Cub Cadet 3X 24HD Operator`s manual

Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty
Operator’s Manual
Three Stage Snow Thrower — 3X 24, 3X 26, 3X 28, 3X 24 HD, 3X
26 HD, 3X 28 HD, & 3X 30 HD
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL
BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
Printed In USA
Form No. 769-09764
(May 29, 2014)
1
To The Owner
Thank You
Thank you for purchasing a Cub Cadet Snow Thrower. It was
carefully engineered to provide excellent performance when
properly operated and maintained.
If applicable, the power testing information used to establish
the power rating of the engine equipped on this machine can be
found at www.opei.org or the engine manufacturer’s web site.
Please read this entire manual prior to operating the equipment.
It instructs you how to safely and easily set up, operate and
maintain your machine. Please be sure that you, and any other
persons who will operate the machine, carefully follow the
recommended safety practices at all times. Failure to do so could
result in personal injury or property damage.
If you have any problems or questions concerning the machine,
phone your local Cub Cadet dealer or contact us directly. Cub
Cadet’s Customer Support telephone numbers, website address
and mailing address can be found on this page. We want to
ensure your complete satisfaction at all times.
All information in this manual is relative to the most recent
product information available at the time of printing. Review
this manual frequently to familiarize yourself with the machine,
its features and operation. Please be aware that this Operator’s
Manual may cover a range of product specifications for various
models. Characteristics and features discussed and/or illustrated
in this manual may not be applicable to all models. We reserve
the right to change product specifications, designs and
equipment without notice and without incurring obligation.
Table of Contents
Throughout this manual, all references to right and left side of the
machine are observed from the operating position.
The engine manufacturer is responsible for all engine-related
issues with regards to performance, power-rating, specifications,
warranty and service. Please refer to the engine manufacturer’s
Owner’s/Operator’s Manual, packed separately with your
machine, for more information.
Safe Operation Practices......................................... 3
Assembly & Set-Up................................................... 7
Controls....................................................................15
Operation.................................................................18
Maintenance & Adjustment..................................19
Service..................................................................... 23
Troubleshooting..................................................... 25
Replacement Parts................................................. 26
Attachments........................................................... 27
Warranty...................................................Back Cover
Record Product Information
Model Number
Before setting up and operating your new equipment, please
locate the model plate on the equipment and record the
information in the provided area to the right. You can locate the
model plate by standing at the operator’s position and looking
down at the rear of the frame. This information will be necessary,
should you seek technical support via our web site, Customer
Support Department, or with a local authorized service dealer.
Serial Number
Product Registration and Customer Support
Please register your product on our website, www.cubcadet.com.
If you have difficulty assembling this product or have any questions regarding the controls, operation, or maintenance of
this machine, you can seek help from the experts. Choose from the options below:
◊
Visit us on the web at www.cubcadet.com
See How-to Maintenance and Parts Installation Videos at www.cubcadet.com/tutorials
2
◊
Call a Customer Support Representative at (800) 965-4CUB
◊
Locate your nearest Cub Cadet Dealer at (877) 282-8684
◊
Write to Cub Cadet LLC • P.O. Box 361131 • Cleveland, OH • 44136-0019
Important Safe Operation Practices
2
WARNING! This symbol points out important safety instructions which, if not followed,
could endanger the personal safety and/or property of yourself and others. Read and follow
all instructions in this manual before attempting to operate this machine. Failure to comply
with these instructions may result in personal injury.
When you see this symbol. HEED ITS WARNING!
CALIFORNIA PROPOSITION 65
WARNING! Engine Exhaust, some of its constituents, and certain vehicle components
contain or emit chemicals known to State of California to cause cancer and birth defects
or other reproductive harm.
DANGER: This machine was built to be operated according to the safe operation practices in
this manual. As with any type of power equipment, carelessness or error on the part of the
operator can result in serious injury. This machine is capable of amputating fingers, hands,
toes and feet and throwing foreign objects. Failure to observe the following safety
instructions could result in serious injury or death.
Training
Preparation
1.
Read, understand, and follow all instructions on the
machine and in the manual(s) before attempting to
assemble and operate. Keep this manual in a safe place for
future and regular reference and for ordering replacement
parts.
Thoroughly inspect the area where the equipment is to be used.
Remove all doormats, newspapers, sleds, boards, wires and other
foreign objects, which could be tripped over or thrown by the
auger/impeller.
2.
Be familiar with all controls and their proper operation.
Know how to stop the machine and disengage them
quickly.
3.
1.
Always wear safety glasses or eye shields during operation
and while performing an adjustment or repair to protect
your eyes. Thrown objects which ricochet can cause serious
injury to the eyes.
Never allow children under 14 years of age to operate this
machine. Children 14 and over should read and understand
the instructions and safe operation practices in this manual
and on the machine and be trained and supervised by an
adult.
2.
Do not operate without wearing adequate winter outer
garments. Do not wear jewelry, long scarves or other loose
clothing, which could become entangled in moving parts.
Wear footwear which will improve footing on slippery
surfaces.
4.
Never allow adults to operate this machine without proper
instruction.
3.
Use a grounded three-wire extension cord and receptacle
for all machines with electric start engines.
5.
Thrown objects can cause serious personal injury. Plan
your snow-throwing pattern to avoid discharge of material
toward roads, bystanders and the like.
4.
Adjust auger housing height to clear gravel or crushed rock
surfaces.
6.
Keep bystanders, pets and children at least 75 feet from the
machine while it is in operation. Stop machine if anyone
enters the area.
5.
Disengage all control levers before starting the engine.
6.
7.
Exercise caution to avoid slipping or falling, especially
when operating in reverse.
Never attempt to make any adjustments while engine is
running, except where specifically recommended in the
operator’s manual.
7.
Let engine and machine adjust to outdoor temperature
before starting to clear snow.
3
Safe Handling of Gasoline
5.
To avoid personal injury or property damage use extreme care
in handling gasoline. Gasoline is extremely flammable and the
vapors are explosive. Serious personal injury can occur when
gasoline is spilled on yourself or your clothes which can ignite.
Wash your skin and change clothes immediately.
Never run an engine indoors or in a poorly ventilated area.
Engine exhaust contains carbon monoxide, an odorless
and deadly gas.
6.
Do not operate machine while under the influence of
alcohol or drugs.
7.
Muffler and engine become hot and can cause a burn. Do
not touch. Keep children away.
a.
