GMP

ISO9001

ISO14001

ISO13485

CERTIFIED

MEDICAL POWER WHEELCHAIR

Owner’s Manual

ATTENTION

Please read your owner’s manual before driving your power

wheelchair.

STREAMER Sport

888WA

~0~

GMP

ISO9001

ISO14001

ISO13485

CERTIFIED

CONTENTS

INTRODUCTION

page 3

FEATURE GUIDE

page 3

ACCESSORY

page 4

EMI WARNING

page 5 – 6

INSTRUCTIONS

page 7 – 8

INDICATION LABEL LOCATION

page 9

PREPARATION FOR USE

page 10

PROGRAMMABLE CONTROLLER

ADJUSTMENT

page 11 – 12

OPERATION INSTRUCTIONS

page 13 – 14

DISASSEMBLY & ASSEMBLY INSTRUCTIONS

page 15 – 16

BATTERIES & BATTERY CHARGING

page 17 – 20

TROUBLE SHOOTING

page 21 – 22

SPECIFICATION

page 23

DISCLAIMER

page 24

~2~

GMP

ISO9001

ISO14001

ISO13485

CERTIFIED

INTRODUCTION

Congratulations on receiving the STREAMER SPORT Powerchair. This Powerchair is the ultimate combination of style and comfort. The short wheelbase allows easy maneuverability within the smallest spaces both indoors and outdoors. The rear drive wheels and electromagnetic brakes provide a safe and comfortable ride.

This manual contains important information regarding the safe use of the Powerchair.

Please read it carefully before using the Powerchair and make sure you understand all the instructions.

Warning! Please make sure that you are physically fit to operate this unit. Consult your dealer/doctor for advice.

FEATURE GUIDE

STREAMER SPORT (888WA)

(1)

(2)

(3)

(4)

(5)

(6)

(7)

Headrest

(adjustable with selected height)

Backrest

Joystick Controller

Charging Port

Rear Drive Wheel

（

10”）

Front Castor (

6”)

Armrest

(adjustable with selected width, angle and height)

(4)

Zoom View of

Charging Port

(8)

(9)

Captain Seat Assembly

Seat Supporting Post

(10)

Chassis Shroud

(11)

Footrest

(12)

Option

(refer to page 4)

(11)

~3~

(2)

(1)

(3)

Fig. 1

(6)

(9)

(8)

(5)

(7)

(10)

GMP

ISO9001

ISO14001

ISO13485

CERTIFIED

OPTIONAL ACCESSORY

Example

Adjustable

Height

Footrest

Adaptor

Elevating Leg

Rest (6-hole adjustable as standard. 10- hole adjustable with

60mm extension is optional.)

Swing-Away

Joystick Mount

Bracket

Remark: For other available accessories if required, please consult your authorized provider.

~4~

GMP

ISO9001

ISO14001

ISO13485

CERTIFIED

EMI WARNING

ELECTROMAGNETIC INTERFERENCE (EMI) FROM RADIO WAVE SOURCES

Medical Power Wheelchairs (Hereinafter referred to as “Powerchair”) may be susceptible to electromagnetic interference (EMI), which is a kind of interfering electromagnetic energy (EM) emitted from sources such as radio stations, TV stations, amateur radio (HAM) transmitters, two-way radio, and cellular phones. The interference (from radio wave sources) can cause the Powerchair to release its brakes, move by itself, or move in unintended directions. This can also permanently damage the

Powerchair’s control system.

The sources of radiated EMI can be broadly classified into three types:

1. Hand-held portable transceivers (transmitters-receivers) with the antenna mounted directly on the transmitting unit. Examples include: citizens band (CB) radios, “walkie talkie”, security, fire and police transceivers, cellular telephones, and other personal communication devices.

NOTE! Some cellular telephones and similar devices transmit signals while they are ON, even when not being used.

2. Medium-Range mobile transceivers, such as those used in police cars, fire trucks, ambulances, and taxis. These usually have the antenna mounted on the outside of the vehicle.

3. Long-range transmitters and transceivers, such as commercial broadcast transmitters (radio and TV broadcast antenna towers) and amateur (HAM) radios.

