Yamaha CDR200t User manual
Yamaha CDR200t is a CD-R/RW drive that can read and write CD-R and CD-RW discs. It has a built-in SCSI interface, and it can be used with both IBM-PC and Macintosh computers. The drive supports a variety of recording formats, including CD-ROM, CD-ROM XA, CD-I, CD-DA, CD-Bridge (multisession), CD-Extra, and Video CD. It can also record and play back audio CDs. The drive is easy to install and use, and it comes with a one-year warranty.
advertisement
CDR200t
SERIES
User Guide
Guide de I’utilisateur
Bedienungsanleitung
6
READ
2
WRITE
VOL
Recordable
ON/
DISC
READ/
WRITE
COMPLIANCE INFORMATION STATEMENT
(DECLARATION OF CONFORMITY PROCEDURE)
Responsible Party: Yamaha Systems Technology, Inc.
Address: 100 Century Center Court
San Jose, California 95112
Telephone: (408) 467-2330
FAX: (408) 437-8791
Type of Equipment: CD Recorder
Model Name: CDR200t
CDR200t-NB
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received including interference that may cause undesired operation.
See user manual instructions if interference to radio reception is suspected.
FCC INFORMATION (U.S.A.)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/ s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA.
3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the product “OFF” and “ON”, please try to eliminate the problem by using one of the following measures:
Relocate either this product or the device that is being affected by the interference.
Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the leadin to coaxial type cable.
If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Systems Technology, Inc. 100 Century Center
Court, San Jose, CA95112, U.S.A.
• This manual applies to the CDR200t and CDR200t-NB.
The CDR200t front panel displays the YAMAHA brand name.
The CDR200t-NB front panel does not display a brand name.
Laser Diode Properties
Material : GaAlAs
Wavelength : 780-790 nm
Emission Duration : Continuous
Laser Output Power : Less than 44.6
µ
W*
* T his output is value measured at a distance 200mm from the objective lens surface on the optical pick-up block.
ANSI Class : Class 1
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
CLASS 1 LASER PRODUCT
LASER KLASSE 1 PRODUKT
This compact disc player is classified as a CLASS 1
LASER product.
The CLASS 1 LASER
PRODUCT label must be located on the exterior.
VORSICHT : UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG
GEOFFNET. NICHT DEM STRAHL AUSSETZEN.
VARNING : OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH
SPÄRREN ÄR URKOPPLAD. BETRAKTA EJ STRÅLEN ÄR FARLIG.
VARO! : AVATAESSA JA SUOJALUKITUS OHITETTAESSA OLET
ALTTINA NÄKYMÄTTÖMÄLLE LASERS TEILYLLE. ÄLÄ KATSO SÄTESSEN.
ADVARSEL : USYNLIG LASERSTRALNING VED ÅBNING NÄR SIKKERHETSAF-
BYDERE ER UDE AF FUNKTION. UNDGÅ UDSETTELS FOR STRÅLING.
Varningsanvisning för laserstrålning.
WARNING
❢
WARNING
❢
• The temperature where CDR200t is located should be between 5ºC and 40ºC (41ºF –
104ºF), when used in a fan-cooled system.
• Do not disassemble the CDR200t cover to reduce the risk of electric shock.
• Always remove the disc before transporting
CDR200t.
i
Important Precautions
Important Precautions
Please read the following precautions before attempting to operate CDR200t.
• Before recording a disc, be sure to clean the disc and CDR tray using an air aerosol-type dust remover.
A dust particle on the disc may cause recording to fail, producing an unuseable disc.
• Always record in a dust-free environment. If the disc must be removed from CDR200t before recording is finished, store the disc in a clean, dust-free environment.
• CDR200t contains no user serviceable parts.
Refer all servicing to qualified personnel.
• If any of the following should occur, CDR200t should be serviced by qualified personnel:
Metal objects or liquids get inside CDR200t.
CDR200t does not operate normally or a marked change in performance is noticed.
• Do not place heavy objects on the CD-R discs.
• Do not subject CDR200t and computer to impact or shock when in use, as this may impair recording or playback.
• Yamaha is not responsible for any data or information losses resulting from the operation of
CDR200t.
ii
Table of Contents
Table of Contents
............................................................................. 1
CDR200t Features ......................................................... 1
Orange Book Compatible Recording ............................ 2
Chapter 1 - System Configuration
..................................... 3
For an IBM-PC computer with DOS or Windows ........ 3
For a Macintosh computer ............................................. 3
About Discs ................................................................... 4
Chapter 2 - Installing the Yamaha CDR200t Drive
......... 5
CDR200t drive settings ................................................. 5
Cable Connection .......................................................... 8
.......................................................... 10
Front Panel................................................................... 10
Loading a Disc............................................................. 11
Ejecting the Disc.......................................................... 12
................................................................... 13
Appendix ................................................................................. 14
Specifications............................................................... 14
Front Panel Indicator Key............................................ 15
©1996 Yamaha Corporation. All Rights Reserved.
