Canon | PIXMA MP600 | Start Here

Start Here
Easy Setup Instructions
Unpack the Machine
Photo All-in-One
• Please confirm the included items against the illustration printed on the lid of the packing box.
• A USB cable is necessary to connect the machine with your computer.
QT5-0683-V02
1 Prepare the Machine
a Place the machine on a flat and
horizontal surface, and do not place
any objects in front of the machine.
Open the Sheet Feeder Cover and
pull the Paper Support, then the Paper
Output Tray and open the Output Tray
Extension.
Caution
Before turning on the machine, remove all of the
shipping tapes.
Important
Do not connect the USB cable until after the software is installed.
Note
To open the Paper Output Tray, put your finger in the
rounded indent of the tray and open it gently.
d Use the { or } button on the
Operation Panel to select the language
for the LCD, then press the OK button.
2 Install the Print Head
3 Install the Ink Tanks
4 Align the Print Head
a Remove the Print Head from its
a Peel back the orange tab completely
a Pinch the Paper Guide and slide it to
package.
the left end.
Paper Support
Extension
(1) Press the { or }
button to select the
language.
Caution
There may be some transparent or light blue ink
on the inside of the bag the print head comes in,
or the inside of the protective cap - this has no
effect on print quality. Be careful not to get ink on
yourself when handling these items.
(2) Press the OK
button.
Important
If an unintended language is displayed on the
LCD, press the Back button to return to the Language selection screen.
b Remove the orange protective cap from
machine and connect the other end to
the wall outlet.
Paper Guide
b Twist off and discard the orange
protective cap located on the bottom of
the ink tank.
Do not press!
Protective Cap
Ink Port
Electrical Contacts
b Load a sheet of letter- or A4-sized
Electrical Contacts
Important
• Do not touch the electrical contacts.
• Do not touch the ink port.
e Open the Scanning Unit (Printer Cover)
until it locks into place. The Print Head
Holder moves to the center.
If the orange-colored protective film is not removed
completely, problems with printing may occur.
the Print Head and discard it.
Once the message “Install the print head and
set the ink tank.” appears, go to e.
b Plug the power cord in the back of the
and remove the plastic wrapper from
the ink tank.
Hardware setup and Print Head
alignment is complete.
Protective Cap
Print Head Nozzles
Note
Do not touch the print head nozzles or the electrical
contacts.
c Insert the ink tank into the right-hand
slot and press the
mark on the ink
tank until it clicks into place.
blank paper in the Auto Sheet Feeder,
align the paper with the right side of
the Cover Guide, then slide the Paper
Guide against the paper stack.
Paper Guide
Print Side
c Firmly raise the Print Head Lock Lever
until it stops.The Print Head Lock Lever
may feel heavy.
Cover Guide
Scanning Unit (Printer Cover)
Easy-Scroll Wheel
Important
Make sure that the Document Cover is closed.
Turn the Easy-Scroll Wheel
left or right to easily select
a menu or a setting item.
For details, refer to “Basic
Operation for the Operation
Panel” in the Quick Start
Guide.
c Make sure that Yes is selected in the
c Open the Operation Panel, then press
the ON/OFF button to turn on the
machine.
d Insert the Print Head.
Important
For your safety, always firmly grip the areas illustrated when opening the Scanning Unit (Printer
Cover).
message requesting head alignment,
then press the OK button.
Refer to the color
guide on the Print
Head Lock Lever.
* You can also use the {,
}, [, or ] button to
select.
Do not touch!
f Open the Inner Cover. Write down
the serial number located inside the
machine. You will need this to register
your product.
d Make sure the ink lamp lights red.
e Lower the Print Head Lock Lever
carefully.
e Close the Inner Cover and the
Scanning Unit (Printer Cover).
Note
Print Head alignment takes about 6 minutes to
complete. Do not start another operation here.
The pattern is printed. And Print Head is aligned
automatically.
OK
Inner Cover
Serial Number Location
Important
If the Scanning Unit (Printer Cover) is left open
for more than 10 minutes, the Print Head Holder
moves to the right. Close and reopen the Scanning
Unit (Printer Cover) to return the Holder to the
center.
Cassette
For information on how to load paper in the
Cassette, refer to “Loading Paper in the
Cassette” in “Loading Printing Paper” of the
Quick Start Guide.
Important
• For your safety, always firmly grip the areas illustrated when closing the Scanning Unit (Printer
Cover).
• The machine starts operating. Wait about 2 minutes until the machine stops making noise.
Note
• The pattern is printed in black and blue.
• When Automatic Print Head Alignment cannot be
executed correctly, the message “Auto head align
has failed.” is displayed on the LCD. Refer to “Error
Message is Displayed on the LCD” in the User’s
Guide on-screen manual.
