Miller Electric | Bobcat 250 | imagenes/miller bobcat 250

Bobcat Series
Issued April 2010 • Index No. ED/4.4
™
Quick
Specs
Gas, LP or Diesel Engine-Driven
Welder/AC Generator
Industrial Applications
Processes
Output Range
225
250
250 EFI
Maintenance
Repair
Farm/Ranch Applications
Fabrication
Structural Steel Work
Use as a Stand-Alone
Generator
Stick (SMAW)
Flux Cored (FCAW)
MIG (GMAW)
DC TIG (GTAW)
Non-Critical AC TIG (GTAW)
Air Carbon Arc (CAC-A) Cutting
and Gouging (3/16 in carbons)
Air Plasma Cutting and Gouging
with optional Spectrum models
Optional Battery Charger
AC TIG/Stick
DC Stick/TIG
FCAW/MIG
50 – 225 A
50 – 210 A
19 – 28 V
40 – 250 A
40 – 250 A
17 – 28 V
40 – 275 A
40 – 275 A
17 – 28 V
Generator Power Output Rated at 104˚F (40˚C)
225/250 Peak: 11,000 W
225/250 Continuous: 9,500 W
250 EFI Peak: 12,000 W
250 EFI Continuous: 10,500 W
Accu-Rated™–
Not Inflated
Generator Power
The Power of Blue .
®
Reliable Bobcat engine-driven
welding generators are the industry
standard for quality and value.
Multiprocess weld output, strong
generator power, and most important
— rated #1 in reliability, make the
Bobcat the welding industry’s most
popular choice. Bulletproof inside
and out.
Bobcat 250 models only
See Choose the Right Gas Engine Drive
on page 2 for more information.
NEW! Electronic Fuel
Injection (EFI) Benefits
vs Carburetor Models
• 12% to 27% better fuel economy!
• Reduced emissions — 33% lower
HC+Nox levels and 27% lower CO!
(EPA 1000 Hour Certification)
• Easy starting in all climates with no
choke required
• Elimination of carburetor icing
• Better high-altitude performance
(electric fuel pump is recommended)
• EFI is more reliable when using
equipment infrequently
• 12,000 watts of generator power and
more weld output
Versatile AC and DC Stick/TIG plus Wire
capabilities provide quality welds on all
types of metals. DC is smooth and easy
to run while AC Stick is used when arc
blow occurs.
Note: AC TIG requires Dynasty 200 Series or
HF-251 (non-critical).
Accu-Rated™—Not Inflated Generator
Power. Miller’s Accu-Rated 11,000 watts
(12,000 with EFI) of usable peak power is
delivered for a minimum of 30 seconds.
See page 4 for more information.
Welding and generator power ratings are
at 104˚F (40˚C) — highest in its class to
ensure reliable performance.
Fuel capacity of 12 gallons means many
hours of run time before refueling.
Bobcat 250
(gas model) shown
Optional Bobcat 250 EFI Model with
12,000 Watts and More Weld Power!
Meter maintenance displays:
• Hour meter function and oil change interval
• Diesel: High coolant temperature shutdown,
low oil pressure shutdown and low fuel
shutdown — engine shuts down before
system runs out of fuel making restarts easy
The addition of the Bobcat’s Tri-Cor ™
Technology provides improved Stick arc
performance with 7018 electrodes.
Front panel fuel and sight gauges provide
convenient fuel level indication. Note: Diesel
engine will shut down before the system
runs out of fuel making restarts easy.
Welder/generator is warranted for 3 years, parts and labor.
Engine is warranted separately by the engine manufacturer.
Miller Electric Mfg. Co.
Equipment Sales US and Canada
Web Site
An Illinois Tool Works Company
1635 West Spencer Street
Appleton, WI 54914 USA
Phone: 866-931-9730
FAX: 800-637-2315
International Phone: 920-735-4554
International FAX: 920-735-4125
www.MillerWelds.com
Specifications
Model
Bobcat
225
Bobcat
250
(Subject to change without notice.)
