ATCOM | AT-620 | Atcom AT620P Server Setup Guide

Atcom AT620P with Elastix Server
Setup Guide
http://www.elastix.org
PaloSanto Solutions
Atcom AT620P Server Setup Guide
1.0 Setup Diagram
Figure 1-1 is a setup diagram for a single IP Phone AT620P configuration. The phone is
setup as a SIP telephony device.
Figure 1-1. Setup Diagram
2.0 Host PC Environment
Hardware Type
Hardware Version
Software Type
Software Version
Table 2-1. Host Server Environment Details
Description
Elastix Appliance ELX-Series
ELX-3000
Elastix
2.3
3.0 Test Setup Equipment
Equipment
IP (SIP) Phone
Atcom
Switch
Table 3-1. Test Setup Equipment
Model
Version
N/A
N/A
AT620P
1.7.370.151
N/A
N/A
2
PaloSanto Solutions
Atcom AT620P Server Setup Guide
4.0 Setup Procedure
To set up the Elastix Server for the Atcom AT620P,
1. Go to the web address of the Elastix Server Login page. The web address is
determined by the customer, for this guide we have used the IP address 192.168.1.65
2. On the Login page, type the username and password for an administrative user into
the Username and Password fields, see Figure 4-1. The username and password are
determined by the customer.
Figure 4-1. Login
3. Press Enter or click on the Submit button to go to Elastix’s Dashboard
4. Once inside, click on the PBX tab on the menu at the top of the screen
Figure 4-2. Dashboard
5. Click on the Submit button to add an extension, see Figure 4-3. This will take you to
the Add SIP Extension page.
3
PaloSanto Solutions
Atcom AT620P Server Setup Guide
Figure 4-3. Add an Extension
6. On the Add SIP Extension page (Figure 4-4), fill in the following information:
• User Extension (301 in this example)
• Display Name (‘AtcomAT620’ in this example)
• secret (‘h7Dka3Rf9si0t’ in this example)
Figure 4-4. Add SIP Extension
7. Click on the ‘Submit’ button at the end of the page. The extension will be created and
you will see the page on Figure 4-5 displaying the “Apply Configuration Changes Here”
pink ribbon on top of the screen.
8. Click in the “Apply Configuration Changes Here” link
4
PaloSanto Solutions
Atcom AT620P Server Setup Guide
Figure 4-5. Apply Configuration Changes Here
9. With this you have just finished creating a SIP extension that will be used by the
Atcom AT620P to register with the Elastix Server. Repeat Steps 5 through 8 to similarly
create another extension (different values on Step 6) to be used by the IP (SIP) Phone to
register as well (extension 302 in this example). Once finished you will see something
similar to Figure 4-6
Figure 4-6. Atcom and IP Phone extensions successfully created
10. You will need to enter the information from the extension created on the Elastix
Server into the Atcom Phone.
For the initial configuration, refer to the Atcom AT620P User Manual which can be
found at: http://www.atcom.cn/AT620P.html
Factory default settings
IP Addressing
DHCP
Web Access User Name admin
Web Access Password
admin
11. Log in to the Atcom AT620P WebUI by pointing your browser to the Atcom
Phone’s IP address.
12. When prompted, enter the Web Access Username and Web Access Password to
access the Atcom WebUI (Figure 4-7).
5
PaloSanto Solutions
Atcom AT620P Server Setup Guide
Figure 4-7. Atcom AT620P WebUI
To register the Atcom Phone we have two methods: Manual Configuration and
AutoProvisioning using Elastix’s Endpoint Configurator.
6
PaloSanto Solutions
Atcom AT620P Server Setup Guide
MANUAL CONFIGURATION
1. Use the information from the Add SIP Extension page (Figure 4-4) to enter the
following necessary information on “VOIP => SIP 1” section of the Atcom Phone
WebUI:






Server Address: Elastix Server’s IP Address (192.168.1.65 in this example)
Account Name: 301 in this example
Password: ‘h7Dka3Rf9si0t’ in this example
Phone number: 301 in this example
Enable Register: Checked
Display Name: “AtcomUser” in this example
Figure 4-8. Account Configuration
2. Once you have entered the required information, click on ‘Apply’ button located at
the end of the page. To check if the phone is registered, refresh the current page and see
the “Register Status” label. If the phone is not register make sure you have entered the
right information (Figure 4.9).
Figure 4.9. VOIP
3. Configure the other IP (SIP) Phone with the correct parameters.
7
PaloSanto Solutions
Atcom AT620P Server Setup Guide
4. To test the Atcom AT620P, pick up the previously configured IP (SIP) Phone and
call the AT620P’s extension number (301 in this example). When the call is established,
speak into the phone and verify that the other IP (SIP) Phone can hear your voice.
Check this by calling from both ends. This step completes the manual procedure.
8
PaloSanto Solutions
Atcom AT620P Server Setup Guide
AUTOPROVISIONING USING ELASTIX’S ENDPOINT
CONFIGURATOR
1. In the Elastix WebUI go to “PBX => Endpoint Configurator” (Figure 4-10).
Figure 4.10 Endpoint Configurator
2. Next to the “Discover Endpoints in this Network” button, type the address where
the phone is located and click the button. This will generate a list with all the
phones available in that network (Figure 4-11).
Figure 4.11 Endpoint Configurator
3. In the row where the phone you want to autoprovision is located (find it according
to either its MAC or IP Address):



Mark the checkbox
From the drop-down list, select the correct “Phone Type” (phone model) of the
phone
From the drop-down list, select the “User Extension” you want to assign to the
phone
9
PaloSanto Solutions
Atcom AT620P Server Setup Guide
Figure 4.12 Endpoint Configurator
4. Click the “Set” button. This will reboot the phone. After the phone has finished
rebooting, it will be automatically configured with the selected User Extension.
5. Configure the other IP (SIP) Phone with the correct parameters.
6. To test the Atcom AT620P, pick up the previously configured IP (SIP) Phone and
call the AT620P’s extension number (301 in this example). When the call is
established, speak into the phone and verify that the other IP (SIP) Phone can hear
your voice. Check this by calling from both ends.
10
Download PDF

advertising