MS-DOS and Windows are registered trademarks of Microsoft, Inc.
Macintosh is a registered trademark of Apple Computer, inc.
Unix is a registered trademark of UNIX System Laboratories.
All other trademarks are the property of their respective companies.
iii
Introduction
Introduction
Thank you for purchasing a Yamaha CDR200t drive. Please read this manual before using the drive in order to make the best use of the superior CDR200t functions. After reading, please retain this manual for future reference.
CDR200t Features
■ 2xS Recording - 6xS Reading
The CDR200t is a CD-ROM recorder capable of recording at double speed (2xS), or normal speed (1xS). It can read discs at up to 6xS.
■ Compatible with Seven Different Formats
The CDR200t can both record and read seven different formats: CD-
ROM, CD-ROM XA, CD-I, CD-DA, CD-Bridge (multisession), CD-
Extra, and Video CD. The CDR200t is also equipped with an analog audio output terminal (headphones) for CD-DA.
■ SCSI 2 for High-Volume, High-Speed Data Transfer
The CDR200t features SCSI 2, the second generation SCSI interface for connecting computers and peripheral devices. SCSI 2 provides high-speed transmission of large quantities of data, which is especially important when working with image data.
■ Compatible with Windows 95 Plug and Play
SCSI IDs are set automatically by the SCAM protocol (level 1).
■ Orange Book Part 2 Compatible 5-Mode Recording
The CDR200t conforms to the five recording modes outlined in the
Orange Book Part 2: Track at Once, Multisession, Disc at Once, Session at Once, and Packet Writing.
1
Introduction
Orange Book Compatible Recording
Track at Once
In this mode, data can be recorded to disc one track at a time. Discs recorded in this mode cannot be played in CD players or CD-ROM drives other than the CD-R drive until the session is closed.
Multisession
In this mode, data can be recorded to disc in stages (one session at a time).
Additional data can be written later.
Disc at Once
In this mode, data can be recorded to an entire disc in one pass.
It is not possible to write additional data later.
Session at Once
In this mode, data can be recorded to disc one session at a time. To use this mode, your software must support Session at Once recording.
New sessions can be written later.
Packet Writing
This is useful for data back-up. Smaller units of data can be added to tracks. To use this mode, your software must support Packet Writing.
2
Chapter 1 - System Configuration
Chapter 1 - System Configuration
In order to use the CDR200t, you will require the following.
For an IBM-PC computer with DOS or Windows
The following operating environment is required:
• An IBM/AT or compatible PC with a 486/33MHz or better CPU
• A vacant slot in which to install a SCSI card or a pre-installed
SCSI card
• A vacant half-height bay
• Windows 3.1 or later, or Windows 95
• Sufficient hard disk space
Note: You will need about twice as much space on your hard disk as that required by the data you wish to write to CD-ROM.
SCSI card and software
This is required in order to connect a SCSI device (the Yamaha
CDR200t) to your computer.
We recommend the following:
Adaptec SCSI cards: AHA-2940 (PCI), AHA-284x (VL), AHA-2740
(EISA), AHA-154x (ISA), etc.
Yamaha CDR200t is a “SCSI” device. You will need to install a SCSI card and some mastering (writing) software in your host computer to connect the CDR200t.
For a Macintosh computer
The following operating environment is required:
• A Macintosh computer that is equipped with a CPU of 68040 or higher
3
Chapter 1 - System Configuration
About Discs
CD-R Discs
On the CDR200t, you can use conventional CD-R discs that conform to the Recordable Compact Disc Systems Part II (Orange Book).
Yamaha recommends the following Yamaha CD-R discs:
> CDM12Y63
> CDM12Y74 (
(
φ
φ
120mm, 63 minutes)
> CDM12Y74M (
φ
120mm, 74 minutes)
> CDM12Y74T (
φ
120mm, 74 minutes)
120mm, 74 minutes)
Read-only Discs
You can use discs with the logo which conform to the Compact
Disc Read Only Memory standard (CD-ROM standard, Yellow
Book). If you wish to use the audio functions, use discs with the logo, which conform to the Compact Disc Digital Audio standard
(Red Book).
4
Chapter 2 - Installing the Yamaha CDR200t Drive
Chapter 2 - Installing the Yamaha CDR200t Drive
CDR200t drive settings
Before installing the CDR drive into your computer, you will need to set the following jumpers. You set these jumpers by inserting jumper connectors into the jumper switch located on the rear panel of the
CDR drive switch.
♦
♦
♦
♦
SCSI ID settings
Parity setting
Terminator setting
Block size setting
Important: Use long-nose pliers to remove or insert jumper connectors.