Process
Amp/Volt
Ranges
Weld Output Rated
at 100% Duty Cycle
(at 104°F/40°C)*
CC/AC
TIG/Stick
50 – 225 A
225 A at 25 V
CC/DC
Stick/TIG
50 – 210 A
210 A at 25 V
CV/DC
MIG/FCAW
19 – 28 V
200 A at 20 V
CC/AC
CC/DC
Stick/TIG
40 – 100 A
60 – 140 A
80 – 200 A
100 – 250 A
Welding
Mode
CV/DC
MIG/FCAW
Sound Levels at
Rated Output,
7 m (23 ft)
Single-Phase
Generator Power
Net
Weight**
Peak: 11,000 watts
Continuous: 9,500 watts
120/240 VAC, 88/44 A, 60 Hz
75.5 dB
(100.5 Lwa)
H: 28 in (711 mm)
H: 33 in (838 mm)
to top of exhaust
W: 20 in (508 mm)
D: 45-1/2 in (1156 mm)
530 lb
(240 kg)
250 A at 25 V
(275 A at 25 V,
60% Duty Cycle)
Peak: 11,000 watts
Continuous: 9,500 watts
120/240 VAC, 88/44 A, 60 Hz
Kohler: 75.5 dB
(100.5 Lwa)
EFI Model
250 A at 28 V
275 A at 25 V
EFI Model
Peak: 12,000 watts
Continuous: 10,500 watts
Gas/LP Model:
H: 28 in (711 mm)
H: 33 in (838 mm)
to top of exhaust
W: 20 in (508 mm)
D: 45-1/2 in (1156 mm)
Diesel Model:
H: 30 in (762 mm)
H: 34-1/4 in (870 mm)
to top of exhaust
W: 20 in (508 mm)
D: 52 in (1321 mm)
Gas/LP
Model:
556 lb
(252 kg)
Diesel
Model:
700 lb
(318 kg)
Subaru: 76.5 dB
(101.5 Lwa)
Kubota: 80.5 dB
(105.5 Lwa)
250 A at 28 V
(275 A at 25 V,
60% Duty Cycle)
17 – 22 V
20 – 28 V
Dimensions
Note: Derate outputs up to 5% when using LP fuel. *Rated at sea level. **Net weight without fuel.
Certified to both Canadian and U.S. Standards for welding equipment available. See ordering information on back.
Engine Specifications
(Engines warranted separately by the engine manufacturer.)
Engine Brand/
Warranty
Horsepower (HP)
Type
Weld
Speed
Idle
Speed
Fuel
Capacity
Kohler:
3-year mfg.
23 HP (gas), 25 HP EFI,
25 HP (LP) at 3600 RPM
Twin-cylinder, 4-cycle overhead
valve, industrial air-cooled, gasoline*
(carburetor or EFI) or LP
3600
RPM
2300
RPM
Subaru:
3-year mfg.
23 HP at 3600 RPM
Twin-cylinder, 4-cycle overhead
valve, industrial air-cooled, gasoline*
3600
RPM
Kubota: 2-year
limited North
American mfg.
19 HP at 3600 RPM
3-cylinder, industrial liquid-cooled,
diesel
3600
RPM
Oil Capacity
Standard Shutdowns
12 gal
(45 L)
1.5 qt (1.4 L)
Low Oil Pressure
2300
RPM
12 gal
(45 L)
1.6 qt (1.5 L),
1.8 qt (1.75 L)
with filter
Low Oil Pressure
2450
RPM
12 gal
(45 L)
3.4 qt (3.2 L)
High Coolant Temperature/
Low Oil Pressure/Low Fuel
*Fuel stabilizer is recommended for gas engines that are used infrequently.
Choose the Right Gas Engine Drive
Product Description
Bobcat 225
Bobcat 250
Cost-effective multiprocess machine
primarily used for Stick is great for farm,
ranch, stand-alone generator, and
maintenance/repair operations.
Rugged engine drive is great for Stick and
Flux Cored welding and is designed for
maintenance/repair operations, construction,
farm, ranch and generator use.
Welding Performance
MIG— Wire (Solid/FCAW), Steel
Fair
MIG— Wire, Aluminum w/Spool Gun
Fair
TIG— DC, Steel
Good
TIG— AC, Aluminum w/H.F.*
Fair
Upgrade
Upgrade
Upgrade
Upgrade
Good
Upgrade
Upgrade
11,000 Watts/12,000 with EFI
Upgrade
Upgrade
Hours/Oil Change/Fuel
Good
Very Good
Fair/Good
Generator
Watts
11,000 Watts
Power While Welding
Fair/Good with voltage control set near
maximum
Good — easier to fine tune arc with voltage
control near maximum
Key Features
Maintenance Displays
Hours/Oil Change
EFI (Electronic Fuel Injection)
Not available
*High Frequency Arc Starter and Stabilizer.