NOTE! Other types of hand-held devices, such as cordless phones, laptop computers, AM/FM radios, TV sets, CD players, and cassette players, and small appliances, such as electric shavers and hair dryers, so far as we know, are not likely to cause problems to the Powerchair.

~5~

GMP

ISO9001

ISO14001

ISO13485

CERTIFIED

EMI WARNING

POWERCHAIR ELECTROMAGNETIC INTERFERENCE (EMI)

Because EM energy rapidly becomes more intense as one moves closer to the transmitting antenna (source), the EM fields from hand-held radio sources

(transceivers) are of special concern. It is possible to unintentionally bring high levels of EM energy very close to the Powerchair’s control system while using these devices. This can affect Powerchair movement and braking. Therefore, the warnings listed below are recommended to prevent possible interference with the control system of the Powerchair.

WARNINGS

1. Do not operate hand-held transceivers (transmitters-receivers), such as citizens band (CB) radios, or turn ON personal communication devices, such as cellular phones, while the Powerchair is turned ON.

2. Be aware of nearby transmitters, such as radio or TV stations, and try to avoid close contact.

3. If unintended movement or brake release occurs, turn the Powerchair OFF as soon as it is safe.

4. Be aware that adding accessories or components, or modifying the Powerchair, may make it more susceptible to EMI.

NOTE! There is no easy way to evaluate the overall immunity of the

Powerchair.

5. Report all incidents of unintended movement or braking to the P o w e r c h a i r provider, and note whether there are sources of EMI nearby.

~6~

GMP

ISO9001

ISO14001

ISO13485

CERTIFIED

SAFETY INSTRUCTIONS

Please use your Powerchair often and let it expand your horizons. The more mobility your Powerchair brings, the happier you will be! But, with all things, observing a few rules will ensure safe maneuvering. So please…

(1) Do not drive the Powerchair without reading this instruction manual.

(2) Do not use the joystick in an erratic manner when going up or down an incline.

(3) Do not carry passengers or exceed the maximum user weight (Table 2).

(4) Do not turn off the joystick controller by switching the On / Off Button when moving at speed. This will bring the electromagnetic brakes on immediately and could cause damage to the joystick controller.

(5) Do not drive over uneven or soft terrain.

(6) Do not mount or dismount the Powerchair unless the electromagnetic brakes are engaged and the joystick controller is off.

(7) Do not operate the Powerchair if the unit is in freewheel mode.

(8) Do not use on the road, except when crossing between sidewalks.

(9) Do not sit on the Powerchair when in a vehicle, but transfer to a vehicle seat.

(10) Do not exceed any grade over 8 degrees (14%).

(11) Always stop fully before changing forward or reverse direction.

(12) Always engage a slow speed when going down gradients (move the joystick slowly towards center position to reduce the speed).

(13) Always approach and climb over curbs at slow speed.

(14) Always use the safety belt.

(15) Always keep feet on the footrest while driving.

(16) Always make sure the batteries are fully charged before setting out on a journey.

(17) Always make sure the Allen bolt, hex screws and nuts of the seat adaptor and seat post are securely tightened before driving the Powerchair.

(18) Always charge the Powerchair in a well ventilated area.

~7~

GMP

ISO9001

ISO14001

ISO13485

CERTIFIED

SAFETY INSTRUCTIONS

(19) Whenever a center bolt of the wheel assembly has been loosened, please replace with a specified new bolt from authorized providers and secure with a torque of 240 ± 5 kg-cm together with Loc-tite 271 adhesive (or equivalent).

(20) When proceeding up any incline, please move the seat to the most forward position or if you have the deluxe seat, make sure that it is in the 90 degree

(upright) position.

(21) Do not adjust the programmer or modify the controller and cables without prior written approval from the manufacturer. Otherwise injury and/or damage to the scooter or surrounding property may occur.

(22) Do not modify any parts on the unit without manufacturer’s written approval, or your warranty will be voided and you will be responsible for the modification.

(23) Charge the batteries before using and charge batteries daily after use.

