Medion | PC | Instruction manual | Medion PC Instruction manual

i
All-In-One PC
What Your 2 Year Warranty Means
Great care has gone into manufacturing this product and it should therefore provide you
with years of good service when used correctly. In the event of product failure within its
intended use over the course of the two years after the date of purchase, we will rectify the
problem as quickly as possible once it has been brought to our attention. In the unlikely
event of such an occurrence, or if you require any information about the product please
contact us via our after sales support services, details of which can be found in this manual
and on the product itself.
Copyright © 2010
All rights reserved.
This manual is protected by Copyright.
Trademarks:
®
®
®
MS-DOS and Windows are registered trademarks of Microsoft .
®
®
Pentium is a registered trademark of Intel .
Other trademarks are the property of their respective owners.
®
Medion makes no warranty of any kind with regard to this material, including, but
not limited to, the implied warranties of merchantability and fitness for a particular purpose.
®
Medion shall not be liable for errors contained herein or for incidental or consequential damages in
connection with the furnishing, performance, or use of this material.
®
Medion assumes no responsibility for the use or reliability of its software on equipment that is not
®
furnished by Medion .
This document contains proprietary information that is protected by copyright. All rights are reserved.
No part of this document may be photocopied, reproduced, or translated to another language
®
without the prior written consent of Medion .
The information in this document is subject to change without notice.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
ii
Notes on this Manual
Keep these instructions with your computer at all times. The proper set up, use and care
can help extend the life of your computer. In the event that you transfer ownership of this
computer, please provide these instructions to the new owner.
This manual is divided into sections to help you locate the information you require. Along
with the Table of Contents at the beginning of this manual, an Index has been provided to
help you find topical information.
If you want to start up your All-In-One PC immediately, please read the chapters Operational Safety (page 3) and Setting up and Getting Started (page 21).
We strongly recommend you read this entire manual to ensure the proper set-up and
operation of your All-In-One PC.
Many application programs incorporate extensive help functions. As a general rule, you
can access help functions by pressing F1 on the keyboard. These help functions will be
®
available to you while you are using the Microsoft Windows operating system or the respective application program.
We have listed further useful sources of information in the section "Getting to know Windows® 7" starting on 53.
Audience
These instructions are intended for both the novice and advanced user. Regardless of the
possible professional utilisation, this All-In-One PC is designed for day-to-day household
use. The functions and applications for use with this All-In-One PC have been designed
with the entire family in mind.
Purchase Details
Enter your purchase details below for quick reference.
Serial Numbers
......................................
(i.e. Microsoft®)
......................................
Place and date of Purchase
......................................
You will find the All-In-One PC serial number on the rear of the All-In-One PC. Also copy
this number into your warranty documents, if necessary.
Quality
Medion has selected the components in this computer for their high level of functionality,
ease of use, safety and reliability.
Through balanced hardware and software design we are able to provide you with an innovative personal computer useful for applications relating to both work and leisure.
We are pleased to welcome you as our newest customer. Thank you for choosing our
products.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
iii
Table of contents
Safety............................................................................................................ 1 Operational Safety .......................................................................................................3 Power Supply...........................................................................................................4 Data Security............................................................................................................5 Battery Treatment ....................................................................................................6 Setting Up & Getting Started ....................................................................... 7 Included with your All-In-One PC ................................................................................9 Setting Up of the All-In-One PC .................................................................................10 Installing the Device ...............................................................................................10 Set-up Location ......................................................................................................10 Ambient Temperature ............................................................................................11 Ergonomics ............................................................................................................11 Connecting ...............................................................................................................13 Cabling ..................................................................................................................13 Connect the Antenna for TV Reception ..................................................................14 Connecting USB Devices ........................................................................................14 Installing Wireless Keyboard & Mouse ................................................................15 Inserting Batteries in Mouse ................................................................................15 Inserting Batteries in Keyboard............................................................................16 Inserting Batteries in the Remote Control ............................................................16 Connecting the USB Receiver ..............................................................................17 Setting the Frequency for Keyboard, Mouse and Remote Control .......................17 Connecting a Sound Source/Audio Input ...............................................................18 LAN Connection .....................................................................................................18 Connecting PS/2 Devices .......................................................................................18 Connecting Speakers/Audio Output ......................................................................19 Connecting a Microphone .....................................................................................20 Connecting the Power Supply ...............................................................................20 Getting Started ..........................................................................................................21 Step 1: Power On ...................................................................................................21 On/Off Switch ....................................................................................................21 Step 2: Starting Initial Setup ...................................................................................22 Step 3: Finalising ....................................................................................................22 Short Description of the Windows® Desktop ........................................................23 After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
iv
Operation ................................................................................................... 27 The Display ...............................................................................................................29 Operation ..............................................................................................................29 Cleaning ................................................................................................................29 Control Panel .........................................................................................................29 Screen Resolution...................................................................................................30 On-Screen Keyboard ..............................................................................................30 Comfort Light ........................................................................................................30 Appearance and Personalisation.............................................................................31 The Mouse ................................................................................................................32 The Keyboard ............................................................................................................33 The Alt and Ctrl Keys ..............................................................................................33 Multimedia Functions ............................................................................................34 The Hard Drive ..........................................................................................................35 Important Directories .............................................................................................36 The Optical Drive ......................................................................................................37 Loading and Removing a Disc ................................................................................37 Loading a Disc ....................................................................................................37 How to Remove a Disc ........................................................................................38 Emergency Ejection of a Blocked Disc .................................................................38 Playing Back and Retrieving Data from Discs ..........................................................39 Regional Playback Information for DVD ..................................................................39 Subjects Concerning the CD/DVD-Rewriter ............................................................40 The Card Reader ........................................................................................................41 Inserting Memory Cards .........................................................................................41 Removing Memory Cards .......................................................................................41 The Sound System.....................................................................................................42 Configuration of the Loudspeakers ........................................................................43 Webcam ....................................................................................................................44 Actual Example using Windows Messenger............................................................44 Microphone Amplification......................................................................................44 USB Port ....................................................................................................................45 The TV Tuner Card ....................................................................................................46 The Remote Control ..................................................................................................47 Button Layout ........................................................................................................48 The Network .............................................................................................................50 What is a Network? ................................................................................................50 Wireless LAN ..........................................................................................................51 Safety Note .........................................................................................................51 Conditions ..........................................................................................................51 Troubleshooting within the Network .....................................................................52 After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
v
Software ....................................................................................................................53 Getting to Know Windows® 7 ................................................................................53 Windows® 7 - News .............................................................................................53 Homegroup ........................................................................................................55 Windows® 7 - Help and Support ..........................................................................55 Windows® 7 -Getting Started ...............................................................................56 Windows® 7 - User Account Control ....................................................................57 Windows® 7 – Control Panel ................................................................................58 Windows Media Center ..........................................................................................59 Installation of Software ..........................................................................................62 How to Install your Software...............................................................................62 Software Uninstallation .......................................................................................63 Windows Activation ...............................................................................................64 Product Activation on Your All-In-One PC ...........................................................64 BIOS Setup .............................................................................................................65 Execution of the BIOS Setup ...............................................................................65 BullGuard Internet Security ....................................................................................66 Customer Service & Self Help ..................................................................... 69 Data and System Security ..........................................................................................71 Data Security..........................................................................................................71 Maintenance Programs ..........................................................................................71 System Restore ..........................................................................................................72 Correction ..............................................................................................................72 Windows® Update ..................................................................................................73 Windows Update Information for Data Security ..................................................74 System Restore ..........................................................................................................75 Limits of the Recovery ............................................................................................75 Carrying out a Restore............................................................................................75 FAQ – Frequently Asked Questions ............................................................................76 Customer Service ......................................................................................................77 Troubleshooting ....................................................................................................77 Localise the Cause ..................................................................................................77 Errors and Possible Causes .....................................................................................78 Additional Support.................................................................................................79 Driver Support .......................................................................................................79 Transporting the All-In-One PC ..............................................................................80 Cleaning and Care .................................................................................................80 Repairs ......................................................................................................................81 Notes for Service Engineers ....................................................................................81 Notes on Laser Radiation: ....................................................................................82 Recycling and Disposal ..............................................................................................82 After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
vi
Appendix .................................................................................................... 83 Standards ..................................................................................................................85 Electromagnetic Compatibility ...............................................................................85 Electrical Safety ......................................................................................................85 Ergonomics ............................................................................................................85 Noise Emission .......................................................................................................86 ISO 13406-2 Class II ...............................................................................................86 Information about the Regulatory Compliance according to R&TTE ......................88 FCC Compliance Statement ...................................................................................89 Making Copies of this Manual ................................................................................89 Index .........................................................................................................................90 After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Chapter 1
Safety
Operational Safety
Safety
Page
.......................................................... 3
Power Supply .............................................................. 4
Data Security .............................................................. 5
Operation
Subject
Connecting
1
Appendix
Help
Battery Treatment ........................................................ 6
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
2
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Operational Safety
Safety
3
Do not allow children to play unattended with electrical equipment. Children are
incapable of judging potential risks properly.

Keep the packing materials, such as plastic sheeting away from children. The danger of suffocation could arise in the case of misuse.

Do not open the All-In-One PC casing or use the All-In-One PC with the casing removed. When the casing is open there is a danger to life from electric shock.

Optical drives are Laser Class 1 devices. These lasers must remain in their sealed AllIn-One PC casing. Do not remove the drive covers, as exposure to the lasers may
prove harmful.

Do not insert objects through the slots and openings of the All-In-One PC. This may
lead to electric shock, electrical short-circuit or fire that will damage your All-In-One
PC.

Do not cover the slots and openings in the All-In-One PC casing. These openings
are for ventilation purposes. Covering these vents may lead to overheating. Please
keep free a minimum distance of 20 cm on all sides when setting up the All-In-One
PC.
Operation

Help
This ensures a reliable operation and long life expectancy of your All-In-One PC.
Connecting
Please read this chapter carefully and observe all listed notes.

… if the power cord or the connectors attached to it are burnt or damaged. Replace
the defective power cord with an original power cord. Under no circumstances may
a defective power cord be repaired.

... if the housing of the All-In-One PC is damaged or fluids have leaked into it. Have
the All-In-One PC checked by customer service first, because the All-In-One PC may
not be safely operated otherwise and there may be a life-threatening risk of electrocution!
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Appendix
Switch off your All-In-One PC immediately or do not switch it on at all and contact the
MEDION Help Desk on 1 300 884 987
4
Power Supply

Do not open the housing of the mains adapter. Opening the housing may cause
death by electrical shock. The housing contains no parts requiring maintenance.

The mains adapter should only be operated using earthed sockets with AC 100240V~, 50/60 Hz. If you are not certain of the electrical supply at the installation location, ask the power supplier.

The socket must be located near the All-In-One PC and must be easily accessible.

Use the enclosed mains adapter with the enclosed mains connection cable only.

For additional safety, we recommend the use of a surge protector, in order to protect your All-In-One PC from damage by voltage peaks or lightning carried through
the power network.

