Ultra Start 450 SERIES Setup guide

Setup Guide
CrossPoint 450 Plus Series
CrossPoint Ultra Series
MAV Plus Series
Matrix Switchers
Extron USA - West
Headquarters
+800.633.9876
Inside USA / Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron USA - East
Extron Europe
Extron Asia
Extron Japan
Extron China
Extron Middle East
+800.633.9876
+800.3987.6673
+800.7339.8766
+81.3.3511.7655
+81.3.3511.7656 FAX
+400.883.1568
+971.4.2991800
+971.4.2991880 FAX
+1.919.863.1794
+1.919.863.1797 FAX
+31.33.453.4040
+31.33.453.4050 FAX
+65.6383.4400
+65.6383.4664 FAX
Inside USA / Canada Only
Inside Europe Only
Inside Asia Only
© 2009 Extron Electronics. All rights reserved.
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
68-521-50 Rev. B
07 09
Precautions
Safety Instructions • English
This symbol is intended to alert the user of important
operating and maintenance (servicing) instructions in
the literature provided with the equipment.
This symbol is intended to alert the user of the
presence of uninsulated dangerous voltage within
the product’s enclosure that may present a risk of
electric shock.
Caution
Read Instructions • Read and understand all safety and operating
instructions before using the equipment.
Retain Instructions • The safety instructions should be kept for future
reference.
Follow Warnings • Follow all warnings and instructions marked on the
equipment or in the user information.
Avoid Attachments • Do not use tools or attachments that are not
recommended by the equipment manufacturer because they may be
hazardous.
Consignes de Sécurité • Français
Ce symbole sert à avertir l’utilisateur que la
documentation fournie avec le matériel contient des
instructions importantes concernant l’exploitation et
la maintenance (réparation).
Ce symbole sert à avertir l’utilisateur de la présence
dans le boîtier de l’appareil de  tensions dangereuses
non isolées posant des risques d’électrocution.
Attention
Lire les instructions• Prendre connaissance de toutes les consignes de
sécurité et d’exploitation avant d’utiliser le matériel.
Conserver les instructions• Ranger les consignes de sécurité afin de pouvoir
les consulter à l’avenir.
Respecter les avertissements • Observer tous les avertissements et consignes
marqués sur le matériel ou présentés dans la documentation utilisateur.
Eviter les pièces de fixation • Ne pas utiliser de pièces de fixation ni d’outils
non recommandés par le fabricant du matériel car cela risquerait de poser
certains dangers.
Sicherheitsanleitungen • Deutsch
Dieses Symbol soll dem Benutzer in der im
Lieferumfang enthaltenen Dokumentation
besonders wichtige Hinweise zur Bedienung und
Wartung (Instandhaltung) geben.
Dieses Symbol soll den Benutzer darauf aufmerksam
machen, daß im Inneren des Gehäuses dieses
Produktes gefährliche Spannungen, die nicht isoliert
sind und die einen elektrischen Schock verursachen
können, herrschen.
Achtung
Lesen der Anleitungen • Bevor Sie das Gerät zum ersten Mal verwenden,
sollten Sie alle Sicherheits-und Bedienungsanleitungen genau durchlesen
und verstehen.
Aufbewahren der Anleitungen • Die Hinweise zur elektrischen Sicherheit
des Produktes sollten Sie aufbewahren, damit Sie im Bedarfsfall darauf
zurückgreifen können.
Befolgen der Warnhinweise • Befolgen Sie alle Warnhinweise und
Anleitungen auf dem Gerät oder in der Benutzerdokumentation.
Keine Zusatzgeräte • Verwenden Sie keine Werkzeuge oder Zusatzgeräte,
die nicht ausdrücklich vom Hersteller empfohlen wurden, da diese eine
Gefahrenquelle darstellen können.
Instrucciones de seguridad • Español
Este símbolo se utiliza para advertir al usuario
sobre instrucciones importantes de operación y
mantenimiento (o cambio de partes) que se desean
destacar en el contenido de la documentación
suministrada con los equipos.
Este símbolo se utiliza para advertir al usuario sobre
la presencia de elementos con voltaje peligroso sin
protección aislante, que puedan encontrarse dentro
de la caja o alojamiento del producto, y que puedan
representar riesgo de electrocución.
Precaucion
Leer las instrucciones • Leer y analizar todas las instrucciones de operación y
seguridad, antes de usar el equipo.
Conservar las instrucciones • Conservar las instrucciones de seguridad para
futura consulta.
Obedecer las advertencias • Todas las advertencias e instrucciones marcadas
en el equipo o en la documentación del usuario, deben ser obedecidas.
Evitar el uso de accesorios • No usar herramientas o accesorios que no
sean especificamente recomendados por el fabricante, ya que podrian
implicar riesgos.
Warning
Power sources • This equipment should be operated only from the power source
indicated on the product. This equipment is intended to be used with a main power
system with a grounded (neutral) conductor. The third (grounding) pin is a safety
feature, do not attempt to bypass or disable it.
Power disconnection • To remove power from the equipment safely, remove all power
cords from the rear of the equipment, or the desktop power module (if detachable),
or from the power source receptacle (wall plug).
Power cord protection • Power cords should be routed so that they are not likely to be
stepped on or pinched by items placed upon or against them.
Servicing • Refer all servicing to qualified service personnel. There are no userserviceable parts inside. To prevent the risk of shock, do not attempt to service
this equipment yourself because opening or removing covers may expose you to
dangerous voltage or other hazards.
Slots and openings • If the equipment has slots or holes in the enclosure, these are
provided to prevent overheating of sensitive components inside. These openings
must never be blocked by other objects.
Lithium battery • There is a danger of explosion if battery is incorrectly
replaced. Replace it only with the same or equivalent type recommended by
the manufacturer. Dispose of used batteries according to the manufacturer’s
instructions.
Avertissement
Alimentations• Ne faire fonctionner ce matériel qu’avec la source d’alimentation
indiquée sur l’appareil. Ce matériel doit être utilisé avec une alimentation principale
comportant un fil de terre (neutre). Le troisième contact (de mise à la terre) constitue
un dispositif de sécurité : n’essayez pas de la contourner ni de la désactiver.
Déconnexion de l’alimentation• Pour mettre le matériel hors tension sans danger,
déconnectez tous les cordons d’alimentation de l’arrière de l’appareil ou du module
d’alimentation de bureau (s’il est amovible) ou encore de la prise secteur.
Protection du cordon d’alimentation • Acheminer les cordons d’alimentation de
manière à ce que personne ne risque de marcher dessus et à ce qu’ils ne soient pas
écrasés ou pincés par des objets.
Réparation-maintenance • Faire exécuter toutes les interventions de réparationmaintenance par un technicien qualifié. Aucun des éléments internes ne peut être
réparé par l’utilisateur. Afin d’éviter tout danger d’électrocution, l’utilisateur ne doit
pas essayer de procéder lui-même à ces opérations car l’ouverture ou le retrait des
couvercles risquent de l’exposer à de hautes tensions et autres dangers.
Fentes et orifices • Si le boîtier de l’appareil comporte des fentes ou des orifices, ceux-ci
servent à empêcher les composants internes sensibles de surchauffer. Ces ouvertures
ne doivent jamais être bloquées par des objets.
Lithium Batterie • Il a danger d’explosion s’ll y a remplacment incorrect de la batterie.
