Sea-doo | LRV | Operating instructions | Sea-doo LRV Operating instructions

smo2003-005a.book Page 0 Friday, November 1, 2002 8:25 AM
SAFETY WARNING
Disregarding any of the safety precautions and instructions contained in
this Operator’s Guide, the Safety Handbook, the Safety Videocassette
and on the on-product Warning Labels could cause injury, including the
possibility of death. The operator has the responsibility to inform
passenger(s) of safety precautions.
This Operator’s Guide, the Safety Handbook and Safety Videocassette
should remain with the craft at the time of resale.
Knight’s Spray-Nine† is a trademark of Korkay System Ltd
GTX† is a trademark of Castrol Ltd. Used under license
The following trademarks are the property of Bombardier Inc. or its
subsidiaries:
SEA-DOO®
BOMBARDIER-ROTAX®
BOMBARDIER LUBE®
BOMBARDIER-ROTAX Formula XP-S Synthetic Injection Oil
BOMBARDIER Formula XP-S DI Synthetic Injection Oil
BOMBARDIER-ROTAX Injection Oil
Sea-Doo Synthetic Grease
Sea-Doo LKTM
Rotax®
Printed in Canada (smo2003-005a.fm SG)
®*Trademarks of Bombardier Inc. or its subsidiaries.
©2002 Bombardier Inc. All rights reserved.
smo2003-005a.book Page 1 Friday, November 1, 2002 8:25 AM
Doin’it on your new Sea-Doo watercraft
Congratulations, you are now the proud owner of a Sea-Doo personal watercraft.
Whether you are an experienced boater or are new to the sport of boating, we ask
you to take the time to view the Safety Videocassette provided with the watercraft,
to read this Operator’s Guide, the Safety Handbook and on-product warning/caution
labels and familiarize yourself with the contents. These manuals contain pertinent
information which, if followed, will provide you with the necessary knowledge to
help you fully enjoy the pleasures of this watercraft.
We strongly recommend that all watercraft operators complete a safety boating
course. Check with your local Coast Guard or Power and Sail Squadron in your
area for course availability. More serious boaters may want to obtain Chapman
Piloting by Elbert S. Maloney, available at most book stores.
When introducing your family or friends to the sport, be sure they fully understand
the controls and operation of the watercraft and the importance of courteous,
responsible riding.
Each operator has a responsibility to ensure the safety of his/her passenger(s)
and of other water users. Please follow all safety instructions and operate your
craft with care.
We encourage you to have an Annual Safety Inspection of your watercraft. Please
contact your dealer for further details.
Finally, we urge you to visit your dealer regularly for regular and safety maintenance as well as any watercraft accessories you may require.
Have fun and... Bon Voyage.
Please keep this guide and Safety Handbook on board at all times. These
manuals along with the Safety Videocassette should remain with the watercraft at time of resale.
1
smo2003-005a.book Page 2 Friday, November 1, 2002 8:25 AM
TABLE OF CONTENTS
FOREWORD ................................................................................
5
SAFETY MEASURES...............................................................
General ....................................................................................................
Operation.................................................................................................
Maintenance............................................................................................
LIST OF DISTRIBUTORS .............................................................
6
6
6
8
9
BOMBARDIER LIMITED WARRANTY NORTH AMERICA ............. 10
BOMBARDIER LIMITED WARRANTY SOLD
AND REGISTERED IN CALIFORNIA ............................................ 13
BOMBARDIER LIMITED WARRANTY INTERNATIONAL............... 16
REGISTRATION NUMBER LOCATION ......................................... 19
LOCATION OF THE IMPORTANT LABELS ................................... 20
IDENTIFICATION NUMBERS ....................................................... 23
Hull .......................................................................................................... 23
Engine...................................................................................................... 23
CONTROLS, COMPONENTS AND INSTRUMENTS LOCATION ...... 24
CONTROLS, COMPONENTS AND INSTRUMENTS FUNCTIONS..... 26
1) Safety Lanyard (engine cut-off cord) ................................................. 26
2) Handlebar .......................................................................................... 27
3) Throttle Lever.................................................................................... 27
4) Engine Start/Stop Button .................................................................. 27
5) Shift Lever......................................................................................... 27
6) Speedometer .................................................................................... 28
7) Information Center Gauge/Buttons (if so equipped) ......................... 28
8) Glove Box.......................................................................................... 32
9) Fuel Tank Cap ................................................................................... 32
10) Oil Injection Reservoir Cap................................................................ 32
11) Front Storage Compartment Cover................................................... 32
12) Front Storage Compartment Cover Latch ......................................... 33
13) Side Storage Compartments............................................................. 33
14) Underseat Storage Compartments ................................................... 33
15) Tool Kit .............................................................................................. 33
16) Air Intake Opening ............................................................................ 33
17) Seat Strap ......................................................................................... 33
18) Seat Latch ......................................................................................... 33
19) Seat Extension Latch ........................................................................ 34
20) Rear Storage Basket (if so equipped)................................................ 34
21) Sun Deck........................................................................................... 34
22) Bow and Stern Eyelets ..................................................................... 35
23) Fender Cleats .................................................................................... 35
24) Footboard .......................................................................................... 35
2
smo2003-005a.book Page 3 Friday, November 1, 2002 8:25 AM
25) Boarding Platform .............................................................................
26) Boarding Step ...................................................................................
27) Cooling System Bleed Outlet............................................................
28) Deck Drains.......................................................................................
29) Flushing Connector ...........................................................................
30) Bilge Drain Plugs...............................................................................
31) Automatic Bilge Pump ......................................................................
32) Jet Pump Nozzle ...............................................................................
33) Reverse Gate ....................................................................................
34) Jet Pump Water Intake .....................................................................
35) Fuses ................................................................................................
36) Battery ..............................................................................................
FUEL AND LUBRICATION ...........................................................
Fueling Procedure ...................................................................................
Recommended Fuel ................................................................................
Recommended Oil ..................................................................................
Oil Injection System ................................................................................
BREAK-IN PERIOD ......................................................................
10-Hour Inspection ..................................................................................
PRE-OPERATION CHECKS ..........................................................
Hull ..........................................................................................................
Jet Pump Water Intake ...........................................................................
Bilge ........................................................................................................
Battery.....................................................................................................
Fuel Tank and Oil Reservoir ......................................................................
Engine Compartment ..............................................................................
Steering System......................................................................................
Throttle System.......................................................................................
Shifter System.........................................................................................
Storage Compartment Covers and Seat..................................................
Safety Lanyard and Engine Start/Stop Button .........................................
OPERATING INSTRUCTIONS ......................................................
Principle of Operation..............................................................................
Boarding the Watercraft ..........................................................................
Starting ....................................................................................................
Rough Water or Poor Visibility Operation................................................
Crossing Waves ......................................................................................
Stopping/Docking ....................................................................................
Beaching..................................................................................................
Shutting Off the Engine...........................................................................
POST-OPERATION CARE.............................................................
General Care............................................................................................
Additional Care for Foul Water or Salt Water ..........................................
Cooling System Flushing and Engine Internal Lubrication ......................
Anticorrosion Treatment..........................................................................
35
35
36
36
36
36
37
37
37
37
37
37
38
38
38
38
39
40
40
41
42
42
42
42
42
42
42
43
43
43
43
44
44
46
48
49
49
49
49
49
50
50
50
50
52
3
smo2003-005a.book Page 4 Friday, November 1, 2002 8:25 AM
SPECIAL PROCEDURES..............................................................
Limp Home Mode ...................................................................................
Engine Overheating .................................................................................
Jet Pump Water Intake and Impeller Cleaning ........................................
Capsized Watercraft ................................................................................
Submerged Watercraft ............................................................................
Water-Flooded Engine .............................................................................
Out of Fuel...............................................................................................
Towing the Watercraft in Water ..............................................................
Low-Charge Battery Condition ................................................................
MAINTENANCE ..........................................................................
Engine Emissions Information.................................................................
Lubrication ...............................................................................................
Periodic Inspection ..................................................................................
Periodic Inspection Chart.........................................................................
Throttle Cable Inspection.........................................................................
Fuel Injection System ..............................................................................
Fuel and Oil Filters...................................................................................
Steering Alignment..................................................................................
Vacuum Bailer Pick-Ups...........................................................................
Fuses .......................................................................................................
General Inspection and Cleaning .............................................................
TRAILERING, STORAGE AND PRE-SEASON PREPARATION.......
Trailering ..................................................................................................
Storage ....................................................................................................
Pre-Season Preparation ...........................................................................
TROUBLESHOOTING ..................................................................
53
53
53
53
54
54
55
55
55
56
57
57
58
59
60
62
62
62
62
62
63
64
65
65
65
69
71
SPECIFICATIONS........................................................................ 75
SI METRIC INFORMATION .......................................................... 77
ABBREVIATIONS USED IN THIS MANUAL ................................. 78
PRIVACY INFORMATION ............................................................ 79
CHANGE OF ADDRESS............................................................... 81
4
smo2003-005a.book Page 5 Friday, November 1, 2002 8:25 AM
FOREWORD
The Operator’s Guide and Safety Handbook have been prepared to acquaint
the owner/operator or passenger with
this personal watercraft and its various
controls, maintenance and safe riding
instructions. Each is indispensable for
the proper use of the product, and
should be kept in a waterproof bag with
the watercraft at all times.
Make sure you read and understand the
content of the Operator’s Guide and
Safety Handbook.
For any questions pertaining to the
warranty and its application, consult
the WARRANTY section in this guide,
and/or an authorized SEA-DOO dealer.
This guide uses the following safety
alert symbol in conjunction with signal
words to indicate a potential personal
injury hazard.
WARNING
Indicates a potentially hazardous
situation which, if not avoided,
could result in death or serious injury.
CAUTION
Indicates a potentially hazardous
situation which, if not avoided,
may result in minor or moderate injury. When used without the safety
alert symbol , potential hazard
exists for property damage only.
NOTE: Indicates supplementary information needed to fully complete an instruction.
Although the mere reading of such information does not eliminate the hazard, the understanding and application
of the information will promote the correct use of the watercraft.
The information and components/
system descriptions contained in this
guide are correct at the time of writing.
Bombardier Motor Corporation of
America (B.M.C.A.) however, maintains
a policy of continuous improvement of
its products without imposing upon itself any obligation to install them on
products previously manufactured.
Because of its ongoing commitment to
product quality and innovation, B.M.C.A.
reserves the right at any time to discontinue or change specifications, designs,
features, models or equipment without
incurring obligation.
The illustrations in this document show
the typical construction of the different
assemblies and may not represent the
full detail or exact shape of the parts.
However, they represent parts that
have the same or similar function.
It is understood that this guide may be
translated into another language. In
the event of any discrepancy, the English version shall prevail.
Specifications are given in the SI metric system with the SAE U.S. equivalent in parenthesis. Where precise accuracy is not required, some conversions
are rounded off for easier use.
A Shop Manual can be obtained for
complete service, maintenance and
more repair information.
5
smo2003-005a.book Page 6 Friday, November 1, 2002 8:25 AM
SAFETY MEASURES
General
Operation
To fully appreciate the pleasures,
enjoyment and excitement of boating there are some basic rules that
should be observed and followed by
any rider. Some rules may be new
to you or covered in the Sea-Doo
Safety Handbook or Safety Videocassette, others may be common
sense or obvious… irrespective, we
ask that you please take a few minutes of your time to read these safety instructions completely together
with your safety handbook and any
supplement applicable to your model before you operate your watercraft. Failure to follow this safety
information and safe boating rules
could result in injury, including the
possibility of death to you, your
passenger(s), or other water users.
Bombardier recommends not to operate a watercraft under 16 years of
age.
Become completely familiar with the
controls and operation of the watercraft before embarking on your first
trip or taking on a passenger(s). If you
have not had the opportunity to do so
with your authorized Sea-Doo dealer,
practice driving solo in a suitable area
and feel the response of each control. Be fully familiar with all controls
before applying throttle above idle
speed. As its operator, you control
and are responsible for the watercraft’s safe operation.
Always carry the regulatory required
safety items on board. Check the local regulations or consult your authorized Sea-Doo dealer.
Make sure that all users of the watercraft read and understand all onproduct warnings.
Always perform the pre-operation
checks as specified in this guide.
Operator and passenger(s) should at
all times wear a coast guard approved
personal flotation device (PFD) that is
suitable for personal watercraft.
Operator and passenger(s) should
wear protective clothing. Severe internal injuries can occur if water is
forced into body cavities of males or
females as a result of falling into water or being near jet thrust nozzle. Wet
suit bottom (or thick, tightly woven,
snug fitting clothing that provides
equivalent protection. Thin bike shorts
for example would not be appropriate),
footwear, gloves and goggles/glasses
are recommended.
Always keep in mind that as the
throttle lever is released to idle position, less directional control is available. To turn the watercraft, both
steering and throttle are necessary.
Like any other craft, this watercraft
has no brake. Stopping distance will
vary depending on initial speed, load,
wind, and water conditions. Practice
stopping and docking in a safe, traffic
free area to have an idea of how long
it will take to stop the watercraft under varying conditions. Do not release throttle when trying to steer
away from objects. You need throttle
to steer. Do not use the watercraft’s
reverse, if so equipped, to stop.
Ensure that all passengers know
how to swim and how to reboard
the watercraft from the water.
The operator and passenger(s) should
be properly seated and wearing an
approved PFD before starting or
moving the watercraft, and at all
times when watercraft is in motion.
6
smo2003-005a.book Page 7 Friday, November 1, 2002 8:25 AM
Do not start or operate the watercraft if someone is seated on the sun
deck or swim platform, or is nearby
in the water. The watercraft’s jet
thrust can cause injury. Always accelerate slowly.
To prevent accidental starting or unauthorized use, always detach the
safety lanyard from the watercraft especially when swimmers are boarding or nearby, or during removal of
any weeds or debris from the intake
grate.
Never turn handlebar while someone is nearby rear of watercraft. Keep
away from steering moving parts
(nozzle, rudders, linkage, etc.)
Keep away from intake grate while
engine is on. Items such as long hair,
loose clothing, or PFD straps can become entangled in moving parts resulting in severe injury or drowning.
Ride within your limits and avoid aggressive maneuvers to reduce the
risk of loss of control, ejection and
collision.
Riding with a passenger(s) or pulling
other crafts, tubes, skies or wakeboards makes the watercraft handle
differently and requires greater skill.
Do not overload the watercraft or
take on more passengers than designated for the particular watercraft.
Overloading can affect maneuverability, stability and performance.
Avoid adding on accessories, or
equipment which may alter the
configuration, balance or control of
the watercraft. The watercraft maybe fitted with tow eyelets which can
be used to attach a ski rope. However, do not use these eyelets or the
watercraft’s cleats to tow a parasail.
Severe injury or watercraft damage
may occur.
In shallow water, proceed with caution and at very low speeds. Grounding or abrupt stops may result in injury. Debris may also be picked up
and be thrown rearward by the jet
pump onto people or property.
Respect no wake zones, the rights
of other water users and the environment. As the “skipper” and owner
of a watercraft you are responsible
for damage to other crafts caused by
the wake of your watercraft. Allow
no one to throw refuse overboard.
Remember that a watercraft is not
designed for night time operation.
Remember, gasoline fumes are inflammable and explosive. Always
adhere to the fueling procedure
contained in this guide and those
given to you by the marina. Always
verify fuel level before use and during the ride. Apply the principle of
1/3 fuel to destination, 1/3 back and
1/3 reserve fuel supply. Do not carry
spare fuel or inflammable liquids in
any of the storage or engine compartments.
Combustion engine needs air to operate; consequently this watercraft
can not be totally watertight. Any
maneuvers such as figure eights
etc., that cause the upper deck to be
under water may cause severe engine problems due to water ingestion.
Refer to SPECIAL PROCEDURES and
Limited Warranty contained in this
guide.
Due to the close proximity of other
racers, it is recommended that an
approved personal watercraft helmet be used during racing events.
Read and follow all instructions and
warnings provided with the helmet.
Never ride after consuming drugs or
alcohol or if you feel tired or ill. Operate your watercraft prudently and
have fun.
Don’t forget that all persons must
assist other boaters in an emergency.
7
smo2003-005a.book Page 8 Friday, November 1, 2002 8:25 AM
Maintenance
Only perform servicing procedures
which are detailed in this guide. Further assistance or information can
be obtained from your authorized
Sea-Doo dealer. In many instances
proper tools and training is required
for certain servicing or repair procedures.
Maintain the watercraft and equipment in top condition at all times. Adhere to the prescribed maintenance
schedules. An annual inspection of
the watercraft is always a good recommendation that should be followed.