If you wish to separate the mains adapter from the power network, first pull the
plug out of the socket und then pull the plug on the All-In-One PC. Pulling the
plugs in the wrong order may damage the mains adapter or the All-In-One PC.
When pulling the plug, hold the plug itself. Never pull on the cord.
Note
Be sure to shut down the All-In-One PC properly before separating it from
the power or turning it off.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Data Security
Safety
5
Appendix
Help
Operation
Every time you update your data, make back-up copies on an external storage medium. The supplier does not assume liability for data loss or damage
to data storage units and no claims can be accepted for damages resulting
from the loss of data or consequential losses.
Connecting
Attention!
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
6
Battery Treatment
Batteries may contain combustible materials. Misuse may cause battery leakage, heat,
explosion or ignition, bringing about injury or damage to the device.
Please observe strictly the following matters:

Keep children away from batteries.
If by any chance, the batteries are swallowed, consult a doctor immediately.

Do not charge batteries (except rechargeable batteries).

Do not forcibly discharge batteries.

Do not short-circuit batteries.

Do not heat or dispose of in fire.

Do not disassemble or deform batteries.
Your hands and fingers may be injured, or the liquid of the battery may get into
your eyes or adhere to your skin. If this happens, rinse with a large quantity of water immediately and consult a doctor.

Do not expose batteries to strong impact by dropping or throwing the batteries.

Do not reverse the positive (+) and negative (-) terminals to avoid short-circuit.

Do not mix used and new or different types of batteries together.
Your equipment may not operate properly. In addition, the battery exhausted first
may be excessively drained (over-discharged).

Remove promptly the used batteries from the device.

Replace all batteries with new batteries of the same type at the same time.

Insulate the terminal parts with tape or the like when storing or disposing of batteries.

Check that the contacts in the device and on the batteries are clean and clean them
if necessary before inserting the batteries.

Do not throw rundown batteries in the domestic refuse! Respect the environment
and throw them in the specific containers for separate collection. If necessary, turn
to your retailer or to our service assistance. Thank you!
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Setting Up &
Getting Started
Subject
Page
Included with your All-In-One PC ..................................... 9
Setting Up ...................................................................... 10
Safety
Connecting
Chapter 2
Operation
7
Connecting ..................................................................... 13
.............................................................. 21
Appendix
Help
Getting Started
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
8
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Your All-In-One PC bundle should include the following components:

All-In-One PC

AC adapter with Power Cord
(Model Number: FSP150-ABAN1)

Keyboard, mouse and remote control set containing:
Wireless Keyboard +
2 Batteries type AAA, 1.5V

Wireless Mouse +
2 Batteries type AA, 1.5V

Wireless Remote Control +
2 Batteries type AAA, 1.5V

1 USB Receiver for Keyboard, Mouse and Remote Control

Software Package

Instruction Manual

Warranty Certificate

Warranty Stickers
Note
Keep the original packing in case the device ever requires shipment.
After Sales Support
Safety
Appendix

Connecting
Please check that the contents listed below are supplied with your package. You MUST
provide your All-In-One PC’s serial number when contacting a customer service representative.
Operation
Included with your All-In-One PC
Help
9
TEL: 1 300 884 987
WEB Support: www.medion.com.au
10
Setting Up of the All-In-One PC
Installing the Device
Diagram Reference: B

Unfold the foot on the back of the device.

You can set the foot at various angles, titling the All-In-One PC up to 20 degrees.
Note
Your All-in-One PC is supplied with an optional decorative strip. When the
All-in-One PC is wall mounted, this strip can be clicked in place between the
two front feet to close the gap.
Set-up Location

Keep your All-In-One PC and all units connected to it away from moisture, dust,
heat and direct sunlight. Failure to observe these instructions can lead to malfunctions or damage to the All-In-One PC.

To prevent damage to your All-In-One PC from a fall, place and operate the All-InOne PC and all connected units on a stable, balanced and vibration-free surface.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au

The All-In-One PC can be operated at an ambient temperature of between 10° and
35°C (+41° and +95°F) and at a relative humidity of between 30% and 70% (without condensation).

When powered off, the All-In-One PC can be stored at temperatures between -20°
and 50°C (–40° and +158°F).

Unplug the power adapter during thunderstorms and make especially sure to remove the antenna cables, if present. We recommend the use of a surge protector
for additional safety in order to protect your All-In-One PC from being damaged by
power peaks or lightning strikes through the power network.

Delay operating an All-In-One PC after transport until the device has adjusted to the
ambient temperature. In situations of large temperature or humidity differences
condensation may build up moisture inside the All-In-One PC, which might cause
an electrical short circuit.
Ergonomics
Safety
Connecting
Ambient Temperature
Operation
11
Ensure that the monitor is set up in such a way that reflections, glare and
light/darkness contrast are avoided.
Help
Note
Always position the monitor in a line of sight that runs parallel to the window front. You
should also apply a parallel line of sight with respect to artificial lighting. This means that
in a room lit by artificial light essentially the same criteria and objectives apply. Should it
not be possible to arrange the monitor as outlined above, the following measures might
be helpful:

Turn, lower or incline the monitor.

Place horizontal or vertical shades on the windows.
Note
Take regular breaks from your screen to prevent tenseness and exhaustion.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Appendix
You should not position the monitor in close proximity to a window as this is usually the
brightest area of the room and may cause visual impairments during daylight hours.
12
Sitting in one position for long periods can be uncomfortable. To minimise the potential
for physical discomfort or injury, it’s important that you maintain proper posture.
Overall:
Change your position frequently and take regular breaks to avoid fatigue.
Back:
While sitting at your work surface make sure your back is supported by the chair’s backrest. This should be in an erect position or angled slightly backwards.
Legs:
Your thighs should be horizontal or angled slightly downward. Your lower legs should be
near a right angle to your thighs. Your feet should rest flat on the floor. If necessary, use a
footrest but double check that you have your seat height adjusted correctly before getting
a footrest.
Arms:
Your arms should be relaxed and loose, elbows close to your sides with forearms and
hands approximately parallel to the floor.
Wrists:
Your wrists should be as straight as possible while using the keyboard, mouse or trackball.
They should not be bent sideways or more than 10 degrees up or down.
Head:
Your head should be upright or tilted slightly forward. Avoid working with your head or
neck twisted.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Cabling
Please follow the instructions below in order to correctly connect your All-In-One PC:

Arrange cables in such a way that no one can tread on or trip over them.

Do not place objects on the cables.

To avoid damage to your All-In-One PC, connect your peripherals (e.g., keyboard,
mouse and monitor) whilst your All-In-One PC is powered off. Some devices can be
connected whilst your All-In-One PC is in use. These devices usually have a USB
connector. Please follow the appropriate instructions for each device.

Keep the All-In-One PC at least one meter (approximately three feet) away from
high frequency and magnetic interference sources (e.g., televisions, loudspeaker
cabinets, mobile telephones, etc.) in order to avoid malfunctions and/or loss of
data.

Please note that only shielded cables shorter than 3 meters (9.84 ft) should be used
for the external interfaces. Please only use double screened cables for printer cables.

Do not replace the cables supplied with the machine by any others. Use only cables
supplied with your All-in-One PC because they will have been tested extensively in
our laboratories.

Also only use the connection cable supplied with the devices for the connection of
your peripheral devices.

Make sure that all connection cables have been connected to the peripheral devices
associated with them in order to avoid disruptive radiation. Remove unnecessary
cables.

Only devices complying with the following safety requirements should be
connected to your All-in-One PC: "EN60960 Safety of information technology
equipment" or "EN60065 Audio, video and similar electronic apparatus".
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Safety
Connecting
The devices listed are not necessarily included with your All-In-One PC.
All the connections listed are optional and might not all be available on
your All-in-One PC.
Operation
Note:
Help
Connecting
Appendix
13
14

In the first hours of operation, new devices may emit a typical, unavoidable but
completely harmless smell, which will decline increasingly in the course of time. We
recommend that you ventilate the room regularly, in order to counteract the formation of the smell.
Connect the Antenna for TV Reception
Diagram reference: C
The All-In-One PC comes equipped with a TV card. Connect one antenna cable to the
antenna connection, in order to receive the TV program on the All-In-One PC.

Connect a terrestrial antenna cable for terrestrial or cable reception.

Connect a DVB-T antenna if you have DVBT-T or digital services at your location.
Connecting USB Devices
Diagram reference: E
Warning!
Connect your USB devices after initial set-up of your new All-In-One PC.
This will prevent unnecessary confusion during installation. These devices
can generally be connected during operation. Read the manual for your peripheral device first.