Remplacer uniquement avec une batterie du meme type ou d’un ype equivalent
recommande par le constructeur. Mettre au reut les batteries usagees conformement
aux instructions du fabricant.
Vorsicht
Stromquellen • Dieses Gerät sollte nur über die auf dem Produkt angegebene
Stromquelle betrieben werden. Dieses Gerät wurde für eine Verwendung mit einer
Hauptstromleitung mit einem geerdeten (neutralen) Leiter konzipiert. Der dritte
Kontakt ist für einen Erdanschluß, und stellt eine Sicherheitsfunktion dar. Diese
sollte nicht umgangen oder außer Betrieb gesetzt werden.
Stromunterbrechung • Um das Gerät auf sichere Weise vom Netz zu trennen, sollten
Sie alle Netzkabel aus der Rückseite des Gerätes, aus der externen Stomversorgung
(falls dies möglich ist) oder aus der Wandsteckdose ziehen.
Schutz des Netzkabels • Netzkabel sollten stets so verlegt werden, daß sie nicht im
Weg liegen und niemand darauf treten kann oder Objekte darauf- oder unmittelbar
dagegengestellt werden können.
Wartung • Alle Wartungsmaßnahmen sollten nur von qualifiziertem Servicepersonal
durchgeführt werden. Die internen Komponenten des Gerätes sind wartungsfrei.
Zur Vermeidung eines elektrischen Schocks versuchen Sie in keinem Fall, dieses
Gerät selbst öffnen, da beim Entfernen der Abdeckungen die Gefahr eines
elektrischen Schlags und/oder andere Gefahren bestehen.
Schlitze und Öffnungen • Wenn das Gerät Schlitze oder Löcher im Gehäuse aufweist,
dienen diese zur Vermeidung einer Überhitzung der empfindlichen Teile im
Inneren. Diese Öffnungen dürfen niemals von anderen Objekten blockiert werden.
Litium-Batterie • Explosionsgefahr, falls die Batterie nicht richtig ersetzt
wird. Ersetzen Sie verbrauchte Batterien nur durch den gleichen oder einen
vergleichbaren Batterietyp, der auch vom Hersteller empfohlen wird. Entsorgen Sie
verbrauchte Batterien bitte gemäß den Herstelleranweisungen.
Advertencia
Alimentación eléctrica • Este equipo debe conectarse únicamente a la fuente/tipo
de alimentación eléctrica indicada en el mismo. La alimentación eléctrica de este
equipo debe provenir de un sistema de distribución general con conductor neutro
a tierra. La tercera pata (puesta a tierra) es una medida de seguridad, no puentearia
ni eliminaria.
Desconexión de alimentación eléctrica • Para desconectar con seguridad la acometida
de alimentación eléctrica al equipo, desenchufar todos los cables de alimentación
en el panel trasero del equipo, o desenchufar el módulo de alimentación (si fuera
independiente), o desenchufar el cable del receptáculo de la pared.
Protección del cables de alimentación • Los cables de alimentación eléctrica se deben
instalar en lugares donde no sean pisados ni apretados por objetos que se puedan
apoyar sobre ellos.
Reparaciones/mantenimiento • Solicitar siempre los servicios técnicos de personal
calificado. En el interior no hay partes a las que el usuario deba acceder. Para evitar
riesgo de electrocución, no intentar personalmente la reparación/mantenimiento
de este equipo, ya que al abrir o extraer las tapas puede quedar expuesto a voltajes
peligrosos u otros riesgos.
Ranuras y aberturas • Si el equipo posee ranuras o orificios en su caja/alojamiento,
es para evitar el sobrecalientamiento de componentes internos sensibles. Estas
aberturas nunca se deben obstruir con otros objetos.
Batería de litio • Existe riesgo de explosión si esta batería se coloca en la posición
incorrecta. Cambiar esta batería únicamente con el mismo tipo (o su equivalente)
recomendado por el fabricante. Desachar las baterías usadas siguiendo las
instrucciones del fabricante.
Extron Warranty
Extron Electronics warrants this product against defects in materials and workmanship
for a period of three years from the date of purchase. In the event of malfunction during
the warranty period attributable directly to faulty workmanship and/or materials,
Extron Electronics will, at its option, repair or replace said products or components,
to whatever extent it shall deem necessary to restore said product to proper operating
condition, provided that it is returned within the warranty period, with proof of
purchase and description of malfunction to:
USA, Canada, South America,
and Central America:
Extron USA
1001 East Ball Road
Anaheim, CA 92805
U.S.A.
Europe, Africa, and the Middle East:
Extron Europe
Hanzeboulevard 10
3825 PH Amersfoort
The Netherlands
Asia:
Extron Asia
135 Joo Seng Road #04-01
PM Industrial Bldg.
Singapore 368363
Singapore
Japan:
Extron Japan
Kyodo Building, 16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
China:
Extron China
686 Ronghua Road, Songjiang
District
Shanghai 201611
China
Middle East:
Extron Middle East
Dubai Airport Free Zone
F12, PO Box 293666
United Arab Emirates, Dubai
This Limited Warranty does not apply if the fault has been caused by misuse, improper
handling care, electrical or mechanical abuse, abnormal operating conditions or nonExtron authorized modification to the product.
If it has been determined that the product is defective, please call Extron and ask for an
Applications Engineer at (714) 491-1500 (USA), 31.33.453.4040 (Europe), 65.6383.4400
(Asia), or 81.3.3511.7655 (Japan) to receive an RA# (Return Authorization number). This
will begin the repair process as quickly as possible.
Units must be returned insured, with shipping charges prepaid. If not insured, you
assume the risk of loss or damage during shipment. Returned units must include the
serial number and a description of the problem, as well as the name of the person to
contact in case there are any questions.
Extron Electronics makes no further warranties either expressed or implied with respect
to the product and its quality, performance, merchantability, or fitness for any particular
use. In no event will Extron Electronics be liable for direct, indirect, or consequential
damages resulting from any defect in this product even if Extron Electronics has been
advised of such damage.
Please note that laws vary from state to state and country to country, and that some
provisions of this warranty may not apply to you.
安全须知 • 中文
警告
这个符号提示用户该设备用户手册中
有重要的操作和维护说明。
电源 • 该 设 备 只 能 使 用 产 品 上 标 明 的 电 源 。 设 备
必须使用有地线的供电系统供电。 第三条线
(地线)是安全设施,不能不用或跳过。
这个符号警告用户该设备机壳内有暴
拔掉电源 • 为安全地从设备拔掉电源,请拔掉所有设备后
或桌面电源的电源线,或任何接到市电系统的电源线。
露的危险电压,有触电危险。
电源线保护 • 妥善布线, 避免被踩踏,或重物挤压。
注意
阅读说明书 • 用 户 使 用 该 设 备 前 必 须 阅 读 并 理
解所有安全和使用说明。
保存说明书 • 用户应保存安全说明书以备将来使
用。
遵守警告 • 用户应遵守产品和用户指南上的所有安
全和操作说明。
维护 • 所有维修必须由认证的维修人员进行。 设备内部
没有用户可以更换的零件。为避免出现触电危险不要自
己试图打开设备盖子维修该设备。
通风孔 • 有些设备机壳上有通风槽或孔,它们是用来防止
机内敏感元件过热。 不要用任何东西挡住通风孔。
锂电池 • 不正确的更换电池会有爆炸的危险。 必须使用
与厂家推荐的相同或相近型号的电池。 按照生产厂的
建议处理废弃电池。
避免追加 • 不要使用该产品厂商没有推荐的工具或
追加设备,以避免危险。
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. The Class A limits are designed to
provide reasonable protection against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference, in which case the user will be required to correct the interference at his
own expense.