Use only an approved gasoline container.
b.
Extinguish all cigarettes, cigars, pipes and other
sources of ignition.
8.
Exercise extreme caution when operating on or crossing
gravel surfaces. Stay alert for hidden hazards or traffic.
c.
Never fuel machine indoors.
9.
d.
Never remove gas cap or add fuel while the engine is
hot or running.
Exercise caution when changing direction and while
operating on slopes. Do not operate on steep slopes.
10.
e.
Allow engine to cool at least two minutes before
refueling.
Plan your snow-throwing pattern to avoid discharge
towards windows, walls, cars etc. Thus, avoiding possible
property damage or personal injury caused by a ricochet.
f.
Never over fill fuel tank. Fill tank to no more than ½
inch below bottom of filler neck to provide space for
fuel expansion.
11.
Never direct discharge at children, bystanders and pets or
allow anyone in front of the machine.
g.
Replace gasoline cap and tighten securely.
h.
If gasoline is spilled, wipe it off the engine and
equipment. Move machine to another area. Wait 5
minutes before starting the engine.
i.
Never store the machine or fuel container inside
where there is an open flame, spark or pilot light
(e.g. furnace, water heater, space heater, clothes
dryer etc.).
j.
Allow machine to cool at least 5 minutes before
storing.
k.
Never fill containers inside a vehicle or on a truck
or trailer bed with a plastic liner. Always place
containers on the ground away from your vehicle
before filling.
l.
If possible, remove gas-powered equipment from
the truck or trailer and refuel it on the ground. If this
is not possible, then refuel such equipment on a
trailer with a portable container, rather than from a
gasoline dispenser nozzle.
m. Keep the nozzle in contact with the rim of the fuel
tank or container opening at all times until fueling is
complete. Do not use a nozzle lock-open device.
Operation
1.
4
Do not put hands or feet near rotating parts, in the auger/
impeller housing or chute assembly. Contact with the
rotating parts can amputate hands and feet.
2.
The auger/impeller control lever is a safety device. Never
bypass its operation. Doing so makes the machine unsafe
and may cause personal injury.
3.
The control levers must operate easily in both directions
and automatically return to the disengaged position when
released.
4.
Never operate with a missing or damaged chute assembly.
Keep all safety devices in place and working.
Section 2 — Important Safe Operation Practices
12. Do not overload machine capacity by attempting to clear
snow at too fast of a rate.
13.
Never operate this machine without good visibility or light.
Always be sure of your footing and keep a firm hold on the
handles. Walk, never run.
14. Disengage power to the auger/impeller when transporting
or not in use.
15.
Never operate machine at high transport speeds on
slippery surfaces. Look down and behind and use care
when backing up.
16. If the machine should start to vibrate abnormally, stop
the engine, disconnect the spark plug wire and ground it
against the engine. Inspect thoroughly for damage. Repair
any damage before starting and operating.
17.
Disengage all control levers and stop engine before you
leave the operating position (behind the handles). Wait
until the auger/impeller comes to a complete stop before
unclogging the chute assembly, making any adjustments,
or inspections.
18. Never put your hand in the discharge or collector openings.
Always use the clean-out tool provided to unclog the
discharge opening. Do not unclog chute assembly while
engine is running. Shut off engine and remain behind
handles until all moving parts have stopped before
unclogging.
19.
Use only attachments and accessories approved by the
manufacturer (e.g. wheel weights, tire chains, cabs etc.).
20.
When starting engine, pull cord slowly until resistance
is felt, then pull rapidly. Rapid retraction of starter cord
(kickback) will pull hand and arm toward engine faster than
you can let go. Broken bones, fractures, bruises or sprains
could result.
21.
If situations occur which are not covered in this manual, use
care and good judgment. Contact Customer Support for
assistance and the name of your nearest servicing dealer.
Clearing a Clogged Discharge Chute
1.
SHUT THE ENGINE OFF!
14. According to the Consumer Products Safety Commission
(CPSC) and the U.S. Environmental Protection Agency (EPA),
this product has an Average Useful Life of seven (7) years,
or 60 hours of operation. At the end of the Average Useful
Life have the machine inspected annually by an authorized
service dealer to ensure that all mechanical and safety
systems are working properly and not worn excessively.
Failure to do so can result in accidents, injuries or death.
2.
Wait 10 seconds to be sure the impeller blades have
stopped rotating.
Do not modify engine
3.
Always use a clean-out tool, not your hands.
Hand contact with the rotating impeller inside the discharge
chute is the most common cause of injury associated with snow
throwers. Never use your hand to clean out the discharge chute.
To clear the chute:
Maintenance & Storage
1.
Never tamper with safety devices. Check their proper
operation regularly. Refer to the maintenance and
adjustment sections of this manual.
2.
Before cleaning, repairing, or inspecting machine
disengage all control levers and stop the engine. Wait until
the auger/impeller come to a complete stop. Disconnect
the spark plug wire and ground against the engine to
prevent unintended starting.
3.
Check bolts and screws for proper tightness at frequent
intervals to keep the machine in safe working condition.
Also, visually inspect machine for any damage.
4.
Do not change the engine governor setting or over-speed
the engine. The governor controls the maximum safe
operating speed of the engine.
5.
Snow thrower shave plates and skid shoes are subject to
wear and damage. For your safety protection, frequently
check all components and replace with original equipment
manufacturer’s (OEM) parts only. “Use of parts which do
not meet the original equipment specifications may lead to
improper performance and compromise safety!”
6.
Check control levers periodically to verify they engage
and disengage properly and adjust, if necessary. Refer
to the adjustment section in this operator’s manual for
instructions.
7.
Maintain or replace safety and instruction labels, as
necessary.
8.
Observe proper disposal laws and regulations for gas, oil,
etc. to protect the environment.
9.
Prior to storing, run machine a few minutes to clear snow
from machine and prevent freeze up of auger/impeller.
10.
Never store the machine or fuel container inside where
there is an open flame, spark or pilot light such as a water
heater, furnace, clothes dryer etc.
11.
Always refer to the operator’s manual for proper
instructions on off-season storage.
To avoid serious injury or death, do not modify engine in any
way. Tampering with the governor setting can lead to a runaway
engine and cause it to operate at unsafe speeds. Never tamper
with factory setting of engine governor.