The voltage outputs of your All-In-One PC for USB are protected by a fuse (which
complies to the specifications of a "limited power source" according to the technical
standard EN60950). This ensures that a malfunction of the All-In-One PC will not
damage the peripheral devices connected to the respective jacks.
You have a choice of several connection sockets. It does not matter which one you use.
Note
Take care that the connector and the socket fit exactly to avoid damaging
the contacts. Because of its asymmetric form the plug only fits into the
socket in one position.
1. If you wish to use a printer, scanner or other device with a USB port, connect the
cable to the USB socket on your All-In-One PC.
Note
Always connect your device to the same port otherwise your operating system will give a new ID and will ask for driver installation.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
The wireless keyboard and mouse operate with digital radio technology to ensure their
individual signals are not mixed up or cause interference. The transmission and receiving
of keyboard, mouse and remote control signals are free from angle restriction. Before
working with your new keyboard and mouse, ensure you take the following steps.
Beware!
Please read and follow the security advices concerning the use of batteries
on page 6.
Inserting Batteries in Mouse
The mouse requires two batteries type AA, 1.5V.
1. Remove the battery compartment cover on the bottom of the
mouse.
Safety
Connecting
Installing Wireless Keyboard & Mouse
Operation
15
3. Replace the battery compartment cover on the bottom of
mouse.
Help
2. Insert the 2 batteries type AA in the battery compartment. The
illustration in the battery compartment shows how to insert the
batteries properly.
Change the batteries if it is no longer possible to operate the mouse cursor
on the screen without interruption.
The operation of the mouse is described on page 32.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Appendix
Note
16
Inserting Batteries in Keyboard
The keyboard requires 2 batteries
type AAA, 1.5V.
1. Remove the battery compartment cover on the bottom of the keyboard.
2. Insert 2 batteries type AAA,
1.5V. The illustration on the
cover shows how to insert
the batteries properly.
3. Replace the battery compartment cover on the bottom of the keyboard.
Note
Change the batteries when you notice the All-In-One PC does not register all
of your keystrokes.
The operation of the keyboard is described on page 33.
Inserting Batteries in the Remote Control
The remote control requires 2 batteries type AAA, 1.5V.
1. Remove the cover from the battery compartment on the underside of the remote
control.
2. Insert 2 batteries type AAA, 1.5V. The illustration on the battery compartment cover
shows how to insert the batteries properly.
3. Replace the battery compartment cover on the bottom of the remote control.
Note
Change the batteries when you notice the All-In-One PC does not respond
to commands from your remote control.
The operation of the remote control is described on page 47.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Connecting the USB Receiver
Safety
17
1. Push the ‘connect’ button located on top of the receiver. The indicator will start
blinking.
2. Push the button on the bottom of the keyboard. The channel will be changed after
the button is released.
3. Push the ‘connect’ button located on top of the receiver. The indicator will start
blinking.
4. Push the button on the bottom of the mouse. The channel will be changed after the
button is released.
5. Push the ‘connect’ button located on top of the USB receiver. The indicator will
start blinking again.
Operation
Setting the Frequency for Keyboard, Mouse and Remote Control
Connecting
1. Attach the receiving station for the mouse, keyboard and remote control to a free
USB port on your All-In-One PC.
Appendix
Help
6. Briefly press the key underneath the battery cover on the battery compartment.
When you release the key, the frequency will have changed.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
18
Connecting a Sound Source/Audio Input
Diagram reference: F
This port is used to accommodate a connecting cable for external analogue audio sources
(i.e. stereo system, keyboard/synthesizer).
1. Connect the cable with the 3.5 mm stereo jack plug to the light-blue coloured
socket marked with the symbol
.
Note
You can also connect a sound system to the audio socket. For further information, read the section beginning on page 42.
LAN Connection
Diagram reference: G
Your All-In-One PC is equipped with a network connection, in order to prepare it for network operation.
The network cable usually has two RJ45 plugs so that it is unimportant which plug is connected to which jack.
1. Connect the one plug of the cable to the All-In-One PC jack
.
2. Connect the other plug to the other All-In-One PC or hub/switch.
For further information refer to chapter "The network" starting at page 50.
Connecting PS/2 Devices
Diagram reference: H
You can omit this step if you want to connect the mouse or keyboard set delivered with
your All-In-One PC.
1. Connect the mouse cable to the right, green PS/2 port.
2. Connect the keyboard to the left, blue PS/2 port.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Connecting Speakers/Audio Output
Safety
19
Here you can connect your active speakers for playback of sound or audio connection
cables for recording. Please refer to the user's guide of your stereo installation for information about which connector you should use (usually Line In or Aux).
1. Connect the cable with the 3.5 mm stereo jack plug into the green socket marked
with the symbol
.
Connecting
Diagram reference: L
You can also connect a sound system to the audio socket. For further information, read the section beginning on page 42.
A digital output (S/PDIF) can be linked with a coaxial cable.
Diagram reference: D
Operation
Note
1. Plug a cinch cable into the socket at Position D.
You can also connect headphones to the analogue audio gateway.
Diagram reference: L
Connect the cable with the 3.5 mm stereo jack plug in the green socket.
Caution!
The use of headphones/earphones with a high volume can lead to lasting
damage to your hearing. Set the volume to the lowest level before playing
back and any sound. Start play back and increase the volume to the level
that is comfortable for you. Changing the basic settings of the equalizer can
also cause damage to the hearing of the listener.
It can cause damage to the hearing ability of the
listener if a device is operated through earphones with an
increased volume for a long period.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Appendix

Help
2. Connect the other end of the cable to an audio device with a corresponding digital
gateway.
20
Connecting a Microphone
Diagram reference: M
1. You can use the pink socket
jack plug.
to connect a microphone with a 3.5 mm mono
Position the microphone in such a way that it does not point directly at the speakers. If you
hear feedback, characterised by loud whistling noises, reposition the microphone until the
sound stops.
Note
You can also connect a sound system to the audio socket. For further information, read the section beginning on page 42.
Connecting the Power Supply
Diagram reference: I
When you have made all the connections, establish the power supply by connecting the
mains adapter supplied with the All-in-One All-In-One PC.
1. Link the 3-pin mains adapter plug of the mains cable into the corresponding socket
of the mains adapter.
2. Plug the device plug of the mains adapters into the DC IN mains plug socket on the
back side of the All-In-One PC.
3. Plug the mains plug on the mains cable into a 240 V ~ 50 Hz wall socket.
Note
The power supply unit has an On/Off switch. When the switch is Off (0) no
power is being consumed.
Do not start your All-In-One PC yet!
First, read the following section to find out what you need to know in order to get started.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
The software on this All-In-One PC comes fully pre-installed. You do not have to load any
of the CD's/DVD’s supplied.
With many programs (e.g., telephone-CD's or encyclopaedias), however, it is necessary to
insert the corresponding CD/DVD in order to call up the data which is stored on it. The
software will ask you to do this this if necessary. Once you have made all the connections
and secured the necessary connectors you can turn on the monitor, the other peripherals
and finally the All-In-One PC itself.
Operation
Step 1: Power On
Safety
Getting Started
Connecting
21
On/Off Switch
Diagram reference: K
The On-/ Off switch function can be programmed in the Windows® Control Panel, Power
Options, Hardware and Sound (please refer to on-line help). The All-In-One PC will always be switched off, if the main switch is pressed for more than 4 seconds.
Help
1. Press the On/off at the front once to start loading the operating system.
Warning!

), then there is a risk of data loss.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Appendix
If the operating system is not shut down properly (through
22
Step 2: Starting Initial Setup
The All-In-One PC starts and now goes through a number of phases:
Note
Ensure that there is no bootable CD (e.g. the Recovery-CD) in the CD-ROM
drive. Such disks will prevent the operating system from loading directly off
the hard drive.
The operating system is loaded from the hard disk. During the initial set-up, the loading
process takes slightly longer than normal to register the operating system and the individual components completely. Your operating system is finished loading when a welcome
screen is shown on your display.
Follow the instructions on the screen. Dialogue boxes will explain any steps that need to
be taken. The greeting procedure will guide you through the following screens and dialogues.
Should you have any questions just click on
.
License agreement
Please read through the license agreement carefully. It contains important legal information on the use of your software. In order to see the full text, use the mouse and the scroll
bar to move downwards until you have reached the end of the document. You accept the
agreement by clicking on the I accept the agreement option field. Only by doing so will
you be entitled to use the product under lawful terms and conditions.
Step 3: Finalising
After the login procedure the Windows® desktop appears on your screen.
This can be adjusted so that the screen of your computer looks different. The basic operation, however, is ensured.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Short Description of the Windows® Desktop
Safety
23
 All Programs
All of the software programs installed on your All-In-One PC are ordinarily listed here.
Click All Programs to reveal an extensive menu.
 Taskbar
You can start programs and switch between already active programs using the taskbar
beneath the screen. You can place every program in the taskbar under Windows® 7, so
that you can always open it with a single click. Furthermore, you can rearrange the
symbols on the taskbar by clicking on them and dragging them to the desired position.
Move the cursor over the symbols, and the system will display a miniature of every file
or window open in the program. When you move your cursor over the miniature, the
system will display a full-screen preview of the particular window. If you move the cursor away from the miniature, the full-screen preview will close.
Operation
Clicking the Start button brings up a menu where you can access help, software programs, files, and settings
Connecting
 Start Button
 Program Bar
The most commonly used software programs are listed here. The operating system
recognises all this automatically. Clicking on an entry with the right mouse key enables
you to decide which entry on the list to keep or to remove. The program linked to the
input is not erased.
 Turn Off
To turn off the All-In-One PC, click on the Shut down button with the left mouse key.
 Desktop
Click on this Button if you would like to minimise all the windows open onto the taskbar, in order to obtain a clear view of the Desktop.
 Desktop Icons
Desktop icons link to their respective programs. To start a program, double-click its
desktop icon.
The desktop encompasses nearly the entire screen and acts as the shelf space for such
entries or for other links, to which you would like rapid access.
 Logged in User
This tells you which user is logged in to your All-In-One PC.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Appendix
Windows Search helps you find almost all data located on the All-In-One PC, quickly
and easily. With Windows® 7, you get search results with greater relevance, and they
are easier to understand.
Help
 Windows Search
24
 Control Panel
You can use the icons in Control Panel to change the appearance and functionality of
Windows®7. These icons represent options for configuring your All-In-One PC. You
should, however, consult "Help and Support" on the potential effects of certain
changes.
 System tray
System tray on the current time. When certain events occur, for example, upon receipt
of an e-mail message or upon opening the task manager, it may happen that too many
notification symbols are displayed in this field. Windows® displays a notification symbol
when an event occurs. After a short time, Windows® places the symbol in the background, in order to maintain the straightforwardness of the field. You can access the
symbols placed in the background by clicking on a button in the system tray.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Safety
Appendix

  



Help
Operation
Connecting
 
25
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
26
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Chapter 3
Operation
Safety
Page
The Display ....................................................................... 29
The Mouse........................................................................ 32
The Keyboard ................................................................... 33
Operation
Subject
Connecting
27
The Hard Drive.................................................................. 35
The Optical Drive .............................................................. 37
The Sound System ............................................................ 42
The Webcam .................................................................... 44
Help
The Card Reader ............................................................... 41
The USB Port ..................................................................... 45
The TV Tuner Card ............................................................ 46
Network .......................................................................... 50
Software ......................................................................... 53
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Appendix
The Remote Control ......................................................... 47
28
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Operation

To avoid damage, do not touch the display with sharp or sharp-edged objects.

Use a blunt stylus or your finger.
Cleaning

Take care to avoid water drops remaining on the display. Water can cause permanent discoloration.

Clean the screen with a soft, lint-free cloth.

Do not expose the screen to bright sunlight or ultraviolet rays.

Never use solvents, or caustic or volatile cleansers.

To clean the display, use only suitable cleansers such as glass cleansers or monitor
cleansers (available in the retail shops).
Safety
Connecting
Your All-In-One PC includes a touch-sensitive screen. To ensure optimal use, you should
pay careful attention to the following notes:
Operation
The Display
Help
29
Control Panel
On the right side of the display, you will see a control panel with sensor keys, enabling you
to adjust the image and sound.
One of the following commands will be carried out whenever you tap a field with your
finger.

Brighter
Increases screen brightness.

Darker
Decreases screen brightness.

Louder
Increases volume of sound reproduction.

Softer
Decreases volume of sound reproduction.