Macintosh® MP Drivers Installation
M
ac
W
in
in
do
w
s
to
sh
Windows® MP Drivers Installation
Note
• The screens below refer to Windows XP Service Pack 2 installation.
Screens may vary depending on the operating system you are using.
• For Windows XP or Windows 2000, log on to Windows as a member of the
Administrators group before continuing.
• Before installing the driver, disable all anti-virus programs and automatically
loading programs.
a Turn off the machine.
(1) Press the ON/OFF button.
(2) Make sure that the POWER lamp stops flashing.
b Turn the computer on and start Windows.
f Read the License Agreement carefully and click Yes.
Follow the on-screen instructions to install the software.
If a message asking for your confirmation to restart your
computer appears, click OK.
g When the Printer Connection screen appears, connect the
machine with a USB cable, then turn the machine on. The
software will begin identifying the printer port being used.
Important
If you cannot go to the next procedure after 3 minutes, refer to “Troubleshooting” instructions in the User’s Guide on-screen manual.
Important
Since Mac® OS 9, Mac OS X Classic environments, or Mac OS X v.10.2.7 or
earlier are not supported, do not connect the machine to these.
•
•
•
•
Note
Use Mac OS X v.10.2.8 to 10.4.x.
The screens below refer to Mac OS X v.10.4.x installation. Screens may vary
depending on the operating system you are using.
Log on as an Administrator before continuing.
Before installing the driver, disable all anti-virus programs and automatically
loading programs.
a Connect one end of the USB cable to the computer, the
other to the machine.
Note
Make sure the machine is turned on.
Important
If you see the Found New Hardware Wizard, remove the USB cable. Click
Cancel to quit the screen. Next, turn off the machine. Then proceed from step
3 to install the MP Drivers.
g When the list of applications to install appears, confirm the
contents, then click Install.
Note
Move the cursor over items to display explanations of each application.
h Read the License Agreement carefully and click Yes.
Follow the on-screen instructions to install the software.
i Follow the on-screen instructions to register your product.
Note
When the User Registration screen appears, follow on-screen instructions to
register your product. You will need your product serial number, which is located
on the inside of the machine. See Step 1- f on the front page.
j When the Installation completed successfully screen
appears, click Restart.
b Turn on your Mac.
c Insert the Setup CD-ROM.
c Insert the Setup CD-ROM. The setup program should run
Note
If the CD-ROM folder does not open automatically, double-click the CD-ROM icon
on the desktop.
automatically.
Note
The setup program should run automatically. If the installer in the CD-ROM does
not run automatically, click Start and select My Computer, then double-click the
CD-ROM icon
.
d When the main menu appears, click Easy Install.
d Double-click the Setup icon.
h Follow the on-screen instructions to register your product.
Note
When the User Registration screen appears, follow on-screen instructions to
register your product. You will need your product serial number, which is located on
the inside of the machine. See Step 1- f on the front page.
e When the Authenticate screen appears, enter your
administrator name and password. Click OK.
If you do not know your administrator name or password,
click , then follow the on-screen instructions.
i When the Installation completed successfully screen
appears, click Exit.
Note
• Select Easy Install in order to install the MP Drivers, on-screen manuals, and
application software. Select Custom Install in order to choose the options you
would like to install.
• To install Adobe® RGB (1998), click Custom Install and follow the on-screen
instructions. If you are using Windows Me/98, Adobe RGB cannot be installed.
e When the list of applications to install appears, confirm the
contents, click Install.
Note
Move the cursor over items to display explanations of each application.
The system is restarted automatically.
*When using Mac OS X v.10.2.8 to v.10.3.3:
Restarting the computer while connected to the machine may cause the
machine not to be detected. To resolve this, either unplug the USB cable
then plug it back in again, or turn the machine off then back on again.
k After restarting the computer, start Printer Setup Utility
(start Print Center if you are using Mac OS X v.10.2.8) and
then check that the printer name you want to use is shown
in Printer List. If the printer name is not displayed, click
Add to add the device.
For more detailed instructions, refer to the Mac on-screen
Help.
Now you have completed installation of the
software.
f When the main menu appears, click Easy Install.
If Restart is displayed, make sure that the Restart the system now
(recommended) check box is selected, then click Restart.
Now you have completed installation of the
software.
Note
Select Easy Install in order to install the MP Drivers, on-screen manuals, and
application software. Select Custom Install in order to choose the options you
would like to install.
Part no. QT5-0683-V02 © 2006 Canon Inc. Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the U.S. and/or other countries. Macintosh and Mac are trademarks of Apple Computer, Inc., registered in the U.S. and other countries. Adobe and Adobe RGB (1998) are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries. All other product and brand
Printed in Thailand.
names are trademarks of their respective owners. Specifications subject to change without notice.
Download PDF