Notice Regarding Emissions
Engines which are certified to comply with California and federal
EPA emission regulations for SORE (Small Off Road Equipment)
are certified to operate on regular unleaded gasoline, and
may include the following emission control systems: Engine
Modification (EM), Oxidizing Catalyst (OC), Secondary Air
Injection (SAI) and Three Way Catalyst (TWC) if so equipped.
Spark Arrestor
WARNING! This machine is equipped with an
internal combustion engine and should not be used
on or near any unimproved forest-covered, brush
covered or grass-covered land unless the engine’s
exhaust system is equipped with a spark arrestor
meeting applicable local or state laws (if any).
If a spark arrestor is used, it should be maintained in effective
working order by the operator. In the State of California the
above is required by law (Section 4442 of the California Public
Resources Code). Other states may have similar laws. Federal laws
apply on federal lands.
A spark arrestor for the muffler is available through your
nearest engine authorized service dealer or contact the service
department, P.O. Box 361131 Cleveland, Ohio 44136-0019.
12. Check fuel line, tank, cap, and fittings frequently for cracks
or leaks. Replace if necessary.
13.
Do not crank engine with spark plug removed.
Section 2 — Important Safe Operation Practices
5
Safety Symbols
This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the
machine before attempting to assemble and operate.
Symbol
Description
READ THE OPERATOR’S MANUAL(S)
Read, understand, and follow all instructions in the manual(s) before attempting to
assemble and operate
WARNING— ROTATING BLADES
Keep hands out of inlet and discharge openings while machine is running. There are rotating
blades inside
WARNING— ROTATING BLADES
Keep hands out of inlet and discharge openings while machine is running. There are rotating
blades inside
WARNING— ROTATING AUGER
Do not put hands or feet near rotating parts, in the auger/impeller housing or chute
assembly. Contact with the rotating parts can amputate hands and feet.
WARNING—THROWN OBJECTS
This machine may pick up and throw objects which can cause serious personal injury.
WARNING—GASOLINE IS FLAMMABLE
Allow the engine to cool at least two minutes before refueling.
WARNING— CARBON MONOXIDE
Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon
monoxide, an odorless and deadly gas.
WARNING— ELECTRICAL SHOCK
Do not use the engine’s electric starter in the rain
WARNING— HOT SURFACE
Engine parts, especially the muffler, become extremely hot during operation. Allow engine
and muffler to cool before touching.
WARNING! Your Responsibility—Restrict the use of this power machine to persons who read, understand and
follow the warnings and instructions in this manual and on the machine.
SAVE THESE INSTRUCTIONS!
6
Section 2 — Important Safe Operation Practices
3
Assembly & Set-Up
Contents of Carton
•
Snow Thrower
•
Replacement Auger Shear Pins
•
Chute Assembly
•
Chute Control Rod or Flex Shaft
•
Engine Manual
•
Product Registration Card
•
Snow Thrower Operator’s Manual
There are two chute control styles available that determine your method of assembly. Refer to the image above to determine which
chute control style you have. If your product resembles the image on the left (above), see page 8 for assembly instructions. If your
product resembles the image on the right (above), see page 10 for assembly instructions.
7
Assembly (If Equipped with 4-Way Chute Control)
4.
Remove all loose parts before assembling.
Handle Assembly
1.
Place the shift lever in the Forward-6 position as shown in
Figure 3-1 inset.
2.
Cut zip ties securing chute control rod to the lower handle
and set it aside.
3.
Observe the lower rear area of the snow thrower to be sure
both cables are aligned with roller guides before pivoting
the handle upward. Pivot the handle upward.
Secure the handle by tightening the plastic knob located
on both the left and right sides of the handle. Remove
and discard any rubber bands, if present. They are for
packaging purposes only.
Chute Assembly
1.
Remove hairpin clip, wing nut and hex screw from chute
control head and clevis pin and bow-tie cotter pin from
chute support bracket. See Figure 3-3.
Chute Control Head
Chute Support
Bracket
Chute
Chute Base
Figure 3-3
2.
Figure 3-1
Insert chute control rod into chute control head. Push rod
as far into chute control head as possible, keeping the
holes in the rod pointing upward. See Figure 3-4.
NOTE: Make certain the cables are seated properly in the
roller guides. See Figure 3-2.
Figure 3-4
3.
Figure 3-2
8
Section 3— Assembly & Set-Up
Place chute onto chute base and ensure chute control
rod is positioned under the handle panel. Install hex bolt
previously removed but do not secure with wing nut at this
time. See Figure 3-5.
5.
Rotate the joystick to the one o’clock position so that the
silver indicator arrow on the pinion gear below the control
panel faces upward. See Figure 3-7.
Figure 3-5
4.
Squeeze the trigger on the joystick and rotate the chute by
hand to face forward. The holes in the chute control input
will be facing up. See Figure 3-6.
Chute Control
Input
Top View
Figure 3-7
NOTE: The joystick will be angled slightly to the right at the
one o’clock position. See “Top View” in Figure 3-6.
6.
Insert the chute control rod into the pinion gear below the
joystick. Make sure to line up the hole in the rod with the
arrow on the pinion gear. See Figure 3-8.
Figure 3-6
NOTE: The chute will not rotate without squeezing the
trigger on the joystick.
Figure 3-8
NOTE: The chute control rod will fit snuggly into the pinion
gear. Support the rear of the dash panel with one hand
while inserting the rod with your other hand to ensure the
rod is inserted all the way into the pinion gear.
NOTE: The hole is a reference for aligning the rod with the
indicator arrow on the pinion gear, and will be visible after
the rod has been inserted.
Section 3 — Assembly & Set-Up
9
7.
Push the chute control rod toward the control panel until
the hole in the rod lines up with the hole in the chute
control input closest to the chute control head and insert
the hairpin clip removed earlier. See Figure 3-9.
Assembly (If Equipped with Overhead Chute Control)
Handle Assembly
1.
Loosen the top two lock nuts securing the upper and lower
handle and remove the two carriage screws from the lower
handle and set aside as shown in Figure 3-11.
Figure 3-9
8.
9.
NOTE: The second hole is used to achieve further
engagement of the chute control rod into the pinion
gear if required. Refer to page 24 for Chute Control Rod
adjustments.
2.
Place the shift lever in the Forward-6 position.
Finish securing chute control head to chute support
bracket with wing nut, clevis pin, and bow-tie cotter pin
removed in step 1. See Figure 3-3.
3.
Cut zip ties securing flex shaft to the lower handle and set
the flex shaft aside.
4.
