Zenith P50W28A Service manual

SERVICE MANUAL
Product Type:
Chassis:
Manual Series:
Manual Part #:
Model Line:
Product Year:
Model Series:
P50W28A
PLASMA
RF-02KE
2002
CONTENTS
Description of Controls .................................................4
Adjustment Instructions ...............................................17
Diagrams ...................................................................20
Parts List ...................................................................23
Schematics ....................................................................
Printed Circuit Boards ....................................................
Published June 2002
by Technical Publications
Zenith Electronics Corporation
201 James Record Road
Huntsville, Alabama 35824-1513
Copyright © 2002 by Zenith Electronics Corporation
Printed in Korea
PRODUCT SAFETY GUIDELINES
IMPORTANT SAFETY NOTICE
This manual was prepared for use only by properly trained audio-visual service
technicians.
When servicing this product, under no circumstances should the original design
be modified or altered without permission from Zenith Electronics Corporation.
All components should be replaced only with types identical to those in the
original circuit and their physical location, wiring and lead dress must conform
to original layout upon completion of repairs.
CAUTION: Do not attempt to modify this product in any way.
Never perform customized installations without manufacturer’s
approval.
Unauthorized modifications will not only void the warranty, but may
lead to property damage or user injury.
Service work should be performed only after you are thoroughly familiar with
these safety checks and servicing guidelines.
5. No lead or component should touch a receiving tube or a resistor rated at 1
watt or more. Lead tension around protruding metal surfaces must be avoided.
6. After reassembly of the set, always perform an AC leakage test on all
exposed metallic parts of the cabinet (the channel selector knobs, antenna
terminals, handle and screws) to be sure that set is safe to operate without
danger of electrical shock. DO NOT USE A LINE ISOLATION
TRANSFORMER DURING THIS TEST. Use an AC voltmeter having 5000
ohms per volt or more sensitivity in the following manner: Connect a 1500
ohm, 10 watt resistor, paralleled by a .15 mfd 150V AC type capacitor
between a known good earth ground water pipe, conduit, etc.) and the
exposed metallic parts, one at a time.
Measure the AC voltage across the combination of 1500 ohm resistor and
.15 mfd capacitor. Reverse the AC plug by using a non-polarized adaptor
and repeat AC voltage measurements for each exposed metallic part.
Voltage measured must not exceed 0.75 volts RMS. This corresponds to 0.5
milliamp AC. Any value exceeding this limit constitutes a potential shock
hazard and must be corrected immediately.
TIPS ON PROPER INSTALLATION
GRAPHIC SYMBOLS
The exclamation point within an equilateral triangle is intended to
alert the service personnel to important safety information in the
service literature.
The lightning flash with arrowhead symbol within an equilateral
triangle is intended to alert the service personnel to the presence
of noninsulated “dangerous voltage” that may be of sufficient
magnitude to constitute a risk of electric shock.
A
V
The pictorial representation of a fuse and its rating within an
equilateral triangle is intended to convey to the service personnel
the following fuse replacement caution notice:
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK
OF FIRE, REPLACE ALL FUSES WITH THE SAME TYPE AND
RATING AS MARKED NEAR EACH FUSE.
SERVICE INFORMATION
While servicing, use an isolation transformer for protection from AC line shock.
After the original service problem has been corrected, make a check of the
following:
FIRE AND SHOCK HAZARD
1. Be sure that all components are positioned to avoid a possibility of adjacent
component shorts. This is especially important on items transported to and
from the repair shop.
2. Verify that all protective devices such as insulators, barriers, covers, shields,
strain reliefs, power supply cords, and other hardware have been reinstalled
per the original design. Be sure that the safety purpose of the polarized line
plug has not been defeated.
3. Soldering must be inspected to discover possible cold solder joints, solder
splashes, or sharp solder points. Be certain to remove all loose foreign particles.
4. Check for physical evidence of damage or deterioration to parts and
components, for frayed leads or damaged insulation (including the AC cord),
and replace if necessary.
1. Never install any receiver in a closed-in recess, cubbyhole, or closely fitting
shelf space over, or close to, a heat duct, or in the path of heated air flow.
2. Avoid conditions of high humidity such as: outdoor patio installations where
dew is a factor, near steam radiators where steam leakage is a factor, etc.
3. Avoid placement where draperies may obstruct venting. The customer
should also avoid the use of decorative scarves or other coverings that might
obstruct ventilation.
4. Wall- and shelf-mounted installations using a commercial mounting kit must
follow the factory-approved mounting instructions. A product mounted to a
shelf or platform must retain its original feet (or the equivalent thickness in
spacers) to provide adequate air flow across the bottom. Bolts or screws
used for fasteners must not touch any parts or wiring. Perform leakage tests
on customized installations.
5. Caution customers against mounting a product on a sloping shelf or in a tilted
position, unless the receiver is properly secured.
6. A product on a roll-about cart should be stable in its mounting to the cart.
Caution the customer on the hazards of trying to roll a cart with small casters
across thresholds or deep pile carpets.
7. Caution customers against using a cart or stand that has not been listed by
Underwriters Laboratories, Inc. for use with its specific model of television
receiver or generically approved for use with TVs of the same or larger screen
size.
8. Caution customers against using extension cords. Explain that a forest of
extensions, sprouting from a single outlet, can lead to disastrous
consequences to home and family.
TABLE OF CONTENTS
DESCRIPTION OF CONTROLS ...........................................4
SPECIFICATIONS.................................................................7
EXTERNAL EQUIPMENT VIEWING SETUPS .....................9
EXTERNAL CONTROL DEVICE SETUP............................11
IR CODE(NEC FORMAT) ...................................................16
ADJUSTMENT INSTRUCTION...........................................17
BLOCK DIAGRAM...............................................................20
EXPLODED VIEW...............................................................22
EXPLODED VIEW PARTS LIST .........................................23
REPLACEMENT PARTS LIST ............................................24
SCHEMATIC DIAGRAM..........................................................
PRINTED CIRCUIT BOARD ...................................................
DESCRIPTION OF CONTROLS
Monitor Controls
Front Panel Controls
VOL.
ON/OFF
MENU INPUT SELECT
INPUT SELECT Button
Power Standby Indicator
Illuminates red in standby mode,
Illuminates green when the
Monitor is turned on
Main Power Button
MENU Button
Remote Control Sensor
VOLUME (F,G) Buttons
E, D
Buttons
Connection Options
Back Connection Panel
EXTERNAL SPEAKER (8Ω)
1
Y
R AUDIO L (MONO)
( )R( )
AC INPUT
2
AUDIO
INPUT
VIDEO
INPUT
3
S-VIDEO
PB
PR
COMPONENT
(DVD/DTV INPUT)
ON/
OFF
R AUDIO L
AUDIO
INPUT
4
( )L ( )
CONTROL REMOTE RGB1 OUTPUT AUDIO
LOCK CONTROL (PC/DTV OUTPUT) INPUT
5
6
RGB1 INPUT
RGB2 INPUT
RS-232C INPUT
(PC/DTV INPUT) (DIGITAL RGB INPUT) (CONTROL/SERVICE) EXTERNAL SPEAKER
7
8
1
1. EXTERNAL SPEAKER (8 ohm output)
Connect to optional external speaker(s).
* For further information, refer to ‘Speaker & Speaker Stand’
manual.
5. CONTROL LOCK Switch
REMOTE CONTROL
When “CONTROL LOCK” is set to “ON”, Monitor is operated by the external control device.
2. POWER CORD SOCKET
This Monitor operates on an AC power. The voltage is indicated on the Specifications page. Never attempt to operate
the Monitor on DC power.
6. RGB1 OUTPUT (PC/DTV OUTPUT) JACKS
You can watch the RGB1 signal on another monitor, connect RGB1 OUTPUT (PC/DTV OUTPUT) to another monitor’s PC input port.
3. AUDIO/VIDEO INPUT JACKS
Connect audio/video out from external equipment to these
jacks.
S-VIDEO INPUTS (S-VIDEO)
Connect video out from an S-VIDEO VCR to the S-VIDEO
input.
7. AUDIO INPUT/RGB1 INPUT (PC/DTV INPUT)/
RGB2 INPUT (DIGITAL RGB INPUT) JACKS
Connect the monitor output connector from a PC to the
appropriate input port.
4. COMPONENT (DVD/DTV INPUT)/AUDIO INPUT JACKS
8. RS-232C INPUT (CONTROL/SERVICE) PORT
Connect to the RS-232C port on a PC.
DESCRIPTION OF CONTROLS
External Equipment Connections
Monitor External Equipment Connection Panel
EXTERNAL SPEAKER (8Ω)
Y
R AUDIO L (MONO)
( )R( )
AC INPUT
AUDIO
INPUT
AUDIO INPUT
VIDEO
INPUT
S-VIDEO
S-VIDEO
INPUT
VIDEO INPUT
PB
PR
COMPONENT
(DVD/DTV INPUT)
ON/
OFF
R AUDIO L
AUDIO
INPUT
COMPONENT
AUDIO INPUT
COMPONENT
(DVD/DTV INPUT)
( )L ( )
CONTROL REMOTE RGB1 OUTPUT AUDIO
LOCK CONTROL (PC/DTV OUTPUT) INPUT
RGB1 INPUT
RGB2 INPUT
RS-232C INPUT
(PC/DTV INPUT) (DIGITAL RGB INPUT) (CONTROL/SERVICE) EXTERNAL SPEAKER
RGB
AUDIO
INPUT
RS-232C INPUT
RGB2 INPUT
(DIGITAL RGB INPUT)
RGB1 OUTPUT
(PC/DTV OUTPUT) RGB1 INPUT
(PC/DTV INPUT)
DESCRIPTION OF CONTROLS
Remote Control Key Functions
- When using the remote control, aim it at the remote control sensor on the Monitor.
- Under certain conditions or if the IR code from the remote is interrupted, a particular remote function may not occur.
Repeat remote key presses for functions if necessary.
POWER
Switches the Monitor on from
standby or off to standby.
SLEEP
Sets the sleep timer.
APC
Adjusts the factory preset picture
according to the room.
POWER
SLEEP
INPUT SELECT
APC
DASP
ARC
PIP ARC
PIP
TWIN PICTURE
INPUT SELECT
Selects: VIDEO, S-VIDEO, RGB1-2 or
COMPONENT mode.
DASP
Selects the sound appropriate to
your viewing program character:
FLAT, SPORTS, CINEMA, MUSIC, or
USER
ARC
Changes the picture format.
SUB INPUT
SWAP
MENU
MUTE
PIP
Switches the sub picture on or off.
TWIN PICTURE
VOL
OK
VOL
SUB INPUT
Selects the input source for the sub
picture.