N
This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used
with the unit to ensure compliance with FCC emissions limits.
Table of Contents
Chapter One • Introduction..................................................... 1-1
About this Manual..................................................................... 1-2
About the Matrix Switchers................................................... 1-2
Chapter Two • Installation....................................................... 2-1
Rear Panel..................................................................................... 2-2
Making connections and rear panel settings........................ 2-4
Front Panel Configuration Port
(Matrix Sizes up to 1616,
MAV Plus 32 A, and MAV Plus 248 A).................................. 2-7
Chapter Three • Front Panel Operation.......................... 3-1
Creating a Tie............................................................................... 3-2
Saving or Recalling a Preset. .................................................. 3-3
Setting the Front Panel Locks (Executive Modes)........... 3-4
Selecting Lock mode 2 or toggling between mode 2 and
mode 0..................................................................................... 3-4
Selecting Lock mode 2 or toggling between mode 2 and
mode 1..................................................................................... 3-5
Viewing and Adjusting the Audio Level. ........................... 3-5
Viewing Ties (and Muting Outputs).................................... 3-6
Chapter Four • Remote Control............................................ 4-1
Selected SIS Commands........................................................... 4-2
Establishing a network (Ethernet) connection..................... 4-2
Connection timeouts...............................................................4-2
Number of connections...........................................................4-3
Verbose mode..........................................................................4-3
Host-to-switcher instructions.................................................4-3
Installing and Starting the Control Program..................... 4-9
Installing the program............................................................ 4-9
Starting the program............................................................ 4-10
Accessing the HTML Pages.................................................... 4-12
Loading the start-up page.................................................... 4-12
All trademarks mentioned in this manual are the properties of their respective owners.
68-521-50 Rev. B
07 09
CrossPoint / MAV Matrix Switchers • Table of Contents
Refer also to the CrossPoint 450 Plus / CrossPoint Ultra / MAV Plus User’s Manual at www.extron.com.
i
Table of Contents, cont’d
CrossPoint / MAV Matrix Switchers
1
Chapter One
Introduction
About this Manual
About the Matrix Switchers
ii
CrossPoint / MAV Matrix Switchers • Table of Contents
Refer also to the CrossPoint 450 Plus / CrossPoint Ultra / MAV Plus User’s Manual at www.extron.com.
Introduction
N For more information on any subject in this guide, refer
to the CrossPoint 450 Plus / CrossPoint Ultra /
MAV Plus User’s Manual, available on the Extron disk
or at www.extron.com.
N In this manual, the term “CrossPoint”, when “450 Plus”
N In this manual, the term “video model” refers to any
CrossPoint or MAV Plus switcher that switches video.
In this manual, the term “audio model” refers to any
CrossPoint or MAV Plus switcher that switches audio.
or “Ultra” is not specified refers to either the
CrossPoint 450 Plus or the CrossPoint Ultra.
About this Manual
This setup guide allows you to easily and quickly set up and
configure your matrix switcher. Step by step instructions show
you how to connect the hardware. The guide also shows you
how to perform basic operations and use both the front panel
controls and selected Simple Instruction Set (SIS™) commands.
This guide also shows you how to load and start up the
Windows®-based Matrix Switchers Control Program. Lastly, this
guide shows you how to connect to the built-in HTML pages,
which you can use to operate the switcher.
Computer
4
1-2
•
HDA — HDTV/component video and audio
•
HD — HDTV/component video only
•
SVA — S-video and audio
•
SV — S-video only
•
AV — Composite video and audio
•
AV RCA — Composite video and audio on RCA connectors
(128 size only)
•
V — Composite video only
•
A — Audio only
CrossPoint / MAV Matrix Switchers • Introduction
Refer also to the CrossPoint 450 Plus / CrossPoint Ultra / MAV Plus User’s Manual at www.extron.com.
IN
IN
P
TP
2
23
17
30
28
22
L
31
L
L
L
L
1
2
18
100-240V ~ 50/60Hz 4.0A MAX
L
17
20
R
L
5
6
28
L
9
25
L
26
R
OU
TP
UT
R
9
L
25
L
27
L
11
L
10
L
26
L
27
L
13
L
29
L
28
L
12
R
L
13
L
29
L
15
L
31
L
15
R
L
31
R
R
L
14
L
30
L
32
L
16
L
32
R
RES
R
R
R
R
R
R
R
R
28
14
30
R
R
L
L
L
R
R
R
R
R
S
12
R
R
R
L
7
R
R
ET
Control
System
R
R
8
R
R
R
R
R
R
L
22
29
816
11
R
R
L
L
21
8
24
32
31
30
L
L
R
R
R
R
L
20
23
28
27
26
R
L
L
4
R
L
7
L
22
R
R
L
3
19
21
23
22
31
L
TS
R
L
L
19
R
L
18
6
R
L
L
2
R
L
5
R
R
R
L
1
4
R
L
L
17
L
L
3
R
R
L
L
, CA
HEIM
ANA
L
L
32
26
30
L
29
27
21
29
Ethernet
24
18
21
27
PU
20
19
25
30
IN
16
15
17
15
22
10
29
32
8
12
11
14
11
L
L
31
25
4
7
13
23
29
32
30
28
26
24
S
U T3
2
6
10
19
25
28
31
27
21
19
18
25
15
TP
5
14
27
26
22
20
14
OU
1
19
22
25
23
17
15
9
13
78
9
18
17
18
21
24
56
10
9
13
17
20
19
18
34
7
14
13
15
14
V
12
8
5
8
12
9
12
11
10
9
13
16
31
TS
PU
NC
IN
SY
H V
H
S 4
U T3
TP
OU 2
6
4
10
8
5
8
12
11
78
11
5
3
6
4
7
10
56
7
6
4
34
1
S
U T3
1
TS
1
S
U T3
2
6
5
TP
OU 2
N
PU
12
E
BLU
TS
EE
T
OU
D
RE
OU
1
PU
GR
S
UT
S
LINK ACT
29
32
31
30
UT
C
N
SY
ETHERNET
28
27
26
About the Matrix Switchers
31
25
30
22
21
29
P
IN
TS
RS 232/422
24
23
25
30
29
32
PU
IN
30
29
31
25
28
27
26
29
32
25
32
26
24
23
22
21
19
28
27
21
19
18
17
20
23
22
20
14
13
16
15
14
17
15
9
12
11
10
18
16
10
8
7
6
5
18
The MAV Plus matrix switchers are available in the following
models:
5
3
2
1
9
LAN
30
28
27
26
24
31
25
23
21
19
32
26
22
20
14
13
27
21
24
17
15
9
12
11
28
22
20
19
18
16
10
8
7
6
24
23
17
15
14
13
20
19
18
REMOTE
3
2
1
4
10
12
11
16
15
14
13
16
9
7
6
5
12
11
9
12
11
5
8
2
1
4
17
The CrossPoint switchers are available in HV (RGBHV video)
and HVA (RGBHV video and audio) models.
7
6
10
8
7
6
13
The Extron matrix switchers covered in this manual distribute
any input to any combination of outputs. The switchers can
route multiple input/output combinations simultaneously. The
switchers are available in a variety of matrix sizes (the number
of inputs and outputs).