Remove rubber bands securing cables to carriage screws
and cut zip tie securing shift rod to lower handle. Carefully
pivot the handle upward. See Figure 3-12.
Check that all cables are properly routed through the cable
guide on top of the engine. See Figure 3-10.
Figure 3-11
NOTE: You will need to lower shift rod to the side slightly
to manuever the handle panel over it when pivoting the
handle upward.
Figure 3-10
NOTE: For smoothest operation, the cables should all be to
the left of the chute directional control rod.
10
Section 3— Assembly & Set-Up
Figure 3-12
NOTE: Make certain the cables are seated properly in the
roller guides. See Figure 3-13.
Chute Assembly
1.
Remove the lock nuts and hex screws from chute support
bracket. Position the chute assembly over the chute base.
See Figure 3-15.
Chute Control
Head
1
2
Chute
Assembly
1
2
Chute Base
Figure 3-13
5.
Chute
Support
Bracket
Reattach the two carriage screws and lock nuts removed
earlier as shown in Figure 3-14.
Figure 3-15
2.
Place chute assembly onto chute base.
3.
Secure chute control head to chute support bracket with
the lock nuts and hex screws removed earlier. See Figure
3-16.
Figure 3-14
6.
Finish securing the handle by tightening the top two lock
nuts loosened earlier. Remove and discard any remaining
rubber bands, if present. They are for packaging purposes
only.
Figure 3-16
Section 3 — Assembly & Set-Up
11
4.
Remove the hairpin clip from the rear of the chute control
assembly.
5.
Insert flex shaft removed earlier from the lower handle
into rear of the chute directional control head. Secure the
flex shaft to the chute control head with the hairpin clip
removed earlier. See Figure 3-17 .
7.
Remove the cotter pin and washer from the ferrule on the
end of the shift rod. See Figure 3-19 inset.
8.
Insert the ferrule into the top hole of the shift lever and
secure with the cotter pin and washer removed in the
previous step.
9.
Check that all cables are properly routed through the cable
guide on top of the engine. See Figure 3-10.
Figure 3-19
Figure 3-17
6.
Insert the flex shaft into the chute control rod coupling
under the dash panel. See Figure 3-18.
Set-Up
Shear Pins Storage
Replacement auger shear pins and bow tie cotter pins are
included with your snow thrower. Store them in your snow
thrower’s dash panel until needed. See Figure 3-20.
Figure 3-18
Figure 3-20
12
Section 3— Assembly & Set-Up
Chute Clean-Out Tool
Tire Pressure
WARNING! Under any circumstance do not exceed
manufacturer’s recommended psi. Equal tire
pressure should be maintained at all times. Excessive
pressure when seating beads may cause tire/rim
assembly to burst with force sufficient to cause
serious injury. Refer to sidewall of tire for
recommended pressure.
The chute clean-out tool is fastened to the top of the auger
housing with a mounting clip and a cable tie at the factory. Cut
the cable tie before operating the snow thrower. See Figure 3-21.
Chute Clean-Out
Tool
The tires are over-inflated for shipping purposes. Check the tire
pressure before operating the snow thrower. Refer to the tire side
wall for tire manufacturer’s recommended psi and deflate (or
inflate) the tires as necessary.
NOTE: Equal tire pressure is to be maintained at all times for
performance purposes.
Adjustments
Skid Shoes
The snow thrower skid shoes are adjusted at the factory for
shipping purposes. Adjust them downward, if desired, prior to
operating the snow thrower.
CAUTION: It is not recommended that you operate
this snow thrower on gravel as it can easily pick up and
throw loose gravel, causing personal injury or damage
to the snow thrower and surrounding property.
Figure 3-21
Drift Cutters (If Equipped)
•
The snow thrower drift cutters are mounted inverted at the
factory for shipping purposes.
For close snow removal on a smooth surface, raise skid
shoes higher on the auger housing.
•
Use a middle or lower position when the area to be cleared
is uneven, such as a gravel driveway
1.
Remove the four flange nuts (two on each side) and
carriage bolts. Place drift cutter in upright position and
re-secure. See Figure 3-22.
NOTE: If you choose to operate the snow thrower on a gravel
surface, keep the skid shoes in position for maximum clearance
between the ground and the shave plate.
Figure 3-22
Section 3 — Assembly & Set-Up
13
To adjust the skid shoes:
1.
Loosen the four hex nuts (two on each side) and carriage
bolts. Move skid shoes to desired position. See Figure 3-23.
4.
Allow the auger to remain engaged for approximately ten
(10) seconds before releasing the auger control. Repeat this
several times.
5.
With the auger control in the disengaged “up” position,
walk to the front of the machine.
6.
Confirm that the auger has completely stopped rotating
and shows NO signs of motion. If the auger shows ANY
signs of rotating, immediately return to the operator’s
position and shut off the engine. Wait for ALL moving parts
to stop before readjusting the auger control.
7.
To readjust the control cable, loosen the upper hex screw
on the auger cable bracket.
8.
Position the bracket upward to provide more slack (or
downward to increase cable tension). See Figure 3-24.
Figure 3-23
2.
Make certain the entire bottom surface of skid shoe is
against the ground to avoid uneven wear on the skid shoes.
3.
Retighten nuts and bolts securely.
NOTE: The skid shoes on your snow thrower may look
slightly different (and have different hardware) than the
ones shown in Figure 3-23.
Auger Control
WARNING! Prior to operating your snow thrower,
carefully read and follow all instructions below.
Perform all adjustments to verify your snow thrower
is operating safely and properly.
Refer to the Controls and Features section for the location of the
auger control and check the adjustment as follows:
14
1.
When the auger control is released and in the disengaged
“up” position, the cable should have very little slack. It
should NOT be tight.
2.
In a well-ventilated area, start the snow thrower engine.
Refer to your Engine Operator’s Manual.
3.
While standing in the operator’s position (behind the snow
thrower), engage the auger.
Section 3— Assembly & Set-Up
Figure 3-24
9.
Retighten the upper hex screw.
10.
Repeat steps 2 through 6 above to verify proper
adjustment has been achieved.
4
Controls and Features
Shift Lever 4-Way Chute Directional Control/
Two-Way Chute-Pitch Control †
Drive Control
Auger Control
Headlight
Heated Grips †
Chute Assembly
Steering Trigger Control
Drift Cutter †
Clean Out
Tool
Overhead Chute
Directional Control †
Augers
Skid Shoe
† If Equipped
Figure 4-1
Snow thrower controls and features are described below and
illustrated in Figure 4-1.