SWAP
Exchanges main and sub picture
images.
MUTE
Switches the sound on or off.
MENU
Displays on-screen menus.
Exits the current menu.
Memorizes menu changes.
1
2
3
4
5
6
NUMBER buttons
7
8
9
OK
0
WIN. SIZE
Adjusts the sub picture size.
STOP
P/STILL
REW
PLAY
FF
VCR BUTTONS
REC
WIN.SIZE WIN.POSITION SPLIT ZOOM
ZOOM-/ZOOM+
Enlarges or reduces
the main picture size.
D /E
Select menu options.
F / G (Volume buttons)
Increase/decrease sound level.
Adjusts menu settings.
POWER
WIN.POSITION
Moves the sub picture.
SPLIT ZOOM
Enlarges selected picture section.
PIP ARC
Changes the PIP picture format.
ZOOM -
ZOOM +
Control some video cassette
recorders.
SPECIFICATIONS
Product Specifications
MODEL
P50W28A
Width (inches / mm)
48.2 / 1223
Height (inches / mm)
28.9 / 734
Depth (inches / mm)
4.1 / 105
Weight (pounds / kg)
99.2 / 45
Power requirement
AC120V, 60Hz
Resolution
1366 x 768 (Dot)
Color
16,770,000 (256 steps of each R, G and B)
Operating Temperature Range
32 ~ 104°F (0 ~ 40°C)
Operating Humidity Range
Less than 80%
Maximum Elevation
6561 feet (2000m)
• The specifications shown above may be changed without notice for quality improvement.
SPECIFICATIONS
Monitor Display Specifications
RGB1 Mode
Resolution
640x350
720x400
640x480
800x600
Horizontal
Vertical
Frequency(KHz) Frequency(Hz)
31.468
70.09
37.861
85.08
31.469
70.08
37.927
85.03
31.469
59.94
35.000
37.861
DDC
Resolution
832x624
Horizontal
Vertical
Frequency(KHz) Frequency(Hz)
49.725
74.55
DDC
o
48.363
60.00
o
56.476
70.06
o
60.023
75.02
o
o
68.677
84.99
o
66.66
o
54.348
60.05
o
72.80
o
63.995
70.01
o
37.500
75.00
o
67.500
75.00
o
43.269
85.00
o
77.487
85.05
o
75.000
75.00
o
63.981
60.02
o
79.976
75.02
o
47.700
60.00
o
o
1024x768
1152x864
1280x960
45.913
90.03
53.011
100.04
64.062
120.00
35.156
56.25
o
37.879
60.31
o
59.625
75.02
o
46.875
75.00
o
67.575
84.99
o
53.674
85.06
o
47.700
60.00
56.000
90.00
59.625
75.02
64.016
100.00
67.575
84.99
1280x1024
1360x768
1366x768
RGB2 Mode
Resolution
640x350
720x400
640x480
800x600
832x624
Horizontal
Vertical
Frequency(KHz) Frequency(Hz)
31.468
70.09
DDC
37.861
85.08
31.469
70.08
37.927
85.03
31.469
59.94
o
35.000
66.66
o
37.861
72.80
o
37.500
75.00
o
43.269
85.00
o
35.156
56.25
o
37.879
60.31
o
48.077
72.18
o
46.875
75.00
o
53.674
85.06
o
49.725
74.55
o
o
Resolution
Horizontal
Vertical
Frequency(KHz) Frequency(Hz)
48.363
60.00
1024x768
1152x864
1152x870
1280x960
1280x1024
1360x768
1366x768
Note:
• DOS mode may not work depending on video card if using a DVI-I cable.
DDC
o
56.476
70.06
o
60.023
75.02
o
68.677
84.99
o
54.348
60.05
o
63.995
70.01
o
67.500
75.00
o
77.487
85.05
o
68.681
75.06
o
60.000
60.00
o
75.000
75.00
o
63.981
60.02
o
47.700
60.00
o
59.625
75.02
o
67.575
84.99
o
47.700
60.00
59.625
75.02
67.575
84.99
EXTERNAL EQUIPMENT VIEWING SETUPS
Watching VCR Setup
How to Connect
- When connecting the Monitor to external equipment, match the colors of connecting ports (Video - yellow, Audio (L) - white,
Audio (R) -red).
- Connect the VIDEO INPUT socket (yellow) with the BNC-RCA adapter to the VIDEO INPUT on the Monitor.
- If you have a mono VCR, connect the audio cable from the VCR to the AUDIO (L/MONO) input on the Monitor.
- If you connect an S-VIDEO VCR to the S-VIDEO input, the picture quality is improved; compared to connecting a regular
VCR to the Video input.
- Use the orbiter function to avoid having a fixed image remain on the screen for a long period of time. Typically a frozen still
picture from a VCR.
If a 4:3 picture format is used; the fixed image may remain visible on the screen.
- To avoid picture noise (interference), leave an adequate distance between the VCR and Monitor
How to View
1. Use the INPUT SELECT button on the remote control to select VIDEO.
(If connected to S-VIDEO, select the S-VIDEO external input source.)
2. Insert a video tape into the VCR and press the PLAY button on the VCR. (See VCR owner’s manual)
Watching Cable TV Setup
How to Connect
- After subscribing to a cable TV service from a local provider and installing a converter, you can watch cable TV programming. This monitor cannot display TV programming unless a TV tuner device or cable TV converter box is connected to the
Monitor.
- For further information regarding cable TV service, contact your local cable TV service provider(s).
How to View
1. Use the INPUT SELECT button on the remote control and select VIDEO.
2. Tune to cable service provided channels using the cable box.
Watching External A/V Source Setup
How to Connect
- When connecting the monitor to an external source, match the colors of AUDIO/VIDEO input jacks on the monitor with
the output jacks on the audio/video equipment: Video = yellow, Audio (Left) = white, Audio (Right) = red.
How to View
1. Use the INPUT SELECT button on the remote control to select VIDEO.
2. Operate the corresponding external equipment. See external equipment operating guide.
Watching DVD Setup
How to Connect
• Component Input ports
- Connect DVD video outputs to Y, PB, PR of COMPONENT (DVD/DTV
You can get better picture quality if you conINPUT) and audio outputs to Audio jacks of AUDIO INPUT.
nect a DVD player to the component input
ports indicated below.
- If your DVD only has a S-Video S-video output jack, connect S-Video
of the DVD to S-Video input on the monitor and DVD audio outputs to
Audio jacks of AUDIO INPUT.
Component ports of the
PR
Y
PB
Monitor
How to View
1. Turn on the DVD player, and insert a DVD.
Pr
Y
Pb
2. Use INPUT SELECT button on the remote control to select COMPOVideo output ports
Y
B-Y R-Y
NENT. Refer to the DVD player's manual for operating instructions.
Y
Cb Cr
of DVD player
Y
PB PR
EXTERNAL EQUIPMENT VIEWING SETUPS
Watching DTV Setup
- To watch digitally broadcast programs, purchase/connect a digital set-top box.
- This monitor supports HDCP (High-bandwidth Digital Contents Protection) protocol for DVI DTV (480p,720p,1080i) mode.
How to Connect
• Connect DTV set-top box video output to monitor COMPONENT (DVD/DTV INPUT) or to the monitor RGB1 (PC/DTV
INPUT), RGB2 (PC/DTV input) connector depending on your set-top box connectors.
• Connect DTV set-top box audio outputs to monitor AUDIO INPUT jacks.
How to View
1. Turn on the digital set-top box. (Refer to the digital set-top box owner’s manual.)
2. Use INPUT SELECT on the remote control to select COMPONENT, RGB 1, or RGB2.
PC Setup Overview
- To enjoy vivid picture and sound, connect a PC to the Monitor.
- Avoid keeping a fixed image on the monitor’s screen for a long period of time. The fixed image may become permanently
imprinted on the screen; use a screen saver when possible.
- There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC mode. If noise is present, change the PC mode to another resolution, change the refresh rate to another rate or adjust the brightness and
contrast on the menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the
PC graphic card or consult the manufacturer of the PC graphic card.
- The synchronization input form for Horizontal and Vertical frequencies is separate.
How to Connect a PC
- We recommend using 1024x768, 60Hz or 1366x768, 75Hz for the PC mode, they provide the best picture quality.
- Connect the signal cable from the monitor output port of the PC to the RGB1 INPUT (PC/DTV INPUT) port of the Monitor
or the signal cable from the DVI output port of the PC to the RGB2 INPUT (DIGITAL RGB INPUT) port on the Monitor and
change the resolution output of PC accordingly.
- Connect the audio cable from the PC to the Audio input on the Monitor. (Audio cables are not included with the Monitor).
- If using a sound card, adjust PC sound as required.
- This monitor provides a VESA Plug and Play capability. The monitor sends EDID data to the PC system with a DDC protocol. The PC adjusts automatically to use this monitor.
- DDC protocol is preset for RGB1 (Analog RGB), RGB2 (DVI, Digital RGB) mode.
- If required, adjust the monitor settings for Plug and Play functionally.
- If graphic card on the PC does not output analog and digital RGB simultaneously, connect only one of both RGB1 INPUT
(PC/DTV INPUT) or RGB2 INPUT (DIGITAL RGB INPUT) to display the PC on the monitor.
If graphic card on the PC does output analog and digital RGB simultaneously, set the monitor to either RGB1 or RGB2;
(the other mode is set to Plug and Play automatically by the monitor.)
- The monitor perceives 640x480, 60Hz as DTV 480p based on the PC graphic card. In this case, change the screen scanning rate for the graphic card.
How to View PC Image
1. Turn on the PC and the Monitor.
2. Turn on the display by pressing the POWER button on the Monitor’s remote control.
3. Use the INPUT SELECT button on the remote control to select the RGB1 or RGB2 input source.
4. Set the resolution output of the PC to WXGA or under (1366 x 768, 84.99Hz).
EXTERNAL CONTROL DEVICE SETUP
- Connect the RS-232C input jack to an external control device (such as a computer or an A/V control system)
and control the Monitor’s functions externally.
- Connect the serial port of the control device to the RS-232C jack on the Monitor back panel.
- RS-232C connection cables are not supplied with the Monitor.
Type of Connector: D-Sub 9-Pin male
No.
1
2
3
4
5
6
7
8
9
1
Pin name
No connection
RXD (Receive data)
TXD (Transmit data)
DTR (DTE side ready)
GND
DSR (DCE side ready)
RTS (Ready to send)
CTS (Clear to send)
No Connection
5
9
6
RS-232 Configurations
3-Wire Configuration
(Not standard)
7-Wire Configuration
(Standard RS-232C cable)
RXD
TXD
GND
DTR
DSR
RTS
CTS
PC
PDP
2
3
5
4
6
7
8
3
2
5
6
4
8
7
D-Sub 9
D-Sub 9
TXD
RXD
GND
DSR
DTR
CTS
RTS
RXD
TXD
GND
DTR
DSR
RTS
CTS
PC
PDP
2
3
5
4
6
7
8
3
2
5
4
6
7
8
D-Sub 9
D-Sub 9
TXD
RXD
GND
DTR
DSR
RTS
CTS
Control line
Set ID
- Use this function to specify a monitor ID number.