(24) Battery cables must be securely fastened onto battery terminals by the authorized dealer before using the unit. Batteries must be tied down correctly and securely.

(25) Use caution and reduce speed when turning.

(26) Avoid using the powerchair in wet conditions.

(27) The chassis cover must be properly adjusted, placed and attached with the supportive brackets on the base unit by Velcro provided and then check if the circuit breaker is located within the slot hole of the chassis cover to avoid any possible hindrance from its operation and usage.

(28) Do not use the powerchair as a seat in any vehicle.

Remember! Give consideration to pedestrians whenever using the Powerchair.

You are a motorized pedestrian and must observe all rules and regulations of other pedestrians wherever possible.

~8~

GMP

ISO9001

ISO14001

ISO13485

CERTIFIED

INDICATION LABEL LOCATION

To ensure your safety and protect the Powerchair from damage, please read the safety instructions in this manual and familiarize yourself with the labels listed below.

Labels on Chassis Shroud of STREAMER SPORT (888WA)

(Engaged)

(Disengaged)

Drive

Mode

Free-wheel

Mode

Battery Wiring Diagram

Drive

Mode

(Engaged)

(Disengaged)

Free-wheel

Mode

Caution: Before unit is driven, make sure the Brake Levers are in the Engaged position (at the Drive Mode)

Fig. 2

~9~

GMP

ISO9001

ISO14001

ISO13485

CERTIFIED

PREPARATION FOR USE

The Powerchair has many features designed to give the user maximum comfort.

Adjustments can be made to the following parts of the Powerchair:

(1) Footrest angle can be adjusted from 8°~22°.

(2) Armrests can be set at different angles.

(3) Arms can be adjusted in height.

(4) Arms can be adjusted in width.

(5) Joystick controller can be fitted for either right or left hand use (no tools required).

(6) Seat supporting posts with retaining pins can be adjusted in height.

(7) Backrest angle can be slightly adjusted from 90°~102°.

Adjustments should be carried out by a provider/attendant while the user is seated in the Powerchair with the Powerchair turned off (the seat height adjustment is made when the user is not on the seat).

NOTE! Before using the Powerchair for the first time, be sure the batteries have been connected. Charge the Powerchair for at least 6-8 hours prior to first time use.

PROGRAMMABLE CONTROLLER

STREAMER SPORT (888WA) Powerchair has a programmable controller. For more information regarding the programming parameters for the programmable

Powerchair controller please contact your provider.

~10~

GMP

ISO9001

ISO14001

ISO13485

CERTIFIED

ADJUSTMENT PROCEDURES

ARM ADJUSTMENTS (Fig.3)

ANGLE

Pull up on the end of the armrests and they will flip back up allowing easy transfer in and out of the

(3) seat. Under the armrest, there is a bolt and lock nut

(1) that can be adjusted up or down to change the

(1) angle of the armrest.

(2)

Fig. 3

LENGTH (Adjustable Controller Bracket)

Located under the armrest controller bracket is a hand knob (2). By turning counter-clockwise to release, the controller bracket can be extended and reset in position by re-tightening the hand knob.

HEIGHT

The vertical square tube connected with the armrest can be reset to the desired position by re-tightening the hand knob (3) for armrest height adjustment.

WIDTH

Beneath the rear of the seat there are two hand knobs, one on each side. Release the hand knob and slide each arm assembly outward. Re-tighten the hand knob when in the desired position.

~11~

GMP

ISO9001

ISO14001

ISO13485

CERTIFIED

ADJUSTMENT PROCEDURES

JOYSTICK CONVERSION (right to left or left to right)

Loosen the hand knob [Fig.3 (3)] and remove the entire armrest assembly with the joystick attached. Place the armrest assembly on the desired side. Reset in position by re-tightening the hand knobs to complete joystick conversion.

SEAT HEIGHT ADJUSTMENTS (Fig.4)

The seat supporting post under the seat has three height adjustment holes. By tightening the Allen bolt and Nyloc nut in any one of the holes, three heights can be achieved and the seat supporting post can be secured to the power base. The seat tighten with the seat adaptor is secured to supporting post by two hex screws & nuts.