Shift Lever
The shift lever is located in the right side of the
handle panel and is used to determine ground
speed and direction of travel.
Forward
There are six forward (F) speeds. Position one (1) is
the slowest and position six (6) is the fastest.
Reverse
There are two reverse (R) speeds. One (1) is the
slower and two (2) is the faster.
Skid Shoes
Position the skid shoes based on surface conditions. Adjust
upward for hard-packed snow. Adjust downward when
operating on gravel or crushed rock surfaces. See Set-Up &
Assembly section.
Augers
When engaged, the augers rotate and draw snow into the auger
housing.
Chute Assembly
Snow drawn into the auger housing is discharged out the chute
assembly.
Headlight
The headlight is located on the handle panel and is automatically
turned on when the engine is started.
15
Auger Control
Heated Grips (If so Equipped)
CAUTION: It is recommended that you wear
gloves when using the heated grip. If the heated
grip become too hot, turn it off.
The auger control is located on the left handle. Squeeze the
control grip against the handle to engage the augers and start
snow throwing action. Release to stop.
To activate the heated grips, move the switch found on the rear
of the dash panel into the ON position. To turn off the heated
grips, move the switch found on the rear of the dash panel to the
OFF position.
Steering Trigger Controls
Drive Control / Auger Clutch Lock
The drive control is located on the right handle. Squeeze the
control grip against the handle to engage the wheel drive.
Release to stop.
The drive control also locks the auger control so that you can
operate the chute directional control without interrupting
the snow throwing process. If the auger control is engaged
simultaneously with the drive control, the operator can release
the auger control (on the left handle) and the augers will remain
engaged. Release both controls to stop the augers and wheel
drive.
Note: Always release the drive control before changing speeds.
Failure to do so will result in increased wear on your machine’s
drive system.
16
Section 4 — Controls and Features
The left and right wheel steering trigger controls are located on
the underside of the handles.
•
Squeeze the right control to turn right.
•
Squeeze the left control to turn left.
CAUTION: Operate the snow thrower in open
areas until you are familiar with these controls.
4-Way Chute Directional Control (If so Equipped)
Drift Cutters (If so Equipped)
The drift cutters are designed for use in deep snow. Their use
is optional for normal snow conditions. Maneuver the snow
thrower so that the cutters penetrate a high standing snow drift
to assist snow falling into the augers for throwing.
Chute Clean-Out Tool
WARNING! Never use your hands to clear a
clogged chute assembly. Shut off engine and remain
behind handles until all moving parts have stopped
before unclogging.
The chute clean-out tool is conveniently fastened to the rear of
the auger housing with a mounting clip. Should snow and ice
become lodged in the chute assembly during operation, proceed
as follows to safely clean the chute assembly and chute opening:
The chute directional control is located on the left side of the
dash panel.
•
To change the direction in which snow is thrown, squeeze
the button on the joy-stick and pivot the joy-stick to the
right or to the left.
•
To change the angle/distance which snow is thrown, pivot
the joy-stick forward or backward.
Overhead Chute Directional Control (If so Equipped)
The overhead chute directional control is located in the center of
the snow thrower between the handle panel and lower handle.
To change the direction in which snow is thrown, rotate the
chute directional control.
CHUTE DIRECTIONAL CONTROL
DISCHARGE
LEFT
DISCHARGE
RIGHT
1.
Release both the Auger Control and the Drive Control.
2.
Stop the engine. Refer to the Engine Operator’s Manual.
Remove the key.
3.
Remove the clean-out tool from the clip which secures it to
the rear of the auger housing.
4.
Use the shovel-shaped end of the clean-out tool to
dislodge and scoop any snow and ice which has formed in
and near the chute assembly.
5.
Refasten the clean-out tool to the mounting clip on the
rear of the auger housing, reinsert the key and start the
snow thrower’s engine.
While standing in the operator’s position (behind the snow
thrower), engage the auger control for a few seconds to clear any
remaining snow and ice from the chute assembly.
CHUTE TILT
DOWN
CHUTE TILT
UP
Two-Way Chute-Pitch Control™ (If so Equipped)
The two-way chute-pitch control is located on the left side of the
dash panel and is used to control the distance of snow discharge
from the chute.
•
To change the upper chute angle to control the distance
that snow is thrown, pivot the lever forward or backward.
•
Move the lever forward to pivot the upper chute down and
reduce the distance snow is thrown.
•
Move the lever rearward to pivot the upper chute upward
and increase the distance snow is thrown.
Section 4 — Controls and Features
17
5
Operation
Starting and Stopping the Engine
Replacing Shear Pins
Refer to the Engine Operator’s Manual packed with your snow
thrower for instructions on starting and stopping the engine.
The augers are secured to the spiral shaft with shear pins and
cotter pins. If the auger should strike a foreign object or ice jam,
the snow thrower is designed so that the pins may shear. If the
augers will not turn, check to see if the pins have sheared. See
Figure 5-2.
To Engage Drive
1.
With the throttle control in the Fast (rabbit) position, move
shift lever into one of the six forward (F) positions or two
reverse (R) positions. Select a speed appropriate for the
snow conditions and a pace you’re comfortable with.
2.
Squeeze the drive control against the handle the snow
thrower will move. Release it and drive motion will stop.
To Engage Augers
To engage the augers and start throwing snow, squeeze the
auger control against the left handle. Release to stop the augers.
To Steer
With the drive control engaged, squeeze the right steering
trigger control to turn right. Squeeze the left steering trigger
control to turn left.
CAUTION: Operate the snow thrower in open
areas and at slow speeds until you are familiar with
the drive control and comfortable operating the
steering controls.
Engage Heated Grips (If so Equipped)
CAUTION: It is recommended that you wear
gloves when using the heated grip. If the heated
grip become too hot, turn it off.
To activate the heated grips, move the switch found on the rear
of the dash panel into the ON position. See Figure 5-1.
Figure 5-1
18
Figure 5-2
CAUTION: NEVER replace the auger shear pins
with anything other than OEM Part No.738-04124A
replacement shear pins. Any damage to the auger
gearbox or other components as a result of failing to
do so will NOT be covered by your snow thrower’s
warranty.
WARNING! Always turn off the snow thrower’s
engine and remove the key prior to replacing shear
pins.
6
Maintenance & Adjustments
Maintenance
3.