2
Optional
Why Buy a Gas or Diesel Engine?
Gas Advantages
EFI Advantages (vs. Carburetor Models)
Diesel Advantages
• Lower product cost (by 50 – 70%)
• Smaller size and less weight
• Less expensive engine repairs
• Better warranties
• Easier cold weather starting
• 12 – 27% better fuel economy
• Reduced emissions (approx. 1/3 lower)
• Easy starting in all climates (no choke)
• Elimination of carburetor icing
• Better high altitude performance
• Uses 20–40% less fuel than carburetor gas
• 1-1/2 to 2-1/2 times the engine life
• Required on some job sites for safety
• Typically have longer maintenance intervals
• Convenient if other equipment is diesel
Gas Carburetor and Diesel Models
Gas EFI Models
FUEL CONSUMPTION
FUEL CONSUMPTION
2.00
2.00
Generator
Power
Weld
1.25
1.00
Weld
0.75
DIESEL
0.50
0
50
Generator Pwr
1.50
1.25
Weld
1.00
0.75
0.50
Idle 2200 RPM
0.25
0.00
1.75
GAS
1.50
U.S. GAL/HR
U.S. GAL/HR
1.75
Idle 2200 RPM
0.25
100
150
200
250
0.00
300
0
50
0
2
4
6
8
100
150
200
250
300
10
12
WELD AMPERES AT 100% DUTY CYCLE
WELD AMPERES AT 100% DUTY CYCLE
10
0
12
2
4
6
8
POWER KVA AT 100% DUTY CYCLE
POWER KVA AT 100% DUTY CYCLE
FUEL CONSUMPTION DATA
HOW EFI CAN SAVE YOU MONEY
• 12-gallon fuel capacity.
• On a typical job using 1/8-in 7018 electrodes (125 A, 20% duty cycle) expect about
20 hrs (gas) or 24 hrs (diesel) of operation.
• Welding at 150 A, 40% duty cycle uses approximately:
3/4 gallon per hour — about 16 hrs of operation (gas) or
1/2 gallon per hour — about 20 hrs of operation (diesel).
• Under a continuous load of 4000 watts of generator power, the Bobcat would run
for about 14 hrs (gas) or about 17 hrs of operation (diesel).
• 120 V, 20 A continuous load (25 hrs/week, $3/gal): fuel cost carbureted = $75,
fuel cost EFI = $54.75. Difference of approximately $20 x 50 weeks = $1,000 per
year savings with EFI!
• Running 1/8 in 7018 electrodes at 20% duty cycle, EFI will save $405 per year!
• Running .045 diameter wire at 40% duty cycle, EFI will save $502 per year!
Function Guide
1
1. Maintenance Displays provide fuel level (250 models only), engine
hours and oil change interval information. Diesel model adds high
coolant temperature and low oil pressure shutdowns.
2
3
2. Weld Process Selector Switch makes choosing between Stick, Wire
and TIG processes easy. Switch also automatically changes polarity
with process selection to make sure the machine is easy to set with
little effort or knowledge.
4
6
3. Coarse Range Control
225 Model — Three Stick/TIG and one Wire range are available for
output control. Stick/TIG ranges are designed to electrode diameters
(3/32, 1/8 and 5/32 in) making these models very easy to set.
250 Model — Four Stick/TIG and two Wire ranges are available for
output control. Stick/TIG ranges are designed to electrode diameters
(3/32, 1/8, 5/32 and 3/16 in) making these models very easy to set.
7
4. Fine Adjust Control makes it easy to fine tune amperage within a
coarse range. Set control above 7 for best power while welding and to
10 for generator-only use.
5
ELECTRODE
5. Engine Control Switch is used to start the engine and then select
between Auto Idle and High Speed Lock. Diesel model can be locked in
idle for low-speed starting.
6. Engine Choke Control (Gas/LP models) is used for easy engine starting.
Note: No choke necessary on EFI models.
Glow Plugs (Diesel model) assist in cold weather starting.