Always use spark plug cable grounding device when removing spark
plugs. Never check for engine ignition spark from an open cable
and/or spark plug in the engine compartment as spark may cause fuel
vapor to ignite.
The bilge should be kept clean of oil,
water or other foreign materials.
Do not attempt to lift the watercraft
without special equipment and training.
The engine and the corresponding
components identified in this guide
should not be utilized on product(s)
other than for those they were designed. Maintenance procedures and
specified tightening torque should be
strictly adhered to. Never attempt repairs unless the appropriate tools are
available. These watercrafts are designed with parts dimensioned in
both the metric and the imperial
systems. When replacing fasteners,
make sure to use only those recommended by Bombardier. If required,
contact your authorized Sea-Doo
dealer for further servicing information.
8
smo2003-005a.book Page 9 Friday, November 1, 2002 8:25 AM
LIST OF DISTRIBUTORS
NORTH AMERICA
USA
(Except Puerto Rico)
CANADA
BOMBARDIER MOTOR CORPORATION
OF AMERICA
7575 Bombardier Court
WAUSAU, WI. 54401
Phone: (715) 848-4957
Fax: (715) 847-6879
www.bombardier.com
BOMBARDIER INC.
RECREATIONAL PRODUCTS
75 J. A. BOMBARDIER ST.
SHERBROOKE, QC
J1L 1W3
Phone: (819) 566-3366
Fax: (819) 566-3062
www.bombardier.com
If your Sea-Doo watercraft requires warranty service, you should take it to any
authorized Sea-Doo dealer. Be sure to bring your warranty registration card or
other valid proof of the original date of purchase. If a question or problem arises
regarding warranty, first contact the service manager or owner of the Sea-Doo
dealership.
To find the nearest authorized Sea-Doo dealer, dial: 1-800-882-2900.
NOTE: If outside Canada or USA, consult your local authorized Sea-Doo distributor.
9
smo2003-005a.book Page 10 Friday, November 1, 2002 8:25 AM
BOMBARDIER LIMITED WARRANTY NORTH
AMERICA: SEA-DOO® WATERCRAFT
1. SCOPE OF THE LIMITED WARRANTY
In Canada, BOMBARDIER INC. (hereinafter “BOMBARDIER”), and in the USA, Bombardier
on behalf of BOMBARDIER MOTOR CORPORATION OF AMERICA (BMCA) warrants its
SEA-DOO watercraft from defects in material or workmanship for the period described
below.
All genuine BOMBARDIER parts and accessories, installed by an authorized BOMBARDIER
dealer (as hereinafter defined) at the time of delivery of the SEA-DOO watercraft, carry the
same warranty as that of the watercraft.
Use of the product for racing or any other competitive activity, at any point, even by a previous
owner, will render this warranty null and void.
2. WARRANTY COVERAGE PERIOD
This warranty will be in effect FROM THE DATE OF DELIVERY TO THE FIRST RETAIL CONSUMER or the date the product is first put into use, whichever occurs first and for a period of:
a) For private use owners:
• TWELVE (12) CONSECUTIVE MONTHS.
In the USA: SEA-DOO RX™ DI, SEA-DOO GTX† DI and SEA-DOO LRV™ DI
• TWELVE (12) CONSECUTIVE MONTHS for the emission related components providing
input to emission control. (e.g. sensors).
b) For commercial use owners:
• FOUR (4) CONSECUTIVE MONTHS.
In the USA: SEA-DOO RX™ DI, SEA-DOO GTX† DI and SEA-DOO LRV™ DI
• TWELVE (12) CONSECUTIVE MONTHS for the emission related components providing
input to emission control. (e.g. sensors).
The repair or replacement of parts or the performance of service under this warranty does
not extend the life of this warranty beyond its original expiration date.
CALIFORNIA RESIDENTS purchasing a SEA-DOO RX™ DI, a SEA-DOO GTX† DI, or a SEA-DOO
LRV™ DI personal watercraft in California please also refer to the California Emissions Control
Limited Warranty Statement.
3. CONDITIONS TO HAVE WARRANTY COVERAGE
This warranty coverage is available only on SEA-DOO watercraft purchased as new and
unused by its first owner from a BOMBARDIER dealer authorized to distribute SEA-DOO
products in the country in which the sale occurred (hereinafter “BOMBARDIER dealer”),
and then only after the BOMBARDIER specified pre-delivery inspection process is completed and documented. Warranty coverage only becomes available upon proper registration of the product by an authorized BOMBARDIER dealer. Such limitations are necessary
in order to allow BOMBARDIER to preserve both the safety of its products, and also that
of its consumers and the public.
Routine maintenance outlined in the Operator’s Guide must be timely performed in order
to maintain warranty coverage. BOMBARDIER reserves the right to make warranty coverage contingent upon proof of proper maintenance.
4. WHAT TO DO TO OBTAIN WARRANTY COVERAGE
The customer must notify an authorized servicing BOMBARDIER dealer within two (2)
days of the appearance of a defect, and provide it with reasonable access to the product
and reasonable opportunity to repair it. The customer must also present to the authorized
BOMBARDIER dealer, proof of purchase of the product and must sign the repair/work
order prior to starting the repair in order to validate the warranty repair. All parts replaced
under this limited warranty become the property of BOMBARDIER.
10
smo2003-005a.book Page 11 Friday, November 1, 2002 8:25 AM
5. WHAT BOMBARDIER WILL DO
BOMBARDIER’s obligations under this warranty are limited to, at its sole discretion, repairing parts found defective under normal use, maintenance and service, or replacing such
parts with new genuine BOMBARDIER parts without charge for parts and labor, at any
authorized BOMBARDIER dealer.
BOMBARDIER reserves the right to improve or modify products from time to time without
assuming any obligation to modify products previously manufactured.
6.
•
•
•
•
•
•
•
•
•
•
EXCLUSIONS - ARE NOT WARRANTED
Normal wear and tear;
Routine maintenance items, tune ups, adjustments;
Damage caused by failure to provide proper maintenance and/or storage, as described
in the Operator’s Guide;
Damage resulting from removal of parts, improper repairs, service, maintenance, modifications or use of parts not manufactured or approved by BOMBARDIER or resulting from
repairs done by a person that is not an authorized servicing BOMBARDIER SEA-DOO
dealer;
Damage caused by abuse, abnormal use, neglect, or operation of the product in a manner inconsistent with the recommended operation described in the Operator’s Guide;
Damage resulting from accident, submersion, fire, theft, vandalism or any act of God;
Operation with fuels, oils or lubricants which are not suitable for use with the product
(see the Operator’s Guide);
Water damages caused by water ingestion;
Damages related to gel coat finish including but not limited to cosmetic gel coat finish,
blisters or fiberglass delamination caused by blisters, crazing, spyder or hairline cracks;
and
Incidental or consequential damages, or damages of any kind including without limitation towing, storage, telephone, rental, taxi, inconvenience, insurance coverage, loan
payments, loss of time, loss of income.
7. LIMITATIONS OF LIABILITY
THIS WARRANTY IS EXPRESSLY GIVEN AND ACCEPTED IN LIEU OF ANY AND ALL
OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. TO THE EXTENT THAT THEY CANNOT BE DISCLAIMED, THE IMPLIED
WARRANTIES ARE LIMITED IN DURATION TO THE LIFE OF THE EXPRESS WARRANTY. INCIDENTAL AND CONSEQUENTIAL DAMAGES ARE EXCLUDED FROM COVERAGE UNDER THIS WARRANTY. SOME STATES/PROVINCES DO NOT ALLOW FOR
THE DISCLAIMERS, LIMITATIONS AND EXCLUSIONS IDENTIFIED ABOVE, AS A RESULT, THEY MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC
RIGHTS, AND YOU MAY ALSO HAVE OTHER LEGAL RIGHTS WHICH MAY VARY
FROM STATE TO STATE, OR PROVINCE TO PROVINCE.
Neither the distributor, any BOMBARDIER dealer nor any other person has been authorized
to make any affirmation, representation or warranty regarding the product, other than
those contained in this limited warranty, and if made, shall not be enforceable against
BOMBARDIER.
BOMBARDIER reserves the right to modify this warranty at any time, being understood
that such modification will not alter the warranty conditions applicable to the products sold
while this warranty is in effect.
11
smo2003-005a.book Page 12 Friday, November 1, 2002 8:25 AM
8. TRANSFER
If the ownership of a product is transferred during the warranty coverage period, this warranty shall also be transferred and be valid for the remaining coverage period provided that
BOMBARDIER is notified of such transfer of ownership in the following way:
a) The former owner contacts BOMBARDIER (at the phone number provided below) or
an authorized BOMBARDIER dealer and gives the coordinates of the new owner; or
b) BOMBARDIER or an authorized BOMBARDIER dealer receives a proof that the former
owner agreed to the transfer of ownership, in addition to the coordinates of the new
owner.
9. CONSUMER ASSISTANCE
a) In the event of a controversy or a dispute in connection with this BOMBARDIER LIMITED
WARRANTY, BOMBARDIER suggests that you try to resolve the issue at the dealership
level. We recommend discussing the issue with the authorized dealer’s service manager
or owner.
b) If the issue has not yet been resolved, please submit your complaint in writing or call
the appropriate number below:
In Canada:
In USA:
BOMBARDIER INC.
RECREATIONAL PRODUCTS
CUSTOMER ASSISTANCE CENTER
VALCOURT QC J0E 2L0
Tel: (819) 566-3366
©
BOMBARDIER MOTOR
CORPORATION OF AMERICA
CUSTOMER ASSISTANCE CENTER
7575 BOMBARDIER COURT
WAUSAU WI 54401
Tel: (715) 848-4957
2002 Bombardier Inc. All rights reserved
™ Registered trademarks of Bombardier Inc. or its subsidiaries.
† Trademark of Castrol Ltd, used under license.
®
12
smo2003-005a.book Page 13 Friday, November 1, 2002 8:25 AM
ONLY FOR 2002 SEA-DOO® RX™ DI,
SEA-DOO GTX† DI AND SEA-DOO LRV™ DI
SOLD AND REGISTERED IN CALIFORNIA
CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT
Your SEA-DOO watercraft has a special environmental label required by the California Air
Resources Board (CARB). The label has 1, 2, or 3 stars. A hangtag, provided with your
personal watercraft, describes the meaning of the star rating system.
The Star Label Means Cleaner Marine Engines
F00L2ZQ
The Symbol for Cleaner Marine Engines:
Cleaner Air and Water
For a healthier lifestyle and environment.
Better Fuel Economy
Burns up to 30 - 40 percent less gas and oil than conventional carbureted twostroke engines, saving money and resources.
Longer Emission Warranty
Protects consumer for worry free operation.
One Star - Low-Emission
The one-star label identifies engines that meet the Air Resources Board’s 2001 exhaust
emission standards. Engines meeting these standards have 75% lower emissions than
conventional carbureted two-stroke engines. These engines are equivalent to the U.S.
EPA’s 2006 standards for marine engines.
Two Stars - Very Low Emission
The two-star label identifies engines that meet the Air Resources Board’s 2004 exhaust
emission standards. Engines meeting these standards have 20% lower emissions than
One Star - Low - Emission engines.
Three Stars - Ultra Low Emission
The three-star label identifies engines that meet the Air Resources Board’s 2008 exhaust
emission standards. Engines meeting these standards have 65% lower emissions than
One Star - Low Emission engines.
For more information:
Cleaner Watercraft – Get the Facts
1 800 END-SMOG
www.arb.ca.gov
13
smo2003-005a.book Page 14 Friday, November 1, 2002 8:25 AM
YOUR EMISSION CONTROL WARRANTY RIGHTS AND OBLIGATION
The California Air Resources Board and BOMBARDIER on behalf of BOMBARDIER MOTOR
CORPORATION OF AMERICA (BMCA) are pleased to explain the emission control system
warranty on your 2002 SEA-DOO RX™ DI, SEA-DOO GTX† DI and SEA-DOO LRV™ DI
personal watercraft engine. In California, new personal watercraft engines must be designed, built and equipped to meet the State’s stringent anti-smog standards. BOMBARDIER
must warrant the emission control system on your personal watercraft engine for the periods
of time listed below provided there has been no abuse, neglect or improper maintenance of
your personal watercraft engine.
Your emission control system may include parts such as the fuel injection system or the
ignition system. Also included may be hoses, connectors and other emission-related assemblies.
Where a warrantable condition exists, BOMBARDIER will repair your personal watercraft
engine at no cost to you including diagnosis, parts and labor provided that such work is
performed by an authorized BOMBARDIER dealer.
Manufacturer’s Limited Warranty Coverage
This emission limited warranty covers model year 2002 SEA-DOO RX™ DI, SEA-DOO
GTX† DI and SEA-DOO LRV™ DI personal watercraft engine certified and produced by
BOMBARDIER for sale in California, that are originally sold in California to a California
resident. The BOMBARDIER North America Limited warranty conditions for Sea-Doo
watercraft are still applicable to these models with the necessary modifications.
Select emission control parts of your 2002 SEA-DOO RX™ DI, SEA-DOO GTX† DI and SEA-DOO
LRV™ DI personal watercraft engine are warranted from the date of delivery to the first retail
consumer for a period of 4 years, or for 250 hours of use, whichever occurs first. However,
warranty coverage based on the hourly period is only permitted for personal watercraft equipped
with the appropriate hour meters or their equivalent. If any emission-related part on your engine
is defective under warranty, the part will be repaired or replaced by BOMBARDIER.
Parts covered are:
Air lines
Fuel rail
Rave valve
Reed valve
Tuned pipe
High-tension ignition wires
Electrical harness
Throttle bodies
Exhaust hoses
Fuel lines
Water regulator
Air compressor
Cylinder head
Detonation/ knock sensor
14
Coolant temperature sensor
Throttle position sensors
Ignition coil
Manifold temperature sensor
Manifold air pressure sensor
Crankshaft position sensor
Air pressure regulator
Fuel pressure regulator
Fuel injectors
Electronic control module
Exhaust manifold
Fuel pump
Air injector
All emission component related gaskets;
head, base and exhaust
smo2003-005a.book Page 15 Friday, November 1, 2002 8:25 AM
The emission warranty covers damage to other engine components that is caused by the
failure of a warranted part.
The Bombardier Operator’s Guide provided contains written instructions for the proper
maintenance and use of your personal watercraft. All emission warranty parts are warranted by Bombardier for the entire warranty period of the watercraft, unless the part is scheduled for replacement as required maintenance in the Operator’s Guide.
Emission warranty parts that are scheduled for replacement, as required maintenance, are
warranted by Bombardier for the period of time before the first scheduled replacement
date for that part. Emission warranty parts that are scheduled for regular inspection, but
not regular replacement, are warranted by Bombardier for the entire warranty period of
the watercraft. Any emission warranty part repaired or replaced under the terms of this
warranty statement is warranted by BOMBARDIER for the remainder of the warranty period of the original part. All parts replaced under this limited warranty become the property
of BOMBARDIER.
Maintenance receipts and records should be transferred to each subsequent owner of the
watercraft.
Owner’s Warranty Responsibilities
As the personal watercraft engine owner, you are responsible for the performance of the required maintenance listed in your Operator’s Guide. BOMBARDIER recommends that you retain all receipts covering maintenance on your personal watercraft engine, but BOMBARDIER
cannot deny warranty solely for the lack of receipts or your failure to ensure the performance
of all scheduled maintenance.
As the personal watercraft engine owner, you should however be aware that BOMBARDIER
may deny you warranty coverage if your personal watercraft engine or a part has failed due
to abuse, neglect, improper maintenance or unapproved modifications.
You are responsible for presenting your personal watercraft engine to an authorized
BOMBARDIER dealer as soon as a problem exists. The warranty repairs will be completed in a reasonable amount of time, not to exceed 30 days.
If you have any questions regarding your warranty rights and responsibilities or for the
name and location of the nearest authorized BOMBARDIER dealer you should contact the
Customer Assistance Center at 1-715-848-4957.
©
2002 Bombardier Inc. All rights reserved
™ Registered trademarks of Bombardier Inc. or its subsidiaries.
† Trademark of Castrol Ltd, used under license.
®
15
smo2003-005a.book Page 16 Friday, November 1, 2002 8:25 AM
BOMBARDIER LIMITED WARRANTY
INTERNATIONAL: SEA-DOO® WATERCRAFT
1. SCOPE OF THE LIMITED WARRANTY
BOMBARDIER INC. (hereinafter “BOMBARDIER”) warrants its SEA-DOO personal watercraft from defects in material or workmanship for the period described below.