Loosen the rear skid shoe bolts on both sides of the snow
thrower housing and remove the carriage bolts and hex
nuts which attach shave plate to the auger housing.
4.
Slide the shave plate downward into the second position.
Reinstall and tighten all bolts securely. See Figure 6-2.
Engine
Refer to the Engine Operator’s Manual.
Tire Pressure
Refer to Assembly and Set-up section for information regarding
tire pressure.
Shave Plate and Skid Shoes
The shave plate and skid shoes on the bottom of the snow
thrower are subject to wear. They should be checked periodically
and replaced when necessary.
NOTE: The skid shoes on this machine have two wear edges.
When one side wears out, they can be rotated 180° to use the
other edge.
To remove skid shoes:
1.
Remove the four carriage bolts and hex flange nuts which
secure them to the snow thrower.
2.
Rotate and reassemble skid shoes with the four carriage
bolts (two on each side) and hex flange nuts. Refer to
Figure 6-1.
Figure 6-2
To remove shave plate:
1.
Remove the carriage bolts and hex nuts which attach it to
the auger housing.
2.
Reassemble new shave plate, making sure heads of
carriage bolts are to the inside of housing. Tighten securely.
See Figure 6-3.
NOTE: Augers not shown for clarity.
Figure 6-1
NOTE: The shave plate on HD units only has a wear edge that can
be adjusted forward to prolong its life. As the shave plate wears,
it can be moved into a second position.
To move shave plate:
1.
Allow the engine to run until it is out of fuel.
2.
Carefully pivot the snow thrower up and forward so that it
rests on the auger housing.
Figure 6-3
19
Lubrication
Wheels
At least once a season, remove both wheels. Clean and coat the
axles with a multipurpose automotive grease before reinstalling
wheels.
Auger Shaft
At least once a season, remove the shear pins from the auger
shafts. Spray lubricant inside the shafts and around the spacers
and the flange bearings/bushings found at either end of the
shafts. See Figure 6-4.
Figure 6-5
4.
Apply a light coating of Bostik Regular Grade Never-Seez®
to the hex shaft. See Figure 6-6.
Figure 6-4
Gear Shaft
The gear (hex) shaft should be lubricated at least once a season
or after every twenty-five (25) hours of operation.
1.
Allow the engine to run until it is out of fuel.
2.
Carefully pivot the snow thrower up and forward so that it
rests on the auger housing.
3.
Remove the frame cover from the underside of the snow
thrower by removing the self-tapping screws which secure
it. Refer to Figure 6-5.
Figure 6-6
NOTE: When lubricating the hex shaft, be careful not to get
any oil on the aluminum drive plate or the rubber friction
wheel. Doing so will hinder the snow thrower’s drive
system. Wipe off any excess or spilled oil.
Adjustments
Shift Rod (If Equipped)
If the full range of speeds (forward and reverse) cannot be
achieved, adjust the shift rod as follows:
20
Section 6 — Maintenance & Adjustments
1.
Place the shift lever in the fastest forward speed position.
2.
Remove the cotter pin and washer from the adjustment
ferrule on the shift rod and pull it out from the shift lever.
See Figure 6-7.
2.
Loosen the hex nut on the shift cable index bracket. See
Figure 6-9.
3.
Pivot the bracket downward to take up slack in the cable.
4.
Retighten the hex nut.
Figure 6-7
3.
Pivot the shift bracket downward as far as it will go. See
Figure 6-8.
Figure 6-9
Auger Control
Refer to the Assembly and Set-up section for instructions on
adjusting the auger control cable.
Skid Shoes
Refer to the Assembly and Set-up section for instructions on
adjusting the skid shoes.
Drive Control
When the drive control is released and in the disengaged “up”
position, the cable should have very little slack. It should NOT be
tight.
NOTE: If excessive slack is present in the drive cable or if the snow
thrower’s drive is disengaging intermittently during operation,
the cable may be in need of adjustment.
Check the adjustment of the drive control as follows:
Figure 6-8
4.
Rotate the ferrule up or down on the shift rod as necessary
until the ferrule lines up with the upper hole in the shift
lever. Refer to Figure 6-7 inset.
5.
Insert the ferrule into the upper hole and secure with the
washer and cotter pin.
Shift Cable (If Equipped)
If the full range of speeds (forward and reverse) cannot be
achieved, adjust the shift cable as follows:
1.
Place the shift lever in the fastest forward speed position.
1.
With the drive control released, push the snow thrower
gently forward. The unit should roll freely.
2.
Engage the drive control and gently attempt to push the
snow thrower forward. The wheels should not turn. The
unit should not roll freely.
If any of the above tests failed, the drive cable is in need of
adjustment. Proceed as follows:
1.
Shut off the engine as instructed in the separate engine
manual.
2.
Loosen the lower hex screw on the drive cable bracket. See
Figure 6-10.
Section 6 — Maintenance & Adjustments
21
2.
Pull out the chute control rod until the hole in it lines up
with the second hole in the chute rotation assembly.
3.
Reinsert the hairpin clip through this hole and the chute
control rod. See Figure 6-11.
Chute Assembly (Overhead Chute Control) (If so Equipped)
If the chute fails to remain stationary during operation, the
pre-load of the chute can be adjusted by tightening the hex nut
found on the front of the chute control assembly.
To increase the preload, tighten the hex nut clockwise in ¼ turn
intervals. See Figure 6-12.
Figure 6-10
3.
Position the bracket upward to provide more slack (or
downward to increase cable tension).
4.
Retighten the upper hex screw.
5.
Check the adjustment of the drive control as described
above to verify proper adjustment has been achieved as
follows:
a.
With the drive control released, move the shift lever
back and forth between the R2 position and the F6
position several times. There should be no resistance
in the shift lever.
Chute Control Rod (4-Way Chute Control) (If so Equipped)
To adjust the chute control rod, proceed as follows:
1.
Remove the hairpin clip from the hole closest to the chute
assembly on the chute rotation assembly. See Figure 6-11.
Figure 6-12
If the chute directional control is difficult to crank, decrease the
preload by loosening the hex nut counterclockwise in ¼ turn
intervals.
Off-Season Storage
If the snow thrower will not be used for 30 days or longer, follow
the storage instructions below.
1.
Lubricate the machine as instructed earlier in this section.
2.
Store in a clean, dry area.
3.
If storing the snow thrower in an unventilated area,
rustproof the machine using a light oil or silicone to coat
the snow thrower.