7. 120 VAC and 240 VAC Covered Receptacles with Circuit Breakers
meet/exceed OSHA/CSA requirements for job site safety
(optional 120 VAC GFCI receptacles available).
Note: For matching plug, order #119 172.
3
The Bobcat Generator Power Advantage
TYPICAL EQUIPMENT POWER USAGE
Accu-Rated – Not Inflated Generator Power
™
Bobcats will easily start and run the following equipment:
Miller’s Accu-Rated™ 11,000 watts (12,000 with EFI) of usable peak power
is delivered for a minimum of 30 seconds. Accu-Rated means peak power
is usable for maximum generator loads such as plasma cutting,
Millermatic® MIG welders and motor starting. Accu-Rated peak power beats
the competition’s very short-duration peak or surge power. Use your peak
power, it’s more than a number.
Bobcat
Smooth Power – Not Spike Power
Competitor
AC POWER VOLTS
Revolutionary ten-degree skewed-rotor design
optimizes generator performance for smoother
power—not spiked power found with other
brands. Better power — better performance.
300
264
250
216
200
150
132
125
108
100
150
100
50
25
0
0
Waveform Comparison
Starting Watts
Barn Cleaner (5 HP)
11,600
3000
Silo Unloader (5 HP)
12,200
4300
Running Watts
Portable Conveyor (1/2 HP)
3400
1000
Milker (5 HP)
10,500
2800
Hand Drill (1/2 inch)
600
600
Circular Saw (8-1/4 inch)
1400
1400
Air Compressor (1-1/2 HP)
8200
2200
Flood Lights (Vapor)
1250
1000
Refrigerator/Freezer
2200
700
Sump Pump
1300
800
Millermatic® 212 Auto-Set™
MIG Welder (230 V)
6500
6500
Spectrum® 625 X-TREME™
(30 A, 230 V, 1/2 in cut)
6900
6900
To select a generator that has enough power output in watts, add the watts for
the items you want to simultaneously run. Tools and appliances with induction
motors may require 3 – 7 times the listed wattage when starting. All data listed
is approximate — check your tool/appliance for specific wattage requirements.
SIMULTANEOUS WELDING AND POWER
GENERATOR POWER CURVE
Weld Current
in Amperes
Total Power
in Watts
120 V Full kVA
Receptacle
Amperes
240 V Full kVA
Receptacle
Amperes
75
0
11,000
88*
44*
50
90
8000
66*
33
125
5200
43*
21
180
3500
29*
14
250
2200
18
9
0
20
40
60
80
100
120
140
160
180
200
220
AC POWER AMPS AT 120 V
0
10
20
30
40
50
60
70
80
90
100
110
AC POWER AMPS AT 240 V
Tools and motors are designed to operate within 10% of 120/240 VAC. The
Bobcat’s power generator provides strong power while keeping the voltage
within 10% of 120/240 VAC. This increases tool/motor performance and life.
The Bobcat
Competitive
Advantage
• 68% of service technicians, managers
and owners, recommend the Bobcat
over the competition.
1
ENGINE
3
STATOR
*50 A, 120/240 VAC receptacle. See Owner’s Manual for additional information.
• 98% of current owners are “satisfied
to very satisfied” with the Bobcat*.
Technician Recommendations
Hot air
directed out
and upward
Cool air in
for engine
For example, if you’re welding at 125 amps you also have 5200 watts
available for powering lights or tools (either 43 amps from the 120 volt
full kVA receptacle or 21 amps from the 240 volt full kVA receptacle).
Bob
Oth
ers
cat
68%
Make deadlines, not excuses.
2
Cool air
in for
generator
Directed airflow improves cooling for long engine and component life.
4
Equipment
*Based on an independent survey of
thousands of Bobcat owners.
1 The fully enclosed case design virtually eliminates hot air
recirculation when machine is mounted in tight spots.
2 Louver-directed air flow keeps the temperature of internal parts
cool for maximum performance and extended life.
3 Self-cooling stator barrel
completely encloses and protects
its generator from the dirtiest
and harshest environments.
All ratings are tested at 104˚F (40˚C)
to maintain tough work schedules, even
in hot weather.
Genuine Miller Options
*Available as factory option. See ordering information on back page.
GFCI Protection* #195 496 Field
Ground Fault Circuit Interruptors are required
on some construction sites. Kit contains
two GFCI 120 VAC duplex receptacles.