8
2
1
4
3
2
1
4
3
23
24
R
R
R
R
R
R
R
R
Extron
Crosspoint 450 Plus 3232 HVA
DLP Projector
Ultra-Wideband Matrix Switcher
Figure 1-1 — Typical matrix switcher application
CrossPoint / MAV Matrix Switchers • Introduction
Refer also to the CrossPoint 450 Plus / CrossPoint Ultra / MAV Plus User’s Manual at www.extron.com.
1-3
Introduction, cont’d
CrossPoint / MAV Matrix Switchers
2
Chapter Two
Installation
Rear Panel
Front Panel Configuration Port (Matrix Sizes up to 1616)
1-4
CrossPoint / MAV Matrix Switchers • Introduction
Refer also to the CrossPoint 450 Plus / CrossPoint Ultra / MAV Plus User’s Manual at www.extron.com.
Installation
Rear Panel
N The MAV Plus switchers are housed in enclosures that
range from 8U (figure 2-2) to 2U to support their different
video format and matrix sizes. The arrangement of
connectors and features in switchers with different form
factors is different from what is shown in figure 2-2.
N The CrossPoint 450 Plus switchers are housed in
enclosures that range from 8U to 10U (figure 2-1) to
support their different video format and matrix sizes.
The CrossPoint Ultra switchers are housed in enclosures
that range from 3U to 6U to support their different video
format and matrix sizes.
Smaller matrix sizes within a form factor have fewer input
and/or output connectors. The arrangement of connectors
and features in switchers with different form factors is
different from what is shown in figure 2-1.
3
4
1
2
3
4
1
2
3
4
1
2
3
5
6
7
8
5
6
7
8
5
6
7
8
5
6
7
8
5
6
7
8
10
11
12
9
10
11
12
9
10
11
12
9
10
11
12
9
10
11
12
13
14
15
16
13
14
15
16
13
14
15
16
13
14
15
16
13
14
15
16
17
18
19
20
17
18
19
20
17
18
19
20
17
18
19
20
17
18
19
20
21
22
23
24
21
22
23
24
21
22
23
24
21
22
23
24
21
22
23
24
25
26
27
28
25
26
27
28
25
26
27
28
25
26
27
28
25
26
27
28
29
30
31
32
29
30
31
32
29
30
31
32
29
30
31
32
29
30
31
32
INPUTS
INPUTS
RED
GREEN
BLUE
OUTPUTS
OUTPUTS
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
13
INPUTS
Ω
Ω
OUTPUTS
1
INPUTS
Ω
H
12345678
Ω
HV SYNC
12345678
OUTPUTS
3
4
1
2
3
4
1
2
3
4
5
6
7
8
5
6
7
8
5
6
7
8
9
10
11
12
9
10
11
12
9
10
11
12
14
15
16
13
14
15
16
13
14
15
16
13
2
3
4
5
6
7
8
9
10
11
12
14
15
16
1
18
19
20
17
18
19
20
17
18
19
20
17
18
19
20
17
18
19
20
21
22
23
24
21
22
23
24
21
22
23
24
21
22
23
24
21
22
23
24
25
26
27
28
25
26
27
28
25
26
27
28
25
26
27
28
25
26
27
28
29
30
31
32
29
30
31
32
29
30
31
32
29
30
31
32
29
30
31
32
L
1
R
L
2
R
L
3
R
L
4
R
L
5
R
L
6
R
L
7
R
L
8
R
L
9
R
L
10
R
L
11
R
L
12
R
L
13
R
L
14
R
L
15
R
L
16
R
L
17
R
L
18
R
L
19
R
L
20
R
L
21
R
L
22
R
L
23
R
L
24
R
L
25
R
L
26
R
L
27
R
L
28
R
L
29
R
L
30
R
L
31
R
L
32
R
L
1
L
2
L
3
L
4
L
5
L
6
L
7
L
8
R
L
9
R
L
10
R
L
11
R
L
12
R
L
13
R
L
14
R
L
15
R
L
16
R
L
9
L
10
L
11
L
12
L
13
L
14
L
15
L
16
R
L
25
R
L
26
R
L
27
R
L
28
R
L
29
R
L
30
R
L
31
R
L
32
R
®
11
US
R
R
R
O
U
T
P
U
T
S
LISTED
1T23
I.T.E.
4
6
10
14
18
22
7
11
15
19
23
27
31
3
7
11
15
19
23
27
31
4
8
12
16
20
24
28
32
4
8
12
16
20
24
28
32
1
5
9
13
17
21
25
29
1
5
9
13
17
21
25
29
I
N
P
U
T
S
Y
O
U
T
P
U
T
S
2
6
10
14
18
22
26
30
3
7
11
15
19
23
27
31
4
8
12
16
20
24
28
32
L
1
R
L
2
R
L
3
R
L
4
R
L
5
R
L
6
R
L
7
R
L
8
R
L
17
R
L
18
R
L
19
R
L
20
R
L
21
R
L
22
R
L
23
R
L
24
R
L
1
R
L
2
R
L
3
R
L
4
R
L
5
R
L
6
R
L
7
R
L
8
R
L
17
R
L
18
R
L
19
R
L
20
R
L
21
R
L
22
R
L
23
R
L
24
R
I
N
P
U
T
S
O
U
T
P
U
T
S
C
INPUTS
2
6
10
14
18
22
26
30
3
7
11
15
19
23
27
31
4
8
12
16
20
24
28
32
L
9
R
L
10
R
L
11
R
L
12
R
L
13
R
L
14
R
L
15
R
L
16
R
L
25
R
L
26
R
L
27
R
L
28
R
L
29
R
L
30
R
L
31
R
L
32
R
®
5
US
OUTPUTS
L
9
R
L
10
R
L
11
R
L
12
R
L
13
R
L
14
R
L
15
R
L
16
R
L
25
R
L
26
R
L
27
R
L
28
R
L
29
R
L
30
R
L
31
R
L
32
R
LISTED
1T23
I.T.E.
2
5
11
10 8
9
Figure 2-2 — MAV Plus 3232 SVA matrix switcher
9
2
1
®
8
Figure 2-1 — CrossPoint 450 Plus 3232 HVA rear panel
2-2
30
30
10
2
3
5
4
OUTPUTS
7
6
9
8
10
12
11
1
3
2
5
4
7
6
8
LAN
LINK ACT
R
29
26
INPUTS
RS 232/422
R
R
25
22
RESET
ETHERNET
R
R
21
18
4
REMOTE
100-240V ~ 50/60Hz 1.2A MAX
R
R
17
14
2
1
R
13
10
1
I
N
P
U
T
S
ANAHEIM, CA
R
9
6
1
3
V SYNC
17
R
5
2
3
100-240V
50/60Hz
1.2A MAX.
R
1
OUTPUTS
2
1
29
4
9
INPUTS
25
26
RESET SYNC
2
21
CrossPoint / MAV Matrix Switchers • Installation
Refer also to the CrossPoint 450 Plus / CrossPoint Ultra / MAV Plus User’s Manual at www.extron.com.
2
3
4
6
5
8
7
9
10
11
12
1
2
3
4
5
6
7
8
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
LISTED
US 1T23
I.T.E.
