Epson | EB-W22 | User`s guide | Epson EB-W22 User`s guide

User’s Guide
Notations Used in This Guide
• Safety indications
The documentation and the projector use graphical symbols to show how to use the projector safely.
Please understand and respect these caution symbols in order to avoid injury to persons or property.
Warning
This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling.
Caution
This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling.
• General information indications
Attention
a
Indicates procedures which may result in damage or injury if sufficient care is not taken.
Indicates additional information and points which may be useful to know regarding a topic.
s
Indicates a page where detailed information regarding a topic can be found.
g
Indicates that an explanation of the underlined word or words in front of this symbol appears in the glossary of terms. See the "Glossary"
section of the "Appendix".
s "Glossary" p.140
[Name]
Menu Name
Indicates the name of the buttons on the remote control or the control panel.
Example: [Esc] button
Indicates Configuration menu items.
Example:
Select Brightness from Image.
Image - Brightness
Contents
3
Notations Used in This Guide . . . . . . . . . . . . . . . . . . . . . . . . 2
Installing the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Introduction
Projector Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Quick and Easy Set up, Projection, and Storage . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Connecting with a USB cable and projecting (USB Display) . . . . . . . . . . . . . . . . 8
Detecting projector movements and automatically correcting image distortion
......................................................... 8
Horizontal keystone adjuster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Useful Functions for Projecting Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Increasing projection content in wide (WXGA) screen (EB-W22 only) . . . . . . . . . . 8
Connect a USB storage device and project movies or images (PC Free) . . . . . . . . 9
Various functions for excellent power saving . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Making the most of the remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Enlarge and project your files with the Document Camera . . . . . . . . . . . . . . . . . 9
Enhanced security functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Taking Full Advantage of a Network Connection . . . . . . . . . . . . . . . . . . . . . . . . . 9
Connecting to a network and projecting images from the computer's screen
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Easy connection to a computer with Quick Wireless Connection (Windows only)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Projecting images from portable devices over a network . . . . . . . . . . . . . . . . . 10
Projecting images from multiple computers simultaneously (EB-X25/EB-W22/EBX22/EB-X20 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Part Names and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Front/Top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacing the remote control batteries . . . . . . . . . . . . . . . . . . . .
Remote control operating range . . . . . . . . . . . . . . . . . . . . . . . .
Preparing the Projector
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
11
13
14
15
16
19
20
Installation Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Installation methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Screen Size and Approximate Projection Distance . . . . . . . . . . . . . . . . . . . . . . . 23
Connecting Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Connecting a Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting Image Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting USB Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting External Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting a LAN Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the Wireless LAN Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the Quick Wireless Connection USB Key . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
25
26
27
28
30
31
32
Basic Usage
Projecting Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
From Installation to Projection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatically Detect Input Signals and Change the Projected Image (Source Search)
... ....... ......... ... ....... ......... ... ....... ..........
Switching to the Target Image by Remote Control . . . . . . . . . . . . . . . . . . . . . . .
Projecting with USB Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting for the first time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Uninstalling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
34
35
36
36
36
37
39
Adjusting Projected Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Correcting Keystone Distortion . . . . . . . . . . . . . . . . . . . . . . .
Correcting automatically . . . . . . . . . . . . . . . . . . . . . . . . .
Correcting manually . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the Image Size . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the Image Position . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the Horizontal Tilt . . . . . . . . . . . . . . . . . . . . . . . . .
Correcting the Focus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
40
41
41
44
45
45
45
46
Contents
Selecting the Projection Quality (Selecting Color Mode) . . . . . . . . . . . . . .
Setting Auto Iris . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing the Aspect Ratio of the Projected Image . . . . . . . . . . . . . . . . . .
Changing methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing the aspect mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
46
47
47
48
48
Useful Functions
Projection Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Projecting Without a Computer (PC Free) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications for files that can be projected using PC Free . . . . . . . . . . . . . .
PC Free examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PC Free operating methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Projecting the selected image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Projecting image files in a folder in sequence (Slideshow) . . . . . . . . . . . . . . .
Image file display settings and Slideshow operation settings . . . . . . . . . . . . .
Hiding the Image and Sound Temporarily (A/V Mute) . . . . . . . . . . . . . . . . . . . .
Freezing the Image (Freeze) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pointer Function (Pointer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enlarging Part of the Image (E-Zoom) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the Remote Control to Operate the Mouse Pointer (Wireless Mouse) . . . . .
Saving a User's Logo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Saving User Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
52
52
52
53
55
56
57
57
58
58
59
60
61
63
Security Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Managing Users (Password Protect) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Kinds of Password Protect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting Password Protect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Entering the Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Restricting Operation (Control Panel Lock) . . . . . . . . . . . . . . . . . . . . . . .
Anti-Theft Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the wire lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
65
65
65
66
67
69
69
Monitoring and Controlling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
EasyMP Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Changing Settings Using a Web Browser (Web Control) . . . . . . . . . . . . . . . . . . . . 70
Projector setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Displaying the Web Control screen . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Displaying the Web Remote screen . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the Mail Notification Function to Report Problems . . . . . . . . . . . . . . . .
Reading Error Notification Mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Management Using SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ESC/VP21 Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Command list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cable layouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About PJLink (EB-X25/EB-W22/EB-X22/EB-X20 Only) . . . . . . . . . . . . . . . . . . .
About Crestron RoomView (EB-X25/EB-W22/EB-X22/EB-X20 only) . . . . . . . .
Operating a projector from your computer . . . . . . . . . . . . . . . . . . . . . . .
®
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
70
71
72
72
73
73
73
74
75
75
76
About Event ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Configuration Menu
Using the Configuration Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
List of Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Configuration Menu Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Network menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Image Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Signal Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Settings Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Extended Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Network Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Notes on operating the Network menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Soft keyboard operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Basic menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Wireless LAN menu (EB-X21/EB-S21/EB-X17/EB-S17 only) . . . . . . . . . . . . . . . . 93
Security menu (EB-X21/EB-S21/EB-X17/EB-S17 only) . . . . . . . . . . . . . . . . . . . . 95
Wired LAN menu (EB-X25/EB-W22/EB-X22/EB-X20 only) . . . . . . . . . . . . . . . . . 96
Mail menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Others menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Reset menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
ECO Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Info Menu (Display Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Contents
5
Reset Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Replacing Consumables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Troubleshooting
Using the Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Problem Solving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Reading the Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
When the Indicators Provide No Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Problems Relating to Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
No images appear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Moving images are not displayed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Projection stops automatically . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The message Not supported is displayed . . . . . . . . . . . . . . . . . . . . . . . . . . .
The message No Signal is displayed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Images are fuzzy, out of focus, or distorted . . . . . . . . . . . . . . . . . . . . . . . . .
Interference or distortion appear in images . . . . . . . . . . . . . . . . . . . . . . . . .
The image is truncated (large) or small, the aspect is not suitable, or the image has
been reversed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Image colors are not right . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Images appear dark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Problems when Projection Starts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The projector does not turn on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Other Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
No sound can be heard or the sound is faint . . . . . . . . . . . . . . . . . . . . . . . .
There is noise in the audio (when projecting EasyMP Network Projection, EasyMP
MultiPC Projection, USB Display, or Quick Wireless Connection) . . . . . . . . . . .
The remote control does not work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I want to change the language for messages and menus . . . . . . . . . . . . . . . .
Mail is not received even if a problem occurs in the projector . . . . . . . . . . . . .
Cannot change settings using a Web browser . . . . . . . . . . . . . . . . . . . . . . .
Cleaning the Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Cleaning the Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
104
108
109
109
110
110
110
111
111
112
113
113
114
115
115
115
115
116
116
117
117
117
Maintenance
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Cleaning the Projector's Surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Replacing the Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lamp replacement period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How to replace the lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Resetting the lamp hours . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacing the Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Air filter replacement period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How to replace the air filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
121
121
121
124
124
124
124
Appendix
Optional Accessories and Consumables . . . . . . . . . . . . . . . . . . . . 127
Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Consumables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Screen Size and Projection Distance . . . . . . . . . . . . . . . . . . . . . . . . 128
Projection Distance (For EB-X25) . . . . . . . . . . . . . . . . . . . . . . .
Projection Distance (For EB-X22/EB-X21/EB-X20/EB-X17) . . . . . . .
Projection Distance (For EB-W22) . . . . . . . . . . . . . . . . . . . . . . .
Projection Distance (For EB-S21/EB-S17) . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
128
129
130
131
Supported Monitor Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Supported Resolutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Computer signals (analog RGB) . . . . . . . . . . . . . . . . . . . . . . . . .
Component video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Composite video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input signal from the HDMI port . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
133
133
133
134
134
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
Projector General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
Contents
Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
General Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
About Notations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
General Notice: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
6
Introduction
This chapter explains the projector's features and the part names.
Projector Features
Quick and Easy Set up, Projection, and Storage
•
•
•
•
Turn the projector on and off by simply plugging in or unplugging.
Project onto large screens from a short distance.
Make easy height adjustments with one lever.
No cool down delay makes it easy to put away.
8
Horizontal keystone adjuster
This allows you to quickly correct horizontal distortion in the projected
image. This is useful if you cannot install the projector parallel to the
screen.
s "Correcting manually" p.41
Connecting with a USB cable and projecting (USB Display)
By simply connecting a USB cable, you can
project images from a computer's screen
without a computer cable.
s "Projecting with USB Display" p.36
Useful Functions for Projecting Images
Detecting projector movements and automatically correcting
image distortion
This projector automatically corrects vertical keystone distortion which
occurs when positioning or moving the projector.
s "Correcting automatically" p.41
Increasing projection content in wide (WXGA) screen (EB-W22
only)
With a computer that has a 16:10 WXGA wide
LCD display, the image can be projected in the
same aspect. You can use whiteboards and other
landscape format screens.
s "Changing the Aspect Ratio of the Projected
Image" p.47
Projector Features
Connect a USB storage device and project movies or images (PC
Free)
9
Enlarge and project your files with the Document Camera
Only EB-X21/EB-S21/EB-X17/EB-S17 are supported.
You can project paper documents and objects using the optional Document
Camera.
You can connect USB storage devices or digital cameras to the projector
and project saved images.
By connecting to a computer and using the software supplied, you can
make full use of the projector's capabilities.
A wide range of file formats are supported such as movies or images.
s "Optional Accessories" p.127
s "Projecting Without a Computer (PC Free)" p.52
Enhanced security functions
Various functions for excellent power saving
• Various functions to prevent wasting electricity
The projector comes with a number of built-in functions to save power
such as dimming the projected image, an auto power off timer, and
adjusting power consumption while the projector is standing by.
s "ECO Menu" p.99
• Function for displaying the power-saving status on the projected screen
When ECO Display is set to On from the Configuration menu, leaf icons
(
) that indicate the power-saving status are displayed at the bottomleft of the projected screen when the lamp brightness has switched to low
brightness.
s ECO - ECO Display p.99
• Password Protect to restrict and manage users
By setting a Password you can restrict who can use the projector.
s "Managing Users (Password Protect)" p.65
• Control Panel Lock to restrict button operation on the control panel
You can use this to prevent people changing projector settings without
permission at events, in schools, and so on.
s "Restricting Operation (Control Panel Lock)" p.67
• Equipped with various anti-theft devices
The projector is equipped with the following types of anti-theft security
devices.
• Security slot
• Security cable installation point
s "Anti-Theft Lock" p.69
Making the most of the remote control
You can use the remote control to perform operations such as enlarging
part of the image. You can also use the remote control as a pointer during
presentations or as a mouse for the computer.
s "Pointer Function (Pointer)" p.58
s "Enlarging Part of the Image (E-Zoom)" p.59
s "Using the Remote Control to Operate the Mouse Pointer (Wireless
Mouse)" p.60
Taking Full Advantage of a Network Connection
By connecting a LAN cable (EB-X25/EB-W22/EB-X22/EB-X20 only), or the
optional Wireless LAN unit (EB-X21/EB-S21/EB-X17/EB-S17 only), you can
connect to a network and access the following functions.
s "Connecting a LAN Cable" p.30
s "Installing the Wireless LAN Unit" p.31
Projector Features
Connecting to a network and projecting images from the
computer's screen
You can project your computer's screen over a
network by using EasyMP Network Projection.
Sharing the projector over the network allows
you to project data from different computers
without changing the signal cable. Even if the
projector is away from the computer, you can
still project data over a network.
You can find Easy Network Projection on the
EPSON Projector Software CD-ROM.
Easy connection to a computer with Quick Wireless Connection
(Windows only)
By simply connecting the optional Quick
Wireless Connection USB Key to a computer,
you can automatically setup a wireless LAN
connection.
s "Installing the Quick Wireless Connection
USB Key" p.32
Projecting images from portable devices over a network
If "Epson iProjection" is installed on your smart
phone or tablet device, you can wirelessly
project data from the device. Because you can
operate these devices from any location, you can
vary the way in which conferences or
presentations are made.
10
You can download "Epson iProjection" for free from the App Store or from
Google play. Any fees incurred when communicating with the App Store or
Google play are the responsibility of the customer.
Projecting images from multiple computers simultaneously (EBX25/EB-W22/EB-X22/EB-X20 only)
By using EasyMP Multi PC Projection, up to four screens from multiple
computers connected to the network, or from smartphones or tablets with
Epson iProjection installed, can be projected simultaneously adding a touch
of dynamism to conferences that use projectors. By making yourself the
host of a meeting, you can control the projected screens from other
connected computers allowing you to advance the meeting smoothly.
You can also project the same screen from remote projectors on the
network.
You can find EasyMP Multi PC Projection on the EPSON Projector
Software CD-ROM.
Part Names and Functions
All of the features in this guide are explained using illustrations of EB-X21
unless otherwise mentioned.
11
Front/Top
EB-S21/EB-S17
Name
A Air exhaust vent
Function
Exhaust vent for air used to cool the projector internally.
Caution
While projecting, do not put your face or hands
near the air exhaust vent, and do not place objects
that may become warped or damaged by heat near
the vent. Hot air from the air exhaust vent could
cause burns, warping, or accidents to occur.
Part Names and Functions
Name
12
Function
Name
Function
B A/V mute slide knob
Slide the knob to open and close the A/V mute slide.
N Lamp cover
C Foot adjust lever
Press the foot adjust lever to extend and retract the front
adjustable foot.
s "Adjusting the Image Position" p.45
Open when replacing the projector's lamp.
s "Replacing the Lamp" p.121
O Lamp Cover Fixing
Screw
Screw to fix the lamp cover in place.
D Front adjustable foot
When setup on a surface such as a desk, extend the foot to
adjust the position of the image.
s "Adjusting the Image Position" p.45
E A/V mute slide
Close when not using the projector to protect the lens. By
closing during projection you can hide the image and the
sound.
s "Hiding the Image and Sound Temporarily (A/V
Mute)" p.57
F Remote receiver
Receives signals from the remote control.
G Focus ring
Adjusts the image focus.
s "Correcting the Focus" p.45
H Zoom ring
(EB-X25/EB-W22/EBX22/EB-X21/EB-X20/
EB-X17 only)
Adjusts the image size.
s "Adjusting the Image Size" p.44
I Air intake vent
(air filter)
Takes in air to cool the projector internally.
s "Cleaning the Air Filter" p.119
J Air filter cover
Opens and closes the air filter cover.
s "Replacing the Air Filter" p.124
K Security slot
The security slot is compatible with the Microsaver
Security System manufactured by Kensington.
s "Anti-Theft Lock" p.69
L Control panel
Operates the projector.
s "Control Panel" p.15
M Horizontal keystone
adjuster
Corrects horizontal distortion in the projected image.
s "Correcting manually" p.41
Part Names and Functions
Rear
EB-X21/EB-S21/EB-X17/EB-S17
EB-X25/EB-W22/EB-X22/EB-X20
13
The ports vary depending on the model being used.
Name
Function
A Power inlet
Connects the power cord to the projector.
s "From Installation to Projection" p.34
B S-Video port
For S-video signals from video sources.
C RS-232C port
When controlling the device from a computer, connect it
to the computer with an RS-232C cable. This port is for
control use and should not normally be used.
s "ESC/VP21 Commands" p.73
D Video port
Inputs composite video signals from video sources.
E Audio-L/R port
Inputs audio from equipment connected to the S-Video
port or the Video port.
F Monitor Out port
Outputs analog RGB signals input from the Computer1
port to an external monitor. You cannot output signals
input from other ports or component video signals.
G Audio1 port
Inputs audio from equipment connected to the
Computer1 port.
H Audio Output port
Outputs audio from the currently projected image to an
external speaker.
I Audio2 port
Inputs audio from equipment connected to the
Computer2 port.
J Speaker
Outputs audio.
K Remote receiver
Receives signals from the remote control.
L HDMI port
Inputs video signals from HDMI compatible video
equipment and computers. This projector is compatible
with HDCPg.
s "Connecting Image Sources" p.26
M Computer2 port
Inputs image signals from a computer and component
video signals from other video sources.
N Computer1 port
Part Names and Functions
Name
14
Function
O LAN port (EB-X25/EBW22/EB-X22/EB-X20
only)
Connects a LAN cable to connect to a network.
P USB-B port
• Connects the projector to a computer using a USB cable,
and projects the images on the computer.
s "Projecting with USB Display" p.36
• Connects the projector to a computer using a USB cable
to use the Wireless Mouse function.
s "Using the Remote Control to Operate the
Mouse Pointer (Wireless Mouse)" p.60
Q USB-A port (EB-X21/
EB-S21/EB-X17/EBS17 only)
• Connects a USB memory device or a digital camera, and
projects images using PC Free.
s "Projecting Without a Computer (PC Free)"
p.52
• Connects the optional Document Camera.
Base
• Connects the optional Wireless LAN unit.
s "Installing the Wireless LAN Unit" p.31
• Connects the optional Quick Wireless Connection USB
Key.
s "Installing the Quick Wireless Connection USB
Key" p.32
R Wireless LAN unit
fixing screw (EB-X21/
EB-S21/EB-X17/EBS17 only)
This screw secures the wireless LAN unit cover.
Name
Function
A Ceiling mount fixing
points (three points)
Attach the optional Ceiling Mount here when suspending
the projector from a ceiling.
s "Installing the Projector" p.22
s "Optional Accessories" p.127
B Security cable
installation point
Pass a commercially available wire lock through here and
lock it in place.
s "Installing the wire lock" p.69
Part Names and Functions
Name
15
Function
C Rear feet
When setup on a surface such as a desk, turn to extend and
retract to adjust the horizontal tilt.
s "Adjusting the Horizontal Tilt" p.45
D Front adjustable foot
When setup on a surface such as a desk, extend the foot to
adjust the position of the image.
s "Adjusting the Image Position" p.45
Control Panel
Name
Function
A [Source Search]
button
Changes to the next input source that is sending an image.
s "Automatically Detect Input Signals and Change the
Projected Image (Source Search)" p.35
B [Enter] button
[ ]
• When the Configuration menu or the Help screen is
displayed, it accepts and enters the current selection and
moves to the next level.
• If pressed while projecting analog RGB signals from the
Computer port, you can automatically optimize
Tracking, Sync., and Position.
C [w][v] buttons
• Displays the Keystone screen allowing you to correct
keystone distortion in vertical and horizontal
directions.
s "Correcting manually" p.41
• If pressed when the Configuration menu or the Help
screen is displayed, these buttons select menu items and
setting values.
s "Using the Configuration Menu" p.82
s "Using the Help" p.103
Part Names and Functions
Name
16
Function
D [Help] button
Displays and closes the Help screen which shows you how
to deal with problems if they occur.
s "Using the Help" p.103
E [Esc] button
• Stops the current function.
• If pressed when the Configuration menu is displayed, it
moves to the previous menu level.
s "Using the Configuration Menu" p.82
F [a][b] buttons
or [Wide][Tele]
buttons
• For EB-X25/EB-W22/EB-X22/EB-X21/EB-X20/EBX17
[a] Decreases the volume.
[b] Increases the volume.
s "Adjusting the Volume" p.46
• For EB-S21/EB-S17
[Wide]: Enlarges the size of the projected image.
[Tele]: Reduces the size of the projected image.
s "Adjusting the Image Size" p.44
• Corrects keystone distortion in the horizontal direction
when the Keystone screen is displayed.
s "H/V-Keystone" p.42
• If pressed when the Configuration menu or the Help
screen is displayed, these buttons select menu items and
setting values.
s "Using the Configuration Menu" p.82
s "Using the Help" p.103
G [Menu] button
Displays and closes the Configuration menu.
s "Using the Configuration Menu" p.82
H Power button
[t]
Turns the projector power on or off.
s "From Installation to Projection" p.34
I Indicators
Indicates the projector's status.
s "Reading the Indicators" p.104
Remote Control
Part Names and Functions
Name
17
Function
A Power button
[t]
Turns the projector power on or off.
s "From Installation to Projection" p.34
B [Computer] button
Each time you press the button, the input changes between
images from the Computer1 port and the Computer2
port.
C [Video] button
Each time the button is pressed, the image cycles through
the S-Video, Video, and HDMI ports.
D Numeric buttons
Enter the Password.
s "Setting Password Protect" p.65
E [Auto] button
If pressed while projecting analog RGB signals from the
Computer port, you can automatically optimize Tracking,
Sync., and Position.
F [Aspect] button
Each time the button is pressed, the aspect mode changes.
s "Changing the Aspect Ratio of the Projected Image"
p.47
G [Num] button
Hold down this button and press the numeric buttons to
enter passwords and numbers.
s "Setting Password Protect" p.65
H [Menu] button
Displays and closes the Configuration menu.
s "Using the Configuration Menu" p.82
I [
][
buttons
][
][
]
• When the Configuration menu or the Help screen is
displayed, pressing these buttons selects menu items
and setting values.
s "Using the Configuration Menu" p.82
• When projecting using PC Free, pressing these buttons
displays the previous/next image, rotates the image, and
so on.
s "PC Free operating methods" p.53
• During Wireless Mouse function, the mouse pointer
moves in the direction of the button that was pushed.
s "Using the Remote Control to Operate the
Mouse Pointer (Wireless Mouse)" p.60
Name
J [
] button
Function
• When the Configuration menu or the Help screen is
displayed, it accepts and enters the current selection and
moves to the next level.
s "Using the Configuration Menu" p.82
• Acts as a mouse's left button when using the Wireless
Mouse function.
s "Using the Remote Control to Operate the
Mouse Pointer (Wireless Mouse)" p.60
K [User] button
Select any frequently used item from the five available
Configuration menu items, and assign it to this button. By
pressing the [User] button, the assigned menu item
selection/adjustment screen is displayed, allowing you to
make one-touch settings/adjustments.
s "Settings Menu" p.88
Power Consumption is assigned as the default setting.