All genuine BOMBARDIER parts and accessories, installed by an authorized BOMBARDIER
distributor/dealer (as hereinafter defined) at the time of delivery of the SEA-DOO personal
watercraft, carry the same warranty as that of the personal watercraft.
Use of the product for racing or any other competitive activity, at any point, even by a prior
owner will render this warranty null and void.
2. WARRANTY COVERAGE PERIOD
This warranty will be in effect FROM THE DATE OF DELIVERY TO THE FIRST RETAIL
CONSUMER or the date the product is first put into use, whichever occurs first and for a
period of:
a) TWELVE (12) CONSECUTIVE MONTHS, for private use owners.
b) FOUR (4) CONSECUTIVE MONTHS, for commercial use owners.
The repair or replacement of parts or the performance of service under this warranty does
not extend the life of this warranty beyond its original expiration date.
3. CONDITIONS TO HAVE WARRANTY COVERAGE
This warranty coverage is available only on SEA-DOO personal watercraft purchased as new
and unused by its first owner from a BOMBARDIER distributor/dealer authorized to distribute
SEA-DOO products in the country in which the sale occurred (hereinafter “BOMBARDIER
distributor/dealer”), and then only after the BOMBARDIER specified predelivery inspection
process is completed and documented. Warranty coverage only becomes available upon
proper registration of the product by a BOMBARDIER dealer. Such limitations are necessary
in order to allow BOMBARDIER to preserve both the safety of its products, and also that of
its consumers and the public.
Routine maintenance outlined in the Operator’s Guide must be timely performed in order
to maintain warranty coverage. BOMBARDIER reserves the right to make warranty coverage contingent upon proof of proper maintenance.
4. WHAT TO DO TO OBTAIN WARRANTY COVERAGE
The customer must notify a servicing BOMBARDIER distributor/dealer within two (2) days
of the appearance of a defect, and provide it with reasonable access to the product and
reasonable opportunity to repair it. The customer must also present to the BOMBARDIER
distributor/dealer, proof of purchase of the product and must sign the repair/work order
prior to the start of the repair in order to validate the warranty repair. All parts replaced
under this limited warranty become the property of BOMBARDIER.
5. WHAT BOMBARDIER WILL DO
BOMBARDIER’s obligations under this warranty are limited to, at its sole discretion, repairing parts found defective under normal use, maintenance and service, or replacing such
parts with new genuine BOMBARDIER parts without charge for parts and labor, at any
authorized BOMBARDIER distributor/dealer.
BOMBARDIER reserves the right to improve or modify products from time to time without
assuming any obligation to modify products previously manufactured.
16
smo2003-005a.book Page 17 Friday, November 1, 2002 8:25 AM
6.
•
•
•
•
•
•
•
•
•
•
EXCLUSIONS - ARE NOT WARRANTED
Normal wear and tear;
Routine maintenance items, tune ups, adjustments;
Damage caused by failure to provide proper maintenance and/or storage, as described
in the Operator’s Guide;
Damage resulting from removal of parts, improper repairs, service, maintenance, modifications or use of parts not manufactured or approved by BOMBARDIER or resulting
from repairs done by a person that is not an authorized servicing BOMBARDIER distributor/dealer;
Damage caused by abuse, abnormal use, neglect or operation of the product in a manner inconsistent with the recommended operation described in the Operator’s Guide;
Damage resulting from accident, submersion, fire, theft, vandalism or any act of God;
Operation with fuels, oils or lubricants which are not suitable for use with the product
(see the Operator’s Guide);
Water ingestion;
Damages related to gel coat finish including but not limited to cosmetic gel coat finish,
blisters or fiberglass delamination caused by blisters, crazing, spyder or hairline cracks;
and
Incidental or consequential damages, or damages of any kind including without limitation towing, storage, telephone, rental, taxi, inconvenience, insurance coverage, loan
payments, loss of time, loss of income.
7. LIMITATIONS OF LIABILITY
THIS WARRANTY IS EXPRESSLY GIVEN AND ACCEPTED IN LIEU OF ANY AND ALL
OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. TO THE EXTENT THAT THEY CANNOT BE DISCLAIMED, THE IMPLIED
WARRANTIES ARE LIMITED IN DURATION TO THE LIFE OF THE EXPRESS WARRANTY. INCIDENTAL AND CONSEQUENTIAL DAMAGES ARE EXCLUDED FROM COVERAGE UNDER THIS WARRANTY. SOME COUNTRIES DO NOT ALLOW FOR THE DISCLAIMERS, LIMITATIONS AND EXCLUSIONS IDENTIFIED ABOVE, AS A RESULT,
THEY MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC RIGHTS,
AND YOU MAY ALSO HAVE OTHER LEGAL RIGHTS WHICH MAY VARY FROM
COUNTRY TO COUNTRY.
Neither the BOMBARDIER distributor nor any other person has been authorized to make
any affirmation, representation or warranty regarding the product, other than those contained in this limited warranty, and if made, shall not be enforceable against BOMBARDIER.
BOMBARDIER reserves the right to modify this warranty at any time, being understood
that such modification will not alter the warranty conditions applicable to the products sold
while this warranty is in effect.
8. TRANSFER
If the ownership of a product is transferred during the warranty coverage period, this warranty shall also be transferred and be valid for the remaining coverage period provided that
BOMBARDIER is notified of such transfer of ownership in the following way:
a) The former owner contacts BOMBARDIER or an authorized BOMBARDIER distributor/
dealer and gives the coordinates of the new owner; or
b) BOMBARDIER or an authorized BOMBARDIER distributor/dealer receives a proof that
the former owner agreed to the transfer of ownership, in addition to the coordinates of
the new owner.
17
smo2003-005a.book Page 18 Friday, November 1, 2002 8:25 AM
9. CONSUMER ASSISTANCE
a) In the event of a controversy or a dispute in connection with this BOMBARDIER LIMITED
WARRANTY, BOMBARDIER suggests that you try to resolve the issue at the distributorship/
dealership level. We recommend discussing the issue with the authorized dealer’s service
manager or owner.
b) If further assistance is required, the distributor’s service department should be contacted in order to resolve the matter.
©
®
2002 Bombardier Inc. All rights reserved
Registered trademark of Bombardier Inc. or its subsidiaries.
18
smo2003-005a.book Page 19 Friday, November 1, 2002 8:25 AM
REGISTRATION NUMBER LOCATION
All personal watercraft are required by federal law to be registered and legally
numbered.
Due to space availability for proper display of registration number, refer to following illustration for location. The registration number should appear on each side
of the watercraft. On applicable models, install registration number to the left of
the star label.
F11L01L
1
1. Registration number location
NOTE: The registration number must be above the water line. Ensure also that
the numbers are of the correct size and color. Check with local applicable regulations.
19
smo2003-005a.book Page 20 Friday, November 1, 2002 8:25 AM
LOCATION OF THE IMPORTANT LABELS
The following labels are on your watercraft. If missing or damaged, they can be
replaced free of charge. See an authorized Sea-Doo dealer.
Please read the following labels carefully before operating this watercraft.
8, 10
13
6
F11L0GM
TYPICAL
20
3
2
1
11
5, 9
12
11
4
7
smo2003-005b.fm Page 21 Monday, November 11, 2002 10:28 AM
Label 1
F12L0FL
Label 2
Label 4
F12L0IY
Label 3
"THIS BOAT IS NOT REQUIRED TO COMPLY WITH THE
FOLLOWING U.S. COAST GUARD SAFETY STANDARDS
IN EFFECT ON THE DATE OF CERTIFICATION:
Fuel System
Display of Capacity
Information
F11L0KY
TYPICAL
Safe Loading
Flotation
Powered Ventilation
Label 5
• WARNING
AS AUTHORIZED BY U.S. COAST GUARD GRANT OF
EXEMPTION (CGB 88-001)."
Bombardier Corp.
7575 Bombardier Court, Wausau, WI 54401
Made in USA/ Fabriqué aux États-Unis Bombardier Inc. Rd./ Enr.,1988
F02L2D1
DO NOT BOOST BATTERY
WHILE INSTALLED.
F00L050
21
smo2003-005b.fm Page 22 Monday, November 11, 2002 10:28 AM
Label 6
Label 10
F00A18Y
SOME MODELS
F06L0DZ
Label 11
Label 7
F11L0EY
Label 12
F07L24Y
SOME MODELS
F11L0FY
Label 8
Label 13
F00L2MY
Label 9
F00L2YY
SOME MODELS
F00L2FY
SOME MODELS
22
smo2003-005a.book Page 23 Friday, November 1, 2002 8:25 AM
IDENTIFICATION NUMBERS
The main components of the watercraft (engine and hull) are identified by
different serial numbers. It may sometimes become necessary to locate
these numbers for warranty purposes
or to trace the watercraft in the event
of theft.
Engine
The Engine Identification Number (E.I.N.)
is located on the upper crankcase on
MAGNETO side.
Hull
The Hull Identification Number (H.I.N.)
is located on footboard at the rear of
watercraft.
F06D15Y
1
1. Engine Identification Number (E.I.N.)
1
F11L05Y
1. Hull Identification Number
It is composed of 12 digits:
CEC 1 2 3 4 5 L 4 9 5
Model year
Serial
number*
Year of production
Month of production
F00A0YY
*A letter may also be used as a digit.
23
smo2003-005a.book Page 24 Friday, November 1, 2002 8:25 AM
CONTROLS, COMPONENTS AND
INSTRUMENTS LOCATION
NOTE: Some components do not apply or are optional on some models.
9
5
2
1
24
18
21
19
22
25
27
22
36
14-20
16
28
26-29-30
32-33
13 34 31
17
35
14
7
12
6
13
15
10
11
23
4
3
8
F11L0IL
24
smo2003-005a.book Page 25 Friday, November 1, 2002 8:25 AM
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
Safety Lanyard
Handlebar
Throttle Lever
Engine Start/Stop Button
Shift Lever
Speedometer
Information Center Gauge/Buttons
Glove Box
Fuel Tank Cap
Oil Injection Reservoir Cap
Front Storage Compartment Cover
Front Storage Compartment
Cover Latch
Side Storage Compartments
Underseat Storage Compartments
Tool Kit
Air Intake Opening
Seat Strap
Seat Latch
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
33.
34.
35.
36.
Seat Extension Latch
Rear Storage Basket
Sun Deck
Bow and Stern Eyelets
Fender Cleats
Footboard
Boarding Platform
Boarding Step
Cooling System Bleed Outlet
Deck Drains
Flushing Connector
Bilge Drain Plugs
Automatic Bilge Pump
Jet Pump Nozzle
Reverse Gate
Jet Pump Water Intake
Fuses
Battery
25
smo2003-005a.book Page 26 Friday, November 1, 2002 8:25 AM
CONTROLS, COMPONENTS AND
INSTRUMENTS FUNCTIONS
1) Safety Lanyard
(engine cut-off cord)
The safety lanyard cap should be securely snapped onto its post to be fully
operational.
Pulling the safety lanyard cap from its
post stops the engine operation. Attach the safety lanyard to the operator’s Personal Flotation Device (PFD)
and snap the cap to the post to be able
to start the engine.
Two short beeps indicates the system
is ready to allow engine starting. Otherwise, refer to the TROUBLESHOOTING section for the coded signals chart.
F00L07Y
1
2
TYPICAL
1. Safety lanyard cap on the post
2. Safety lanyard secured on operator’s PFD
WARNING
Should the safety lanyard cap become loose or fails to remain on
its post, replace it immediately.
Digitally Encoded Security
System (DESS)
The safety lanyard cap specifically contains an electronic circuit that gives it
a unique electronic serial number. This
is the equivalent of a conventional key.
This safety lanyard cannot be used on
another watercraft and conversely, the
one from another watercraft cannot be
used on your watercraft.
However, the DESS brings a great flexibility. You can buy an additional safety
lanyard and have it programmed for
your watercraft.
The DI Model also offers a special
safety lanyard — the SEA-DOO LKTM
(SEA-DOO Learning KeyTM) — which
electronically limits the speed of the
watercraft to approximately 55 km/h
(35 MPH) therefore enabling first time
users and less experienced operators
to learn how to operate the watercraft
while gaining the necessary confidence
and control.
WARNING
Should the engine be stopped, watercraft directional control is lost.
Always disconnect safety lanyard
when watercraft is not in operation in order to prevent accidental
engine starting or to avoid unauthorized use by children or others
or theft.
F00L2SY
26
smo2003-005a.book Page 27 Friday, November 1, 2002 8:25 AM
To have an additional safety lanyard,
refer to an authorized SEA-DOO dealer.
If the engine is stopped with the start/
stop button while the safety lanyard remains on the post, it can be restarted
within approximately 10 minutes by
pressing the engine start/stop button.
After this delay, it is necessary to apply
a slight pressure or to remove and reinstall the safety lanyard on the post to
allow engine starting.
To stop engine, fully release throttle lever
then depress the start/stop button and
disconnect safety lanyard from the post.
WARNING
Directional control is reduced when
the throttle is released and lost
when engine is off.
1
WARNING
While engine can be stopped using the engine start/stop button,
good habits recommend that the
safety lanyard also be disconnected when stopping.
2) Handlebar
The handlebar controls the direction of
the watercraft. Turning the handlebar
to the right steers the watercraft to the
right and inversely.
WARNING
Check handlebar and corresponding steering nozzle operation before starting.
3) Throttle Lever
When the throttle lever is squeezed,
the watercraft accelerates. When fully
released, engine automatically slows
down to idle speed and watercraft is
gradually stopped by water drag.
4) Engine Start/Stop
Button
To start engine, depress and hold the
start/stop button. Release immediately after engine is started.
F01L63Y
1. Engine start/stop button
With the Digitally Encoded Security
System, leaving the safety lanyard for
more than 10 minutes after stopping
the engine will require a slight pressure or the removal and reinstallation
of the safety lanyard on the post to allow engine starting.
5) Shift Lever
A push-pull lever:
– forward
– neutral
– reverse.
WARNING
Shift lever should only be used
when the engine is idling and craft
is completely stopped. Do not use
as a grab handle.
WARNING
Only use reverse at slow speed
and for the shortest time possible.
Always ensure the path behind is
clear of objects and persons including children playing in shallow
water.
CAUTION: Never rev the engine at
high RPM in reverse.
27
smo2003-005a.book Page 28 Friday, November 1, 2002 8:25 AM
From the forward position, pull the lever to reverse. Push back to go to forward. Always set in forward when finished. To find the neutral, set in
reverse then push back until the watercraft stops moving backwards.
6) Speedometer
Analog speedometer indicates the
speed of watercraft in miles per hour
(MPH) and kilometers per hour (km/h).
The speed sensor mounted on the ride
plate sends the signal to the speedometer and information center.
7) Information Center
Gauge/Buttons
(if so equipped)
F17L0AY
TYPICAL — FORWARD POSITION
NOTE: With the safety lanyard disconnected, information center can be activated for approximately 33 seconds
by depressing the engine start/stop
button. This is convenient to see the
fuel level or view some other functions
when the safety lanyard is not at hand.
This is a LCD multifunction gauge. Different displays and functions can be
activated using 2 buttons — MODE
and SET — following specific sequences as described below.
F17L0BY
TYPICAL — NEUTRAL POSITION
F00L2BY
1
2
1. To change display mode
2. To set or reset a function
Resetting a Function
To reset a function (such as the chronometer, distance, etc.) press and hold
the SET button for 2 seconds while in
the appropriate mode.
F17L0CY
TYPICAL — REVERSE POSITION
28
smo2003-005a.book Page 29 Friday, November 1, 2002 8:25 AM
The information center includes the following display areas.
2
1
5
When you are satisfied with your choice,
stop pressing the button.
Clock: Indicates the actual time in hours
and minutes (hh:mm).
Clock/Compass (if so equipped): Displays the cardinal points to indicate the
orientation of the watercraft.
WARNING
Use the compass as a guide only.
Not to be used for navigation purposes.
F00L2CY
1.
2.
3.
4.
5.
3
4
General display
Message/units display
Warning light
Fuel level display
VTS position indicator (if so equipped)
General Display
The default display is the clock (or
clock/compass if so equipped) unless
another mode has been selected. See
Display Priorities below.
Repeatedly pressing the MODE button
scrolls the following displays: Tachometer, speedometer, average speed, trip
meter, hourmeter, water temperature,
exterior temperature (if so equipped)
and chronometer.
F00L2BZ
Tachometer: Indicates the revolutions
per minute (RPM) of the engine.