- Refer to ‘Real Data Mapping 1’. See page 25.
1. Press the MENU button and then use the
2. Press the
button and then use
D /E
3. Press the G button and then use
monitor ID number.
F /G
G
D /E
button to select the SPECIAL menu.
button to select SET ID.
VIDEO
AUDIO
TIME
button to adjust SET ID to choose the desired
SPECIAL
LANGUAGE
KEY LOCK
ORBITER
WHITE WASH
SET ID
OSD ROTATE
SCREEN
• The adjustment range of SET ID is 1 ~ 99.
TWIN
Communication Parameters
• Baud rate : 115200 bps (UART)
• Data length : 8 bits
• Parity : None
• Stop bit : 1 bit
• Communication code : ASCII code
MENU PREV.
G
1
EXTERNAL CONTROL DEVICE SETUP
OK Acknowledgement
Command Reference List
COMMAND 1 COMMAND 2
DATA
(Hexadecimal)
01. Power
02. Input Select
03. Aspect Ratio
04. Screen Mute
05. Volume Mute
06. Volume Control
07. Contrast
08. Brightness
09. Color
10. Tint
11. Sharpness
12. OSD select
13. Remote control lock mode
14. PIP/Twin
15. PIP size
16. PIP position
17. Treble
18. Bass
19. Balance
20. Color temperature
21. Red adjustment
22. Green adjustment
23. Blue adjustment
24. PIP input source
25. Orbiter
26. White Wash
27. Orbiter Time Setting
28. Orbiter Pixel Setting
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
j
j
j
j
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
q
r
s
t
u
v
w
$
y
p
q
r
s
0~1
0~4
0~2
0~1
0~1
0 ~ 64
0 ~ 64
0 ~ 64
0 ~ 64
0 ~ 64
0 ~ 64
0~1
0~1
0~3
0~1
0~3
0 ~ 64
0 ~ 64
0 ~ 64
0~3
0 ~ 64
0 ~ 64
0 ~ 64
0~4
0~1
0~1
1 ~ FE
0 ~9
• When setting the 25 ~ 28, a menu doesn’t display on
screen.
[Command2][ ][Set ID][ ][OK][Data][x]
• The Monitor transmits ACK (acknowledgement) based on
this format when receiving normal data. At this time, if the
data is data read mode, it indicates present status data. If
the data is data write mode, it returns the data of the PC
computer.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][x]
• The Monitor transmits ACK (acknowledgement) based on
this format when receiving abnormal data from
non-viable functions or communication errors.
01. Power (Command:a)
G To control Power On/Off of the Monitor.
Transmission
[k][a][ ][Set ID][ ][Data][Cr]
Data 0: Power Off
1: Power On
Acknowledgement
[a][ ][Set ID][ ][OK][Data][x]
Data 0: Power Off
1: Power On
G To show Power On/Off.
Transmission
[k][a][ ][Set ID][ ][FF][Cr]
Data 0: Power Off
1: Power On
Acknowledgement
[a][ ][Set ID][ ][OK][Data][x]
Data 0: Power Off
1: Power On
• In a like manner, if other functions transmit ‘FF’ data
based on this format, acknowledgement data feedback
presents status about each function.
Transmission / Receiving Protocol
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
• [Command 1]: k
• [Command 2]: To control PDP set.
• [Set ID]: You can adjust the set ID to choose desired moni-
•
•
•
tor ID number in special menu. See previous
page. Adjustment range is 1 ~ 99. When selecting
Set ID ‘0’, every connected PDP set is controlled.
[DATA]: To transmit command data.
Transmit ‘FF’ data to read status of command.
[Cr]: Carriage Return ASCII code ‘0x0D’
[ ]: ASCII code ‘space (0x20)’
02. Input Select (Command:b) (Main Picture Input)
G To select input source for the Monitor.
You can also select an input source using the INPUT
SELECT button on the Monitor's remote control.
Transmission
[k][b][ ][Set ID][ ][Data][Cr]
Data 0: RGB 1
1: COMPONENT
2: VIDEO
3: S-VIDEO
4: RGB 2
Acknowledgement
[b][ ][Set ID][ ][OK][Data][x]
Data 0: RGB 1
1: COMPONENT
2: VIDEO
3: S-VIDEO
4: RGB 2
EXTERNAL CONTROL DEVICE SETUP
03. Aspect Ratio (Command:c) (Main picture format)
07. Contrast (Command:g)
G To adjust the screen format.
You can also adjust the screen format using the ARC
(Aspect Ratio Control) button on remote control or in the
Special menu.
Transmission
G To adjust screen contrast.
You can also adjust contrast in the Video menu.
[k][c][ ][Set ID][ ][Data][Cr]
Data 0: Wide screen (16:9)
1: Normal screen (4:3)
2: Full screen (Zoom)
Acknowledgement
[c][ ][Set ID][ ][OK][Data][x]
Data 0: Wide screen (16:9)
1: Normal screen (4:3)
2: Full screen (Zoom)
• Using the PC input, select either 16:9 or 4:3 screen aspect
ratio.
04. Screen Mute (Command:d)
G To select screen mute on/off.
Transmission
[k][d][ ][Set ID][ ][Data][Cr]
Data 0: Screen mute off (Picture on)
1: Screen mute on (Picture off)
Acknowledgement
[d][ ][Set ID][ ][OK][Data][x]
Data 0: Screen mute off (Picture on)
1: Screen mute on (Picture off)
05. Volume Mute (Command:e)
G To control volume mute on/off.
You can also adjust mute using the MUTE button on
remote control.
Transmission
[k][e][ ][Set ID][ ][Data][Cr]
Data 0: Volume mute on (Volume off)
1: Volume mute off (Volume on)
Acknowledgement
[e][ ][Set ID][ ][OK][Data][x]
Transmission
[k][g][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64
• Refer to ‘Real data mapping1’ as shown below.
Acknowledgement
[g][ ][Set ID][ ][OK][Data][x]
Data Min: 0 ~ Max: 64
08. Brightness (Command:h)
G To adjust screen brightness.
You can also adjust brightness in the Video menu.
Transmission
[k][h][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64
• Refer to ‘Real data mapping1’ as shown below.
Acknowledgement
[h][ ][Set ID][ ][OK][Data][x]
Data Min: 0 ~ Max: 64
09. Color (Command:i)
G To adjust the screen color.
You can also adjust color in the Video menu.
Transmission
[k][i][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64
• Refer to ‘Real data mapping1’ as shown below.
Acknowledgement
[i][ ][Set ID][ ][OK][Data][x]
Data Min: 0 ~ Max: 64
10. Tint (Command:j)
G To adjust the screen tint.
You can also adjust tint in the Video menu.
Transmission
[k][j][ ][Set ID][ ][Data][Cr]
Data 0: Volume mute on (Volume off)
1: Volume mute off (Volume on)
Data Red: 0 ~ Green: 64
• Refer to ‘Real data mapping1’ as shown below.
Acknowledgement
06. Volume Control (Command:f)
[j][ ][Set ID][ ][OK][Data][x]
G To adjust volume.
You can also adjust volume with the volume buttons
on remote control.
Transmission
Data Red: 0 ~ Green: 64
•
Real data mapping 1
0 : Step 0
[k][f][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64
• Refer to ‘Real data mapping1’ as shown right.
Acknowledgement
A : Step 10 (SET ID 10)
F : Step 15 (SET ID 15)
10 : Step 16 (SET ID 16)
[f][ ][Set ID][ ][OK][Data][x]
Data Min: 0 ~ Max: 64
•
Real data mapping 2
0 : -10
5 : -9
A : -8
2D: -1
32: 0
37: +1
64 : Step 100
5F: +9
64: +10
EXTERNAL CONTROL DEVICE SETUP
Acknowledgement
11. Sharpness (Command:k)
[o][ ][Set ID][ ][OK][Data][x]
G To adjust the screen sharpness.
You can also adjust sharpness in the Video menu.
Data 0 : 4:3
Transmission
[k][k][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64
• Refer to ‘Real data mapping1’. See page 25.
Acknowledgement
[k][ ][Set ID][ ][OK][Data][x]
16. PIP Position (Command:q)
G To select sub picture position for PIP.
You can also adjust the sub picture position using
WIN.POSITION on the remote control or in the Special menu.
Transmission
[k][q][ ][Set ID][ ][Data][Cr]
12. OSD Select (Command:l)
Data 0:
1:
2:
3:
G To select OSD (On Screen Display) on/off.
Acknowledgement
Data Min: 0 ~ Max: 64
Right down on screen
Left down on screen
Left up on screen
Right up on screen
Transmission
[q][ ][Set ID][ ][OK][Data][x]
[k][l][ ][Set ID][ ][Data][Cr]
Data 0:
1:
2:
3:
Data 0: OSD off
1: OSD on
Acknowledgement
1: 16:9
Right down on screen
Left down on screen
Left up on screen
Right up on screen
[l][ ][Set ID][ ][OK][Data][x]
Data 0: OSD off
1: OSD on
13. Remote Control Lock Mode (Command:m)
17. Treble (Command:r)
G To adjust treble.
You can also adjust treble in the Audio menu.
G To lock the front panel controls on the monitor
Transmission
Transmission
[k][r][ ][Set ID][ ][Data][Cr]
[k][m][ ][Set ID][ ][Data][Cr]
Data 0: Lock off
1: Lock on
Acknowledgement
[r][ ][Set ID][ ][OK][Data][x]
[m][ ][Set ID][ ][OK][Data][x]
Data 0: Lock off
1: Lock on
• If you’re not using the remote control, use this mode.
When main power is on/off, remote control lock is released.
14. PIP / Twin (Command:n)
G To control the PIP (Picture In picture).
You can also control the PIP/TWIN using the PIP or Twin
picture button on the remote control or in the Special menu.
Transmission
[k][n][ ][Set ID][ ][Data][Cr]
Data 0: PIP/DW of
1: PIP
Data Min: 0 ~ Max: 64
• Refer to ‘Real data mapping1’. See page 25.
Acknowledgement
2: DW1
3: DW2
Data Min: 0 ~ Max: 64
18. Bass (Command:s)
G To adjust bass.
You can also adjust bass in the Audio menu.
Transmission
[k][s][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64
• Refer to ‘Real data mapping1’. See page 25.