L [Page] buttons
[[][]]
Changes pages in files such as PowerPoint files when using
the following projection methods.
• When using the Wireless Mouse function
s "Using the Remote Control to Operate the
Mouse Pointer (Wireless Mouse)" p.60
• When using USB Display
s "Projecting with USB Display" p.36
• When using Network connection
When projecting images using PC Free, pressing these
buttons displays the previous/next screen.
M [E-Zoom] buttons
[z][x]
Enlarges or reduces the image without changing the
projection size.
s "Enlarging Part of the Image (E-Zoom)" p.59
Part Names and Functions
Name
N [A/V Mute] button
18
Function
• Turns the video and audio on or off.
s "Hiding the Image and Sound Temporarily (A/V
Mute)" p.57
• You can change the Projection mode as follows by
pressing the button for about five seconds.
FrontWFront/Ceiling
RearWRear/Ceiling
O [Help] button
Displays and closes the Help screen which shows you how
to deal with problems if they occur.
s "Using the Help" p.103
P [Freeze] button
Images are paused or unpaused.
s "Freezing the Image (Freeze)" p.58
Q [Volume] buttons
[a][b]
[a] Decreases the volume.
[b] Increases the volume.
s "Adjusting the Volume" p.46
R [Pointer] button
Displays the on-screen pointer.
s "Pointer Function (Pointer)" p.58
S [Esc] button
• Stops the current function.
• If pressed when the Configuration menu is displayed, it
moves to the previous level.
s "Using the Configuration Menu" p.82
• Acts as a mouse's right button when using the Wireless
Mouse function.
s "Using the Remote Control to Operate the
Mouse Pointer (Wireless Mouse)" p.60
T [Color Mode] button
Each time the button is pressed, the Color Mode changes.
s "Selecting the Projection Quality (Selecting Color
Mode)" p.46
U [LAN] button
Switches to the image from the network connected device.
Name
Function
V [USB] button
Each time the button is pressed, it cycles through the
following images:
• USB Display
• Images from the device connected to the USB-A port
W [Source Search]
button
Changes to the next input source that is sending an image.
s "Automatically Detect Input Signals and Change the
Projected Image (Source Search)" p.35
X Remote control lightemitting area
Outputs remote control signals.
Part Names and Functions
19
Replacing the remote control batteries
Caution
If delays in the responsiveness of the remote control occur or if it does not
operate after it has been used for some time, it probably means that the
batteries are becoming flat. When this happens, replace them with new
batteries. Have two AA size manganese or alkaline batteries ready. You
cannot use other batteries except for the AA size manganese or alkaline.
Attention
Make sure you read the following manual before handling the batteries.
s Safety Instructions
a
Remove the battery cover.
b
Replace the old batteries with new batteries.
While pushing the battery compartment cover catch, lift the cover
up.
Check the positions of the (+) and (-) marks inside the battery holder to
ensure the batteries are inserted the correct way.
If the batteries are not used correctly, they could explode or leak causing
a fire, injury, or damage to the product.
c
Replace the battery cover.
Press the battery compartment cover until it clicks into place.
Part Names and Functions
Remote control operating range
20
Preparing the Projector
This chapter explains how to install the projector and connect projection sources.
Installing the Projector
22
Installation Methods
Warning
The projector supports the following four different projection methods.
Install the projector according to the conditions of the installation location.
• Project images from in front of
the screen. (Front projection)
• Project images from behind a
translucent screen. (Rear projec‐
tion)
• Suspend the projector from the
ceiling and project images from
in front of a screen. (Front/Ceil‐
ing projection)
• Suspend the projector from the
ceiling and project images from
behind a translucent screen.
(Rear/Ceiling projection)
• A special method of installation is required when suspending the projector
from a ceiling (ceiling mount). If it is not installed correctly, it could fall
causing an accident and injury.
• If you use adhesives on the Ceiling mount fixing points to prevent the screws
from loosening, or if you use things such as lubricants or oils on the
projector, the projector case may crack causing it to fall from its ceiling
mount. This could cause serious injury to anyone under the ceiling mount
and could damage the projector.
When installing or adjusting the ceiling mount, do not use adhesives to
prevent the screws from loosening and do not use oils or lubricants and so
on.
• Do not cover the projector's air intake vent or air exhaust vent. If either of
the vents are covered, the internal temperature could rise and cause a fire.
Attention
Do not use the projector on its side. This may cause malfunctions to occur.
a
• An optional Ceiling mount is required when suspending the
projector from a ceiling.
s "Optional Accessories" p.127
• The default Projection setting is Front. You can change from Front
to Rear from the Configuration menu.
s Extended - Projection p.89
• You can change the Projection mode as follows by pressing down
the [A/V Mute] button on the remote control for about five seconds.
FrontWFront/Ceiling
RearWRear/Ceiling
Installing the Projector
Installation methods
Install the projector as follows.
23
a
• Install the projector so that it is parallel to the screen.
If the projector is installed at an angle to the screen, keystone distortion
occurs in the projected image.
• See the following if you cannot install the projector parallel to the
screen.
s "Correcting Keystone Distortion" p.40
• See the following if you cannot install the projector on a level
surface.
s "Adjusting the Horizontal Tilt" p.45
s "Correcting Keystone Distortion" p.40
Screen Size and Approximate Projection Distance
• Place the projector on a level surface.
If the projector is tilted the projected image is also tilted.
Projection size is determined by the distance from the projector to the
screen. See the illustrations on the right to select the best position according
to the screen size. The illustrations show the approximate shortest distance
at maximum zoom. See the following for more information on the
projection distance.
s "Screen Size and Projection Distance" p.128
a
When you correct keystone distortion, the projected image may be
reduced.
Installing the Projector
24
For EB-X25
16:10 Screen Size
For EB-W22
150”
150”
100”
80”
100”
80”
50”
50”
4:3 Screen Size
For EB-X22/EB-X21/EB-S21/EB-X20/EB-X17/EB-S17
150”
100”
80”
50”
Connecting Equipment
25
Illustrations in this section are of EB-X21.
The port name, number, location, and connector orientation differ depending on the source being connected.
Connecting a Computer
To project images from a computer, connect the computer using one of the following methods.
A When using the supplied computer cable
Connect the computer's display output port to the projector's Computer port. You can output audio from the projector's speaker by connecting the computer's audio output port to the
projector's Audio1 or Audio2 port using a commercially available audio cable.
B When using the supplied or commercially available USB cable
Connect the computer's USB port to the projector's USB-B port. You can send the computer's audio with the projected image.
C When using a commercially available HDMI cable
Connect the computer's HDMI port to the projector's HDMI port. You can send the computer's audio with the projected image.
a
• You can change the audio input source in Audio Output.
s Extended - A/V Settings - Audio Output p.89
• You can use a USB cable to connect the projector to a computer to project images from the computer. This function is called USB Display.
s "Projecting with USB Display" p.36
Connecting Equipment
26
Connecting Image Sources
To project images from DVD players or VHS video and so on, connect to the projector using one of the following methods.
A When using a commercially available video or S-video cable
Connect the video output port on the image source to the projector's Video port. Or, connect the S-video output port on the image source to the projector's S-Video port. You can
output audio from the projector's speaker by connecting the audio output port on the image source to the projector's Audio-L/R port using a commercially available audio cable.
B When using the optional component video cable
s "Optional Accessories" p.127
Connect the component output port on the image source to the projector's Computer input port. You can output audio from the projector's speaker by connecting the audio output
port on the image source to the projector's Audio1 or Audio2 port using a commercially available audio cable.
C When using a commercially available HDMI cable
Connect the HDMI port on the image source to the projector's HDMI port. You can send the image source's audio with the projected image.
S-VIDEO
Connecting Equipment
27
Attention
If the orientation or shape of the plug differs, do not try to force it in. The device could be damaged or could malfunction.
a
• You can change the audio input source in Audio Output.
s Extended - A/V Settings - Audio Output p.89
• If the source you want to connect to has an unusually shaped port, use the cable supplied with the device or an optional cable to connect to the projectors.
• When using a commercially available 2RCA(L/R)/stereo mini-pin audio cable, make sure it is labeled "No resistance".
Connecting USB Devices
Only EB-X21/EB-S21/EB-X17/EB-S17 are supported.
You can connect devices such as USB memory, the optional Document Camera, and USB compatible hard disks and digital cameras.
Using the USB cable supplied with the USB device, connect the USB device to the USB-A port on the projector.
When the USB device is connected, you can project image files on the USB memory or digital camera using PC Free.
s "PC Free examples" p.52
Connecting Equipment
28
Attention
•
•
•
•
If you use a USB hub, the connection may not operate correctly. Devices such as digital cameras and USB devices should be connected to the projector directly.
When connecting and using a USB-compatible hard disk, make sure you connect the AC adaptor supplied with the hard disk.
Connect a digital camera or hard disk to the projector using the USB cable provided with the device.
Use a USB cable less than three meters in length. If the cable exceeds three meters, PC Free may not function correctly.
Removing USB devices
After finishing projecting, remove USB devices from the projector. For devices such as digital cameras or hard disks, turn off the device and then remove it from
the projector.
Connecting External Equipment
You can output images and audio by connecting an external monitor or speaker.
A When outputting images to an external monitor
Connect the external monitor to the projector's Monitor Out port using the cable supplied with the external monitor.
B When outputting audio to an external speaker
Connect the external speaker to the projector's Audio Out port using a commercially available audio cable.
Connecting Equipment
a
29
• If you set Standby Mode to Communication On, you can perform the following operations even if the projector is off.
- Outputting images to an external monitor (only when A/V Output is set to Always On).
- Outputting audio from an externally connected speaker (audio from USB or LAN cannot be output).
s ECO - Standby Mode p.99
s Extended - A/V Settings p.89
• Only analog RGB signals from the Computer1 port can be output to an external monitor. You cannot output signals input from other ports or component video
signals.
• Setting gauges for functions such as Keystone, Configuration Menu, or Help screens are not output to the external monitor.
• When the audio cable jack is inserted into the Audio Out port, audio stops being output from the projector's built-in speakers and switches to external
output.
Connecting Equipment
Connecting a LAN Cable
Only EB-X25/EB-W22/EB-X22/EB-X20 are supported.
Connect a LAN port on network hubs or other equipment to the projector's LAN port with a commercially available 100BASE-TX or 10BASE-T LAN
cable.
By connecting a computer to the projector over a network, you can project images and check the status of the projector.
a
To prevent malfunctions, use a category 5 or higher shielded LAN cable.
30
Connecting Equipment
Installing the Wireless LAN Unit
31
b
Connect the wireless LAN unit to the USB-A port.
c
Attach the wireless LAN unit cover, and secure it in place with the
screw.
Only EB-X21/EB-S21/EB-X17/EB-S17 are supported.
By installing the optional Wireless LAN unit, you can project a computer
screen over a network.
Connect the wireless LAN unit to the projector's USB-A port.
a
• When connecting to the network using wireless LAN, make sure you
make network settings from the Configuration menu.
s "Wireless LAN menu (EB-X21/EB-S21/EB-X17/EB-S17 only)"
p.93
• If you normally leave the wireless LAN unit installed, make sure you
attach the supplied wireless LAN unit cover as a theft deterrent.
• When moving the projector, make sure you remove the wireless
LAN unit and cover for safety reasons.
a
Use a cross-head screwdriver to remove the screw that secures the
wireless LAN unit cover.
Connecting Equipment
Installing the Quick Wireless Connection USB Key
When installing the optional Quick Wireless Connection USB Key, you
need to remove the Wireless LAN unit first, and then connect the Quick
Wireless Connection USB Key to the USB-A port.
a
Turn on the projector, and then press the [LAN] button on the
remote control.
The LAN standby screen is displayed.
b
Check that the SSID and IP address information are displayed on
the LAN standby screen, and then remove the Wireless LAN
unit.
c
Connect the Quick Wireless Connection USB Key to the USB-A
port.
d
When the message "Network information update complete.
Remove the Quick Wireless Connection USB Key Adapter." is
displayed, remove the Quick Wireless Connection USB Key.
e
Reinstall the Wireless LAN unit on the projector.
32
f
Connect the Quick Wireless Connection USB Key to the computer
you are using.
For the steps from here on, see the User's Guide supplied with the
Quick Wireless Connection USB Key.
Basic Usage
This chapter explains how to project and adjust images.
Projecting Images
From Installation to Projection
This section explains the procedure for connecting the projector to a
computer with the computer cable and projecting images.
Attention
Be sure to connect the cable of the source to the projector first, and then
connect the power cord to the projector.
34
c
d
e
f
Turn on the projector.
Open the A/V mute slide.
Turn on your computer.
Change the computer's screen output.
When using a laptop computer, you need to change the screen
output from the computer.
Hold down the Fn key (function key), and press the b key.
a
• The method for changing differs depending on the computer
being used. See the documentation supplied with the
computer.
• When turning off the projector, press the [t] power button
twice.
If the image is not projected, you can change the projected image using one
of the following methods.
• Press the [Source Search] button on the control panel or the remote
control.
s "Automatically Detect Input Signals and Change the Projected Image
(Source Search)" p.35
• Press the button for the target port on the remote control.
s "Switching to the Target Image by Remote Control" p.36
a
a
b
Connect the projector to the computer with the computer cable.
Connect the projector to an electrical outlet with the power cord.
After projecting the image, adjust the image if necessary.
s "Correcting Keystone Distortion" p.40
s "Correcting the Focus" p.45
Projecting Images
35
Automatically Detect Input Signals and Change
the Projected Image (Source Search)
Press the [Source Search] button to project images from the port currently
receiving an image.
Using the remote control
Using the control panel
For EB-X21/EB-S21/EB-X17/EB-S17
For EB-X25/EB-W22/EB-X22/EB-X20
When two or more image sources are connected, press the [Source Search]
button until the target image is projected.
When your video equipment is connected, start playback before beginning
this operation.
a
The following screen is displayed while no image signals are input.
Example: For EB-X21/EB-S21/EB-X17/EB-S17
Projecting Images
36
Switching to the Target Image by Remote Control
You can change directly to the target image by pressing the following
buttons on the remote control.
Remote control
Projecting with USB Display
You can use a USB cable to connect the projector to a computer to project
images from the computer.
You can project images and send audio with one USB cable.
System requirements
For Windows
OS
A Each time the button is pressed, it cycles through the images being input
from the following sources.
• Computer1
• Computer2
B Each time the button is pressed, it cycles through the images being input
from the following sources.
• S-Video port
• Video port
• HDMI port
C Each time the button is pressed, it cycles through the images being input
from the following sources.
• USB Display
• Images from the device connected to the USB-A port (EBX21/EB-S21/EB-X17/EB-S17 only)
D Switches to the image from the network connected device.
Windows 2000*1
Windows XP*2
Professional 32bit
Home Edition 32bit
Tablet PC Edition 32bit
Windows Vista
Ultimate 32bit
Enterprise 32bit
Business 32bit
Home Premium 32bit
Home Basic 32bit
Windows 7
Ultimate 32/64bit
Enterprise 32/64bit
Professional 32/64bit
Home Premium 32/64bit
Home Basic 32bit
Starter 32bit
Windows 8
Windows 8 32/64 bit
Windows 8 Pro 32/64 bit
Windows 8 Enterprise 32/64 bit
CPU
Mobile Pentium III 1.2 GHz or faster
Recommended: Pentium M 1.6 GHz or faster
Amount of
Memory
256 MB or more
Recommended: 512 MB or more
Projecting Images
Hard Disk
Space
20 MB or more
Display
Resolution of no less than 640x480 and no higher than
1600x1200.
Display color in 16-bit color or greater
*1 Service Pack 4 only
*2 Except for Service Pack 1
37
Connecting for the first time
The first time you connect the projector and the computer using the USB
cable, the driver needs to be installed. The procedure is different for
Windows and Mac OS.
a
For Mac OS
• You do not need to install the driver the next time you connect.
• When inputting images from multiple sources, change the input
source to USB Display.
• If you use a USB hub, the connection may not operate correctly.
Connect the USB cable directly to the projector.
• You cannot change option settings while using USB Display.
Mac OS X 10.5.x 32 bit
Mac OS X 10.6.x 32/64 bit
Mac OS X 10.7.x 32/64 bit
Mac OS X 10.8.x 32/64 bit
For Windows
CPU
Power PC G4 1GHz or faster
Recommended: Core Duo 1.83GHz or faster
a
Amount of
Memory
512 MB or more
Hard Disk
Space
20 MB or more
Display
Resolution of no less than 640x480 and no higher than
1680x1200.
Display color in 16-bit color or greater
OS
Connect the computer's USB port to the projector's USB-B port
using a USB cable.
a
For Windows 2000 or Windows XP, a message asking you if
you want to restart your computer may be displayed. Select
No.
For Windows 2000
Double-click Computer, EPSON PJ_UD, and then
EMP_UDSE.EXE.
For Windows XP
Driver installation starts automatically.
For Windows Vista/Windows 7/Windows 8
When the dialog box is displayed, click Run EMP_UDSE.exe.
b
When the License Agreement screen is displayed, click Agree.
Projecting Images
c
d
Computer images are projected.
It may take a while before computer images are projected. Until
computer images are projected, leave the equipment as it is and do
not disconnect the USB cable or turn off the power to the projector.
Disconnect the USB cable when you finish projection.
When disconnecting the USB cable, there is no need to use Safely
Remove Hardware.
a
• If it is not installed automatically, double-click My Computer
- EPSON_PJ_UD - EMP_UDSE.EXE on your computer.
• If nothing is projected for some reason, click All Programs EPSON Projector - Epson USB Display - Epson USB
Display Vx.xx on your computer.
• When using a computer running Windows 2000 under user
authority, a Windows error message is displayed and you may
not be able to use the software. In this case, try updating
Windows to the latest version, restart, and then try to connect
again.
For more details, contact your local dealer or the nearest
address provided in the following document.
s Epson Projector Contact List
For Mac OS
a
Connect the computer's USB port to the projector's USB-B port
using a USB cable.
The Setup folder of USB Display is displayed in the Finder.
b
c
Double-click the USB Display Installer icon.
Follow the on-screen instructions to install.
38
d
When the License Agreement screen is displayed, click Agree.
Enter the administrator authority password and start the installation.
When the installation is complete, the USB Display icon is displayed
in the Dock and menu bar.
e
Computer images are projected.
f
When you finish projection, select Disconnect from the USB
Display icon menu on the menu bar or Dock, and then remove
the USB cable.
It may take a while before computer images are projected. Until
computer images are projected, leave the equipment as it is and do
not disconnect the USB cable or turn off the power to the projector.
a
• If the USB Display setup folder is not displayed automatically
in the Finder, double-click EPSON PJ_UD - USB Display
Installer on your computer.
• If nothing is projected for some reason, click the USB
Display icon in the Dock.
• If there is no USB Display icon in the Dock, double-click
USB Display from the Applications folder.
• If you select Exit from the USB Display icon menu on the
Dock, USB Display does not start automatically when you
connect the USB cable.
Projecting Images
Uninstalling
For Windows 2000
a
b
c
d
Click Start, select Settings, and then click Control Panel.
Double-click Add/Remove Programs.
Click Change or Remove Programs.
Select Epson USB Display and click Change/Remove.
For Windows XP
a
b
c
Click Start, and then click Control Panel.
Double-click Add or Remove Programs.
Select Epson USB Display and click Remove.
For Windows Vista/Windows 7
a
b
c
Click Start, and then click Control Panel.
Click Uninstall a program under Programs.
Select Epson USB Display and click Uninstall.
For Windows 8
a
b
c
Open Charms, and then select Search. Right-click (press and hold)
Epson USB Display Ver.XXX.
Select Uninstall from the app bar.
Select Epson USB Display, and then select Uninstall.
39
d
Follow the on-screen instructions to uninstall.
For Mac OS
a
b
Open the Applications folder, double-click USB Display, and then
double-click Tool.
Run USB Display UnInstaller.
Adjusting Projected Images
Correcting Keystone Distortion
40
• Correcting manually (Quick Corner)
Manually correct the four corners independently.
You can correct keystone distortion using one of the following methods.
• Correcting automatically (Auto V-Keystone)
Automatically corrects vertical keystone distortion.
• Correcting manually (H-Keystone Adjuster)
Manually corrects horizontal keystone distortion using the horizontal
keystone adjuster.
a
• Correcting manually (H/V-Keystone)
Manually correct distortion in the horizontal and vertical directions
independently.
When you correct keystone distortion, the projected image may be
reduced.
Adjusting Projected Images
Correcting automatically
Auto V-Keystone
When the projector detects any movement, for example when it is installed,
moved, or tilted, it automatically corrects vertical keystone distortion. This
function is called Auto V-Keystone.
When the projector remains still for about two seconds after it detects
movement, it displays a screen for adjustment and then automatically
corrects the projected image.
You can use Auto V-Keystone to correct the projected image under the
following conditions.
Correction angle: approx. 30˚ up and down
a
41
Correcting manually
You can manually correct keystone distortion.
You can use H/V-Keystone to correct the projected image under the
following conditions.
Correction angle: approx. 30˚ right and left/approx. 30˚ up and down
H-Keystone Adjuster
Move the horizontal keystone adjuster to the right or left to perform
horizontal keystone correction.
EB-X25/EB-W22/EB-X22
/EB-X21/EB-X20/EB-X17
• Auto V-Keystone works only when Projection is set to Front from
the Configuration menu.
s Extended - Projection p.89
• If you do not want to enable Auto V-Keystone, set Auto VKeystone to Off.
s Settings - Keystone - H/V-Keystone - Auto V-Keystone
p.88
EB-S21/EB-S17
a
• When using horizontal keystone adjuster, set H-Keystone Adjuster
to On.
s Settings - Keystone - H/V-Keystone - H-Keystone Adjuster
p.88
• You can also correct keystone distortion in the horizontal direction
using H/V-Keystone.
Adjusting Projected Images
42
H/V-Keystone
Manually correct distortion in the horizontal and vertical directions
independently.
a
Press the [w] or [v] button on the control panel during
projection to display the Keystone screen.
b
Press the following buttons to correct keystone distortion.
a
Press the [w] or [v] button to correct vertical distortion.