Always make sure the Allen bolt with Nyloc nut and the hex screws with hex nuts are securely tightened before driving the Powerchair.

The installing or setting-up method is described as Fig.4.

Hex Nut

Hex Screw

Hex Nut

Seat Supporting Post

Nyloc Nut

Hex Nut

Allen Bolt

Fig. 4

~12~

GMP

ISO9001

ISO14001

ISO13485

CERTIFIED

OPERATION INSTRUCTIONS

JOYSTICK CONTROLLER (SHARK 40) OVERVIEW

On / Off Button (1)

This button turns the joystick controller (hereinafter referred to as SHARK 40 joystick) on and off. Do not use this button to stop the Powerchair, except in an emergency.

Speed Decrease Button (2)

10

This button decreases the maximum speed.

Speed Increase Button (3)

This button increases the maximum speed.

Horn Button (4)

Fig. 5

This button operates the Powerchair’s horn.

Battery Gauge (5)

This is a 8-segment display, which indicates if the SHARK 40 joystick is switched on and gives the state of charge of the battery.

Maximum Speed Indicator (6)

This is a 5-segment display, which indicates the maximum speed setting selected.

Attendant Control LED (7)

When the Attendant Remote is activated, the ACU LED will light up and remain lit until the attendant switches back to user mode.

Service Indicator LED (8)

The amber Service Indicator LED is dedicated to displaying joystick Flash Codes.

For a list of Flash Codes and what faults they indicate. Refer to Table 1 for more details.

Joystick (9)

This controls the speed and direction of the Powerchair. Push the joystick in the direction you want to go. The further you push it, the faster the speed will be.

Releasing the joystick will automatically engage brakes and stop the Powerchair.

~13~

GMP

ISO9001

ISO14001

ISO13485

CERTIFIED

OPERATION INSTRUCTIONS

Charging Port (10) for Off-Board Charger

Only plug a Shoprider certified charger into this port. This port should not be used as a power supply for any other electrical devices. Disregarding this will void the warranty of the Powerchair.

GETTING READY TO DRIVE

STEP 1 Press the On / Off Button, then the joystick will turn on after the Battery

Gauge blinks for about a second.

STEP 2 Press the Speed Increase / Decrease Button to set up a suitable level that you can maneuver the Powerchair easily.

NOTE! The Powerchair will not move and the Battery Gauge will blink if you push the joystick before or right after you turn the joystick on. To restore the normal operating status, you have to release the joystick immediately back to its center position. If you do not release the joystick within five seconds, the

Battery Gauge will flash rapidly.

The Powerchair must be powered off and then turned back on again.

STEP 3 Push the joystick to control the speed and direction of the Powerchair.

NOTE! Choose an area with plenty of space to ride the Powerchair. Select the low level of the maximum speed setting until you are familiar with the controls.

In a short time you will be in total control and can then increase the speed in steps.

STEP 4 Release the joystick whenever you want to stop the Powerchair.

ENGAGED / DISENGAGED MODE

In the event of a fault or battery failure, the electromagnetic brakes can be disengaged allowing the Powerchair to be pushed. The levers should be switched to the freewheel position according to the indication labels of Fig.2 to set the

Powerchair to the Engaged / Disengaged Mode.

NOTE! Do not use or sit on the Powerchair when either of the brakes is disengaged, or the SHARK 40 joystick will not operate normally.

~14~

GMP

ISO9001

ISO14001

ISO13485

CERTIFIED

DISASSEMBLY & ASSEMBLY INSTRUCTIONS

(3)

(2)

(4)

Fig. 6

COMPONENTS FOR STREAMER SPORT (888WA)

(1) Captain seat assembly with arm assembly.

(2) Chassis shroud.

(3) Chassis assembly.

(4) Batteries.

(5) Charger (Off-Board)

(1)

(5)

~15~

GMP

ISO9001

ISO14001

ISO13485

CERTIFIED

DISASSEMBLY & ASSEMBLY INSTRUCTIONS

DISASSEMBLY PROCEDURES

WARNING! We advise caution when disassembling and lifting items. You must ensure that the person undertaking these actions is able to handle the weight.