Rear Panel
AUDIO OUT
R G L
1 2 4
ID SELECT
PARITY
TERMINATOR
BLOCK SIZE
SER. NO.
SCSI INTERFACE CONNECTOR
1
DC INPUT
+5V G +12V
Jumper Switch
PIN 1
PIN 2
OUT
G L
1 2 4
ID SELECT
PARITY
TERMINATOR
BLOCK SIZE
SCSI IN
PIN 11
PIN 12
5
Chapter 2 - Installing the Yamaha CDR200t Drive
♦ SCSI ID settings
The SCSI ID number is used so that the computer will recognize a connected SCSI device. You can assign 0 through 7 as the SCSI ID number. Usually, “7” is reserved for the SCSI card ID number, and
“0” is reserved for the first SCSI device in the chain. Use a number between 1 and 6 for the CDR200t. Refer to the diagram below for more information on setting the SCSI ID number. The factory set ID number is “3”.
Important: If you are using other SCSI devices, be sure to use a unique ID number for each device.
Note: When you are using Windows 95, and if the SCSI ID setting on the rear panel is the same as the number assigned to another SCSI device, the Plug and Play component of Windows 95 will automatically assign an unused number to the CDR200t (SCAM protocol level 1).
1 2 4 1 2 4 1 2 4 1 2 4
SCSI ID 0 SCSI ID 1 SCSI ID 2 SCSI ID 3
1 2 4 1 2 4 1 2 4 1 2 4
SCSI ID
0
1
2
3
6
7
4
5
SCSI ID 4 SCSI ID 5 SCSI ID 6 SCSI ID 7
SCSI ID Setting
ID 1
0 (OPEN)
1 (SHORT)
0 (OPEN)
1 (SHORT)
0 (OPEN)
1 (SHORT)
0 (OPEN)
1 (SHORT)
ID 2
0 (OPEN)
0 (OPEN)
1 (SHORT)
1 (SHORT)
0 (OPEN)
0 (OPEN)
1 (SHORT)
1 (SHORT)
ID 4
0 (OPEN)
0 (OPEN)
0 (OPEN)
0 (OPEN)
1 (SHORT)
1 (SHORT)
1 (SHORT)
1 (SHORT)
6
Chapter 2 - Installing the Yamaha CDR200t Drive
♦ Parity setting
Parity ON (with a jumper)
— Parity Check will be performed. Normally, use this setting.
Parity OFF (without a jumper)
— Parity Check will not be performed.
Parity ON
1 2 4
ID SELECT
PARITY
TERMINATOR
BLOCK SIZE
Parity OFF
1 2 4
ID SELECT
PARITY
TERMINATOR
BLOCK SIZE
♦ Terminator setting
The terminator setting indicates whether or not this device is the last connected SCSI device.
Terminator ON (with a jumper)
— Use this setting if the CDR200t is the last device in the internal
SCSI daisy-chain.
Terminator OFF (without a jumper)
— Use this setting if devices other than the CDR200t are in the internal SCSI daisy-chain and the CDR200t is not the last device.
Terminator ON
1 2 4
ID SELECT
PARITY
TERMINATOR
BLOCK SIZE
Terminator OFF
1 2 4
ID SELECT
PARITY
TERMINATOR
BLOCK SIZE
7
Chapter 2 - Installing the Yamaha CDR200t Drive
♦ Block size setting
Block size ON (with a jumper)
— Block Size is set to 512Byte/sector. This function is valid only for workstations, such as those that run UNIX.
Block size OFF (without a jumper)
— Normally, use this setting.
Block Size ON
1 2 4
ID SELECT
PARITY
TERMINATOR
BLOCK SIZE
Block Size OFF
1 2 4
ID SELECT
PARITY
TERMINATOR
BLOCK SIZE
Cable Connection
SCSI cable
Connect a SCSI cable to the SCSI INTERFACE CONNECTOR on the rear panel of the CDR200t.
At this time, make sure that figure “1” on upper right corner of the connector will match the red line on the SCSI cable.
AUDIO OUT 1 2 4
L
R G
SER. NO.
ID SELECT
PARITY
TERMINATOR
SCSI INTERFACE CONNECTOR
1
DC INPUT
+5V G +12V
8
Chapter 2 - Installing the Yamaha CDR200t Drive
Audio output cable
Connect an audio output cable to the AUDIO OUT connector in the lower left corner of the rear panel.
Make sure that the projection of the connector is facing upward.
AUDIO OUT 1 2 4
L
R G
ID SELECT
PARITY
TERMINATOR
SER. NO.
1
DC INPUT
+5V G +12V
DC power cable
Connect a DC power cable to the DC INPUT connector on the lower right corner of the rear panel.
Make sure that the notch on the connector is facing upward .