You can also set H/V-Keystone from the Configuration menu.
s Settings - Keystone - H/V-Keystone p.88
Quick Corner
This allows you to manually correct each of the four corners of the
projected image separately.
a
Press the [Menu] button while projecting.
s "Using the Configuration Menu" p.82
Using the remote control
Press the [a]/[b] buttons or the [Wide]/[Tele] buttons to correct
horizontal distortion.
Using the control panel
Adjusting Projected Images
b
Select Keystone from Settings.
c
Select Quick Corner, and then press the [
d
Using the [
], [
43
] button.
], [ ], and [ ] buttons on the remote control,
or the [w], [v], [a], and [b] buttons (or the [Wide]/[Tele] buttons)
on the control panel, select the corner to correct, and then press
the [ ] button.
Adjusting Projected Images
e
Using the [
], [
], [ ], and [ ] buttons on the remote control,
or the [w], [v], [a], and [b] buttons (or the [Wide]/[Tele] buttons)
on the control panel, correct the position of the corner.
When you press the [
displayed.
44
a
If the [Esc] button is held down for about two seconds while
the corner selection screen from step 4 is displayed, the
following screen is displayed.
] button, the screen shown in step 4 is
If the message "Cannot adjust any further." is displayed while
adjusting, you cannot adjust the shape any further in the direction
indicated by the gray triangle.
Reset Quick Corner: Resets the result of Quick Corner
corrections.
Switch to H/V-Keystone: Switches the correction method to
H/V-Keystone.
s "Settings Menu" p.88
Adjusting the Image Size
For EB-X25/EB-W22/EB-X22/EB-X21/EB-X20/EB-X17
Turn the zoom ring to adjust the size of the projected image.
f
Repeat procedures 4 and 5 as needed to adjust any remaining
corners.
For EB-S21/EB-S17
g
When you are done, press the [Esc] button to exit the correction
menu.
Wide: Enlarges the size of the projected image.
Because Keystone was changed to Quick Corner, the corner
selection screen shown in step 4 is displayed the next time you press
the [w] or [v] button on the control panel. Change Keystone to
H/V-Keystone if you want to perform horizontal and vertical
correction using the [w] or [v] button on the control panel.
s Settings - Keystone - H/V-Keystone p.88
Adjust by using the [Wide]/[Tele] buttons on the control panel.
Tele: Reduces the size of the projected image.
Adjusting Projected Images
EB-X25/EB-W22/EB-X22
/EB-X21/EB-X20/EB-X17
45
Adjusting the Horizontal Tilt
Extend and retract the rear feet to adjust the projector's horizontal tilt.
EB-S21/EB-S17
A Extend the rear foot.
B Retract the rear foot.
Adjusting the Image Position
Press the foot adjust lever to extend the front adjustable foot. You can
adjust the position of the image by tilting the projector up to 12 degrees.
Correcting the Focus
You can correct the focus using the focus ring.
EB-X25/EB-W22/EB-X22
/EB-X21/EB-X20/EB-X17
EB-S21/EB-S17
a
The larger the angle of tilt, the harder it becomes to focus. Install the
projector so that it only needs to be tilted at a small angle.
Adjusting Projected Images
Adjusting the Volume
You can adjust the volume using one of the following methods.
• Press the [Volume] button on the control panel or the remote control
to adjust the volume.
[a] Decreases the volume.
[b] Increases the volume.
Using the remote control
Using the control panel
(EB-X25/EB-W22/EB-X22/EB-X21/EB-X20/EB-X17
only)
• Adjust the volume from the Configuration menu.
s Settings - Volume p.88
Caution
Do not start at high volume.
A sudden excessive volume may cause loss of hearing. Always lower the volume
before powering off, so that you can power on and then gradually increase the
volume.
46
Selecting the Projection Quality (Selecting Color
Mode)
You can easily obtain the optimum image quality simply by selecting the
setting that best corresponds to your surroundings when projecting. The
brightness of the image varies depending on the mode selected.
Mode
Application
Dynamic
Ideal for use in a bright room. This is the brightest
mode, and reproduces shadow tones well.
Presentation
Ideal for making presentations using color materials
in a bright room.
Theatre
Ideal for watching films in a dark room. Gives
images a natural tone.
Photo*1
Ideal for projecting still pictures, such as photos, in
a bright room. The images are vivid and brought
into contrast.
Sports *2
Ideal for watching TV programmes in a bright
room. The images are vivid and brought to life.
sRGB
Ideal for images that conform to the sRGBg color
standard.
Blackboard
Even if you are projecting onto a blackboard
(greenboard), this setting gives your images a
natural tint, just like when projecting onto a screen.
Whiteboard
Ideal for making presentations using a whiteboard.
*1 This selection is only available when the input signal is RGB or when the
source is USB Display or USB.
*2 This selection is only available when the input signal is component video, or
when the input source is Video or S-Video.
Adjusting Projected Images
47
Each time you press the [Color Mode] button, the Color Mode name is
displayed on the screen and the Color Mode changes.
b
Select Auto Iris from Image.
c
Select Normal or High Speed.
Remote control
a
You can set Color Mode from the Configuration menu.
s Image - Color Mode p.85
Setting Auto Iris
a
By automatically setting the luminance according to the brightness of the
displayed image, it lets you enjoy deep and rich images.
a
Press the [Menu] button.
s "Using the Configuration Menu" p.82
Using the remote control
Using the control panel
The setting is stored for each Color Mode.
d
When set to High Speed, the brightness of the image is
adjusted as soon as the scene changes.
Press the [Menu] button to finish making settings.
a
Auto Iris can only be set when the Color Mode is Dynamic or
Theatre.
Changing the Aspect Ratio of the Projected Image
You can change the Aspect Ratiog of the projected image to suit the type,
the ratio of height and width, and the resolution of the input signals.
Adjusting Projected Images
48
Available aspect modes vary depending on the image signal currently being
projected.
Changing methods
Each time you press the [Aspect] button on the remote control, the aspect
mode name is displayed on the screen and the aspect ratio changes.
Remote control
a
You can set the aspect ratio from the Configuration menu.
s Signal - Aspect p.86
Changing the aspect mode
Projecting images from video equipment or from the HDMI port (for EB-W22)
Each time the [Aspect] button is pressed, the aspect mode changes in the
order Normal or Auto, 16:9, Full, Zoom, and Native.
Example: 1080p signal input (resolution: 1920x1080, aspect ratio: 16:9)
A
B
C
D
E
Normal or Auto
16:9
Full
Zoom
Native
Projecting images from video equipment (for EB-X25/EB-X22/EB-X21/EB-S21/EB-X20/
EB-X17/EB-S17)
Each time the [Aspect] button is pressed, the aspect mode changes in the
order 4:3 and 16:9.
When inputting a 720p/1080i signal and the aspect mode is set to 4:3, a 4:3
zoom is applied (the right and left sides of the image are cut off).
Example: 720p signal input (resolution: 1280x720, aspect ratio: 16:9)
Adjusting Projected Images
49
Projecting images from a computer
The following shows projection examples for each aspect mode.
For EB-W22
Aspect Mode
Input Signal
XGA 1024X768(4:3)
A 4:3
B 16:9
Projecting images from the HDMI port (for EB-X25/EB-X22/EB-X21/EB-S21/EB-X20/
EB-X17/EB-S17)
Normal
16:9
Each time the Aspect button is pressed, the aspect mode changes in the
order Auto, 4:3, and 16:9.
Example: 1080p signal input (resolution: 1920x1080, aspect ratio: 16:9)
Full
Zoom
A Auto
B 4:3
C 16:9
Native
WXGA 1280X800(16:10)
Adjusting Projected Images
50
For EB-X25/EB-X22/EB-X21/EB-S21/EB-X20/EB-X17/EB-S17
Aspect Mode
Input Signal
XGA 1024X768(4:3)
WXGA 1280X800(16:10)
Normal
4:3
16:9
a
If parts of the image are missing, set the Resolution setting to Wide
or Normal from the Configuration menu, according to the size of the
computer panel.
s Signal - Resolution p.86
Useful Functions
This chapter explains useful tips for giving presentations, and the Security functions.
Projection Functions
Projecting Without a Computer (PC Free)
Only EB-X21/EB-S21/EB-X17/EB-S17 are supported.
52
Type
File Type (Ex‐
tension)
Notes
Movie
.avi
• Cannot project images with a resolution greater
than 1280 x 720.
• The audio format can only playback linear PCM
and ADPCM.
By connecting a USB storage device such as a USB flash drives or a USB
hard disk to the projector, you can project the files stored on the device
without using a computer. This function is called PC Free.
a
• You may not be able to use USB storage devices that incorporate
security functions.
• You cannot correct keystone distortion while projecting in PC Free,
even if you press the [w] and [v] buttons on the control panel.
Specifications for files that can be projected using PC Free
Type
File Type (Ex‐
tension)
Notes
Image
.jpg
The following cannot be projected.
- CMYK color mode formats
- Progressive formats
- Images with a resolution greater than 8192 x 8192
Due to the characteristics of JPEG files, images may
not be projected clearly if the compression ratio is
too high.
.bmp
Cannot project images with a resolution greater
than 1280 x 800.
.gif
• Cannot project images with a resolution greater
than 1280 x 800.
• Cannot project animated GIFs.
.png
Cannot project images with a resolution greater
than 1280 x 800.
a
• When connecting and using a USB-compatible hard disk, make sure
you connect the AC adaptor supplied with the hard disk.
• The projector does not support some file systems, so use media that
has been formatted in Windows.
• Format the media in FAT16/32.
PC Free examples
Projecting images stored on USB storage
s "Projecting the selected image" p.55
s "Projecting image files in a folder in sequence (Slideshow)" p.56
Projection Functions
53
PC Free operating methods
Although the following steps are explained based on the remote control,
you can perform the same operations from the control panel.
Starting PC Free
a
• You can also insert a memory card into a USB card reader and then
connect the reader to the projector. However, some commercially
available USB card readers may not be compatible with the
projector.
• If the following screen (Select Drive screen) is displayed, press the
[
], [
], [ ], or [ ] buttons to select the drive you want to
use, and then press the [
a
Change the source to USB.
b
Connect the USB storage device to the projector.
] button.
s "Switching to the Target Image by Remote Control" p.36
s "Connecting USB Devices" p.27
PC Free starts and the file list screen is displayed.
• The following files are displayed as thumbnails (file contents are
displayed as small images).
- JPEG files
- AVI files (displays the image at the start of the movie)
• Other files or folders are displayed as icons as shown in the
following table.
Icon
File
Icon
File
JPEG files*
BMP files
GIF files
PNG files
AVI (Motion JPEG)
files*
*
When it cannot be displayed as a thumbnail, it is displayed as an icon.
• To display the Select Drive screen, position the cursor on Select
Drive at the top of the file list screen, and then press the [ ]
button.
Projection Functions
Projecting images
a
54
Rotating images
Press the [
], [
], [ ], or [ ] buttons to select the file or folder
you want to project.
You can rotate the played images in 90˚ increments. The rotating function
is also available during Slideshow.
a
b
a
While projecting, press the [
] or [
] button.
If not all of the files and folders are displayed on the current
screen, press the []] button on the remote control, or position
the cursor on Next Page at the bottom of the screen and press
the [ ] button.
To return to the previous screen, press the [[] button on the
remote control, or position the cursor on Previous Page at the
top of the screen and press the [ ] button.
b
Play images, or run Slideshow.
Press the [
] button.
The selected image is displayed.
When a folder is selected, the files in the selected folder are
displayed. To return to the previous screen, position the cursor on
Back to Top and press the [ ] button.
Stopping PC Free
To close PC Free, disconnect the USB device from the USB port on the
projector. For devices such as digital cameras or hard disks, turn off the
device and then remove it from the projector.
Projection Functions
55
Projecting the selected image
Attention
Do not disconnect the USB storage device while it is being accessed. PC Free
may not operate correctly.
a
a
Start PC Free.
The file list screen is displayed.
Press the [ ][ ] buttons to move to the next or previous
image file.
s "Starting PC Free" p.53
b
Press the [
], [
], [ ], and [ ] buttons to select the image file
you want to project.
d
To finish projecting, perform one of the following operations.
• Projecting an image: Press the [Esc] button.
• Projecting a movie: Press the [Esc] button to display the message
screen, select Exit, and then press the [ ] button.
When projection is finished, you are returned to the file list screen.
c
Press the [
] button.
The image is displayed or the movie is played back.
Projection Functions
Projecting image files in a folder in sequence (Slideshow)
You can project the image files in a folder in sequence, one at a time. This
function is called Slideshow. Use the following procedure to run
Slideshow.
a
To change files automatically when you run Slideshow, set Screen
Switching Time from Option in Slideshow to anything other than No.
The default setting is 3 seconds.
s "Image file display settings and Slideshow operation settings"
p.57
a
Start PC Free.
The file list screen is displayed.
s "Starting PC Free" p.53
b
Press the [
], [
], [ ], or [ ] buttons to position the cursor
over the folder for the Slideshow that you want to run, and then
press the [ ] button.
c
Select Slideshow at the bottom right of the file list screen, and
then press the [ ] button.
Slideshow starts, and the image files in the folder are automatically
projected in sequence, one at a time.
When the last file is projected, the file list is displayed again
automatically. If you set Continuous Play to On in the Option
window, projection starts again from the beginning when it reaches
the end.
s "Image file display settings and Slideshow operation settings"
p.57
You can proceed to the next screen, return to the previous screen, or
stop playback while projecting a Slideshow.
56
a
If Screen Switching Time on the Option screen is set to No, files do
not change automatically when you select Play Slideshow. Press the
[ ] button, the [
] button, or the []] button to continue to the
next file.
You can use the following functions when projecting a file with PC
Free.
• Freeze
s "Freezing the Image (Freeze)" p.58
• A/V Mute
s "Hiding the Image and Sound Temporarily (A/V Mute)" p.57
• E-Zoom
s "Enlarging Part of the Image (E-Zoom)" p.59
• Pointer
s "Pointer Function (Pointer)" p.58
Projection Functions
57
Image file display settings and Slideshow operation settings
You can set the file display order and Slideshow operations on the Option
screen.
a
Select Option at the bottom of the file list screen, and then press
the [ ] button.
b
When the following Option screen is displayed, set each of the
items.
Select any of the options as necessary and press the [
] button.
The following table shows the details for each item.
c
Screen Switch‐
ing Time
You can set the time for a single file to be displayed in
Slideshow. You can set a time between No (0) to 60
Seconds. When you set Off, auto play is disabled.
Effect
You can set the screen effects when changing slides.
When you have finished making settings, use the [
], [
], [ ],
or [ ] buttons to position the cursor over OK, and then press the
[
] button.
The settings are applied.
If you do not want to apply the settings, position the cursor on
Cancel, and then press the [ ] button.
Hiding the Image and Sound Temporarily (A/V
Mute)
You can use this when you want to focus the audience's attention on what
you are saying, or if you do not want to show details such as when you are
changing between files during presentations from a computer.
Display Order
You can select to display the files in Name Order or Date
Order.
Sort Order
You can select to sort the files In Ascending or In
Descending order.
Continuous
Play
You can set whether to repeat the Slideshow.
Projection Functions
58
Each time you press the [A/V Mute] button or open/close the lens cover,
A/V Mute turns on or off.
Remote control
Projector
Freezing the Image (Freeze)
When Freeze is activated on moving images, the frozen image continues to
project on the screen, so you can project a moving image one frame at a
time like a still photo. Also, you can perform operations such as changing
between files during presentations from a computer without projecting any
images if the Freeze function is activated beforehand.
Each time you press the [Freeze] button, Freeze turns on or off.
Remote control
a
• When projecting moving images, the images and sound continue to
be played back while A/V Mute is on. It is not possible to resume
projection from the point where A/V Mute was activated.
• You can select the screen displayed when the [A/V Mute] button is
pressed from the Configuration menu.
s Extended - Display - A/V Mute p.89
• When A/V mute is enabled with the [A/V Mute] button, A/V Mute
Timer activates and the power is automatically turned off after
approximately 30 minutes. If you do not want to enable A/V Mute
Timer, set A/V Mute Timer to Off.
s ECO - A/V Mute Timer p.99
• When the A/V mute slide is closed for approximately 30 minutes,
Lens Cover Timer activates and the power is automatically turned
off. If you do not want Lens Cover Timer to activate, set Lens Cover
Timer to Off.
s ECO - Lens Cover Timer p.99
• The lamp is still lit during A/V Mute, so the lamp hours continue to
accumulate.
a
• Audio does not stop.
• When projecting moving images, the images continue to be played
back while the screen is frozen. It is not possible to resume
projection from the point where the screen was frozen.
• If the [Freeze] button is pressed while the Configuration menu or
the Help screen is displayed, the menu or the Help screen that is
displayed is closed.
• Freeze still works while E-Zoom is being used.
Pointer Function (Pointer)
This allows you to move a Pointer icon on the projected image, and helps
you draw attention to the area you are talking about.
Projection Functions
59
a
You can select the shape of the pointer icon from the
Configuration menu.
s Settings - Pointer Shape p.88
Enlarging Part of the Image (E-Zoom)
a
Display the Pointer.
Each time you press the [Pointer] button, the pointer appears or
disappears.
This is useful when you want to expand images to see them in greater
detail, such as graphs and tables.
Remote control
a
b
Move the Pointer icon (
).
Remote control
When any pair of adjacent [
], [
], [ ], or [ ] buttons are
pressed at the same time, the pointer can be moved diagonally.
Start E-Zoom.
Press the [z] button to display the Cross (
Remote control
).
Projection Functions
b
Move the Cross (
60
) to the area of the image that you want to
enlarge.
Remote control
Using the Remote Control to Operate the Mouse
Pointer (Wireless Mouse)
You can control the computer's mouse pointer from the projector's remote
control. This function is called Wireless Mouse.
The following operating systems are compatible with Wireless Mouse.
Windows
Windows
Windows
Windows
Windows
Windows
OS
When any pair of adjacent [
], [
], [ ], or [ ] buttons are
pressed at the same time, the pointer can be moved diagonally.
c
*
Enlarge.
Remote control
[z] button: Expands the area each time
it is pressed. You can expand quickly by
holding the button down.
[x] button: Reduces images that have
been enlarged.
[Esc] button: Cancels E-Zoom.
Mac OS
2000
XP
Vista
7
8
Mac
Mac
Mac
Mac
Mac
Mac
OS
OS
OS
OS
OS
OS
X
X
X
X
X
X
10.3.x
10.4.x
10.5.x
10.6.x
10.7.x
10.8.x
It may not be possible to use the Wireless Mouse function under some
versions of the operating systems.
Use the following procedure to enable the Wireless Mouse function.
a
Connect the projector to the computer with the USB cable.
s "Connecting a Computer" p.25
the source to one of the following.
b •Change
USB Display
• Computer
a
• The enlargement ratio appears on the screen. The selected
area can be enlarged to between 1 to 4 times in 25
incremental steps.
• During enlarged projection, press the [
[ ] buttons to scroll the image.
], [
], [ ], or
• HDMI
s "Switching to the Target Image by Remote Control" p.36
Projection Functions
61
Once set, the mouse pointer can be controlled as follows.
a
Moving the mouse pointer
[
][
][ ][ ] buttons:
• When any pair of adjacent [
], [
], [ ], or [ ] buttons are
pressed at the same time, the pointer can be moved diagonally.
• If the mouse button settings are set to reverse on the computer, the
operation of the remote control buttons will also be reversed.
Moves the mouse pointer.
• The Wireless Mouse function does not work under the following
conditions.
- When the Configuration menu or a Help screen is displayed
- When operating functions other than the Wireless Mouse function
(such as adjusting the volume)
However, when using the E-Zoom or Pointer function, the page up
or down function is available.
Mouse clicks
[Esc] button: Right click.
[ ] button: Left click. Press quickly
twice to double-click.
Saving a User's Logo
You can save the image that is currently being projected as a User's Logo.
Drag and drop
While holding down the [
press the [
], [
] button,
], [ ], or [ ]
button.
Release the [ ] button to drop at the
desired location.
a
a
Once a User's Logo has been saved, the logo cannot be returned to the
factory default.
Project the image you want to save as the User's Logo, and then
press the [Menu] button.
s "Using the Configuration Menu" p.82
Page Up/Down
[[] button: Moves to the previous page.
[]] button: Moves to the next page.
Using the remote control
Using the control panel
Projection Functions
b
Select User's Logo from Extended.
62
d
Move the box to select the part of the image to use as the User's
Logo.
You can perform the same operations from the projector's control
panel.
Remote control
a
a
• When User's Logo Protect from Password Protect is set to
On, a message is displayed and the User's Logo cannot be
changed. You can make changes after setting User's Logo
Protect to Off.
s "Managing Users (Password Protect)" p.65
• If User's Logo is selected when Keystone, E-Zoom, Aspect, or
Adjust Zoom are being performed, the function currently
being performed is temporarily cancelled.
c
When the message "Choose this image as the User's Logo?" is
displayed, select Yes.
a
When you press the [ ] button on the remote control or the
control panel, the screen size may change depending on the
signal to match the actual resolution of the image signal.
You can save at 400x300 dots in size.
e
When you press the [ ] button and the message "Select this
image?" is displayed, select Yes.
f
Select the zoom factor from the zoom setting screen.
Projection Functions
g
63
When the message "Save this image as the User's Logo?" is
displayed, select Yes.
The image is saved. After the image has been saved, the message
"Completed." is displayed.
a
• When a User's Logo is saved, the previous User's Logo is
erased.
• It takes a while to save. Do not operate the projector or any
connected equipment while it is saving, otherwise
malfunctions may occur.
Saving User Pattern
You can save the image that is currently being projected as a User Pattern.
a
a
c
Select User Pattern.
When a User Pattern is saved, the previous User Pattern is erased.
Project the image you want to use as the User Pattern, and then
press the [Menu] button.
s "Using the Configuration Menu" p.82
Using the remote control
Using the control panel
a
b
Select Pattern from Settings.
If User Pattern is selected when one of the Keystone, E-Zoom,
Aspect, Progressive, and Zoom Adjustment functions is being
used, the function currently being used is cancelled temporarily.
Projection Functions
d
When "Do you want to use the currently projected image as the
User Pattern?" is displayed, select Yes.
e
When you press the [Enter] button, the message "Do you save this
image as the User Pattern?" is displayed. Then, select Yes.