Mute
Switch mute switch on or off.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Appendix
Diagram reference: J
30
Screen Resolution
The screen has a native resolution of 1920 x 1080 pixels. If you change to a presentation
with different characteristics in the Windows "Control Panel  Appearance and
Personalization  Display Settings Adjust screen resolution" Help Program, the display will not appear on the whole area of the screen, among other effects. Using a higher
resolution can lead to distortion of the display, especially with text. Using a lower resolution may cause the display to use only a portion of the screen area.
You can adjust the presentation to the mode supported with the Windows "Control Panel
 Appearance and Personalization  Display Settings  Adjust screen resolution 
Advanced Settings" Help Program.
On-Screen Keyboard
Using the On-Screen Keyboard application displays a virtual keyboard on the screen,
allowing you to input data by means of a pointer or joystick, or directly, using the touch
screen.
To retrieve the on-screen keyboard, proceed as follows:
1. Click on the Windows desktop with the right mouse key.
2. Click on the Personalization point in the selection menu.
3. Select the Ease of Access Center.
4. Click on Start On-Screen Keyboard.
Comfort Light
The comfort light is located between the lower edge of the display and the feet of your Allin-One PC.
The ‘LED Control’ Desktop icon will start the software. You will have to activate the program manually with a double-click after you start up the system.
You will be able to make the colour settings of the comfort light manually after the software has been started:
icon in the
1. Press the Shift+Ctrl+L key combination or a double-click on the
Windows Taskbar, at the lower right hand corner of your screen, to do this.
2. Here, you will be able to choose one of 7 different colours as the comfort light with
a mouse click or with the 1 – 8 number keys, or by touch, or switch off the comfort
light with number key 8 (black).
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
This program offers you the possibility of adjusting the presentation on your display. This
includes the background image, the screensaver, Active Desktop (web) and additional
settings of your display and your graphics card, for example. The program can be started
in the following way:

Right mouse click on the Windows interface (Desktop) and left mouse click on
Personalization
or
Via Start  Control Panel  Appearance and Personalization with a double-click
with the left mouse button.
The following adjustment possibilities are available:

Personalization

Display

Desktop Gadgets

Taskbar and Start Menu

Ease of Access Center

Folder Options

Fonts
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Appendix
Help
Operation

Safety
Appearance and Personalisation
Connecting
31
32
The Mouse
The mouse has beside the two keys a wheel that can be used to scroll through a document
or internet pages.
Note
The scroll wheel can be used as a button. The functionality depends on the
application. In Word for example you can push the wheel to move up and
down as a scroll function.
If the mouse course moves jerkily on the screen, try a different surface (mouse pad). Glass
and metallic surfaces might cause problems.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
The Alt and Ctrl Keys
The left Alt key performs certain functions in conjunction with other keys. The application
program determines these functions. In order to enter a combination of keys that include
the Alt key, hold the Alt key down while pressing the other key. The right Alt key operates
in a similar way but selects certain special characters. The Ctrl key, like the Alt key, carries
out program functions.
Useful key combinations (software-dependent):
Key Combination
Function and Description
Alt + F4
As a rule ends the program selected or closes the window
opened.
Alt + Print screen
Copies the image of the window currently active to the
clipboard.
Shift + '
Generates the @ character required for e-mails (pronounced: at).
Ctrl + Alt + Del
Windows security is launched.
Safety
Connecting
This section contains useful information on using the keyboard. All diagrams are
schematic.
Operation
The Keyboard
Help
33
Appendix
(Country-specific variances are possible.)
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
34
Multimedia Functions
The allocation of a double function to certain keys provides you with a few multimedia
functions. Some functions are input using the Fn-Key:
Kombination
Fn + 
Description
Previous Track
Use this key to skip backwards to the previous track/title in the
active player.
Fn + /
Play/Pause
Use this key to start or pause, for a short time, the playback of a
track/title just as you would with a normal CD player.
Fn + 
Stop
Use this key to end playback of the current track/title.
Fn + 
Next Track
Use this key to skip forward to the next track/title in the active
player.
Single Button
Description
Mute
Switches the volume on/off.
Decreases the volume.
Increases the volume.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
The hard drive is the main storage medium combining large storage capacity and rapid
data access.
The hard drive contains the operating system of the computer, other application programs
and backup files. These programs and files are pre-installed on your All-In-One PC, so you
may note that some of the space on your hard drive is already taken.
The Windows operating system cannot use the full capacity of the hard drive, which
means that there will be a difference between the capacity that the BIOS displays and what
the operating system displays. The operating system of the All-In-One PC, further application programs and backup files are located on the hard drive and reduce its total capacity.
The hard drive is addressed as drive C and D.
Note
Safety
Connecting
The Hard Drive
Operation
35
Usually your hard disk is divided into more partitions. The configuration of your hard drive
can be displayed and configured under "Disk Management". To familiarise yourself with
the hard drive configuration, search Windows Help for the key word "Disk Management".
Help
Never switch off the computer while the busy indicator is lit since this may
result in loss of data. A flickering hard drive display is your indication that the
All-In-One PC is accessing the hard drive.
The second partition (D:\) serves for data security and contains additional drivers
(D:\Driver) and tools (D:\Tools) for your All-In-One PC.
Note
You will also find in two otherwise non-overwriteable partitions the system
restoration start files ( p. 75), as well as installation files for Windows® 7.
These partitions are not visible and should not be erased.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Appendix
In your first partition (C:\) you will find the operating system, application programs and
the users’ documents.
36
Important Directories
In the following we have listed the most important directories and described their content.
Attention!
Do not delete or modify these directories or their contents since data could
be lost or the functionality of the system could be at risk.
C:\
The master directory of drive C: includes important files required to
start Windows®. In the factory setting these files are hidden for safety
reasons.
C:\Programs
As the name suggests, in this directory programs install the files belonging to the application.
C:\Windows
The main directory of Windows®. This is where the files of the operating system are saved.
D:\Driver
This folder includes the drivers required by your computer (preinstalled).
D:\Tools
Here you find additional programs and other documentation for your
All-In-One PC.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
The Optical Drive
Safety
37
Loading and Removing a Disc
In contrast to optical drives in a desktop All-In-One PC, your All-In-One PC uses a holder to
lock the disk.
Connecting
Diagram reference: A1-A4
Help
Do not place protective foils or other stickers on your CD’s. To avoid damage to your drive, do not use deformed or damaged CD’s. Attention: Do
not use scratched or dirty discs, discs with pieces broken off or discs of poor
quality. Because of the high speeds in the drive the discs might break and
damage your data as well as your drive. Examine the discs before you enter
them. If damage or dirt is visible, you should not use them.
Damage caused by faulty media is excluded from warranty and any repair
will be charged.
Operation
Attention!
Loading a Disc
1. With the device turned on, press the eject button on the optical drive (Diagram reference A3) to open the tray.
Appendix
2. Pull the tray out completely with care.
3. Place the disc on the tray so that it lays flat with the
label facing forward. push the disc right onto the
locking mechanism so that it can lock in position.
holder
Attention!
The disc can be damaged when the drive drawer is pushed in, if it has not
been positioned on the support correctly.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
38
4. Push the tray back into the optical drive carefully.
The ‘E’ drive letter will have been allocated to your optical drive in the delivery
status. You will have easy access to your files on your disks with Windows Explorer
(Computer). Start the Computer Help Program by means of the Desktop link
or by pressing the Windows key
and the ‘E’ key at the same time. Open Windows Explorer by means of Start  All Programs  Accessories. The pre-installed
media reproduction will be used automatically during access to DVD videos (or audio and video files on normal data CDs)..
Attention!
While the All-In-One PC is accessing the optical drive the media acitvity indicator (Diagram reference A4) is lit. Do not try to remove the disc from the
drive while this LED is lit.
How to Remove a Disc
1. To remove a disc push the eject button (Diagram reference A3) again to open the
drawer.
2. Remove the disc and store it at a safe place.
3. Shut the drawer.
Emergency Ejection of a Blocked Disc
If the tray fails to open automatically, then the tray can be opened manually provided
there is an opening for emergency ejection.
1. Shut down Windows and switch off the All-In-One PC.
2. Insert a long thin object (like a straightened paper clip) into the emergency ejection
(Diagram Reference A2) opening until you feel resistance.
3. Press lightly and the tray will open.
4. Remove the disc and restart the All-In-One PC.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Playing Back and Retrieving Data from Discs
Safety
39
Some discs start automatically upon insertion. This depends on the operating system and the related settings.
Your All-In-One PC is able to playback and to retrieve Audio CDs, DVD Movies and Data
discs.
Connecting
Note
If your operating system doesn’t open the selection window you still have the possibility of
access to the optical drive via the Windows Explorer or the Computer
.
Regional Playback Information for DVD
Operation
After loading the disc your operating system will open a selection window with different
options for playback.
Among the numerous regulations for CSS licensees the most important ones are the country specific playback restrictions.
In order to facilitate the geographically restricted release of movies, DVD titles are released
for certain regions.
Copyright laws require the restriction of each DVD movie to a certain region (usually the
region, in which it is sold).
DVD movie versions can be published in several regions but the CSS regulations require
that each CSS decipherable system may only be used in one region.
Attention!
The decoding software included with your All-In-One PC may be changed
for regional DVD decoding up to five times, after which the drive will only
play DVD movies for the region setting last entered. Changing the region
code after that will require factory resetting which is not covered by warranty. If resetting is desired, shipping and resetting costs will be billed to the
user.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Appendix
CSS (sometimes called copy guard) is the name of a data protection program incorporated
by the movie industry as an action against illegal copies.
Help
The playback of DVD movies includes the decoding of MPEG2 videos, digital AC3 audio
data and the deciphering of CSS protected contents.
40
Subjects Concerning the CD/DVD-Rewriter
Normal discs are pressed from a digital, glass master and then sealed. In the case of blank
disc, the information is burnt onto the disc with the laser of the Rewriter. Therefore these
discs are more sensitive than normal CDs.
Please avoid the following when using recordable/rewriteable discs - especially blanks that have never before been used:

radiation by direct sunlight (UVA/UVB)

scratches and damage to the disk surface

extreme temperatures
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
The Card Reader
Safety
41
SD: Secure Digital Memory Card

MMC: Multimedia Card

SDHC: Secure Digital High Capacity Card

MS: Memory Stick

PRO: Memory Stick Pro
For other types of cards, you may need a corresponding adapter (not included).
Inserting Memory Cards
Operation

Connecting
Diagram reference: N
Your All-In-One PC is equipped with a card reader, which can read and write on several
memory card types. The following table refers to the use of the card reader:

Align the card in such a way that the contacts point backwards when the All-In-One
PC is upright.

