Barnstead | 48000 | Specifications | Barnstead 48000 Specifications

Type 47900 & 48000
Furnaces
OPERATION MANUAL
Series 1165, 1166 & 1205
Single Setpoint Models
F47910, F47910-26, F47910-33, F47914, F47915, F48010, F48010-26,
F48010-33, F48014, F48015, F48015-60, F48018
Single Setpoint Models
with OTP
F47920, F47920-26, F47920-33, F47924, F47925, F48020, F48020-26,
F48020-33, F48024, F48025, F48025-60, F48028
8 Segment Programmable
Models with OTP
F47920-80, F47920-26-80, F47920-33-80, F47924-80, F47925-80,
F48020-80, F48020-26-80, F48020-33-80, F48024-80, F48025-80,
F48025-60-80, F48028-80
4 X 16 Segment
Programmable Models
with OTP
F47950, F47950-26, F47950-33, F47954, F47955, F48050, F48050-26,
F48050-33, F48055, F48055-60, F48058
LT1165X1 • 3/1/02
Table of Contents
Safety Information ..............................................................................................................................................3
Alert Signals..................................................................................................................................................3
Warnings ......................................................................................................................................................3
Introduction..........................................................................................................................................................5
Intended Use ................................................................................................................................................5
General Usage..............................................................................................................................................5
Principles of Operation ................................................................................................................................5
General Specifications ........................................................................................................................................6
Type F47900 Models ....................................................................................................................................6
Type F48000 Models ....................................................................................................................................6
Environmental Conditions ............................................................................................................................7
Declaration of Conformity ............................................................................................................................7
Unpacking ..........................................................................................................................................................8
Installation ..........................................................................................................................................................9
Site Selection................................................................................................................................................9
Electrical Connections ..................................................................................................................................9
Operation, All Models ........................................................................................................................................10
Power Switch ..............................................................................................................................................10
Cycle Light ..................................................................................................................................................10
Door Safety Switch ....................................................................................................................................10
Single Setpoint Models & Single Setpoint Models with OTP ..........................................................................11
Single Ramp & Dwell ........................................................................................................................................16
8 Segment & 4 x 16 Segment Programmable Models with OTP ....................................................................19
Furnace Loading ..............................................................................................................................................39
Preventative Maintenance ................................................................................................................................40
General Cleaning Instructions ....................................................................................................................40
Troubleshooting ................................................................................................................................................41
Maintenance and Servicing ..............................................................................................................................44
To Replace a Heating Element ..................................................................................................................44
To Replace a Chromel/Alumel Thermocouple ............................................................................................45
To Replace Door Switches (Micro-Switch) ................................................................................................46
To Realign Door Switches (Micro-Switch) ..................................................................................................47
To Replace the Controller ..........................................................................................................................48
Replacement Parts............................................................................................................................................49
Single Setpoint Models ..............................................................................................................................49
Single Setpoint Models with OTP ..............................................................................................................49
8 Segment Programmable Models with OTP ............................................................................................50
4 x 16 Segment Programmable Models with OTP ....................................................................................50
Wiring Diagrams................................................................................................................................................51
Ordering Procedures ........................................................................................................................................59
One Year Limited Warranty ..............................................................................................................................60
2
Safety Information
Alert Signals
Warning
Warnings alert you to a possibility of
personal injury.
Caution
Cautions alert you to a possibility of
damage to the equipment.
Note
Notes alert you to pertinent facts and
conditions.
Hot Surface
Hot surfaces alert you to the possibility
of personal injury if you come in contact
with a surface during use or for a period
of time after use.
Your Barnstead Thermolyne Type 47900 or
48000 Furnace has been designed with function,
reliability and safety in mind. It is your responsibility to install it in conformance with local electrical codes. For safe operation, please pay attention to the alert signals throughout the manual.
This manual contains important operating and
safety information. You must carefully read and
understand the contents of this manual prior to
the use of this furnace.
Warnings
To avoid electrical shock, this furnace must:
1. Use a properly grounded electrical outlet
of correct voltage and current handling
capacity.
2.
Be disconnected from the power supply
prior to maintenance and servicing.
3.
Have the door switch operating properly.
To avoid personal injury:
1. Do not use in the presence of flammable
or combustible materials; fire or explosion may result. This device contains
components which may ignite such material.
2.
Caution: Hot Surface - Avoid Contact. To
avoid burns, do not touch the exterior or
interior surfaces of this furnace during
use or for a period of time after use.
3.
Always wear safety glasses or a safety
shield and high temperature gloves when
loading or unloading the furnace. Long
sleeved, fire retardant clothing and a fire
retardant apron is also recommended.
4.
Refer servicing to qualified personnel.
3
SAFETY INFORMATION
Warning
Refer Servicing to qualified personnel.
Warning
This warning is presented for compliance with
California Proposition 65 and other regulatory agencies and only applies to the insulation in this product. This product contains refractory ceramic, refractory ceramic fiber or fiberglass insulation, which can
produce respirable dust or fibers during disassembly.
Dust or fibers can cause irritation and can aggravate
pre-existing respiratory diseases. Refractory ceramic
and refractory ceramic fibers (after reaching 1000°C)
contain crystalline silica, which can cause lung damage (silicosis). The International Agency for
Research on Cancer (IARC) has classified refractory
ceramic fiber and fiberglass as possibly carcinogenic
(Group 2B), and crystalline silica as carcinogenic to
humans (Group 1).
The insulating materials can be located in the door,
the hearth collar, in the chamber of the product or
under the hot plate top. Tests performed by the manufacturer indicate that there is no risk of exposure to
dust or respirable fibers resulting from operation of
this product under normal conditions. However, there
may be a risk of exposure to respirable dust or fibers
when repairing or maintaining the insulating materials, or when otherwise disturbing them in a manner
which causes release of dust or fibers. By using
proper handling procedures and protective equipment you can work safely with these insulating
materials and minimize any exposure. Refer to the
appropriate Material Safety Data Sheets (MSDS) for
information regarding proper handling and recommended protective equipment. For additional MSDS
copies, or additional information concerning the handling of refractory ceramic products, please contact
the Customer Service Department at Barnstead
International at 1-800-553-0039.
4
Introduction
Intended Use
Caution
Do not exceed operating temperatures
shown in “General Specifications.”
Exceeding these limits will result in
severely reduced element life.
The Type F47900 and F48000 furnaces are
general purpose laboratory and heat treating
furnaces. For optimum element life,
Barnstead International recommends observing these temperature ranges: from 100°C
(212°F) to 1093°C (2000°F) continuous use
or from 1093°C (2000°F) to 1200C (2192°F)
for intermittent use. Continuous use is operating the furnace for more than 3 hours and
intermittent use is operating the furnace for
less than 3 hours.
All furnaces consist of: 1) a vented heating
chamber; 2) a temperature controller; and 3)
a door safety switch for operator safety.
General Usage
Do not use this product for anything other
than its intended usage.
Principles of Operation
The furnace chamber is heated by open coil
electric resistance elements and is insulated
with ceramic fiber insulation. The controller is
located under the furnace chamber and is
well insulated from the heat generated in the
furnace chamber. A door safety switch
removes power to the heating elements
whenever the furnace door is opened. The
temperature is controlled by one of three
types of controllers.
5
General Specifications
Type F47900 Models
Dimensions in Inches (cm):
Chamber:
5 (12.7) W x 4 (10.2) H x 6 (15.2) D
Overall:
11.25 (28.6) W x 18 (45.7) H x 15.5 (39.4) D
Weight:
37 lb. (16.8 kg)
Electrical Ratings:
Volts:
220-240
100
120
Amps:
4.2
7.5
8.3
Watts:
1000
750
1000
Frequency: 50/60
50/60
50/60
Phase:
1
1
1
Temperature:
Operating Range: 2000°F (1093°C) continuous
2192°F (1200°C) intermittent
Type F48000 Models
Dimensions in Inches (cm):
Chamber:
7 (17.8) W x 5 (12.7) H x 10 (25.4) D
Overall:
13.25 (33.7) W x 19 (48.3) H x 19.5 (49.5) D
Weight:
56 lb. (25.4 kg) (all models except -33)
58 lb. (26.3 kg) (-33 models only)
Electrical Ratings:
Volts:
220-240
Amps:
7.5
Watts:
1800
Frequency: 50/60
Phase:
1
120
14.5
1500
50/60
1
208
15
1560
50/60
1
* -33 models only
Temperature:
Operating Range:
6
2000°F (1093°C) continuous
2192°F (1200°C) intermittent
100
14.5
1450
50/60
1
220-240*
6.5*
1560*
50/60*
1*
GENERAL SPECIFICATIONS
Environmental Conditions
Operating: 17°C to 27°C; 20% to 80% relative humidity, non-condensing. Installation
Category II (overvoltage) in accordance with IEC 664. Pollution degree 2 in
accordance with IEC 664.
Altitude Limit: 2,000 meters.
Storage: -25°C to 65°C; 20% to 80% relative humidity
Declaration of Conformity
Barnstead International hereby declares under its sole responsibility that this product conforms with the technical requirements of the following standards (220-240 Volt Models
Only):
EMC:
Safety:
EN 50081-1
EN 50082-2
EN 61010-1
EN 61010-2-010
Generic Emissions Standard
Generic Immunity Standard
Safety Requirements for Electrical Equipment
for Measurement, Control and Laboratory Use;
Part I: General Requirements
Part II: Particular Requirements for
Laboratory Equipment for the Heating of Materials
per the provisions of the Low Voltage Directive 73/23/EEC, as amended by 93/68/EEC.
The authorized representative located within the European Community is:
Electrothermal Engineering Ltd.
419 Sutton Road
Southend On Sea
Essex SS2 5PH
United Kingdom
Copies of the Declaration of Conformity are available upon request.
7
Unpacking
8
1.
Visually check for any physical damage to the shipping container.
2.