(240 VAC GFCI receptacle not required).
LP Gas*
Liquid withdrawal with vaporizer and
regulator. Does not include tanks, brackets,
or hose from tank to regulator.
Spark Arrestor #043 579 Field
Mandatory when operating on California
grasslands, brush or forest-covered land,
and all National Forests. For other areas,
check your state and local laws.
Remote Oil
Drain/Filter Kits
Note: Requires LP Tank Mounting Assembly #195 329.
Electric Fuel Pump* #195 214 Field
For gas models at high altitude. Improves
engine starting and high-output performance.
Battery Charger*
Built-in system for industrial battery
charging. Charges 12, 24 and 36 V batteries
while not welding or using generator power.
Note: AC weld output not available with this option.
FA-7.5 Flame Arrestor
Fuel Cap (Gasoline Red)
#042 632 Field
Lockable for added
protection.
Rear Mounted (shown)
#300 106 Field. For Kohler
#300 417 Field. For Subaru
Oil can be drained from rear of machine.
Front/Chassis Truck Mounted
#300 236 Field. For Kohler
#300 418 Field. For Subaru
Oil can be drained from the front of the
machine or below the truck, mounted on
the chassis.
Makes servicing easy when engine drive is
mounted in tight spots.
Female
Receptacle
Adapter Cord, Full KVA #300 517 Field
NEMA 14-50P to NEMA 6-50R. Adapts
engine drive 120/240 V plug to common
Millermatic® and Spectrum® 240 V plug.
Full KVA Plug Kit
#119 172 Field
120/240 VAC, 50 amp plug
(NEMA 14-50P) to fit full
KVA receptacle.
Order the following from Miller Service Parts.
Engine Tune-Up Kits
#230 015 Field. Kohler CH 23 (Gas)
#246 115 Field. Kohler ECH 730 (EFI Gas)
#180 096 Field. Kohler CH 20 (LP)
and CH 730 (LP)
#199 062 Field. Subaru EH 65
#206 421 Field. Kubota D722
Tune-up kits include spark plugs
(Gas/LP models) and engine filters.
TIG Adapter with Extension #195 350 Field
Extension with Power Cable Adapter
45V11. Required for scratch start TIG
welding with Bobcats.
Genuine Miller Accessories
All-Purpose
Running Gear
#300 396 Gas/LP,
with inner tubes
#300 477 Gas/LP,
with Never Flat™ tires
Includes two heavy-duty 15 in tires, two
8 in rubber swivel casters and a heavy-duty
handle. Recommended for all surfaces and
applications, and is easy to move around
the job site.
All-Purpose Running Gear with
Protective Cage
#300 428 Gas/LP, with inner tubes
#300 478 Gas/LP, with Never Flat™ tires
Running gear and rugged cage with cable
holders protects your investment and is
easy to move around flat surfaces.
All-Terrain Running Gear EZ
#300 572 Gas, with inner tubes
#300 574 Gas, with Never Flat™ tires
Includes two heavy-duty 15 in tires, two 10 in
pneumatic tires with innertubes and a rugged
handle to provide maximum maneuverability.
All-Terrain
Running Gear EZ
with Protective Cage
#300 573 Gas,
with inner tubes
#300 575 Gas,
with Never Flat™ tires
Running gear and rugged cage with cable
holders protects your investment and is
easy to move around the jobsite.
Note: Not for use with Gas Cylinder Mounting
Assembly or LP Tank Mounting Assembly.
Protective Cage
with Cable Holders
#195 331 Gas/LP
#300 052 Diesel
Rugged cage with
cable holders protects
your investment. Can be used with running
gear, Gas Cylinder Mounting Assembly, LP
Tank Mounting Assembly, or with trailer.
Gas Cylinder
Mounting Assembly
#195 330 Gas/Diesel
Designed for use with
All-Purpose Running
Gear, Protective Cage,
or by itself. Includes
base tray with bottle bracket, vertical
support rack and safety chain.
Note: Not recommended for diesel models when
equipped with All-Purpose Running Gear. Not for use
with LP Tank Mounting Assembly or All-Terrain
Running Gears. Not recommended for use with
Protective Cover.