Speedometer: Indicates the speed of
watercraft in kilometers per hour (KPH)
or miles per hour (MPH).
Average Speed: The information center approximately calculates and displays the average speed (AV KPH or
AV MPH) of the watercraft since the
last engine start.
Trip Meter: The information center approximately calculates the distance
based on the operation time and the watercraft speed and displays the result in
kilometers (KM) or miles (MILES).
Hourmeter: Displays the time in hours
of the watercraft usage.
Water Temperature: Displays the water temperature (L TEMP) in degrees
Celsius (°C) or Farenheit (°F).
Exterior Temperature (if so equipped):
Displays the exterior air temperature
(E TEMP) in degrees Celsius (°C) or Fahrenheit (°F).
Chronometer: Allows to measure an
interval of time in hours and minutes
(hh:mm).
1
1. Press to change display mode
29
smo2003-005a.book Page 30 Friday, November 1, 2002 8:25 AM
Message Display
The information center features a display area that blinks a message whenever one of the following circumstances occurs:
• fuel injection system sensors and major components (MAINT).
• compass error (COMPAS)
• maintenance (MAINT)
• engine overheating (H-TEMP)
• low fuel (FUEL-LO)
• low oil (OIL LOW)
• low voltage (12 V LOW)
A message will sound when one of the
four last circumstances occurs.
Except for low fuel and low oil, which
can be corrected by refilling, it is recommended to see an authorized SEA-DOO
dealer when other messages occur.
The warning light will blink at the same
time.
Warning Light
The red warning LED (Light-Emitting
Diode) blinks along with the message
display to catch your attention.
When another display mode is chosen,
the default display will be displayed
back after 4 seconds.
As a self test, all LCD segments and the
LED will turn on for 3 seconds each time
the information center is activated.
In the event of a warning message, the
message will blink and override the
units display.
If more than one warning message occurs, the blinking messages will scroll
every 4 seconds.
Other Functions
The following describes how to select
other available functions.
Language Option
While in the clock/compass mode:
Fuel Level Display
Bar gauge continuously indicates the
amount of fuel in the fuel tank while
riding. A low-fuel condition is also indicated when it occurs. See Message Display above.
F00L2BZ
Display Priorities
The clock, (clock/compass, if so equipped)
is the default display mode. The default display is the one that appears
when the information center is first activated or displayed back after an alternate display was chosen.
The tachometer, speedometer and
chronometer, are the only other modes
that may be chosen to replace the default display. When one of these is selected, it will become the default display until it is changed again.
30
1
F00L2B0
1. Press and hold for 2 seconds
1
1. Repeatedly press
F00L2B0
1. Press to end
1
smo2003-005a.book Page 31 Friday, November 1, 2002 8:25 AM
English/Metric System
Allows to display the units in the metric
system or in the SAE English system.
F00L2B1
1
1. Press TOGETHER to end
1
F00L2B1
1. Press TOGETHER and hold for 2 seconds
Clock Adjustment
While in the clock/compass mode:
NOTE: If MODE and SET buttons are
not pressed at the end, the default display will come back after 10 seconds
and the time entered will remain.
Chronometer
While in the chronometer mode:
1
F00L2B1
1. Press TOGETHER and hold for 2 seconds
F00L2B0
1
1. Press to start or stop chronometer
F00L2BZ
1
1. Repeatedly press to adjust HOURS
F00L2B0
1
1. Press and hold for 2 seconds to reset
Chronometer is reset every time engine is turned off.
F00L2B0
1
1. Repeatedly press to adjust MINUTES
31
smo2003-005a.book Page 32 Friday, November 1, 2002 8:25 AM
Maintenance Information
When the watercraft is due for a maintenance inspection, the message MAINT
will blink.
To clear the warning message while it
is blinking:
10) Oil Injection Reservoir
Cap
Refer to the vehicle illustration for oil
injection reservoir cap location.
To add injection oil in the reservoir, unscrew the cap counterclockwise. Do
not overfill. Reinstall cap and fully tighten it.
WARNING
1
F00L2B0
1. Press and hold for 2 seconds to reset
NOTE: If maintenance message
(MAINT) continues to blink, it indicates
a fault with the fuel injection system.
Refer to an authorized SEA-DOO dealer for servicing.
8) Glove Box
A small, convenient storage compartment for personal articles.
9) Fuel Tank Cap
Refer to the vehicle illustration for fuel
tank cap location.
Unscrew the cap counterclockwise. After fueling, reinstall cap and fully tighten.
WARNING
Always stop the engine before refueling. Fuel is inflammable and
explosive under certain conditions. Always work in a well ventilated area. Do not smoke or allow
open flames or sparks in the vicinity. Fuel tank may be pressurized,
slowly turn cap when opening.
Never use an open flame to check
fuel level. When fueling, keep watercraft level. Do not overfill or top
off the fuel tank and leave watercraft in the sun. As temperature increases, fuel expands and might
overflow. Always wipe off any fuel
spillage from the watercraft. Periodically verify fuel system.
32
Do not overfill. Reinstall cap and
fully tighten. Oil is inflammable.
Always wipe off any oil spillage
from the bilge.
Open the front storage compartment
cover to expose reservoir cap.
11) Front Storage
Compartment Cover
It gives access to the front storage compartment. Always relatch cover after
closing.
Front Storage Compartment
A convenient watertight area, to carry
personal articles. Ideal location for spare
spark plugs, towrope, first aid kit, etc.
WARNING
Never leave any heavy or breakable
objects loose in the storage area/
basket. Never store or carry anything below basket (if so equipped).
Never operate the watercraft with
any storage compartment cover
open.
Fire extinguisher (sold separately) should
not be loose in the front storage compartment.
smo2003-005a.book Page 33 Friday, November 1, 2002 8:25 AM
12) Front Storage
Compartment Cover
Latch
Pull the latch lever upward in order to
open the front storage compartment
cover. Always relatch.
NOTE: Verify periodically the lock pin
tightness of storage cover. Tighten if
needed and make sure storage cover
latches properly.
13) Side Storage
Compartments
Two convenient watertight compartments to carry personal articles. Ideal
location for water skis or wakeboards.
Left side storage compartment is also
provided with a holder. Tool kit is inserted in that holder.
WARNING
Never leave any heavy or breakable objects loose in the storage
compartment. Never operate the
craft with the storage compartment cover open.
16) Air Intake Opening
This is where air enters to supply the
engine and to ventilate the engine compartment. If the air intake opening is
kept under water, water will get inside
bilge.
CAUTION: If the air intake opening
is kept under water, such as turning
constantly in tight circles, water will
get inside bilge, which may cause
severe damage to internal parts of
the engine.
17) Seat Strap
The seat strap provides a handhold to
assist boarding and is used as a handhold for the passenger.
18) Seat Latch
Removing the seat allows access to
the engine compartment.
The seat latch is located at the rear end
and underneath the seat.
14) Underseat Storage
Compartments
Convenient watertight, removable basket to carry personal articles. Remove
seat to gain access to underseat storage compartments.
WARNING
Never leave any heavy or breakable objects loose in the storage
compartment. Never operate the
craft with the storage compartment cover open.
15) Tool Kit
Contains tools needed to perform basic
watercraft maintenance.
F17L0EY
1
TYPICAL
1. Seat latch
To remove seat, pull the latch lever upward and hold. Lift and pull the seat
rearward.
NOTE: It is necessary to remove the
seat extension first and repeat the
same procedure to remove the seat.
33
smo2003-005a.book Page 34 Friday, November 1, 2002 8:25 AM
Engine Compartment
This is where the mechanical, electrical and fuel/oil systems are located.
WARNING
19) Seat Extension Latch
Removing the seat extension allows
access to the rear storage basket. It
also gives access to the seat latch.
Components inside engine compartment may be hot. When starting
or operating the engine, do not
touch any electrical part. Never
leave any object, rag, tool, etc., in the
engine compartment or in the bilge.
When reinstalling the seat, insert seat
hook into body front tab for each portion of the seat.
F17L0FY
2
1
1. Seat extension latch
2. Rear grab handle
20) Rear Storage Basket
(if so equipped)
A convenient watertight, removable
basket to carry personal articles.
2
F06L12Y
1
1. Insert this tab in hook
2. Hook
To latch seat, align latch hole with pin
then, firmly push downward on rear of
the seat.
F17L09Y
TYPICAL
21) Sun Deck
A convenient space to rest or take some
sun while anchored.
WARNING
Do not start or operate the craft if
a person is seated on the sun deck.
F00L2TY
1
1. Latch hole
2. Pin
34
2
smo2003-005a.book Page 35 Friday, November 1, 2002 8:25 AM
22) Bow and Stern Eyelets
Bow Eyelet
Eyelets can be used for mooring, towing and as a tie-down point during trailering.
1
CAUTION: Do not use the cleats for
securing baggage or as a tie-down
point for trailering or mooring. Never
use mooring cleats to pull or lift the
watercraft.
1
F07L0XY
TYPICAL
1. Fender cleats (each side)
F00L0EY
1. Bow eyelet
24) Footboard
Stern Eyelet
This eyelet allows a rope with a hook,
a closed end or an open end to be attached.
User’s feet should rest on the footboard
when riding.
25) Boarding Platform
Provides a large surface for easier boarding from rear of watercraft.
26) Boarding Step
A convenient step to help reboarding
the watercraft.
F07L0YY
1
TYPICAL
1. Stern eyelet
23) Fender Cleats
These cleats can be temporarily used for
docking, while refueling for fender installation.
F07L1HY
1
TYPICAL
1. Boarding step
35
smo2003-005a.book Page 36 Friday, November 1, 2002 8:25 AM
Pull down the step with your hand and
hold until a foot is put on the step.
WARNING
Engine should be OFF when using
boarding step. Keep limbs away
from jet or intake grate. Stay on
center of the step. Only one person
at the time on the step. Never use
the step for pulling, towing, diving or jumping, boarding a PWC
that is out of water or any other purpose other than a boarding step.
When engine is running, water should
flow from the outlet. This allows air in
engine cooling system to escape. It
also indicates that water is circulating
in the cooling system.
NOTE: It may be required to increase
slightly the engine RPM to see the water flowing out.
CAUTION: Should water not flow
from outlet a few seconds after engine starts, immediately stop engine
and refer to POST-OPERATION CARE
and look for Cooling System Flushing or refer to an authorized SEA-DOO
dealer for servicing.
28) Deck Drains
They provide drainage of water from
rain, deck washing, water splashing,
etc. Keep clean to avoid clogging.
29) Flushing Connector
F00L2UY
27) Cooling System Bleed
Outlet
A convenient connector is provided to
allow easy installation of a garden hose
to flush the cooling system.
Refer to POST-OPERATION CARE section for proper use.
30) Bilge Drain Plugs
Should water be found in the bilge, it
can be easily drained by unscrewing
the drain plugs when engine is off and
watercraft is out of water.
CAUTION: Remove boat from water
prior to unscrewing drain plugs.
1
F01L94Y
TYPICAL
1. Bleed outlet
36
F17L0HZ
TYPICAL
1. Drain plugs
1
smo2003-005a.book Page 37 Friday, November 1, 2002 8:25 AM
1
2
F02L2FY
1. Unscrew
2. Tighten
Tilt the watercraft slightly to the rear
so that the water can completely flow
out of the bilge.
It is suggested to drain bilge on a ramp.
CAUTION: Make sure drain plugs
are properly secured prior to launching the watercraft in water.
31) Automatic Bilge Pump
Bilge pump evacuates water from the
bilge.
When safety lanyard cap is plugged to
the switch, bilge pump automatically
turns on. It will stay on for 30 seconds.
When engine is started bilge pump remains on and stays on until engine is
stopped. When engine is stopped
pump remains on for 30 seconds and
then automatically shuts-off.
1
F07L1HZ
TYPICAL
1. Reverse gate
34) Jet Pump Water Intake
The water is drawn up by the impeller
through this opening. The water intake
grate minimizes the entry of foreign
objects into the propulsion system.
WARNING
Keep away from intake grate while
engine is on. Items such as long
hair, loose clothing or personal flotation device straps can become
entangled in moving parts resulting in severe injury or drowning.
32) Jet Pump Nozzle
Jet pump nozzle turns side to side via
rider input at the handlebar. This provides directional control when engine
is running.
WARNING
Never use nozzle as a supporting
point to board the craft or to lift it.
33) Reverse Gate
When selecting the neutral or reverse
position with the shift lever, the reverse gate moves up or down to obtain
the desired position.
F01J3ZY
1
TYPICAL
1. Water intake
35) Fuses
Fuses are located in bilge. Refer to MAINTENANCE for more details.
36) Battery
Battery is located inside engine compartment. Refer to SPECIAL PROCEDURES.
37
smo2003-005a.book Page 38 Friday, November 1, 2002 8:25 AM
FUEL AND LUBRICATION
CAUTION: Scrupulously follow the
instructions of this section. Failure
to do so may reduce the engine’s life
and/or performance.
Fueling Procedure
WARNING
Follow these safe boating fueling
instructions explicitly.
Turn off engine.
Do not allow anyone to remain on the
watercraft.
Tie watercraft securely to the fueling pier.
Have a fire extinguisher close at hand.
Do not insert the spout too far in filler
neck.
Pour fuel slowly so that air can escape
from the tank and prevent fuel flowback. Be careful not to spill fuel.
Stop filling when the fuel reaches the
bottom of filler neck. Do not fill into the
filler tube to prevent fuel spillage. Do
not overfill. Fully tighten fuel tank cap.
WARNING
Always stop the engine before refueling. Fuel is inflammable and
explosive under certain conditions. Always work in a well ventilated area. Do not smoke or allow
open flames or sparks in the vicinity. Fuel tank may be pressurized,
turn cap slowly when opening.
Never use an open flame to check
fuel level. When fueling, keep watercraft level. Do not overfill or top
off the fuel tank and leave watercraft in the sun. As temperature increases, fuel expands and might
overflow. Always wipe off any fuel
spillage from the watercraft. Periodically verify fuel system.
38
Recommended Fuel
Use unleaded regular gasoline with 87
octane (Ron + Mon)/2 specification.
NOTE: Adding injection oil in the fuel
tank for the break-in has no noticeable
effects on a DI engine.
CAUTION: Never experiment with
other fuels or fuel ratios. Never use
fuel containing more than 10% alcohol, (ethanol or methanol). The use
of non-recommended fuel can result
in watercraft performance deterioration and damage to critical parts in
the fuel system and engine components.
CAUTION: Never use injector cleaning products. They may contain additive that could damage injector components.
Recommended Oil
WARNING
Do not overfill. Reinstall cap and
fully tighten. Oil is inflammable.
Always wipe off any oil spillage
from the bilge.
Use only two-stroke engine injection
oil sold by authorized SEA-DOO dealers.
MODEL
OIL TYPE
LRV DI
BOMBARDIER
Formula XP-S II
synthetic injection oil
(or equivalent)
CAUTION: BOMBARDIER Formula
XP-S II oil is specially formulated
and tested for use in our 947 DI engines. Use of any other brand of twostroke oil may void the limited warranty. Use only BOMBARDIER Formula XP-S II oil (or equivalent oil).
smo2003-005a.book Page 39 Friday, November 1, 2002 8:25 AM
BOMBARDIER injection oil is a blend
of basic oil and additives especially selected to ensure unequalled lubrication, engine cleanliness and minimum
spark plug fouling.
The BOMBARDIER Formula XP-S II
synthetic injection oil provides superior lubrication, reduced engine component wear and oil deposit, thus
maintaining maximum-level performance and antifriction properties. This
synthetic injection oil meets the latest
ASTM and JASO standards by ensuring high biodegradability and low exhaust smoke.
CAUTION: Never use four-stroke petroleum or synthetic motor oil and
never mix these with outboard motor oil. Do not use NMMA TC-W, TCW2 or TC-W3 outboard two-stroke
engine oils or ashless two-stroke engine oils. Avoid mixing different
brands of API TC oil as resulting chemical reactions may cause severe engine damage.
Oil Injection System
This watercraft features an oil injection
system which does not require manual
fuel/oil mixing.
A sufficient amount of injection oil
should be maintained in the reservoir.
NOTE: It is recommended to carry a 1 L
of spare injection oil.
The use of a funnel is recommended
to pour the oil into the reservoir. Stop
filling as soon as oil appears at approximately 13 mm (1/2 in) from top of reservoir. Do not overfill.
CAUTION: Always maintain a sufficient amount of injection oil in the oil
reservoir. Check and refill every time
you refuel if necessary. Do not overfill.