Inspect the equipment surfaces that
are adjacent to any damaged area.
3.
Open the furnace door and remove
the packing material from inside the
furnace chamber.
4.
Vacuum the chamber prior to use to
remove the insulation dust due to
shipment. (The Type 48000 furnace is
supplied with one ceramic shelf.)
5.
Retain the original packaging material
if reshipment is foreseen or required.
Installation
Site Selection
Caution
Be sure ambient temperature does not
exceed 40°C (104°F). The recommended
ambient temperature is 17°C - 27°C.
Ambients above this level may result in
damage to the controller.
Caution
Allow at least six inches of space
between the furnace and any combustible
surface. This permits the heat from the
furnace case to escape so as not to create a possible fire hazard.
Install furnace on a sturdy surface and allow
adequate space for ventilation.
Electrical Connections
The electrical ratings are located on the specification plate on the back of the furnace.
Consult Barnstead International if your electrical service is different than those listed on the
specification plate. Be sure the front power
switch is in the OFF position before connecting the furnace to your electrical supply.
Warning
To avoid electrical shock, this furnace
must always use a properly grounded
outlet of correct voltage and current handling capacity.
9
Operation, All Models
Warning
To avoid personal injury do not use in the
presence of flammable or combustible
chemicals; fire or explosion may result.
This device contains components which
may ignite such materials.
Hot Surface
Caution: Avoid Contact. To avoid burns,
this furnace must not be touched on the
exterior or interior surfaces during use or
for a period of time after use.
Power Switch
Both the ON/OFF power switch and the digital
display will illuminate when power is switched
ON. The furnace will begin to heat to its controller's current setpoint. (See the instructions
for your type of controller for information on
checking and setting the setpoint.)
Cycle Light
The amber cycle light will illuminate whenever
the power is being applied to the heating elements. The cycle light will turn on and off as
the furnace reaches the setpoint.
Door Safety Switch
Warning
Always wear safety glasses or a safety
shield and high temperature gloves when
loading or unloading the furnace. Long
sleeved, fire retardant clothing and a fire
retardant apron is also recommended.
Warning
To avoid electrical shock, the door safety
switch must be operating properly.
10
The door safety switch removes power from
the heating elements when the door is
opened. Open and close the door a few
times; note that the amber CYCLE light will
switch off when the door is opened. If this
condition is not true, consult the
Troubleshooting section before proceeding.
This check must be done when the furnace is
heating and the cycle light is illuminated.
Single Setpoint Models &
Single Setpoint Models w/OTP
Output 2
Output 1
Temperature
Display
Manual
Display
Window
MAN
PAGE
Button
SCROLL
Button
DOWN ARROW
Button
UP ARROW
Button
Single Setpoint Models
The single setpoint model furnace controller
is a single setpoint controller which provides a
single digital display to indicate the current
chamber temperature or setpoint temperature.
This temperature controller features sensor
break protection and self-tuning capability.
The single setpoint model w/ OTP furnace
controller is a single setpoint controller which
provides a single digital display to indicate the
current chamber temperature or setpoint temperature. This temperature controller features
sensor break protection, self-tuning capability
and over temperature protection (OTP) with
an additional OTP relay device.
Basic Operation
When the controller is turned ON it will perform a short self-test and then display the
measured value (process value) in the HOME
DISPLAY.
Buttons and Indicators
Note
If at any time you want to return to the
HOME DISPLAY, simultaneously press
the PAGE and SCROLL buttons.
OP1 (Output 1): Illuminates when the logic
output is ON.
OP2 (Output 2): Illuminates when the relay
output is ON (will go out during an alarm situation).
PAGE button: Allows you to select a new list
of parameters.
SCROLL button: Allows you to select a
parameter within a list of parameters.
11
SINGLE SETPOINT MODELS & SINGLE SETPOINT MODELS
W/OTP
DOWN button: Allows you to decrease a value.
UP button: Allows you to increase a value.
To View or Change the Setpoint
To view the setpoint, press and release the UP or
DOWN buttons. If you want to change the setpoint, continue pressing until the desired setpoint
value is displayed and then release the button. A
few seconds after the button is released, the controller will accept the new value and revert to the
HOME DISPLAY.
To View the Display Units
From the HOME DISPLAY press the SCROLL
button. The display will show the temperature
units in °C/F/K and then return to the HOME DISPLAY. (Call Customer Service if you require a different temperature unit.)
To View the % Output Power
From the HOME DISPLAY press the SCROLL
button twice. Press and release the UP or DOWN
button to view the % output power. This value is a
read-only value and cannot be changed.
Controller Parameters
Home display
°C: Temperature units in Celsius. Temperature
units can not be changed without entering the
configuration. Contact Customer Service if a different temperature unit is required.
12
SINGLE SETPOINT MODELS & SINGLE SETPOINT MODELS
W/OTP
OP: % output power demand.
IdHi: Deviation high alarm.
Al List
IdHi: Deviation high alarm.
Atun List
tunE: One-shot autotune enable.
Pid List
Pb: Proportional band (in display units).
ti: Integral time in seconds.
td: Derivative time in seconds.
ACCS List Code: Access code (Code needed to enter or change the other configuration
parameters which are not normally accessible.) Not accessable.
Alarms
The controller will flash an alarm message in
the home display if an alarm condition is
detected.
Note
The following alarm messages are factory default settings and may vary if you
have changed the configuration of your
controller:
IDHi: = 50°C
2FSH = 1225°C
2FSH: Measured value full scale high alarm.
IdHi: Measured value deviation high alarm.
S.br: Sensor break: check that sensor is connected correctly.
L.br: Loop break: check that the heating circuits are working properly.
13
SINGLE SETPOINT MODELS & SINGLE SETPOINT MODELS
W/OTP
Ld.F: Heater Circuit fault: indication of either
an open or short solid sate relay, a blown
fuse, missing supply or open circuit heater.
Sensor Break Protection
This controller provides sensor break protection in the event the thermocouple opens. If
an open thermocouple condition occurs, the
digital display will blink “S.br” and the power
to the heating element will be shut OFF
(Cycle light will extinguish).
Over-Temperature Protection
(OTP)
The OTP will be in effect during any alarm
condition when the temperature of the furnace
has deviated beyond the limit. The “Deviation
High” alarm is the only alarm value which can
be changed. To change it, press the SCROLL
button until “IdHi” appears on the display.
Press the UP or DOWN button to select the
OTP value you desire. We recommend a
value of 20° above your working temperature
to provide protection for your workload.
In addition to over-temperature protection,
units containing a single setpoint controller
w/OTP feature a mechanical OTP relay
device which disconnects power from the elements in an alarm condition (only in furnaces
with OTP relay). See models listed on front
page.
14
SINGLE SETPOINT MODELS & SINGLE SETPOINT MODELS
W/OTP
Tuning
Note
Furnace must be at ambient
temperature before starting a tune.
Note
Tune has completed when “tunE”
stops flashing on display.
This controller incorporates a self-tuning feature which determines the optimum control
parameters for the best temperature accuracy
with your load and setpoint. Use this feature
the first time you use your furnace and each
time you change either your setpoint or the
type of load you are heating.
Barnstead|Thermolyne recommends you use
this feature to provide the best temperature
accuracy the controller can attain. To use the
tuning feature:
1. Adjust the setpoint to your desired
value.
2.
Press the PAGE button until display
reads, “Atun.”
3.
Press the SCROLL button. Display
will read, “tunE.”
4.
Press the UP or DOWN button to
select, “on.”
5.
Simultaneously press the PAGE and
SCROLL buttons to return to the
HOME DISPLAY. The display will
alternately flash between “tunE” and
the HOME DISPLAY while tuning is in
progress.
6.
The controller will then turn the heating on and off to induce an oscillation.
When the measured value reaches
the required setpoint the first cycle will
end.
7.
Tuning will be complete after two
oscillation cycles and then the tuner
will turn itself off.
8.
Normal control function will resume
after the controller calculates tuning
parameters.
15
Single Ramp & Dwell
Note
These instructions are used with the Single Setpoint models with OTP only
(See models listed on front page).
Functions
This type of controller has single ramp and dwell
programming capabilities. The Ramp and Dwell
can be configured to five different modes.
1.
Mode 1 (Opt. 1) is a Ramp (if needed) to
the Setpoint temperature, a Dwell, and
then a cool down.
2.
Mode 2 (Opt. 2) is the same as mode 1,
except the controller continues to heat at
the Setpoint after the Dwell has completed. (This mode does not cool down.)
3.
Mode 3 (Opt. 3) is the same as mode 1,
except the Dwell time includes the Ramp
(if needed).
4.
Mode 4 (Opt. 4) is the same as mode 2,
except the Dwell time includes the Ramp
(if needed).
5.
Mode 5 (Opt. 5) is a Dwell (delay time)
before the controller Ramps (if needed)
to the Setpoint temperature.
Mode 1 (Opt. 1)
Mode 2 (Opt. 2)
Mode 3 (Opt. 3)
Setting Variables
•
The Manual or Automatic modes can be
set by changing “m-A” variable to “mAn”
or “Auto.” (The Manual mode will keep
the controller from heating without setting
the Setpoint temperature below the
Actual temeperature. The Automatic
mode will allow the controller to heat to
the Setpoint temperature. (The controller
should be left in the Automatic mode
except when programming.)
•
A program mode can be set by changing
the “tm.OP” variable to “Opt. 1, Opt. 2,
Opt. 3, Opt. 4, or Opt. 5.
Mode 4 (Opt. 4)
Mode 5 (Opt. 5)
16
SINGLE RAMP & DWELL CONTROLLER
•
A Ramp rate may be set by changing the
“SPrr” variable to a value. The Ramp rate
units are in degrees per minute.
•
The Dwell time can be set by changing the
“dwEll” variable to the desired value. Dwell
time units are in minutes.
•
The program Status can be set by changing
the “StAt” variable to “run” or “oFF.” This
variable will start or stop the program.