STEP 1 Ensure the area where the Powerchair is to be dismantled is spacious.

STEP 2 Disconnect the plug of the SHARK 40 joystick cable.

STEP 3 Unclip two cable ties bound onto the armrest to loosen joystick cable if it’s one piece instead of 2.

STEP 4 The arm assembly can be removed to make the seat assembly lighter to lift. Under the rear of the seat assembly there are two hand knobs.

Release these by turning in a counter-clockwise direction and slide out the arm assembly from each side.

STEP 5 The seat assembly should be folded down for easier lifting.

STEP 6 Loosen the nuts and then hex screws on seat post adaptor.

STEP 7 Lift the seat assembly free of the chassis assembly.

STEP 8 Loosen the nut and then hex screw on seat post. Loosen and remove the seat height Allen bolt and Nyloc nut. Remove the chassis shroud by simply lifting up. You will find the shroud is attached by Velcro tapes on the chassis.

STEP 9 Unclip a cable tie bound onto the seat post receiver of the chassis and then loosen the fastening strap on batteries. Unclip the battery plugs (red and black). The batteries can now, with the help of carrying straps provided, be lifted from chassis.

CAUTION! Care must be taken to slide the plug through the chassis shroud.

To reassemble the Powerchair, reverse the procedures described above.

Plug

Plug

OR

~16~

GMP

ISO9001

ISO14001

ISO13485

CERTIFIED

BATTERIES & BATTERY CHARGING

BATTERIES

The Powerchair is supplied with 2 x 26 Ah sealed lead acid, maintenance free batteries. These are located under the seat in the center of the Powerchair. For easy handling, Velcro or plastic carrying straps may be provided to assist in installation or removal of the batteries. The duration of the batteries can be affected by temperature, terrain and weight of the user. The Battery Gauge is a guide on the remaining charge in the batteries.

The active user will need to charge the batteries after using approximately more than

30% of battery capacity. As an inactive user, only using from once a week to every other day, the recharge point would be at 50% of discharge.

The Battery Gauge is used to indicate power on and provides an estimate of the remaining battery capacity.

Any green LEDs lit indicate will charged batteries.

If only amber and red LEDs are lit, the batteries are moderately charged. Recharge before undertaking a long trip.

If only red LEDs are lit, the batteries are running out of charge. Recharge as soon as possible

Batteries should be kept fully charged at all times. They must not be left in a discharged state if not using the unit for some time. The batteries should be checked once a month and recharged as needed.

Warning!

•

Batteries contain acid and can explode. Always wear eye protection when working near batteries.

•

Always keep battery terminals and clamps clean and free of corrosion.

•

Never alter battery wiring or battery box.

•

Never allow tools to make contact across terminals.

•

Never use batteries or clamps with wing nut terminals, or clamps that exceed terminal post height.

•

Do not smoke or use open flames when battery box lid is open.

•

Only deep cycle, sealed case construction batteries should be used in this device.

~17~

GMP

ISO9001

ISO14001

ISO13485

CERTIFIED

BATTERIES & BATTERY CHARGING

The following table indicates what the gauge will display for any given state.

Notes

All LEDs OFF Power is OFF

All LEDs ON steady

Power is ON Less LEDs imply a reduced battery charge.

Left RED LED is flashing

Battery charge is low

The batteries should be charged as soon as possible

Right to left

“chase”

Left to right

“chase” alternating with steady display

SHARK joystick is being brought out of

Lock mode

SHARK joystick is in programming, inhibit and/or charging mode

To unlock SHARK joystick, press the Horn button twice within 10 seconds.

The steady LEDs indicate the current state of battery charge.

Alll LEDs flashing slowly

Amber LEDs

SHARK joystick has detected an Out Of

Neutral At Power

Up (OONAPU) condition

Release the joystick back to neutral. fault exists between the power module and remote

Check the power module for a fault, the cable for damage, and that the battery is sufficiently charged.