11
6
RESET SYNC
1
17
7
RS232/RS422
4
13
9
LAN
3
5
ANAHEIM, CA
REMOTE
2
1
2
RS232/RS422
1
1
REMOTE
9 8
Figure 2-3 — MAV Plus 128 AV RCA matrix switcher
CrossPoint / MAV Matrix Switchers • Installation
Refer also to the CrossPoint 450 Plus / CrossPoint Ultra / MAV Plus User’s Manual at www.extron.com.
2-3
Installation, cont’d
Making connections and rear panel settings
d
C Turn off power to the input and output devices, and
disconnect their power cords.
a
2
Tip
Sleeve
Unbalanced Input
1
(high impedance)
Figure 2-4 — Audio input connector wiring
2
e
1
2
Connections for balanced and unbalanced audio outputs
(most audio models) — Connect balanced or unbalanced stereo
audio output devices to these 5-pole captive screw connectors.
Tip
NO GROUND HERE.
Sleeve(s)
Tip
1
NO GROUND HERE.
Unbalanced Output
2
switches for inputs 1 through 8.
CrossPoint Ultra switchers have Sync termination
switches for inputs 1 through 4.
The matrix switchers have two sets of sync termination
switches; one for horizontal or combined sync and a second
set for vertical sync.
510 ohms — The default position, suitable for most video.
75 ohms — Typically required only for an input with non-TTL
sync (greater than 5 V p-p).
Tip
Ring
Sleeve(s)
Tip
Ring
Balanced Output
CAUTION For unbalanced audio, connect the
sleeve(s) to the ground contact.
DO NOT connect the sleeve(s) to
the negative (-) contacts).
Figure 2-5 — Audio output connector wiring
N CrossPoint 450 Plus switchers have Sync termination
(high impedance)
1
c
Balanced Input
2
Sync termination switches (CrossPoint switchers) —
Set the switches as necessary to condition non-TTL sync levels
greater than 5 Vp-p. Sync termination enables the sync to be
properly passed from input to selected output(s).
Tip
Ring
Sleeve (s)
Tip
Ring
R
Video outputs — Connect RGBHV, RGBS, RGsB,
RsGsBs, component/HDTV video, S-video, or
composite video displays, as appropriate to your
switcher model's video format and matrix size.
Tip
Sleeve
L
b
Video inputs — Connect RGBHV, RGBS, RGsB,
RsGsBs, component/HDTV video, S-video, or
composite video sources, as appropriate to your
switcher model's video format and matrix size.
1
R
Connect the input or output on each video plane
to the corresponding connector in the correct
group. Refer to the CrossPoint 450 Plus /
CrossPoint Ultra / MAV Plus Switcher
Manual to connect the various video formats to
and from the various models if you are not sure.
audio inputs to these 5-pole captive screw connectors.
L
N Video connectors are grouped by video plane.
Connections for balanced and unbalanced audio inputs (most
audio models) — Connect balanced or unbalanced stereo
f
Connections for unbalanced audio inputs
(MAV Plus 126 AV RCA) — Connect unbalanced stereo
audio inputs to each pair (left and right) of female
RCA connectors.
g
Connections for unbalanced audio outputs
(MAV Plus 126 AV RCA) — Connect unbalanced stereo
audio output devices to each pair (left and right) of
female RCA connectors.
N An input that produces an out of sync display, a display
that is rolling vertically and/or tearing horizontally, could
indicate a non-TTL sync input. If you are not sure, check
the specifications in the user’s manual for the input device.
2-4
CrossPoint / MAV Matrix Switchers • Installation
Refer also to the CrossPoint 450 Plus / CrossPoint Ultra / MAV Plus User’s Manual at www.extron.com.
CrossPoint / MAV Matrix Switchers • Installation
Refer also to the CrossPoint 450 Plus / CrossPoint Ultra / MAV Plus User’s Manual at www.extron.com.
2-5
Installation, cont’d
port — If desired, connect a control
h Remote
system or computer to the rear panel Remote
5
RS-232/RS-422 port.
1
9
6
Front Panel Configuration Port
(Matrix Sizes up to 1616, MAV Plus 32 A, and
MAV Plus 248 A)
N Serial port defaults: RS-232, 9600 baud,
12
no parity, 8-bit, 1 stop bit, no flow control.
RS-232
RS-422
Matrix Sizes:
84 — 1616
Matrix Sizes:
All Models MAV Plus 248 / 328 A 2412 — 3232
Pin#
1
2
3
4
5
6
7
8
9
Pin Function
— Not used
TX Transmit
RX Receive
— Not used
Gnd Ground
— Not used
— Not used
— Not used
— Not used
Pin
—
TX–
RX–
—
Gnd
—
RX+
TX+
—
Function
Not used
Transmit –
Receive –
Not used
Ground
Not used
Receive +
Transmit +
Not used
Pin
TX+
TX–
RX+
RX–
Gnd
—
—
—
—
Function
Transmit +
Transmit –
Receive +
Receive –
Ground
Not used
Not used
Not used
Not used
i
LAN port — If desired, connect a network WAN or LAN hub, a
control system, or computer to the Ethernet RJ-45 port.
•
Network connection — Wire as a patch (straight) cable.
•
Computer or control system connection — Wire the
interface cable as a crossover cable.
CONTROL
ENTER
PRESET
VIEW
I/O
ESC
VIDEO
AUDIO
CONFIG
CROSSPOINT ULTRA SERIES
ULTRA-WIDEBAND MATRIX SWITCHER WITH ADSP™
Figure 2-7 — Front panel configuration port
l
Configuration port — If desired, connect a control system
or computer to the front panel Configuration (RS-232) port.
Use an optional 9-pin D to 2.5 mm mini jack TRS RS-232
cable, part #70-335-01.
N The factory default IP address is 192.168.254.254.
j
External Sync (MAV Plus) — If desired, attach an external sync
timing device to the external sync connector.
BBG 6 A
12V
0.5A MAX
1 KHZ AUDIO
+4dBu
1
R
L
NTSC
BLACK BURST/COLOR BAR
/AUDIO GENERATOR
POWER
1
3
5
4
6
ON
1 2 3
-10dBV PAL
BLACKBURST/
COLORBAR
2
Extron
BBG 6 A
Black Burst Color Bar
Audio Generator
BLACKBURST
OUT
Connect to
MAV Plus.
EXT
SYNC
Terminate cable
or connect to
another device.
Figure 2-6 — External Sync connection
k
2-6
Power — Plug the switcher into a grounded AC source.
CrossPoint / MAV Matrix Switchers • Installation
Refer also to the CrossPoint 450 Plus / CrossPoint Ultra / MAV Plus User’s Manual at www.extron.com.
CrossPoint / MAV Matrix Switchers • Installation
Refer also to the CrossPoint 450 Plus / CrossPoint Ultra / MAV Plus User’s Manual at www.extron.com.
2-7
Installation, cont’d
CrossPoint / MAV Matrix Switchers
3
Chapter Three
Front Panel Operation
Creating a Tie
Saving or Recalling a Preset
Setting the Front Panel Locks (Executive Modes)
Viewing and Adjusting the Audio Level
Viewing Ties (and Muting Outputs)
2-8
CrossPoint / MAV Matrix Switchers • Installation
Refer also to the CrossPoint 450 Plus / CrossPoint Ultra / MAV Plus User’s Manual at www.extron.com.
Front Panel Operation
Saving or Recalling a Preset
1.
Save a preset — Press and hold the Preset button until it
flashes.
Recall a preset — Press and release the Preset button.