Program Setup
Note
The program must be stopped and
the controller must be displaying the
actual temperature before beginning
the Setup.
1.
Press the SCROLL button until “m-A” is displayed, then set to “mAn” with the UP or
DOWN buttons.
2.
Press the PAGE button once, set the desired
Setpoint temperature with the UP or DOWN
buttons.
3.
Press the PAGE button until the “SP” is displayed.
4.
Press the SCROLL button once, “SPrr”
(Ramp Rate) will be displayed, set the
desired Ramp rate with the UP or DOWN
buttons, if the ramp to setpoint feature is
needed. If the Ramp rate is not needed,
then set to “OFF” with the UP or DOWN buttons.
5.
Press the SCROLL button once, “tm.OP”
(Ramp & Dwell mode) will be displayed,
select the desired mode with the UP or
DOWN buttons. (Opt. 1, Opt. 2, Opt. 3, Opt.
4, Opt. 5)
6.
Press the SCROLL button once, “dwEll” will
be displayed, set the desired Dwell time with
the UP or DOWN buttons. (Dwell in minutes.)
7.
Press the PAGE button until the Actual tem17
perature is displayed.
SINGLE RAMP & DWELL CONTROLLER
Running the Program
1.
Press the SCROLL button until “StAt”
is displayed, set to “run” with the UP
or DOWN buttons.
2.
Press the PAGE button to display
Actual temperature.
Stopping the Program
Press the SCROLL button until “StAt” is displayed, set to “oFF” with the UP or DOWN
buttons.
Clearing the Flashing End
Press the PAGE and SCROLL buttons at the
same time.
Switching from Manual Mode
to Auto Mode
Press the SCROLL button until “m-A” is displayed. Press the UP or DOWN buttons to
set to “Auto.” Press PAGE button to display
Actual temperature.
Verifying a Running Program
Press the SCROLL button until “StAt” is displayed. The display will show “run” if the program is running, or “oFF” if it is not running.
Press the PAGE button to display Actual temperature.
18
8 Segment & 4x16 Segment
Programmable Models w/OTP
Note
The controller will return to the HOME
DISPLAY if left idle for more than a few
seconds.
Note
Once the desired parameter has been
selected, depressing either the UP or
DOWN button will change the parameter
value. In all cases, the value shown on
the display is the current working value of
that parameter.
AUTO/MAN
Button
Output 1
Display
Window
Upper
Display
Lower
Display
RUN/HOLD
Button
UP ARROW
Button
PAGE
Button
SCROLL
Button
DOWN ARROW
Button
The 8 segment programmable controller
consists of a microprocessor based threemode PID (Proportional, Integral, Derivative),
programmable temperature controller with
over-temperature protection and appropriate
output switching devices to control the furnace. The digital readout continuously displays chamber (upper display) and setpoint
(lower display) temperatures unless the
SCROLL or PAGE button is depressed. The
programmable controller can be used as a
single setpoint controller or as a programmable controller. The 8 segment digital model
enables eight segments of programming.
The 4x16 segment programmable controller
consists of a microprocessor based threemode PID (Proportional, Integral, Derivative),
programmable temperature controller with
over-temperature protection and appropriate
output switching devices to control the furnace. The digital readout continuously displays chamber (upper display) and setpoint
(lower display) temperatures unless the
SCROLL or PAGE button is depressed. The
programmable controller can be used as a
single setpoint controller or as a programmable controller. The 4 program controller has
four 16 segment programs.
Basic Operation
When the controller is turned ON, it will perform a short self-test and then change to the
HOME DISPLAY. The HOME DISPLAY shows
the measured temperature (process value) in
the upper display and the desired value (setpoint) in the lower display.
4x16 & 8 Segment Programmable Models with OTP
19
8 SEGMENT & 4X16 SEGMENT PROGRAMMABLE MODELS
W/OTP
To Change the Setpoint
If you want to change the setpoint, press the
UP or DOWN button until the desired setpoint
value is displayed in the lower display and
then release the button.
To View Display Units
From the HOME DISPLAY press the SCROLL
button. The display will briefly show the temperature units in °C/F/K and then return to the
HOME DISPLAY. (If you require a different
temperature unit call Barnstead|Thermolyne
Customer Service.)
To View the % Output Power
From the HOME DISPLAY press the SCROLL
button twice. This value is a read-only value
and cannot be changed.
Buttons and Indicators
OP1 (Output 1): illuminates when the heating
output of the temperature controller is on.
AUTO/MAN: (Auto/Manual Mode): when the
controller is in the automatic mode the output
automatically adjusts to keep the temperature
or process value at the setpoint. The “AUTO”
light will illuminate. The manual mode has
been disabled through factory configuration.
Call Customer Service for further information.
RUN/HOLD (Run/Hold button):
•
Starts a program when pressed
once—RUN light illuminates.
20
8 SEGMENT & 4X16 SEGMENT PROGRAMMABLE MODELS
W/OTP
•
Holds a program when pressed again—
HOLD light illuminates.
•
Cancels hold and continues running
when pressed again—HOLD light is off
and RUN light illuminates.
•
Exits a program when the button is held
down for two seconds—RUN and HOLD
lights are off.
•
At the end of a program the RUN light
will flash.
•
During holdback the HOLD light will flash.
PAGE button: allows you to choose a parameter
from a list of parameters.
SCROLL button: allows you to choose a parameter within a list of parameters.
UP button: allows you to increase the value in
the lower display.
DOWN button: allows you to decrease the value
in the lower display.
Controller Parameters
Home Display
°C: measured temperature in Celsius.
Temperature units can not be changed without
entering the configuration. Contact Customer
Service if a different temperature unit is required.
OP: % output power demand; displayed in lower
display (cannot be changed).
C.id: Controller identification number.
21
8 SEGMENT & 4X16 SEGMENT PROGRAMMABLE MODELS
W/OTP
PrG: Program number (displayed when a program is running; 4x16 programmable models
only.)
IdHi: Deviation High Alarm
tunE: One-shot autotune enable.
run LiSt (Program Run List)
PrG: Currently running program (only used on
4x16 programmable models)
StAt: Displays the program status [OFF, run
(running active program), hoLd (program on
hold), HbAc (waiting for process to catch up),
End (program completed)] in the lower display. The controller will default to “OFF.”
FASt: Fast run through program (no/YES).
The controller will default to “no.”
SEG.d: Flash active segment type in the
lower display of the home display (no/YES).
The controller will default to “no.”
ProG LiSt (Program Edit List)
PrG.n: Press the UP or DOWN ARROW to
select the program number (program number
will be displayed in lower display on 4x16 programmable models only.)
Hb: Press the UP or DOWN ARROW to
select the holdback type [OFF (disables holdback), Lo (deviation low holdback), Hi (deviation high holdback) or bAnd (deviation band
holdback)] for the entire program. The controller will default to “OFF.”
Hb.U: Press the UP or DOWN ARROW to
select the holdback value (in display units).
22
8 SEGMENT & 4X16 SEGMENT PROGRAMMABLE MODELS
W/OTP
rmP.U: Press the UP or DOWN ARROW to
toggle between ramp units (SEc, min or
Hour). Controller will default to “SEc.”
dwL.U: Press the UP or DOWN ARROW to
toggle between dwell units (SEc, min or
Hour). Controller will default to “SEc.”
Cyc.n: Press the UP or DOWN ARROW to
set the number of program cycles (1 to 999 or
cont). The controller will default to “cont.”
SEG.n: Press the UP or DOWN ARROW to
select the segment number (1-8 in 8 segment
models, 1-16 in 4x16 models).
tYPE: Press the UP or DOWN ARROW to
select the segment type [End (end of program), rmP.r = ramp rate (ramp to a specified
setpoint at a set rate), rmp.t = ramp time
(ramp to a specified temperature in a set
time), dwEll (to maintain a constant temperature for a set time), StEP (climb instantaneously from current to specified temperature), cALL (to call a program as a subroutine,
available only on 4x16 programmable models)]. The controller will default to “End.” Other
parameters used with tYPE include; tGt target
setpoint), Rate (rate of temperature increase)
and dur (time to target setpoint or time to
dwell).
End.t: End segment type: dwELL (dwell continuous), rSEt (reset) and S OP (End
Segment Output power level.
AL LiSt (Alarm List)
IdHi: Deviation High Alarm.
Atun LiSt: (Autotune List)
tunE: One-shot autotune enable.
23
8 SEGMENT & 4X16 SEGMENT PROGRAMMABLE MODELS
W/OTP
drA: Adaptive tune enable.
drA.t: Adaptive tune trigger level in display
units. Range = 1 9999.
Pid LiSt
G.SP (Gain Setpoint): Is the temperature at
which the controller switches from the (SEt1)
PID values to the (SEt 2) PID values.
Pb: Proportional band in display units. (SEt 1)
ti: Integral time in seconds. (SEt 1)
td: Derivative time in seconds. (SEt 1)
Pb2: Proportional band. (SEt 2)
ti2: Integral time in seconds. (SEt 2)
td2: Derivative time in seconds. (SEt 2)
Note
The following alarm messages are factory default settings and may vary if you
have changed the configuration of your
controller:
IDHi: =
50°C
2FSH = 1225°C
ACCS LiSt (Access List)
Access Code (Code needed to enter or
change the other configuration parameters
which are not normally accessible.) Not
accessable.
Alarms
The controller will flash an alarm message in
the home display if an alarm condition is
detected.
IdHi: PV deviation high alarm.
2FSH: PV full scale high alarm.
24
8 SEGMENT & 4X16 SEGMENT PROGRAMMABLE MODELS
W/OTP
LCr: load current low alarm.
HCr: load current high alarm.
S.br: Sensor break: check that sensor is connected correctly.
L.br: Loop Break: Check that the heating circuits are working properly.
Ld.F: Heater Circuit Fault: indication of either
an open or short solid sate relay, a blown
fuse, missing supply or open circuit heater.