If the engine runs out of oil, severe engine damage will occur. If the oil reservoir is found almost empty, air can
enter in the system and it should be
bled. Immediately refer to an authorized SEA-DOO dealer to have the oil
injection system inspected.
39
smo2003-005a.book Page 40 Friday, November 1, 2002 8:25 AM
BREAK-IN PERIOD
CAUTION: Scrupulously follow the
instructions of this section. Failure
to do so may reduce the engine’s life
and/or performance.
With SEA-DOO watercraft powered by
Rotax® engines, a break-in period of 10
hours is required before continuous
operation at full throttle.
With the DI engine, in order to achieve
a good break-in, vary the engine speed
every few minutes with brief wide
open throttle accelerations of up to 15
seconds.
CAUTION: Continued wide open
throttle runs and prolonged cruising
without speed variations should be
avoided, this can cause engine damage during the break-in period.
CAUTION: Remove and clean spark
plugs after engine break-in.
NOTE: Adding injection oil in the fuel
tank for the break-in has no noticeable
effects on a DI engine.
10-Hour Inspection
It is highly recommended that after the
first 10 hours of operation, the watercraft be checked by an authorized
SEA-DOO dealer. This inspection will
also provide the opportunity to discuss
the unanswered questions you may
have encountered during the first hours
of operation.
The 10-hour inspection is at the expense of the watercraft owner.
40
smo2003-005a.book Page 41 Friday, November 1, 2002 8:25 AM
PRE-OPERATION CHECKS
WARNING
The pre-operation check is very important prior to operating the watercraft.
Always check the proper operation of critical controls, safety features and
mechanical components, before starting as listed hereinafter. If not done
as specified here, severe injury or death might occur. Bring all safety equipment required by local laws.
Some of the following items may not have been previously covered in this guide,
however they will be described in the MAINTENANCE or SPECIAL PROCEDURES
section. Please refer to these sections to have more detailed information.
WARNING
Engine should be off and the safety lanyard should always be removed
from its post prior to verifying any of the following points. Only start watercraft once all items have been checked and operate properly.
ITEM
OPERATION
Hull
Inspect.
Jet pump water intake
Inspect/clean.
Bilge
Drain. Ensure plugs are secured.
Battery
Inspect tightness of cables and retaining
strap(s).
Fuel tank and oil reservoir
Refill.
Engine compartment
Check fuel line connections for tightness.
Verify for any fuel leak/odor.
Steering system
Check operation.
Throttle system
Check operation.
Shifter system
Check operation.
✓
Storage compartment covers and Ensure they are closed and latched.
seat
Safety lanyard and engine
start/stop button
Check operation.
NOTE: See the detailed instructions hereinafter.
41
smo2003-005a.book Page 42 Friday, November 1, 2002 8:25 AM
Hull
Battery
Inspect hull for cracks or damage.
Jet Pump Water Intake
Remove weeds, shells, debris or anything else that could restrict the flow
of water and damage cooling system
or propulsion unit. Clean as necessary.
If any obstruction can not be removed,
refer to an authorized SEA-DOO dealer
for servicing.
WARNING
Verify tightness of battery cables to
their posts and condition of battery
retaining strap(s)/fasteners. Do not
charge or boost battery while installed.
Fuel Tank and Oil Reservoir
With the watercraft horizontal, fill the
fuel tank to specified level.
Check the oil level and refill reservoir
as necessary.
Check fuel tank and oil reservoir retaining straps/fasteners.
Engine Compartment
WARNING
1
F01J3ZY
TYPICAL
1. Inspect this area
Inspect leading edges of the impeller,
if they have nicks or bends performance will be greatly reduced.
Bilge
Should water be present in the bilge,
tilt the watercraft to the rear and unscrew drain plugs to completely empty
the bilge.
Secure bilge drain plugs.
WARNING
Make sure drain plugs are properly secured prior to launching the
watercraft in water.
42
Should any leak or gasoline odor
be present, do not start the engine.
Refer to an authorized SEA-DOO
dealer before use.
Steering System
Assisted by another person, check
steering operation for free movement.
When the handlebar is horizontal, the
jet pump nozzle should be in the straight
ahead position. Ensure the jet pump
nozzle pivots easily and in the same direction as the handlebar.
WARNING
Check handlebar and corresponding steering nozzle operation before starting.
smo2003-005a.book Page 43 Friday, November 1, 2002 8:25 AM
Throttle System
Check throttle lever for free and smooth
operation. It should return to its initial
position immediately after it is released.
WARNING
Check throttle lever operation before starting the engine.
Shifter System
Check reverse gate operation for free
movement. With shift lever in forward
position, the gate should be in upward
position. With the shift lever in neutral
position, gate should be in middle position. With shift lever in reverse position,
gate should be in downward position.
WARNING
Verify the reverse gate operation
before starting the engine.
Storage Compartment
Covers and Seat
Ensure they are closed and latched.
WARNING
Make sure seat is securely latched.
Safety Lanyard and Engine
Start/Stop Button
Position shift lever in neutral. Ensure that
both switches operate properly. Start engine and stop it using each switch individually.
WARNING
Should the safety lanyard cap is
loose or fail to remain on its post,
replace it immediately in order to
avoid unsafe use.
43
smo2003-005a.book Page 44 Friday, November 1, 2002 8:25 AM
OPERATING INSTRUCTIONS
WARNING
Always perform the PRE-OPERATION
CHECKS before operating the watercraft. Become thoroughly familiar with all controls and the function
of each. Should any control or instruction not be fully understood,
refer to an authorized SEA-DOO
dealer.
Principle of Operation
Propulsion
The engine is directly coupled to a drive
shaft which, in turn, rotates an impeller. This impeller is accurately adjusted
in a housing where the water is drawn
up from underneath the watercraft.
Then the water flows through the impeller to a venturi. The venturi accelerates the water and produces thrust to
move the watercraft. Depressing the
throttle lever increases engine speed
and therefore watercraft speed.
Keep away from intake grate while
engine is on. Items such as long
hair, loose clothing or personal flotation device straps can become
entangled in moving parts resulting in severe injury or drowning.
The shift lever should be in the forward
position in order for the watercraft to advance.
Neutral and Reverse
WARNING
Never use jet pump components as
a supporting point to board the watercraft. Shift lever should only be
used when the engine is idling and
watercraft is completely stopped.
Never rev the engine at high RPM
in reverse. Do not use reverse to
stop the watercraft. Only use reverse at slow speed and for the
shortest time possible. Always ensure the path behind is clear of objects and persons including children playing in shallow water.
To find the neutral, set in reverse then
push back until the watercraft stops
moving backwards.
The reverse gate will be in the middle
position, directing half of the thrust toward the front of the watercraft to minimize watercraft movement.
F01J3YY
TYPICAL
WARNING
Whenever the engine is to be started, the operator and passenger(s)
should always be properly sitting
on the watercraft and be wearing
protective clothing including a
Coast Guard approved PFD and a
wet suit bottom.
44
WARNING
WARNING
When the watercraft is in neutral
position, the drive shaft and impeller are still turning.
smo2003-005a.book Page 45 Friday, November 1, 2002 8:25 AM
1
F07J0OY
1
F07L0RY
TYPICAL
1. Shift lever in neutral position
F07J0NY
1
TYPICAL
1. Reverse gate in downward reverse position
NOTE: To obtain maximum efficiency
and control from the reverse, increase
engine speed to slightly above idle.
Too much RPM will create water turbulence and reduce reverse efficiency.
In reverse position, turn the handlebar
in the opposite direction that you want
to move the rear of the watercraft.
For example, to steer the rear of the
watercraft to the left side, turn the handlebar to the right side.
1
TYPICAL
1. Reverse gate in middle neutral position
2
To obtain reverse, pull shift lever completely. The reverse gate will be in downward position, directing all the thrust toward the front of the watercraft.
F07A0CY
TYPICAL
1. Handlebar turned to the right side
2. Rear of watercraft moving to the left side
WARNING
F07L0SY
1
TYPICAL
1. Shift lever in reverse position
Shift lever should only be used when
the engine is idling and watercraft is
completely stopped. Do not use reverse to stop the watercraft.
45
smo2003-005a.book Page 46 Friday, November 1, 2002 8:25 AM
Steering
Boarding the Watercraft
General
As with any watercraft, boarding should
be done carefully and engine should not
be running.
WARNING
Turning the handlebar pivots the jet
pump nozzle which controls the watercraft direction. Turning the handlebar to
the right will turn the watercraft to the
right and inversely. The throttle should
be applied to turn the watercraft.
Engine should be OFF when boarding the watercraft or when using
boarding step (if so equipped).
Keep limbs away from jet or intake
grate. Stay on center of the step.
Only one person at a time on the
step. Never use the step for pulling,
towing, diving or jumping, boarding a watercraft that is out of water
or any other purpose other than a
boarding step.
WARNING
On some models, boarding is facilitated by using a step.
F07A0AY
Throttle should be applied and
handlebar turned to change the direction of the watercraft. Steering
efficiency will differ depending on
the number of passengers, load,
water conditions and environmental factors such as the wind.
Unlike a car, a watercraft needs some
throttle to turn. Practice in a safe area
applying the throttle and turning away
from an imaginary object. This is a good
collision avoidance technique.
WARNING
Directional control is reduced when
the throttle is released and lost when
engine is off.
The watercraft behaves differently with
a passenger and requires greater skill.
The passenger should always grip the
seat strap or grab handle. Reduce
speed and avoid sharp turns. Avoid
choppy water conditions when carrying
a passenger.
46
WARNING
Inexperienced riders should practice
how to get aboard (all methods explained here) close to shore first
before venturing into deep water.
WARNING
Never use jet pump components
as a supporting point to board the
watercraft.
Boarding from a Dock or in
Shallow Water
When boarding from a dock, slowly
place one foot on the watercraft footboard nearest the dock and, at the
same time, transfer the body weight to
the other side in order to balance the
watercraft while holding the handlebar.
Then, bring the other foot over the seat
and put it on the other footboard. Push
the watercraft away from the dock.
smo2003-005b.fm Page 47 Tuesday, November 5, 2002 1:38 PM
Grip the grab handle and pull yourself
upward until your knee can reach the
boarding platform then grip the seat
strap.
F07A0BY
F01L4JY
TYPICAL
Bring your feet on the footboard while
maintaining balance.
A
F01L4KY
F01L4WY
A. 90 cm (3 ft)
In shallow water, board the watercraft
either from the side or the rear.
Boarding in Deep Water
Operator Alone
Swim to the rear of the watercraft.
Sit astride the seat.
Operator with a Passenger
The operator climbs on the watercraft
the same way as explained previously.
In choppy water, the passenger, while
in the water, may hold the watercraft
to help the operator in climbing aboard.
F01L5JY
F01L4MY
47
smo2003-005b.fm Page 48 Tuesday, November 5, 2002 1:38 PM
The passenger then climbs on the watercraft while the operator maintains
balance by sitting as close as possible
to the console.
F01L4NY
F01L4OY
Starting
Preparation
Before unloading the watercraft from
the trailer, it can be started for about
10 seconds to verify proper operation.
 WARNING
Components inside engine compartment may be hot. Do not touch
electrical parts or jet pump area
when engine is running.
Attach the safety lanyard to your PFD
and snap the cap to its post before starting the engine.
NOTE: If you hear more than 2 short
beeps from DESS system, it indicates
a particular condition that should be
corrected. Refer to the TROUBLESHOOTING section for the meaning of
the coded signal.
48
 WARNING
Before starting the engine, the operator and passengers should always be properly seated.
Position shift lever to neutral.
Firmly grip handlebar with your left hand
and place both feet on the footboard.
To start engine, depress and hold the engine start/stop button. Follow procedure
below for cold or warm engine starting.
If engine fails to start after 10 seconds,
wait a few seconds then repeat procedure.
CAUTION: Do not hold start/stop button more than 30 seconds to avoid
starter overheating. A rest period
should be observed between the
cranking cycles to let starter cool
down. Pay attention not to discharge
battery. The engine should be started only after boarding, when there is
at least 90 cm (3 ft) of water below
the hull. Do not accelerate fast.
Release engine start/stop button immediately after engine is started.
Cold or Warm Engine
Do not depress the throttle lever to start
either a cold or warm engine.
Riding
Slowly accelerate to reach deeper water. Do not apply full throttle until the
engine is warm.
F07A0DY
TYPICAL
CAUTION: Avoid watercraft operation
in weeded areas. If unavoidable, vary
watercraft speed.
smo2003-005a.book Page 49 Friday, November 1, 2002 8:25 AM
Rough Water or Poor
Visibility Operation
Avoid operation in these conditions. If
you must do so, proceed with caution
and prudence using minimum speed.
Crossing Waves
Reduce speed.
Always be prepared to steer and balance
as necessary.
When crossing wakes, always keep a
safe distance from watercraft ahead.
Beaching
CAUTION: It is not recommended to
run the watercraft to the beach.
Come slowly to the beach and shut off
the watercraft using the safety lanyard
when water depth is 90 cm (3 ft) under
the hull, then pull the watercraft to the
beach.
WARNING
When crossing wakes, slow down.
Operator and passenger(s) can
brace themselves by posting. Do
not jump waves or wakes.
F07A0EY
Stopping/Docking
Shutting Off the Engine
The watercraft is slowed by water drag.
The stopping distance will vary depending on the watercraft size, weight,
speed, water surface condition, presence and direction of wind and current.
The operator should become familiarized with the stopping distance under
different conditions.
Release the throttle at a sufficient distance before the expected landing area.
Reduce speed to idle.
On models equipped with shifter system, shift to neutral, reverse or forward,
as required.
To keep watercraft directional control,
the engine should be running until the
watercraft is at idle.
To shut off the engine, completely release throttle lever and press the engine start/stop button. Remove safety
lanyard from watercraft.
WARNING
WARNING
Should the engine be shut off, watercraft directional control is lost.
Never leave the safety lanyard on
its post when watercraft is not in
operation in order to prevent accidental engine starting or to avoid
unauthorized use by children or
others or theft.
Directional control is reduced when
the throttle is released and lost
when engine is off.
49
smo2003-005a.book Page 50 Friday, November 1, 2002 8:25 AM
POST-OPERATION CARE
WARNING
Allow engine to cool before performing any maintenance.
Engine lubrication and flushing should
be performed when the watercraft is
not expected to be used further the
same day or when the watercraft is
stored for any extended time.
WARNING
General Care
Remove the watercraft from the water
every day to prevent marine organisms
growth.
Should any water be present in the hull,
unscrew the drain plugs and tilt the watercraft to the rear in order to allow water to flow out.
Wipe up any remaining fluid in the engine compartment (bilge, engine, battery, etc.) with clean dry rags (this is particularly important in salt water use).
Additional Care for Foul
Water or Salt Water
When the watercraft is operated in foul
water and particularly in salt water, additional care should be taken to protect
the watercraft and its components.
Rinse trailer and watercraft‘s bilge area
with fresh water.
CAUTION: Failure to perform proper
care such as: watercraft rinsing,
cooling system flushing and anticorrosion treatment, when watercraft is
used in salt water, will result in damage to the watercraft and its components. Never leave the watercraft
stored in direct sunlight.
Cooling System Flushing
and Engine Internal
Lubrication
General
Flushing the cooling system with fresh
water is essential to neutralize corroding effects of salt or other chemical products present in water. It will help to remove sand, salt, shells or other particles
in water jackets (engine, exhaust manifold, tuned pipe) and/or hoses.
50
Perform this operation in a well ventilated area.
Proceed as follows:
Clean jet pump by spraying water in its
inlet and outlet and then apply a coating of BOMBARDIER LUBE lubricant
or equivalent.
Connect a garden hose to connector
located at the rear of watercraft on jet
pump support.
NOTE: A quick connect adapter can be
used (P/N 295 500 473). No hose pincher is required to flush engine.
F07E01Y
3
2
1
TYPICAL
1. Hose adapter
2. Quick connect adapter (not mandatory)
3. Garden hose
NOTE: The quick connect adapter may
be supplied with some models. It has
to be removed if you do not use a quick
connect adapter on your garden hose.
smo2003-005a.book Page 51 Friday, November 1, 2002 8:25 AM
Flushing
To flush cooling system, start the engine then immediately open the water
tap.
Close the water tap then stop the engine.
CAUTION: Always close the water tap
before stopping the engine.
WARNING
Final Steps
Disconnect the garden hose.
Remove spark plug cables and connect
them on the grounding device.
Components inside engine compartment may be hot. Do not touch
any electrical parts or jet pump
area when engine is running.
CAUTION: Never flush a hot engine.
Always start the engine before opening the water tap. Open water tap
immediately after engine is started
to prevent overheating.