INPUTS
1 2 3 4 5 6 7 8 9 10 11 12
CONTROL
1 2 3 4 5 6 7 8
ENTER
OUTPUTS
PRESET
VIEW
I/O
ESC
VIDEO
AUDIO
CONFIG
Save a
preset
CROSSPOINT ULTRA SERIES
ULTRA-WIDEBAND MATRIX SWITCHER WITH ADSP™
PRESET
Press and hold.
Preset button blinks.
N The video selection button is labeled “RGBHV” on the
CrossPoint switchers and “Video” on the MAV Plus
switchers. The two labels are used interchangeably in this
guide.
Recall a
preset
PRESET
Creating a Tie
Press and release the Esc button to clear any input button,
output button, or control button indicators that may be lit.
2.
Press and release the Video and/or Audio I/O button(s) to
select or deselect video and/or audio as desired.
I/O
Green when selected.
Off when deselected.
Red when selected.
Off when deselected.
RGBHV AUDIO
Press and release.
•
All input and output buttons with
assigned presets light red.
The configuration data at assigned
preset locations will be overwritten.
1
2.
2
The button lights to indicate the selection.
5
6
The button blinks red to indicate that
this preset is selected to save or recall.
3.
1
ENTER
The Enter button blinks
red to indicate the need to
activate the save or recall.
Press and release the Enter button.
5
4.
4
Press and release the desired input or output button.
selecting only the Video button or only the Audio button.
Press and release the desired input button.
3
17 18 19 20 21 22
N Audio or video can be broken away (tied by itself) by
3.
PRESET
Preset button lights.
•
1.
PRESET
2 seconds
Press and release the desired output button(s).
Amber indicates RGBHV/video and audio tie.
Green indicates RGBHV/video only tie.
Red indicates audio only tie.
3
5.
3-2
4
8
ENTER
Green indicates the
need to confirm the
change.
Press and release the Enter button. All button indicators
turn off.
CrossPoint / MAV Matrix Switchers • Front Panel Operation
Refer also to the CrossPoint 450 Plus / CrossPoint Ultra / MAV Plus User’s Manual at www.extron.com.
CrossPoint / MAV Matrix Switchers • Front Panel Operation
Refer also to the CrossPoint 450 Plus / CrossPoint Ultra / MAV Plus User’s Manual at www.extron.com.
3-3
Front Panel Operation, cont’d
Setting the Front Panel Locks (Executive Modes)
The matrix switcher has three levels of front panel security lock
that limit the operation of the switcher from the front panel. The
three levels are:
•
Lock mode 0 — The front panel is completely unlocked.
•
Lock mode 1 — All changes are locked from the front
panel (except for setting Lock mode 2). Some functions
can be viewed.
•
Lock mode 2 — Basic functions are unlocked. Advanced
features are locked and can be viewed only.
Basic features consist of:
m
Making ties
m
Saving and recalling presets
m
Setting input audio gain and attenuation
m
Changing Lock modes
Selecting Lock mode 2 or toggling between
mode 2 and mode 1
N If the switcher is in Lock mode 0 or mode 1, this procedure
selects mode 2.
If the switcher is in Lock mode 2, this procedure selects
mode 1.
Toggle the lock on and off by pressing and holding the Video
button and the Audio button for approximately 2 seconds.
Press and hold
simultaneously.
I/O
VIDEO
AUDIO
2 seconds
I/O
Advanced features consist of:
m
Setting video and audio output mutes
m
Setting audio output volume
N The switcher is shipped from the factory in Lock mode 2.
Selecting Lock mode 2 or toggling between
mode 2 and mode 0
VIDEO
AUDIO
The buttons blink twice.
Release the buttons.
Viewing and Adjusting the Audio Level
1.
Press and hold the Audio button until it flashes.
N If the switcher is in Lock mode 0 or mode 1, this procedure
selects mode 2.
If the switcher is in Lock mode 2, this procedure selects
mode 0 (unlocks the switcher).
Toggle the lock on and off by pressing and holding the
Enter button, the Video button, and the Audio button for
approximately 2 seconds.
AUDIO
ENTER
VIDEO
AUDIO
Press and
Hold
AUDIO
Audio button blinks.
2.
Press an input or output button. Refer to the
CrossPoint 450 Plus / CrossPoint Ultra / MAV Plus Switcher
Manual, chapter 3, “Operation”, to read the displayed
value.
3.
Increase/decrease the level or volume by pressing the Esc
(>) and View (<) buttons.
4.
Press and release the Audio button to exit.
Press and hold simultaneously.
I/O
2 seconds
2 seconds
I/O
ENTER
VIDEO
AUDIO
The buttons blink twice.
Release the buttons.
3-4
CrossPoint / MAV Matrix Switchers • Front Panel Operation
Refer also to the CrossPoint 450 Plus / CrossPoint Ultra / MAV Plus User’s Manual at www.extron.com.
CrossPoint / MAV Matrix Switchers • Front Panel Operation
Refer also to the CrossPoint 450 Plus / CrossPoint Ultra / MAV Plus User’s Manual at www.extron.com.
3-5
Front Panel Operation, cont’d
Viewing Ties (and Muting Outputs)
1.
Press the View button. Output buttons light for outputs
that have no ties established.
N If the Audio button blinks, audio is broken away (switched
separately from video).
N If an output button blinks, that output is muted. To
toggle mute on and off, press and hold the output button
for 2 seconds.
2.
Press an input button. The buttons for all tied outputs
light (amber for video and audio, green for video only, and
red for audio only).
3.
Press an output button. The buttons for the tied input and
all tied outputs light.
4.
Press the View button. All input and output buttons return
to an unlit state.
CrossPoint / MAV Matrix Switchers
4
Chapter Four
Remote Control
Selected SIS Commands
Installing and Starting the Control Program
Accessing the HTML Pages
3-6
CrossPoint / MAV Matrix Switchers • Front Panel Operation
Refer also to the CrossPoint 450 Plus / CrossPoint Ultra / MAV Plus User’s Manual at www.extron.com.
Remote Control
Selected SIS Commands
The switchers have Simple Instruction Set (SIS ) commands that
you can use for operation and configuration. You can run these
commands from a PC connected to either of the switcher’s serial
ports or the Ethernet port. See h, i, and l, on pages 2-6 and
2-7, for connection information.
™
Establishing a network (Ethernet) connection
Establish a network connection as follows:
1.
Open a TCP socket to port 23 using the switcher’s IP
address.
N The factory default IP address is 192.168.254.254.
The switcher responds with a copyright message including
the date, the name of the product, firmware version, part
number, and the current date/time.
N If the switcher is not password-protected, the device is now
ready to accept SIS commands.
N If the switcher is password-protected, a password
prompt appears.
2.
If the switcher is password protected, enter the appropriate
password.
If the password is accepted, the switcher responds with
Login User or Login Administrator.
If the password is not accepted, the Password prompt
reappears.
Connection timeouts
The Ethernet link times out and disconnects after a designated
period of time of no communications. By default, this timeout
value is set to five minutes but the value can be changed. See
the Set Connection Timeout command on page 4-8.
Number of connections
A switcher can have up to 200 simultaneous TCP connections,
including all HTTP sockets and Telnet connections. When
the connection limit is reached, the switcher accepts no new
connections until some have been closed. No error message or
indication is given that the connection limit has been reached.
To maximize performance of your switcher, the number of
connections should stay low and unnecessary open sockets
should be closed.