SSr.F: Solid state relay failure indications in a
solid state relay: indicates either an open or
short circuit in the SSR.
Htr.F: Heater failure: Indication that there is a
fault in the heating circuit: indicates either a
blown fuse, missing supply or open circuit
heater.
Sensor Break Protection
This controller provides sensor break protection in the event the thermocouple opens. If
an open thermocouple condition occurs, the
digital display will Blink “S.br” and the power
to the heating element will be shut OFF
(Cycle light will extinguish).
Over-Temperature Protection
(OTP)
The OTP will be in effect during any alarm
condition when the temperature of the furnace
has deviated beyond the limit. The “Deviation
25
8 SEGMENT & 4X16 SEGMENT PROGRAMMABLE MODELS
W/OTP
High” alarm is the only alarm value which can
be changed. To change it, press the SCROLL
button until “idHi” appears on the display.
Press the UP or DOWN button to select the
OTP value you desire. We recommend a
value of 20° above your working temperature
to provide protection for your workload.
To Operate the Controller as a
Single Setpoint Controller
1.
Switch the circuit breaker to the “ON”
position. The setpoint temperature
presently set in the controller will
appear in the lower display. (The
upper display indicates the actual
chamber temperature.)
2.
To change the setpoint, press the UP
or DOWN button until the desired setpoint value is displayed; then release
the button.
3.
The furnace will begin to heat if the
new setpoint temperature is higher
than the present chamber temperature.
Programming the Controller
The controller is capable of varying temperature or process value with time through programming. A program is stored as a series of
segments and can be run once, repeated a
set number of times or run continuously. To
create a customized program using the controller parameters listed under “Controller
26
8 SEGMENT & 4X16 SEGMENT PROGRAMMABLE MODELS
W/OTP
Parameters” at the beginning of this section,
follow the procedures outlined in the proceeding sections of this manual.
Creating a New Program or Editing an
Existing Program (4x16 Segment
Programmable Models Only)
The same steps are used when creating a
new program and editing an existing program
with the exception being that a new program
starts with all its segments set to End in the
tYPE parameter. Temporary changes can be
made to these parameters when the program
is in the hold state but permanent changes
must be made in the reset state. Follow the
steps below to create or edit a program.
1. Press the PAGE button until you
reach the program list (ProG LiSt).
2.
Press the SCROLL button until display reads, “PrG.n.”
3.
Press the UP or DOWN button to
select a number for a new program or
to edit an existing program.
Hb: Holdback
Holdback consists of a value and a type. If
the measured value lags behind the setpoint
by an undesirable amount during a ramp or
dwell, the holdback feature can be used to
freeze the program at its current state (the
HOLD light will flash). The program will
resume when the error comes within the holdback value.
OFF: holdback is disabled.
27
8 SEGMENT & 4X16 SEGMENT PROGRAMMABLE MODELS
W/OTP
Lo (Deviation Low Holdback): holds the program back when process variable deviates below
the setpoint by more than the holdback value.
Hi (Deviation High Holdback): holds the program back when process variable deviates above
the setpoint by more than the holdback value.
bAnd (Deviation Band Holdback): combines
the features of the high and low deviation holdback in that it holds the program back when the
process variable deviates above or below the
setpoint by more than the holdback value.
Note
The value set in this parameter is always
for the entire program.
To set the holdback type:
1. Press the PAGE button until you reach
the program list (ProG LiSt).
2.
Press the SCROLL button until display
reads, “Hb.”
3.
Press the UP or DOWN button to toggle
between “bAnd, Hi, Lo and OFF.”
Hb U: Holdback Value
To set the holdback value:
1. Press the PAGE button until you reach
the program list (ProG LiSt).
2.
Press the SCROLL button until display
reads, “Hb.U.”
3.
Press the UP or DOWN button to enter a
holdback value.
rmP.U: Setting Ramp Units
Ramp units are time units which are used in
28
8 SEGMENT & 4X16 SEGMENT PROGRAMMABLE MODELS
W/OTP
“rmP.r” segments (ramp to a setpoint at
degrees per second, minute or hour) and
“rmP.t” segments (ramp to setpoint in a specific amount of time). See “Setting the
Segment Type” for an explanation on how to
set a ramp segment.
1. Press the PAGE button until you
reach the program list (ProG LiSt).
2.
Press the SCROLL button until display reads, “rmP.U.”
3.
Press the UP or DOWN button to toggle between seconds, minutes and
hours.
dwL.U: Setting Dwell Units
Dwell units are time units which are used in
“dwELL” segments (amount of time to remain
at a specific temperature ). See “Setting the
Segment Type” for an explanation on how to
set a dwell segment.
1. Press the PAGE button until you
reach the program list (ProG LiSt).
2.
Press the SCROLL button until display reads, “dwL.U.”
3.
Press the UP or DOWN button to toggle between seconds, minutes and
hours.
CYC.n: Setting the Number of Cycles
Set the number of times a group of segments
or programs are to be repeated by following
the steps listed below.
1. Press the PAGE button until you
reach the program list (ProG LiSt).
29
8 SEGMENT & 4X16 SEGMENT PROGRAMMABLE MODELS
W/OTP
2.
Press the SCROLL button until display
reads,”CYC.n.”
3.
Press the UP or DOWN button to select
the number of cycles you want to run or,
press the DOWN button to select “cont.”
so the program will run continuously.
Setting the Segment Type
Note
The program ramp rate is designed to
reduce the heatup rate or cooling rate
that the furnace normally exhibits. When
not using this feature, the furnace will
operate at its maximum heating and
cooling capability.
Note
When the program ramp has ended or
has been reset, the furnace will continue
to maintain setpoint temperature. It will
not cool to ambient temperature unless
the setpoint is set to ambient temperature by the program or by the operator.
30
There are five segment types. Proceed with the
following steps according to the type of segment
you have selected.
rmP.r (Ramp)
To ramp linearly at a set rate to a specified temperature:
1. Press the PAGE button until you reach
the program list (ProG LiSt).
2.
Press the SCROLL button until display
reads,”tYPE.”
3.
Press the UP or DOWN button until display reads, “rmP.r.”
Steps 4 and 5 are used in the 4 program model
only. If you are using an 8 segment program, skip
to step 6.
4.
Press the SCROLL button until display
reads “Hb.”
5.
Press the UP or DOWN button to toggle
between “bAnd, Hi, Lo and OFF.”
6.
Press the SCROLL button until display
reads, “tGt.”
7.
Press the UP or DOWN button to set a
target setpoint.
8.
Press the SCROLL button until display
8 SEGMENT & 4X16 SEGMENT PROGRAMMABLE MODELS
W/OTP
reads,”rAtE.”
9.
Press the UP or DOWN button to select
a value in ramp units (seconds, minutes
or hours; set in the “rmP.U” parameter).
rmP.t
To ramp to a specified temperature at a set
time:
1. Press the PAGE button until you reach
the program list (ProG LiSt).
2.
Press the SCROLL button until display
reads, “tYPE.”
3.
Press the UP or DOWN button until display reads, “rmP.t.”
4.
Press the SCROLL button until display
reads, “tGt.”
5.
Press the UP or DOWN button to set a
target setpoint.
6.
Press the SCROLL button until display
reads, “dur.”
7.
Press the UP or DOWN button to select
a time in ramp units (seconds, minutes
or hours; set in the “rmP.U” parameter.
dwEll
To maintain a constant temperature for a specified time:
1. Press the PAGE button until you reach
the program list (ProG LiSt).
2.
Press the SCROLL button until display
reads, “tYPE.”
3.
Press the UP or DOWN button until display reads, “dwEll.”
31
8 SEGMENT & 4X16 SEGMENT PROGRAMMABLE MODELS
W/OTP
4.
Press the SCROLL button until display reads, “dur.”
5.
Press the UP or DOWN button to
select a time in dwell units (seconds,
minutes or hours; set in the “dwL.U”
parameter).
StEP
To climb instantaneously from the current
temperature to a specified temperature.
1. Press the PAGE button until you
reach the program list (ProG LiSt).
2.
Press the SCROLL button until display reads, tYPE.”
3.
Press the UP or DOWN button until
the display reads, “StEP.”
4.
Press the SCROLL button until display reads, “tGt.”
5.
Press the UP or DOWN button to set
a target setpoint.
cALL (Running Multiple Programs; 4x16
Segment Programmable Models Only)
To call a program as a subroutine:
If you want to run multiple programs, you can
program the controller to “call” or link one program to another. This makes it possible to run
one program at any time during another program and also return to the original program if
desired.
1. Press the PAGE button until you
reach the program list (ProG LiSt).
2.
32
Press the SCROLL button until display reads, “tYPE.”
8 SEGMENT & 4X16 SEGMENT PROGRAMMABLE MODELS
W/OTP
3.
Press the UP or DOWN button until display reads, “cALL.”
4.
Press the SCROLL button until display
reads, “PrG.n.”
5.
Press the UP or DOWN button to select
a program number to be linked.
6.
Press the SCROLL button until display
reads, “CYC.n.”
7.
Press the UP or DOWN button to select
the number of cycles the linked program
is to be run.
End
To end or repeat a program:
1. Press the PAGE button until you reach
the program list (ProG LiSt).
2.
Press the SCROLL button until display
reads, “tYPE.”
3.
Press the UP or DOWN button until display reads, “End.”
4.
Press the SCROLL button until display
reads, “End.t.”
5.
Press the UP or DOWN button to toggle
between “dwEll” (an indefinite dwell), “S
OP” (End Segment Output Power) and
“rSET” (reset).
Setting the Target Setpoint (4x16
Segment Programmable Models Only)
1.
Press the PAGE button until you reach
the program list (ProG LiSt).
33
8 SEGMENT & 4X16 SEGMENT PROGRAMMABLE MODELS
W/OTP
2.
Press the SCROLL button until display
reads, “tGt.”