Acknowledgement
[s][ ][Set ID][ ][OK][Data][x]
Data Min: 0 ~ Max: 64
Acknowledgement
19. Balance (Command:t)
[n][ ][Set ID][ ][OK][Data][x]
Data 0: PIP/DW of
1: PIP
2: DW1
3: DW2
15. PIP Size (Command:o)
G To select the PIP picture format.
You can also select the PIP picture format using WIN.SIZE
on the remote control.
Transmission
[k][o][ ][Set ID][ ][Data][Cr]
Data 0: 4:3
1: 16:9
G To adjust balance.
You can also adjust balance in the Audio menu.
Transmission
[k][t][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64
• Refer to ‘Real data mapping1’. See page 25.
Acknowledgement
[t][ ][Set ID][ ][OK][Data][x]
Data Min: 0 ~ Max: 64
EXTERNAL CONTROL DEVICE SETUP
20. Color Temperature (Command:u)
25. Orbiter (Command:p)
G To adjust color temperature.
You can also adjust ACC in the Video menu.
G To control the orbiter function on/off.
Transmission
Transmission
[j][p][ ][Set ID][ ][Data][Cr]
[k][u][ ][Set ID][ ][Data][Cr]
Data 0: Normal
1: Cool
2: Warm
3: User
Data 0: Orbiter off
1: Orbiter on
Acknowledgement
2: Warm
3: User
Data 0: Orbiter off
1: Orbiter on
Acknowledgement
[u][ ][Set ID][ ][OK][Data][x]
Data 0: Normal
1: Cool
[p][ ][Set ID][ ][OK][Data][x]
21. Red Adjustment (Command:v)
G To adjust red in color temperature.
26. White Wash (Command:q)
Transmission
G To control the white wash function on/off.
[k][v][ ][Set ID][ ][Data][Cr]
Transmission
Data Min: 0 ~ Max: 64
• Refer to ‘Real data mapping 2’. See page 25.
Acknowledgement
[j][q][ ][Set ID][ ][Data][Cr]
[v][ ][Set ID][ ][OK][Data][x]
Data 0: White Wash off
1: White Wash on
Acknowledgement
Data Min: 0 ~ Max: 64
[q][ ][Set ID][ ][OK][Data][x]
22. Green Adjustment (Command:w)
Data 0: White Wash off
1: White Wash on
G To adjust green in color temperature.
Transmission
[k][w][ ][Set ID][ ][Data][Cr]
27. Orbiter Time Setting (Command:r)
Data Min: 0 ~ Max: 64
• Refer to ‘Real data mapping 2’. See page 25.
Acknowledgement
G To adjust orbiter operation time term.
Transmission
[j][r][ ][Set ID][ ][Data][Cr]
[w][ ][Set ID][ ][OK][Data][x]
23. Blue Adjustment (Command:$)
Data Min: 1 ~ Max: FE
• Refer to ‘Real data mapping1’. See page 25.
Acknowledgement
G To adjust blue in color temperature.
[r][ ][Set ID][ ][OK][Data][x]
Transmission
Data Min: 1 ~ Max: FE
Data Min: 0 ~ Max: 64
[k][$][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64
• Refer to ‘Real data mapping 2’. See page 25.
Acknowledgement
28. Orbiter Pixel Setting (Command:s)
[$][ ][Set ID][ ][OK][Data][x]
G To adjust pixel number in orbiter function.
Data Min: 0 ~ Max: 64
Transmission
24. PIP Input Select (Command:y)
[j][s][ ][Set ID][ ][Data][Cr]
G To select input source for sub picture in PIP mode.
Data Min: 0 ~ Max: 9
• Refer to ‘Real data mapping1’. See page 25.
Acknowledgement
Transmission
[k][y][ ][Set ID][ ][Data][Cr]
Data 0: RGB1
2: VIDEO
1: COMPONENT
3: S-VIDEO
[s][ ][Set ID][ ][OK][Data][x]
4: RGB2
Acknowledgement
[y][ ][Set ID][ ][OK][Data][x]
Data 0: RGB1
2: VIDEO
1: COMPONENT
3: S-VIDEO
4: RGB2
Data Min: 0 ~ Max: 9
IR CODE(NEC Format)
How to Connect
G Connect your wired remote control to the Remote port on the Monitor.
Set the CONTROL LOCK to ‘ON’ on the Monitor back panel to operate Monitor with wired remote control.
Remote Control IR Code (NEC Format)
G Output waveform
Single pulse, modulated with 37.917KHz signal at 455KHz
TC
Carrier frequency
FCAR = 1/TC = fOSC/12
Duty ratio = T1/TC = 1/3
T1
G Configuration of frame
• 1st frame
Lead
code
Low
custom code
High
custom code
Data code
Data code
C0 C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7
• Repeat frame
Repeat code
Tf
G Lead code
9 ms
4.5 ms
0.55 ms
G Repeat code
9 ms
2.25 ms
G Bit description
• Bit “0”
• Bit “1”
0.56 ms
0.56 ms
1.12 ms
2.24 ms
G Frame interval : Tf
The waveform is transmitted as long as a key is depressed.
Tf
Tf
Tf=108ms @455KHz
ADJUSTMENT INSTRUCTIONS
1. Application Object
4. MAX Bias Adjustment
These instructions are applied to all of the PDP monitor, RF02CA.
(1) Input Full White (255 Gray) signal which generated from
Pattern Generator into CVBS and RGB1 Input part.
(2) Press POWER ON KEY on R/C for adjustment and select
MAX-BIAS
(3) Press Vol. + key and operate TO SET
(4) Original Full White screen will be presented about 1~2
seconds later.
(5) After adjustment, press key to save adjustment and
come out of the adjustment mode.
2. Notes
(1) Because this is not a hot chassis, it is not necessary to use
an isolation transformer. However, the use of isolation
transformer will help protect test instrument.
(2) Adjustment must be done in the correct order.
(3) The adjustment must be performed in the circumstance of
25±5°C of temperature and 65±10% of relative humidity.
(4) The input voltage of the receiver must keep 110~240V,
50/60Hz in adjusting.
(5) The receiver must be operated for about 15 minutes prior
to the adjustment.
O
1) After receiving 100% white pattern (06CH), the receiver
must be operate prior to adjustment. (Or white condition
in HEAT-RUN mode)
2) Enter into HEAT-RUN mode
- Press the POWER ON KEY on R/C for adjustment.
- OSD display HEAT-RUN WHITE and screen display
100% full WHITE PATTERN.
[ Set is activated HEAT-RUN without signal generator in
this mode.
[ Single color pattern of HEAT-RUN mode uses to check
PANEL. (RED/BLUE/GREEN)
You can check whether circuit adjustment is operated well or
not, as below.
(1) Display RGB1 to the Main picture, CVBS to the Sub
picture in the TWIN PICTURE.
(2) To check the MIN-Bias, input Full Black (0 gray) signal into
CVBS and RGB1 input part at the same time in the Pattern
Generator.
(3) To check the MAX-Bias, input Full White (255 gray) signal
into CVBS and RGB1 input part at the same time in the
Pattern Generator.
(4) Compare Black Level with White Level by eyes. And if
there is no Level difference, the adjustment is completed
well.
Data value, which adjusted in the board, is valid until the VSC
Board is dissued and must be protected. For the protection of
data, Micom does not permit any more adjustment after
completion.
O In case of re-adjustment, operate First Value Setting.
O
[Caution] If you turn on a still screen more than 20 minutes
(such as Cross Hatch Pattern), a afterimage may be
occur in the black level part of the screen.
3. RGB Auto Cut-Off & MIN Bias
Adjustment
(1) Input Full Back (0 Gray) signal which generated from
Pattern Generator into CVBS and RGB1 Input part.
(2) Press POWER ON KEY on R/C for adjustment and select
AUTO-CUT(Cut-off Auto Adjustment)
(3) Press Vol. + key and operate TO SET
(4) Screen adjustment starts with Full Black screen.
Original Window screen will be presented about 5-6
seconds later. And if there is a mark of OK OSD, then the
Auto Cut-off and Min-Bias adjustment will be completed.
(5) Pass to the next MAX Bias Adjustment after Adjustment.
[ Once the module is replaced the voltage must be adjusted.
Each PCB Assy must be checked by Check JIG Set before
assembly. (Especially, be careful Power PCB Assy which can
cause fatal Damage to PDP Module.)
5. POWER PCB Assy Voltage
Adjustment (Va, Vs Voltage Adjustment)
5-1 Test Equipment : D.M.M 1EA
5-2 Connection Diagram for Measuring
Refer to Fig 1.
5-3 Adjustment Method
(1) Va Adjustment
1) After receiving 100% white pattern, HEAT RUN.
2) Connect + terminal of D.M.M to Va pin of P805 and
connect – terminal to GND pin of P805.
3) After turning the VR4, voltage of D.M.M adjustment as
same as Va voltage which on label of panel Right/Top.
(Deviation : ±0.5V)
ADJUSTMENT INSTRUCTIONS
(2) Vs adjustment
1) Connect + terminal of D.M.M to Vs pin of P805 and
connect – terminal to GND pin of P805.
2) Adjust VR1 until DVM reads the same as the voltage labled
on the PWB. (Deviation : ±0.5V)
Va voltage
adjustment
variable resistor
Vs voltage
adjustment
variable resistor
R-L 70
G-L 70
R-M 128
G-M 128
R-H 216
G-H 216
COLOR
ANALYZER
TYPE;CA-100
Middle Light
128 Gray Level
70~75Cd/
RGB Signal Input
PDP MONITOR
P806
P805
Window
VR4
GND
GND
Va
NC
Vs
Vs
MSPG-2100 or
MSTG-5200
DMM
VR1
<Fig 3> Connection Diagram of Manual Adjustment (Middle Light)
R-L 70
G-L 70
R-M 128
G-M 128
R-H 216
G-H 216
COLOR
ANALYZER
TYPE;CA-100
Low Light
70 Gray Level
20~25Cd/
RGB Signal Input
PDP MONITOR
Window
MSPG-2100 or
MSTG-5200
<Fig 1> Connection Diagram of Power Adjustment for Measuring
<Fig 4> Connection Diagram of Manual Adjustment (Low Light)
6. Adjustment of White Balance
6-1. Required Equipment
6-2. Connection Diagram of Equipment for
Measuring (Manual Adjustment)
COLOR
ANALYZER
TYPE;CA-100
High Light
216 Gray Level
135~140Cd/
O
O
Color analyzer (CA-100 or same product)
R-L 70
G-L 70
R-M 128
G-M 128
R-H 216
G-H 216
6-3. Adjustment of White Balance
RGB Signal Input
PDP MONITOR
Window
MSPG-2100 or
MSTG-5200
<Fig 2> Connection Diagram of Manual Adjustment (High Light)
Operate the Zero-calibration of the CA-100, then stick sensor
to PDP module surface when you adjust.