Verbose mode
Telnet connections to a switcher can be used to monitor
for changes that occur on the switcher, such as front panel
operations and SIS commands from other Telnet sockets or a
serial port. For a Telnet session to receive change notices from
the switcher, the Telnet session must be in verbose mode 3. See
the Verbose Mode command on page 4-8. In verbose mode 3,
the Telnet socket reports changes in messages that resemble SIS
command responses.
Host-to-switcher instructions
The switcher accepts SIS (Simple Instruction Set) commands
through either serial port. SIS commands consist of one or more
characters per command field. They do not require any special
characters to begin or end the command character sequence.
Each switcher response to an SIS command ends with a carriage
return and a line feed (CR/LF = ]), which signals the end of
the response character string. A string is one or more characters.
N The table that begins on the next page is a partial list
of SIS commands. For a complete listing, refer to the
CrossPoint 450 Plus / CrossPoint Ultra / MAV Plus
Switcher Manual, chapter 4, “Programmer’s Guide”.
N Extron recommends leaving the default timeout at five
minutes and periodically issuing the Query (Q) command
to keep the connection active or disconnecting the socket
and reopening the connection when necessary.
4-2
CrossPoint / MAV Matrix Switchers • Remote Control
Refer also to the CrossPoint 450 Plus / CrossPoint Ultra / MAV Plus User’s Manual at www.extron.com.
CrossPoint / MAV Matrix Switchers • Remote Control
Refer also to the CrossPoint 450 Plus / CrossPoint Ultra / MAV Plus User’s Manual at www.extron.com.
4-3
ASCII command
Response
(switcher to host)
Additional description
Create ties
CrossPoint / MAV Matrix Switchers • Remote Control
Refer also to the CrossPoint 450 Plus / CrossPoint Ultra / MAV Plus User’s Manual at www.extron.com.
(host to switcher)
N • Commands can be entered back-to-back in a string, with no spaces. For example: 1*1!02*02&003*003%4*24$.
•The matrix switchers support 1-, 2-, and 3-digit numeric entries (1*1!, 02*02&, or 003*003%).
N The & tie command for RGB and the % tie command for video can be used interchangeably.
N The & read tie command for RGB and the % read tie command for video can be used interchangeably.
Tie input X! to output X@, video
and audio
Example:
X!*X@!
OutX@•InX!•All]
Tie input X!‘s video and audio to output X@.
1*3!
Out03•In01•All]
Tie input X! to output X@, RGBHV
only
Example
(see 2nd Note, above):
X!*X@&
OutX@•InX!•RGB]
Tie input 1 video and audio to output 3.
Audio breakaway.
10*4&
Out04•In10•RGB]
Tie input 10 RGB to output 4.
Tie input X! to output X@, video
only
Example
(see 2nd Note, above)
X!*X@%
OutX@•InX!•Vid]
Audio breakaway.
7*5%
Out05•In07•Vid]
Tie input 7 video to output 5.
Tie input X! to output X@, audio
only
Example:
X!*X@$
OutX@•InX!•Aud]
Audio breakaway.
24*04$
Out04•In24•Aud]
Tie input 24 audio to output 4.
Read RGB output tie
X@&
X@%
X@$
X!]
X!]
X!]
RGBHV input X! is tied to output X@.
Read video output tie
Read audio output tie
N
X! = Input number
X@ = Output number
Command
Video input X! is tied to output X@.
Audio input X! is tied to output X@.
00 – (maximum number of inputs for your model) (00 = untied)
01 – (maximum number of outputs for your model)
ASCII command
CrossPoint / MAV Matrix Switchers • Remote Control
Refer also to the CrossPoint 450 Plus / CrossPoint Ultra / MAV Plus User’s Manual at www.extron.com.
(host to switcher)
Response
(switcher to host)
Additional description
Video and audio mute commands
RGB/video mute
Read RGB/video mute
X@*1B
X@*0B
X@B
Global RGB/video mute
1*B
Global RGB/video unmute
0*B
Audio mute
X@*1Z
Audio unmute
Read audio mute
X@*0Z
X@Z
Global audio mute
1*Z
Global audio unmute
0*Z
View output mutes
EVM}
RGB/video unmute
Example:
VmtX@*1]
Mute output X@ RGB (video off).
VmtX@*0]
Unmute output X@ RGB (video on).
1 = mute on, 0 = mute off.
X#]
Vmt1]
Vmt0]
AmtX@*1]
AmtX@*0]
X#]
Amt1]
Amt0]
X$1, X$2, ... X$n]
Mute all RGB outputs.
Unmute all RGB outputs.
Mute output X@ audio (audio off).
Unmute output X@ audio (audio on).
1 = mute on, 0 = mute off.
Mute all audio outputs.
Unmute all audio outputs.
Each X$ response is the mute status of an
output, starting from output 1.
n = the maximum number of outputs for this
model.
Mut02202000000000000000000000000000]
Output 2, 3, and 5 audio is muted. All other
outputs are unmuted.
N The “Mut” portion of the response appears only when the switcher is in Verbose mode 3. See the Verbose mode command on page 4-8.
CrossPoint 450 Plus 3232 HVA
N
X@ = Output number
X# = Mute
4-5
X$ = Video/audio mute:
EVM}
01 – (maximum number of outputs for your model)
0 = off (unmuted)
1 = on (muted)
0 = no mutes
1 = video mute
2 = audio mute
Remote Control, cont’d
4-4
Command
ASCII command
Response
Additional description
(switcher to host)
Set the audio volume to a specific
value
Example:
X@*X%V
OutX@•VolX%]
1*50v
Out01•Vol50]
Set output 1 volume to 79%.
Increment volume
X@+V
1+V
OutX@•VolX%]
Increase volume by 1 step.
Audio output volume
CrossPoint / MAV Matrix Switchers • Remote Control
Refer also to the CrossPoint 450 Plus / CrossPoint Ultra / MAV Plus User’s Manual at www.extron.com.
(host to switcher)
Example:
Decrement volume
Read output volume
Out01•Vol51]
X@-V
X@V
OutX@•VolX%]
Decrease volume by 1 step.
X%]
Save and recall presets
N • If you try to recall a preset that is not saved, the matrix switcher responds with the error code E11.
•The following characters are invalid in preset names: + - , ` @ = [ ] { } ‘ “ ; : | \ and ?.
Save current configuration as a
Command character is a comma.
SprX^]
X^,
global preset
Example:
Save current ties as preset 9.
Spr09]
9,
Recall a global preset
Example:
N
X^.
5.
X@ = Output number
X% = Volume
X^ = Preset number
Command
RprX^]
Command character is a period.
Rpr05]
Recall preset 5, which becomes the current
configuration.
01 – (maximum number of outputs for your model)
0 – 64 (1 dB/step except for 0-to-1, which is 22 dB) (default = 64 [0 dB])
00 - 32 (00 = current configuration)
ASCII command
CrossPoint / MAV Matrix Switchers • Remote Control
Refer also to the CrossPoint 450 Plus / CrossPoint Ultra / MAV Plus User’s Manual at www.extron.com.
(host to switcher)
Response
(switcher to host)
Additional description
Lock (executive) modes
N See “Setting the front panel locks (Executive modes)” on page 3-3 for more information on the Lock modes.
Lock all front panel functions
1X
Enable Lock mode 1.