3.
Press the UP or DOWN button to set
the target setpoint temperature.
Running a Program (8
Segment Programmable
Models)
To run a program, press the RUN/HOLD button. (The RUN light will illuminate.)
Running a Program (4x16
Segment Programmable
Models)
To run a program, press the RUN/HOLD button. (The RUN light will illuminate) or:
1. Press the PAGE button until you
reach the run list (run LiSt).
34
2.
Press the SCROLL button until display
reads, “PrG.”
3.
Press the UP or DOWN button to
select the program number you want
to run.
4.
Press the RUN/HOLD button once to
start the program. (The RUN light will
illuminate.)
8 SEGMENT & 4X16 SEGMENT PROGRAMMABLE MODELS
W/OTP
Holding a Program
To put a running program on hold, press the
RUN/HOLD button. (The HOLD light will illuminate.)
Note
Display will flash “tu.ER” if an error
occurs during tuning. To clear the
error and restart tuning, simultaneously press the PAGE and SCROLL
buttons and follow the steps outlined
in “Autotuning.”
Note
To stop the tuning function, simultaneously press the PAGE and
SCROLL buttons.
Cancelling a Program
To cancel a program, hold the RUN/HOLD button down until the RUN and HOLD lights go off.
Tuning your Furnace
The purpose of tuning your furnace is to match
the characteristics of your controller to the characteristics of the process being controlled. Good
control is evidenced by: stable, straight-line control of the setpoint temperature with no fluctuations; No overshoot or undershoot of the setpoint temperature; rapid restoration of the setpoint temperature when external disturbances
cause deviations from the setpoint.
This controller has automatic tuning features
which install optimum tuning parameters to give
the best temperature accuracy. No manual loading of tuning parameters is needed. We recommend that you tune the furnace to your specific
application to obtain the best results. To provide
the best temperature accuracy possible, use
these features when you install your furnace
and whenever you change your application or
procedure.
Tuning Error
The display will flash “tu.ER” if an error occurs
during tuning. To clear the error and restart tuning, simultaneously press the PAGE and
SCROLL buttons and follow the steps outlined
in “Autotuning.”
35
8 SEGMENT & 4X16 SEGMENT PROGRAMMABLE MODELS
W/OTP
Gain Scheduling
G.SP: Gain Scheduling
Gain scheduling is the automatic transfer of
control between two sets of PID values. The
2416 controller does this at a presettable
process value. Gain scheduling is used for
difficult control processes which show large
changes in their response time or sensitivity
at high or low temperatures, or when heating
or cooling.
The G.SP gain schedule setpoint is factory
set at 700° C. The G.SP must be adjusted to
200°C from the desired setpoint temperature
when tuning.
Setting the Transfer Point
If gain scheduling has been enabled, “G.SP
will appear at the top of the PID list. This sets
the value at which the transfer will occur.
When the process value is below this level,
PID1 will be active and when it is above, Pid2
will be active. Set a value between the control
regions that show the greatest change to
achieve the best point of transfer.
Tuning
The two sets of PID values can be manually
set or automatically tuned. To tune automatically you must tune above and below the
transfer point G.SP. If the process value is
below the transfer point G.SP, the calculated
values will automatically be inserted into the
(SEt 1) set and if the process value is above
G.SP, the calculated values will automatically
be inserted into the (SEt 2).
36
8 SEGMENT & 4X16 SEGMENT PROGRAMMABLE MODELS
W/OTP
Autotuning
The Autotune feature automatically sets up the
PID values in the control parameters to suit new
process conditions.
To tune your furnace using autotuning:
1. Load your furnace with a load similar to
your normal load and close the door.
2.
Set the setpoint temperature.
3.
Press the PAGE button until the display
reads, “Atun LiSt.”
4.
Press the SCROLL button until “tunE
OFF” is displayed.
5.
Press the UP or DOWN button to select
“on.”
6.
Simultaneously press the PAGE and
SCROLL buttons to return to the HOME
DISPLAY. The display will flash “tunE”
while tuning is in progress.
Adaptive Tuning
Adaptive tuning continuously evaluates tuning
parameters. Adaptive tuning automatically
installs new values if better accuracy is possible. Adaptive tuning should be used when the
characteristics of a process change due to load
or setpoint changes or, in a process that can not
handle the oscillation caused by a one-shot
tune.
To tune your furnace using adaptive tuning:
1. Load your furnace with a load characteristic of those you intend to heat in it.
2. Press the PAGE button until display
37
8 SEGMENT & 4X16 SEGMENT PROGRAMMABLE MODELS
W/OTP
reads, “Atun LiSt.”
38
3.
Press the SCROLL button until “drA
OFF” is displayed.
4.
Press the UP or DOWN button to
select “on.”
5.
Press the SCROLL button until “drA.t”
is displayed.
6.
Press the UP or DOWN button until
the desired trigger value is achieved.
Furnace Loading
Caution
Do not overload your furnace chamber. If
the load is to be heated uniformly, it
should not occupy more than two-thirds
of the furnace chamber. Maintain at least
a 3/4” gap between the load and elements. Failure to observe this caution
could result in damage to the furnace
components.
•
For best results, use only the center
two-thirds of the furnace chamber.
•
If you are heating a number of small
parts, spread them throughout the
center two-thirds of the furnace chamber.
•
Keep objects away from the thermocouple.
•
Use insulated tongs and mittens when
loading and unloading the furnace.
•
Always wear safety glasses.
•
Never come into contact with the
heating elements. Hitting the elements with tongs or laying the load
against them will cause the elements
to burn out prematurely.
Thermocouple
Thermocouple Sample Port
Heating Elements
39
Preventive Maintenance
This unit is equipped with a venting system
on the top of the furnace. This is for the
removal of fumes from the chamber of the
unit.
Contamination is a major cause of element
failure, therefore, remove all fume forming
material before heating. (e.g. clean cutting
oil from tool steel).
Housekeeping is vital to your electric furnace
– KEEP IT CLEAN. Run your furnace up to
871°C (1600°F) empty occasionally to burn
off the contamination that may exist on the
insulation and elements. Maintain 871°C
(1600°F) for at least 4 hours to ensure complete ashing of foreign materials.
Element life is reduced somewhat by repeated heating and cooling. If the furnace is to
be used again within a few hours, it is best
to keep it at the operating temperature or at
a reduced level such as 260°C (500°F). We
highly recommend that you replace the thermocouple periodically (once every six
months) to ensure temperature accuracy.
General Cleaning Instructions
Wipe exterior surfaces with a lightly dampened cloth containing a mild soap solution.
40
Troubleshooting
The Troubleshooting section is intended to aid in defining and correcting possible service
problems. When using the chart, select the problem category that resembles the malfunction. Then proceed to the possible causes category and take necessary corrective action.
Problem
Cycle light does not
illuminate.
Furnace does not heat.
Possible Causes
The furnace is not
connected to power supply.
Corrective Action
Reconnect furnace to power
supply.
Incorrect power source.
Connect to correct power
source.
ON and OFF power switch
defective.
Replace power switch.
Defective cycle light.
Replace cycle light.
Door switch malfunction.
Realign or replace furnace
door safety switch.
No power.
Check power source and
fuses or breakers.
Defective electrical hookup.
Repair electrical hookup.
Thermocouple has oxidized and Replace thermocouple.
opened the circuit.
Controller malfunction.
Replace controller.
Heating elements
burned out.
Replace defective elements.
Door switch malfunction.
Realign or replace door safety
switch.
Defective OTP relay.
Replace relay.
Defective solid state relay.
Replace relay.
41
TROUBLESHOOTING
Door switch does
not cut power to
heating elements.
Door switch not functioning.
Controller over-temp.
does not cut power
to furnace chamber.
Alarm output device malfunction. Replace controller.
Slow heatup.
Repeated element
burnout.
42
Realign or replace door safety
switch.
OTP relay malfunction.
Replace relay.
Element shorted to ground.
Replace faulty element.
Low line voltage.
Install line of sufficient size
and voltage (isolate furnace
from other electrical loads).
Heavy load in chamber.
Lighten load in chamber to
allow heat to circulate.
Wrong heating element.
Install proper element.
Heating element burned
out.
Replace element.
Overheating furnace.
Keep furnace under maximum
temperature. Closer supervision of control setting.
Heating harmful materials.
Enclose material in container.
Clean up spills in and on
chamber. Ventilate chamber by
leaving top vent slightly open
when heating known harmful
reagents.
Contamination from previous
burnout.
Replace insulation material.
TROUBLESHOOTING
Inaccurate temp.
readout.
Oxidized or contaminated
thermocouple.
Replace thermocouple.
Poor thermocouple connection.
Tighten connections.
Improper loading procedures.
Use proper loading
procedures.
Poor ventilation of control.
Clear area around furnace
control.
Thermocouple connections
reversed.
Reconnect thermocouple
correctly.
43
Maintenance and Servicing
Warning
To avoid electrical shock, this furnace
must always be disconnected from the
power supply prior to maintenance and
service.
Perform only maintenance described in
this manual. Contact an authorized dealer or our factory for parts and assistance.
To Replace a Heating Element
1.
Disconnect the furnace from the
power supply.
2.
Remove the back terminal cover of
the furnace. (Note placement and
connection of wires.)
3.
Loosen the nuts on the terminal points
of the four heating element lead wires
and remove the element wires from
the terminals.
4.
Loosen the thermocouple hold-down
clip and carefully remove the thermocouple from the rear of the furnace
chamber.
5.
Remove both the back of the furnace
and the blanket insulation.
6.
Grasp the element lead wires and pull
out both elements and the back
chamber insulation.
7.
Replace the defective element.
8.
Reverse the disassembly procedure,
making sure you thread all element
lead wires through the insulating
porcelain bushings on the back of the
furnace and cut off any excess element lead wire after securing the
leads to the terminal points.
9.
Reconnect the furnace to the power
supply.