LP Tank Mounting
Assembly
#195 329 LP
Designed for use with
All-Purpose Running
Gear, Protective Cage,
or by itself. Includes bracket and clamp to
mount 33 and 43 lb tanks horizontally, and
hose with fittings to converter.
Note: Not for use with Gas Cylinder Mounting
Assembly or All-Terrain Running Gears. Not
recommended for use with Protective Cover.
Note: Not for use with Gas Cylinder Mounting
Assembly or LP Tank Mounting Assembly.
5
Genuine Miller Accessories
(continued)
Protective Covers
TIG (GTAW) Welding
Dynasty® 200 Series
For premium portable AC/DC
TIG arc quality. See Lit. Index
No. AD/4.8.
#195 333 shown
#195 333 For Gas models without
Protective Cage or Running Gear.
#195 529 For Gas models with Protective
Cage and/or Running Gear.
Note: Protective Cage side rail support brackets
cannot be used with cover.
#195 334 For Diesel model without
Protective Cage or Running Gear.
Heavy-duty, water-resistant and mildewresistant covers protect and maintain the
finish of the welder.
Plasma Cutting
SuitCase® X-TREME™ 8VS Wire Feeder
#951 181
SuitCase® X-TREME™ 12VS Wire Feeder
#951 184
Lightweight, portable, voltage-sensing
wire feeders include secondary contactor
and gas valve. See Lit. Index No. M/6.41.
Spoolmatic® 30A
Spool Gun #130 831
Rated 200 amps at
100% duty cycle.
Air-cooled, 1-lb spool
gun for aluminum MIG. Includes 30 ft
(9.1 m) cable assembly. See Lit. Index No.
M/1.73. WC-115A required for hookup.
HF-251 Series #042 388
HF-251D-1, 115 VAC
High-frequency arc starter
and stabilizer. See Accessory
Lit. Index No. AY/5.0. Requires
Secondary Contactor.
Secondary Contactor #041 969 Field
Required to use HF-251D-1.
Trailers and Hitches
WC-115A Control #137 546-01-1
With contactor. Use with Spoolmatic 30A.
MIG/Flux Cored Welding
Millermatic 140
Auto-Set and 212
Auto-Set shown.
Millermatic® 140 Auto-Set™ #907 335
See Lit. Index No. DC/12.42
Millermatic® 180 Auto-Set™ #907 312
See Lit. Index No. DC/12.44
Millermatic® 212 Auto-Set™ #907 405
See Lit. Index No. DC/12.46
The Millermatic line of MIG welders are
complete arc welding power source, wire
feeder and gun packages designed for
portability and ease of use.
Note: The Millermatic machines can be operated
utilizing generator power.
6
SGA 100C Control #043 857
SGA with contactor required to connect
Spoolmate 3035 to CV engine drive.
Includes 10 ft (3 m) 115 VAC power cable
and plug, 6 ft (1.8 m) interconnecting cable,
and 5 ft (1.5 m) gas hose.
Heavy-Duty Barrel for Spoolmate™ 3035
#195 375
Use for demanding applications, rated at
200 A, 60% duty cycle.
HWY-1000 Trailer
#195 013
A 1000 lb (454 kg) capacity highway trailer
with welded steel tubing frame, heavy-duty
axle with roller bearing hubs and leaf-spring
suspension. The HWY-1000 comes with
jack stand, 2 in (50 mm) ball hitch, fenders
and lights.
Note: Trailer is shipped unassembled.
Cable Tree #195 023
Provides an area to conveniently wrap
weld cables and extension cords on the
HWY-1000 trailer.
Lunette Eye 2-1/2 in (64 mm) #043 824
Mounting Specifications
G
A
4 Holes
Engine End
Spectrum® 375 X-TREME™ #907 339
See Lit. Index No. PC/9.2.
Spectrum® 625 X-TREME™
#907 404 12 ft (3.7 m) torch
#907 404-01-1 20 ft (6.1 m) torch
See Lit. Index No. PC/9.6.
The Spectrum 375 X-TREME and 625
X-TREME come complete with protective
X-CASE™ (not shown).
Spoolmate™ 3035
Spool Gun #195 016
Use with SGA 100C
Control and HeavyDuty Barrel. Spool gun
for aluminum and other wires. 4 in spools;
.023–.035 in (0.6– 0.9 mm) aluminum, steel
and stainless steel. Rated at 150 amps, 60%
duty cycle with 20 ft (6 m) cable assembly.