Run the engine about 3 minutes at a
fast idle around 3500 RPM.
Ensure water flows out of drain lines
(engine crankcase, engine cylinder and
air compressor while flushing. Otherwise, clean the lines.
CAUTION: Never run engine longer
than 5 minutes. Drive line seal has
no cooling when watercraft is out of
water.
Lubrication
Spray BOMBARDIER LUBE lubricant
or equivalent, through hole of air intake
silencer keeping engine at fast idle
during one minute.
1
F02H0ZY
WARNING
Always use spark plug cable grounding device when removing spark
plugs.
F01H7DY
1
1. Grounding device
Remove both spark plugs and spray
BOMBARDIER LUBE lubricant or equivalent into each cylinder.
To prevent fuel to be injected and also
to cut the ignition at the engine starting, proceed as follows.
While engine is stopped, fully depress
throttle lever and HOLD for cranking.
NOTE: A 1 second beep every second
indicates the drowned mode is active.
Crank the engine a few turns to distribute the oil on cylinder wall.
Apply anti-seize lubricant on spark plug
threads then reinstall them.
2
1. Air intake silencer
2. Spray BOMBARDIER LUBE here
51
smo2003-005a.book Page 52 Friday, November 1, 2002 8:25 AM
Properly reconnect spark plug cables
to spark plugs.
WARNING
Always reconnect spark plug cables at the same spark plugs where
they come from. The cable coming
out the edge of the electrical box
must be connected to the MAG side
spark plug.
Wipe up any residual water from the engine.
Anticorrosion Treatment
To prevent corrosion, spray a corrosion
inhibitor (salt water resistant) such as
BOMBARDIER LUBE lubricant or equivalent over metallic components in engine compartment.
Apply dielectric grease (salt water resistant) on battery posts and cable connectors.
CAUTION: Never leave rags or tools
in the engine compartment or in the
bilge.
52
smo2003-005a.book Page 53 Friday, November 1, 2002 8:25 AM
SPECIAL PROCEDURES
Limp Home Mode
Monitoring System
To assist you when using the watercraft, a system monitors the electronic
components of the fuel injection system and some components of the
electrical system. When a fault occurs,
it sends visual messages through the
information center and/or audible signals through a beeper to inform you of
a particular condition. Refer to the INFORMATION CENTER for the displayed
messages and the TROUBLESHOOTING section for the beeper coded signals chart.
Limp Home Modes
Besides the signals as seen above, the
system may automatically set default
parameters to the MPEM to ensure
the adequate operation of the watercraft if a component of the fuel injection system is not operating properly.
Depending on the severity of the malfunction, the watercraft speed may be
reduced and not allowed to reach its
top speed as usual. In this case, letting
the engine returning at idle speed may
allow normal operation to come back.
The engine RPM may be limited to idle
if some critical components fail. In this
case, removing and reinstalling the
safety lanyard on its post may allow
normal operation to come back.
These performance-reduced modes
allow the rider to go back home which
would not be possible without this advanced system. If this occurs, see an
authorized SEA-DOO dealer as soon as
possible for inspection.
Engine Overheating
CAUTION: If the monitoring beeper
continuously sounds, stop engine immediately.
Perform Jet Pump Water Intake and
Impeller Cleaning procedure described
in this section.
When back to shore, flush cooling system, refer to POST-OPERATION CARE.
If engine still overheats, refer to an authorized SEA-DOO dealer for servicing.
Jet Pump Water Intake and
Impeller Cleaning
WARNING
Keep away from intake grate while
engine is on. Items such as long
hair, loose clothing or personal flotation device straps can become
entangled in moving parts resulting in severe injury or drowning.
Weeds, shells or debris can get caught
on the intake grate, drive shaft and/or
impeller. A clogged water intake may
cause troubles such as:
1. Cavitation: Engine speed is high but
watercraft moves slowly due to reduced jet thrust, jet pump components may be damaged.
2. Overheating: Since the jet pump
operation controls the flow of water
to cool the engine, a clogged intake
will cause the engine to overheat
and damage engine internal components.
A weed clogged area can be cleaned
as follows:
In-Water Cleaning
Rock the watercraft several times while
repeatedly pressing engine start/stop
button for short period without starting
engine. Most of the time, this will remove the blockage. Start engine and
make sure water flows out from bleed
outlet and watercraft operates properly.
53
smo2003-005a.book Page 54 Friday, November 1, 2002 8:25 AM
If system is still blocked, move the watercraft out of the water and remove
blockage manually.
If the aforementioned method does not
work, the following can be performed:
– With engine running and before applying throttle, put shift lever in reverse position and vary throttle quickly several times.
– Repeat procedure if necessary.
CAUTION: Inspect water intake grate
for damage. Refer to an authorized
SEA-DOO dealer for repair as necessary.
Capsized Watercraft
The watercraft is designed so that it
should not turn over easily. Also two
sponsons mounted on the side of the
hull assist watercraft stability. If it turns
over, it will remain capsized.
WARNING
On-Beach Water Cleaning
WARNING
Always remove safety lanyard cap
from its post to prevent accidental
engine starting before cleaning
the jet pump area.
Place a cardboard or a carpet beside the
watercraft to prevent scratching when
turning the watercraft for cleaning.
Rotating watercraft in the proper direction eliminates the possibility of residual water in the tuned pipe entering the
engine and causing engine damage.
Rotate the watercraft clockwise (seen
from rear) to its right side for cleaning.
When watercraft is capsized, do
not attempt to restart the engine.
Operator and passengers should
always wear approved personal
flotation devices.
CAUTION: Always refer to decal located on stern of watercraft.
To return the watercraft upright, ensure the engine is off, grab the inlet
grate, step on bumper rail and use your
weight to rotate the watercraft.
Rotate the watercraft counterclockwise (seen from rear).
Max. 90°
F06L0DZ
Submerged Watercraft
F06L11Y
Clean the water intake area. If the system is still clogged, refer to an authorized SEA-DOO dealer for servicing.
54
If the watercraft is submerged and engine is water-flooded, it is strongly recommended that the watercraft be serviced by an authorized SEA-DOO dealer.
smo2003-005a.book Page 55 Friday, November 1, 2002 8:25 AM
Water-Flooded Engine
Out of Fuel
In the event the engine cannot be serviced within a few hours, remove spark
plug cables and connect them on the
grounding device.
When running the engine out of fuel,
it may be necessary to remove and install the safety lanyard 2 - 3 times to
initially feed the fuel system after fuel
tank refill.
WARNING
Never crank engine with spark
plugs removed unless spark plug
cables are connected to the grounding device. Be careful when cranking engine, water will spray out
from spark plug holes.
Remove spark plugs and dry them with
a clean and dry cloth.
Cover spark plug holes with a rag.
To prevent fuel to be injected and also
to cut the ignition at the engine starting, proceed as follows.
While engine is stopped, fully depress
throttle lever and HOLD for cranking.
NOTE: A 1 second beep every second
indicates the drowned mode is active.
Crank engine several times to allow water to escape from spark plug openings.
Release throttle lever.
If water does not completely go out, it
may be necessary to remove the air intake silencer then to lean the vehicle so
that water can flow out from throttle
bodies.
Spray BOMBARDIER LUBE lubricant
or equivalent into spark plug holes.
Crank engine again.
Reinstall spark plugs. Install clean dry
spark plugs if possible. Reconnect cables.
WARNING
Always reconnect spark plug cables at the same spark plugs where
they come from. The cable coming
out the edge of the electrical box
must be connected to the MAG side
spark plug.
Towing the Watercraft in
Water
Special precautions should be taken
when towing a SEA-DOO watercraft in
water.
Maximum recommended towing speed
is 24 km/h (15 MPH).
When towing your watercraft in water,
pinch the water supply hose from the
impeller housing to the engine with a
large hose pincher (P/N 529 032 500).
F01B23Y
This will prevent the cooling system
from filling which may lead to water being injected into and filling the exhaust
system. Without the engine running
there isn’t any exhaust pressure to carry the water out the exhaust outlet.
CAUTION: Failure to do this may result in damage to the engine. If you
must tow a stranded watercraft in
water and do not have a hose pincher, be sure to stay well below the
maximum towing speed of 24 km/h
(15 MPH).
Snugly install the hose pincher on the
water supply hose as shown.
Start engine normally.
55
smo2003-005a.book Page 56 Friday, November 1, 2002 8:25 AM
F12E01Y
1
TYPICAL
1. Hose pincher on water supply hose on this
side of the T-fitting
CAUTION: When finished towing the
watercraft, hose pincher should be
removed before operating it. Failure
to do so will result in damage to the
engine.
Low-Charge Battery
Condition
See an authorized SEA-DOO dealer to
have it charged or replaced.
WARNING
Do not charge or boost the battery
while installed on the watercraft.
Electrolyte is poisonous and dangerous. Avoid contact with eyes,
skin and clothing.
56
smo2003-005a.book Page 57 Friday, November 1, 2002 8:25 AM
MAINTENANCE
Maintenance, replacement, or repair
of the emission control devices and
systems may be performed by any
marine SI (spark ignition) engine repair establishments or individual.
Engine Emissions
Information
Manufacturer’s Responsibility
Beginning with 1999 model year engines, PWC manufacturers of marine
engines must determine the exhaust
emission levels for each engine horsepower family and certify these engines
with the United States of America Environmental Protection Agency (EPA).
An emissions control information label, showing emission levels and engine specifications, must be placed on
each vehicle at the time of manufacture.
Dealer’s Responsibility
When performing service on all 1999
and more recent SEA-DOO watercrafts that carry an emissions control
information label, adjustments must
be kept within published factory specifications.
Replacement or repair of any emission
related component must be executed
in a manner that maintains emission
levels within the prescribed certification standards.
Dealers are not to modify the engine
in any manner that would alter the
horsepower or allow emission levels
to exceed their predetermined factory
specifications.
Exceptions include manufacturer’s
prescribed changes, such as altitude
adjustments for example.
Owner Responsibility
The owner/operator is required to have
engine maintenance performed to
maintain emission levels within prescribed certification standards.
The owner/operator is not to, and should
not allow anyone to modify the engine
in any manner that would alter the
horsepower or allow emissions levels to
exceed their predetermined factory
specifications.
EPA Emission Regulations
All new 1999 and more recent SEA-DOO
watercraft manufactured by Bombardier
are certified to the EPA as conforming
to the requirements of the regulations
for the control of air pollution from new
watercraft engines. This certification is
contingent on certain adjustments being set to factory standards. For this
reason, the factory procedure for servicing the product must be strictly followed and, whenever practicable, returned to the original intent of the design.
The responsibilities listed above are
general and in no way a complete listing of the rules and regulations pertaining to the EPA requirements on exhaust emissions for marine products.
For more detailed information on this
subject, you may contact the following
locations:
VIA U.S. POSTAL SERVICE:
Office of Mobile Sources
Engine Programs
and Compliance Division
Engine Compliance Programs
Group (6403J)
401 M St. NW
Washington, DC 20460
VIA EXPRESS or COURIER MAIL:
Office of Mobile Sources
Engine Programs
and Compliance Division
Engine Compliance Programs
Group (6403J)
501 3rd St. NW
Washington, DC 20001
EPA INTERNET WEB SITE:
www.epa.gov
57
smo2003-005a.book Page 58 Friday, November 1, 2002 8:25 AM
WARNING
Only perform procedures as detailed in this guide. It is recommended that the assistance of an authorized SEA-DOO dealer be periodically
obtained on other components/
systems not covered in this guide.
Unless otherwise specified, engine
must not be running and the safety
lanyard must be removed from its
post for all maintenance procedures. Components inside engine
compartment may be hot. Never
use jet pump components to lift the
watercraft.
Lubrication
Use SEA-DOO synthetic grease or equivalent and lubricate PTO flywheel.
Proceed as follows:
Remove seat to expose engine compartment.
Remove vent tube support (if so
equipped).
PTO Flywheel
Remove the fasteners and pull out PTO
flywheel guard.
2
CAUTION: Immediately stop lubricating as soon as PTO flywheel boot
begins to expand to prevent damage
or slipping.
1
F01I0BZ
3
2
1. PTO flywheel
2. Grease fitting
3. PTO flywheel boot
Reinstall and secure PTO flywheel guard.
Anticorrosion Protection
Throttle Cable
Lubricate the throttle cable with BOMBARDIER LUBE lubricant or equivalent.
Electrical Connections
As necessary, apply anticorrosion product such as dielectric grease on battery
posts and all exposed cable connectors.
CAUTION: Do not lubricate connectors of the Multi-Purpose Electronic
Module.
Additional Lubrication
BOMBARDIER LUBE lubricant or equivalent will help prevent corrosion of metallic parts and maintain proper operation of moving mechanisms.
F01I0AY
1
TYPICAL
1. Flywheel guard
2. Fasteners
Using a grease gun, carefully lubricate
PTO flywheel at grease fitting until
PTO flywheel boot begins to expand.
58
WARNING
Do not lubricate the safety lanyard
post.
smo2003-005a.book Page 59 Friday, November 1, 2002 8:25 AM
Seat Opening Mechanism, Tab,
Hook and Lock Pin
1
2
F01L7UY
1. Front tab
2. Rear mechanism
START
STOP
F01L51Y
TYPICAL
Reverse Gate
Lubricate pivoting points and mechanism.
Periodic Inspection
Routine maintenance is necessary for
all mechanized products. A periodic inspection contributes to the product’s
life span.
The following maintenance chart gives
guidelines for regular watercraft servicing scheduled to be performed by
you and/or by an authorized SEA-DOO
dealer. The schedule should be adjusted according to operating conditions
and use.
IMPORTANT: Schedule for watercraft
rental operations or higher number of
hour use, will require greater frequency of inspection and maintenance.
59
smo2003-005a.book Page 60 Friday, November 1, 2002 8:25 AM
Periodic Inspection Chart
LUBRICATION
SYSTEM
FUEL
SYSTEM
COOLING
SYSTEM
ENGINE
GENERAL
60
EVERY 25
HOURS OR
3 MONTHS
EVERY 50
HOURS OR
6 MONTHS
EVERY 100
HOURS
OR 1 YEAR
TO BE
PERFORMED
BY
DESCRIPTION
FIRST 10
HOURS
FREQUENCY
Lubrication/corrosion protection
➀
✔
O
Support and rubber mount condition/tightness
Exhaust system fasteners ➃
RAVE valve cleaning ➃
Top end inspection
(leak test, piston and ring clearance) ➃
Counterbalance shaft oil level
Spark plug inspection, cleaning and gap adjustment ➄
Spark plug replacement ➀
TDC setting ➃
Flushing
Hose condition and fasteners
Inspect/clean engine drain tubes
Water flow regulator valve inspection
Throttle cable, inspection/lubrication
Fuel filter and lines inspection
Fuel filter replacement
Visually check for oil leakage between cylinder head
and injector ➃
Fuel injection system sensors (except throttle body),
visual inspection ➃
Throttle body cleaning and their sensors ➃ ➄
Fuel vent line pressure relief valve inspection
Fuel lines, connections, check-valve and fuel system
pressurization ➃
Visual inspection: throttle bodies, sensors, fuel lines,
fuel rail and fittings ➃
Air intake silencer fit/tightness
Fuel tank straps visual inspection
✔
✔
✔
✔
✔
✔
D
D
D
➇
D
✔
D
D
D
D
O
D
O
D
O
D
D
✔
✔
✔
✔
D
O
Oil injection pump adjustment ➃
✔
✔
D
Oil filter and lines inspection
✔
✔
✔
✔
➇
✔➂
✔
✔
➀
✔
✔
✔
➆
✔
✔
✔
✔
D
✔
✔
✔
D
D
✔
D
✔
D
✔
D
✔
✔
D
✔
✔
Oil filter replacement
Oil reservoir straps
✔
✔➀
D
O
smo2003-005a.book Page 61 Friday, November 1, 2002 8:25 AM
ELECTRICAL
SYSTEM
STEERING
SYSTEM
Inspection and cable adjustment
Drive shaft boot and spline condition
Drive shaft protection hose inspection
PTO flywheel and seal carrier lubrication
(if so equipped)
Shifter system/cable adjustment
Jet pump reservoir oil level/oil condition
Jet pump cover pusher inspection
Impeller shaft seal replacement
Impeller condition and impeller/wear ring clearance
Water intake grate condition
HULL AND
BODY
Electrical connections condition and fastening
(ignition system, electrical box(es), starting system,
fuel injectors, etc.)