Refer servicing to qualified
personnel.
Note
The ceramic hearth collar may crack.
This is a normal condition and will not
affect the performance of the hearth collar.
10. Test the operation of the furnace.
44
MAINTENANCE AND SERVICING
To Replace a Chromel/Alumel
Thermocouple (All Furnaces)
1.
Disconnect the furnace from the
power supply.
2.
Remove both back covers. (Note
placement and connection of wires.)
3.
Remove the clip holding the thermocouple in place (1 screw), and
remove the two screws on the thermocouple terminals.
4.
Remove the thermocouple. (Note:
first pull the thermocouple straight
out of the hole in the chamber to
avoid damage to the insulation.)
5.
Guide the looped ends of the new
thermocouple through the plastic
bushings with the red (-) lead to the
right as you face the back of the furnace.
6.
Insert the thermocouple straight
through the hole in the chamber.
7.
Secure the thermocouple with clip
and screw. Connect the looped ends
of the thermocouple to the terminals
with “+” to “+” (yellow) and “-” to “-”
(red) wires. A polarity test of the thermocouple and lead wire is easily
made with the use of a magnet. On
a Chromel/Alumel thermocouple and
lead wire, the non-magnetic wire is
positive (+) and the magnetic wire is
negative (-).
45
MAINTENANCE AND SERVICING
8.
Replace both back covers.
9.
Reconnect to the power supply.
10. Test the operation of the furnace.
To Replace Door Switches
(Micro-Switch)
46
1.
Disconnect the furnace from the
power supply.
2.
Remove the screws on the front dial
and the screws and lock washers on
the back cover.
3.
Slide the control section forward.
(Note: do not pull excessively on the
internal wires.)
4.
Disconnect the wires from the door
switch. (Note the connection placement of the wires to the microswitch.)
5.
Remove the screws and nuts from
the micro-switch.
6.
Insert new micro-switches and
secure with the screws and nuts
removed in step 5.
7.
Reconnect the wires to the new door
switch.
8.
To realign the door switches, see the
following section, “To Realign Door
Switches.”
9.
Slide the control section back and
replace the screws and lock washers
MAINTENANCE AND SERVICING
described in step 2.
10. Reconnect to the power supply.
11. Test the operation of the door switches. (See next section, step 8.)
To Realign Door Switches
(Micro-Switch):
1.
Disconnect the furnace from the
power supply.
2.
Remove the lower rear cover.
3.
With the door closed, loosen the
screws on the micro-switch bracket
and gently push the switch bracket
forward until you hear a click.
4.
Open and close the door; the switch
should click when the door is opened
approximately 3" and 1" to 2” before
the door is closed. Slide the switches
backward to increase the distance,
forward to decrease the distance.
5.
Tighten the two screws to secure the
switches. Check the operation of the
switch as described in step 4 after
tightening the screws.
6.
Replace the back cover.
7.
Reconnect to power supply.
8.
To test the operation of the door
switch: move the power switch on, set
the control to a setting high enough to
keep the control from cycling, open
47
MAINTENANCE AND SERVICING
and close the door; the cycle light
should turn OFF when the door is
opened approximately 3" and turn
back ON 1” to 2” before the door is
closed.
To Replace the Controller
The controller plugs into a panel mounting
sleeve which should be left permanently
installed in the furnace housing. To remove
the controller, release the side clips and slide
the controller out. Do not attempt to dismantle
this unit further; replace it with a Thermolyne
loaner or a new unit.
48
Replacement Parts
Warning
Replace fuses with same type and rating.
Single Setpoint Models
F47910, F47910-26, F47910-33, F47914, F47915, F48010, F48010-26, F48010-33, F48014, F48015,
F48015-60, F48018
Part number
CN71X96
CN71X73
CAX94
EL479X1A
EL479X2A
EL480X1A
EL480X2A
EL1205X1
FZX30
PLX76
PLX82
RYX34
SWX163
SWX143
SWX144
TRX136
TC1165X1
Description
Controller
Controller
Line Filter
Element
Element
Element
Element
Element
Line Fuse
Pilot Light
Pilot Light
S.S. Relay
Door Switch
Power Switch
Power Switch
Terminal Block
Thermocouple
QTY.
1
1
1
2
2
2
2
2
2
1
1
1
2
1
1
1
1
Notes
F48010-33 only
.
All Models except F48010-33
“-33” models only.
120 & 240 volt F47900 models only.
100 volt F47900 models only.
120 & 240 volt F48000 models only, except “-33” models.
100 & 208 volt F48000 models only.
“-33” F48000 models only.
“-33” models only.
100 &120 volt models only.
208 & 240 volt models only.
All Models
All Models
100 &120 volt models only
208 & 240 volt models only.
All Models
All Models
Single Setpoint Models with OTP
F47920, F47920-26, F47920-33, F47924, F47925, F48020, F48020-26, F48020-33, F48024, F48025,
F48025-60, F48028
Part number
CN71X100
CN71X99
CAX94
EL479X1A
EL479X2A
EL480X1A
EL480X2A
EL1205 X1
FZX30
PLX76
PLX82
RYX34
RYX56
RYX57
SWX163
SWX143
SWX144
TRX136
TC1165X1
Description
Controller
Controller
Line Filter
Element
Element
Element
Element
Element
Line Fuse
Pilot Light
Pilot Light
S.S. Relay
Mechanical Relay
Mechanical Relay
Door Switch
Power Switch
Power Switch
Terminal Block
Thermocouple
QTY.
1
1
1
2
2
2
2
2
2
1
1
1
1
1
2
1
1
1
1
Notes
F48020-33 only
.
All Models except F48020-33
“-33 models only.
120 & 240 volt F47900 models only.
100 volt F47900 models only.
120 & 240 volt F48000 models only, except “-33” models.
100 & 208 volt F48000 models only.
“-33” F48000 models only.
“-33” models only.
100 &120 volt models only.
208 & 240 volt models only.
All Models
100 & 120 volt models only.
208 & 240 volt models only.
All Models
100 &120 volt models only
208 & 240 volt models only.
All Models
All Models
49
REPLACEMENT
PARTS
8 Segment Programmable Models with OTP
F47920-80, F47920-26-80, F47920-33-80, F47924-80, F47925-80, F48020-80, F48020-26-80, F48020-33-80,
F48024-80, F48025-80, F48025-60-80, F48028-80
Part number
CN71X97
CN71X74
CAX94
EL479X1A
EL479X2A
EL480X1A
EL480X2A
EL1205X1
FZX30
PLX76
PLX82
RYX34
RYX56
RYX57
SWX163
SWX143
SWX144
TRX136
TC1165X1
Description
Controller
Controller
Line Filter
Element
Element
Element
Element
Element
Line Fuse
Pilot Light
Pilot Light
S.S. Relay
Mechanical Relay
Mechanical Relay
Door Switch
Power Switch
Power Switch
Terminal Block
Thermocouple
QTY.
1
1
1
2
2
2
2
2
2
1
1
1
1
1
2
1
1
1
1
Notes
-33 models only
.
All models except -33 models
“-33” models only.
120 & 240 volt F47900 models only.
100 volt F47900 models only.
120 & 240 volt F48000 models only, except “-33” models.
100 & 208 volt F48000 models only.
“-33” F48000 models only.
“-33” models only.
100 &120 volt models only.
208 & 240 volt models only.
All Models
100 & 120 volt models only.
208 & 240 volt models only.
All Models
100 &120 volt models only
208 & 240 volt models only.
All Models
All Models
4 X 16 Segment Programmable Models with OTP
F47950, F47950-26, F47950-33, F47954, F47955, F48050, F48050-26, F48050-33, F48055, F48055-60,
F48058
Part number
CN71X98
CN71X75
CAX94
EL479X1A
EL479X2A
EL480X1A
EL480X2A
EL1205X1
FZX30
PLX76
PLX82
RYX34
RYX56
RYX57
SWX163
SWX143
SWX144
TRX136
TC1165X1
50
Description
Controller
Controller
Line Filter
Element
Element
Element
Element
Element
Line Fuse
Pilot Light
Pilot Light
S.S. Relay
Mechanical Relay
Mechanical Relay
Door Switch
Power Switch
Power Switch
Terminal Block
Thermocouple
QTY.
1
1
1
2
2
2
2
2
2
1
1
1
1
1
2
1
1
1
1
Notes
-33 models only
.
All models except -33 models
“-33 models only.
120 & 240 volt F47900 models only.
100 volt F47900 models only.
120 & 240 volt F48000 models only, except “-33” models.
100 & 208 volt F48000 models only.
“-33” F48000 models only.
“-33” models only.
100 &120 volt models only.
208 & 240 volt models only.
All Models
100 & 120 volt models only.
208 & 240 volt models only.
All Models
100 &120 volt models only
208 & 240 volt models only.
All Models
All Models
DESCRIPTION
CONTROL
PILOT LIGHT
FUSE
FUSE
FILTER
HEATING ELEMENT
HEATING ELEMENT
RELAY, SOLID STATE
SWITCH, POWER
SWITCH, DOOR
SWITCH, DOOR
TERMINAL BLOCK
THERMOCOUPLE
REF.
NO.