Push the memory card into the slot.
If a card is inserted, a free drive letter will be allocated to it in the workstation.
Removing Memory Cards
In order to remove a memory card or a memory stick, first push it into the contact to
unlock it. Pull the card from the bay and store it securely.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Appendix
Memory cards can only be inserted in one direction. Do not attempt to insert a card by force. This can damage the card reader and/or the card.
Help
Note
42
The Sound System
Your All-In-One PC has an integrated stereo sound card (on-board) with 16-bit and 3D
spatial sound effects (3D). The sound card is compatible with the industry standard Sound
Blaster and Microsoft Sound System Version 2.0. This guarantees optimal support for all
popular programs and games. If you wish to alter the base volume, click on the loudspeaker symbol in the task bar.
Click on Mixer, in order to open the volume mixer.
By using the keys
and
you have also the possibility to regulate the volume.
You can change the function of the audio sockets using the pre-installed "Realtek" driver
software. The connections can be configured in such a way as to connect to a surround
sound system.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Configuration of the Loudspeakers
Diagram reference: F, L, M
Safety
43
Appendix
Help
Operation
In the Speakers dialogue, you can select the following settings under Speaker Configuration:
Connecting
Connect the plug of one audio device with one of the audio sockets. The device will be
recognised.
Stereo:
the audio sockets possess their basic functions.
Quadrophonic:
the blue socket is for the rear loudspeaker;
the green socket is for the front loudspeaker;
the pink socket is the microphone input.
5.1 loudspeaker:
blue and green sockets as with quadrophonic;
the pink socket is for centre loudspeaker and sub-woofer.
Dragging the cursor over the socket illustrations displays the current functions.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
44
Webcam
Diagram Reference: O
The built-in Webcam and associated microphone permit the use of various services, such
as Windows® Messenger.
Actual Example using Windows Messenger
1. Start Windows Messenger and create a user account if you do not already have
one. This service is free of charge. You only pay the cost of your Internet connection.
2. Select your contact from the list and click on the camera icon below your display
image.
A wizard helps you optimise the settings of your speakers, microphone and webcam. Follow the instructions on your screen.
3. Click on Finish to transmit your image via the webcam.
4. If your contact also has a webcam, click on the camera icon below the display image of your contact to receive the live image.
Microphone Amplification
You are also able to amplify the built-in microphone. To do this, start the Realtek HD Audio-Manager by double clicking on the loudspeaker in the Infobar.
In the Microphone dialogue, you can adjust or change the value of the microphone amplification.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
USB Port
Safety
45
Devices connected directly to the USB port should not draw more than 500
mA. The voltage output is protected by a fuse (Limited Power Source according to EN 60950). Should the devices need more power than this, it will
be necessary to provide a hub (distributor / booster).
On the USB it is possible to connect up to 127 devices which correspond to the USB standard (1.1 and 2.0 supported).
The data transfer speed is 1.5 Mbit/s or 12 Mbit/s, depending on the device connected.
USB 2.0 can reach up to 480 Mbit/s.
Operation
Note
Connecting
Diagram reference: E
Appendix
If possible, always connect your USB devices to the same port where it has
been installed. Otherwise you will get a new ID and your operating system
will ask for a new installation of the driver.
Help
Note
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
46
The TV Tuner Card
Diagram Reference: C
To receive a TV signal with the TV tuner, an analogue or DVB-T antenna must be connected. In this regard, see also page 14.
Attention!
Pull the antenna out when the device is not being used, particularly during
bad weather. This protects your device from lightning.
Windows® Media Center is the optimal software for digital television, digital photographs
and digital music.
1. Start the Media Center using the program bar (in this regard, see also page 59)
2. A assistant will guide you through the installation of your TV tuner.
Attention!
Audio or video recordings need a great deal of memory (up to 2.4 GB/hour).
Safeguard files that you do not need on external media, such as DVD/CD-Rs
or hard drives.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
This wireless remote control set can only be used to control the Media Center program on
your All-In-One PC. In order for it to work, the following conditions must be met:

The All-In-One PC must be booted up.

®
Windows must be fully loaded.

The driver software must be installed .
Appendix
Help
Operation
*
Safety
The Remote Control
Connecting
47
(fig. remote control)
*
This condition is met in the state the All-in-One PC is delivered in.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
48
Button Layout
Note
The functions described here are standard functions.
These Buttons can differ according to the operating mode (TV, video, photo,
etc.).
Start video text application.
Special function Button red (e.g.: for video text)
Special function Button green (e.g.: for video text)
Special function Button yellow (e.g.: for video text)
Special function Button blue (e.g.: for video text)
Application-related information function.
EPG function (Electronic Program Guide)
Reverts to the point selected previously.
Press  to select the next channel. You select the
previous channel with .
Mute Switch (switches the sound output off).
Press + to increase the volume. Press - to lower the
volume.
Starts Media Center.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
With these navigation keys, you can navigate between selection
and menu elements.
Safety
49
Previous title/images/chapter
Next title/images/chapter
Rewind
Starts playback.
Connecting
Press the OK button to confirm.
Ends the playback/recording
Pauses the playback at the selected point.
Appendix
Direct selection of the TV channels by means of numbers.
Number entry in the case of some functions (video text, etc.).
Help
Start recording
Operation
Fast forward
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
50
The Network
Diagram reference: G
Your All-In-One PC is provided with a Fast Ethernet-Network connector
You will find further information about networking in the Help section within the Start
menu.
What is a Network?
A network means connecting your All-In-One PC to another or several other All-In-One
PCs. Users can transfer information and data between computers and share resources such
as printers, modems and hard disk drives.
Here are some practical examples:

You can exchange Email and manage appointments in an
office.

Users share a printer in a network and save their data
on a central server.

Share one modem or one ISDN card among computers for Internet access.

Two or more All-In-One PCs can be connected to play network games or share
data.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Your All-In-One PC is equipped with WLAN. The components (Module, antenna) are already integrated and activated in your computer. You can turn off the wireless LAN func®
tion with the help of the Windows Device Manager.
This function allows you to create a wireless network link with a partner.
Safety Note
Safety
Wireless LAN
Connecting
51
Don’t use this feature in environments where highly sensitive devices are
placed such as in hospitals etc. To avoid any interference disable this option
in your device manager.
Operation
Attention!
Wireless access points are often found in offices, airports, universities or Internet cafés.
They offer access to enterprise services and networks or to the Internet.
Access authorisations are normally needed. A fee may be required to use a public access
point. To set up a wireless network to share Internet access, files, and printers at home,
you will need an access point, a router, and a broadband (DSL or cable) modem. Some
access points can also serve as a router and/or a broadband modem. Check with your
retailer to find the best solution for your needs.
A link to another computer with wireless LAN functionality can also be created without an
access point. This will allow you to share files, but you will need an access point and a
router to share an Internet connection. The wireless network link works according to standard IEEE 802.11n and is compatible to standard IEEE 802.11 b/g. Other standards
(802.11a etc.) are not supported.
*
The transmission speed (max. 300 Mbp/s ) can vary according to distance and other factors. If for example the other devices support the 802.11b standard the transmission speed
can be max. 11 Mbp/s.
Search for "wireless networking" in Windows Help and Support for more information.
*
300 Mbit/s is a grossvalue. A maximum of 75 Mbit/s is available at application level. In
order to use its full capacity, a WLAN router following the 802.1 1n standard is required.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Appendix
The partner used can be a wireless access point. An access point is a wireless transmitter
that communicates with your notebook and controls access to the network connection
(e.g., a home network or a broadband connection such as DSL).
Help
Conditions
52
Troubleshooting within the Network
Why does the network environment not show the releases?
The network environment is delayed in time. Check the release by
searching for the respective computer name.
Why does an error message appear when I click on the network environment?
The computer name must be unique on the network and may
not be the same as the task group.
It appears that the network boards are unable to communicate. What
might be the problem?
Maybe one of the used network boards works with a different
speed (e. g. 10 instead 100 Mbit) and your network computer is
unable to recognise this. If necessary, set the network driver to the
compatible speed.
If two PCs should be linked you require a cross-link cable, otherwise use a patch cable.
In addition, check the protocols and the configuration.
The data transmission is incorrect or very slow. What might be the
problem?
Maybe you have the wrong cable (UTP / CAT3 or lower) or the
problem is the proximity of a power cord or another source of
interference.
For further hints on troubleshooting refer to the Windows help under "Network errors".
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
This section concerns itself with software. We make a distinction between the operating
system, the software (application program), Windows activation, BIOS and the security
package BullGuard, which is delivered with the device.
Getting to Know Windows® 7
With Windows® 7, a new operating system is launched which succeeds Vista.
Windows® 7 contains a number of innovative functions and technologies, enabling your
All-In-One PC to work quickly and reliably, while being easy to use.
Windows® 7 - News
Safety
Connecting
Software
Operation
53
Jump Lists
Jump lists offer a practical possibility when opening files which you have recently worked
on. To display recently used files, just right-click the application symbol on the Taskbar.
Right-clicking on the Word symbol will display recently used Word documents. You can
also easily place other files in the jump list if you would like to have them readily at hand,
in which case they will always be displayed. This allows you to access documents which
you use more frequently, with just a few mouse clicks.
The jump lists from a few programs, such as Windows® Media Player, can be filled in advance with frequently used commands. Thus, for example, the Windows® Media Player
jump list might contain options to play all music or to re-open the latest play list.
The Internet Explorer jump list displays frequently and most recently visited websites. For
certain programs, this enables rapid access commands which, in the past, could only be
retrieved from the program itself, such as the command to create a new e-mail message.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Appendix
The Taskbar at the bottom of the screen enables you to start programs and change between programs which are already running. Using Windows® 7, you can place any program in the Taskbar, so that it will always open with one single click. You can also arrange
the symbols on the Taskbar simply by clicking on them and dragging them to the desired
position. The symbols are also considerably bigger, so that they are easier to use. Moving
the cursor over the symbols will display miniatures of each file or each window open in the
program. Moving the cursor over the miniature displays a full-screen preview of the particular window. Moving the cursor away from the miniature closes the full-screen preview.
Help
Improved Taskbar
54
Improved Desktop
Windows® 7 simplifies working with the windows on the Desktop. This provides you with
more intuitive possibilities for opening and closing, as well as for changing the size and for
rearranging.
Windows® 7 makes the performance of everyday tasks even simpler. For example, the
Snaps function makes it easier than ever to compare two open windows. You do not need
to adjust the size of the open window for comparison. Simply pull the window, using the
mouse, to one of the edges at the side of the screen, and it will fill half the screen. Snap the
window on both sides, and it is already easier than ever to compare two windows.
If you would like to display all Desktop mini-applications, simply move the mouse into the
lower right hand corner of the Desktop. This makes all open windows transparent, so that
the Desktop and all the mini-applications located on it will be instantly visible.
Click on the Titlebar of the window, "shake" it, and all open windows will be displayed as
symbols on the Taskbar. "Shake" the window again, and the other windows will be displayed again.
Better Device Management
Windows® 7 enables you to close, manage and use all devices through the "Devices and
Printers" central function.
All devices are displayed in a central position.
With the new Device Stage Technology, Windows® 7 even goes one step further in device
management. Device Stage helps you use all compatible devices connected to your computer. Thanks to Device Stage, now you display the device status in one single window
and carry out often-used commands. You will even find pictures of the devices here, easily
enabling you to see which devices are connected. The manufacturer of the devices can
even adapt Device Stage. If the manufacturer of your camera, for example, prepares an
adapted version of Device Stage, you can see the number of photos on the camera and
receive links to useful information when you link the camera to the All-In-One PC.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
With homegroups, a new function of Windows® 7, the linking of home computers is really
simple. A home network group is created automatically, for example, when you link the
first All-In-One PC under Windows® 7 with the home network. The addition of additional
All-In-One PCs with Windows® 7 to the home network group is quickly accomplished. You
can indicate exactly what should be released on each All-In-One PC for all other All-In-One
PCs in the home network group. Finally, the shared use of files on the various home All-InOne PCs, and on many other devices, is so simple that it is as if all files were located on
one single hard drive. This allows you to store digital photos on the computer in your
home office and then enjoy easy access to them from a laptop in any other room in the
house. Similarly, the printer in home office is automatically released for all All-In-One PCs
in the house, as long as they are all in the home network group.
Beginners and persons changing from other Windows versions systems are advised to read
this material carefully.
Windows® 7 - Help and Support
Safety
Connecting
Homegroup
Operation
55
This help function fully covers the Windows operating system.
It is helpful for both beginners and professionals. You can
print or bookmark the information, which is categorised into
topics. You start like this:
Help
An answer to almost every question can be found in this
program.
Appendix
1. Click on Start
2. Now select Help and Support
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
56
Windows® 7 -Getting Started
Learn everything you need to know about the features of the All-In-One PC.
It is the aim of this feature to enable both beginners and experienced users to make additional setting for the optimal use of Windows®7 after first bringing the All-In-One PC into
operation.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au

