Atomic 2907 TBI, ECU, Later Version Instructions
Atomic 2907 is a versatile device designed to enhance your vehicle's performance and fuel efficiency. Here are some of its key capabilities:
-
Real-time engine monitoring: Atomic 2907 provides real-time data on crucial engine parameters, including RPM, MAP, TPS, and IAT, allowing you to stay informed about your vehicle's health and performance.
-
Customizable fuel mapping: The device enables you to create and modify fuel maps to optimize your vehicle's air-fuel ratio for different driving conditions and performance goals.
-
Ignition timing control: Atomic 2907 offers precise ignition timing control, allowing you to adjust timing for optimal engine performance and efficiency.
Advertisement
Advertisement
Atomic ECU Assembly
PN 2906
ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your product and helps the MSD R&D team create new products that you ask for! Go to www.msdperformance.com/registration.
Parts Included:
1 - ECU Assembly
2 - Oval O-rings
1 - Foam gasket
It is best to remove the throttle body from the engine when installing replacement parts.
REMOVAL
• Disconnect the battery (-) cable.
• Remove the Air Cleaner assembly.
• Disconnect the throttle cable assembly, vacuum hoses, electrical connections, and fuel lines from the throttle body. Be prepared to catch fuel when removing fuel lines.
• Caution should be taken when disassembling the throttle body.
Remove the eight bolts that secure the fuel rails from the throttle body (Figure 1).
Disconnect the electrical connectors from the idle air control motor
(IAC), injectors, fuel pressure sensor (FPS), and pull the rails away from the throttle body (Figure 2).
DANGER
(Figure 3). Take caution not to score the machined surfaces.
WARNING
CAUTION
Installation of this product requires detailed knowledge of automotive systems and repair procedures. Installation of fuel system parts and any fuel tank modifications must be carried out by a qualified automotive technician. Installation of fuel system parts requires handling of gasoline. Ensure that work is performed in a well ventilated area with an approved fire extinguisher nearby. Extinguish all open flames, prohibit smoking and eliminate all sources of ignition in the area of the vehicle before beginning the installation.
NOTICE
apparel should be worn to protect against debris and sprayed gasoline. The finished work must be thoroughly checked to ensure there are no fuel leaks.
DISCONNECT
O-RING
Figure 1
Figure 2
Figure 3
M S D • W W W . A T O M I C E F I . C O M • ( 9 1 5 ) 8 5 5 - 7 1 2 3 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4
2 INSTALLATION INSTRUCTIONS
Remove the four screws that hold the ECU (Block with
MSD cast into it) to the throttle body (Figure 4).
Carefully lift the block straight up away from the throttle body. There are four pins and an intake air temperature
(IAT) sensor under the ECU block that can easily be damaged from mishandling (Figure 5). The IAT element sits in a plastic tube that may or may not lift out when the
ECU is removed from the throttle body. Be careful not to lose the IAT tube (Figure 6).
LIFT
ECU OFF
Figure 4
IAT TUBE AND
ELEMENT
Figure 5
IAT TUBE
MAP
SENSOR PINS
IAT ELEMENT
Figure 6
M S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 5 - 7 1 2 3 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4
INSTALLATION INSTRUCTIONS 3
Remove the foam gasket from the throttle body and replace with the supplied gasket. Place the IAC tube into the orifice on the throttle body (Figure 7).
Carefully remove the protective plastic header from the map sensor pins, Figure 8.
Carefully lower the ECU assembly onto the throttle body. Avoid forcing the ECU assembly as the IAT sensor and four pins for the MAP sensor are delicate. Double check the four map sensor pins and
IAT sensor have lined up. Route the wire harnesses in a manner that they do not pinch when the ECU is bolted down (Figure 9).
Assembly of the fuel rails is reverse order of the disassembly Torque specifications for the
ECU and fuel rail bolts is 25-30 in-lb. IAC
TUBE
FOAM GASKET
IAC TUBE
IN ORIFICE
ON THE
THROTTLE
BODY
Figure 7
REMOVE THE
PROTECTIVE HEADER
Figure 8
DO NOT ALLOW
WIRES TO BE
PINCHED
Figure 9
M S D • W W W . A T O M I C E F I . C O M • ( 9 1 5 ) 8 5 5 - 7 1 2 3 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4
TECH NOTES
_________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________
Service
In case of malfunction, this MSD component will be repaired free of charge according to the terms of the warranty.
When returning MSD components for warranty service, Proof of Purchase must be supplied for verification. After the warranty period has expired, repair service is based on a minimum and maximum fee.
All returns must have a Return Material Authorization (RMA) number issued to them before being returned. To obtain an RMA number please contact MSD Customer Service at 1 (888) MSD-7859 or visit our website at www.msdperformance.com/rma to automatically obtain a number and shipping information.
When returning the unit for repair, leave all wires at the length in which you have them installed. Be sure to include a detailed account of any problems experienced, and what components and accessories are installed on the vehicle.
The repaired unit will be returned as soon as possible using Ground shipping methods (ground shipping is covered by warranty). For more information, call MSD at (915) 855-7123. MSD technicians are available from 7:00 a.m. to
5:00 p.m. Monday - Friday (mountain time).
Limited Warranty
M
SD warrants this product to be free from defects in material and workmanship under its intended normal use*, when properly installed and purchased from an authorized MSD dealer, for a period of one year from the date of the original purchase. This warranty is void for any products purchased through auction websites. If found to be defective as mentioned above, it will be repaired or replaced at the option of MSD. Any item that is covered under this warranty will be returned free of charge using Ground shipping methods.
This shall constitute the sole remedy of the purchaser and the sole liability of MSD. To the extent permitted by law, the foregoing is exclusive and in lieu of all other warranties or representation whether expressed or implied, including any implied warranty of merchantability or fitness. In no event shall MSD or its suppliers be liable for special or consequential damages.
*Intended normal use means that this item is being used as was originally intended and for the original application as sold by MSD. Any modifications to this item or if it is used on an application other than what MSD markets the product, the warranty will be void. It is the sole responsibility of the customer to determine that this item will work for the application they are intending. MSD will accept no liability for custom applications.
M S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 5 - 7 1 2 3 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4
32062
© 2014 MSD LLC
Revised Printed

Public link updated
The public link to your chat has been updated.
Advertisement