Exe1]
Lock advanced front panel functions
2X
Exe2]
Enable Lock mode 2.
Unlock all front panel functions
0X
Exe0]
Enable Lock mode 0.
View lock status
X
X&]
Information request
I
VX*XX(•AX*XX(]
Example:
MAV Plus 3216 HDA
Request part number
I
V32X16•A32X16]
N
Query controller firmware version
Q
X1)]
X1!]
1.23]
Information requests
Example:
N
X& = Lock mode
X* = Inputs
X( = Outputs
X1) = Part number
Q
VX*XX( is the video matrix size.
AX*XX( is the audio matrix size.
The factory-installed controller firmware
version is 1.23 (sample value only).
0, 1, or 2
Total number of inputs for this switcher
Total number of outputs for this switcher
See the CrossPoint 450 Plus / CrossPoint Ultra / MAV Plus User’s Manual, available on the Extron disk or at www.extron.com for a complete list of part numbers.
X1! = Firmware version number to second decimal place (x.xx)
Remote Control, cont’d
4-6
Command
4-7
ASCII command
Response
(switcher to host)
EX1#CI}
ECI}
EX1#CS}
ECS}
EX1#CG}
ECG}
EX1$DH}
EDH}
EX1%CV}
ECV}
E0*X1^TC}
E0TC}
E1*X1^TC}
E1TC}
IpiX1#]
X1#]
IpsX1#]
X1#]
IpgX1#]
X1#]
IdhX1$]
X1$]
VrbX1%]
X1%]
Pti0*X1^]
X1^]
Pti1*X1^]
X1^]
Additional description
IP setup
CrossPoint / MAV Matrix Switchers • Remote Control
Refer also to the CrossPoint 450 Plus / CrossPoint Ultra / MAV Plus User’s Manual at www.extron.com.
(host to switcher)
Set IP address
Read IP address
Set subnet mask
Read subnet mask
Set gateway IP address
Read gateway IP address
Set DHCP on or off
Read DHCP on/off status
Set verbose mode
Read verbose mode
Configure current port timeout
Read current port timeout
Configure global IP port timeout
Read global IP port timeout
N
X1# = IP address
X1$ = DHCP
X1% = Verbose mode
X1^ = Port timeout interval
###.###.###.###
0 =1 off, 1 = on
0 = clear/none (default for Telnet connection)
1 = verbose mode (default for RS-232/RS-422 connection)
2 = tagged responses for queries
3 = verbose mode and tagged for queries
1 (= 10 seconds) - 65000 (default is 30 = 300 seconds = 5 minutes)
Remote Control, cont’d
4-8
Command
Installing and Starting the Control Program
Another way to operate the switcher is via the Windows®-based
Matrix Switchers Control Program. This program is contained
on the Extron Software Products Disk (included with the
switcher). Run this program on a PC connected to either of the
switcher’s serial ports or the Ethernet port. See h, i, and l,
on pages 2-6 and 2-7, for connection information. The program
must be installed on a Windows-based computer and cannot be
run from the disk.
N For details on operating the program, refer to the
CrossPoint 450 Plus / CrossPoint Ultra / MAV Plus
Switcher Manual, chapter 5, “Matrix Software”.
Installing the program
1.
Insert the disk into the drive. The installation program
should start automatically.
The Extron software disk window appears.
N If the installation program does not self-start, run
Launch.exe from the disk.
2.
Click the Software tab.
3.
Scroll to the Matrix Switchers program and click Install.
CrossPoint / MAV Matrix Switchers • Remote Control
Refer also to the CrossPoint 450 Plus / CrossPoint Ultra / MAV Plus User’s Manual at www.extron.com.
4-9
Remote Control, cont’d
4.
Follow the on-screen instructions. The installation
program creates a C:\Program Files\Extron\
Matrix_Switchers directory and an “Extron Electronics\
Matrix Switchers” group folder. It installs the following
four programs:
•
•
•
•
MATRIX Switcher+ Control Program
MATRIX Switcher+ Help
Uninstall MATRIX Switcher
Check for Matrix Updates
Starting the program
1.
Click Start > Programs > Extron Electronics > Matrix
Switchers > MATRIX Switcher + Control Pgm.
The Comm Port Selection window appears.
3.
If you selected IP [LAN] in step 2, the IP Connection
window appears.
a. Examine the Matrix IP Address field, which displays
the last Matrix IP address entered.
If necessary, enter the correct IP address in the field.
N 192.168.254.254 is the factory-specified default value for
this field.
b. If the switcher is password protected, enter the
appropriate administrator or user password in the
Password field.
c. Click Connect. The Matrix Switchers Control Program
is ready for operation.
2.
Choose the comm (serial) port that is connected to the
switcher or IP [LAN].
N For a comm port, check the baud rate displayed in the
comm port selection window. If you need to change the
baud rate, click the Baud button and double-click the
desired baud rate.
4-10
Click OK.
If you selected a serial port in step 2, the Matrix Switchers
Control Program is ready for operation.
CrossPoint / MAV Matrix Switchers • Remote Control
Refer also to the CrossPoint 450 Plus / CrossPoint Ultra / MAV Plus User’s Manual at www.extron.com.
CrossPoint / MAV Matrix Switchers • Remote Control
4-11
Refer also to the CrossPoint 450 Plus / CrossPoint Ultra / MAV Plus User’s Manual at www.extron.com.
Remote Control, cont’d
Accessing the HTML Pages
Another way to operate the switcher is via its factory-installed
HTML pages, which are always available and cannot be erased
or overwritten. The switcher’s HTML pages are accessible
through its LAN port, connected via a LAN or WAN, using a
web browser such as Microsoft Internet Explorer. See i on
page 2-6, for connection information.
N A User name entry is not required.
5.
Enter the appropriate administrator or user password in
the Password field and click OK.
6.
The switcher downloads the HTML start-up page. The
switcher is ready for operation via HTML remote control.
Loading the start-up page
N If your Ethernet connection to the matrix switcher is
unstable, try turning off the proxy server in your Web
browser. In Microsoft Internet Explorer, click Tools >
Internet Options > Connections > LAN Settings,
uncheck the Use a proxy server... box, and then click
OK.
N For details on operating the switcher via HTML pages,
refer to the CrossPoint 450 Plus / CrossPoint Ultra /
MAV Plus Switcher Manual, chapter 6, “HTML
Operation”.
1.
Start the Web browser program.
2.
Click in the browser’s Address field.
3.
Enter the Matrix IP address in the browser’s Address field.
N 192.168.254.254 is the factory-specified default value for
this field.
4.
Press the keyboard Enter key. The switcher checks to see if
it is password protected.
If the switcher is not password protected, it checks and
downloads the HTML start-up page. The switcher is ready
for operation via HTML remote control.
If the switcher is password protected, the switcher
downloads the Enter Network Password page.
4-12
CrossPoint / MAV Matrix Switchers • Remote Control
Refer also to the CrossPoint 450 Plus / CrossPoint Ultra / MAV Plus User’s Manual at www.extron.com.
CrossPoint / MAV Matrix Switchers • Remote Control
4-13
Refer also to the CrossPoint 450 Plus / CrossPoint Ultra / MAV Plus User’s Manual at www.extron.com.
Remote Control, cont’d
4-14
CrossPoint / MAV Matrix Switchers • Remote Control
Refer also to the CrossPoint 450 Plus / CrossPoint Ultra / MAV Plus User’s Manual at www.extron.com.