~18~

GMP

ISO9001

ISO14001

ISO13485

CERTIFIED

BATTERIES & BATTERY CHARGING

BATTERY CHARGING (UNITS EQUIPPED WITH OFF-BOARD CHARGER)

Familiarize yourself with the safety information below prior to using the battery charger.

SAFETY INFORMATION

1. Read the battery charger instructions in this manual and in the manual supplied with the charger prior to charging the batteries.

2. Do not remove the grounding prong from the plug. Removal of the grounding prong could result in an electrical hazard.

3. Only plug the charger into a 3-pronged electrical outlet, or an approved

3-pronged adapter for use with a 2 pronged electrical outlet.

4. Make sure that the wall outlet being used is not controlled by a wall switch that can be easily turned off.

5. Do not use an extension cord to plug in the charger.

6. Do not leave the charger plugged into the charger port if the charger is not charging the unit.

7. Use only the off-board charger supplied with this unit. Never use an automotive type battery charger. Contact your supplier if a replacement off-board charger is needed.

8. Inspect the battery charger, wiring and connections for damage prior to each use.

9. Do not open the battery charger case.

10. The battery charger is supplied with cooling slots. Do not insert objects through the slots.

11. Make sure that the charger is not in contact with inflammable materials at any time.

12. The off-board charger is for indoor use only.

13. Explosive gases may be generated while charging the batteries. Keep the power chair and battery charger away from sources of ignition such as flames or sparks and provide adequate ventilation when charging the batteries.

14. Do not allow children to play near the power chair while the batteries are charging. It is also recommended that the batteries not be charged while the power chair is occupied.

~19~

GMP

ISO9001

ISO14001

ISO13485

CERTIFIED

BATTERIES & BATTERY CHARGING

CHARGING INSTRUCTIONS

1. Connect the charger to the charging port at the front of the SHARK 40 joystick

(item 8 in Fig.5)

2. Plug the charger into the wall outlet.

3. The charging process will start automatically.

CHARGER INDICATION LIGHTS

Blinking Green – Power on at stand-by mode,

Steady Orange – Battery charging,

Steady Green – Charging complete.

Please refer to the LED indicator description based on charging status of the charger.

BATTERY INFORMATION

1. Make sure to use two batteries of the exact same chemistry, amp hours, and capacity.

2. Fully recharge new batteries prior to initial use.

3. It is recommended that the batteries be charged for 8 to 14 hours after daily use.

4. If the power chair is used infrequently (Once a week or less) the batteries will need to be charged once a week for 12 to 14 hours.

5. Do not charge the batteries for more than 24 hours at a charging cycle.

6. Batteries that go below a minimum voltage due to not being charged will be unable to be re-charged.

7. If you do not plan on using your power chair for an extended period it is recommended that you fully charge the batteries and then disconnect the battery harness prior to storage. Store the power chair in a warm dry environment. Never store the batteries where extreme temperatures are possible. Never attempt to charge a frozen battery. A cold or frozen battery should be warmed for several days prior to charging.

~20~

GMP

ISO9001

ISO14001

ISO13485

CERTIFIED

TROUBLE SHOOTING

The Self-Help Guide (Table 1) is intended to assist in the location of a fault that may occur in a certain part of the Powerchair. Flash codes indicate the nature of an abnormal condition directly from the

SHARK joystick Information Gauge. Without the use of any servicing tools, the condition can be simply diagnosed.

If after checking out the fault from the table below and the fault is still showing, do not use the Powerchair. Turn off the power and consult your provider immediately.

Table 1

Flash

Code

Description

Possible stall timeout or user error.

Release the joystick to neutral and try again.

Check the batteries and cabling.

Try charging the batteries.

Batteries may require replacing.

3 Left Motor Fault Check the left motor connections and cabling.

4 Right Motor Fault Check the right motor connections and cabling.

5 Left Park Brake Fault Check the park brake connections and cabling.

6 Right Park Brake Fault Check the park brake connections and cabling.

8

9

SHARK Power Module

Fault

Fault

Check the SHARK Communications Cable.

Replace the Remote.

