must be daisy chained from one
switcher to another.
VSW 2VGA A • Installation and Operation
2-11
Installation and Operation, cont’d
OPEN
CLOSED
All jumpers are set open (disabled) by default.
Open or close the indicated jumpers in the table below,
as needed, to adjust the appropriate settings. See “Using
the VSW I AAP” and “Daisy chain configuration” in this
chapter for other jumper settings.
Pin 5 - Control
Pin 9 - +5 VDC
Input 1
JMP 1
Input 2
JMP 3
JMP 4
Output
JMP 5
JMP 6
Figure 2-11 — Jumper positions
These jumpers enable or disable VGA connector pin 5 (control)
and VGA connector pin 9 (power) of the switcher inputs and
outputs. Close (install) the jumper for VGA connector pin 5
to daisy chain data to the next switcher, and close (install) the
jumper for VGA connector pin 9 to daisy chain power to the
next switcher.
N When the switchers are not daisy chained together or used
with the VSW I AAP, all jumpers should be in the default
(open) position.
2-12
VSW 2VGA A • Installation and Operation
Power connection
One power supply can power up to five daisy chained
switchers. Additional switchers require one or more power
supplies. See "Daisy chain configuration", later in this chapter.
Figure 2-12 shows how to wire the power connector.
Smooth
Ridges
A
A
SECTION A–A
3/16” (5 mm) Max.
Power Supply
Output Cord
(to ground)
Captive Screw
Connector
Figure 2-12 — Power connector wiring
C
The two power cord wires must be kept separate
while the power supply is plugged in. Remove
power before wiring.
C
When you are connecting the power supply, voltage
polarity is critical. Applying power with incorrect
voltage polarity could damage the power supply
and the VSW 2VGA A. Identify the power cord
negative (ground) lead by the ridges on the side of
the cord or a black heat shrink wrapping around it.
N Strip the jacket to expose 3/16 inch (5 mm) of the
conductors. Do not tin the stripped power supply leads
before installing the captive screw connector. Tinned wires
are not as secure in the captive screw connectors and could
be pulled out.
To verify the polarity before connection, check the no load
power supply output with a voltmeter.
N The maximum number of switchers that can be daisy
chained is limited by several factors: power consumption,
cable lengths, and the overall distortion of the video and
audio signals.
VSW 2VGA A • Installation and Operation
2-13
Installation and Operation, cont’d
Operation
Apply power and the input signals. The video and audio
output connectors, including the Loop Thru Input 1 connector,
should output signals.
Input selection
There are three ways to select between Input 1 and Input 2:
•
Toggle the front panel input select switch up (Input 1) or
down (Input 2).
•
Use the rear panel contact closure capability.
•
Press the Show Me button on the VSW I AAP to select the
input on the connected VSW 2VGA A switcher.
Using the VSW I AAP
The VSW I AAP can be used on the inputs of a single switcher
or on the inputs of multiple switchers in a daisy chain
configuration.
Setting the VSW I AAP jumpers
A jumper on the VSW I AAP may need to be shifted from
jumper J6 (the default position) to J5, depending on the
application. See the following illustration and table.
J5 J6
Jumper installed
Switcher compatibility
J6
VSW 2VGA A (Input 1)
J5
VSW 2VGA A (Input 2)
Single switcher example
The following illustration is an example of a single switcher
configuration.
2-14
VSW 2VGA A • Installation and Operation
SHOW ME
1
2
VSW I AAP
VSW I AAP
VSW I AAP
SHOW ME
COMPUTER
AUDIO
SHOW ME
VSW I AAP
COMPUTER
AUDIO
VSW I AAP
Out
Internal Jumper Settings
Input 1
Input 2
INPUT 1
INPUT 2
1
2
VSW 2VGA A
12 V Power
Supply*
VSW 2VGA A
Out
Jumper
Setting
JMP1
Closed
JMP3
Closed
JMP4
Closed
JMP5
Open
JMP6
Open
Figure 2-13 — Single switcher configuration
Press the ShowProjector
Me button on the VSW I AAP to select the
corresponding input on the VSW 2VGA A.
Daisy chain configuration
Multiple VSW 2VGA A switchers can be daisy chained together
in a loop configuration or a tree comfiguration.
N Daisy chaining uses all pins and wires of a standard VGA
cable. Not all VGA cables include all pins and wires.
Ensure that the VGA cable that you use has all 15 pins
connected.