The image is saved. After the image has been saved, the message
"The User Pattern setting is complete". is displayed.
a
• Once a User Pattern has been saved, User Pattern cannot be
returned to the factory default.
• Saving the User Pattern may take approximately 15 seconds.
Do not operate the projector or any connected equipment
while it is saving, otherwise malfunctions may occur.
64
Security Functions
The projector has the following enhanced security functions.
• Password Protect
You can limit who can use the projector.
• Control Panel Lock
You can prevent people changing the settings on the projector without
permission.
s "Restricting Operation (Control Panel Lock)" p.67
• Anti-Theft Lock
The projector is equipped with the following anti-theft security device.
s "Anti-Theft Lock" p.69
Managing Users (Password Protect)
When Password Protect is activated, people who do not know the password
cannot use the projector to project images even if the projector power is on.
Furthermore, the user's logo that is displayed when you turn on the
projector cannot be changed. This acts as an anti-theft function as the
projector cannot be used even if it is stolen. At the time of purchase,
Password Protect is not activated.
Kinds of Password Protect
The following two kinds of Password Protect settings can be made
according to how the projector is being used.
• Power On Protect
When Power On Protect is On, you need to enter a preset password after
the projector is plugged in and turned on (this also applies to Direct
Power On). If the correct password is not entered, projection does not
start.
65
• User's Logo Protection
Even if someone tries to change the User's Logo set by the owner of the
projector, it cannot be changed. When User's Logo Protect is set to On,
the following setting changes for the User's Logo are prohibited.
• Capturing a User's Logo
• Setting Display Background, Startup Screen, or A/V Mute from
Display
s Extended - Display p.89
• Network Protection
When Network Protect is set to On, changing the settings for Network is
prohibited.
s "Network Menu" p.91
Setting Password Protect
Use the following procedure to set Password Protect.
a
During projection, hold down the [Freeze] button for about five
seconds.
The Password Protect setting menu is displayed.
Remote control
Security Functions
a
66
• If Password Protect is already activated, you must enter the
password.
If the password is entered correctly, the Password Protect
setting menu is displayed.
s "Entering the Password" p.66
(2)
(3)
• When the password is set, stick the password protect sticker
in a visible position on the projector as a further theft
deterrent.
s Password Protect Sticker
b
When the message "Change the password?" is displayed, select Yes and
then press the [ ] button. The default password is set to "0000". Change
this to your own desired Password. If you select No, the screen displayed
in step 2 is displayed again.
While holding down the [Num] button, enter a four digit number using
the numeric buttons. The number entered is displayed as "* * * *". When
you enter the fourth digit, the confirmation screen is displayed.
Remote control
Select the type of Password Protect you want to set, and then
press the [ ] button.
(4)
Re-enter the password.
"The message Password accepted." is displayed.
If you enter the password incorrectly, a message is displayed prompting
you to re-enter the password.
Entering the Password
c
Select On, and then press the [
d
Set the password.
] button.
Press the [Esc] button, the screen displayed in step 2 is displayed
again.
(1)
Select Password, and then press the [
] button.
When the password entry screen is displayed, enter the password using the
remote control.
While holding down the [Num] button, enter the password by pressing the
numeric buttons.
Security Functions
67
Restricting Operation (Control Panel Lock)
Perform one of the following to lock the operation buttons on the control
panel.
• Full Lock
All of the buttons on the control panel are locked. You cannot perform
any operations from the control panel, including turning the power on or
off.
When you enter the correct password, Password Protect is temporarily
released.
Attention
• If an incorrect password is entered three times in succession, the message
"The projector's operation will be locked." is displayed for approximately five
minutes, and then the projector switches to standby mode. If this happens,
disconnect the power plug from the electrical outlet and then reinsert it and
turn the projector's power back on. The projector displays the password entry
screen again so that you can enter the correct password.
• If you have forgotten the password, make a note of the "Request Code:
xxxxx" number that appears on the screen and contact the nearest address
provided in the Epson Projector Contact List.
s Epson Projector Contact List
• If you continue to repeat the above operation and enter the wrong password
thirty times in succession, the following message is displayed and the
projector does not accept any more password entries. "The projector's
operation will be locked. Contact Epson as described in your documentation."
s Epson Projector Contact List
• Partial Lock
All of the buttons on the control panel, except for the [t] power button,
are locked.
This is useful at events or shows when you want to deactivate all buttons
during projection or at schools when you want to limit button operation.
The projector can still be operated using the remote control.
a
Press the [Menu] button while projecting.
s "Using the Configuration Menu" p.82
Using the remote control
Using the control panel
Security Functions
b
Select Control Panel Lock from Settings.
68
a
You can release the control panel lock by one of the following
two methods.
• Select Off from Control Panel Lock.
s Settings - Control Panel Lock p.88
• Press and hold down the [ ] button on the control panel
for about seven seconds, a message is displayed and the lock
is released.
c
Select either Full Lock or Partial Lock according to your purpose.
d
Select Yes when the confirmation message is displayed.
The control panel buttons are locked according to the setting you
chose.
Security Functions
Anti-Theft Lock
The projector is equipped with the following types of anti-theft security
devices.
• Security slot
The security slot is compatible with the Microsaver Security System
manufactured by Kensington.
See the following for more details on the Microsaver Security System.
s http://www.kensington.com/
• Security cable installation point
A commercially available theft-prevention wire lock can be passed
through the installation point to secure the projector to a desk or pillar.
Installing the wire lock
Pass an anti-theft wire lock through the installation point.
See the documentation supplied with the wire lock for locking instructions.
69
Monitoring and Controlling
EasyMP Monitor
By using EasyMP Monitor, you can display the status of multiple Epson
network projectors on your computer. This allows you to check the status
of the projectors and control them from your computer. The Message
Broadcasting plugin for EasyMP Monitor can be used to simultaneously
send JPEG files to registered projectors. You can download EasyMP
Monitor from the following Web site.
http://www.epson.com
Download the Message Broadcasting plugin from the Web site.
Changing Settings Using a Web Browser (Web
Control)
By using a Web browser of a computer connected to the projector on a
network, you can make settings and control the projector. This function
allows you to perform setup and control operations remotely. In addition,
since you can use the computer's keyboard, entering characters required for
the setup is easier.
Use Microsoft Internet Explorer 8.0 or later as the Web browser. If using a
Mac OS X, use Safari.
a
If you set Standby Mode to Communication On, you can use the
Web browser to make settings and perform control even if the
projector is in standby mode (when the power is off).
s ECO - Standby Mode p.99
70
Projector setup
In a Web browser, you can set items that are usually set in the projector's
Configuration menu. The settings are reflected in the Configuration menu.
There are also items that can only be set in the Web browser.
Items in the Configuration menu that cannot be set by the Web browser
• Settings Menu - Pointer Shape
• Settings Menu - Pattern
• Settings Menu - User Button
• Extended Menu - User's Logo
• Extended Menu - Language
• Extended Menu - Operation - High Altitude Mode
• Reset Menu - Reset All and Reset Lamp Hours
The settings for items on each menu are the same as the projector's
Configuration menu.
s "Configuration Menu" p.81
Items that can only be set with a Web browser
• SNMP Community Name (up to 32 single-byte alphanumeric characters)
• Monitor Password (up to 16 single-byte alphanumeric characters)
Displaying the Web Control screen
Use the following procedure to display the Web Control screen.
Make sure the computer and projector are connected to the network. When
communicating with a wireless LAN, connect in Advanced mode.
a
If your Web browser is set up to connect via a proxy server, the Web
Control screen cannot be displayed. To display Web Control, you need
to make settings so that a proxy server is not used for a connection.
Monitoring and Controlling
a
b
71
Start a Web browser on the computer.
Enter the IP address of the projector in the address input box of
the Web browser, and press the Enter key on the computer's
keyboard.
The Web Control screen is displayed.
When Web Control Password is set from the Configuration menu,
the password entry screen is displayed.
c
c
The Web Remote screen is displayed.
Enter the user ID and password.
Enter "EPSONWEB" as the user ID.
The initial password is "admin".
a
• Enter the user ID even if a password has not been set. You
cannot change the user ID.
• You can change the password on the Network menu from the
Configuration menu.
s Network - Basic - Web Control Password p.93
Displaying the Web Remote screen
The Web Remote function allows you to perform projector remote control
operations with a Web browser.
a
b
Display the Web Control screen.
Name
Function
A Power button
[t]
Turns the projector power on or off.
s "From Installation to Projection" p.34
B [Computer] button
Each time you press the button, the input changes between
images from the Computer1 port and the Computer2
port.
C [Video] button
Each time the button is pressed, the image cycles through
the Video, S-Video, and HDMI ports.
D [Freeze] button
Images are paused or unpaused.
s "Freezing the Image (Freeze)" p.58
Click Web Remote.
Monitoring and Controlling
Name
72
Function
E [A/V Mute] button
Turns the video and audio on or off.
s "Hiding the Image and Sound Temporarily (A/V
Mute)" p.57
F [Page] buttons
[[][]]
Changes pages in files such as PowerPoint files when using
the following projection methods.
• When using the Wireless Mouse function
s "Using the Remote Control to Operate the
Mouse Pointer (Wireless Mouse)" p.60
• When using USB Display
s "Projecting with USB Display" p.36
• During a network connection
When projecting images or scenarios using PC Free,
pressing these buttons displays the previous/next screen.
G [Source Search]
button
Changes to the next input source that is sending an image.
s "Automatically Detect Input Signals and Change the
Projected Image (Source Search)" p.35
H [LAN] button
Changes to the image projected with EasyMP Network
Projection. When projecting using the optional Quick
Wireless Connection USB Key, this button switches to
that image.
s "Switching to the Target Image by Remote Control"
p.36
I [USB] button
J [Volume] buttons
[a][b]
Each time the button is pressed, it cycles through the
following images:
• USB Display
• Images from the device connected to the USB port
s "Switching to the Target Image by Remote Control"
p.36
[a] Decreases the volume.
[b] Increases the volume.
s "Adjusting the Volume" p.46
Using the Mail Notification Function to Report
Problems
When you set Mail Notification, notification messages are sent to the preset
email addresses when a problem or warning occurs with a projector. This
will enable the operator to be notified of problems with projectors even at
locations away from the projectors.
s Network - Mail - Mail Notification p.97
a
• Up to a maximum of three notification destinations (addresses) can
be registered, and notification messages can be sent to all three
destinations at once.
• If a projector develops a critical problem and suddenly stops
working, it may not be able to send a message notifying an operator
of the problem.
• If you set Standby Mode to Communication On, you can control
the projector even if it is in standby mode (when the power is
off).
s ECO - Standby Mode p.99
Reading Error Notification Mail
When the Mail Notification function is set to On and a problem or warning
occurs in the projector, the following email will be sent.
Mail sender: Address for Address 1
Subject: EPSON Projector
Line 1: The projector name where the problem has occurred
Line 2: The IP address set for the projector where the problem has
occurred.
Line 3 and on: Details of the problem
Monitoring and Controlling
The details of the problem are listed line by line. The messages are listed
below.
• Internal error
• Fan related error
• Sensor error
• Lamp cover is open
• Lamp timer failure
73
a
• SNMP should be managed by a network administrator or someone
who is familiar with the network.
• To use the SNMP function to monitor the projector, you need to
install the SNMP manager program on your computer.
• The SNMP Agent for this projector complies with version 1
(SNMPv1).
• The managing function using SNMP cannot be used via wireless
LAN in Quick mode.
• Up to two destination IP addresses can be saved.
• Lamp out
• Internal temperature error
• High-speed cooling in progress
• Lamp replacement notification
• No-signal
No Signal is input to the projector. Check the connection status or check
that the power for the signal source is turned on.
• Auto Iris Error
• Power Err. (Ballast)
See the following to deal with problems or warnings.
s "Reading the Indicators" p.104
Management Using SNMP
By setting SNMP to On in the Configuration menu, notification messages
are sent to the specified computer when a problem or warning occurs. This
will enable the operator to be notified of problems with projectors even at
locations away from the projectors.
s Network - Others - SNMP p.98
ESC/VP21 Commands
You can control the projector from an external device using ESC/VP21.
Command list
When the power ON command is transmitted to the projector, the power
turns on and it enters warm-up mode. When the projector's power has
turned on, a colon ":" (3Ah) is returned.
When a command is input, the projector executes the command and
returns a ":", and then accepts the next command.
If the command being processed terminates abnormally, an error message is
output and a ":" is returned.
Item
Power ON/OFF
Signal selection
Command
On
PWR ON
Off
PWR OFF
Computer1
Computer2
Auto
SOURCE 1F
RGB
SOURCE 11
Component
SOURCE 14
Auto
SOURCE 2F
Monitoring and Controlling
74
Item
A/V Mute On/Off
A/V Mute selection
Command
RGB
SOURCE 21
Component
SOURCE 24
HDMI
SOURCE 30
Video
SOURCE 41
S-Video
SOURCE 42
USB Display
SOURCE 51
USB
SOURCE 52
LAN
SOURCE 53
On
MUTE ON
Off
MUTE OFF
Black
MSEL 00
Blue
MSEL 01
Logo
MSEL 02
• Projector input port name: RS-232C
<At the projector>
<At the computer>
<At the projector>
(PC serial cable)
Add a Carriage Return (CR) code (0Dh) to the end of each command and
transmit.
For more details, contact your local dealer or the nearest address provided
in the Epson Projector Contact List.
s Epson Projector Contact List
Cable layouts
Serial connection
• Connector shape: D-Sub 9-pin (male)
Signal Name
Function
GND
Signal wire ground
TD
Transmit data
RD
Receive data
Communications protocol
•
•
•
•
•
Default baud rate setting: 9600 bps
Data length: 8 bit
Parity: None
Stop-bit: 1 bit
Flow control: None
<At the computer>
Monitoring and Controlling
75
About PJLink (EB-X25/EB-W22/EB-X22/EB-X20
Only)
PJLink Class1 was established by the JBMIA (Japan Business Machine and
Information System Industries Association) as a standard protocol for
controlling network-compatible projector's as part of their efforts to
standardize projector control protocols.
The projector complies with the PJLink Class1 standard established by the
JBMIA.
See the Network menu for more information on PJLink network settings.
s "Network Menu" p.91
It complies with all commands except for the following commands defined
by PJLink Class1, and agreement was confirmed by the PJLink standard
adaptability verification.
URL:http://pjlink.jbmia.or.jp/english/
• Non-compatible commands
Function
Mute settings
PJLink Command
Image muting set
AVMT 11
Audio muting set
AVMT 21
• Input names defined by PJLink and corresponding projector sources
Source
PJLink Command
Source
PJLink Command
USB
INPT 41
LAN
INPT 52
USB Display
INPT 53
• Manufacturer name displayed for "Manufacture name information query"
EPSON
• Model name displayed for "Product name information query"
EPSON 25
EPSON 22
EPSON 20
® (EB-X25/EB-W22/EB-
About Crestron RoomView
X22/EB-X20 only)
®
Crestron RoomView is an integrated control system provided by
Crestron . It can be used to monitor and control multiple devices
connected on a network.
®
The projector supports the control protocol, and can therefore be used in a
system built with Crestron RoomView .
Visit the Crestron
®
®
®
Web site for details on Crestron RoomView .
http://www.crestron.com
Computer1
INPT 11
Computer2
INPT 12
The following provides an overview of Crestron RoomView .
Video
INPT 21
S-Video
INPT 22
HDMI
INPT 32
• Remote operation using a Web browser
You can operate a projector from your computer just like using a remote
control.
®
Monitoring and Controlling
76
• Monitoring and control with application software
You can use Crestron RoomView Express or Crestron RoomView
Server Edition provided by Crestron to monitor devices in the system,
to communicate with the help desk, and to send emergency messages. See
the following Web site for details.
http://www.crestron.com/getroomview
®
®
®
This manual describes how to perform operations on your computer using
a Web browser.
a
a
b
Start a Web browser on the computer.
Enter the IP address of the projector in the address field of the
Web browser, and press the Enter key on the keyboard.
The operation window is displayed.
Using the operation window
• You can only enter single-byte alphanumeric characters and symbols.
• The following functions cannot be used while using Crestron
RoomView .
s "Changing Settings Using a Web Browser (Web Control)"
p.70
Message Broadcasting (EasyMP Monitor plug-in)
®
• If you set Standby Mode to Communication On, you can control
the projector even if it is in standby mode (when the power is
off).
s ECO - Standby Mode p.99
Operating a projector from your computer
A You can perform the following operations when you click the buttons.
Displaying the operation window
Check the following before carrying out any operations.
• Make sure the computer and projector are connected to the network.
When communicating with a wireless LAN, connect in Advanced mode.
s "Wireless LAN menu (EB-X21/EB-S21/EB-X17/EB-S17 only)" p.93
• Set Crestron RoomView to On from the Network menu.
s Network - Others - Crestron RoomView p.84
Button
Function
Power
Turns the projector power on or off.
Vol-/Vol+
Adjusts the volume.
Monitoring and Controlling
Button
77
Function
A/V Mute
Button
Turns the video and audio on or off.
s "Hiding the Image and Sound Temporarily (A/V
Mute)" p.57
B Switch to the image from the selected input source. To display input sources that
are not shown in Source List, click (a) or (b) to scroll up or down.
You can change the source name if necessary.
C You can perform the following operations when you click the buttons. To display
buttons that are not shown in Source List, click (c) or (d) to scroll left or right.
Button
Images are paused or unpaused.
s "Freezing the Image (Freeze)" p.58
Contrast
You can adjust the difference between light and dark in
the images.
Brightness
You can adjust the image brightness.
Color
You can adjust the color saturation for the images.
Sharpness
You can adjust the image sharpness.
Zoom
Click the [z] button to enlarge the image without
changing the projection size. Click the [x] button to
reduce an image that was enlarged with the [z] button.
Click the [ ], [ ], [ ], or [ ] buttons to change the
position of an enlarged image.
s "Enlarging Part of the Image (E-Zoom)" p.59
D The [
[
], [
OK
Performs the same operation as the [
remote control.
s "Remote Control" p.16
Menu
Displays and closes the Configuration menu.
Auto
If clicked while projecting analog RGB signals from
Computer1 port or Computer2 port, automatically
optimizes the image by adjusting the Tracking, Sync.,
and Position.
Search
Changes to the next input source that is sending an
image.
s "Automatically Detect Input Signals and Change the
Projected Image (Source Search)" p.35
Esc
Performs the same operation as the [Esc] button on the
remote control.
s "Remote Control" p.16
Function
Freeze
], [
], and [
] buttons perform the same operations as the [
], [ ], and [ ] buttons on the remote control. You can perform the
following operations when you click the other buttons.
Function
] button on the
E You can perform the following operations when you click the tabs.
Tab
],
Function
Contact IT Help
Displays the Help Desk window. Used to send messages
to, and receive messages from, the administrator using
Crestron RoomView Express.
Info
Displays information on the projector that is currently
connected.
Tools
Changes settings in the projector that is currently
connected. See the next section.
®
Using the tools window
The following window is displayed when you click the Tools tab on the
operation window. You can use this window to change settings in the
projector that is currently connected.
Monitoring and Controlling
78
Item
A Crestron Control
Make settings for Crestron central controllers.
®
B Projector
The following items can be set.
Item
Select the Enabled check box to use DHCP. You cannot
enter an IP address if DHCP is enabled.
IP Address
Enter the IP address to assign to the currently connected
projector.
Subnet Mask
Enter a subnet mask for the currently connected
projector.
Default Gateway
Enter the gateway address for the currently connected
projector.
Send
Click this button to confirm the changes made to the
Projector.
C Admin Password
Select the Enabled check box to require a password to open the Tools window.
The following items can be set.
Location
Enter an installation location name for the projector
that is currently connected on the network. (The name
can contain up to 32 single-byte alphanumeric
characters and symbols.)
Enter a user name for the projector. (The name can
contain up to 32 single-byte alphanumeric characters
and symbols.)
Function
New Password
Enter the new password when changing the password to
open the Tools window. (The name can contain up to 26
single-byte alphanumeric characters.)
Confirm
Enter the same password as you entered in New
Password. If the passwords are not the same, an error is
displayed.
Send
Click this button to confirm the changes made to the
Admin Password.
Function
Enter a name to differentiate the projector that is
currently connected from other projectors on the
network. (The name can contain up to 15 single-byte
alphanumeric characters.)
Assigned To
DHCP
Item
Projector Name
Function
D User Password
Select the Enabled check box to require a password to open the operation window
on the computer.
The following items can be set.
Monitoring and Controlling
Item
79
Function
New Password
Enter the new password when changing the password to
open the operation window. (The name can contain up
to 26 single-byte alphanumeric characters.)
Confirm
Enter the same password as you entered in New
Password. If the passwords are not the same, an error is
displayed.
Send
Click this button to confirm the changes made to the
User Password.
About Event ID
80
Check the numbers and then apply the following countermeasures. If you cannot resolve the problem, contact your network administrator, or contact your local
dealer or the nearest address provided in the Epson Projector Contact List.
s Epson Projector Contact List
Event ID
Cause
Remedy
0432
0435
Failed to startup EasyMP Network Projection.
Restart the projector.
0434
0481
0482
0485
Network communication is unstable.
Check the network communication status, and reconnect after waiting for a
while.
0433
Cannot play transferred images.
Restart EasyMP Network Projection.
0484
Communication was disconnected from the computer.
0483
04FE
EasyMP Network Projection ended unexpectedly.
Check the network communication status, and then restart the projector.
0479
04FF
A system error occurred in the projector.
Restart the projector.
0891
Cannot find an access point with the same SSID.
Set the computer, the access point, and the projector to the same SSID.
0892
The WPA/WPA2 authentication type does not match.
0893
The WEP/TKIP/AES encryption type does not match.
Check that the wireless LAN security settings are correct.
s Security p.95
0894
Communication was disconnected because the projector connected to an
unauthorized access point.
Contact your network administrator for more information.
0898
Failed to acquire DHCP.
Check that the DHCP server is operating correctly. If you are not using DHCP,
turn off the DHCP setting.
s Wireless LAN - IP Settings p.93
0899
Other communication errors
If restarting the projector or EasyMP Network Projection does not solve the
problem, contact your local dealer or the nearest address provided in the Epson
Projector Contact List.
s Epson Projector Contact List
Configuration Menu
This chapter explains how to use the Configuration menu and its functions.
Using the Configuration Menu
This section explains how to use the Configuration menu.