Check the SHARK joystick connections and wiring.

Replace the Power Module.

SHARK

Communications Fault

Check for possible low battery.

Check the SHARK joystick connections and wiring.

Check for worn motor brushes.

Replace the Remote.

Check all connections and wiring.

Consult a service agent.

11 Incompatible Remote Wrong type of Remote connected.

~21~

GMP

ISO9001

ISO14001

ISO13485

CERTIFIED

TROUBLE SHOOTING

LOCK MODE: The SHARK 40 joystick can be locked to prevent unauthorized use.

The locking method is achieved through a sequence of key presses and joystick movements, as detailed below.

To lock Powerchair controller:

ƒ

While the power is ON, press and hold the Power button for 4 seconds.

ƒ This display will turn off immediately.

ƒ After 4 seconds all LED’s will flash briefly and the horn will sound a short beep.

ƒ The Powerchair will then turn off.

To unlock the Powerchair controller:

ƒ While the SHARK joystick is locked, press the Power button to turn SHARK joystick on.

ƒ All LED’s will flash briefly. The Battery Gauge LED’s will them perform a slow right-to-left chase.

ƒ Press the Horn button twice before the countdown is completed

(approximately 10 seconds).

ƒ This current state-of-charge will then be displayed and SHARK joystick may be operated normally.

SLEEP MODE: After a certain amount of time with no joystick movement, the joystick will automatically turn itself off. Sleep mode will not be entered while programming. When Wakeup style has been set to

“Joystick and Button”, pressing ANY button ONLY will bring the system out of sleep mode.

~22~

GMP

ISO9001

ISO14001

ISO13485

CERTIFIED

SPECIFICATION

Table 2

Overall Length

1

Overall Width

Overall Height

Total Weight (w/ 26 Ah Batteries)

Battery Weight

Battery Capacity

Safe Climbing Angle

Inches

Inches

Lbs

Lbs*pcs

12V_Ah x 2pcs

°

(%)

26”

40”

160

17 lbs*2

26Ah

8(14)

Suggested User Weight (on level surface) Lbs Max. 300

Maximum Speed

3

mph 5

Range

4

(Per charge w/ standard 26 Ah battery)

Miles 8

Charger Type On / Off Board Off Board 24V, 5A

All specifications are subject to change without prior notice. SHOPRIDER

®

/ PIHSIANG

®

reserves the rights of any changes on the unit.

1. Includes the anti-tip wheel.

2. The actual driving range varies with the factors shown below.

(1) the weight of occupant

(2) ground surface

(3) battery capacity and conditions

(4) type of charger

(5) ambient temperature

(6) Driving methods

(7) If the battery and mechanical moving parts fully broken in.

~23~

GMP

ISO9001

ISO14001

ISO13485

CERTIFIED

DISCLAIMER

Congratulations on receiving the STREAMER SPORT Powerchair.

This Powerchair is not intended to be used by individuals with physical limitations that could prevent the user from operating the Powerchair safely. SHOPRIDER

®

disclaims all responsibility for any personal injury or property damage, which may occur as a result of improper or unsafe use of its products. Mechanical or electrical defects will be dealt with on a contingency liability basis.

Warranty is only valid when genuine SHOPRIDER

®

parts are used. All modifications on the Powerchair, unless approved and authorized by SHOPRIDER

®

will automatically invalidate the warranties. Standard warranty does not extend to consumable items and parties other than the original user.

The preceding guidelines are intended to assist you in the safe operation of this

Powerchair. If you should have any questions about the correct operation of the

Powerchair, please contact your authorized SHOPRIDER

®

provider.

Provider Stamp

.

Serial No.:

SHOPRIDER MOBILITY PRODUCTS, INC

21184 S. FIGUEROA ST

CARSON, CA 90745

800-743-0772

P/N: 300904-57-A6C

© Copyright PIHSIANG MACHINERY MFG. CO., LTD. 2003. All rights Reserved. SHOPRIDER

®

/ PIHSIANG

®

are registered trademarks of PIHSIANG

MACHINERY MFG. CO., LTD.

~24~