4.
Clean the exterior of the engine and the snow thrower.
IMPORTANT: When storing unit or when it is not being
serviced, it is to remain in the operating position with both
wheel and auger housing on the ground.
NOTE: Refer to the Engine Operator’s Manual for information on
storing your engine.
Figure 6-11
22
Section 6 — Maintenance & Adjustments
7
Service
Belt Replacement
3.
Auger Belt
Loosen and remove the two bolts and flat washers securing
the belt guide. See Figure 7-2. Remove belt guide.
To remove and replace your snow thrower’s auger belt, proceed
as follows:
1.
Allow the engine to run until it is out of fuel. Do not
attempt to pour fuel from the engine.
2.
Remove the plastic belt cover on the front of the engine by
removing the two self-tapping screws. See Figure 7-1.
Figure 7-2
4.
Roll the auger belt off the engine pulley. See Figure 7-3.
Figure 7-1
Figure 7-3
23
5.
Carefully pivot the snow thrower up and forward so that it
rests on the auger housing.
6.
Remove the frame cover from the underside of the snow
thrower by removing the self-tapping screws which secure
it. See Figure 7-4.
NOTE: Engaging the auger control will ease removal and
reinstallation of the belt.
Figure 7-6
9.
Figure 7-4
7.
Replace the auger belt by following instructions in reverse
order.
NOTE: Do not forget to reinstall the shoulder bolt and
reconnect the spring to the frame after installing a
replacement auger belt.
Loosen and remove the shoulder bolt which acts as a belt
keeper. See Figure 7-5.
10.
After replacing the auger belt, perform the Auger Control
test on page 11 of the Assembly and Set-Up section.
Drive Belt
NOTE: Special tools are required and several components must
be removed in order to replace the snow thrower’s drive belt. See
your authorized service dealer to have the drive belt replaced or
phone Customer Support as instructed on page 2 for assistance.
Friction Wheel Inspection
If the snow thrower fails to drive with the drive control engaged,
and performing the drive control cable adjustment fails to
correct the problem, the friction wheel may need to be replaced.
NOTE: Special tools are required and several components must
be removed in order to replace the snow thrower’s friction wheel
rubber. See your authorized service dealer to have the friction
wheel rubber replaced or phone Customer Support as instructed
on page 2 for assistance.
To inspect the friction wheel, proceed as follows:
Figure 7-5
8.
24
Remove the belt from around the auger pulley, and slip the
belt between the support bracket and the auger pulley.
See Figure 7-6.
Section 7— Service
1.
Allow the engine to run until it is out of fuel. Do not
attempt to pour fuel from the engine.
2.
Carefully pivot the snow thrower up and forward so that it
rests on the auger housing.
3.
Remove the frame cover from the underside of the snow
thrower by removing four self-tapping screws which secure
it. See Figure 7-4.
4.
Examine the friction wheel for signs of wear or cracking.
8
Troubleshooting
Problem
Engine fails to start
Cause
Remedy
1. Choke not in CHOKE position.
1. Move choke to CHOKE position.
2. Spark plug wire disconnected.
2. Connect wire to spark plug.
3. Fuel tank empty or stale fuel.
3. Fill tank with clean, fresh gasoline.
4. Engine not primed.
4. Prime engine as instructed in the Engine
Operator’s Manual.
5. Faulty spark plug.
5. Clean, adjust gap, or replace.
6. Key not in ignition on engine.
6. Insert key fully into the switch.
7. Extension cord not connected.
7. Connect one end of the extension cord to the
electric starter outlet and the other end to a
three-prong 120-volt, grounded, AC outlet.
1. Engine running on CHOKE.
1. Move choke lever to RUN position.
2. Stale fuel.
2. Fill tank with clean, fresh gasoline.
3. Water or dirt in fuel system.
3. Drain fuel tank. Refill with fresh fuel.
4. Carburetor out of adjustment.
4. Contact an authorized Service Center.
5. Engine over-governed
5. Contact an authorized Service Center.
Engine overheats
1. Carburetor not adjusted properly.
1. Contact an authorized Service Center.
Excessive vibration
1. Loose parts or damaged auger.
1. Stop engine immediately and disconnect spark
plug wire. Tighten all bolts and nuts. If vibration
continues, have unit serviced by an authorized
Service Center.
Loss of power
1. Spark plug wire loose.
1. Connect and tighten spark plug wire.
2. Gas cap vent hole plugged.
2. Remove ice and snow from gas cap. Be certain
vent hole is clear.
1. Drive control cable in need of adjustment.
1. Adjust drive control cable. Refer to Maintenance
& Adjustments section.
2. Drive belt loose or damaged.
2. Replace drive belt. See authorized service dealer.
3. Friction wheel worn.
3. Replace friction wheel. Refer to Service section.
1. Chute assembly clogged.
1. Stop engine immediately and disconnect spark
plug wire. Clean chute assembly and inside of
auger housing with clean-out tool or a stick.
2. Foreign object lodged in auger.
2. Stop engine immediately and disconnect spark
plug wire. Remove object from auger with cleanout tool or a stick.
3. Auger control cable in need of
adjustment.
3. Refer to Auger Control Test.
4. Auger belt loose or damaged.
4. Refer to Maintenance & Adjustments section.
5. Shear pin(s) sheared.
5. Replace with new shear pin(s).
1. Chute assembled incorrectly.
1. Unassemble chute control and reassemble as
directed in the Assembly section.
Engine running erratically/
inconsistent RPM (hunting
or surging)
Unit fails to propel itself
Unit fails to discharge snow
Chute fails to easily rotate
180 degrees
25
9
Replacement Parts
Component
Part Number and Description
954-04195A
954-04201A
Auger Drive Belt
Wheel Drive Belt
684-04153C
935-04054
Friction Wheel Assembly
Friction Wheel Rubber
925-1629
Lamp, 12V
738-04124A
714-04040
Shear Pin, 1.50
Bow-tie Cotter Pin
731-06931
Skid Shoe, Deluxe
931-2643
Chute Clean-out Tool
790-00120
790-00652
790-00121
790-00525
790-00118
790-00549
790-00550
Shave Plate (3X 24)
Shave Plate (3X 24 HD)
Shave Plate (3X 26)
Shave Plate (3X 26 HD)
Shave Plate (3X 28)
Shave Plate (3X 28 HD)
Shave Plate (3X 30 HD)
951-10630Key
951-10292
Spark Plug
Phone (800) 965-4CUB to order replacement parts or a complete Parts Manual (have your full model number and serial number
ready). Parts Manual downloads are also available free of charge at www.cubcadet.com.