AUDIO OUT 1 2 4
L
R G
ID SELECT
PARITY
TERMINATOR
SER. NO.
1
DC INPUT
+5V G +12V
9
Chapter 3 - Operation
Chapter 3 - Operation
Front Panel
1 6
6
2
READ
WRITE VOL
Recordable
ON/
DISC
READ/
WRITE
2 3 4 5
1 Disc tray
The disc is inserted and ejected here. Pressing the eject button will open the tray.
2 Headphone jack
This stereo mini jack allows you to connect headphones and listen to audio.
3 Headphone volume control
This control adjusts the volume level of the headphone output. Rotating the control clockwise will increase the volume level.
4 ON/DISC LED
This indicator lights up in orange when the CDR200t is powered on, and lights up in green when the CDR200t contains a disc.
5 READ/WRITE LED
This indicator lights up in green when data is being read, and flashes when data is being accessed. It also lights up in orange when data is being recorded on a disc.
6 Eject button
This button is used to open or close the tray.
10
Chapter 3 - Operation
Loading a Disc
1. Press the eject button to open the tray.
2. Carefully place the disc, label-side up, on the disc tray.
3. Press the disc tray softly or press the eject button again to close the disc tray.
6 2
VOL
Recordable
ON/
DISC
READ/
WRITE
11
Chapter 3 - Operation
Ejecting the Disc
If the CDR200t is powered on:
Press the eject button to eject the disc.
Note: You cannot eject the disc if the SCSI command prohibits the eject operation while the CDR200t is reading data.
Caution: Be sure to remove the disc after it is completely ejected. (Trying to remove the disc before it is completely ejected may cause the drive to malfunction.)
6 2
VOL
Recordable
ON/
DISC
READ/
WRITE
Press the eject button
If the CDR200t is not powered on:
Pressing the eject button will not eject the disc.
12
Troubleshooting
Troubleshooting
If CDR200t is not performing as expected, look up the symptoms in the following table, then see what to do.
Symptoms
The power to the CDR200t is off
The power to the computer is off
What to Do
• Check the DC power cable connection.
• Check to see if the SCSI card is correctly installed.
• Check the SCSI cable connection.
The CDR200t is not recognized by the computer.
• Make sure that SCSI ID numbers are assigned exclusively.
The CDR200t does not operate correctly
The disc tray will not open
• Make sure that the last device in the SCSI daisy chain is terminated correctly.
• Install the SCSI driver software again.
The disc ejects
• Make sure that the power to the drive is turned on.
• Make sure that the disc is seated in the tray correctly.
Incorrect operation • Make sure that the disc is seated in the tray correctly.
• Make sure that you are using the correct disc.
• Make sure that there is no dust, dirt, or condensation on the disc or tray.
13
Appendix
Specifications
Interface
Data Capacity
Record/Read Speed
Data Transfer Rate
Burst Transfer Rate
Buffer Size
Access Speed
Installation
Disc Loading
Audio Out
(normal speed)
Power Consumption
Power Supply
Environment
SCSI 2
1.2m/sec: 666MB
1.4m/sec: 540MB
1xS (real-time), 2xS, 4xS (read), 6xS (read)
6xS: 900KB/sec
4xS: 600KB/sec
2xS: 300KB/sec
1xS: 150KB/sec
4.2MB/sec (record asynchronous)
3.4MB/sec (read asynchronous)
1MB (250 sectors)
250ms
Horizontal<
±
15 degrees
Disc tray
Frequency Response 20 - 20,000Hz (Line Out)
Output Level 1 Vrms (Line Out)
11W max (read/write)
5V
±
5%, 12V
±
10%
Temperature: +5
°
C - +40
°
C (read/write, when used in a fan-cooled system)
Humidity: 25 - 80%
146 x 41.3 x 203 mm
1.3kg
Dimensions (WxHxD)
Weight
Rear Panel
SCSI2/Power Supply
ID Selector
Audio Out
Connector
Non-shielded two-in-one, 50p + 4p
Short-pin 12p
MOLEX 53532-04
Specifications are subject to change without prior notice.
14
Front Panel Indicator Key
● on: green
❍ on: orange
✦ flashing: green
✧ flashing: orange
— off
Status
Reset
Ready (no disc)
Inserting disc
Ejecting disc
Ready (disc inserted)
Seeking
Preparing to write
Writing
Writing (test mode)
Playback
Error occurred
ON/DISC
●
●
●
●
—
❍
✧
✦
●
●
✧
Read/Write
—
—
—
—
—
✦
✧
❍
✧
●
—
Appendix
15
VY75970-1
YAMAHA CORPORATION
Electronic Systems Division
advertisement
Key Features
- Reads and writes CD-R and CD-RW discs
- Built-in SCSI interface
- Supports a variety of recording formats
- Can record and play back audio CDs
- Easy to install and use
- One-year warranty