For manual adjustment, it is also possible by the following
sequence.
(1) Select WHITE PATTERN of HEAT RUN mode by pressing
POWER ON KEY on SVC remote control for adjustment then
operate HEAT RUN more than 15 minute.
(2) Supply 216Gray, 128Gray, 70Gray Level, 50% size length
and breadth signal to RGB1 input. (Refer to Fig 2,3,4)
(3) W/B adjustment must be adjusted once and follow the
sequence of Low Light --> Middle Light --> High Light and
then save the adjustment value with o Key.
(4) To adjust Low Light , stick sensor to Gray Level(or 20~25
Cd/m2) Pattern, press ADJ Key on R/C for adjustment and
press v, x on R/C in adjustment mode to select R-L or G-L,
press VOL +, - Key and adjust it until color coordination
becomes as below.
X: 0.290±0.003, Y: 0.300±0.003,
Color temperature: 8, 500°K±500°K
(5) To adjust Middle Light , stick sensor to Gray Level(or 70~75
Cd/m2) Pattern, press ADJ Key on R/C for adjustment and
ADJUSTMENT INSTRUCTIONS
press v, x on R/C in adjustment mode to select R-M or G-M,
press VOL +, - Key and adjust it until color coordination
becomes as below.
X: 0.290±0.003, Y: 0.300±0.003
Color temperature: 8, 500°K±500°K
(6) To adjust High Light, stick sensor to Gray Level (or 135-140
Cd/m2) Pattern, press ADJ Key on R/C for adjustment and
press v, x on R/C in adjustment mode to select R-L or G-L,
press VOL +, - Key and adjust it until color coordination
becomes as below.
X: 0.290±0.003, Y: 0.300±0.003
Color temperature: 8, 500°K±500°K
(2) DDC Data input for Digital-RGB
1) Connect PC Serial to DVI Cable of JIG for DDC
Adjustment to RGB2 terminal (DVI Jack).
2) Operate S/W for DDC record and select DDC Data for
Digital RGB in Model Menu.
3) Operate EDID Write command.
4) Operate EDID Read command and check whether
Check Sum is OK.
5) If Check Sum is NG, repeat 3) ~ 4).
6) If Check Sum is OK, DDC Data for Digital-RGB input is
completed.
(7) Exit adjustment mode using o Key.
8. Component Off-Set adjustment
7. DDC Data Input
7-1. Required Test Equipment
(1) A jig for adjusting PC, DDC. (PC serial to D-sub.
Connection equipment)
(2) S/W for writing DDC(EDID data write & read)
(3) D-Sub 15P cable, D-Sub to DVI Connector (Connect to
DVI Jack)
7-2. Setting of Device
7-3. Preparation for Adjustment
(1) Set devices as above and turn the PC, jig on.
(2) Put S/W for writing DDC (EDID data write & read) into
operation. (operated in DOS mode.)
7-4. Sequence of Adjustment
(1) DDC Data Input for Analog-RGB
1) Put the set on the table and turn the power on.
2) Connect PC Serial to D-sub 15P Cable of JIG for DDC
Adjustment to RGB1 terminal (D-Sub 15Pin).
3) Operate S/W for DDC record and select DDC Data for
Analog RGB in Model Menu.
4) Operate EDID Write command.
5) Operate EDID Read command and check whether
Check Sum is OK.
6) If Check Sum is NG, repeat 3) ~ 4).
7) If Check Sum is OK, DDC Data for Analog-RGB input is
completed.
Input the signal to HD-STB (SK-010T) and receive 14Ch.
8-1. Required Equipment
HD-STB (SK-010T or same product)
8-2. Manual Adjustment of Off-Set
(1) Input Video signal and Component 720P, 1080i signal of
HD-STB into AV1 and Component input.
(2) Select Twin Picture by pressing the adjust key twice,
check component in the main picture and AV1 in the sub
picture.
(3) Adjust the R-OFFSET, B-OFFSET color impression of
component (Main picture) and external Input (Sub picture)
same by pressing Volume +,- key.
BLOCK DIAGRAM
NOTES
EXPLODED VIEW
300
305
301
303
200
207
209
202
211
201
302
204
203
206
212
213
208
210
205
215
214
610
520
550
580
581
101
400
570
560
530
410
401
590
591
540
310
320
330
EXPLODED VIEW PARTS LIST
No.
Part No.
Description
101
5900V12001A
FAN,DC G1225S12B2
200
6348Q-C030C
PDP,50 16:9 1365*768 DUAL SCAN POWER, INTERCOMPANY MODEL
201
6871QCH019A
PCB ASSEMBLY,CTRL ASSY 50INCH VER4 ASIC 370*220
202
6871QDH030A
PCB ASSEMBLY,YDRV ASSY 50WX1 4 LAYER(TOP)
203
6871QDH031A
PCB ASSEMBLY,YDRV ASSY 50WX1 4 LAYER(BOTTOM)
204
6871QLH018A
PCB ASSEMBLY,XRLT ASSY 50WX1 4LAYER LEFT TOP
205
6871QLH019A
PCB ASSEMBLY,XRLT ASSY 50WX1 4LAYER LEFT BOTTOM
206
6871QPH006A
PCB ASSEMBLY,MAIN DCDC ASSY 50WX1
207
6871QRH016A
PCB ASSEMBLY,XRRT ASSY 50WX1 4LAYER RIGHT TOP
208
6871QRH017A
PCB ASSEMBLY,XRRT ASSY 50WX1 4LAYER RIGHT BOTTOM
209
6871QXH011A
PCB ASSEMBLY,XRCT ASSY 50WX1 4LAYER CENTER TOP
210
6871QXH012A
PCB ASSEMBLY,XRCT ASSY 50WX1 4LAYER CENTER BOTTOM
211
6871QYH020B
PCB ASSEMBLY,YSUS ASSY 50WXDP1 NEWASIC 4 LAYER
212
6871QZH021A
PCB ASSEMBLY,ZSUS ASSY 50WX1 2 LAYER
213
4980V00416A
SUPPORTER ASSY,NON MN-50PZ40 RIGHT
214
4980V00416B
SUPPORTER ASSY,NON MN-50PZ40 LEFT
215
4980V00498B
SUPPORTER ASSY,AL SMPS DELTA
300
3091V00433E
CABINET ASSEMBLY,MU-50PZ41S STEREO RF02CA
301
4980V00361A
SUPPORTER,FILTER EGI MN-50PZ40
302
4980V00362A
SUPPORTER,FILTER EGI MN-50PZ40
303
4980V00363A
SUPPORTER,FILTER EGI MN-50PZ40
305
3790V00683A
WINDOW,GLASS FILTER MN50PZ41 MESH 1107*623 NBK
310
5020V00688A
BUTTON,CONTROL MN-50PZ41 . SET
320
320-062H
330
5020V00645A
BUTTON,POWER OUTER MN-50PZ40 SET
400
3809V00292A
BACK COVER ASSEMBLY,MN-50PZ40 NON NON
401
3301V00009D
PLATE ASSEMBLY,AV MU-50PZ41
410
3809V00293B
BACK COVER ASSEMBLY,MN-50PZ41 NON NON
520
6871VMMN95A
PCB ASSEMBLY,MAIN RF-02KE FOR MU PIVOT MODEL
530
6871VSMD10A
PCB ASSEMBLY,SUB EXTRA RF-02CA 50IN IF/FIX
540
6871VSMD04A
PCB ASSEMBLY,SUB INTER RF-02CA I/F NTSC
550
6871VSMD06C
PCB ASSEMBLY,SUB A/V RF02CA 50IN AUDIO
560
6871VSMD11C
PCB ASSEMBLY,SUB SPK RF02CA 50IN RIGHT SPK
561
4980V00384A
SUPPORTER,SPK AL INTERFACE,MN-50PZ40
570
3141VSNA57A
CHASSIS ASSEMBLY,SUB NON RF-02CA PRE AMP
580
6871VSMD08A
PCB ASSEMBLY,SUB KBD RF-02CA 50IN LOCAL KEY
581
5020V00647A
BUTTON,CONTROL S/W INNER MN-50PZ40 SET
590
6871VSMD09A
PCB ASSEMBLY,SUB PSW RF-02CA 50IN POWER SWITCH
591
5020V00648A
BUTTON,POWER INNER MN-50PZ40 SET
600
6871VSMN17A
PCB ASSEMBLY,SUB EXTRA RF02CA RF-02CA FAN CONTROL BOARD
610
3501V00084C
BOARD ASSEMBLY,POWER BOARD MU50PZ41 RF02KA SONY CSA950
SPRING,COIL
REPLACEMENT PARTS LIST
For Capacitor & Resistors, the
charactors at 2nd and 3rd digit
in the P/No. means as follows;
LOCA. NO
CC, CX, CK, CN : Ceramic
CQ : Polyestor
CE : Electrolytic
PART NO
RD : Carbon Film
RS : Metal Oxide Film
RN : Metal Film
RF : Fusible
DESCRIPTION
IC
IC1
0IMI623200B
M62320FP,I/O EXPANDER 16P
IC101
0IMCRMN002A
IC101
0ISO208900A
CXA2089Q 48QFP BK A/V SWITCH
IC101
0IAL242110A
AT24C2110SI2.5 8P,SOP TP 1K EEPROM
IC102
0IKE780800J
KIA7808API 3 ST REGULATOR .