Loop configuration
In a loop configuration, the output of each VSW 2VGA A is
connected to Input 2 of the next VSW 2VGA A switcher. This
repetition of one switcher's output to another switcher's input
can be repeated for up to a maximum of 10 switchers in a daisy
chain. The output of the first switcher is connected to a display.
Source signals are connected to Input 1 of each VSW 2VGA A
switcher either directly or through the VSW I AAP interface.
Select the source by toggling to Input 1 on the VSW 2VGA
A's front panel (or through contact closure on the rear panel)
or by pressing the VSW I AAP's Show Me button for the
corresponding switcher.
•
Up to 10 switchers can be daisy chained in this
configuration without any signal degradation.
•
A power supply is required for every 5 switchers.
VSW 2VGA A • Installation and Operation
2-15
Installation and Operation, cont’d
•
Configure the jumpers on each VSW 2VGA A according to
the following example.
•
The VSW I AAP is configured for a loop configuration by
default.
N In a loop configuration, the "show me" feature can be used
without a VSW I AAP control panel. Select Input 1 using
either the front panel toggle switch (see item c in "Front
Panel Features") or the rear panel contact closure control
(see item e in "Rear Panel Features") to issue the "show
me" control signal.
Loop configuration example
The illustration on the following page is an example of daisy
chaining using a loop configuration.
2-16
VSW 2VGA A • Installation and Operation
Figure 2-14 — Loop configuration
VSW 2VGA A • Installation and Operation
2-17
SHOW ME
VSW I AAP
VSW 2VGA A
INPUT 2
SHOW ME
VSW I AAP
INPUT 1
In 1
AUDIO
VSW 2VGA A
INPUT 2
VSW 2VGA A
INPUT 2
SHOW ME
VSW I AAP
INPUT 1
In 1
AUDIO
VSW 2VGA A
INPUT 2
VSW 2VGA A
INPUT 2
SHOW ME
VSW I AAP
INPUT 1
In 1
AUDIO
VSW 2VGA A
INPUT 2
VSW 2VGA A
INPUT 2
INPUT 1
In 1
AUDIO
SHOW ME
VSW I AAP
VSW 2VGA A
INPUT 2
In 1
VSW 2VGA A
INPUT 2
INPUT 1
In 1
AUDIO
SHOW ME
VSW 2VGA A
INPUT 2
VSW I AAP
JMP6
JMP6
JMP6
Table 1
Closed
Open
JMP5
Closed
Closed
JMP5
Closed
Closed
JMP5
Table 2
Closed
Closed
JMP4
Closed
JMP4
Open
JMP4
Table 3
Closed
JMP3
Closed
JMP3
1
VSW 2VGA A
1
2
COMPUTER
VSW I AAP
6
Closed
In 2
INPUT 1
VSW 2VGA A
1
2
SHOW ME
VSW I AAP
JMP3
Out
In 2
AUDIO
Setting
2
VSW 2VGA A
1
2
COMPUTER
VSW I AAP
7
Out
COMPUTER
VSW I AAP
JMP1
In 2
In 1
INPUT 1
VSW 2VGA A
1
2
SHOW ME
VSW I AAP
Jumper
Out
12V Power
Supply
In 2
AUDIO
Closed
3
VSW 2VGA A
1
2
COMPUTER
VSW I AAP
8
Out
COMPUTER
VSW I AAP
Setting
In 2
In 1
INPUT 1
VSW 2VGA A
1
2
SHOW ME
VSW I AAP
JMP1
Out
In 2
AUDIO
Jumper
4
VSW 2VGA A
1
2
COMPUTER
VSW I AAP
9
Out
COMPUTER
VSW I AAP
Closed
In 2
In 1
INPUT 1
VSW 2VGA A
1
2
SHOW ME
VSW I AAP
Setting
Out
In 2
AUDIO
JMP1
5
VSW 2VGA A
1
2
COMPUTER
VSW I AAP
10
Out
COMPUTER
VSW I AAP
Jumper
In 2
INPUT 1
In 1
AUDIO
VSW 2VGA A
1
2
COMPUTER
VSW I AAP
12V Power
Supply
Out
Projector
Out
Installation and Operation, cont’d
Tree configuration
In a tree configuration, the output of each VSW 2VGA A
switcher is connected to input 1 or input 2 of the next switcher.
This repetition of one switcher's output to another switcher's
input can be repeated for up to a maximum of 10 switchers in
a daisy chain. The output of the last switcher is connected to a
display.