Go online to find out what’s new in Windows®7

Personalise Windows

Transfer files and settings from another computer

Use a homegroup to share with other computers in your home

Choose when tob e notified about changes to your computer

Back up your files

Add new users to your computer

Change the size of the text on your screen
Use Getting Started to understand your All-In-One PC better and in order to be able to
use it optimally. It will also serve you as an additional source of information for recognizing and removing potential problems.
You will call up Getting Started as follows:
Safety
Connecting
Getting Started has been subdivided into many small groups of subjects, so that the user
will have the possibility of adjusting the content optimally to his or her knowledge. There
are some of the links in the following:
Operation
57
2. Select
Getting Started in the Program List.
Windows® 7 - User Account Control
Help
1. Click on Start
A window with the message "Do you want to allow the following program to make
changes to this computer?" will appear as soon as you carry out an unauthorised
change.

Click on Continue, in order to continue the procedure.

Click on Cancel, in order to end the procedure.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Appendix
The User Account Control contributes to the prevention of unauthorised changes to the
All-In-One PC.
58
Windows® 7 – Control Panel
You can change Windows settings using the control panel. The settings control almost
everything relating to Windows displays and functionalities, and they enable you to organise Windows according to your requirements.
When you first open the Control Panel, a few of the most frequently used elements of the
Control Panel are displayed by category.
For further information on any element in the Control Panel category view, hold the cursor
over the symbol or category name and read the pop-up display text.
To open one of these elements, click on the associated symbol or category name.
For a few of these elements, a list, with executable tasks will open, with a selection of individual Control Panel elements.
Searching for the desired control elements may be effected in the following ways:

Enter a word or expression in the search field.

Click on Large Icons or Small Icons under Display Settings to display a list of all
Control Panel elements.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
The Windows Media Center is the platform for your individual home entertainment in
Windows® 7. You will be able to record television, TV broadcasts, DVDs and music, look at
photos and much more by a remote (not included in the scope of the delivery) or by a
click of the mouse, with the Windows Media Center.
You will start your individual entertainment as follows:
1. Turn on your All-In-One PC.
.
2. Click on Start
An overview of the Windows Media Center functions is below:
Main menu
Sub-menu
TV + Films
Recordings
You will have the possibility of recording broadcasts if you connect a TV tuner. You can play back the broadcasts recorded, delete them or burn them on external media through this Menu
point.
Operation
Windows Media Center.
Help
3. Click on
Safety
Windows Media Center
Connecting
59
Play back DVD
You will play DVDs through this Menu point.
You will have the possibility of configuring the TV signal here, if
you have an external TV tuner available.
Online Media
Programmes
This library of programmes offers a listing of various online media.
You will call up content through the Internet, from the online
video library, through news portals to the music shop, by means
of the online media. An existing Internet connection is the requirement for the use of this function.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Appendix
Set up TV
60
Main menu
Sub-menu
Tasks
Settings
Adapt the Windows Media Center to your requirements and
needs here. For example, make the settings for the protection of
children here.
Stand by
You will not only close the Windows Media Center but you will
be able to put the whole operating system in stand-by through
this sub-menu. Pay attention that all applications have been already closed before putting the system into stand-by.
Burn CD/DVD
Call up your burning software to start a burning process through
this sub-menu
Synchronising
If you connect an external device, such as an MP3 player or a
digital camera; you will be able to synchronise the respective data
to an external device with the notebook through this sub-menu.
Extension set-up
You will be able to set up a Windows Media Center extension by
means of this sub-menu. You will be able to access the data on
your notebook by means of a cable or wireless network.
‘Only media’
You will switch to the full image of the Media Center by means of
this sub-menu.
Images + Videos
Library of images
All the images stored in your notebook will be located in the library of images. Start the playback in a slide show here.
Play back everything
Select ‘Play back everything’, to start the playback of a slide
show directly.
Video library
All the videos stored in your notebook will be located in its video
library.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Music library
All the music titles stored in your notebook will be located in the
music library. You will be able to start the selected playback of
an album, an artist or a selected title here.
Play back everything
You will start the playback of all the files stored in your music
library by means of this sub-menu.
Radio
You will have the possibility of listening to a radio broadcaster
and to administrate it, if you have external radio tuner hardware
available.
Search
Appendix
Help
You will be able to search for music titles, composers, artists,
albums, etc. in a targeted way by means of this sub-menu. The
search will start as soon as you have entered the first letters.
Connecting
Music
Sub-menu
Operation
Main menu
Safety
61
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
62
Installation of Software
Note
If your operating system is configured so that the installation procedure accepts only signed drivers (default) and software an information screen will
appear.
The software included in delivery is already pre-installed in the factory.
Attention!
You may find that during the installation procedure important files may be
changed or even cancelled. To avoid further problems in using older files after an installation, make sure you safeguard your hard disk. See page 71 for
further information regarding data backup.
How to Install your Software
Please follow the instruction of the software vendor. We will describe a typical installation.
Once you insert a CD, the installation menu is started automatically.
Note
If the automatic start does not work, it is likely that the so-called Autorun
function has been deactivated. Read the respective chapter in Windows
Help on how to activate this function.
An example for the manual installation without the autorun function:
1. Click on Start
.
2. Click on  All Programs.
3. Open the
Accessories program point.
4. Select the item
Run.
5. Now enter the letter of the CD-ROM drive followed by a colon and the program
name setup:
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
6. Click on "OK".
7. Follow the instruction given by the program.
Safety
Operation
Connecting
63
Software Uninstallation
In order to remove installed software from your All-In-One PC, follow the next steps:
2. Click on
.
Help
1. Click on Start
Control Panel.
3. Then select the
Programs option.
Appendix
4. Select the respective program, start the uninstallation and follow the instructions
on the screen.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
64
Windows Activation
Microsoft is committed to the protection of intellectual property rights and the reduction
of software piracy. Therefore Windows® 7 contains software-based product activation
technology. Your copy of Windows® 7 has already been activated for your All-In-One PC.
Product activation is needed if some components of your All-In-One PC have been replaced or you use a non-authorised BIOS. If necessary you can activate Windows® 7 as
often as requested.
You will probably need to activate Windows® 7 by telephone even if Internet Activation is
available. This is due to the pre-activated SLP version which runs with a special Product-ID.
However, activation needs your unique Product ID which can be found on the Certificate
of Authenticity sticker on your All-In-One PC housing. When you call, please inform your
agent that you are running an OEM-(SLP) version of the software.
Product Activation on Your All-In-One PC
In few cases it may still be required to activate Windows® 7. If an activation via the internet
is acknowledged with an error message you should perform the following steps.
1. Please select the telephone activation and click until the related screen appears.
2. Now click on change product key. A new window appears. Enter the product key.
This is located on the Certificate of Authenticity (COA), on the computer’s casing.
3. Acknowledge your entry and follow the instructions on the screen. Notify your Microsoft consultant, if necessary, that you have an OEM license in connection with
your All-In-One PC.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
In the BIOS set up (your All-In-One PC’s Basic Configuration) you have a number of parameter settings available for your All-In-One PC. For example, you can change the operating mode of the interfaces, security features or power management.
The All-In-One PC is factory pre-set to guarantee optimum operation. Please only modify the parameters if this is absolutely essential and if you are familiar with the configuration possibilities.
Safety
BIOS Setup
Connecting
65
Appendix
Help
You can only execute the configuration program when starting the system. If the All-In®
One PC has already been started exit Windows and reboot. Prior to rebooting the All-InOne PC press the key "DEL" and keep it pressed until the message "Entering Setup" appears.
Operation
Execution of the BIOS Setup
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
66
BullGuard Internet Security
The BullGuard Internet Security Package is a combination of the currently most up-to-date
All-In-One PC security technologies on the market and thus offers you 24-hour optimum
protection.
BullGuard is already installed, so that additional installation will not be necessary. If you
nevertheless have to carry out an installation (e.g. after system restoration), you will find
the software package on the application/support disc supplied with the machine.
BullGuard Internet Security consists of the following security components:

Antivirus
The centrepiece of any serious All-In-One PC security application, the Antivirus application screens your e-mails, and scans your hard drives for viruses and malware.
The BullGuard Antivirus combines the highest update frequency in the business
with a no-nonsense user-interface.

Antispyware*
BullGuard Antispyware protects your All-In-One PC from all known kinds of spyware and adware by searching and cleaning files, registry keys, processes and cookies, protecting you from identity theft and the loss of personal information.

Spamfilter*
The BullGuard Spamfilter will protect you from annoying spam and potentially
costly phishing attempts - a key tool in keeping your Inbox free from unsolicited
mail.

Backup*
Backing up your files has never been easier with both local and online backup. Not
only can you customise the size of your online backup drive to suit your needs once uploaded, you can access these files from any computer connected to the
internet anywhere in the world!