IC102
0IAL242110A
AT24C2110SI2.5 8P,SOP TP 1K EEPROM
IC103
0ISH052100C
PQ05RD21 4SIP ST REGULATOR
IC103
0IMCRTI003A
SN74HCT08D TEXAS INSTRUMENT 16P
IC104
0IKE704200J
KIA7042AF SOT89 TP 4.2V
IC104
0IBB368200A
OPA3682E 16P SOP ST BUFFER AMP
MSP3440G QA B6 MICRONAS 80
0IDS162100B
DS1621V 8P SOIC ST THERMOSTAT
IC201
0IMCRAD003A
AD9888KS140 ANALOG DEVICE 128P
IC202
0IMCRS5003A
SIL169 CL100 SILICON IMAGE 100P
IC203
0IMCRTI001A
SN74HCT157D TEXAS INSTRUMENT 16P
IC3
0ISS278050A
KA278R05 4P,TO220F BK LOW DROP 5V
IC2
RUN DATE : 2002.12.3
LOCA. NO
PART NO
DESCRIPTION
IC802
0ISA428200A
LA4282 12S 2CHX10W AUDIO AMP
IC802
0IPRPML001A
MIC39100 3P SOT223 R/TP LDO TYPE 2.5V
IC803
0IMCRFA010A
KA7809R, FAIRCHILD 2P DPAK
IC850
0IMCRRH001A
BA033FP ROHM 3PSOP
IC851
0IMCRRH001A
BA033FP ROHM 3PSOP
IC852
0IMCRRH001A
BA033FP ROHM 3PSOP
IC853
0IMCRRH001A
BA033FP ROHM 3PSOP
IC854
0IMCRRH001A
BA033FP ROHM 3PSOP
IC858
0IMCRRH001A
BA033FP ROHM 3PSOP
ICN102
0IMCRFA010A
KA7809R, FAIRCHILD 2P DPAK
TRANSISTOR
IC105
0TR830009BA
BSS83 TP PHILIPS NON NCHANNEL S/W TR
IC106
0TR830009BA
BSS83 TP PHILIPS NON NCHANNEL S/W TR
IC7
0TR830009BA
BSS83 TP PHILIPS NON NCHANNEL S/W TR
IC8
0TR830009BA
BSS83 TP PHILIPS NON NCHANNEL S/W TR
Q001
0TR387500AA
CHIP 2SC3875S(ALY) KEC
Q002
0TR387500AA
CHIP 2SC3875S(ALY) KEC
Q104
0TR387500AA
CHIP 2SC3875S(ALY) KEC
Q150
0TR387500AA
CHIP 2SC3875S(ALY) KEC
Q151
0TR387500AA
CHIP 2SC3875S(ALY) KEC
IC301
0IMMRNE002A
IC302
0ISA715100D
LA7151M 10SOP R/TP AUDIO SW
IC4
0ISH092100A
PQ09RF21 4P 9V S/W REGULATOR
IC401
0IIT323000D
VPC3230D QA B4 80P QFP TRAY SOUND
IC402
0IFA741230A
DM74LS123MX 16SOP TP DUAL RETRIG. MONO
Q152
0TR387500AA
CHIP 2SC3875S(ALY) KEC
IC403
0IKE702700D
KIA7027AF 3, SOT89 TP RESET IC 2.7V
Q153
0TR387500AA
CHIP 2SC3875S(ALY) KEC
IC404
0IMCRG2001A
FLI2200 SAGE 176P,QFP TRAY VIDEO
Q155
0TR387500AA
CHIP 2SC3875S(ALY) KEC
IC405
0ISS464323A
K4S643232E(C)TC/L60(70) (KM432S2030CT/G)
Q156
0TR387500AA
CHIP 2SC3875S(ALY) KEC
IC5
0ISH092100A
PQ09RF21 4P 9V S/W REGULATOR
Q157
0TR387500AA
CHIP 2SC3875S(ALY) KEC
UPD64083GF3BA NEC 100 QFP ST 3D
IC501
0IMCROT001A
REMBRANT1A OPLUS TECHNOLOGIES LTD
Q158
0TR387500AA
CHIP 2SC3875S(ALY) KEC
IC502
0ISS464323A
K4S643232E(C)TC/L60(70) (KM432S2030CT/G)
Q161
0TR150400BA
CHIP 2SA1504S(ASY) KEC
IC503
0ISS464323A
K4S643232E(C)TC/L60(70) (KM432S2030CT/G)
Q162
0TR150400BA
CHIP 2SA1504S(ASY) KEC
IC504
0ISS464323A
K4S643232E(C)TC/L60(70) (KM432S2030CT/G)
Q300
0TR150400BA
CHIP 2SA1504S(ASY) KEC
IC6
0ISS278120A
KA278R12 4P,TO220F BK LOW DROP 12V
Q301
0TR150400BA
CHIP 2SA1504S(ASY) KEC
IC601
0IS5160000A
SII160 100 TQFP ST PANELLINK DIGITAL
Q302
0TR387500AA
CHIP 2SC3875S(ALY) KEC
IC701
0IMCRRS001A
R8820LV RDC SEMICONDUCTOR LTD 100P
Q303
0TR150400BA
CHIP 2SA1504S(ASY) KEC
IC702
0IMMRSS064A
K6R4016V1DTC10 44P
Q304
0TR150400BA
CHIP 2SA1504S(ASY) KEC
IC703
0IMMRMR006A
COPY MX29LV160TTC70 MACRONIX 48P
Q305
0TR150400BA
CHIP 2SA1504S(ASY) KEC
IC704
0IAL241610A
AT24C16N10SI 8P SOIC ST EEPROM
Q306
0TR387500AA
CHIP 2SC3875S(ALY) KEC
IC741
0IMCRFA013A
74LCX244MTC FAIRCHILD 20P TSSOP
Q307
0TR150400BA
CHIP 2SA1504S(ASY) KEC
IC742
0IMCRFA013A
74LCX244MTC FAIRCHILD 20P TSSOP
Q308
0TR387500AA
CHIP 2SC3875S(ALY) KEC
IC743
0ITI745740M
SN74HC574NSR 14P,SOP TP DTYPE
Q309
0TR387500AA
CHIP 2SC3875S(ALY) KEC
IC744
0IMCRPH017A
74LVC574APW PHILIPS 20P SOT3601
Q310
0TR150400BA
CHIP 2SA1504S(ASY) KEC
IC745
0IPH740800L
74LVT08D 14SOP R/TP LOW VOLTAGE
Q314
0TR387500AA
CHIP 2SC3875S(ALY) KEC
IC746
0IMCRPH015A
74LVC32AD PHILIPS 14P SOT1081
Q315
0TR387500AA
CHIP 2SC3875S(ALY) KEC
IC747
0IMCRPH016A
74LVC139D PHILIPS 16P SOT1091
Q316
0TR150400BA
CHIP 2SA1504S(ASY) KEC
IC748
0IMCRPH014A
74LV132D PHILIPS 14P SOT1081
Q317
0TR387500AA
CHIP 2SC3875S(ALY) KEC
IC749
0IKE702700D
KIA7027AF 3, SOT89 TP RESET IC 2.7V
Q318
0TR150400BA
CHIP 2SA1504S(ASY) KEC
IC750
0IDS232000A
DS232AS 16P,SOP TP RS232
Q319
0TR387500AA
CHIP 2SC3875S(ALY) KEC
IC752
0IMCRTI001A
SN74HCT157D 16P R/TP RLJA10
Q320
0TR387500AA
CHIP 2SC3875S(ALY) KEC
IC801
0IMCRSJ001A
SC1565IST1.8 3P SOT223 TP REGULATOR
Q400
0TR387500AA
CHIP 2SC3875S(ALY) KEC
REPLACEMENT PARTS LIST
LOCA. NO
PART NO
DESCRIPTION
LOCA. NO
PART NO
DESCRIPTION
Q401
0TR387500AA
CHIP 2SC3875S(ALY) KEC
D123
0DD226239AA
CHIP KDS226 SOT23
Q402
0TR387500AA
CHIP 2SC3875S(ALY) KEC
D801
0DD226239AA
CHIP KDS226 SOT23
Q403
0TR150400BA
CHIP 2SA1504S(ASY) KEC
D802
0DD226239AA
CHIP KDS226 SOT23
Q404
0TR387500AA
CHIP 2SC3875S(ALY) KEC
D803
0DD226239AA
CHIP KDS226 SOT23
Q405
0TR104009AF
CHIP KRC104S SOT23 TP KEC
D850
0DD226239AA
CHIP KDS226 SOT23
Q406
0TR150400BA
CHIP 2SA1504S(ASY) KEC
D851
0DD226239AA
CHIP KDS226 SOT23
Q407
0TR150400BA
CHIP 2SA1504S(ASY) KEC
D852
0DD226239AA
CHIP KDS226 SOT23
QA101
0TR150400BA
CHIP 2SA1504S(ASY) KEC
D853
0DD226239AA
CHIP KDS226 SOT23
QA102
0TR150400BA
CHIP 2SA1504S(ASY) KEC
D854
0DD226239AA
CHIP KDS226 SOT23
QA103
0TR150400BA
CHIP 2SA1504S(ASY) KEC
D855
0DD226239AA
CHIP KDS226 SOT23
QA720
0TR387500AA
CHIP 2SC3875S(ALY) KEC
D857
0DD226239AA
CHIP KDS226 SOT23
QA721
0TR387500AA
CHIP 2SC3875S(ALY) KEC
D859
0DD226239AA
CHIP KDS226 SOT23
QA722
0TR387500AA
CHIP 2SC3875S(ALY) KEC
DA101
0DD184009AA
KDS184S CHIP 85V 300MA KEC TP
QA723
0TR150400BA
CHIP 2SA1504S(ASY) KEC
DA102
0DD184009AA
KDS184S CHIP 85V 300MA KEC TP
QA740
0TR387500AA
CHIP 2SC3875S(ALY) KEC
DA103
0DD184009AA
KDS184S CHIP 85V 300MA KEC TP
QN101
0TR387500AA
CHIP 2SC3875S(ALY) KEC
DA104
0DD184009AA
KDS184S CHIP 85V 300MA KEC TP
QN102
0TR387500AA
CHIP 2SC3875S(ALY) KEC
DA105
0DD226239AA
CHIP KDS226 SOT23
QN103
0TR387500AA
CHIP 2SC3875S(ALY) KEC
DA106
0DD226239AA
CHIP KDS226 SOT23
QN104
0TR387500AA
CHIP 2SC3875S(ALY) KEC
DN101
0DD226239AA
CHIP KDS226 SOT23
QN104
0TR150400BA
CHIP 2SA1504S(ASY) KEC
DN102
0DD226239AA
CHIP KDS226 SOT23
QN105
0TR387500AA
CHIP 2SC3875S(ALY) KEC
DN105
0DD226239AA
CHIP KDS226 SOT23
QN105
0TR150400BA
CHIP 2SA1504S(ASY) KEC
DN111
0DD226239AA
CHIP KDS226 SOT23
QN106
0TR387500AA
CHIP 2SC3875S(ALY) KEC
LD300
0DL233309AC
LED,SAM2333 TP KWANG GREEN/RED
QN107
0TR150400BA
CHIP 2SA1504S(ASY) KEC
LD460
0DL233309AC
LED,SAM2333 TP KWANG GREEN/RED
QN108
0TR387500AA
CHIP 2SC3875S(ALY) KEC
LD461
0DL233309AC
LED,SAM2333 TP KWANG GREEN/RED
LD740
0DL233309AC
LED,SAM2333 TP KWANG GREEN/RED
LD741
0DL233309AC
LED,SAM2333 TP KWANG GREEN/RED
DIODE
D001
0DL200000CA
LED,SAM5670(DL2LRG) BK YGREEN
LD742
0DL233309AC
LED,SAM2333 TP KWANG GREEN/RED
D1
0DD100009AM
EU1ZV(1) TP SANKEN
LD743
0DL233309AC
LED,SAM2333 TP KWANG GREEN/RED
D100
0DD226239AA
CHIP KDS226 SOT23
LD804
0DL233309AC
LED,SAM2333 TP KWANG GREEN/RED
D101
0DD226239AA
CHIP KDS226 SOT23
LD805
0DL233309AC
LED,SAM2333 TP KWANG GREEN/RED
D102
0DD226239AA
CHIP KDS226 SOT23
LD806
0DL233309AC
LED,SAM2333 TP KWANG GREEN/RED
D103
0DD226239AA
CHIP KDS226 SOT23
ZD116
0DR050008AA
SD05.TC R/TP SEMTECH SOD323 5V
D104
0DD226239AA
CHIP KDS226 SOT23
ZD201
0DR050008AA
SD05.TC R/TP SEMTECH SOD323 5V
D105
0DD226239AA
CHIP KDS226 SOT23
ZD750
0DR050008AA
SD05.TC R/TP SEMTECH SOD323 5V
D106
0DD226239AA
CHIP KDS226 SOT23
ZD751
0DR050008AA
SD05.TC R/TP SEMTECH SOD323 5V
D107
0DD226239AA
CHIP KDS226 SOT23
ZD752
0DR050008AA
SD05.TC R/TP SEMTECH SOD323 5V
D108
0DD226239AA
CHIP KDS226 SOT23
D109
0DD226239AA
CHIP KDS226 SOT23
D110
0DD226239AA
CHIP KDS226 SOT23
C003
0CE476SF6DC
47UF MVG 16V M
D111
0DD226239AA
CHIP KDS226 SOT23
C109
0CE107SF6DC
100UF MVG 16V M
D112
0DD226239AA
CHIP KDS226 SOT23
C11
0CE477VF6DC
470UF MV 16V 20%
D113
0DD226239AA
CHIP KDS226 SOT23
C110
0CE107SF6DC
100UF MVG 16V M
D114
0DD226239AA
CHIP KDS226 SOT23
C111
0CE107SF6DC
100UF MVG 16V M
D115
0DD226239AA
CHIP KDS226 SOT23
C112
0CE107SF6DC
100UF MVG 16V M
D117
0DD226239AA
CHIP KDS226 SOT23
C113
0CE107SF6DC
100UF MVG 16V M
D118
0DD226239AA
CHIP KDS226 SOT23
C114
0CE107SF6DC
100UF MVG 16V M
D119
0DD226239AA
CHIP KDS226 SOT23
C115
0CE107SF6DC
100UF MVG 16V M
D120
0DD226239AA
CHIP KDS226 SOT23
C119
0CE477VF6DC
470UF MV 16V 20%
D121
0DD226239AA
CHIP KDS226 SOT23
C121
0CE477VF6DC