CN1
DS1
F1
F2
FL1
H1
H2
RY1
S1
S2
S3
TB1
TC1
DIAGRAM COMPONENT LIST
T1
H1
T2
T1
H1
240V
H2
100/120V
H2
EL479X1A
EL479X1A
RYX34
SWX144
SWX163
SWX163
TRX136
TC1165X1
EL479X1A
EL479X1A
RYX34
SWX144
SWX163
SWX163
TRX136
TC1165X1
T2
CN71X73
PLX104
CN71X73
PLX104
T4
T3
T4
T3
CN71X73
PLX104
FZX30
FZX30
CAX98
EL480X1A
EL480X1A
RYX34
SWX144
SWX163
SWX163
TRX136
TC1165X1
MODEL NO. AND OUR PART NO.(s)
F47910-26
F47910-33
F47910
F47914
GND
L2
L1
EL479X2A
EL479X2A
RYX34
SWX143
SWX163
SWX163
TRX136
TC1165X1
CN71X73
PLX103
EL479X1A
EL479X1A
RYX34
SWX143
SWX163
SWX163
TRX136
TC1165X1
FL1
F47910-33
ONLY
L2
GND
L1
F47915
CN71X73
PLX103
F1
F2
S1
S2
S3
-4
1
1B
1A
CN1
RY1
-
+
3+
2
V-
V+
AB
AA
N
L
DS1
TB1
RED
YELLOW
TC1
Wiring Diagrams
SINGLE SETPOINT CONTROL
51
52
-
+
DASHED LINES "
"
DENOTE 100/120 V.
WIRE CONNECTIONS.
V-
V+
AB
AA
N
L
TC1
TC+
YEL
TB1
TCRED
-
WIRING DIAGRAM
2
3
1
4
L1
+
T1
H1
T2
S3
S2
RY2
RY1
L2
S1
T4
H2
T3
DS1
CONTROL
PILOT LIGHT, NEON
FUSE
FUSE
FILTER, EMI
HEATING ELEMENT
HEATING ELEMENT
RELAY, DPST, N.O.
SOLID STATE RELAY
SWITCH
DOOR SWITCH
DOOR SWITCH
TERMINAL BLOCK
THERMOCOUPLE
CN1
DS1
F1
F2
FL1
H1
H2
RY1
RY2
S1
S2
S3
TB1
TC1
F2
F1
FL1
L2
G
L1
F47920-33
ONLY
GND
GND
L2
G
LINE
LINE
EL479X1A
EL479X1A
RYX57
RYX34
SWX144
SWX163
SWX163
TRX136
TC1165X1
EL479X1A
EL479X1A
RYX57
RYX34
SWX144
SWX163
SWX163
TRX136
TC1165X1
L1
F47920-26
CN71X99
PLX82
F47920
CN71X99
PLX82
LOAD
NOTES:
1B
1A
CN1
DESCRIPTION
REF.
NO.
F47924
CN71X99
PLX76
EL479X2A
EL479X2A
RYX56
RYX34
SWX143
SWX163
SWX163
TRX136
TC1165X1
F47920-33
CN71X99
PLX82
FZX30
FZX30
CAX94
EL479X1A
EL479X1A
RYX57
RYX34
SWX144
SWX163
SWX163
TRX136
TC1165X1
DIAGRAM COMPONENT LIST
MODEL NO. AND OUR PART NO.(s)
EL479X1A
EL479X1A
RYX56
RYX34
SWX143
SWX163
SWX163
TRX136
TC1165X1
F47925
CN71X99
PLX76
WIRING DIAGRAMS
SINGLE SETPOINT CONTROL W/OTP
LINE
HF
3B
NOTES:
DASHED LINES "
"
DENOTE 100/120 V.
WIRE CONNECTIONS.
TC1
TCRED
V-
V+
VI
N
L
-
1
4
+
2
3
T1
T2
S3
S2
H1
RY2
RY1
S1
T4
H2
T3
CN1
DS1
F1
F2
FL1
H1
H2
RY1
RY2
S1
S2
S3
TB1
TC1
REF.
NO.
DS1
CONTROL
PILOT LIGHT, NEON
FUSE
FUSE
FILTER, EMI
HEATING ELEMENT
HEATING ELEMENT
RELAY, DPST, N.O.
SOLID STATE RELAY
SWITCH
DOOR SWITCH
DOOR SWITCH
TERMINAL BLOCK
THERMOCOUPLE
DESCRIPTION
F2
F1
FL1
L2
G
L1
F47920-33-80
ONLY
GND
GND
LINE
LINE
EL479X1A
EL479X1A
RYX57
RYX34
SWX144
SWX163
SWX163
TRX136
TC1165X1
EL479X1A
EL479X1A
RYX57
RYX34
SWX144
SWX163
SWX163
TRX136
TC1165X1
L1
CN71X74
PLX82
CN71X74
PLX82
L2
G
F47920-26-80
F47920-80
CN71X74
PLX82
FZX30
FZX30
CAX94
EL479X1A
EL479X1A
RYX57
RYX34
SWX144
SWX163
SWX163
TRX136
TC1165X1
F47920-33-80
DIAGRAM COMPONENT LIST
MODEL NO. AND OUR PART NO.(s)
LOAD
TC+
YLW
TB1
HE
3A
GND
HC
2A
HD
HB
1B
2B
HA
1A
WIRING DIAGRAM
EL479X1A
EL479X1A
RYX56
RYX34
SWX143
SWX163
SWX163
TRX136
TC1165X1
EL479X2A
EL479X2A
RYX56
RYX34
SWX143
SWX163
SWX163
TRX136
TC1165X1
F47925-80
CN71X74
PLX76
CN71X74
PLX76
F47924-80
8 SEGMENT
WIRING DIAGRAMS
PROGRAMMABLE CONTROL
LINE
53
54
HD
HE
HF
2B
3A
3B
RED
YLW
+
2
3
T1
T2
S3
S2
H1
RY2
T4
H2
T3
DS1
F2
F1
GND
GND
CN71X75
PLX82
EL479X1A
EL479X1A
RYX57
RYX34
SWX144
SWX163
SWX163
TRX136
TC1165X1
CN71X75
PLX82
EL479X1A
EL479X1A
RYX57
RYX34
SWX144
SWX163
SWX163
TRX136
TC1165X1
L2
G
L1
L2
G
LINE
LINE
F47950-26
F47950
F47954
EL479X2A
EL479X2A
RYX56
RYX34
SWX143
SWX163
SWX163
TRX136
TC1165X1
CN71X75
PLX76
TD 2
SG 7
RD 3
O
B
W
CONNECTOR
F47955
EL479X1A
EL479X1A
RYX56
RYX34
SWX143
SWX163
SWX163
TRX136
TC1165X1
CN71X75
PLX76
HE
HF
HD
CONTROLLER
COMMUNICATION CABLE WIRING
EL479X1A
EL479X1A
RYX57
RYX34
SWX144
SWX163
SWX163
TRX136
TC1165X1
CN71X75
PLX82
FZX30
FZX30
CAX94
F47950-33
DIAGRAM COMPONENT LIST
MODEL NO. AND OUR PART NO.(s)
L1
F47950-33 ONLY
FL1
CONTROL
PILOT LIGHT, NEON
FUSE
FUSE
FILTER, EMI
HEATING ELEMENT
HEATING ELEMENT
RELAY, DPST, N.O.
SOLID STATE RELAY
SWITCH
DOOR SWITCH
DOOR SWITCH
TERMINAL BLOCK
THERMALCOUPLE
DESCRIPTION
LINE
NOTES:
DASHED LINES "
"
DENOTE 100/120 V.
WIRE CONNECTIONS.
-
1
4
RY1
S1
CN1
DS1
F1
F2
FL1
H1
H2
RY1
RY2
S1
S2
S3
TB1
TC1
REF.
NO.
LOAD
TC1
TC-
V-
V+
TC+
TB1
HC
2A
GND
N
HB
1B
VI
L
HA
1A
WIRING DIAGRAMS
4 X 16 SEGMENT PROGRAMMABLE CONTROL
DESCRIPTION
CONTROL
PILOT LIGHT
FUSE
FUSE
FILTER
HEATING ELEMENT
HEATING ELEMENT
RELAY, SOLID STATE
SWITCH, POWER
SWITCH, DOOR
SWITCH, DOOR
TERMINAL BLOCK
THERMOCOUPLE
REF.
NO.
CN1
DS1
F1
F2
FL1
H1
H2
RY1
S1
S2
S3
TB1
TC1
DIAGRAM COMPONENT LIST
T1
H1
T2
T1
H1
240V
H2
100/120V
H2
EL480X1A
EL480X1A
RYX34
SWX144
SWX163
SWX163
TRX136
TC1165X1
EL480X1A
EL480X1A
RYX34
SWX144
SWX163
SWX163
TRX136
TC1165X1
T2
CN71X73
PLX82
F48010-26
CN71X73
PLX82
F48010
T4
T3
T4
T3
CN71X96
PLX82
FZX30
FZX30
CAX98
EL1205X1
EL1205X1
RYX34
SWX144
SWX163
SWX163
TRX136
TC1165X1
F48010-33
MODEL NO. AND OUR PART NO.(s)
F48014
GND
L2
L1
EL480X2A
EL480X2A
RYX34
SWX143
SWX163
SWX163
TRX136
TC1165X1
CN71X73
PLX76
FL1
F1
F2
F48010-33 ONLY
L2
GND
L1
EL480X1A
EL480X1A
RYX34
SWX143
SWX163
SWX163
TRX136
TC1165X1
CN71X73
PLX76
F48015, F48015-60
TC1165X1
EL480X2A
EL480X2A
RYX34
SWX144
SWX163
SWX163
TRX136
CN71X73
PLX82
F48018
S1
S2
S3
-4
1
1B
1A
CN1
RY1
-
+
3+
2
V-
V+
AB
AA
N
L
DS1
TB1
RED
YELLOW
TC1
SINGLE
WIRING DIAGRAMS
SETPOINT CONTROL
55
56
-
+
DASHED LINES "
"
DENOTE 100/120 V.
WIRE CONNECTIONS.
V-
V+
AB
AA
N
L
TC1
TC+
YEL
TB1
TCRED
-
2
3
1
4
L1
+
T1
H1
T2
S3
S2
RY2
RY1
L2
S1
T4
H2
T3
DS1
CYCLE
CONTROL
PILOT LIGHT, NEON
FUSE
FUSE
FILTER, EMI
HEATING ELEMENT
HEATING ELEMENT
RELAY, DPST, N.O.