MPEM mounting brackets/fasteners
Digitally Encoded Security System
Monitoring beeper
Battery condition and strap(s)
PROPULSION
SYSTEM
EVERY 25
HOURS OR
3 MONTHS
EVERY 50
HOURS OR
6 MONTHS
EVERY 100
HOURS
OR 1 YEAR
TO BE
PERFORMED
BY
DESCRIPTION
FIRST 10
HOURS
FREQUENCY
✔
✔
D
✔
✔
✔
✔
✔
✔
D
D
D
D
✔
✔
D
✔➁
✔➁
D
D
✔
✔
✔
✔
Replace
✔
O
✔
✔
➅
D
D
D
D
D
O
Replace
✔➁
✔➁
Bailer pick-ups, check for obstructions
✔
✔
O
Hull condition
✔
✔
O
NOTE: Some items are included in the PRE-OPERATION CHECKS and not necessarily repeated in this chart.
D: Dealer
O: Operator
➀ Every 10 hours in salt water use.
➁ These items have to be initially checked after 25 hours. Thereafter, servicing
to be made as specified in this chart.
➂ Daily flushing in salt water or foul water use.
➃ Emission-related component.
➄ In salt water use.
➅ Replace at 150 hours.
➆ Replace at 250 hours.
➇ Check at 350 hours or 5 years.
61
smo2003-005a.book Page 62 Friday, November 1, 2002 8:25 AM
Throttle Cable Inspection
Steering Alignment
Depress and release the throttle lever.
It should operate smoothly and return
to its initial position without any hesitation. Refer to an authorized SEA-DOO
dealer if necessary.
WARNING
When the handlebar is directed in
straight ahead position, the jet pump
nozzle should be in the same direction
allowing the watercraft to run in a straight
line.
Refer to an authorized SEA-DOO dealer if an adjustment is necessary.
Do not alter or tamper with throttle cable adjustment or routing.
WARNING
WARNING
Ensure the handlebar and jet pump
nozzle operate freely from side to
side and are not stressing the steering cable or brackets.
If throttle lever does not automatically return, do not operate watercraft and see your authorized
SEA-DOO dealer.
1
Vacuum Bailer Pick-Ups
They are located each side of the drive
shaft tunnel.
Two pick-ups use a low pressure area in
the jet pump to siphon the water out of
the bilge when the engine is operating.
Inspect each pick-up screen for obstructions, clean as necessary.
F01K01Y
1. Should move freely
Fuel Injection System
The fuel injection system inspection
should be performed by an authorized
SEA-DOO dealer.
CAUTION: Never use injector cleaning products. They may contain additives that could damage injector
components.
Fuel and Oil Filters
The fuel filter and the oil filter should be
replaced by an authorized SEA-DOO
dealer. Fuel system pressurization
should be conducted at the same time.
CAUTION: An obstructed oil filter
will cause oil starvation resulting in
serious engine damage.
62
F01L7RY
1
TYPICAL
1. Vacuum bailer pick-ups
smo2003-005a.book Page 63 Friday, November 1, 2002 8:25 AM
Fuses
If an electrical problem occurs, check
the fuses. If a fuse is burnt, replace by
one of the same rating. Follow procedures below.
WARNING
Do not use a higher rated fuse as
this can cause severe damage. If
a fuse has burnt out, source of malfunction should be determined
and corrected before restarting.
See an authorized SEA-DOO dealer for servicing.
Fuses can be found at 2 locations; on
the MPEM and in the rear electrical box.
1
F06H1TY
2
1. Fuse cover
2. Fuse tabs
Rear Electrical Box
Remove seat.
MPEM
To access fuses on the MPEM, open
front storage compartment cover and
remove storage basket.
Locate MPEM on the left side of watercraft.
Remove fuse cover from the MPEM.
1
F07H07Z
TYPICAL
Unclip and remove cover of the electrical box.
F06H1SY
2
TYPICAL
1. MPEM
2. Fuse cover
Use the tabs of the fuse cover to remove
and reinstall fuses.
F12H02Y
1
TYPICAL
1. Fuse holder
Properly reinstall removed components.
63
smo2003-005a.book Page 64 Friday, November 1, 2002 8:25 AM
General Inspection and
Cleaning
Inspection
Check engine compartment for any damage and fuel/oil injection systems for
leaks. Ensure all hose clamps are properly secured and no hose is cracked, kinked
or presenting any other damage.
WARNING
If any gasoline leak and/or odor are
present, do not start the engine.
Have the watercraft serviced by an
authorized SEA-DOO dealer.
Inspect muffler, battery, fuel tank and
oil reservoir fastening devices. Visually
check electrical connections for corrosion and tightness.
Inspect hull and jet pump water intake
grate for damage. Replace or have damaged parts repaired.
WARNING
Periodically verify the seat lock pin
and tighten if needed. Make sure
seat securely latches.
64
Cleaning
The bilge should be cleaned by an authorized SEA-DO dealer to remove any
fuel/oil/electrolyte deposits and mildew.
Occasionally, wash the body with water and soap (only use mild detergent).
Remove any marine organisms from
engine and/or hull. Apply non-abrasive
wax such as silicone wax.
CAUTION: Never clean fiberglass and
plastic parts with strong detergent,
degreasing agent, paint thinner, acetone, etc.
Stains may be removed from seat and
fiberglass with Knight’s Spray-Nine
from Korkay System Ltd or the equivalent.
Respect the environment by ensuring
fuel, oil or cleaning solutions do not
drain into the waterways.
smo2003-005a.book Page 65 Friday, November 1, 2002 8:25 AM
TRAILERING, STORAGE
AND PRE-SEASON PREPARATION
Trailering
Make sure that oil reservoir and fuel
tank caps are properly installed.
WARNING
Never tip this vehicle on end for
transporting. We recommend that
you carry the vehicle in its normal
operating position.
Check the applicable laws and regulations in your area concerning towing a
trailer, especially the following rules:
– brake system
– tow vehicle weight
– mirrors.
Take the following precautions when
towing the watercraft:
Tie the watercraft to both bow and
stern (front/rear) eyelets so that it is
firmly retained on the trailer. Use additional tie-downs if necessary.
CAUTION: Do not route ropes or tiedowns over the seat as they could
produce permanent damage. Wrap
ropes or tie-downs with rags or similar protectors where they can touch
the watercraft body.
Ensure all storage compartment covers and seat are properly latched.
WARNING
Make sure seat is securely latched
before prior to trailering.
A SEA-DOO cover can protect the watercraft, particularly before driving on
dirt roads, to prevent dirt entry through
the air intake opening(s).
Observe trailering safety precautions.
Launching/Loading
CAUTION: Before launching the watercraft, ensure the bilge plugs are
fully screwed. After loading the watercraft, ensure they are removed to
drain bilge.
Storage
WARNING
Because fuel and oil are inflammable, have an authorized SEA-DOO
dealer inspect the fuel and oil systems integrity as specified in the
periodic inspection chart.
It is recommended that the watercraft
be serviced by an authorized SEA-DOO
dealer for storage but the following operations can be performed by you with
a minimum of tools.
CAUTION: Do not run the engine during the storage period.
Engine Draining
Check engine drain hose (lowest hose
of engine). Make sure there is no sand
or other particles in it and that it is not
obstructed so that water can exit the
engine. Clean hose and fitting as necessary.
CAUTION: Water in engine drain hose
should be free to flow out, otherwise
water could be trapped in engine.
Should water freeze in engine, severe damage will occur. Check engine drain hose for obstructions.
Disconnect the quick connect fitting.
Press both tabs and pull fitting.
65
smo2003-005a.book Page 66 Friday, November 1, 2002 8:25 AM
Fuel System
SEA-DOO fuel stabilizer (or equivalent), can be added in fuel tank to prevent fuel deterioration. Follow manufacturer’s instructions for proper use.
CAUTION: Fuel stabilizer should be
added prior to engine lubrication to
ensure fuel system components protection against varnish deposits.
WARNING
F07E0HY
DISCONNECT THIS HOSE
Lower hose as necessary so that draining can take place.
Reconnect fitting when done.
Also ensure air compressor drain line
is not obstructed. Clean as necessary.
Body Rinsing/Repair
Wash the body with soap and water solution (only use mild detergent). Rinse
thoroughly with fresh water. Remove
marine organisms from the hull.
CAUTION: Never clean fiberglass and
plastic parts with strong detergent,
degreasing agent, paint thinner, acetone, etc.
For small gelcoat repairs, refer to an authorized SEA-DOO dealer. Replace damaged labels/decals.
Propulsion System
Lubricant in jet pump reservoir should
be drained and reservoir cleaned. Refer to an authorized SEA-DOO dealer
for this operation.
Grease lubrication point(s) of propulsion
system as explained in MAINTENANCE
section.
66
Fuel is inflammable and explosive
under certain conditions. Always
work in a well ventilated area. Do
not smoke or allow open flames or
sparks in the vicinity. Fuel tank may
be pressurized, slowly turn cap
when opening. Never use an open
flame to check fuel level. When fueling, keep watercraft level. Do not
overfill or top off the fuel tank and
leave watercraft in the sun. As temperature increases, fuel expands
and might overflow. Always wipe
any fuel spillage from the watercraft.
Cooling System Flushing and
Engine Internal Lubrication
Refer to procedure in POST-OPERATION
CARE.
Battery
Contact your authorized SEA-DOO
dealer.
Antifreezing Protection
NOTE: This procedure requires approximately 2.5 L (2.6 U.S. qt.) of antifreeze.
In cool regions where freezing point
may be encountered, cooling system
should be filled with an equal part of
water and antifreeze solution.
smo2003-005a.book Page 67 Friday, November 1, 2002 8:25 AM
CAUTION: Antifreeze mix must be
fed in cooling system. Otherwise remaining water will freeze. This operation requires a good technical
knowledge of the cooling system
path. If antifreezing is not performed
adequately engine/exhaust system
may freeze and cause severe engine
damage. We strongly recommend
this operation be performed by an
authorized SEA-DOO dealer.
CAUTION: Always use ethylene glycol antifreeze containing corrosion
inhibitors specifically recommended
for aluminum engines.
NOTE: When available, it is recommended to use biodegradable antifreeze compatible with internal combustion aluminum engines. This will
contribute to protect the environment.
NOTE: The engine will not have to run
during this operation but should have
been ran before, to exhaust as much
water as possible, from cooling system components.
NOTE: On some models, it may be
easier to reach hoses when you remove the seat opening bridge.
Install hose pinchers at the following
location:
1
F07E0NZ
TYPICAL
1. Water outlet hose
F12E0AY
1
1. Crankcase cooling cover outlet hose
F15L03Y
1
1. Seat opening bridge
Hose Pinchers Installation
Some hoses have to be plugged to
prevent draining, before filling cooling
system jackets with the antifreeze.
F07E0JY
1
1. Engine cylinder drain hose
67
smo2003-005a.book Page 68 Friday, November 1, 2002 8:25 AM
Hose Disconnection
Disconnect water INLET hose at engine
between T-fitting and cylinder head fitting.
F12E0BY
1
1. Disconnect this side of the T-fitting
Temporarily install a short piece of hose
to replace the one removed.
1
F07E0OY
1. Bleed outlet hose
Continue to pour until antifreeze flows
in air compressor water outlet hose.
Antifreeze
Insert a funnel into the temporary hose
and pour antifreeze mix in engine until
the colored solution appears at cooling
system bleed outlet.
F07E0NX
1
1. Air compressor water outlet hose
F07E0LY
At this point, install a hose pincher on
bleed outlet hose.
68
Remove pinchers in this order to allow
proper flow of antifreeze.
1. Bleed outlet hose.
2. Crankcase cooling cover outlet hose.
3. Engine cylinder drain hose.
4. Water outlet hose.
smo2003-005a.book Page 69 Friday, November 1, 2002 8:25 AM
Pour approximately 200 mL (7 oz) of
antifreeze in the water regulator valve
supply hose to allow antifreeze flowing through the valve and into muffler
to protect it.
Remove temporary hose and reconnect engine water outlet hose.
Most of the antifreeze will drain out
when removing the hose pinchers. Use
a container to recover it. DISPOSE ANTIFREEZE AS PER YOUR LOCAL LAWS
AND REGULATIONS.
NOTE: Although antifreeze will mainly
drain out, the antifreeze has mixed with
the water that was possibly trapped in
the water jackets and thus preventing
freezing problems.
At pre-season preparation, drain the remaining antifreeze from cooling system prior to using the watercraft.
The following steps should be performed to provide the watercraft enhanced protection.
Clean the bilge with hot water and detergent or with bilge cleaner. Rinse
thoroughly. Lift front end of watercraft
to completely drain bilge. If any repairs
are needed to body or to the hull contact your authorized SEA-DOO dealer.
For paint touch up to mechanical parts
use Bombardier spray paint.
Reinstall vent tube support (if applicable).
Anticorrosion Treatment
Wipe off any residual water in the engine compartment.
Spray BOMBARDIER LUBE lubricant
or equivalent over metallic components in engine compartment.
WARNING
Do not lubricate the safety lanyard
post.
Final Steps
Apply a good quality marine wax to the
body.
The seat and the seat extension (if so
equipped) should be partially left
opened, the rear access cover and storage baskets (if so equipped) should
be removed during storage. This will
avoid engine compartment condensation and possible corrosion.
If the watercraft is to be stored outside, cover it with an opaque tarpaulin
to prevent sun rays and grime from affecting the plastic components, watercraft finish as well as preventing dust
accumulation.
CAUTION: The watercraft should
never be left in water for storage.
Never leave the watercraft stored in
direct sunlight.
Pre-Season Preparation
Use the following chart.
Since technical skills and special tools
are required, some operations should be
performed by an authorized SEA-DOO
dealer.
WARNING
Only perform procedures as detailed in this guide. It is recommended that the assistance of an authorized SEA-DOO dealer be periodically obtained on other components/
systems not covered in this guide.
Unless otherwise specified, engine
must not be running and the safety lanyard must be removed from
its post for all maintenance procedures. Components inside engine
compartment may be hot. When
component conditions seem less
than satisfactory, replace with genuine BOMBARDIER parts or approved equivalents.
Lubricate the throttle cable with BOMBARDIER LUBE lubricant or equivalent.
69
smo2003-005a.book Page 70 Friday, November 1, 2002 8:25 AM
Pre-Season Preparation Chart
NOTE: It is highly recommended that an authorized SEA-DOO dealer perform
the annual safety inspection and factory campaigns in addition to the pre-season
preparation all at the same time.
OPERATIONS
GENERAL
ENGINE
COOLING SYSTEM
FUEL SYSTEM
Lubrication/corrosion protection
TO BE
PERFORMED
BY
Operator
Spark plug replacement ➀
Dealer
Exhaust system condition (fasteners, hoses etc.)
Dealer
RAVE valve cleaning
Dealer
Counterbalance shaft oil level
Dealer
TDC setting
Dealer
Air compressor, visual condition of hoses. Check for leaks
CAUTION: Main hose between compressor and fuel rail may
be hot.
Dealer
Inspection of cooling system hoses and components
Dealer
Throttle ➁ cable inspection/adjustment
Dealer
Fuel filter replacement
Dealer
Fuel injection sensors verification
Dealer
Fuel system; check valves, lines, fasteners, pressurization ➁
Dealer
Direct injector, check for leakage
Dealer
Filler neck, fuel tank and fuel cap condition ➁
Fuel tank straps
Dealer
Operator
Refill fuel tank
LUBRICATION
SYSTEM
Oil injection pump adjustment and bleeding
Dealer
Oil filter replacement
Dealer
Oil injection reservoir straps
Operator
Oil injection reservoir filling
Operator
Battery condition/charging and reinstallation
ELECTRICAL
SYSTEM
Dealer
Monitoring beeper
Dealer
Digitally encoded security system
Dealer
STEERING SYSTEM Steering system adjustment/inspection ➁
PROPULSION
SYSTEM
HULL AND BODY
Dealer
Battery, starter connections and routing ➁
Dealer
Shifter system condition and cable adjustment
Dealer
Propulsion system inspection
Dealer
Jet pump oil replacement
Dealer
Inspection of bailer pick-ups
Dealer
➀ Before installing new spark plugs, it is suggested to burn the excess BOMBARDIER
LUBE lubricant or equivalent by starting the engine using the old spark plugs.
➁ Safety item covered in the annual safety inspection.
70
smo2003-005a.book Page 71 Friday, November 1, 2002 8:25 AM
TROUBLESHOOTING
The following chart is provided to help in diagnosing the probable source of simple
troubles. You may be able to solve many of these problems rather quickly, but
others may require the skills of a mechanical technician. In such cases, consult
an authorized SEA-DOO dealer for servicing.
