Sharp | AL-1225 | Copier - OlsonBros

Use this information as a guide for CCD-MCU harness compatibility. Replacing the MCU is NOT recommended
as additional MCU programming may be required.
Copier
Technical Bulletin
Sharp Electronics Corporation
Services and Support Group
1300 Naperville Drive
Romeoville, IL 60446
Number: AR-153E-007
Date: June 2003
ALL MCU AND ELECTRICAL PART SALES ARE FINAL NO RETURNS FOR ANY REASON.
Subject: Parts Change To The MCU PWB (L1-00 Trouble).
1. Model:
AL-1215/1530CS/1540CS/1551CS
AR-153E/157E/153EN/157EN
2. Symptom:
The Copy Lamp is intermittently turned off which may cause L1-00
trouble.
3. Corrective Action:
If L1-00 trouble is experienced, replace the resistor R239 to the
new style (5.6k ohm type).
4. Note:
Check the condition of transistor Q108 (PN: VSKTA1281++-1)
when troubleshooting the MCU PWB after replacing R239.
Refer to page 2 for part descriptions and price ranks.
DCE-370
Bulletin #: AR-157E-007
Page 1 of 2
From January 2003 production.
Model
AL-1215
AL-1530CS
AL-1540CS
AL-1551CS
AR-153E
AR-157E
AL-1215
AL-1530CS
AL-1540CS
AL-1551CS
AR-153E
AR-157E
AR-153EN
AR-157EN
P/G
No.
Previous Part
New Part
Price
Rank
Description
Interchangeability
VRS-CZ1JD471J
VRS-CZ1JD562J
AA
Resistor R239
3
30-901
CPWBX0112QS31
CPWBX0112QS32
CPWBX0112QS33
CPWBX0112QS34
MCU PWB
1
28-901
CPWBX0112QS3D
CPWBX0121QS41
CPWBX0121QS42
CPWBX0121QS43
CPWBX0121QS44
CPWBX0121QS3C
CPWBX0121QS3D
30-901
CPWBX0121QS33
CPWBX0121QS34
30-109
28-109
No Change
Interchangeability
1. Interchangeable
4.
2. Current type can be used in place of new type.
5.
New type cannot be used in place of current type.
3. Current type cannot be used in place of the new type.
6.
New type can be used in place of current type.
BW
BX
BY
Not interchangeable
Interchangeable if replaced with
same types of related parts in use.
Others.
Note 1: When replacing the MCU PWB on the AR-153E/157E/153EN/157EN make sure to
look at the Serial Number Plate on the rear of the machine to determine if you have an “E”
model or “EN” model. The MCU PWB’s are different for these models. On the “E” version
Connector CN106 is 4 pins and on the “EN” version CN106 is 10 pins.
Note 2: On machines produced from January 2003 production resistor R239 has been changed
to the 5.6k ohm type so the new MCU PWB’s will have the new style resistor.
DCE-370
Bulletin #: AR-157E-007
Page 2 of 2
Copier
Technical Bulletin
Number: AR-153E-004
Sharp Electronics Corporation
Services and Support Group
1300 Naperville Drive
Romeoville, IL 60446
Date: April 2003
Subject: MCU PWB Clarification.
1. Model:
AR-153E/157E/153EN/157EN
AL-1551CS
2. General:
The following correction has been made to the Parts Guide for the
models listed above.
From 1 st Lot production.
Model
AR-153E
AR-157E
AR-153EN
AR-157EN
P/G
No.
Previous Part
New Part
Price
Rank
28-901
CPWBX0112QS3D
CPWBX0112QS34
BX
CPWBX0121QS33
No Change
CPWBX0121QS34
Interchangeability
1. Interchangeable
4.
2. Current type can be used in place of new type.
5.
New type cannot be used in place of current type.
3. Current type cannot be used in place of the new type.
6.
New type can be used in place of current type.
30-901
Description
Note
Interchangeability
MCU PWB
6
BY
Not interchangeable
Interchangeable if replaced with
same types of related parts in use.
Others.
Note: CPWBX0112QS34 is no longer available as a service item from our National
Parts Center. When ordering a MCU PWB from our National Parts Center please use
the Part Numbers provided below.
From January 2003 production.
Model
AR-153E
AR-157E
AL-1551CS
P/G
No.
Previous Part
New Part
Price
Rank
Description
Note
Interchangeability
CPWBX0121QS3C
CPWBX0121QS3D
BX
MCU PWB
30-901
CPWBX0121QS44
Interchangeability
1. Interchangeable
4. Not interchangeable
2. Current type can be used in place of new type.
5. Interchangeable if replaced with
New type cannot be used in place of current type.
same types of related parts in use.