Support*
BullGuard Support is a key component in all BullGuard products. Assistance with all
security related questions available to all users directly from the application. No
FAQ, no automated response – real people and live help.
*Information
The Antispyware, Spam filter, Backup and Support components will only
be released after the free registration and will be deactivated after the expiry
of 90 days.
Procure a BullGuard subscription through the internet link given on the next
page, in order to be able to continue to use this module.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
The BullGuard Internet Security Package will be updated with the most up-to-date virus
information for 90 days after the free registration.
Safety
67
Keep your password in a secure place.
The antivirus software will continue to run after the expiry of 90 days, but it will no longer
be updated, so that your All-In-One PC will not be protected against new viruses.
The purchase of various subscriptions through BullGuard is possible in order to always
receive the most up-to-date information and updates.
A subscription can be purchased on the internet and carried out without complications. An
additional release or the entering of a licence is not necessary. Neither changes nor additional settings will have to be made.
Operation
Note
Connecting
The registration window will only appear after your All-In-One PC has been restarted. You
can register by entering your email address.
The release will take place automatically after the purchase of a subscription.
Read the information about this on the internet at:
Help
https://www.bullguard.com/buy_new.aspx?
The operating system and anti-virus software are automatically updated
when the first online connection is made. These processes usually take a few
minutes, during which time the operating speed of the computer may be affected although this is only noticeable on initial start-up.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Appendix
Note
68
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Customer Service &
Self Help
Subject
Page
Data and System Security ............................................... 71
System Restore ............................................................... 72
Safety
Connecting
Chapter 4
Operation
69
FAQ – Frequently Asked Questions ................................. 76
Repairs
.......................................................................... 81
Appendix
Recycling and Disposal ................................................... 82
Help
Customer Service ............................................................. 77
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
70
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
The programs described below are part of your Windows operating system. You can find
additional information on these programs in the Windows Help file.
Please also read the notes on page 5.
Data Security
Safety
Data and System Security
Connecting
71
Maintenance Programs
Appendix
You can avoid some hardware and software errors with the help programs such as Disk
Defragmenter and Disk Cleanup. The help program System Information can also be
helpful as it gives you detailed information about your system configuration. You can also
find these programs in Accessories  System Tools too.
Help
This program is found in Accessories  System Tools within the Start menu. You should
make a backup disk with all your passwords and the operating system’s original configuration.
Operation
Back up data regularly on external media such as a CD-R or CD-RW. Windows offers Backup Status and Configuration.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
72
System Restore
Windows® 7 provides a useful function (System Restore) enabling the storage of the socalled Recovery points.
The system remembers the current configuration as a snapshot and returns to this, if necessary. The advantage is that an unsuccessful installation can be cancelled.
Recovery points are created automatically by the system, but they can also be set manually.
You can determine and configure yourself the maximum memory taken up by this. You
find this program in the program file under Accessories  System Tools.
We recommend setting a recovery point before installing new software or drivers. At this
point if the system does not run properly this recovery point should enable you to return
to a workable configuration without deleting newly created documents. In the next paragraph you will find your options for the repair of an incorrect installation.
Correction
Windows® 7 includes various functions ensuring that the All-In-One PC as well as the installed applications and devices work correctly.
These functions assist you in solving the problems which might occur by adding, deleting
or replacing files required for the functionality of the operating system, the applications
and devices. The recovery function or functions you use depend on the type of occurring
problem or error. For detailed information refer to the Windows help.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Windows Update is the online updating of Windows. Use Windows Update to download
elements such as security updates, important updates, the newest help files, drivers and
Internet products from the Internet.
The website is regularly augmented by new content, so that you can download the newest updates and error corrections at any time, to protect the All-In-One PC and guarantee
its functioning.
Windows Update will search through the All-In-One PC and provide a list of individual
updates especially for the configuration of your All-In-One PC.
Each update that Microsoft regards as important for the operation of the operating system,
programs or hardware components will be classified as an "important update" and automatically selected for installation for you.
Important updates will be provided to remove known problems and to protect the All-InOne PC against known security risks.
Carry out four simple steps, to download the updates needed and to keep your computer
on the current status of technology:
1. Click on Start
Safety
.
Help
2. Click on  All Programs.
3. Open
Connecting
Windows® Update
Operation
73
Windows Update.
5. Click on Add to select the desired update and to add it to the updates to be installed, while you are searching through the available updates in each category.
You can also read a complete description of each individual element by clicking on
the Read further Link.
6. Click on Check and install updates, when you have selected all the desired updates, and then click on Install now.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Appendix
4. Click on Check for update.
74
Windows Update Information for Data Security
Windows Update needs certain information about the respective All-In-One PC, so that a
suitable list with updates can be provided for you. This information will include the following:

Version number of the operating system

Version number of Internet Explorer

Version numbers of additional software programs

Plug & Play identification key of the hardware devices
Windows Update will stand up for the protection of your private data and will not record
your name, address, email address or other forms of personal data. The information collected will only be used during the time that you are visiting the website. It will also not be
stored.
The update can only be executed via the Internet. Ensure that you are on-line with your
All-In-One PC when downloading the updates.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
If your system is not functioning properly, you should use the Application Support Disc to
restore your system.
Limits of the Recovery

Changes made to the original configuration (RAS, Desktop or Internet settings) and
installed Software will be ignored by this Recovery and will not be reloaded.

Driver Updates or hardware installed by you will be ignored by this Recovery.
Carrying out a Restore
1. Remove any mass storage devices you may be using (memory cards, USB sticks,
etc.).
Safety
Connecting
System Restore
Operation
75
3. Press the corresponding key when you see the message "Press F11 to run recovery" or "Press F12 to run recovery".
After a few seconds, the message "Windows is loading files" will appear. Wait until the files are loaded. The "Power Recover" menu will then appear.
Help
2. Switch on the PC.
4. Select the language of the restoration menu.
6. Click on “Restore to HDD – no backup of user data”.
All data on the PC are irretrievably erased, restoring delivery condition.
7. Click on Next and follow the further instructions, which will appear on the screen,
to restore the delivery condition.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Appendix
5. Click on "Next".
76
FAQ – Frequently Asked Questions
When do I have to activate Windows?
Your software has been preactivated in the factory. An activation will
only be required, if ...
... several components are replaced by others.
... you install a new motherboard.
... a different BIOS version has been installed.
... you install the software to another computer.
Where shall I find the drivers necessary for my All-In-One PC?
The drivers are on the second partition of the hard drive, in the Drivers
and Tools directories.
What is the Windows activation?
Your operating instructions include a chapter about this subject.
How do I perform a data backup?
Make a backup and another backup of selected data to an external
medium (CD-R), to familiarise yourself with the technique.
A backup is unsuitable if you are not able to recover the data, the
medium (CD-R, CD-RW) is defective or no longer available.
Do I still have to install the enclosed CDs/DVDs?
No. Basically all programs are already preinstalled. The disks are only
intended as backup copies.
When is the recovery of the factory setting recommended?
This method should be chosen as the last resort. Read chapter “System Restore” on page 72 concerning the alternatives possible.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Troubleshooting
Errors can have simple causes, but sometimes they are caused by faulty equipment. We
would like to give you some ideas to solve common problems. Should these instructions
not lead to success, please feel free to call us.
Safety
Customer Service
Connecting
77

Check power points, power cable and all power switches.

Switch off the All-In-One PC and check all cable connections. Check the connections to peripherals. Do not exchange cables, even though they may look similar.
The polarity in those cables may be different. When it is confirmed that the computer has power and all connections are correct, turn the computer on again.
Frequent use of the programs Disk Defragmenter and Disk Cleanup will help you to
avoid problems with your operating
system.
Help
Visibly check all cables and connections. Should all lights be off, check whether all equipment is supplied with power.
Operation
Localise the Cause
Appendix
The tool "System Information", available in the program folder "System Tools" is also
very useful.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
78
Errors and Possible Causes
The monitor is blank.

Confirm that the system is not in stand-by mode. Press any key on the keyboard to
test this out.
Wrong Date and Time:

Click the clock on the taskbar and correct the date and time.
After a system restart a new drive letter is assigned to the cards in the card slots.

This can happen, when the card reader re-initialises the slots during a system start.
New IDs might be assigned, which can lead to new drive letters for some cards.
No data can be accessed from the optical drive.

Check whether the disc is inserted correctly.

Is the optical drive displayed in Windows Explorer? If so, test another disc.
The mouse does not work.

Check if the USB receiver is correctly plugged in.

Is the mouse functioning in another application program? Is the mouse deactivated
in "Device Manager"

Are the batteries exhausted? Insert new batteries of the same type.
There is not enough room on the HDD.

Audio or video recordings need a great deal of memory (between 1 and 2
GB/hour). Safeguard files that you do not need on external media, such as
DVD/CD-Rs or hard drives or other external media e.g. the MEDION hard drive
HDDrive 2go.
The All-In-One PC does not start up.

If all cable connections are correct, then try to reset the power supply of the All-InOne PC. Set the power switch at the rear of the All-In-One PC to position 0 (OFF).
Now press down the main switch at the front of the All-In-One PC for 10 seconds.
Wait 5 more seconds and the restart the All-In-One PC.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
If the suggestions in the above section have not solved your problem, please contact the
service hotline and we will attempt to help you solve the problem. Before you contact the
Technology Centre, however, please have the following information available:

How is your computer configured?

What additional peripherals do you use?

What messages, if any, appear on your screen?

What software were you using when the error occurred?

What steps have you already undertaken to solve the problem?

Have you upgraded or removed drivers or hardware?

Can you manually repeat the problem?

If you have been given a customer number previously, please quote this.
Safety
Connecting
Additional Support
Operation
79
However, often the software drivers for individual components are updated from time to
time. This is a regular process provided by the manufacturer to mend possible compatibility problems that may occur with components (e.g., programs or hardware) that were not
tested at the time of your All-In-One PC’s manufacture. Driver updates and the latest information on your product are available on the Internet.
Visit Medion on the Web at www.medion.com.au
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Appendix
This All-In-One PC has been extensively tested in our laboratories with a large number of
compatible devices. It fulfils all required standards and complies with the standard "Designed for Windows", which certifies utmost compatibility.
Help
Driver Support
80
Transporting the All-In-One PC
Please observe the following guidelines when transporting the All-In-One PC:

To avoid damage during transport, store the All-In-One PC in its original packaging.
Cleaning and Care
The lifetime of the All-In-One PC can be extended by taking the following measures:
Warning!
There are no user-serviceable or user-cleanable parts inside the All-In-One
PC housing.

Before cleaning, always disconnect the mains cable and all connection cables.
Clean the All-In-One PC with a damp, lint-free cloth.

Dust can clog the air vents, leading to overheating and malfunctioning. Check at
regular intervals (about every 3 months) that all air vents permit sufficient air circulation. Use a vacuum cleaner to keep the air vents clear of dust. If your device regularly sucks in a great deal of dust, we also recommend that the interior of the All-InOne PC housing be cleaned by a professional.

Do not use solvents, caustic or volatile cleansers.

Before cleaning, always remove the power plug and all connecting cables. Clean
the All-In-One PC with a damp, lint-free cloth. Do not use any solvents, corrosive or
gaseous cleaning agents. Do not use CD-ROM cleaning discs or similar products
that clean the lens of the laser to clean your CD- /DVD-drive.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Contact you the MEDION Australia Helpdesk on 1300 884 987 when...

Liquid has got into the All-In-One PC

The All-In-One PC does not operate properly

The All-In-One PC is dropped or the housing is damaged.
Notes for Service Engineers
Before opening the housing, disconnect the All-In-One PC from all power sources
and remove any connecting cables. If the All-In-One PC has not been disconnected
from the power outlet before being opened, there is a danger to life through electric shock. There is also a risk of damage to the components.

Internal components of the All-In-One PC may be damaged by electrostatic discharge (ESD). Carry out system upgrades and changes in an ESD-protected workshop.
If no such workshop is available, wear an antistatic wrist strap or touch a highly
conductive metal object. Medion can repair damage sustained by inappropriate
handling for a fee.