Source signals are connected to input 1 and input 2 of each VSW
2VGA A switcher at the top of the tree through a VSW I AAP
interface. Select the source by pressing the VSW I AAP's Show
Me button for the corresponding switcher.
•
Switchers can be daisy chained in this configuration up to
ten levels deep without any signal degradation.
•
A power supply is required for each switcher in the
chain that has its output connected to input 1 of the next
switcher.
•
Sources can only be selected and connected to the
switcher through the VSW I AAP interface.
•
Each VSW I AAP must be configured for the tree
configuration. See "Using the VSW I AAP" in this chapter
for additional information.
Tree configuration example
The following illustration is a simple example of daisy chaining
using a tree configuration.
2-18
VSW 2VGA A • Installation and Operation
1
2
VSW I AAP
VSW I AAP
3
SHOW ME
AUDIO
COMPUTER
4
VSW I AAP
SHOW ME
VSW I AAP
AUDIO
COMPUTER
VSW I AAP
SHOW ME
VSW I AAP
AUDIO
COMPUTER
Out
COMPUTER
AUDIO
VSW I AAP
Out
Input 1
Input 1
B
SHOW ME
VSW I AAP
Input 2
Input 2
INPUT 1
INPUT 1
INPUT 2
1
2
INPUT 2
1
2
VSW 2VGA A
VSW 2VGA A
B
Out
12 V Power
Supply*
Input 1
Input 2
INPUT 1
INPUT 2
A
1
2
VSW 2VGA A
VSW 2VGA A
Out
12 V Power
Supply
* Every switcher connected
to Input 1 of another
switcher must have its
own power supply.
Projector
Internal Jumper Settings
A
B
Jumper
Setting
Jumper
JMP1
Closed
JMP1
Closed
JMP3
Closed
JMP3
Closed
JMP4
Closed
JMP4
Closed
JMP5
Closed
JMP5
Open
JMP6
Closed
JMP6
Open
Setting
Figure 2-15 — Tree configuration
VSW 2VGA A • Installation and Operation
2-19
Installation and Operation, cont’d
2-20
VSW 2VGA A • Installation and Operation
VSW 2VGA A
A
Appendix A
Specifications, Part Numbers,
and Accessories
Specifications
Included Parts
Accessories
Specifications, Part Numbers, and Accessories
Specifications
Video
Gain������������������������������������������������� Unity
Bandwidth�������������������������������������� 300 MHz (-3 dB)
Video input and loop through
Number/signal type��������������������� 2 VGA-QXGA RGBHV, RGBS, RGsB*,
RsGsBs*, HDTV component video* input
1 VGA-QXGA RGBHV, RGBS, RGsB,
RsGsBs, HDTV component video* local
monitor loop-through
N
RGsB, RsGsBs, and HDTV component video inputs and
outputs work in manual mode only. Autoswitching requires
TTL level sync on pin 13 of the 15-pin HD connector.
Connectors������������������������������������� 3 female 15-pin HD
Pin connections������������������������������ ID bits on pins 4, 11, 12, 15 from inputs 1
and 2: passed to main output
Pin 9 of input 1: floating
Pin 9 of input 2: used for the Show-Me
feature
Nominal level�������������������������������� 1.0 Vp-p for Y of component video
0.7 Vp-p for RGB and for R-Y and B-Y of
component video
Minimum/maximum levels�������� Analog: 0.4 V to 1.8 Vp-p with no offset
Impedance�������������������������������������� 75 ohms
Horizontal frequency�������������������� 15 kHz to 145 kHz
Vertical frequency�������������������������� 30 Hz to 170 Hz
Video output
Number/signal type��������������������� 1 VGA-QXGA RGBHV, RGBS, RGsB*,
RsGsBs*, HDTV component video*
(follows input type)
Connectors������������������������������������� 1 female 15-pin HD
Nominal level�������������������������������� 1.0 Vp-p for Y of component video
0.7 Vp-p for RGB and for R-Y and B-Y of
component video
Minimum/maximum levels�������� 0.4 V to 1.8 Vp-p (follows input)
Impedance�������������������������������������� 75 ohms
N
A-2
ID bits are passed through from VGA inputs to the VGA output.