Although steps are explained using the remote control as an example, you
can perform the same operations from the control panel. Check the guide
under the menu for the available buttons and their operations.
a
b
82
c
Select a submenu item.
d
Change settings.
e
Press the [Menu] button to finish making settings.
Display the Configuration menu screen.
Select a top menu item.
List of Functions
83
Top Menu Name
Configuration Menu Table
Settable items vary depending on the model being used and the image
signal and source being projected.
Top Menu Name
Image menu
s p.85
Signal menu
s p.86
Submenu Name
Color Mode
Items or Setting Values
Dynamic, Presentation, Theatre,
Photo, Sports, sRGB, Blackboard,
and Whiteboard
Submenu Name
Items or Setting Values
Video Signal
Auto, NTSC, NTSC4.43, PAL,
M-PAL, N-PAL, PAL60, and
SECAM
Aspect
Normal, Auto, 4:3, 16:9, Full,
Zoom, and Native
Overscan
Auto, Off, 4%, and 8%
Image Processing
Fine, Fast
Keystone
H/V-Keystone and Quick Corner
-
Brightness
-24 - 24
Contrast
-24 - 24
Color Saturation
-32 - 32
Zoom
(EB-S21/EB-S17 only)
Tint
-32 - 32
Control Panel Lock
Full Lock, Partial Lock, and Off
Sharpness
-5 - 5
Pointer Shape
Pointer 1, 2, and 3
Abs. Color Temp.
5000K to 10000K
Volume
0 - 10
Color Adjustment
Red: -16 to 16
Green: -16 to 16
Blue: -16 to 16
Remote Receiver
Front/Rear, Front, Rear, and Off
User Button
Power Consumption, Info,
Progressive, Resolution, and
Pattern Display
Pattern
Pattern Display, Pattern Type,
User Pattern, and Test Pattern
Display
Messages, Display Background,
Startup Screen, and A/V Mute
Settings menu
s p.88
Auto Iris
Off, Normal, High Speed
Auto Setup
On and Off
Resolution
Auto, Wide, and Normal
Tracking
-
Sync.
0 - 31
User's Logo
-
Position
Up, Down, Left, and Right
Projection
Progressive
Off, Video, and Film/Auto
Front, Front/Ceiling, Rear, and
Rear/Ceiling
Noise Reduction
Off, NR1, and NR2
Operation
HDMI Video Range
Auto, Normal, and Expanded
Direct Power On, High Altitude
Mode, Startup Source Search
Input Signal
Auto, RGB, and Component
A/V Settings
A/V Output, Audio Output,
HDMI Audio Output
Language
15 or 36 languages*1
Power Consumption
Normal and ECO
Extended menu
s p.89
ECO menu
List of Functions
Top Menu Name
s p.99
Info menu
s p.100
Reset menu
s p.101
84
Submenu Name
Items or Setting Values
Light Optimizer
On and Off
Sleep Mode
On and Off
Sleep Mode Timer
0 - 30
Lens Cover Timer
On and Off
A/V Mute Timer
On and Off
Standby Mode
Communication On and
Communication Off
Network menu
Top Menu Name
Basic menu
s p.93
Submenu Name
Setting Values
Projector Name
-
PJLink Password
(EB-X25/EB-W22/EBX22/EB-X20 only)
-
Web Control Password
-
Projector Keyword
On and Off
Wireless LAN Power
On and Off
Connection Mode
Quick, Advanced
Channel
1ch, 6ch, 11ch
Wireless LAN Sys.
802.11b/g and 802.11b/g/n
ECO Display
On and Off
Lamp Hours
-
Source
-
Input Signal
-
Resolution
-
SSID Auto Setting
On and Off
Video Signal
-
SSID
-
Refresh Rate
-
IP Settings
Sync Info
-
DHCP, IP Address, Subnet Mask,
and Gateway Address
Status
-
SSID Display
On and Off
Serial Number
-
IP Address Display
On and Off
Version
-
Security
Event ID
-
No, WEP, WPA-PSK, and WPA2PSK
Reset All
-
WEP Encryption
128Bit and 64Bit
Reset Lamp Hours
-
Format
ASCII and HEX
Key ID
1, 2, 3, 5
*1 The number of supported languages differs depending on the region where the
projector is used.
Wireless LAN menu
(EB-X21/EB-S21/EBX17/EB-S17 only)
s p.93
Security menu
(EB-X21/EB-S21/EBX17/EB-S17 only)
s p.95
Encryption Key 1, En‐ cryption Key 2, Encryp‐
tion Key 3, and Encryp‐
tion Key 4
Authentication Type
Open and Shared
Passphrase
-
List of Functions
Top Menu Name
85
Submenu Name
Setting Values
IP Settings
Wired LAN menu
(EB-X25/EB-W22/
EB-X22/EB-X20 only) IP Address Display
s p.96
DHCP, IP Address, Subnet Mask,
and Gateway Address
Mail menu
s p.97
Mail Notification
On and Off
SMTP Server
-
Port Number
-
s "Automatically Detect Input Signals and Change the Projected Image
(Source Search)" p.35
On and Off
Address 1 Setting, Ad‐ dress 2 Setting, and Ad‐
dress 3 Setting
Others menu
s p.98
SNMP
On and Off
Trap IP Address 1 and
Trap IP Address 2
-
AMX Device Discovery On and Off
Crestron RoomView
(EB-X25/EB-W22/EBX22/EB-X20 only)
On and Off
Bonjour
On and Off
Message Broadcasting
On and Off
Image Menu
Settable items vary depending on the image signal and source currently
being projected. Setting details are saved for each image signal.
Submenu
Function
Color Mode
You can select the quality of the image to suit your surroundings.
s "Selecting the Projection Quality (Selecting Color Mode)"
p.46
Brightness
You can adjust the image brightness.
Contrast
You can adjust the difference between light and dark in the
images.
Color Saturation
You can adjust the color saturation for the images.
Tint
(Adjustment is possible when a component video signal is being
input. If a composite video or S-video signal is input, adjustment
is only possible when NTSC signals are being input.)
You can adjust the image tint.
Sharpness
You can adjust the image sharpness.
Abs. Color Temp.
(This item cannot be selected if Color Mode is set to sRGBg.)
Adjusts the tint for the images. The image is tinted blue when you
raise the color temperature, and tinted red when you lower it.
List of Functions
Submenu
86
Function
Color Adjust‐
ment
(This item cannot be selected if Color Mode is set to sRGBg.)
You can adjust the color strength for Red, Green, and Blue
individually.
Auto Iris
(This item can be set only if Color Mode is set to Dynamic or
Theatre.)
Set to Normal or High Speed to adjust the iris to obtain the
optimum light for images being projected. Select High Speed to
make faster iris corrections to match the speed of the scene.
The setting is stored for each Color Mode.
s "Setting Auto Iris" p.47
Reset
You can reset all adjustment values for the Image menu to their
default settings. See the following to return all menu items to
their default settings.
s "Reset Menu" p.101
Signal Menu
Settable items vary depending on the image signal and source currently
being projected. Setting details are saved for each image signal.
s "Automatically Detect Input Signals and Change the Projected Image
(Source Search)" p.35
Submenu
Function
Auto Setup
Set to On to automatically adjust Tracking, Sync., and Position to
the optimum state when the input signal changes.
Resolution
Set to Auto to automatically identify the resolution of the input
signal. If images are not projected correctly when set to Auto, for
example if some of the image is missing, adjust to Wide for wide
screens, or set to Normal for 4:3 or 5:4 screens depending on the
connected computer.
Tracking
You can adjust computer images when vertical stripes appear in
the images.
Sync.
You can adjust computer images when flickering, fuzziness, or
interference appear in the images.
Position
You can adjust the display position up, down, left, and right when
a part of the image is missing so that the whole image is projected.
You cannot make settings on the Signal menu when the source is USB
Display, USB, or LAN.
List of Functions
Submenu
Progressive
87
Function
(When a component video or RGB video is being input, this
setting can only be adjusted if the signal being input is an
interlaced signal (480i/576i/1080i). This cannot be set when a
digital RGB signal is being input.)
Interlaceg (i) signal is converted to Progressiveg (p). (IP
conversion)
Off: Ideal for images with a large amount of movement.
Video: Ideal for general video images.
Film/Auto: This is ideal for movie films, computer graphics, and
animation.
Noise Reduction
(This cannot be set when a digital RGB signal is input or when
projecting an interlaced signal while Progressive is set to Off.)
Smoothes out rough images. There are two modes. Select your
favorite setting. It is recommended that this is set to Off when
viewing image sources in which noise is very low, such as for
DVDs.
HDMI Video
Range
When the projector's HDMI port is connected to a DVD player,
set the projector's video range according to the DVD player's
video range setting.
Input Signal
You can select input signal from Computer port.
If set to Auto, the input signal is set automatically according to
the connected equipment.
If colors do not appear correctly when set to Auto, select the
appropriate signal according to the connected equipment.
Video Signal
You can select the input signal from the Video port. If set to Auto,
video signals are recognized automatically. If interference
appears in the image or a problem occurs such as no image is
being projected when set to Auto, select the appropriate signal
according to the connected equipment.
Aspect
You can set the aspect ratiog for projected images.
s "Changing the Aspect Ratio of the Projected Image" p.47
Submenu
Function
Overscan
Changes the output image ratio (the range of the projected
image). You can set the cropping range to Off, 4%, or 8%. When
the source is HDMI, Auto is available. When Auto is selected, it
automatically changes to Off or 8% according to the input signal.
Image Process‐
ing
Changes settings for image processing.
Fast: Images are displayed quicker. The pen's tracking delay is
improved when using the optional interactive unit.
Fine: Images are displayed in higher quality.
Reset
You can reset all adjustment values on the Signal menu to their
default settings, except for Input Signal and Image Processing.
See the following to return all menu items to their default
settings.
s "Reset Menu" p.101
List of Functions
88
Submenu
Settings Menu
Pointer Shape
Function
You can select the shape of the pointer.
Pointer 1:
Pointer 2:
Pointer 3:
s "Pointer Function (Pointer)" p.58
Submenu
Function
Keystone
You can correct keystone distortion.
• When H/V-Keystone is selected:
Adjust V-Keystone and H-Keystone to correct horizontal
and vertical keystone distortion.
You can also set H-Keystone Adjuster and Auto VKeystone to On or Off.
• When Quick Corner is selected:
Select and correct the four corners of the projected image.
s "Quick Corner" p.42
Zoom
(EB-S21/EB-S17
only)
Adjusts the size of the projected image.
Control Panel
Lock
You can use this to restrict operation of the projector's control
panel.
s "Restricting Operation (Control Panel Lock)" p.67
Volume
You can adjust the volume. Setting values are saved for each
source.
Remote Receiver
You can limit the reception of the operation signal from the
remote control.
When set to Off, you cannot perform any operations from the
remote control. If you want to make operations from the remote
control, hold down the [Menu] button on the remote control for
at least 15 seconds to reset the setting to its default value.
User Button
You can select and assign an item from the Configuration menu
with the remote control's [User] button. Pressing the [User]
button directly displays the assigned menu item selection/
adjustment screen, allowing you to make one-touch changes to
settings/adjustments. You can assign one of the following items
to the [User] button.
Power Consumption, Info, Progressive, Resolution, and
Pattern Display
List of Functions
89
Submenu
Pattern
Function
Pattern Display: Display a pattern.
Pattern Type: You can select from Patterns 1 to 4 or User
Pattern. Patterns 1 to 4 display projection lines such as ruled lines
or a grid.
Pattern 1:
Pattern 2:
Pattern 3:
Pattern 4:
User Pattern: Captures a user pattern.
s "Saving User Pattern" p.63
Test Pattern: When the projector is set up, a test pattern is
displayed so that you can adjust the projection status without
connecting equipment. While the test pattern is displayed, zoom,
focus adjustments, and keystone correction can be performed.
To cancel the test pattern, press the [Esc] button on the remote
control or the control panel.
Extended Menu
Submenu
Display
You can make settings related to the projector's display.
Messages: When set to Off, the following items will not be
displayed.
Item names when the Source, Color Mode, or Aspect Ratio
is changed, messages when no signal is being input, and
warnings such as High Temp Warning.
Display Background*1: You can set the screen background
to Black, Blue, or Logo when no image signal is available.
Startup Screen*1: Set to On to display the User's Logo
when projection starts.
A/V Mute*1: You can set the screen displayed when the
remote control's [A/V Mute] button is pressed to Black,
Blue, or Logo.
User's Logo*1
You can change the user's logo that is displayed as a
background during Display Background, A/V Mute, and so
on.
s "Saving a User's Logo" p.61
Attention
If a pattern is displayed for a long time, a residual
image may be visible in projected images.
Reset
You can reset all adjustment values on the Settings menu to their
default settings, except for Zoom (EB-S21/EB-S17 only) and
User Button.
See the following to return all menu items to their default
settings.
s "Reset Menu" p.101
Function
List of Functions
Submenu
Projection
Operation
90
Function
Select from one of the following projection methods
depending on how the projector is installed.
Front, Front/Ceiling, Rear, and Rear/Ceiling
You can change the setting as follows by pressing down
the [A/V Mute] button on the remote control for about five
seconds.
FrontWFront/Ceiling
RearWRear/Ceiling
s "Installation Methods" p.22
Submenu
A/V Settings
Function
A/V Output: (This item can be set only if Standby Mode is
set to Communication On.)
Set to Always On to output audio and images to external
equipment when the projector is in standby status. Audio is
output from the speaker.
a
Direct Power On: Set to On to turn on the projector
simply by plugging it in.
When the power cord is plugged in, note that the projector
turns on automatically in cases such as a power outage
being restored.
High Altitude Mode: Set to On when using the projector
above an altitude of 1500 m.
Startup Source Search: Set to On to project images from
the port currently receiving an image when the projector
starts.
The fan may rotate in standby status. Also,
when the projector wakes from standby
status, the fan may make a loud noise as it
rotates, but this is not a malfunction.
Audio Output: Select the audio output when projecting
images from the Computer1, Computer2, S-Video, or Video
input ports. When set to Auto, the audio from the audio
input port that matches each image input port is output. In
standby status, the audio from the last selected source is
output.
s "Connecting Equipment" p.25
HDMI Audio Output: Select the audio source when
projecting images from the HDMI input port. Select HDMI
to output the image's audio as it is.
Language
You can set the language for messages and menus.
Reset
You can reset the adjustment values for Display*1,
Operation*2, and A/V Settings*3 from the Extended menu
to their default settings.
See the following to return all menu items to their default
settings.
s "Reset Menu" p.101
*1 When User's Logo Protect is set to On in Password Protect, settings related
to user's logo cannot be changed. You can make changes after setting User's
Logo Protect to Off.
s "Managing Users (Password Protect)" p.65
*2 Except for High Altitude Mode and Startup Source Search.
*3 Except for A/V Output.
List of Functions
91
Network Menu
When Network Protect is set to On in Password Protect, a message is
displayed and the network settings cannot be changed. Set Network Protect
to Off and then configure the network.
s "Setting Password Protect" p.65
Submenu
Function
Net. Info. Wired LAN
(EB-X25/EB-W22/
EB-X22/EB-X20
only)
Displays the following network setting status information.
• Projector Name
• DHCP
• IP Address
• Subnet Mask
• Gateway Address
• MAC Address
Network Config‐
uration
The following menus are available for setting Network
items.
Basic, Wireless LAN, Security, Wired LAN, Mail, Others,
Reset, and Complete
*
Displays available region information for the Wireless LAN unit being used.
For more details, contact your local dealer or the nearest address provided in
the Epson Projector Contact List.
s Epson Projector Contact List
a
Submenu
Function
Net. Info. - Wire‐
less LAN
(EB-X21/EB-S21/
EB-X17/EB-S17
only)
Displays the following network setting status information.
• Connection Mode
• Antenna Level
• Projector Name
• SSID
• DHCP
• IP Address
• Subnet Mask
• Gateway Address
• MAC Address
• Region Code*
• By using a Web browser of a computer connected to the projector
on a network, you can set functions and control the projector. This
function is called Web Control. You can easily enter text using a
keyboard to make settings for Web Control such as Security settings.
s "Changing Settings Using a Web Browser (Web Control)"
p.70
• Contact your network administrator for details on network settings.
Notes on operating the Network menu
Selecting from the top menu and sub menus, and changing selected items is
the same as making operations from the Configuration menu.
When done, make sure you go to the Complete menu, and select Yes, No,
or Cancel. When you select Yes or No, you are returned to the
Configuration menu.
List of Functions
92
Yes: Saves the settings and exits the Network menu.
No: Does not save the settings and exits the Network menu.
Cancel: Continues displaying the Network menu.
Soft keyboard operations
The Network menu contains items that require input of alphanumerics
during setup. In this case, the following software keyboard is displayed.
Press the [
][
][ ][ ] buttons on the remote control or the [w][v]
[a][b] buttons (or the [Wide][Tele]) on the control panel. Use the buttons
to move the cursor to the desired key, and then press the [ ] button.
Enter figures by holding down the [Num] button on the remote control,
and pressing the numeric buttons. After inputting, press Finish on the
keyboard to confirm your input. Press Cancel on the keyboard to cancel
your input.
• Each time the CAPS key is selected and the [
sets and changes between upper case and lower
• Each time the SYM1/2 key is selected and the [
sets and changes the symbol keys for the section
] button is pressed, it
case letters.
] button is pressed, it
enclosed by the frame.
List of Functions
93
Basic menu
Submenu
Projector Key‐
word
Function
When set to On, you have to enter the keyword when you try to
connect the projector to a computer via a network. As a result,
you can prevent presentations from being interrupted by
connections from other computers.
Normally this should be set to On.
s EasyMP Network Projection Operation Guide
s EasyMP Multi PC Projection Operation Guide
Wireless LAN menu (EB-X21/EB-S21/EB-X17/EB-S17 only)
Submenu
Function
Projector Name
Displays the projector name used to identify the projector when
connected to a network.
When editing, you can enter up to 16 single-byte alphanumeric
characters.
PJLink Password
(EB-X25/EB-W22/
EB-X22/EB-X20
only)
Set a password to use when you access the projector using
compatible PJLink software. You can enter up to 32 single-byte
alphanumeric characters.
Web Control
Password
Set a password to use when making settings and controlling the
projector using Web Control. Enter no more than eight singlebyte alphanumeric characters. Web Control is a computer
function that allows you to set up and control the projector by
using the Web browser on a computer connected on a network.
s "Changing Settings Using a Web Browser (Web Control)"
p.70
Submenu
Wireless LAN
Power
Function
Turn On when connecting the projector to the computer over
wireless LAN.
If you do not want to connect via wireless LAN, turn it Off to
prevent unauthorized access by others.
The default value is On.
List of Functions
Submenu
94
Function
Connection
Mode
Set the connection mode to use when connecting the projector
and a computer via a wireless LAN.
If you select Quick, a small network is created automatically by
the projector and computer. It is used with EasyMP Network
Projection. If SSID Auto Setting is set to On, the projector
becomes an easy access point; if it is set to Off, the network is
created in Ad hoc modeg.
If you select Advanced, the connection is established in
Infrastructure modeg.
Channel
(This can only be set if Connection Mode is set to Quick.)
Select the frequency band used by the wireless LAN from 1ch,
6ch, or 11ch.
The default value is 11ch.
Wireless LAN
Sys.
Set the Wireless LAN system to either 802.11b/g or
802.11b/g/n.
The default value is 802.11b/g/n.
SSID Auto Set‐
ting
(This can only be set if Connection Mode is set to Quick.)
When you set this to On, you can search for the projector more
quickly from among multiple projectors. SSID is set
automatically.
When connecting to multiple projectors from one computer in
Quick mode, set this to Off, and set the same SSID in all the
projectors that will connect.
SSID
(This item can only be set when SSID Auto Setting is set to
Off.)
Enter an SSIDg. When an SSID is provided for the wireless LAN
system in which the projector participates, enter the SSID.
You can enter up to 32 single-byte alphanumeric characters.
Submenu
Function
IP Settings
(This item can only be set if Connection Mode is set to
Advanced.)
You can make network settings.
DHCP: Set to On to make network settings using DHCPg. If this
is set to On, you cannot set any more addresses.
IP Address: You can input the IP addressg assigned to the
projector. You can enter a number from 0 to 255 in each field of
the address. However, the following IP addresses cannot be used.
0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a
number from 0 to 255)
Subnet Mask: You can input the subnet maskg for the projector.
You can enter a number from 0 to 255 in each field of the address.
However, the following subnet masks cannot be used.
0.0.0.0, 255.255.255.255
Gateway Address: You can input the IP address for the gateway
for the projector. You can enter a number from 0 to 255 in each
field of the address. However, the following Gateway addressesg
cannot be used.
0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a
number from 0 to 255)
SSID Display
To prevent the SSIDg from being displayed on the LAN Standby
screen, set this to Off.
IP Address Dis‐
play
To prevent the IP addressg from being displayed on the LAN
Standby screen, set this to Off.
List of Functions
95
Security menu (EB-X21/EB-S21/EB-X17/EB-S17 only)
Available when the Wireless LAN unit is installed.
Submenu
Submenu
Function
Encryption Key
1/Encryption Key
2/Encryption Key
3/Encryption Key
4
You can enter the key used for WEP encryption. Enter the key in
single-byte characters following instructions from the network
administrator for the network in which the projector
participates. The type of character and the number that can be
entered differ according to the WEP Encryption and Format
settings.
128Bit - ASCII: Single-byte alphanumeric, 13 characters.
64Bit - ASCII: Single-byte alphanumeric, 5 characters.
128Bit - HEX: 0 to 9 and A to F, 26 characters
64Bit - HEX: 0 to 9 and A to F, 10 characters
Authentication
Type
Set the WEP authentication type.
Open: Uses open system authentication.
Shared: Uses shared key authentication.
Passphrase
Enter the passphrase. You can enter at least 8 and up to 63 singlebyte alphanumeric characters.
When using it with EasyMP Network Projection, you do not
need to input the passphrase in the computer if it is the initial
(default) passphrase.
In the interests of security, we recommended that you change the
passphrase periodically. If the network settings are initialized, it
returns to the initial passphrase.
s "Reset menu" p.99
You can enter up to 32 characters on the Configuration menu.
When entering more than 32 characters, use your Web browser
to enter the text.
s "Changing Settings Using a Web Browser (Web Control)"
p.70
In Quick mode, the initial passphrase is set.
Function
Security
Select the security type from the items that are displayed.
When setting up Security, follow the instructions from the
administrator of the network system you are about to access.