B
C
D
E
F
A. 20 in (508 mm)
B. 16-1/2 in (419 mm)
C. 1-3/4 in (44 mm)
D. 6-1/16 in (154 mm)
E. 32-3/4 in (832 mm)
F. 45-3/8 in (1153 mm) (Gas)
52 in (1321 mm) (Diesel)
G. 13/32 in (10 mm) diameter
Height: (to top of exhaust)
33 in (838 mm) (Gas)
34-1/4 in (870 mm) (Diesel)
Width: 20 in (508 mm)
Depth: 45-7/8 in (1164 mm) (Gas)
52-1/2 in (1334 mm) (Diesel)
Typical Installations for Bobcat 250
Stick (SMAW) Basic Equipment
Stick Electrode
• Four-position range switch provides fine amperage control
for typical electrode diameters (3/32, 1/8, 5/32 and 3/16 in).
• AC weld output for good arc quality with iron powder
electrodes without fighting magnetic arc blow.
• Strong auxiliary power while welding — for example, if you
are welding at 250 amps the Bobcat delivers 2200 watts of
power to run tools, lights etc.
Work
Flux-Cored (FCAW) Basic Equipment
SuitCase® X-TREME™ 8VS
#951 181
SuitCase® X-TREME™ 12VS
#951 184
• 275 amps at 25 volts, 60% duty cycle (250 amps at 28 volts,
100% duty cycle). Strong output allows higher travel speeds
and deposition rates than competitive machines.
• High voltage output ratings (28 volts at 250 amps) help to
compensate for voltage drop across long weld cables.
Gun
X-TREME 8VS/
X-TREME 12VS
Feeder
Volt-Sensing Lead
Work
Gun
MIG (GMAW) Basic Equipment
SuitCase® X-TREME™ 8VS
#951 181
#951 184
SuitCase® X-TREME™ 12VS
#907 335
Millermatic® 140 Auto-Set™
Millermatic® 180 Auto-Set™
#907 312
Millermatic® 212 Auto-Set™
#907 405
• Use .035 in solid wire with 75/25 argon mixed gas for
welding down to 16 gauge steel.
• Use .045 solid wire with a minimum of 80% argon gas
for spray transfer on 1/8 in and thicker material
(flat and horizontal position).
• Millermatic machines utilize generator power.
X-TREME 8VS/
X-TREME 12VS
Feeder
Volt-Sensing Lead
Work
Gun
Millermatic
Work
Aluminum MIG (GMAW) Basic Equipment
Spoolmate™ 3035
SGA 100C
#195 016
#043 857
Spoolmatic 30A
#130 831
WC-115A Control
#137 546-01-1
• Excellent results from 1/8 –1/2 in thick fillet welds.
®
Spoolmate 3035/
Spoolmatic 30A
SGA 100C/WC-115A
with Contactor
Work
Plasma Basic Equipment
• Spectrum® machines utilize generator power.
• Quality cuts with an optional Spectrum® plasma cutter.
• Replace heavy oxy-fuel cylinders with a lightweight, fast
and versatile Spectrum® plasma cutter.
• Most plasma units require a separate air source.
Cutting Torch
Spectrum
Plasma
Cutter
Work Leads
Work
TIG (GTAW) Basic Equipment
TIG Adapter w/Extension
#195 350
• Required for Scratch Start TIG welding
Dynasty® 200 Series
HF251D-1
#042 388
Secondary Contactor
#041 969
RMLS-14 Switch
#129 337
• Excellent DC TIG capabilities
• Non-critical AC TIG welding (no remote amperage control
available on the Bobcat)
HF-251D-1
w/Contactor
TIG
Torch
Work
7
Ordering Information
Equipment and Options
Stock No.