Use only original spare parts.
Safety
Appendix

Connecting
Please contact the MEDION Australia Helpdesk on 1300 884 987 if you have any problems
with your All-In-One PC. ONLY have repairs completed by our authorised service centre.
Operation
Repairs
Help
81
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
82
Notes on Laser Radiation:

Laser devices of Laser Class 1 to Laser Class 3b may be used in the All-In-One PC.
Where the All-In-One PC housing remains closed, the device meets the requirements of Laser Class 1.

By opening the All-In-One PC housing you will gain access to laser devices of up to
Laser Class 3b.
When removing and/or opening laser devices, the following guidelines must be observed:

The CD-ROM-/CDRW-/DVD-drives installed contain no user-serviceable parts.

Only the manufacturer should perform repairs to the CD-ROM-/CDRW-/DVD-drives.

Do not look into the laser beam, even while wearing optical protection.

Do not allow yourself to be exposed to the laser beam. Avoid exposure of the eyes
or skin to direct or stray radiation.
Recycling and Disposal
Device
At the end of its life, the appliance must not be disposed of in household rubbish. Enquire
about the options for environmentally-friendly disposal
Batteries
Do not dispose of used batteries in the household rubbish! They must be deposited at a
collection point for used batteries.
Packaging
To avoid damage during transport, the All-In-One PC is stored in protective packaging.
The packaging is produced mostly from materials which can be disposed of in an environmentally friendly manner and therefore can be professionally recycled.
Should you have any questions concerning the disposal please contact your dealer or our
service.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Chapter 5
Appendix
Safety
Page
Standards ....................................................................... 85
Appendix
Help
Index ................................................................................ 90
Operation
Subject
Connecting
83
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
84
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Standards
Safety
85
EN 55022
Information technology equipment - Radio disturbance characteristics - Limits and methods of measurement.
EN 55024
Information technology equipment - Immunity characteristics - Limits and methods of measurement.
EN 61000-3-2
Limits - Limits for harmonic current emissions (equipment input current up to and including 16 A per
phase).
EN 61000-3-3
Limits - Limitation of voltage fluctuations and flicker in
low-voltage supply systems for equipment with a
rated current up to 16 A.
The antenna connection of the TV tuner is in compliance with EN55013, EN55020.
Operation
This All-In-One PC meets the following requirements for standards of electromagnetic
compatibility and electrical safety:
Help
Electromagnetic Compatibility
Connecting
This All-In-One PC meets the requirements of the following standards:
Electrical safety requirements according to the following standards:
EN 60950-1
Safety of information technology equipment.
Ergonomics
Ergonomic requirements according to the following standards:
DIN EN ISO
Ergonomic requirements for office work with display
devices:
9241-3
Part 3: Requirements for visual displays
9241-4
Part 4: Requirements for keyboards
9241-8
Part 8: Requirements for colour representation
9241-9
Part 9: Input devices except keyboards
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Appendix
Electrical Safety
86
Noise Emission
Requirements for noise emission according to the measurement procedure in accordance
with the following standard:
ISO 7779
(ISO 9296)
Acoustics. Measurement of airborne noise emitted by
information technology and telecommunications
equipment.
This All-In-One PC fulfils the requirements of noise emissions according to ISO 7779 with
following values:
Operating Mode
Max. Sound power level LWAd (B/A) (declared according to ISO 9296)
Idling
4.8
Operating
5.2
Max. Sound pressure level LpAm (dB/A)
(declared according to ISO 9296)
At bystander position Idling
40
St bystander position Operating
47
This device fulfils the basis requirements and the relevant regulation of the Ecodesign
Guideline 2009/125/EG (Commission Regulation 1275/2008).
ISO 13406-2 Class II
Active matrix LCDs (TFT) with a resolution of 1920 x 1080 pixels which are in turn composed of three sub-pixels each (red, green, blue), contain about
6.2 million addressable transistors. Because of this very high number of transistors and
their extremely complex production process occasionally defective or incorrectly addressed pixels or sub-pixels may occur.
There have been several attempts in the past to define the acceptable number of defective
pixels. But this can be difficult and varies widely between different manufacturers.
We, therefore, adhere to the clear and strict requirements of ISO 13406-2,
class II, for the warranty handling of all TFT display products. These requirements are
summarised below.
Within ISO-standard 13406-2 the general requirements regarding pixel defects are defined.
Pixel defects are classified into three failure types and four failure classes. Each individual
pixel is made up of three sub-pixels in the primary colours (red, green, blue).
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Connecting
Pixel structure
Safety
87
Rows
Blue
Green
Red
Type 1:
A constantly lit pixel (a bright, white spot), even though it is not addressed. A white
pixel is caused when all three sub-pixel are lit.

Type 2:
A pixel that does not light up (dark, black spot), although it is addressed

Type 3:
Abnormal or defective red, green or blue sub-pixels.
(E.g. constantly lit with half the brightness, one colour is not shining, blinking or
flickering, but not belonging to Type 1 or 2 Pixel Failures)
In addition: A cluster of type 3 (= 2 or more defective sub-pixels in an array of 5 x 5 pixel).
A cluster is an array of 5 x 5 pixel (15 x 5 sub-pixel).
Help

Operation
Types of Pixel Failures:
ISO 13406-2, Class II
Type 1
Type 2
Type 3
Cluster
Type 1,
Type 2
Cluster
Type 3
1024 x 768
2
2
4
0
2
1280 x 800
3
3
6
0
3
1280 x 854
3
3
6
0
3
1280 x 1024
3
3
7
0
3
1366 x 768
3
3
7
0
3
1400 x 1050
3
3
8
0
3
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Appendix
Resolution
88
Example:
A 17” (approx. 43 cm) - SXGA-display consists of 1280 horizontal and 1024 vertical picture
dots (pixel), which amounts to a total of 1,31 million pixels. Based on one million pixels
this translates into a factor of about 1.31.
Class II type failure consequently allows for three defects each of type 1 and type 2 and 7
defects of type 3 and 3 cluster of type 3.
These cases are normally not covered by warranty.
If the number of failures exceeds the figures of any category mentioned above then this
may be covered by the warranty.
Information about the Regulatory Compliance
according to R&TTE
The following remote equipment is supplied with this All-In-One PC:

Wireless Keyboard

Wireless Mouse

Remote Control

USB Receiver

Built-In Wireless LAN Module
Due to the capacity of the built-in wireless LAN solution (> 100 mW) the device may only
be used within buildings in France.
Currently none of the other EU-countries have any restrictions. For use in other countries
please obtain information about the applicable regulations locally.
The company declares herewith that these devices are in agreement with the fundamental
requirements and the other relevant terms of the 1999/5/EG Guideline. Complete declarations of conformity are available under www.medion.com/conformity.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.

Consult the dealer or an experienced technician for help.
Safety
Connecting
FCC Compliance Statement
Operation
89
Help
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment. Shielded interface cables, if any,
must be used in order to comply with the emission limits.
Making Copies of this Manual
Appendix
This manual contains information protected by law. All rights reserved. Duplicating this
information in mechanical, electronic, or any other form, without the written approval by
the manufacturer, is prohibited by copyright law.
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
90
Index
A All Programs ....................................... 23
Ambient Temperature......................... 11
Autorun .............................................. 62
B Control Panel ................................. 29
On-Screen Keyboard ...................... 30
Operation ...................................... 29
Sreen Resolution ............................ 30
Driver Support ................................... 79
E Battery Treatment ................................. 6
BIOS Setup ......................................... 65
BullGuard Internet Security................. 66
C Cabling ............................................... 13
Card Reader ........................................ 41
Care .................................................... 80
Carrying out a restore ......................... 75
CD-ROM ............................................. 37
Cleaning ............................................. 80
Cleaning Agents ................................. 80
Cleansers ............................................ 29
Connecting......................................... 13
Microphone .................................... 20
Power Supply ................................. 20
PS/2 Devices ................................... 18
Sound Source /Audio Input ............ 18
Speakers/Audio Output .................. 19
USB Devices .................................... 14
Control Panel
Disk Management ........................... 35
Control Panel...................................... 58
Customer Service ................................ 77
D Data and System Security ................... 71
Data Security ........................................ 5
Directories .......................................... 36
Disc Drive ........................................... 37
Discs
Removing Blocked Discs ................. 38
Display
Appearance and Personalisation ..... 31
Cleaning ......................................... 29
After Sales Support
TEL: 1 300 884 987
Electromagnetic Compatibility ........... 85
Emergency Ejection of a Blocked Disc 38
Ergonomics .................................. 11, 85
Errors and Possible Causes ................. 78
F FAQ.................................................... 76
FCC Compliance Statement ............... 89
G Getting Started .................................. 21
H Hard Drive.......................................... 35
Hotline ............................................... 79
I Icons .................................................. 23
Included with Your PC ......................... 9
Installation of Software ...................... 62
ISO 13406-2 Class II ........................... 86
K Keyboard ........................................... 33
Keys ............................................... 33
Multimedia Functions .................... 34
L LAN Connection ................................. 18
Laser Radiation ................................... 82
License Agreement ............................. 22
Localise the Cause .............................. 77
WEB Support: www.medion.com.au
Maintenance....................................... 80
Maintenance Programs ....................... 71
Microphone Amplification .................. 44
Mouse ................................................ 32
Multimedia Functions ......................... 34
S T O On/Off Switch .................................... 21
On-Screen Keyboard ........................... 30
Operation
Keyboard ........................................ 33
Mouse ............................................ 32
Operational Safety
Data Security .................................... 5
Ambient Temperature ..................... 11
Cabling ........................................... 13
Connecting ..................................... 13
Set-up Location............................... 10
Optical Disc Drive ............................... 37
P Power On ........................................... 21
Program Bar ....................................... 23
R R&TTE ................................................ 88
Recycling and Disposal ....................... 82
Remote Control .................................. 47
After Sales Support
TEL: 1 300 884 987
Transporting ...................................... 80
Troubleshooting .......................... 52, 77
TV Tuner Card .................................... 46
U USB Port ............................................. 45
W Webcam............................................. 44
Windows Activation ........................... 64
Windows Media Center ...................... 59
®
Windows 7
User Account Control ..................... 57
Control Panel ................................. 58
Getting Started............................... 56
Help and Support........................... 55
News .............................................. 53
Windows® Desktop ............................. 23
®
Windows Update............................... 73
Wireless Keyboard & Mouse
Installation ..................................... 15
Wireless LAN ...................................... 51
WEB Support: www.medion.com.au
Help
Network ............................................. 50
LAN Access Point ............................. 51
Troubleshooting ............................. 52
What is a Network? ......................... 50
Wireless LAN ................................... 51
Noise Emission .................................... 86
Appendix
N Service Engineers ............................... 81
Set-up Location .................................. 10
Software ............................................ 53
Software Uninstallation ...................... 63
Sound System .................................... 42
Standards
Electrical Safety .............................. 85
Electromagnetic Compatibility ....... 85
FCC Compliance Statement ........... 89
Start Button ....................................... 23
System Restore ................................... 72
Safety
Repairs ............................................... 81
Connecting
M Operation
91
92
After Sales Support
TEL: 1 300 884 987
WEB Support: www.medion.com.au
Download PDF