WEP Encryption
You can set the encryption for WEP encryption.
128Bit: Uses 128 (104) bit encoding.
64Bit: Uses 64 (40) bit encoding.
Format
You can set the input method for the WEP encryption key.
ASCII: Input text.
HEX: Input in HEX (hexadecimal).
Key ID
Selects the WEP encryption ID key.
Type of security
When the Wireless LAN unit is installed and you are using Advanced, it is
strongly recommended that you set security. Select one of the following
security methods.
List of Functions
• WEP
Data is encrypted with a code key (WEP key). This mechanism prevents
communication unless the encrypted keys for the access point and the
projector match.
96
Wired LAN menu (EB-X25/EB-W22/EB-X22/EB-X20 only)
• WPA
This is an encryption standard that improves security which is a weak
point of WEP. Although there are multiple kinds of WPA encryption
methods, this projector uses TKIP and AES.
WPA also includes user authentication functions. WPA authentication
provides two methods: using an authentication server, or authenticating
between a computer and an access point without using a server. This
projector supports the latter method, without a server.
a
For setting details, follow the directions from the network
administrator of your network.
Submenu
IP Settings
Function
You can make settings related to the following addresses.
DHCPg: Set to On to configure the network using DHCP. If this
is set to On, you cannot set any more addresses.
IP Addressg: You can input the IP address assigned to the
projector. You can input a number from 0 to 255 in each field of
the address. However, the following IP addresses cannot be used.
0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a
number from 0 to 255)
Subnet Maskg: You can input the subnet mask for the projector.
You can input a number from 0 to 255 in each field of the address.
However, the following subnet masks cannot be used.
0.0.0.0, 255.255.255.255
Gateway Addressg: You can input the IP address for the gateway
for the projector. You can input a number from 0 to 255 in each
field of the address. However, the following gateway addresses
cannot be used.
0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a
number from 0 to 255)
List of Functions
Submenu
IP Address Dis‐
play
97
Function
To prevent the IP address from being displayed on Network Info
in the Network Menu and on the LAN Standby screen, set this to
Off.
Mail menu
When this is set, you receive an email notification if a problem or warning
occurs in the projector.
s "Using the Mail Notification Function to Report Problems" p.72
Submenu
Function
Mail Notification
Set to On to send an email to the preset addresses when a problem
or warning occurs with a projector.
SMTP Server
You can input the IP addressg for the SMTP server for the
projector.
You can enter a number from 0 to 255 in each field of the address.
However, the following IP addresses cannot be used.
127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from
0 to 255)
Submenu
Function
Port Number
You can input the port number for the SMTP server. The default
value is 25. You can input numbers between 1 to 65535.
Address 1 Set‐
ting/Address 2
Setting/Address
3 Setting
You can input the email address of the destination to send the
notification email to. You can register up to three destinations.
You can enter up to 32 single-byte alphanumeric characters for
the email addresses.
You can select the problems or warnings to be notified about by
email. When the selected problem or warning occurs in the
projector, an email is sent to the specified destination address
notifying that a problem or warning has occurred. You can select
multiple items from the displayed items.
List of Functions
98
Others menu
Submenu
Function
SNMP
Set to On to monitor the projector using SNMP.
To monitor the projector, you need to install the SNMP manager
program on your computer. SNMP should be managed by a
network administrator.
The default value is Off.
Trap IP Address
1/Trap IP Ad‐
dress 2
You can register up to two IP addresses for the SNMP trap
notification destination. You can enter a number from 0 to 255 in
each field of the address. However, the following IP addresses
cannot be used. 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x
is a number from 0 to 255)
AMX Device Dis‐
covery
When the projector is connected to a network, set this to On to
allow the projector to be detected by AMX Device Discoveryg.
Set this to Off if you are not connected to an environment
controlled with a controller from AMX or AMX Device
Discovery.
Submenu
Function
Crestron Room‐
View
(EB-X25/EB-W22/
EB-X22/EB-X20
only)
Set this to On only when monitoring or controlling the projector
over the network using Crestron RoomView . Otherwise, set
this to Off.
s "About Crestron RoomView (EB-X25/EB-W22/EB-X22/
EB-X20 only)" p.75
When this is set to On, the following functions are not available.
• Web control
• Message Broadcasting (EasyMP Monitor plugin)
Bonjour
Set this to On when connecting to the network using Bonjour.
See Apple's Web site for more information on the Bonjour
service.
s http://www.apple.com/
Message Broad‐
casting
You can switch the EPSON Message Broadcasting function to
enable or disable.
®
®
List of Functions
99
Reset menu
ECO Menu
Resets all of the network settings.
Submenu
Reset network
settings.
When you make ECO menu settings, the projector performs functions to
save power. When power saving settings have been enabled, a leaf icon is
displayed next to each submenu.
Function
To reset all of the Network settings, select Yes.
Submenu
Function
Power Consump‐
tion
You can set the lamp brightness to one of two settings. Select
ECO if the images being projected are too bright, such as when
projecting images in a dark room or onto a small screen. When
ECO is selected, power consumption during projection
decreases, and fan rotation noise is reduced.
When using at high altitude or in locations subject to high
temperatures, you may not be able to change settings.
Light Optimizer
(This item can only be set when Power Consumption is set to
Normal.)
When set to On, the lamp brightness is adjusted according to the
image being projected. This helps to reduce the amount of
electricity being used by lowering the lamp's brightness
according to the scene being projected.
The setting is stored for each Color Mode.
List of Functions
Submenu
100
Function
Info Menu (Display Only)
Sleep Mode
When set to On, this automatically stops projection when no
image signal is being input and no operations are carried out for a
specified length of time. Also, if no image signal is input for
approximately five minutes, the lamp dims until the power turns
off. When an image signal is input, the projector returns to
normal operating status.
Sleep Mode Tim‐
er
When Sleep Mode is set to On, you can set the time before the
projector automatically turns off within a range of 1 to 30
minutes.
Lens Cover Timer
When set to On, this turns off the power automatically 30
minutes after the lens cover is closed. Also, if the lens cover is
closed for approximately five minutes, the lamp dims until the
power turns off. When the lens cover is opened, the projector
returns to normal operating status.
A/V Mute Timer
When set to On, this turns off the power automatically 30
minutes after A/V mute is enabled. Also, if A/V mute is enabled,
the lamp dims until the power turns off. When A/V mute is
disabled, the projector returns to normal operating status.
Standby Mode
If you set Communication On, you can perform the following
operations even if the projector is in standby mode.
• Monitoring and controlling the projector over a network.
• Outputting audio and images to external equipment. (Only
when A/V Output is set to Always On.)
ECO Display
When set to On, when the lamp brightness changes from normal
to low or low to normal, leaf icons are displayed at the bottomleft of the projected screen to indicate the power-saving status.
Lamp Hours
You can reset all adjustment values for the ECO menu to their
default settings. See the following to return all menu items to
their default settings.
s "Reset Menu" p.101
You can display the cumulative lamp operating time*.
When the lamp replacement time is reached, the characters
are displayed in yellow.
Source
You can display the source name for the connected
equipment currently being projected.
Input Signal
You can display the content of Input Signal set in the
Signal menu according to the source.
Resolution
You can display the resolution.
Refresh Rate
You can display the refresh rateg.
Reset
Lets you check the status of the image signals being projected and the status
of the projector. Items that can be displayed vary depending on the source
currently being projected. Depending on the model used, some input
sources are not supported.
s "Automatically Detect Input Signals and Change the Projected Image
(Source Search)" p.35
Submenu
Function
List of Functions
Submenu
101
Function
Sync Info
You can display the image signal information.
This information may be needed if service is required.
Video Signal
You can display the settings for Video Signal in the Signal
menu.
Status
This is information about errors that have occurred on the
projector.
This information may be needed if service is required.
Serial Number
Displays the projector's serial number.
Version
Displays the projector's firmware version.
Event ID
Displays the application error log.
s "About Event ID" p.80
*
Reset Menu
The cumulative use time is displayed as "0H" for the first 10 hours. 10 hours
and above is displayed as "10H", "11H", and so on.
Submenu
Function
Reset All
You can reset all items in the Configuration menu to their default
settings.
The following items are not reset to their defaults: Input Signal,
User's Logo, Lamp Hours, Language, Password, Zoom (EBS21/EB-S17 only), and all items on the Network menu.
Reset Lamp
Hours
Clears the cumulative lamp hours use time. Reset when you
replace the lamp.
Troubleshooting
This chapter explains how to identify problems and what to do if a problem is found.
Using the Help
103
If a problem occurs with the projector, the Help screen is displayed to assist
you by pressing the Help button. You can solve problems by answering the
questions.
a
c
Confirm the selection.
Using the remote control
Using the control panel
Press the [Help] button.
The Help screen is displayed.
Using the remote control
Using the control panel
Questions and solutions are displayed as shown on the screen below.
Press the [Help] button to exit the Help.
b
Select a menu item.
a
See the following if the Help function does not provide a
solution to the problem.
s "Problem Solving" p.104
Using the remote control
Using the control panel
Problem Solving
104
If you are having a problem with the projector, first check the projector's indicators and refer to "Reading the Indicators" below.
See the following if the indicators do not show clearly what the problem might be.
s "When the Indicators Provide No Help" p.108
Reading the Indicators
The projector is provided with the following four indicators that indicate the operating status of the projector.
A
B
C
D
Power indicator
Indicates the projector's status.
Status indicator
Indicates the projector's status.
Lamp indicator
Indicates the projection lamp status.
Temp indicator
Indicates the internal temperature status.
Indicators
Power supply
Blue - Lit
Blue - Lit
Status
Explanation
Status
Off
Standby condition
Power is being supplied to the projector. When the [t] power button is pressed in this condition, projection
starts.
Network monitoring
status
The projector is being monitored and controlled over a network (when Standby Mode is set to
Communication On). If the power cord is disconnected and connected in this status, the power indicator
flashes blue.
Blue - Flashing Warm-up status
This is the status immediately after turning on the projector. Warm-up takes approximately 30 seconds after
the lamp turns on. In this status you cannot turn off the projector, even if you press the [t] power button.
Problem Solving
105
Indicators
Power supply
Status
Explanation
Status
Blue - Lit
Blue - Lit
Cool down status
This is the status immediately after turning off the projector. In this status, all buttons are disabled.
Normal status
The projector is projecting.
Refer to the following table to see what the indicators mean and how to remedy problems that they indicate.
If all indicators are off, check that the power cord is connected correctly and that the power is being supplied normally.
Sometimes, when the power cord is unplugged, the [t] power indicator remains lit for a short period, but this is not a fault.
Indicators
Power sup‐
ply
Off
Off
Off
Status
Blue - Flash‐
ing
Blue - Flash‐
ing
Blue - Flash‐
ing
Cause
Lamp
Orange Flashing
Off
Off
Remedy or Status
Tempera‐
ture
Internal Error
Stop using the projector, remove the power plug from the electrical outlet, and contact your local
dealer or the nearest address provided in the Epson Projector Contact List.
s Epson Projector Contact List
Fan Error
Sensor Error
Stop using the projector, remove the power plug from the electrical outlet, and contact your local
dealer or the nearest address provided in the Epson Projector Contact List.
s Epson Projector Contact List
High Temp Error
(Overheating)
The lamp turns off automatically and projection stops. Wait for about five minutes. After about five
minutes the projector switches to standby mode, so check the following two points.
• Check that the air filter and air exhaust vent are clear, and that the projector is not positioned
against a wall.
Off
Orange Flashing
Orange - Lit
• If the air filter is clogged, clean or replace it.
s "Cleaning the Air Filter" p.119, "Replacing the Air Filter" p.124
If the error continues after checking the points above, stop using the projector, remove the power
plug from the electrical outlet, and contact your local dealer or the nearest address provided in the
Epson Projector Contact List.
s Epson Projector Contact List
When using at an altitude of 1500 m or more, set High Altitude Mode to On.
s "Extended Menu" p.89
Problem Solving
106
Indicators
Power sup‐
ply
Off
Status
Blue - Flash‐
ing
Lamp
Orange - Lit
Cause
Remedy or Status
Tempera‐
ture
Off
Lamp Error
Lamp Failure
Check the following two points.
• Take out the lamp and check if it is cracked.
s "Replacing the Lamp" p.121
• Clean the air filter.
s "Cleaning the Air Filter" p.119
If the lamp is not cracked: Reinstall the lamp and plug in the power cord.
If the error continues: Stop using the projector, remove the power plug from the electrical outlet, and
contact your local dealer or the nearest address provided in the Epson Projector Contact List.
s Epson Projector Contact List
If the lamp is cracked: Contact your local dealer or the nearest address provided in the Epson
Projector Contact List. (Images cannot be projected until the lamp is replaced.)
s Epson Projector Contact List
When using at an altitude of 1500 m or more, set High Altitude Mode to On.
s "Extended Menu" p.89
Off
Blue - Flash‐
ing
Orange Flashing
Lamp Cover Open
Check that the lamp and the lamp cover are securely installed.
The lamp does not turn on if the lamp and the lamp cover are not installed correctly.
s "Replacing the Lamp" p.121
Auto Iris Error
Stop using the projector, remove the power plug from the electrical outlet, and contact your local
dealer or the nearest address provided in the Epson Projector Contact List.
s Epson Projector Contact List
Orange Flashing
Power Err.
Off
Blue - Flash‐
ing
Blue - Flash‐
ing
State de‐
pendant in‐
dication
Orange - Lit
State de‐
pendant in‐
dication
Orange - Lit
Orange Flashing
High Temp Warn‐
ing
(This is not an abnormality. However, if the temperature rises too high again, projection stops
automatically.)
• Check that the air filter and air exhaust vent are clear, and that the projector is not positioned
against a wall.
• If the air filter is clogged, clean or replace it.
s "Cleaning the Air Filter" p.119, "Replacing the Air Filter" p.124
Problem Solving
107
Indicators
Power sup‐
ply
Status
Lamp
Cause
Tempera‐
ture
Replace Lamp
Blue - Flash‐
ing
a
State de‐
pendant in‐
dication
Orange Flashing
Remedy or Status
State de‐
pendant in‐
dication
Replace it with a new lamp.
s "Replacing the Lamp" p.121
If you continue to use the lamp after the replacement period has passed, the possibility that the lamp
may explode increases. Replace it with a new lamp as soon as possible.
• See the following if the projector is not operating properly, even though the indicators are all showing normal.
s "When the Indicators Provide No Help" p.108
• If the indicators are in a state not shown in this table, stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or
the nearest address provided in the Epson Projector Contact List.
s Epson Projector Contact List
Problem Solving
108
When the Indicators Provide No Help
If any of the following problems occur and the indicators do not offer a
solution, refer to the pages given for each problem.
Problems Relating to Images
s p.109
• No images appear
Projection does not start, the projection area is completely black,
or the projection area is completely blue.
• Moving images are not displayed
Moving images being projected from a computer appear black
and nothing is projected.
s p.110
• Projection stops automatically
s p.110
• The message "Not supported" is displayed
s p.110
• The message "No Signal" is displayed
s p.111
• Images are fuzzy, out of focus, or distorted
s p.111
• Interference or distortion appear in images
s p.112
s p.113
• The image is truncated (large) or small, the aspect ratio is not
suitable, or the image has been reversed
Only part of the image is displayed, the height and width ratios
of the image are not correct, or the image may appear reversed
from top to bottom or left to right.
s p.113
• Image colors are not right
The whole image appears purplish or greenish, images are black
& white, or colors appear dull.
• Images appear dark
s p.114
Problems when projection starts
• The projector does not turn on
s p.115
Other Problems
• No sound can be heard or the sound is faint
s p.115
• There is noise in the audio
s p.116
• The remote control does not work
s p.116
• I want to change the language for messages and menus
s p.117
• Mail is not received even if a problem occurs in the projector
s p.117
• Cannot change settings using a Web browser
s p.117
Problem Solving
109
Problems Relating to Images
No images appear
Check
Remedy
Did you press the [t] power button?
Press the [t] power button to turn the power on.
Are the indicators switched off?
The power cord is not connected correctly or power is not being supplied.
Connect the projector's power cord correctly.
s "From Installation to Projection" p.34
Check that your electrical outlet or power source is functioning correctly.
Is A/V Mute active?
Press the [A/V Mute] button on the remote control to cancel A/V Mute.
s "Hiding the Image and Sound Temporarily (A/V Mute)" p.57
Is the A/V mute slide closed?
Open the A/V mute slide.
s "Front/Top" p.11
Are the Configuration menu settings correct?
Reset all of the settings.
s Reset - Reset All p.101
Is the image to be projected completely black?
(Only when projecting computer images)
Some input images, such as screen savers, may be completely black.
Is the image signal format setting correct?
(Only when projecting images from a video source)
Change the setting according to the signal for the connected equipment.
s Signal - Video Signal p.86
Is the USB cable connected correctly?
(Only when projecting USB Display)
Check that the USB cable is connected correctly. Reconnect it if it is not connected or not connected properly.
Is Windows Media Center displayed in full screen?
When Windows Media Center is displayed at full screen, you cannot project using USB Display or network connection.
(Only when projecting using USB Display or network connection) Reduce the screen size.
Is an application using the Windows DirectX function displayed? Applications using the Windows DirectX function may not display images correctly.
(Only when projecting using USB Display or network connection)
Problem Solving
110
Moving images are not displayed
Check
Remedy
Is the computer's image signal being output to the LCD and the
monitor?
(Only when projecting images from a laptop computer or a
computer with a built-in LCD screen)
Change the image signal from the computer to external output only. Check your computer's documentation, or contact
the computer's manufacturer.
Are the contents of the moving image you are trying to project
copyright protected?
The projector may not be able to project copyright protected moving images that are being played back on a computer.
For more details, see the user's guide supplied with the player and so on.
Projection stops automatically
Check
Remedy
Are Sleep Mode, Lens Cover Timer, or A/V Mute Timer set to
On?
If any of these are set to On, the power turns off automatically in the following situations.
• When Sleep Mode is set to On: If no operations are performed for a specified length of time while no image signal is
being input.
• When Lens Cover Timer is set to On: If approximately 30 minutes has passed since the lens cover was closed.
• When A/V Mute Timer is set to On: If approximately 30 minutes has passed since the A/V mute was enabled.
To prevent the projector from switching off automatically, make sure each setting is set to Off.
s "ECO Menu" p.99
Is the computer in power-saving mode?
If the computer is in power-saving mode and no operations are performed for a specified period of time, the image may
disappear. Perform an operation on the computer to display the image again.
The message "Not supported" is displayed
Check
Is the image signal format setting correct?
(Only when projecting images from a video source)
Remedy
Change the setting according to the signal for the connected equipment.
s Signal - Video Signal p.86
Do the image signal resolution and the refresh rate correspond to the Refer to the computer's documentation for how to change the image signal resolution and the refresh rate output from
mode?
the computer.
(Only when projecting computer images)
s "Supported Monitor Displays" p.133
Problem Solving
111
The message "No Signal" is displayed
Check
Remedy
Are the cables connected correctly?
Check that all the cables required for projection are securely connected.
s "From Installation to Projection" p.34
Is the correct port selected?
Change the image by pressing the [Source Search] button on the remote control or the control panel.
s "Automatically Detect Input Signals and Change the Projected Image (Source Search)" p.35
Is the power for the computer or video source turned on?
Turn the power on for the equipment.
Are the image signals being output to the projector?
(Only when projecting images from a laptop computer or a
computer with a built-in LCD screen)
If the image signals are only being output to the computer's LCD monitor or to the accessory monitor, you need to
change the output to an external destination as well as the computer's own monitor. For some computer models, when
the image signals are output externally, they no longer appear on the LCD monitor or accessory monitor.
If the connection is made while the power of the projector or computer is already turned on, the Fn key (Function key)
that changes the computer's image signal to external output may not work. Turn the power for the computer and the
projector off and then back on again.
s "From Installation to Projection" p.34
s Computer's documentation
Is the computer in power-saving mode?
If the computer is in power-saving mode and no operations are performed for a specified period of time, the image may
disappear. Perform an operation on the computer to display the image again.
Images are fuzzy, out of focus, or distorted
Check
Remedy
Is Auto V-Keystone set to Off?
Setting it to On enables Auto V-Keystone.
s Settings - Keystone - H/V-Keystone - Auto V-Keystone p.88
If you are using the projector with this setting off, manually adjust the projected image.
s "Correcting manually" p.41
Is the focus adjusted correctly?
Turn the focus ring to adjust the focus.
s "Correcting the Focus" p.45
Is the projector at the correct distance?
Is it projecting outside of the recommended projection distance range?
Setup within the recommended range.
s "Screen Size and Projection Distance" p.128
Problem Solving
112
Check
Remedy
Is the keystone adjustment value too large?
Lower the projection angle to reduce the amount of keystone correction.
s "Adjusting the Image Position" p.45
Has condensation formed on the lens?
If the projector is suddenly taken from a cold environment to a warm environment, or if sudden ambient temperature
changes occur, condensation may form on the surface of the lens, and this may cause the images to appear fuzzy. Set the
projector up in the room about one hour before it is used. If condensation forms on the lens, turn the projector off and
wait for the condensation to disappear.
Interference or distortion appear in images
Check
Remedy
Is the image signal format setting correct?
(Only when projecting images from a video source)
Change the setting according to the signal for the connected equipment.
s Signal - Video Signal p.86
Are the cables connected correctly?
Check that all the cables required for projection are securely connected.
s "Connecting Equipment" p.25
Is an extension cable being used?
If an extension cable is used, electrical interference may affect the signals. Use the cables supplied with the projector to
check if the cables you are using may be causing the problem.
Is the correct resolution selected?
(Only when projecting computer images)
Set the computer so that the signals being output are compatible with the projector.
s "Supported Monitor Displays" p.133
s Computer's documentation
Are the Sync.g and Trackingg settings adjusted correctly?
(Only when projecting computer images)
Press the [Auto] button on the remote control or the [ ] button on the control panel to perform automatic adjustment.
If the images are not adjusted correctly even after performing automatic adjustment, you can also make adjustments
from the Configuration menu.
s Signal - Tracking, Sync. p.86
Is Transfer layered window selected?
(Only when projecting USB Display)
Click All Programs - EPSON Projector - Epson USB Display - Epson USB Display Vx.xx Settings, and then clear the
Transfer layered window check box.
The mouse cursor flickers (only when projecting USB Display)
Is Make the movement of the mouse pointer smooth. selected?