26
10
Attachments & Accessories
The following attachments and accessories are available for your Cub Cadet snow thrower. See your Cub Cadet dealer or the retailer
from which you purchased your snow thrower for information regarding price and availability.
Model Number
929-0071A
Description
Extension Cord, 110V
753-05762A
Heated Grips*
OEM-390-679
Drift Cutter Kit
490-241-0032
Snow Cab
490-241-0013
Snow Thrower Auger and Chute Maintenance Kit
490-241-0038
Roller Skid Shoes
490-290-0010
Snow Thrower Cover
490-241-0028
Snow Thrower Tire Chains (16” x 4.8” Tires)
490-241-0029
Snow Thrower Tire Chains (16” x 6.5” Tires)
490-900-0062
Non-Stick Spray
490-240-0011
Fuel Test Swabs
490-850-0008
Siphon Pump
490-000-0028
Carburetor and Choke Cleaner
490-325-0020
32 oz. Tire and Tube Sealant
490-325-0022
16 oz. Tire and Tube Sealant
490-850-0013
Tire/Tube Foot Pump
490-850-0014
Deluxe Tire Plug Kit
22208
8 oz. Fuel Stabilizer
22216
32 oz. Fuel Stabilizer
*Compatible on models equipped with a split alternator.
27
CUB CADET LLC
MANUFACTURER’S LIMITED WARRANTY FOR SNOW THROWERS, LOG SPLITTERS
CHIPPER-SHREDDERS, CHIPPER-SHREDDER VACUUMS AND JET SWEEPS
The limited warranty set forth below is given by Cub Cadet LLC
with respect to new merchandise purchased and used in the United
States, its possessions and territories, and by MTD Products Limited
with respect to new merchandise purchased and used in Canada
and/or its territories and possessions.
a.
Routine maintenance items such as lubricants, filters, blade
sharpening, tune-ups, brake adjustments, clutch adjustments,
deck adjustments, and normal deterioration of the exterior
finish due to use or exposure.
b.
Log splitter pumps, valves, and cylinders have a separate one
year warranty.
c.
Cub Cadet does not extend any warranty for products sold
or exported outside of the United States and/or Canada, and
their respective possessions and territories, except those
sold through Cub Cadet’s authorized channels of export
distribution.
For commercial uses and applications: Cub Cadet warrants this
product (excluding Normal Wear Parts and the Auger Gearbox, as
described below) against defects in material and workmanship for
a period of one (1) year from the date of original retail purchase or
lease.
d.
Replacement parts that are not genuine Cub Cadet parts.
e.
Service completed by someone other than an authorized
service dealer.
f.
Transportation charges and service calls.
“Cub Cadet” will, at its option, repair or replace, free of charge, any
part found to be defective in materials or workmanship. This limited
warranty shall only apply if this product has been operated and
maintained in accordance with the Operator’s Manual furnished
with the product, and has not been subject to misuse, abuse,
neglect, accident, improper maintenance, alteration, vandalism,
theft, fire, water, or damage because of other peril or natural
disaster. Damage resulting from the installation or use of any part,
accessory or attachment not approved by Cub Cadet for use with
the product(s) covered by this manual will void your warranty as to
any resulting damage.
No implied warranty, including any implied warranty of
merchantability of fitness for a particular purpose, applies
after the applicable period of express written warranty above
as to the parts as identified. No other express warranty,
whether written or oral, except as mentioned above, given by
any person or entity, including a dealer or retailer, with respect
to any product, shall bind Cub Cadet. During the period of the
warranty, the exclusive remedy is repair or replacement of the
product as set forth above.
This warranty is in addition to any applicable emissions warranty
provided with your product.
For non-commercial use: Cub Cadet warrants this product
(excluding Normal Wear Parts and the Auger Gearbox, as described
below) against defects in material and workmanship for a period of
three (3) years from the date of original retail purchase or lease.
Normal Wear Parts are warranted to be free from defects in material
and workmanship for a period of thirty (30) days from the date of
purchase. Normal wear parts include, but are not limited to items
such as: belts, skid shoes, shave plates, blades, debris collection
bags, wheels and tires.
Auger Gearbox — Cub Cadet warrants the auger gearbox (on threestage snow thrower models only) against defects in material and
workmanship for a period of five (5) years, commencing on the date
of the snow thrower’s original purchase.
HOW TO OBTAIN SERVICE: Warranty service is available, WITH
PROOF OF PURCHASE, through your local authorized service dealer.
To locate the dealer in your area:
In the U.S.A.
To locate the dealer in your area, check your Yellow Pages, or
contact Cub Cadet LLC at P.O. Box 361131, Cleveland, Ohio 441360019, or call 1-877-282-8684, or log on to our Web site at www.
cubcadet.com.
In Canada
Contact MTD Products Limited, Kitchener, ON N2G 4J1, or call
1-800-668-1238 or log on to our Web site at www.mtdcanada.com.
This limited warranty does not provide coverage in the following
cases:
The provisions as set forth in this warranty provide the sole
and exclusive remedy arising from the sale. Cub Cadet shall
not be liable for incidental or consequential loss or damage
including, without limitation, expenses incurred for substitute
or replacement lawn care services or for rental expenses to
temporarily replace a warranted product.
Some states do not allow the exclusion or limitation of incidental
or consequential damages, or limitations on how long an implied
warranty lasts, so the above exclusions or limitations may not apply
to you.
In no event shall recovery of any kind be greater than the amount
of the purchase price of the product sold. Alteration of safety
features of the product shall void this warranty. You assume the
risk and liability for loss, damage, or injury to you and your property
and/or to others and their property arising out of the misuse or
inability to use the product.
This limited warranty shall not extend to anyone other than the
original purchaser or to the person for whom it was purchased as a
gift.
HOW STATE LAW RELATES TO THIS WARRANTY: This limited
warranty gives you specific legal rights, and you may also have
other rights that vary in different jurisdictions.
IMPORTANT: Owner must present Original Proof of Purchase to
obtain warranty coverage.
Cub Cadet LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019; Phone: 1-877-282-8684
MTD Canada Limited - KITCHENER, ON N2G 4J1; Phone 1-800-668-1238
GDOC-100160 REV. C