SOLID STATE RELAY
SWITCH
DOOR SWITCH
DOOR SWITCH
TERMINAL BLOCK
THERMOCOUPLE
CN1
DS1
F1
F2
FL1
H1
H2
RY1
RY2
S1
S2
S3
TB1
TC1
DIAGRAM COMPONENT LIST
F2
F1
EL480X1A
EL480X1A
RYX57
RYX34
SWX144
SWX163
SWX163
TRX136
TC1165X1
F48020
CN71X99
PLX82
FL1
L2
G
L1
F48020-33
ONLY
GND
GND
L2
G
LINE
LINE
EL1205X1
EL1205X1
RYX57
RYX34
SWX144
SWX163
SWX163
TRX136
TC1165X1
EL480X1A
EL480X1A
RYX57
RYX34
SWX144
SWX163
SWX163
TRX136
TC1165X1
L1
F48020-33
CN71X100
PLX82
FZX30
FZX30
CAX94
F48020-26
CN71X99
PLX82
MODEL NO. AND OUR PART NO.(s)
LOAD
NOTES:
1B
1A
CN1
WIRING DIAGRAM
DESCRIPTION
REF.
NO.
EL480X2A
EL480X2A
RYX56
RYX34
SWX143
SWX163
SWX163
TRX136
TC1165X1
F48024
CN71X99
PLX76
EL480X1A
EL480X1A
RYX56
RYX34
SWX143
SWX163
SWX163
TRX136
TC1165X1
F48025, F48025-60
CN71X99
PLX76
EL480X2A
EL480X2A
RYX57
RYX34
SWX144
SWX163
SWX163
TRX136
TC1165X1
F48028
CN71X99
PLX82
WIRING DIAGRAMS
SINGLE SETPOINT CONTROL W/OTP
LINE
HF
3B
RED
YLW
NOTES:
DASHED LINES "
"
DENOTE 100/120 V.
WIRE CONNECTIONS.
TC1
TC-
V-
V+
VI
N
L
-
1
4
+
2
3
T1
T2
S3
S2
H1
RY2
RY1
S1
T4
H2
T3
CN1
DS1
F1
F2
FL1
H1
H2
RY1
RY2
S1
S2
S3
TB1
TC1
REF.
NO.
DS1
CONTROL
PILOT LIGHT, NEON
FUSE
FUSE
FILTER, EMI
HEATING ELEMENT
HEATING ELEMENT
RELAY, DPST, N.O.
SOLID STATE RELAY
SWITCH
DOOR SWITCH
DOOR SWITCH
TERMINAL BLOCK
THERMOCOUPLE
DESCRIPTION
F2
F1
FL1
L2
G
L1
L2
G
F47950-33
ONLY
GND
GND
EL480X1A
EL480X1A
RYX57
RYX34
SWX144
SWX163
SWX163
TRX136
TC1165X1
EL480X1A
EL480X1A
RYX57
RYX34
SWX144
SWX163
SWX163
TRX136
TC1165X1
LINE
LINE
CN71X97
PLX82
FZX30
FZX30
CAX94
EL1205X1
EL1205X1
RYX57
RYX34
SWX144
SWX163
SWX163
TRX136
TC1165X1
CN71X74
PLX82
L1
F48020-33-80
F48020-26-80
CN71X74
PLX82
F48020-80
EL480X2A
EL480X2A
RYX56
RYX34
SWX143
SWX163
SWX163
TRX136
TC1165X1
CN71X74
PLX76
F48024-80
DIAGRAM COMPONENT LIST
MODEL NO. AND OUR PART NO.(s)
LOAD
TC+
TB1
HE
3A
GND
HC
2A
HD
HB
1B
2B
HA
1A
WIRING DIAGRAM
EL480X1A
EL480X1A
RYX56
RYX34
SWX143
SWX163
SWX163
TRX136
TC1165X1
EL480X2A
EL480X2A
RYX57
RYX34
SWX144
SWX163
SWX163
TRX136
TC1165X1
CN71X74
PLX82
F48025-80, F48025-60-80 F48028-80
CN71X74
PLX76
8 SEGMENT
WIRING DIAGRAMS
PROGRAMMABLE CONTROL
LINE
57
58
HD
HE
HF
2B
3A
3B
-
1
4
+
2
3
T1
T2
S3
S2
H1
RY2
RY1
S1
T4
H2
T3
CN1
DS1
F1
F2
FL1
H1
H2
RY1
RY2
S1
S2
S3
DS1
TB1
TC1
F2
F1
FL1
GND
GND
EL480X1A
EL480X1A
RYX57
RYX34
SWX144
SWX163
SWX163
TRX136
TC1165X1
EL480X1A
EL480X1A
RYX57
RYX34
SWX144
SWX163
SWX163
TRX136
TC1165X1
L2
G
L1
L2
G
LINE
LINE
CN71X75
PLX82
CN71X75
PLX82
L1
F48050-26
CN71X98
PLX82
FZX30
FZX30
CAX94
EL1205X1
EL1205X1
RYX57
RYX34
SWX144
SWX163
SWX163
TRX136
TC1165XA
F48050-33
EL480X1A
EL480X1A
RYX56
RYX34
SWX143
SWX163
SWX163
TRX136
TC1165X1
CN71X75
PLX76
TD 2
SG 7
RD 3
O
B
W
CONNECTOR
HE
HF
HD
CONTROLLER
EL480X2A
EL480X2A
RYX57
RYX34
SWX144
SWX163
SWX163
TRX136
TC1165X1
CN71X75
PLX82
F48055, F48055-60 F48058
COMMUNICATION CABLE WIRING
MODEL NO. AND OUR PART NO.(s)
DIAGRAM COMPONENT LIST
F48050
F48050-33 ONLY
CONTROL
PILOT LIGHT, NEON
FUSE
FUSE
FILTER, EMI
HEATING ELEMENT
HEATING ELEMENT
RELAY, DPST, N.O.
SOLID STATE RELAY
SWITCH
DOOR SWITCH
DOOR SWITCH
TERMINAL BLOCK
THERMALCOUPLE
DESCRIPTION
LINE
NOTES:
DASHED LINES "
"
DENOTE 100/120 V.
WIRE CONNECTIONS.
RED
TC-
V-
V+
REF.
NO.
LOAD
TC1
TC+
YLW
TB1
HC
2A
GND
N
HB
1B
VI
L
HA
1A
WIRING DIAGRAMS
4 X 16 SEGMENT PROGRAMMABLE
CONTROL
Ordering Procedures
Please refer to the Specification Plate for the complete model number, serial number, and series number
when requesting service, replacement parts or in any correspondence concerning this unit.
All parts listed herein may be ordered from the Barnstead International dealer from whom you purchased
this unit or can be obtained promptly from the factory. When service or replacement parts are needed we ask
that you check first with your dealer. If the dealer cannot handle your request, then contact our Customer
Service Department at 563-556-2241 or 800-553-0039.
Prior to returning any materials to Barnstead International, please contact our Customer Service Department
for a “Return Goods Authorization” number (RGA). Material Returned without an RGA number will be returned.
59
One Year Limited Warranty
BARNSTEAD INTERNATIONAL (“BARNSTEAD”) warrants that if a product manufactured by Barnstead shall
be free of defects in materials and workmanship for one (1) year from the first to occur of (i) the date the product is sold by BARNSTEAD or (ii) the date the product is purchased by the original retail customer (the
“Commencement Date”). Except as expressly stated above, BARNSTEAD MAKES NO OTHER WARRANTY,
EXPRESSED OR IMPLIED, WITH RESPECT TO THE PRODUCTS AND EXPRESSLY DISCLAIMS ANY AND
ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO, WARRANTIES OF DESIGN, MERCHANT ABILITY
AND FITNESS FOR A PARTICULAR PURPOSE.
An authorized representative of BARNSTEAD must perform all warranty inspections. In the event of a defect
covered by BARNSTEAD’s warranty, BARNSTEAD shall, as its sole obligation and exclusive remedy, provide
free replacement parts to remedy the defective product. In addition, for products sold by BARNSTEAD within
the continental United States or Canada, BARNSTEAD shall provide provide free labor to repair the products
with the replacement parts, but only for a period of ninety (90) days from the Commencement Date.
BARNSTEAD’s warranty provided hereunder shall be null and void and without further force or effect if there
is any (i) repair made to the product by a party other than BARNSTEAD or its duly authorized service representative, (ii) misuse (including use inconsistent with written operating instructions for the product), mishandling, contamination, overheating, modification or alteration of the product by any customer or third party or
(iii) use of replacement parts that are obtained from a party who is not an authorized dealer of BARNSTEAD.
Heating elements, because of their susceptibility to overheating and contamination, must be returned to the
BARNSTEAD factory and if, upon inspection, it is concluded that failure is due to factors other than excessive
high temperature or contamination, BARNSTEAD will provide warranty replacement. As a condition to the
return of any product, or any constituent part thereof, to BARNSTEAD’s factory, it shall be sent prepaid and a
prior written authorization from BARNSTEAD assigning a Return Goods Number to the product or part shall
be obtained.
IN NO EVENT SHALL BARNSTEAD BE LIABLE TO ANY PARTY FOR ANY DIRECT, INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES, OR FOR ANY DAMAGES RESULTING FROM LOSS OF
USE OR PROFITS, ANTICIPATED OR OTHERWISE, ARISING OUT OF OR IN CONNECTION WITH THE
SALE, USE OR PERFORMANCE OF ANY PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, TORT (INCLUDING NEGLIGENCE), ANY THEORY OF STRICT LIABILITY OR REGULATORY
ACTION.
The name of the authorized Barnstead International dealer nearest you may be obtained by calling 1-800-4466060 (563-556-2241) or writing to:
2555 Kerper Boulevard
P.O. Box 797
Dubuque, Iowa 52001-0797
Phone: 563-556-2241 or 800-553-0039
Fax: 563-589-0516
E-mail: mkt@barnstead.com
www.barnstead.com
60
Download PDF