VSW 2VGA A • Specifications, Part Numbers, and Accessories
Sync
Input type��������������������������������������� RGBHV, RGBS, RGsB*, RsGsBs*, bi-level
and tri-level (HDTV) component video
sync
Output type������������������������������������ RGBHV, RGBS, RGsB*, RsGsBs*, bi-level
and tri-level (HDTV) component video
sync (follows input)
Input level�������������������������������������� 1.8 V to 5.0 Vp-p
Output level����������������������������������� TTL: 5.0 V p-p, unterminated
Input impedance��������������������������� 510 ohms
Output impedance������������������������ 50 ohms
Max. input voltage������������������������ 5.0 Vp-p
Max. rise/fall time������������������������ 40 ns
Polarity������������������������������������������� Positive or negative (follows input)
Audio
Gain������������������������������������������������� Unbalanced output: 0 dB
Frequency response���������������������� 20 Hz to 20 kHz, ±0.05 dB
THD + Noise���������������������������������� 0.002% @ 1 kHz at nominal level (-10 dBV)
S/N�������������������������������������������������� 94 dB at maximum output (unweighted)
Crosstalk����������������������������������������� -50 dB @ 20 kHz, -75 dB @ 1 kHz and
below 60 Hz
Stereo channel separation������������ 96 dB @ 1 kHz
Audio input
Number/signal type��������������������� 2 stereo, unbalanced
Connectors������������������������������������� (2) 3.5 mm mini audio jacks (tip, ring,
sleeve)
Impedance�������������������������������������� 22k ohms unbalanced, AC coupled
Nominal level�������������������������������� -10 dBV (316 mVrms)
Maximum level������������������������������ +9 dBV, (unbalanced) at 1% THD+N
N
0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu
Audio output
Number/signal type��������������������� 1 stereo, unbalanced
Connectors������������������������������������� (1) 3.5 mm mini audio jack (tip, ring,
sleeve)
VSW 2VGA A • Specifications, Part Numbers, and Accessories
A-3
Specifications, Part Numbers, and Accessories
Impedance�������������������������������������� 50 ohms unbalanced
Gain error��������������������������������������� ±0.1 dB channel to channel
Maximum level (Hi-Z)����������������� >+9 dBV, unbalanced at 1% THD+N
Maximum level (600 ohm)����������� >+7 dBV, unbalanced at 1% THD+N
Control/remote — switcher
Contact closure������������������������������ (1) 3.5 mm captive screw connector, 3 pole
for momentary contact
Contact closure pin configurations� 1 = input 1 select, 2 = input 2 select, 3 =
GND
Shorting all three pins together enables
autoswitch mode.
Loop signal������������������������������������� Momentary low, 250 µs
General
External power supply����������������� 100 VAC to 240 VAC, 50-60 Hz, external; to
12 VDC, 1 A (max.), regulated
Power input requirements����������� 12 VDC, 0.1 A
Temperature/humidity���������������� Storage: -40 to +158 °F (-40 to +70 °C) /
10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) /
10% to 90%, noncondensing
Cooling������������������������������������������� Convection, no vents
Mounting
Rack mount������������������������ Yes, with optional 1U rack shelf
Furniture mount���������������� Yes, with optional under-desk mounting
kit or through-desk mounting kit
Pole mount������������������������� Yes, with optional pole mount kit
Enclosure type������������������������������� Metal
Enclosure dimensions������������������� 1.0" H x 4.3" W x 3.0" D (quarter rack
wide)
2.5 cm H x 10.9 cm W x 7.6 cm D
(Depth excludes connectors.)
Product weight������������������������������ 0.5 lb (0.3 kg)
Shipping weight���������������������������� 3 lbs (2 kg)
Vibration����������������������������������������� ISTA 1A in carton (International Safe
Transit Association)
Regulatory compliance
Listings������������������������������� CE, c-UL, UL
Compliances����������������������� CE, C-tick, FCC Class A, ICES, VCCI
A-4
VSW 2VGA A • Specifications, Part Numbers, and Accessories
MTBF����������������������������������������������� 30,000 hours
Warranty����������������������������������������� 3 years parts and labor
N
All nominal levels are at ±10%.
N
Specifications are subject to change without notice.