Click All Programs - EPSON Projector - Epson USB Display - Epson USB Display Vx.xx Settings, and then select
Make the movement of the mouse pointer smooth.(This is not available for Windows 2000.)
For Windows Vista/7, Windows Aero is disabled when this is selected.
Problem Solving
113
The image is truncated (large) or small, the aspect is not suitable, or the image has been reversed
Check
Remedy
Is a wide panel computer image being projected?
(Only when projecting computer images)
Change the setting according to the signal for the connected equipment.
s Signal - Resolution p.86
Is the image still being enlarged by E-Zoom?
Press the [Esc] button on the remote control to cancel E-Zoom.
s "Enlarging Part of the Image (E-Zoom)" p.59
Is the image position adjusted correctly?
Press the [Auto] button on the remote control or the [Enter] button on the control panel to perform automatic
adjustment of the computer image being projected. If the images are not adjusted correctly even after performing
automatic adjustment, you can also make adjustments from the Configuration menu.
Apart from computer image signals, you can adjust other signals while projecting from the Configuration menu.
s Signal - Position p.86
Is the computer set for dual display?
(Only when projecting computer images)
If dual display is activated in the Display Properties of the computer's Control Panel, only about half of the image on the
computer screen is projected. To display the entire image on the computer screen, turn off the dual display setting.
s Computer video driver documentation
Is the correct resolution selected?
(Only when projecting computer images)
Set the computer so that the signals being output are compatible with the projector.
s "Supported Monitor Displays" p.133
s Computer's documentation
Is the projection mode correct?
Depending on how the projector is installed, set the projection mode from one of the following: Front, Front/Ceiling,
Rear, Rear/Ceiling.
s Extended - Projection p.89
s "Installation Methods" p.22
Image colors are not right
Check
Do the input signal settings match the signals from the connected
device?
Remedy
Change the following settings according to the signal for the connected equipment.
• When the image is from a device connected to the Computer port.
s Signal - Input Signal p.86
• When the image is from a device connected to the Video or S-Video port.
s Signal - Video Signal p.86
Problem Solving
114
Check
Remedy
Is the image brightness adjusted correctly?
Adjust the Brightness setting from the Configuration menu.
s Image - Brightness p.85
Are the cables connected correctly?
Check that all the cables required for projection are securely connected.
Check that no cables are disconnected and that there are no poor contacts in the cables.
s "Connecting Equipment" p.25
Is the contrastg adjusted correctly?
Adjust the Contrast setting from the Configuration menu.
s Image - Contrast p.85
Is the color adjustment set correctly?
Adjust the Color Adjustment setting from the Configuration menu.
s Image - Color Adjustment p.85
Are the color saturation and tint adjusted correctly?
(Only when projecting images from a video source)
Adjust the Color Saturation and Tint settings from the Configuration menu.
s Image - Color Saturation, Tint p.85
Images appear dark
Check
Remedy
Is the image brightness set correctly?
Adjust the Brightness and Power Consumption settings from the Configuration menu.
s Image - Brightness p.85
s ECO - Power Consumption p.99
Is the contrastg adjusted correctly?
Adjust the Contrast setting from the Configuration menu.
s Image - Contrast p.85
Is it time to replace the lamp?
When the lamp is nearly ready for replacement, the images become darker and the color quality becomes poorer. When
this happens, replace the lamp with a new lamp.
s "Replacing the Lamp" p.121
Are you using the projector at a high altitude or in a location subject The screen may become dark when using at high altitude or in a location subject to high temperatures. Although you
to high temperatures?
cannot make Power Consumption settings at this time, you can continue to use the projector.
Is it projecting outside of the recommended projection distance
range?
The image becomes darker if the projection distance is too large. Setup within the recommended range.
s "Screen Size and Projection Distance" p.128
Problem Solving
115
Problems when Projection Starts
The projector does not turn on
Check
Remedy
Did you press the [t] power button?
Press the [t] power button to turn the power on.
Are the indicators switched off?
The power cord is not connected correctly or power is not being fully supplied.
Disconnect and then reconnect the power cord.
s "From Installation to Projection" p.34
Check that your electrical outlet or power source is functioning correctly.
Do the indicators turn on and off when the power cord is touched? There is probably a poor contact in the power cord, or the power cord may be defective. Reinsert the power cord. If this
does not solve the problem, stop using the projector, disconnect the power cord from the electrical outlet, and contact
your local dealer or the nearest address provided in the Epson Projector Contact List.
s Epson Projector Contact List
Is the Control Panel Lock set to Full Lock?
Press the [t] power button on the remote control. If you do not want to use Control Panel Lock, change the setting to
Off.
s Settings - Control Panel Lock p.88
Is remote control operation restricted?
Check the Remote Receiver from the Configuration menu.
s Settings - Remote Receiver p.88
Other Problems
No sound can be heard or the sound is faint
Check
Check that the audio/video cable is securely attached to both the
projector and audio source.
Remedy
Disconnect the cable from the Audio port, and then reconnect the cable.
Is the volume for the projector or the connected equipment set to the Adjust the volume so that sound can be heard.
minimum?
s Settings - Volume p.88
s "Adjusting the Volume" p.46
Problem Solving
116
Check
Remedy
Is A/V Mute active?
Press the [A/V Mute] button on the remote control to cancel A/V Mute.
s "Hiding the Image and Sound Temporarily (A/V Mute)" p.57
Is the audio cable's specification "No resistance"?
When using a commercially available audio cable, make sure it is labeled "No resistance".
Is it connected with an HDMI cable?
If no audio is output when connecting via an HDMI cable, set the connected equipment to PCM output.
Is Output audio from the projector selected?
(Only when projecting in USB Display, when projecting one screen
in EasyMP Network Projection, or one screen in EasyMP Multi PC
Projection.)
Click All Programs - EPSON Projector - Epson USB Display - Epson USB Display Vx.xx Settings, and then select
Output audio from the projector.
When projecting in EasyMP Network Projection or EasyMP Multi PC Projection: In the software you are using, select
Output audio from the projector from the Audio Output tab in Set Options.
There is noise in the audio (when projecting EasyMP Network Projection, EasyMP MultiPC Projection, USB Display, or Quick Wireless
Connection)
Check
Is the volume for the computer set to the minimum while the
projector is set to the maximum?
Remedy
If the volume for the computer is set to the minimum while the projector is set to the maximum, the noise may be mixed.
Turn up the computer's volume and turn down the projector's volume.
The remote control does not work
Check
Remedy
Is the remote control light-emitting area pointing towards the
remote receiver on the projector during operation?
Point the remote control towards the remote receiver.
s "Remote control operating range" p.20
Is the remote control too far from the projector?
The operating range for the remote control is about six meters.
s "Remote control operating range" p.20
Is direct sunlight or strong light from fluorescent lamps shining onto Set the projector up in a location where strong light does not shine onto the remote receiver.
the remote receiver?
s Settings - Remote Receiver p.88
Is the correct setting for the Remote Receiver selected?
Check the Remote Receiver from the Configuration menu.
s Settings - Remote Receiver p.88
Are the batteries dead or have the batteries been inserted correctly? Make sure the batteries are inserted correctly or replace the batteries with new ones if necessary.
s "Replacing the remote control batteries" p.19
Problem Solving
117
I want to change the language for messages and menus
Check
Change the Language setting.
Remedy
Adjust the Language setting from the Configuration menu.
s Extended - Language p.89
Mail is not received even if a problem occurs in the projector
Check
Remedy
Is Standby Mode set to Communication On?
To use the Mail Notification function when the projector is in standby, set Communication On in Standby Mode from
the Configuration menu.
s ECO - Standby Mode p.99
Did a fatal abnormality occur and the projector come to a sudden
stop?
If the abnormal state continues, contact your local dealer or the nearest address provided in the Epson Projector Contact
List.
s Epson Projector Contact List
Is power being supplied to the projector?
Check that your electrical outlet or power source is functioning correctly.
Is Mail Notification function set correctly in the Configuration
menu?
An error notification email is sent according to the Mail settings in the Configuration menu. Check if it is set correctly.
s "Mail menu" p.97
Cannot change settings using a Web browser
Check
Are the user ID and password correct?
Remedy
Enter "EPSONWEB" as the user ID. This cannot be changed. Enter the user ID even if the password setting is
disabled. Enter the characters set for the Web Control Password as the password. The initial password is
"admin".
Maintenance
This chapter provides information on maintenance procedures to ensure the best level of performance from the projector for a long time to come.
Cleaning
You should clean the projector if it becomes dirty or if the quality of
projected images starts to deteriorate.
Caution
Turn off the projector's power before cleaning. Otherwise, it could cause an
electric shock.
Cleaning the Projector's Surface
Clean the projector's surface by wiping it gently with a soft cloth.
If the projector is particularly dirty, moisten the cloth with water containing
a small amount of neutral detergent, and then firmly wring the cloth dry
before using it to wipe the projector's surface.
Attention
Do not use volatile substances such as wax, alcohol, or thinner to clean the
projector's surface. The quality of the case may change or become discolored.
Cleaning the Lens
Use a commercially available cloth for cleaning glasses to gently wipe the
lens.
Warning
Do not use sprays that contain flammable gas to remove dust and lint from the
lens. The projector may catch fire due to the high internal temperature of the
lamp.
119
Attention
Do not rub the lens with harsh materials or subject the lens to shocks as it
can easily become damaged.
Cleaning the Air Filter
Clean the air filter and the air intake vent when the following message is
displayed.
"The projector is overheating. Make sure nothing is blocking the air vent,
and clean or replace the air filter."
Attention
• If dust collects on the air filter, it can cause the internal temperature of the
projector to rise, and this can lead to problems with operation and shorten
the optical engine's service life. Clean the air filter immediately when the
message is displayed.
• Do not rinse the air filter in water. Do not use detergents or solvents.
Cleaning
a
120
• If a message is frequently displayed, even after cleaning, it is time to
replace the air filter. Replace it with a new air filter.
s "Replacing the Air Filter" p.124
• It is recommended that you clean these parts at least once every
three months. Clean them more often than this if using the projector
in a particularly dusty environment.
Replacing Consumables
This section explains how to replace the lamp and the air filter.
Replacing the Lamp
Lamp replacement period
It is time to replace the lamp when:
• The following message is displayed.
"Time to replace the lamp. Please contact your Epson projector reseller or
visit www.epson.com to purchase."
121
• The projected image gets darker or starts to deteriorate.
Attention
• The lamp replacement message is set to appear after the following time
periods in order to maintain the initial brightness and quality of the projected
images.
When Power Consumption is set to Normal: About 4,900 hours
When Power Consumption is set to ECO: About 5,900 hours
s ECO - Power Consumption p.99
• If you continue to use the lamp after the replacement period has passed, the
possibility that the lamp may explode increases. When the lamp replacement
message appears, replace the lamp with a new one as soon as possible, even if
it is still working.
• Do not repeatedly turn off the power and immediately back on. Turning the
power on and off frequently may shorten the lamp's operating life.
• Depending on the characteristics of the lamp and the way it has been used,
the lamp may become darker or stop working before the lamp warning
message appears. You should always have a spare lamp unit ready in case it is
needed.
The message is displayed for 30 seconds.
• The power indicator is flashing blue, and the lamp indicator is flashing
orange.
• We recommend the use of genuine EPSON option lamps. The use of nongenuine lamps may affect projection quality and safety. Any damage or
malfunction caused by the use of non-genuine lamps may not be covered by
Epson's warranty.
How to replace the lamp
The lamp can be replaced even when the projector is suspended from a
ceiling.
Replacing Consumables
122
Warning
• When replacing the lamp because it has stopped illuminating, there is a
possibility that the lamp may be broken. If replacing the lamp of a projector
which has been installed on the ceiling, you should always assume that the
lamp is cracked, and you should stand to the side of the lamp cover, not
underneath it. Remove the lamp cover gently. Be careful when removing the
lamp cover as shards of glass may fall out and could cause an injury. If any
shards of glass get into your eyes or mouth, contact your local physician
immediately.
• Never disassemble or remodel the lamp. If a modified or disassembled lamp
is installed in the projector and used, it could cause a fire, electric shock, or
an accident.
Caution
Wait until the lamp has cooled down sufficiently before removing the lamp
cover. If the lamp is still hot, burns or other injuries may result. It takes about
one hour after the power has been turned off for the lamp to be cool enough.
a
After you turn off the projector's power and the confirmation
buzzer beeps twice, disconnect the power cord.
b
Wait until the lamp has sufficiently cooled down, and then remove
the lamp cover at the top of the projector.
Loosen the Lamp cover fixing screw with the screwdriver supplied
with the new lamp unit or a cross-head screwdriver. Then slide the
lamp cover straight forward and lift it to remove.
c
Loosen the two lamp fixing screws.
Replacing Consumables
d
123
e
Install the new lamp.
f
Replace the lamp cover.
Insert the new Lamp along the guide rail in the correct direction so
that it fits in place, push in firmly, and once it is fully inserted
tighten the two screws.
Grip the raised section of the old lamp and remove it.
If the Lamp is cracked, replace it with a new lamp, or contact your
local dealer for further advice.
s Epson Projector Contact List
Replacing Consumables
124
Replacing the Air Filter
Air filter replacement period
If the message is displayed frequently even though the air filter has been
cleaned, replace the air filter.
How to replace the air filter
The air filter can be replaced even when the projector is suspended from a
ceiling.
Attention
• Make sure you install the lamp securely. If the lamp cover is removed, the
lamps turn off automatically as a safety precaution. If the lamp or the lamp
cover is not installed correctly, the lamp will not turn on.
• This product includes a lamp component that contains mercury (Hg). Please
consult your local regulations regarding disposal or recycling. Do not dispose
of it with normal waste.
a
After you turn off the projector's power and the confirmation
buzzer beeps twice, disconnect the power cord.
b
Open the air filter cover.
c
Remove the air filter.
Resetting the lamp hours
The projector records how long the lamp is turned on and a message and
indicator notify you when it is time to replace the lamp. After replacing the
lamp, make sure you reset the Lamp Hours from the Reset menu.
s Reset - Reset Lamp Hours p.101
a
Only reset the Lamp Hours after the lamp has been replaced.
Otherwise the lamp replacement period is not indicated correctly.
Grip the air filter cover tab and pull it straight out.
Replacing Consumables
125
e
Close the air filter cover.
a
d
Install the new air filter.
Slide the air filter from the outside and press in until it firmly clicks
into place.
Dispose of used air filters properly in accordance with your
local regulations.
Filter frame: ABS
Filter: Polyurethane foam
Appendix
Optional Accessories and Consumables
The following optional accessories and consumables are available. Please
purchase these products as and when needed. The following list of optional
accessories and consumables is current as of: May 2013. Details of
accessories are subject to change without notice and availability may vary
depending on the country of purchase.
Optional Accessories
Interactive Unit ELPIU01
Use when operating the computer screen on the projection surface.
Wireless LAN unit ELPAP07
Use this to project images from a computer via a wireless communication.
Quick Wireless Connection USB Key ELPAP09
Use when you want to quickly establish one-to-one connection between the
projector and a computer with Windows installed.
Document Camera ELPDC06/ELPDC11/ELPDC12/ELPDC20
Use when projecting images such as books, OHP documents, or slides.
Soft carrying case ELPKS67
A soft case to carry the projector.
50" portable screen
ELPSC32
A compact screen that can be carried easily. (Aspect Ratiog 4:3)
60" portable screen ELPSC27
80" portable screen ELPSC28
100" screen ELPSC29
Portable roll-type screens. (aspect ratio 4:3)
70" portable screen
80" portable screen
90" portable screen
ELPSC23
ELPSC24
ELPSC25
Portable roll-type screens. (aspect ratio 16:10)
127
53" portable screen
64" portable screen
ELPSC30
ELPSC31
Portable magnetic screens. (aspect ratio 4:3)
Multi-aspect screen ELPSC26
This is a portable multi-aspect screen.
Computer cable ELPKC02
(1.8 m - for mini D-Sub15-pin/mini D-Sub 15pin)
Computer cable ELPKC09
(3 m - for mini D-Sub15-pin/mini D-Sub 15pin)
Computer cable ELPKC10
(20 m - for mini D-Sub15-pin/mini D-Sub 15pin)
Component video cable ELPKC19
(3 m - for mini D-Sub 15-pin/RCA male^3)
Use to connect a component videog source.
Ceiling pipe (450 mm) * ELPFP13
Ceiling pipe (700 mm) * ELPFP14
Use when installing the projector on a high ceiling.
Ceiling mount* ELPMB23
Use when installing the projector on a ceiling.
Special expertise is required to suspend the projector from a ceiling. Contact
your local dealer or the nearest address provided in the Epson Projector
Contact List.
s Epson Projector Contact List
*
Consumables
Lamp unit ELPLP78
Use as a replacement for used lamps.
Air filter ELPAF32
Use as a replacement for used air filters.
Screen Size and Projection Distance
128
Projection Distance (For EB-X25)
A
4:3 Screen Size
Minimum (Wide) to Maximum
(Tele)
B
60"
120x91
171 - 206
-10
80"
160x120
229 - 275
-13
100"
200x150
287 - 345
-16
150"
300x230
432 - 519
-24
200"
410x300
577 - 693
-32
250"
510x380
722 - 867
-40
300"
610x460
867 - 1041
-48
Unit: cm
A
16:9 Screen Size
A Projection distance
B Distance from the center of the receiver's lens to the base of the screen
(or to the top of the screen, if suspended from a ceiling)
C Center of lens
Unit: cm
A
4:3 Screen Size
Minimum (Wide) to Maximum
(Tele)
B
30"
61x46
84 - 101
-5
40"
81x61
113 - 136
-6
50"
100x76
142 - 171
-8
Minimum (Wide) to Maximum
(Tele)
B
30"
66x37
91 - 110
1
40"
89x50
123 - 148
1
50"
110x62
155 - 186
2
60"
130x75
186 - 224
2
80"
180x100
249 - 300
3
100"
220x120
313 - 376
3
150"
330x190
471 - 566
5
200"
440x250
629 - 755
7
250"
550x310
787 - 945
9
275"
610x340
866 - 1040
10
Screen Size and Projection Distance
129
Projection Distance (For EB-X22/EB-X21/EB-X20/
EB-X17)
A
4:3 Screen Size
Minimum (Wide) to Maximum
(Tele)
B
50"
100x76
150 - 180
-8
60"
120x91
180 - 217
-10
80"
160x120
241 - 290
-14
100"
200x150
302 - 363
-17
150"
300x230
454 - 546
-25
200"
410x300
607 - 729
-34
250"
510x380
759 - 912
-42
300"
610x460
912 - 1095
-51
Unit: cm
A
16:9 Screen Size
A Projection distance
B Distance from the center of the receiver's lens to the base of the screen
(or to the top of the screen, if suspended from a ceiling)
C Center of lens
Unit: cm
A
4:3 Screen Size
Minimum (Wide) to Maximum
(Tele)
B
30"
61x46
89 - 107
-5
40"
81x61
119 - 143
-7
Minimum (Wide) to Maximum
(Tele)
B
30"
66x37
97 - 117
1
40"
89x50
130 - 156
1
50"
110x62
163 - 196
1
60"
130x75
196 - 236
1
80"
180x100
263 - 316
2
100"
220x120
329 - 396
2
150"
330x190
495 - 595
3
200"
440x250
661 - 794
5
250"
550x310
827 - 994
6
275"
610x340
910 - 1093
6
Screen Size and Projection Distance
130
Projection Distance (For EB-W22)
A
4:3 Screen Size
Minimum (Wide) to Maximum
(Tele)
B
60"
120x91
190 - 229
-8
70"
142x107
222 - 267
-10
80"
160x120
255 - 306
-11
100"
200x150
319 - 383
-14
150"
300x230
480 - 577
-20
200"
410x300
641 - 770
-27
280"
570x430
898 - 1079
-38
Unit: cm
A
16:9 Screen Size
A Projection distance
B Distance from the center of the receiver's lens to the base of the screen
(or to the top of the screen, if suspended from a ceiling)
C Center of lens
Unit: cm
A
4:3 Screen Size
Minimum (Wide) to Maximum
(Tele)
B
30"
61x46
94 - 113
-4
40"
81x61
126 - 152
-5
50"
100x76
158 - 190
-7
Minimum (Wide) to Maximum
(Tele)
B
32"
71x40
91 - 109
-2
35"
78x44
99 - 120
-2
40"
89x50
114 - 137
-2
50"
110x62
143 - 172
-3
60"
130x75
172 - 208
-3
70"
155x87
202 - 243
-4
80"
180x100
231 - 278
-4
100"
220x120
289 - 348
-5
150"
330x190
435 - 523
-8
200"
440x250
582 - 699
-11
310"
690x390
903 - 1084
-17
Screen Size and Projection Distance
131
Unit: cm
A
16:10 Screen Size
Minimum (Wide) to Maximum
(Tele)
B
33"
71x44
91 - 110
-4
35"
76x47
97 - 117
-4
40"
86x54
111 - 134
-5
50"
110x67
139 - 168
-6
60"
130x81
168 - 202
-7
80"
170x110
225 - 270
-10
100"
220x130
281 - 338
-12
150"
320x200
424 - 509
-18
200"
430x270
566 - 680
-24
320"
690x430
907 - 1089
-39
Projection Distance (For EB-S21/EB-S17)
A Projection distance
B Distance from the center of the receiver's lens to the base of the screen
(or to the top of the screen, if suspended from a ceiling)
C Center of lens
Unit: cm
4:3 Screen Size
A
B
Minimum (Wide) to
Maximum (Tele)
Wide
30"
61x46
88 - 119
-5
50"
100x76
147 - 200
-8
60"
120x91
177 - 240
-10
Screen Size and Projection Distance
4:3 Screen Size
132
A
B
Minimum (Wide) to
Maximum (Tele)
Wide
70"
142x107
207 - 280
-12
80"
160x120
237 - 321
-13
100"
200x150
297 - 401
-17
150"
300x230
446 - 603
-25
200"
410x300
595 - 805
-33
Unit: cm
16:9 Screen Size
A
B
Minimum (Wide) to
Maximum (Tele)
Wide
28"
62x35
89 - 121
1
30"
66x37
96 - 130
1
50"
110x62
161 - 218
1
60"
130x75
193 - 262
2
70"
155x87
226 - 306
2
80"
180x100
258 - 349
2
100"
220x120
323 - 437
3
150"
330x190
486 - 657
4
200"
440x250
649 - 877
5
Supported Monitor Displays
133
For EB-S21/EB-S17
Supported Resolutions
Computer signals (analog RGB)
For EB-X25/EB-W22/EB-X22/EB-X21/EB-X20/EB-X17
Signal
Refresh Rate (Hz)
Resolution (dots)
VGA
60/72/75/85
640x480
SVGA
56/60/72/75/85
800x600
XGA
60/70/75/85
1024x768
WXGA
60
1280x768
60
1366x768
60/75/85
1280x800
WXGA+
60/75/85
1440x900
WXGA++
60
1600x900
SXGA
70/75/85
1152x864
60/75/85
1280x1024
60/75/85
1280x960
SXGA+
60/75
1400x1050
WSXGA+*1,2
60
1680x1050
UXGA
60
1600x1200
MAC13"
67
640x480
MAC16"
75
832x624
MAC19"
75
1024x768
59
1024x768
75
1152x870
MAC21"
*1 EB-W22 only
*2 Only compatible when Wide is selected as the Resolution from the
Configuration menu.