3. Current type cannot be used in place of the new type.
6. Others.
New type can be used in place of current type.
28-901
DCE-342
CPWBX0112QS34
Bulletin #: AR-153E-004
1
Page 1 of 1
MFP
Service Bulletin
Sharp Document Solutions Company of America
Service & Support Group
Number:MFP-SB-020
Date: February 2005
Models:
AL-1215/1216/1217/1225/1226/1530CS/1540CS/1551CS/1555/1631/1641CS
AL-1645CS/1651CS/1661CS
AR153E/153EN/157E/157EN/168D/168S
Subject:
Notes When Replacing The CCD-MCU Harness (Section 10, Item 40)
To improve productivity, the CCD-MCU Harness is changed from the folded type to the straight
type. CCD-MCU Harness replacement procedure is shown in this document.
From July, 2004 production.
P/G
No.
Previous Part
New Part
Price
Rank
Description
Interchangeability
10-40
DHAI-0268QSZZ
DHAI-0268QSZ1
DHAI-0268QSZ3
AG
CCD MCU HARNESS
1
Interchangeability
1. Interchangeable
4. Not interchangeable
2. Current type can be used in place of new type.
5. Interchangeable if replaced with
New type cannot be used in place of current type.
same types of related parts in use.
3. Current type cannot be used in place of the new type.
6. Others.
New type can be used in place of current type.
CCD-MCU Harness Replacement Procedure
1. Remove the table glass and attach the CCD-MCU harness to the carriage unit. Leave 10mm
between the optical base plate and carriage unit.
DCE-512
MFP-SB-020
Page 1 of 5
2. Adjust the space between the end face of the optical base plate and harness to 5mm.
3. Lay the CCD-MCU harness along the dotted line as illistrated on the optical base plate.
Ensure that the CCD-MCU harness has no slack.
DCE-512
MFP-SB-020
Page 2 of 5
4.
Apply double-sided tape (PTPE-0045QSZZ/19 x 10mm) along the reference line shown
in the figure below.
5. Fix the CCD-MCU harness with double-sided tape and fold it along the reference line (a
dotted line) shown in the figure below.
6. Fold the CCD-MCU harness and apply filament tape (40 x 19mm) along the dotted line of
to secure the harness.
DCE-512
MFP-SB-020
Page 3 of 5
7. Straighten the CCD-MCU harness so there is no slack. Slide the carriage unit and
harness to the right and left three times. *Refer to the figures below for where to slide.
8. Leave 10mm between the optical base plate and carriage unit as mentioned in the step 1
and ensure that the CCD-MCU harness is straightened. If the CCD-MCU harness is inclined,
adjust its position until it is straightened.
9. Mount the cable-retaining sheet (PSHEZ0367QSZ1) along the notch.
DCE-512
MFP-SB-020
Page 4 of 5
10. Fold the CCD-MCU harness as shown in the figure below in order to prevent it from being
jammed.
[1] Fold the CCD-MCU harness with it inserted into the connector.
[2] Fold it approx. 10mm away from the connector jack.
DCE-512
MFP-SB-020
Page 5 of 5
MFP
Parts Bulletin
Sharp Document Solutions Company of America
Service & Support Group
Number: MFP-PB-045
Date: January 2005
Model(s): AL-1530CS/1540CS/1551CS/1631/1641CS
AR-153E/153EN/157E/157EN
Subject: Parts Change to the Carriage Unit.
Description: The parts for the carriage unit are changed to ones commonly used with new
products.
From August 2004 production.
Previous Part
New Part
DUNT-0276QS11
PMLT-0068QSZZ
PSHEZ0401QSZ1
LFIX-0025QSZZ
PSHEZ0390QSZZ
Price
Rank
Description
DUNT-0404QSZZ
BU
None
---
Carriage Unit
Core Holder
Scanner Core Sheet
CCD Harness Holder
PWB Holder Sheet
Interchangeability
1. Interchangeable
4.
2. Current type can be used in place of new type.
5.
New type cannot be used in place of current type.
3. Current type cannot be used in place of the new type.
6.
New type can be used in place of current type.
DCE-522R
Interchangeability
5
Not interchangeable
Interchangeable if replaced with
same types of related parts in use.
Others.
Parts Bulletin #: MFP-PB-045
Page 1 of 1
Download PDF