Included Parts
These items are included in each order for a VSW 2VGA A:
Included parts
Part number
to reorder
VSW 2VGA A
60-758-01
12 VDC, 1A external power supply
70-775-01
3.5 mm 3-pole captive screw connector
3.5 mm 2-pole captive screw connector
VSW 2VGA A Setup Guide
Accessories
Accessories
Part number
VSW I AAP — black
70-529-11
VSW I AAP — white
70-529-21
VSW I AAP — RAL9010 white
70-529-51
RSB 123 —
1U basic rack shelf
60-604-21
RSF 123 —
1U rack shelf kit
60-190-20
RSU 126 —
1U 6" deep universal rack shelf kit
60-190-10
RSB 126 — 1U 6" deep basic rack shelf
60-604-11
RSU 129 — 1U universal rack shelf kit
60-190-01
RSB 129 — 1U basic rack shelf
60-604-02
MBU 125 — 1U under-desk mount kit
70-077-01
MBD 129 — 1U through-desk mount kit
70-077-02
VSW 2VGA A • Specifications, Part Numbers, and Accessories
A-5
Specifications, Part Numbers, Accessories, cont’d
A-6
Cable Accessories
Part number
VGA with audio cables
26-490-xx
VGA to BNC-5 female cables
(SY VGA), 0.5' - 100' (0.15 m - 30.4 m)
26-531-xx
VGA to BNC-5 male cables
(SY VGA), 0.5' - 100' (0.15 m - 30.4 m)
26-533-xx
MSR 6 Adapter, 6" (0.15 m)
26-592-01
3.5 mm Mini Stereo-HQ/10
100-331-01
VSW 2VGA A • Specifications, Part Numbers, and Accessories
VSW 2VGA A • Specifications, Part Numbers, and Accessories
A-7
Specifications, Part Numbers, Accessories, cont’d
A-8
VSW 2VGA A • Specifications, Part Numbers, and Accessories
Extron Warranty
Extron Electronics warrants this product against defects in materials and workmanship
for a period of three years from the date of purchase. In the event of malfunction during
the warranty period attributable directly to faulty workmanship and/or materials,
Extron Electronics will, at its option, repair or replace said products or components,
to whatever extent it shall deem necessary to restore said product to proper operating
condition, provided that it is returned within the warranty period, with proof of
purchase and description of malfunction to:
USA, Canada, South America,
and Central America:
Extron USA
1001 East Ball Road
Anaheim, CA 92805
U.S.A.
Europe, Africa, and the Middle East:
Extron Europe
Hanzeboulevard 10
3825 PH Amersfoort
The Netherlands
Asia:
Extron Asia
135 Joo Seng Road #04-01
PM Industrial Bldg.
Singapore 368363
Singapore
Japan:
Extron Japan
Kyodo Building, 16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
China:
Extron China
686 Ronghua Road
Songjiang District
Shanghai 201611
China
Middle East:
Extron Middle East
Dubai Airport Free Zone
F12, PO Box 293666
United Arab Emirates, Dubai
This Limited Warranty does not apply if the fault has been caused by misuse, improper
handling care, electrical or mechanical abuse, abnormal operating conditions or nonExtron authorized modification to the product.
If it has been determined that the product is defective, please call Extron and ask for an
Applications Engineer at (714) 491-1500 (USA), 31.33.453.4040 (Europe), 65.6383.4400
(Asia), or 81.3.3511.7655 (Japan) to receive an RA# (Return Authorization number). This
will begin the repair process as quickly as possible.
Units must be returned insured, with shipping charges prepaid. If not insured, you
assume the risk of loss or damage during shipment. Returned units must include the
serial number and a description of the problem, as well as the name of the person to
contact in case there are any questions.
Extron Electronics makes no further warranties either expressed or implied with respect
to the product and its quality, performance, merchantability, or fitness for any particular
use. In no event will Extron Electronics be liable for direct, indirect, or consequential
damages resulting from any defect in this product even if Extron Electronics has been
advised of such damage.
Please note that laws vary from state to state and country to country, and that some
provisions of this warranty may not apply to you.
Extron USA - West
Headquarters
+800.633.9876
Inside USA / Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron USA - East
Extron Europe
Extron Asia
Extron Japan
Extron China
Extron Middle East
+800.633.9876
+800.3987.6673
+800.7339.8766
+81.3.3511.7655
+81.3.3511.7656 FAX
+400.883.1568
+971.4.2991800
+971.4.2991880 FAX
+1.919.863.1794
+1.919.863.1797 FAX
+31.33.453.4040
+31.33.453.4050 FAX
+65.6383.4400
+65.6383.4664 FAX
Inside USA / Canada Only
Inside Europe Only
Inside Asia Only
© 2009 Extron Electronics. All rights reserved.
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Download PDF