470UF MV 16V 20%
D122
0DD226239AA
CHIP KDS226 SOT23
C123
0CE477VF6DC
470UF MV 16V 20%
CAPACITOR
REPLACEMENT PARTS LIST
LOCA. NO
PART NO
DESCRIPTION
LOCA. NO
PART NO
DESCRIPTION
C127
0CE476SF6DC
47UF MVG 16V M
C829
0CE227VF6DC
220UF MV 16V 20%
C13
0CE476SF6DC
47UF MVG 16V M
C832
0CE476SF6DC
47UF MVG 16V M
C134
0CE476SF6DC
47UF MVG 16V M
C835
0CE476SF6DC
47UF MVG 16V M
C14
0CE105SK6DC
1UF MVG 50V M
C838
0CE476SF6DC
47UF MVG 16V M
C15
0CE105SK6DC
1UF MVG 50V M
C840
0CE107SF6DC
100UF MVG 16V M
C150
0CE476SF6DC
47UF MVG 16V M
C842
0CE107SF6DC
100UF MVG 16V M
C154
0CE476SF6DC
47UF MVG 16V M
C845
0CE476SF6DC
47UF MVG 16V M
C158
0CE476SF6DC
47UF MVG 16V M
C848
0CE476SF6DC
47UF MVG 16V M
C16
0CE105SK6DC
1UF MVG 50V M
C849
0CE477VF6DC
470UF MV 16V 20%
C179
0CE476SF6DC
47UF MVG 16V M
C851
0CE477VF6DC
470UF MV 16V 20%
C182
0CE476SF6DC
47UF MVG 16V M
C853
0CE477VF6DC
470UF MV 16V 20%
C185
0CE476SF6DC
47UF MVG 16V M
C856
0CE107SF6DC
100UF MVG 16V M
C2
0CE106SF6DC
10UF MVG 16V 20%
C859
0CE107SF6DC
100UF MVG 16V M
C300
0CE476SF6DC
47UF MVG 16V M
C862
0CE107SF6DC
100UF MVG 16V M
C303
0CE476SF6DC
47UF MVG 16V M
C865
0CE107SF6DC
100UF MVG 16V M
C306
0CE476SF6DC
47UF MVG 16V M
C867
0CE227VF6DC
220UF MV 16V 20%
C311
0CE106SF6DC
10UF MVG 16V 20%
C869
0CE227VF6DC
220UF MV 16V 20%
C316
0CN105EJ56A
1.0UF 3216 35V 10%
C872
0CE476SF6DC
47UF MVG 16V M
C320
0CN105EJ56A
1.0UF 3216 35V 10%
C875
0CE476SF6DC
47UF MVG 16V M
C322
0CE106SF6DC
10UF MVG 16V 20%
C878
0CE106SF6DC
10UF MVG 16V 20%
C344
0CE106SF6DC
10UF MVG 16V 20%
C892
0CE477VF6DC
470UF MV 16V 20%
C348
0CE106SF6DC
10UF MVG 16V 20%
C894
0CE477VF6DC
470UF MV 16V 20%
C4
0CE106SF6DC
10UF MVG 16V 20%
C897
0CE107SF6DC
100UF MVG 16V M
C400
0CN105EJ56A
1.0UF 3216 35V 10%
C900
0CE107SF6DC
100UF MVG 16V M
C401
0CE106SF6DC
10UF MVG 16V 20%
C903
0CE107SF6DC
100UF MVG 16V M
C408
0CE106SF6DC
10UF MVG 16V 20%
C906
0CE107SF6DC
100UF MVG 16V M
C409
0CE107SF6DC
100UF MVG 16V M
C908
0CE477VF6DC
470UF MV 16V 20%
C411
0CK224DF56A
220000PF 2012 16V 10%
C910
0CE477VF6DC
470UF MV 16V 20%
C418
0CK224DF56A
220000PF 2012 16V 10%
C931
0CE107SF6DC
100UF MVG 16V M
C420
0CE106SF6DC
10UF MVG 16V 20%
C933
0CE477VF6DC
470UF MV 16V 20%
C425
0CK224DF56A
220000PF 2012 16V 10%
C935
0CE477VF6DC
470UF MV 16V 20%
C426
0CK224DF56A
220000PF 2012 16V 10%
C938
0CE107SF6DC
100UF MVG 16V M
C427
0CK224DF56A
220000PF 2012 16V 10%
C941
0CE227VF6DC
220UF MV 16V 20%
C436
0CK224DF56A
220000PF 2012 16V 10%
C944
0CE476SF6DC
47UF MVG 16V M
C452
0CE106SF6DC
10UF MVG 16V 20%
C947
0CE476SF6DC
47UF MVG 16V M
C464
0CE476SF6DC
47UF MVG 16V M
C949
0CE477VF6DC
470UF MV 16V 20%
C6
0CE476SF6DC
47UF MVG 16V M
C951
0CE477VF6DC
470UF MV 16V 20%
C8
0CE476SF6DC
47UF MVG 16V M
C954
0CE107SF6DC
100UF MVG 16V M
C800
0CE477VF6DC
470UF MV 16V 20%
C957
0CE476SF6DC
47UF MVG 16V M
C805
0CE477VF6DC
470UF MV 16V 20%
C966
0CE107SF6DC
100UF MVG 16V M
C806
0CE106SF6DC
10UF MVG 16V 20%
C968
0CE106SF6DC
10UF MVG 16V 20%
C808
0CE227VF6DC
220UF MV 16V 20%
C970
0CE106SF6DC
10UF MVG 16V 20%
C812
0CE477VF6DC
470UF MV 16V 20%
C973
0CE106SF6DC
10UF MVG 16V 20%
C814
0CE227VF6DC
220UF MV 16V 20%
C975
0CE227VF6DC
220UF MV 16V 20%
C816
0CE477VF6DC
470UF MV 16V 20%
C977
0CE227VF6DC
220UF MV 16V 20%
C817
0CE106SF6DC
10UF MVG 16V 20%
C980
0CE476SF6DC
47UF MVG 16V M
C818
0CE227VF6DC
220UF MV 16V 20%
C983
0CE107SF6DC
100UF MVG 16V M
C820
0CE107SF6DC
100UF MVG 16V M
C986
0CE476SF6DC
47UF MVG 16V M
C822
0CE107SF6DC
100UF MVG 16V M
C989
0CE107SF6DC
100UF MVG 16V M
C825
0CE107SF6DC
100UF MVG 16V M
C992
0CE107SF6DC
100UF MVG 16V M
C827
0CE227VF6DC
220UF MV 16V 20%
CA101
0CE477DK618
470UF STD 50V 20%
REPLACEMENT PARTS LIST
LOCA. NO
PART NO
DESCRIPTION
LOCA. NO
PART NO
DESCRIPTION
0CE477DK618
470UF STD 50V 20%
CN137
0CE476SF6DC
47UF MVG 16V M
CA104
0CE107DH618
100UF STD 25V M
CN138
0CE105SK6DC
1UF MVG 50V M
CA105
0CE105SK6DC
1UF MVG 50V M
CN141
0CE476SF6DC
47UF MVG 16V M
CA106
0CE106SF6DC
10UF MVG 16V 20%
CN144
0CE476SF6DC
47UF MVG 16V M
CA107
0CQ6821N509
0.0068U 100V K
CN145
0CE476SF6DC
47UF MVG 16V M
CA108
0CE107DH618
100UF STD 25V M
CN147
0CE476SF6DC
47UF MVG 16V M
CA109
0CQ6821N509
0.0068U 100V K
CN149
0CE476SF6DC
47UF MVG 16V M
CA110
0CE477DK618
470UF STD 50V 20%
CA111
0CE477DK618
470UF STD 50V 20%
CA112
0CE106SF6DC
10UF MVG 16V 20%
L800
6140VB0004B
COIL,CHOKE 26UH 1UEWPHY 22.5TURN
CA113
181-120K
2200PF 4KV M E
L801
6140VB0004B
COIL,CHOKE 26UH 1UEWPHY 22.5TURN
CA114
181-120K
2200PF 4KV M E
L803
150-C02F
CA115
0CE477DK618
470UF STD 50V 20%
CA116
0CE107DH618
100UF STD 25V M
CA117
0CE477DK618
470UF STD 50V 20%
P102
380-068B
CA118
0CQ1041N509
0.1U 100V
P103
6612BBBHN6A
JACK,DIN 4400621 AMP DVI INTERACED
CA119
0CE227VF6DC
220UF MV 16V 20%
P103A
6612VLH001A
JACK,RCA SP022B 2P BK/RD
CA120
0CE106SF6DC
10UF MVG 16V 20%
P103B
6612VLH001A
JACK,RCA SP022B 2P BK/RD
CA121
0CQ1041N509
0.1U 100V
P120
380-068B
JACK,PHONE 3.5 EARPHONE WITH SW
CA122
0CE227VF6DC
220UF MV 16V 20%
PN101
380-363J
JACK,DIN
CA125
0CE107SF6DC
100UF MVG 16V M
PN102
6612JH003CA
JACK,RCA PPJ137A AUDIO LMONO JACK
CA126
0CE474SK6DC
0.47UF MVG 50V M
PN103
6612VMV002A
JACK,DRAWING UCTEX020 UGCOM BNC MONO
CA127
0CE474SK6DC
0.47UF MVG 50V M
PN104
6612J00010A
JACK,RCA PPJ128A1 A/V 2P MONO
CA128
0CE335SK6DC
3.3UF MVG 50V 20%
PN105
6612JH003CA
JACK,RCA PPJ137A AUDIO LMONO JACK
CA129
0CE107SF6DC
100UF MVG 16V M
CA131
0CE106SF6DC
10UF MVG 16V 20%
CA132
0CE474SK6DC
0.47UF MVG 50V M
P002A
387-B04J
CONNECTOR ASSEMBLY,4P 2.5MM
CA133
0CE474SK6DC
0.47UF MVG 50V M
P1
387-B04J
CONNECTOR ASSEMBLY,4P 2.5MM
CA134
0CE106SF6DC
10UF MVG 16V 20%
P101
6630VGA001C
CONNECTOR,DSUB 15PIN 2.29MM
CA135
0CE106SF6DC
10UF MVG 16V 20%
P104
6630VGA001C
CONNECTOR,DSUB 15PIN 2.29MM
CA139
0CE106SF6DC
10UF MVG 16V 20%
P2
387-A03J
CONNECTOR ASSEMBLY,3P 2.5MM
CA140
0CE107SF6DC
100UF MVG 16V M
P741
CA153
0CE107SF6DC
100UF MVG 16V M
P802A
CA154
0CE476SF6DC
47UF MVG 16V M
CA154
0CE476SF6DC
47UF MVG 16V M
CA155
0CE106SF6DC
10UF MVG 16V 20%
AR200
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
CA156
0CE476SF6DC
47UF MVG 16V M
AR201
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
CA404
0CE476SF6DC
47UF MVG 16V M
AR202
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
CA751
0CE105SK6DC
1UF MVG 50V M
AR203
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
CN113
0CE476SF6DC
47UF MVG 16V M
AR204
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
CN114
0CE476SF6DC
47UF MVG 16V M
AR205
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
CN115
0CE476SF6DC
47UF MVG 16V M
AR206
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
CN119
0CE105SK6DC
1UF MVG 50V M
AR207
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
CN120
0CE105SK6DC
1UF MVG 50V M
AR208
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
CN121
0CE105SK6DC
1UF MVG 50V M
AR209
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
CN122
0CE105SK6DC
1UF MVG 50V M
AR210
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
CN123
0CE105SK6DC
1UF MVG 50V M
AR211
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
CN124
0CE476SF6DC
47UF MVG 16V M
AR260
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
CN127
0CE105SK6DC
1UF MVG 50V M
AR261
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
CN130
0CE105SK6DC
1UF MVG 50V M
AR262
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
CN133
0CE105SK6DC
1UF MVG 50V M
AR263
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
CA102
K
K
COIL
COIL,CHOKE 82UH
JACK
JACK,PHONE 3.5 EARPHONE WITH SW
PJ6046F H=8.0 W/O S/W,W/SHIELD
CONNECTOR
6630VGA004B
387-A03J
CONNECTOR,DSUB 9P 2.77MM
CONNECTOR ASSEMBLY,3P 2.5MM
RESISTOR
REPLACEMENT PARTS LIST
LOCA. NO
PART NO
DESCRIPTION
LOCA. NO
AR264
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
RA101
AR265
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
AR266
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
AR267
0RRZVTA001D
AR268
PART NO
DESCRIPTION
0RS2701K607
2.7K OHM 2 W 5.00%
RA102
0RS2701K607
2.7K OHM 2 W 5.00%
RA105
0RD4700H609