Signal
Refresh Rate (Hz)
Resolution (dots)
VGA
60/72/75/85
640x480
SVGA
56/60/72/75/85
800x600
XGA
60/70/75/85
1024x768
WXGA
60
1280x768
60
1366x768
60/75
1280x800
WXGA+
60
1440x900
SXGA
70/75
1152x864
60
1280x1024
60
1280x960
SXGA+
60
1400x1050
MAC13"
67
640x480
MAC16"
75
832x624
MAC19"
75
1024x768
59
1024x768
75
1152x870
MAC21"
Even when signals other than those mentioned above are input, it is likely
that the image can be projected. However, not all functions may be
supported.
Component video
Signal
Refresh Rate (Hz)
Resolution (dots)
SDTV (480i)
60
720x480
SDTV (576i)
50
720x576
Supported Monitor Displays
134
Signal
Refresh Rate (Hz)
Resolution (dots)
Signal
Refresh Rate (Hz)
Resolution (dots)
SDTV (480p)
60
720x480
SDTV (480i/480p)
60
720x480
SDTV (576p)
50
720x576
SDTV (576i/576p)
50
720x576
HDTV (720p)
50/60
1280x720
HDTV (720p)
50/60
1280x720
HDTV (1080i)
50/60
1920x1080
HDTV (1080i)
50/60
1920x1080
HDTV (1080p)
24/30/50/60
1920x1080
*1 EB-X25/EB-W22/EB-X22/EB-X21/EB-X20/EB-X17 only
*2 EB-W22 only
Composite video
Signal
Refresh Rate (Hz)
Resolution (dots)
TV (NTSC)
60
720x480
TV (SECAM)
50
720x576
TV (PAL)
50/60
720x576
Input signal from the HDMI port
Signal
Refresh Rate (Hz)
Resolution (dots)
VGA
60
640x480
SVGA
60
800x600
XGA
60
1024x768
WXGA
60
1280x800
60
1366x768
WXGA+
60
1440x900
WXGA++*1
60
1600x900
60
1280x960
60
1280x1024
SXGA+
60
1400x1050
UXGA*1
60
1600x1200
WSXGA+*2
60
1680x1050
SXGA
Specifications
135
Projector General Specifications
EB-S21/EB-S17
Product name
EB-X22/EB-X21/EB-X20/EBX17
0.55"
LCD panel size
0.55"
0.63"
480,000
786,432
1,024,000
786,432
SVGA (800 (W) x 600 (H) dots) x XGA (1024 (W) x 768 (H) dots)x WXGA (1280 (W) x 800 (H) dots) XGA (1024 (W) x 768 (H) dots)x
3
3
x3
3
Resolution
Manual
Focus adjustment
Digital (1-1.35)
Zoom adjustment
Manually (1-1.2)
UHE lamp, 200 W Model No.: ELPLP78
Lamp
5W
Max. audio output
1
Speaker
100-240 V AC±10%, 50/60 Hz 2.9-1.3 A
Power supply
100 to 120 V area
Operating: 284 W
Standby power consumption (Communication On): 3.0 W
Standby power consumption (Communication Off): 0.24 W
220 to 240 V area
Operating: 273 W
Standby power consumption (Communication On): 3.1 W
Standby power consumption (Communication Off): 0.29 W
Altitude 0 to 3,000 m
Operating altitude
+5 to +35°C (No condensation) (Altitude 0 to 2,286 m)
+5 to +30°C (No condensation) (Altitude above 2,286 m)
Operating temperature
-10 to +60°C (No condensation)
Storage temperature
Connectors
0.59" Wide
Polysilicon TFT active matrix
Display method
Mass
EB-X25
297 (W) x 89 (H) x 244 (D) mm
Dimensions
Power
con‐
sumption
EB-W22
Approx. 2.5 kg
Computer1 port
Approx. 2.6 kg
1
Mini D-Sub15-pin (female)
Specifications
136
Computer2 port
1
Video port
1
RCA pin jack
S-Video port
1
Mini DIN 4-pin
Audio1 port
1
Audio2 port
1
Audio-L/R port
1
RCA pin jack x 2 (L-R)
Audio Out port
1
Stereo mini jack
Monitor Out port
1
Mini D-Sub15-pin (female)
HDMI port
1
HDMI (Audio is only supported by PCM)
1
USB connector (Type A)
USB-B port *2
1
USB connector (Type B)
LAN Port *3
1
RJ-45
RS-232C port
1
Mini D-Sub 9-pin (male)
USB-A port *1,
2
*1 EB-X21/EB-S21/EB-X17/EB-S17 only
*2 Supports USB 2.0. However, USB ports are not guaranteed to operate all devices that support USB.
*3 EB-X25/EB-W22/EB-X22/EB-X20 only
Stereo mini jack
Specifications
This product is also designed for IT power distribution system with phase-to-phase voltage 230V.
Angle of tilt
If you use the projector tilted at an angle of more than 30˚ it could be damaged and cause an accident.
137
Specifications
138
DECLARATION of CONFORMITY
According to 47CFR, Part 2 and 15
Class B Personal Computers and Peripherals; and/or
CPU Boards and Power Supplies used with Class B Personal Computers
We:
Located at:
Tel:
Epson America, Inc.
3840 Kilroy Airport Way
MS: 3-13
Long Beach, CA 90806
562-981-3840
Declare under sole responsibility that the product identified herein,
complies with 47CFR Part 2 and 15 of the FCC rules as a Class B digital
device. Each product marketed, is identical to the representative unit tested
and found to be compliant with the standards. Records maintained continue
to reflect the equipment being produced can be expected to be within the
variation accepted, due to quantity production and testing on a statistical
basis as required by 47CFR 2.909. Operation is subject to the following two
conditions : (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that
may cause undesired operation.
Trade Name:
EPSON
Type of Product:
LCD Projector
Model:
H567C/H568C/H569C/H570C/H571C/H572C/
H573C/H574C/H575C/H576C/H577C/H578C/
H579C/H580C/H581C/H582C/H583C
FCC Compliance Statement
For United States Users
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause interference to radio
and television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING
The connection of a non-shielded equipment interface cable to this
equipment will invalidate the FCC Certification or Declaration of this
device and may cause interference levels which exceed the limits established
by the FCC for this equipment. It is the responsibility of the user to obtain
and use a shielded equipment interface cable with this device. If this
equipment has more than one interface connector, do not leave cables
connected to unused interfaces. Changes or modifications not expressly
approved by the manufacturer could void the user's authority to operate the
equipment.
Appearance
139
242
297
93
31.8
A
B
244
123.4
35.7
12
89.5
15.9
99.6
Center of lens
Distance from center of lens to suspension bracket fixing point
3-M4 x 9
Units: mm
Glossary
140
This section briefly explains the difficult terms that are not explained in the text of this guide. For details, refer to other commercially available publications.
Ad hoc mode
A method of wireless LAN connection that communicates with wireless LAN clients without using an access point.
AMX Device Discovery
AMX Device Discovery is a technology developed by AMX to facilitate AMX control systems for easy operation of the target equipment.
Epson have implemented this protocol technology, and have provided a setting to enable the protocol function (ON). See the AMX Web site for more
details.
s http://www.amx.com/
Aspect Ratio
The ratio between an image's length and its height. Screens with a horizontal:vertical ratio of 16:9, such as HDTV screens, are known as wide screens.
SDTV and general computer displays have an aspect ratio of 4:3.
Component Video
A method that separates the video signal into a luminance component (Y), and a blue minus luminance (Cb or Pb) and a red minus luminance (Cr or
Pr).
Composite video
A method that combines the video signal into a luminance component and a color component for transmission down a single cable.
Contrast
The relative brightness of the light and dark areas of an image can be increased or decreased to make text and graphics stand out more clearly, or to
make them appear softer. Adjusting this particular property of an image is called contrast adjustment.
DHCP
An abbreviation of Dynamic Host Configuration Protocol, this protocol automatically assigns an IP addressg to equipment connected to a network.
Gateway Address
This is a server (router) for communicating across a network (subnet) divided according to subnet maskg.
HDCP
HDCP is an abbreviation for High-bandwidth Digital Content Protection. It is used to prevent illegal copying and protect copyrights by encrypting
digital signals sent over DVI and HDMI ports. Because the HDMI port on this projector supports HDCP, it can project digital images protected by
HDCP technology. However, the projector may not be able to project images protected with updated or revised versions of HDCP encryption.
HDTV
An abbreviation for High-Definition Television that refers to high-definition systems which satisfy the following conditions.
• Vertical resolution of 720p or 1080i or greater (p = Progressiveg, i = Interlaceg)
• Screen aspect ratiog of 16:9
Infrastructure mode
A method for wireless LAN connection in which devices communicate through access points.
Interlace
Transmits information needed to create one screen by sending every other line, starting from the top of the image and working down to the bottom.
Images are more likely to flicker because one frame is displayed every other line.
IP Address
A number to identify a computer connected to a network.
Progressive
Projects information to create one screen at a time, displaying the image for one frame. Even though the number of scan lines is the same, the amount
of flicker in images decreases because the volume of information has doubled compared with an interlace system.
Refresh Rate
The light-emitting element of a display maintains the same luminosity and color for an extremely short time. Because of this, the image must be
scanned many times per second to refresh the light-emitting element. The number of refresh operations per second is called the Refresh Rate and is
expressed in hertz (Hz).
Glossary
141
SDTV
An abbreviation for Standard Definition Television that refers to standard television systems which do not satisfy the conditions for HDTVg HighDefinition Television.
SNMP
An abbreviation for Simple Network Management Protocol, which is the protocol for monitoring and controlling devices such as routers and
computers connected to a TCP/IP network.
sRGB
An international standard for color intervals that was formulated so that colors that are reproduced by video equipment can be handled easily by
computer operating systems (OS) and the Internet. If the connected source has an sRGB mode, set both the projector and the connected signal source
to sRGB.
SSID
SSID is identification data for connecting to another device on a wireless LAN. Wireless communication is possible between devices that correspond
to SSID.
Subnet Mask
This is a numerical value that defines the number of bits used for the network address on a divided network (subnet) from the IP address.
SVGA
A screen size standard with a resolution of 800 (horizontal) x 600 (vertical) dots.
S-Video
A method that separates the video signal into a luminance component (Y) and a color component (C).
SXGA
A screen size standard with a resolution of 1,280 (horizontal) x 1,024 (vertical) dots.
Sync.
The signals output from computers have a specific frequency. If the projector frequency does not match this frequency, the resulting images are not of
a good quality. The process of matching the phases of these signals (the relative position of the crests and the troughs in the signal) is called
Synchronization. If the signals are not synchronized, flickering, blurriness, and horizontal interference occur.
Tracking
The signals output from computers have a specific frequency. If the projector frequency does not match this frequency, the resulting images are not of
a good quality. The process of matching the frequency of these signals (the number of crests in the signal) is called Tracking. If Tracking is not carried
out correctly, wide vertical stripes appear in the signal.
Trap IP Address
This is the IP addressg for the destination computer used for error notification in SNMP.
VGA
A screen size standard with a resolution of 640 (horizontal) x 480 (vertical) dots.
XGA
A screen size standard with a resolution of 1,024 (horizontal) x 768 (vertical) dots.
General Notes
All rights reserved. No part of this publication may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without the prior written permission of Seiko
Epson Corporation. No patent liability is assumed with respect to the use of the
information contained herein. Neither is any liability assumed for damages resulting
from the use of the information contained herein.
Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this
product or third parties for damages, losses, costs, or expenses incurred by the
purchaser or third parties as a result of: accident, misuse, or abuse of this product or
unauthorized modifications, repairs, or alterations to this product, or (excluding the
U.S.) failure to strictly comply with Seiko Epson Corporation's operating and
maintenance instructions.
Seiko Epson Corporation shall not be liable against any damages or problems arising
from the use of any options or any consumable products other than those designated as
Original Epson Products or Epson Approved Products by Seiko Epson Corporation.
The contents of this guide may be changed or updated without further notice.
Illustrations in this guide and the actual projector may differ.
Restriction of Use
When this product is used for applications requiring high reliability/safety such as
transportation devices related to aviation, rail, marine, automotive etc.; disaster
prevention devices; various safety devices etc; or functional/precision devices etc, you
should use this product only after giving consideration to including fail-safes and
redundancies into your design to maintain safety and total system reliability. Because
this product was not intended for use in applications requiring extremely high
reliability/safety such as aerospace equipment, main communication equipment,
nuclear power control equipment, or medical equipment related to direct medical care
etc, please make your own judgment on this product’s suitability after a full evaluation.
142
About Notations
Microsoft
Microsoft
Microsoft
Microsoft
Microsoft
® Windows
® 2000 operating system
Windows XP operating system
® Windows®Vista operating system
® Windows 7 operating
®
® Windows® 8 operating system
system
®
®
In this guide, the operating systems above are referred to as "Windows
2000," "Windows XP," "Windows Vista," "Windows 7," and "Windows 8".
Furthermore, the collective term Windows may be used to refer to
Windows 2000, Windows XP, Windows Vista, Windows 7, and Windows 8,
and multiple versions of Windows may be referred to as, for example,
Windows 2000/XP/Vista, with the Windows notation omitted.
Mac
Mac
Mac
Mac
Mac
Mac
OS
OS
OS
OS
OS
OS
X
X
X
X
X
X
10.3.x
10.4.x
10.5.x
10.6.x
10.7.x
10.8.x
In this guide, the operating systems above are referred to as "Mac OS X
10.3.9," "Mac OS X 10.4.x," "Mac OS X 10.5.x," "Mac OS X 10.6.x," "Mac OS
X 10.7.x," and "Mac OS X 10.8.x". Furthermore, the collective term "Mac
OS" is used to refer to them.
General Notes
143
General Notice:
IBM, DOS/V, and XGA are trademarks or registered trademarks of International
Business Machines Corporation.
Mac and Mac OS are trademarks of Apple Inc.
App Store is a service mark of Apple Inc.
Google play is a trademark of Google Inc.
Microsoft, Windows, Windows Vista, PowerPoint, and Windows logo are trademarks
or registered trademarks of Microsoft Corporation in the United States and/or other
countries.
WPA and WPA2 are registered trademarks of Wi-Fi Alliance.
HDMI and High-Definition Multimedia Interface are the trademarks or registered
™
™
trademarks of HDMI Licensing LLC.
EPSON and ELPLP are trademarks or registered trademarks of the SEIKO EPSON
CORPORATION.
PJLink trademark is a trademark applied for registration or is already registered in
Japan, the United States of America and other countries and areas.
Other product names used herein are also for identification purposes only and may be
trademarks of their respective owners. Epson disclaims any and all rights in those
marks.
©SEIKO EPSON CORPORATION 2013. All rights reserved.
Index
144
A
A/V Mute ...................................................... 57
A/V Mute Timer ........................................ 100
A/V Settings ................................................. 90
Abs. Color Temp. ........................................ 85
Air exhaust vent ........................................... 11
Air filter replacement period ................... 124
AMX Device Discovery .............................. 98
Aspect ...................................................... 47, 87
Audio1 port .................................................. 13
Audio2 port .................................................. 13
Audio-L/R port ............................................ 13
Auto Iris .................................................. 47, 86
Auto Setup .................................................... 86
Auto V-Keystone ......................................... 88
Computer input port ................................... 13
Computer Port ............................................. 13
Configuration menu .................................... 82
Connection mode ........................................ 94
Consumables .............................................. 127
Continuous play ........................................... 57
Contrast ........................................................ 85
Control panel ............................................... 15
Control Panel Lock ...................................... 68
Control panel lock ....................................... 88
Crestron RoomView ............................. 75, 76
Cross .............................................................. 60
D
DHCP ............................................................ 96
Direct Power On .......................................... 90
Display ........................................................... 89
Display Background .................................... 89
Display order ................................................ 57
Display settings ............................................ 57
Document Camera .................................... 127
Dynamic ........................................................ 46
B
Basic menu ....................................................
Blackboard ....................................................
Bonjour .........................................................
Brightness .....................................................
93
46
98
85
C
Ceiling ..................................................... 22, 90
Ceiling mount fixing points ....................... 14
Cleaning ...................................................... 119
Cleaning the air filter and air intake vent
........................................................................ 119
Cleaning the Projector's Surface .............. 119
Color Adjustment ........................................ 86
Color Mode ............................................ 46, 85
Color Saturation .......................................... 85
E
EasyMP Monitor .......................................... 70
ECO Display ............................................... 100
ECO menu .................................................... 99
Email Address .............................................. 97
ESC/VP21 ..................................................... 73
Extended menu ............................................ 89
E-Zoom ......................................................... 59
F
Focus ring ..................................................... 12
Foot adjust lever ........................................... 12
Freeze ............................................................. 58
Front ........................................................ 22, 90
Front adjustable foot ................................... 12
Full Lock ....................................................... 67
G
Gateway Address ................................... 94, 96
H
HDMI port ................................................... 13
HDMI Video Range .................................... 87
Help function ............................................. 103
High Altitude Mode .................................... 90
H-Keystone adjuster .................................... 41
Horizontal keystone adjuster ................. 8, 41
How to replace the air filter ..................... 124
How to replace the lamp ........................... 121
I
Image menu .................................................. 85
Indicators .................................................... 104
Info menu ................................................... 100
Input Signal .................................................. 87
Input signal ................................................. 100
IP Address ..................................................... 97
K
Keystone ........................................................ 88
Index
145
L
P
Lamp cover ................................................... 12
Lamp hours .......................................... 99, 100
Lamp indicator ........................................... 104
Lamp replacement period ........................ 121
LAN port ....................................................... 14
Language ....................................................... 90
Lens Cover Timer ...................................... 100
Light Optimizer ........................................... 99
Part Names and Functions ......................... 11
Password protect .......................................... 65
Password Protect Sticker ............................ 66
Pattern ........................................................... 89
PC Free .................................................... 53, 56
Photo ............................................................. 46
PJLink ............................................................ 75
PJLink Password .......................................... 93
Pointer ........................................................... 58
Pointer shape ................................................ 88
Port Number ................................................ 97
Position ......................................................... 86
Power indicator .......................................... 104
Power inlet .................................................... 13
Power On Protect ........................................ 65
Presentation ........................................... 46, 52
Problem Solving ......................................... 104
Progressive .................................................... 87
Projection ...................................................... 90
Projection distance .................................... 128
Projector keyword ....................................... 93
Projector Name ............................................ 93
Projector Setup ............................................. 70
M
Mail Notification ................................... 72, 97
Mail Notification menu .............................. 97
Message Broadcasting ........................... 70, 98
Messages ....................................................... 89
Monitor Displays ....................................... 133
Mouse pointer .............................................. 60
N
Network Configuration ..............................
Network information ..................................
Network Menu .............................................
Network Protection .....................................
Noise Reduction ...........................................
91
91
91
65
87
O
Operating temperature ............................. 135
Operation ...................................................... 90
Optional accessories .................................. 127
Overheating ................................................ 105
Q
Quick Corner ............................................... 88
Quick Wireless Connection USB Key .... 127
R
Reading Mail ................................................ 72
Rear .......................................................... 22, 90
Rear feet ........................................................ 15
Rear screen .................................................... 22
Refresh Rate ................................................ 100
Remote control ............................................ 16
Remote receiver ..................................... 12, 13
Replacing batteries ....................................... 19
Reset all ....................................................... 101
Reset menu ........................................... 99, 101
Resetting the lamp operating time
................................................................ 101, 124
Resolution ................................................... 100
Rotating images ........................................... 54
RS-232C ........................................................ 13
S
Screen size ................................................... 128
Screen switching time ................................. 57
Security menu .............................................. 95
Select Drive ................................................... 53
Settings menu ............................................... 88
Sharpness ...................................................... 85
Signal menu .................................................. 86
Sleep Mode ................................................. 100
Sleep Mode Timer ..................................... 100
SMTP Server ................................................. 97
SNMP ............................................................ 73
Soft keyboard ................................................ 92
Source .......................................................... 100
Source Search ......................................... 15, 35
Speaker .......................................................... 13
Specifications ............................................. 135
Sports ............................................................. 46
sRGB .............................................................. 46
Index
146
SSID ............................................................... 94
Standby Mode ............................................ 100
Startup Screen .............................................. 89
Storage temperature .................................. 135
Subnet Mask ........................................... 94, 96
Supported Monitor Displays .................... 133
S-Video Port ................................................. 13
Sync info ..................................................... 101
Sync. ............................................................... 86
Web Control ................................................. 70
Web Control Password ............................... 93
Web Remote ................................................. 71
WEP ............................................................... 96
Whiteboard ................................................... 46
Wired LAN menu ........................................ 96
Wireless LAN menu .................................... 93
Wireless LAN Power ................................... 93
Wireless LAN system .................................. 94
Wireless LAN unit ..................................... 127
Wireless mouse function ............................ 60
WPA .............................................................. 96
T
Temp indicator .......................................... 104
Theatre .......................................................... 46
Tint ................................................................ 85
Tracking ........................................................ 86
U
USB-A port ...................................................
USB-B port ...................................................
User button ...................................................
User Pattern ..................................................
User's Logo ...................................................
User's Logo Protection ................................
14
14
88
63
61
65
V
Video Port ..................................................... 13
Video signal .......................................... 87, 101
Volume .......................................................... 88
Volume buttons ........................................... 16
W
Web Browser ................................................ 70
Z
Zoom ............................................................. 88
Zoom ring ..................................................... 12
Download PDF