Description
Bobcat™ 225
(23 HP Kohler)
#907 209
#907 209-01-1
#907 209-01-3
#907 209-01-4
#907 210
#907 210-01-1
#907 210-01-2
#907 211
#907 211-01-1
#907 211-01-3
#907 211-01-4
#907 211-01-8
#907 211-02-1
#907 211-03-1
#907 212
#907 212-01-1
#907 212-01-3
#907 212-01-4
#907 212-01-5
#907 212-02-1
#907 450
#907 450-00-1
#907 450-00-2
#907 450-00-3
#907 450-00-4
#907 213
#907 213-01-1
#907 213-02-1
#907 213-01-3
#195 496
#195 214
#042 632
#043 579
Base machine, CC/CV, AC/DC 11,000 watts
With GFCI Receptacles
With CSA Approval
With No Battery
Base machine, CC/CV, AC/DC 11,000 watts
With GFCI Receptacles
With CSA Approval
Base machine, CC/CV, AC/DC 11,000 watts
With GFCI Receptacles
With CSA Approval
With Electric Fuel Pump for High Altitude
With No Battery
With Battery Charger and GFCI Receptacles
With LP Gas, CSA Approval and GFCI Receptacles
Base machine, CC/CV, AC/DC 11,000 watts
With GFCI Receptacles
With CSA Approval
With Electric Fuel Pump for High Altitude
With No Battery
With Battery Charger and GFCI Receptacles
Base machine, CC/CV, AC/DC 12,000 watts
With GFCI Receptacles
With CSA Approval
With Electric Fuel Pump for High Altitude
With No Battery
Base machine, CC/CV, AC/DC 11,000 watts
With GFCI Receptacles
With Battery Charger and GFCI Receptacles
With No Battery (International)
Field
Field. For gas models at high altitude
Field. Gas models
Field
Field. See page 5
Field
Field
Field. See page 5
Field. Required for Scratch Start TIG welding w/Bobcats. (Order from Miller Service Parts)
Bobcat™ 225
(23 HP Subaru)
Bobcat™ 250
(23 HP Gas, 25 HP LP Kohler)
Bobcat™ 250
(23 HP Subaru)
Bobcat™ 250 EFI
(Electronic Fuel Injection)
(25 HP Kohler)
Bobcat™ 250 Diesel
(19 HP Kubota)
GFCI Protection
Electric Fuel Pump
Flame Arrestor Fuel Cap
Spark Arrestor
Remote Oil Drain and Filter Kit
Adapter Cord, Full KVA
Full KVA Plug
Engine Tune-Up Kits
TIG Adapter with Extension
Accessories
All-Purpose Running Gear
All-Purpose Running Gear
with Protective Cage
All-Terrain Running Gear EZ
All-Terrain Running Gear EZ
with Protective Cage
Protective Cage
with Cable Holders
Gas Cylinder Mounting Assembly
LP Tank Mounting Assembly
Protective Covers
Spectrum® Plasma Cutters
Millermatic® Series MIG Welders
SuitCase® Portable Wire Feeders
Spoolmatic® 30A Spool Gun
WC-115A Control
Dynasty® 200 Series TIG Welders
HF-251D-1
Secondary Contactor
HWY -1000 Trailer
Cable Tree
Lunette Eye 2-1/2 in (64 mm)
#300 517
#119 172
#195 350
#300 396
#300 477
#300 428
#300 478
#300 572
#300 574
#300 573
#300 575
#195 331
#300 052
#195 330
#195 329
#130 831
#137 546-01-1
#042 388
#041 969
#195 013
#195 023
#043 824
Gas/LP models, with inner tubes
Gas/LP models, with Never Flat™ tires
Gas/LP models, with inner tubes
Gas/LP models, with Never Flat™ tires
Gas models, with inner tubes. Not for use with Gas Cylinder or LP Tank Mounting Assembly
Gas models, with Never Flat™ tires. Not for use w/Gas Cylinder or LP Tank Mounting Assembly
Gas models, with inner tubes. Not for use w/Gas Cylinder or LP Tank Mounting Assembly
Gas models, with Never Flat™ tires. Not for use w/Gas Cylinder or LP Tank Mounting Assembly
Gas/LP models
Diesel model
Gas/Diesel models. Not for use with LP Tank Mounting Assembly or All-Terrain RGs
LP models. Not for use with Gas Cylinder Mounting Assembly or All-Terrain RGs
See page 6
See page 6
See page 6
See page 6
Requires WC-115A Control. See Lit. Index No. M/1.73
See Lit. Index No. M/1.73
See Lit. Index No. AD/4.8
115 VAC. Requires Secondary Contactor
Date:
Total Quoted Price:
Distributed by:
Litho in USA
Qty.
Price
Download PDF