470 OHM 1/2 W 5.00%
22 OHM 1 / 16 W 1608 5%
RA109
0RD4700H609
470 OHM 1/2 W 5.00%
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
RA114
0RS0221H609
2.2 OHM 1/2 W 5.00%
AR269
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
RA117
0RS0221H609
2.2 OHM 1/2 W 5.00%
AR270
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
AR271
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
AR400
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
SW001
140-315A
SWITCH,TACT SKHV17910B 12V
AR401
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
SW002
140-315A
SWITCH,TACT SKHV17910B 12V
AR402
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
SW003
140-315A
SWITCH,TACT SKHV17910B 12V
AR403
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
SW004
140-315A
SWITCH,TACT SKHV17910B 12V
AR460
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
SW005
140-315A
SWITCH,TACT SKHV17910B 12V
AR461
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
SW006
140-315A
SWITCH,TACT SKHV17910B 12V
AR462
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
SW101
140-275A
SWITCH,PUSH JDPB21SA EVLAND NON 30V
AR463
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
SW742
140-275A
SWITCH,PUSH JDPB21SA EVLAND NON 30V
AR464
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
SW800
6600VM2006A
AR465
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
AR466
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
AR467
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
L100
6210VC0005A
FILTER,EMC BK2125 HS 750
AR468
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
L101
6210VC0005A
FILTER,EMC BK2125 HS 750
AR469
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
L135
6200JB8007L
FILTER,EMC HH2012 1M221JT
AR470
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
L136
6200JB8007L
FILTER,EMC HH2012 1M221JT
AR471
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
L137
6200JB8007L
FILTER,EMC HH2012 1M221JT
AR472
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
L138
6200JB8007L
FILTER,EMC HH2012 1M221JT
AR473
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
L150
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
AR474
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
L300
6210VC0005A
FILTER,EMC BK2125 HS 750
AR475
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
L301
6210VC0005A
FILTER,EMC BK2125 HS 750
AR500
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
L302
6210VC0005A
FILTER,EMC BK2125 HS 750
AR501
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
L411
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
AR502
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
L460
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
AR503
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
L806
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
AR504
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
L807
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
AR505
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
L808
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
AR506
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
L809
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
AR507
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
L810
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
AR508
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
L811
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
AR509
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
L850
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
AR510
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
L851
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
AR511
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
L852
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
AR512
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
L853
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
AR513
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
L854
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
AR514
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
L855
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
AR515
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
L856
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
AR516
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
L857
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
AR517
0RRZVTA001D
22 OHM 1 / 16 W 1608 5%
L858
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
AR550
0RRZVTA001C
4.7K OHM 1 / 16 W 1608 5%
L859
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
AR551
0RRZVTA001C
4.7K OHM 1 / 16 W 1608 5%
L860
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
AR552
0RRZVTA001C
4.7K OHM 1 / 16 W 1608 5%
L861
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
AR553
0RRZVTA001C
4.7K OHM 1 / 16 W 1608 5%
L862
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
R22
0RD0152H609
15 OHM 1/2 W 5.00% TA52
L863
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
SWITCH
SWITCH,PUSH SDDF3PATP011 250V
FILTER & CRYSTAL
REPLACEMENT PARTS LIST
LOCA. NO
PART NO
DESCRIPTION
L864
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
L865
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
L866
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
L867
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
L868
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
L871
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
L872
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
L873
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
L874
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
L875
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
L876
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
L877
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
L880
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
L881
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
L882
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
L883
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
L884
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
L885
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
L886
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
L887
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
L889
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC SQE2222 714MH 0.37PHY
LA101
150-F09A
LA102
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
LA104
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
LA105
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
LA106
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
LN107
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
LN108
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
LN109
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
LT300
6200C000010
FILTER,B.P. H354LAIK5202
LT301
6200C000010
FILTER,B.P. H354LAIK5202
LT302
6200C000009
FILTER,B.P. H354LAIK5225
R30
6210VC0006A
FILTER,EMC FBMH3216 HM501NT
X300
6212AB2015B
RESONATOR,CRYSTAL HC49/SM5H 20MHZ +/ 30 PPM
X400
6202VDT002E
RESONATOR,CRYSTAL SX1SMD 20250000HZ 30PPM
X601
156-A02M
RESONATOR,CRYSTAL HC49U 18.432MHZ 30PPM
X700
6212AB2015C
RESONATOR,CRYSTAL HC49/SM4H 25MHZ +/ 50 PPM
MISCELLANEOUS
P001
6726VV0006K
REMOTE CONTROLLER RECEIVER,38KHZ
ACCESSORIES
A1
3828VA0352L
MANUAL,OWNERS MU50PZ41VS ZENITH
A2
6710V00092Q
REMOTE CONTROLLER,MU50PZ41S ZENITH
A3
6410VUH005A
POWER CORD,PS204 125V/13A VOLEX UL/CSA
A4
6612VMV002B
JACK,DRAWING UCTEX031 UGCOM
A5
6850V00001A
CABLE,FLAT 15660751 DVI A/D TO A/D 2000MM
A6
6866VA9001B
CONNECTOR ,DSUB
29909C UL 1161 AWG
LOCA. NO
PART NO
DESCRIPTION
PRINTED CIRCUIT BOARD
A/V NTSC(TOP)
INTERFACE FIX(TOP)
MAIN(TOP)
INTERFACE FIX(BOTTOM)
A/V NTSC(BOTTOM)
FAN CONTROL(TOP)
FAN CONTROL(BOTTOM)
LOCAL KEY(TOP)
AUDIO(TOP)
LOCAL KEY(BOTTOM)
MAIN(BOTTOM)
POWER S/W(TOP)
POWER S/W(BOTTOM)
AUDIO(BOTTOM)
RIGHT SPK(TOP)
PRE-AMP(TOP)
PRE-AMP(BOTTOM)
RIGHT SPK(BOTTOM)