Monitoring Beeper Coded Signals
CODED SIGNALS
2 short beeps
(while installing safety
lanyard on post).
POSSIBLE CAUSE
REMEDY
• Confirms safety lanyard signal Engine can be started.
operation.
• Safety lanyard on post for more
1 long beep
than 10 minutes without start(while installing safety
ing engine.
lanyard on watercraft post or
when pressing engine
• Bad connection.
start/stop button).
Apply a slight pressure or remove
and reinstall safety lanyard on post.
Reinstall safety lanyard cap correctly over post.
• Wrong safety lanyard.
Use a safety lanyard that has been
programmed for the watercraft.
• Defective safety lanyard.
Use another programmed safety
lanyard.
• Dried salt water in safety lanyard Clean safety lanyard cap to remove
cap.
salt water.
• Improper operation of MPEM Refer to an authorized SEA-DOO
or defective wiring harness.
dealer.
1 second beep every second •
intervals.
•
A 2 seconds beep every
2 seconds intervals.
•
A 2 seconds beep every
minute intervals.
•
A 2 seconds beep every
15 minutes intervals.
Continuously beeps.
Engine drowned mode is active. Release throttle to cancel this
mode.
Exhaust system overheat.
See engine OVERHEATING.
Fuel tank level is low.
Refill as soon as possible.
Very low battery voltage.
Refer to an authorized SEA-DOO
dealer.
• Coolant and exhaust gas tem- Refer to an authorized SEA-DOO
perature sensors or TPS
dealer.
(throttle position sensor) or CPS
(crankshaft position sensor)
malfunction.
• MPEM malfunction.
Refer to an authorized SEA-DOO
dealer.
• Oil injection reservoir level is low. Refill.
• Engine overheats.
See engine OVERHEATING.
71
smo2003-005a.book Page 72 Friday, November 1, 2002 8:25 AM
Engine Will Not Start
OTHER OBSERVATION
POSSIBLE CAUSE
Engine does not turn over. • Safety lanyard removed.
• Burnt fuse on MPEM or in rear
electrical box: battery, starting
system, fuel pump.
• Discharged battery.
Engine turns slowly.
Engine turns normally.
REMEDY
Install cap over post.
Check wiring then replace fuse(s).
Refer to an authorized SEA-DOO
dealer.
• Battery connections, corroded or Refer to an authorized SEA-DOO
loose.
dealer.
• Water-flooded engine.
Refer to WATER-FLOODED ENGINE in SPECIAL PROCEDURES.
• Faulty sensor or MPEM.
Refer to an authorized SEA-DOO
dealer.
• Seized engine.
Refer to an authorized SEA-DOO
dealer.
• Seized jet pump.
Try to clean. Otherwise, refer to an
authorized SEA-DOO dealer.
• Loose battery cable connections. Check/clean/tighten.
• Discharged or weak battery.
Refer to an authorized SEA-DOO
dealer.
• Worn starter.
Refer to an authorized SEA-DOO
dealer.
• Fuel tank empty or watercontaminated.
• Fouled/defective spark plugs.
Refill. Siphon and fill with fresh fuel.
• Electrical problem.
Refer to an authorized SEA-DOO
dealer.
Replace.
• Faulty component in the fuel in- Refer to an authorized SEA-DOO
jection system.
dealer.
• Burnt fuel pump fuse.
Check wiring then replace fuse.
Engine Misfires, Runs Irregularly
OTHER OBSERVATION
Weak spark.
POSSIBLE CAUSE
• Fouled/defective/worn spark
plugs.
• Faulty MPEM.
• Too much oil supplied to engine.
Lean fuel mixture.
• Fuel: Level too low, stale or
water-contaminated.
• Clogged injectors.
• Defective sensor or MPEM.
Rich fuel mixture
(high fuel consumption).
72
• Flame arrester dirty/clogged
(if so equipped).
• Defective sensor or MPEM.
REMEDY
Replace.
Refer to an authorized SEA-DOO
dealer.
Improper oil pump adjustment,
refer to an authorized SEA-DOO
dealer.
Siphon and/or refill.
Refer to an authorized SEA-DOO
dealer.
Refer to an authorized SEA-DOO
dealer.
Clean or replace.
Refer to an authorized SEA-DOO
dealer.
smo2003-005a.book Page 73 Friday, November 1, 2002 8:25 AM
Engine Overheats
OTHER OBSERVATION
Monitoring beeper
sounds continuously.
POSSIBLE CAUSE
• Clogged jet pump water intake.
REMEDY
Clean.
• Clogged coolant system.
Flush cooling system.
Engine Continually Backfires
OTHER OBSERVATION
Weak spark.
Overheated engine.
POSSIBLE CAUSE
• Fouled/defective/worn spark
plugs.
• See engine OVERHEATS.
• Spark plug leads or wiring reversed.
REMEDY
Replace.
Refer to an authorized SEA-DOO
dealer.
Connect spark plug cables at their
proper location. Otherwise, refer
to an authorized SEA-DOO dealer.
Engine Pinging or Knocking
OTHER OBSERVATION
POSSIBLE CAUSE
• Poor quality gasoline/low octane.
• Spark plug heat range too high.
• Ignition timing or TDC setting.
REMEDY
Use well known quality and recommended gasoline.
Use recommended spark plugs.
Refer to an authorized SEA-DOO
dealer.
Engine Lacks Acceleration or Power
OTHER OBSERVATION
POSSIBLE CAUSE
• Weak spark.
REMEDY
Refer to engine MISFIRES, RUNS
IRREGULARLY.
• Water in fuel or injection oil.
Siphon and replace.
• Clogged injectors.
Refer to an authorized SEA-DOO
dealer.
• Low fuel pressure.
Refer to an authorized SEA-DOO
dealer.
• Stuck RAVE valves.
Refer to an authorized SEA-DOO
dealer.
Overheated engine.
See engine OVERHEATS.
Watercraft Engine Cannot Run Above Idle Speed
OTHER OBSERVATION
POSSIBLE CAUSE
• The monitoring system put the
watercraft in limp home mode
due to a component malfunction.
REMEDY
Try removing and reinstalling the
safety lanyard on its post. Refer
to an authorized SEA-DOO dealer.
73
smo2003-005a.book Page 74 Friday, November 1, 2002 8:25 AM
Watercraft Can Not Reach Top Speed
OTHER OBSERVATION
Cavitation.
POSSIBLE CAUSE
• Jet pump water intake clogged.
REMEDY
Clean.
• Damaged impeller.
Replace. Refer to an authorized
SEA-DOO dealer.
• The safety lanyard used purposely does not allow watercraft top speed.
• The monitoring system put the
watercraft in limp home mode
due to a component malfunction.
Use a safety lanyard that allows to
reach the top speed.
Release throttle so that engine
returns to idle speed. Refer to an
authorized SEA-DOO dealer.
Abnormal Noise From Propulsion System
OTHER OBSERVATION
Cavitation.
74
POSSIBLE CAUSE
• Weeds or debris jammed
around impeller.
• Damaged impeller shaft or drive
shaft.
REMEDY
Clean and check for damage.
Refer to an authorized SEA-DOO
dealer.
smo2003-005a.book Page 75 Friday, November 1, 2002 8:25 AM
SPECIFICATIONS
ENGINE
LRV DI
Engine type
Induction type
Rotax 947, 2-stroke
Reed valve
Water cooled/water injected with
regulator
Rotax Adjustable Variable Exhaust (RAVE)
Exhaust system
Exhaust valve
Type
Lubrication
Oil type
Number of cylinders
Displacement
Oil injection
BOMBARDIER Formula XP-S
synthetic injection oil (or equivalent)
2
951.2 cm3 (58 in3)
Rev limiter setting
COOLING
7200 ± 50 RPM
Open circuit.
Direct flow from propulsion unit
Type
ELECTRICAL
Magneto generator output
Ignition system type
Spark plug
Make and type
Gap
Starting system
Battery
Fuse
270 W @ 6000 RPM
Digital inductive type
NGK, ZFR4F
1.1 mm (.043 in)
Electric starter with reduction gear
12 V, 19 A•h
Battery
Main
25 A
30 A
MPEM
Charging system (REG)
N.A.
25 A
Information center
Injection system (INJ)
N.A.
N.A.
Fuel pump (FP)
N.A.
CARBURETION
Fuel type
Fuel injection
Unleaded regular gasoline with 87
minimum octane (R+M)/2
Orbital direct fuel injection,
twin throttle body (46 mm (1.81 in))
N.A.: Not Applicable.
75
smo2003-005a.book Page 76 Friday, November 1, 2002 8:25 AM
PROPULSION
Propulsion system
LRV DI
Bombardier Formula pump
Jet pump type
Transmission
Axial flow, single stage
Direct drive
Reverse system
Yes
SEA-DOO synthetic polyolester oil
SAE 75W90 GL5
Jet pump oil type
Pivoting angle of direction (nozzle)
Minimum required water level for jet pump
DIMENSIONS
Number of passengers ➀
~ 23°
90 cm (3 ft)
4
Overall length
Overall width
396 cm (156 in)
155 cm (61 in)
Overall height
Weight
108 cm (42.5 in)
432 kg (952 lb)
Load limit (passengers + luggage)
CAPACITIES
Fuel tank
Oil injection tank
Impeller shaft
reservoir
338 kg (745 lb)
95 L (25 U.S. gal)
6 L (1.6 U.S. gal)
Capacity
Oil level
115 mL (3.9 U.S. oz)
Up to plug
➀ Refer to load limit.
BOMBARDIER INC. reserves the right to make changes in design and specifications and/or to make additions to, or improvements in its products without imposing any obligation upon itself to install them on its products previously manufactured.
76
smo2003-005a.book Page 77 Friday, November 1, 2002 8:25 AM
SI* METRIC INFORMATION
BASE UNITS
DESCRIPTION
length..................................................
mass ...................................................
force....................................................
liquid ...................................................
temperature ........................................
pressure..............................................
torque .................................................
land velocity ........................................
navigation velocity...............................
UNIT
meter .................................
kilogram .............................
newton...............................
liter .....................................
Celsius ...............................
kilopascal............................
newton-meter ....................
kilometer per hour..............
knot ....................................
SYMBOL
m
kg
N
L
°C
kPa
N•m
km/h
kn
PREFIXES
PREFIX
kilo .......................
centi .....................
milli.......................
micro....................
SYMBOL
k ........................
c ........................
m .......................
µ ........................
MEANING
one thousand .....................
one hundredth of ...............
one thousandth of..............
one millionth of ..................
VALUE
1000
0.01
0.001
0.000001
CONVERSION FACTORS
TO CONVERT
in .........................................................
in .........................................................
in²........................................................
in³........................................................
ft .........................................................
oz ........................................................
lb .........................................................
lbf........................................................
lbf•in...................................................
lbf•ft....................................................
lbf•ft....................................................
PSI ......................................................
imp. oz ................................................
imp. oz ................................................
imp. gal ...............................................
imp. gal ...............................................
U.S. oz.................................................
U.S. gal................................................
knot .....................................................
MPH....................................................
Fahrenheit ...........................................
Celsius ................................................
hp........................................................
TO ➀
mm.....................................
cm ......................................
cm².....................................
cm³.....................................
m........................................
g .........................................
kg .......................................
N ........................................
N•m ...................................
N•m ...................................
lbf•in..................................
kPa .....................................
U.S. oz................................
mL......................................
U.S. gal...............................
L .........................................
mL......................................
L .........................................
MPH...................................
km/h ...................................
Celsius ...............................
Fahrenheit ..........................
kW......................................
MULTIPLY BY
25.4
2.54
6.45
16.39
0.3
28.35
0.45
4.4
0.11
1.36
12
6.89
0.96
28.41
1.2
4.55
29.57
3.79
1.15
1.61
(°F - 32) ÷ 1.8
(°C x 1.8) + 32
.75
* The international system of units abbreviates SI in all languages.
➀ To obtain the reverse sequence, divide by the given factor. Example: to convert
millimeters to inches, divide by 25.4.
NOTE: Conversion factors are rounded off to 2 decimals for easier use.
77
smo2003-005a.book Page 78 Friday, November 1, 2002 8:25 AM
ABBREVIATIONS USED IN THIS MANUAL
DESCRIPTION
AC
CDI
Alternate current
Capacitor discharge ignition
DC
DESS
Direct current
Digitally encoded security
system
DI
ECU
Direct injection
Electronic control unit
E.I.N.
EPA
Engine identification number
Environmental protection
agency
HP
LCD
Horse power
Liquid crystal display
LED
MAG
Light-emitting diode
Magneto
MPEM Multi-purpose electronic module
MPH
Mile per hour
N.A.
OPT
Not applicable
Optional
PFD
P/N
Personal flotation device
Part number
PTO
RAVE
Power take off
Rotax adjustable variable
exhaust
STD
TBD
Standard
To be determined
TDC
VROI
Top dead center
Variable rate oil injection
78
smo2003-005a.book Page 79 Friday, November 1, 2002 8:25 AM
PRIVACY INFORMATION
We wish to inform you that your coordinates will be used for safety and warranty
purposes. Sometimes, we also use the coordinates of our clients to inform them
about our products and to present them offers. Should you prefer not to receive
information on our products, services and offers, please let us know by writing
to the address below.
Also note that, from time to time, carefully selected and trustworthy organizations
may be permitted to use the coordinates of our clients to promote quality products and services. If you prefer not to have your name and address released,
please let us know by writing to the address below:
BOMBARDIER INC.
RECREATIONAL PRODUCTS
WARRANTY DEPARTMENT
75, J.A. BOMBARDIER STREET
SHERBROOKE, QUÉBEC
CANADA J1L 1W3
FAX NUMBER (819) 566-3590
79
smo2003-005a.book Page 80 Friday, November 1, 2002 8:25 AM
smo2003-005a.book Page 81 Friday, November 1, 2002 8:25 AM
CHANGE OF ADDRESS
If your address has changed, be sure to fill out and mail the card provided on this
page.
Such notification is likewise necessary for your own safety even after expiration
of the original warranty, since Bombardier will be in a position to contact you if
correction to your watercraft becomes necessary.
NOTE: This card is strictly for change of address only.
CHANGE OF ADDRESS
✃
CHANGE OF ADDRESS
❏
WATERCRAFT IDENTIFICATION NUMBERS
Model Number
Hull Identification Number (H.I.N.)
OLD ADDRESS: ______________________________________________
NAME
________________________________________________________________
NO.
STREET
APT
________________________________________________________________
CITY
STATE/PROVINCE
ZIP/POSTAL CODE
NEW ADDRESS: ______________________________________________
NAME
________________________________________________________________
NO.
STREET
APT
________________________________________________________________
CITY
STATE/PROVINCE
ZIP/POSTAL CODE
STOLEN UNITS
In the event that your watercraft is stolen, you should notify your area’s distributor
warranty department of such.
Please provide your name, address, phone number, Hull Identification Number and
date it was stolen.
Bombardier will provide a list of stolen units to all authorized Sea-Doo dealers on a
monthly basis to aid in recovery of such units to their owners.
81
smo2003-005a.book Page 82 Friday, November 1, 2002 8:25 AM
CHANGE OF ADDRESS
If your address has changed, be sure to fill out and mail the card provided on this
page.
Such notification is likewise necessary for your own safety even after expiration
of the original warranty, since Bombardier will be in a position to contact you if
correction to your watercraft becomes necessary.
NOTE: This card is strictly for change of address only.
CHANGE OF ADDRESS
✁
AFFIX
PROPER
POSTAGE
BOMBARDIER
RECREATIONAL PRODUCTS
WARRANTY DEPARTMENT
75, J.A. BOMBARDIER ST.
SHERBROOKE (QUEBEC)
CANADA J1L 1W3
smo2003-005a.book Page 83 Friday, November 1, 2002 8:25 AM
CHANGE OF ADDRESS
If your address has changed, be sure to fill out and mail the card provided on this
page.
Such notification is likewise necessary for your own safety even after expiration
of the original warranty, since Bombardier will be in a position to contact you if
correction to your watercraft becomes necessary.
NOTE: This card is strictly for change of address only.
CHANGE OF ADDRESS
✃
CHANGE OF ADDRESS
❏
WATERCRAFT IDENTIFICATION NUMBERS
Model Number
Hull Identification Number (H.I.N.)
OLD ADDRESS: ______________________________________________
NAME
________________________________________________________________
NO.
STREET
APT
________________________________________________________________
CITY
STATE/PROVINCE
ZIP/POSTAL CODE
NEW ADDRESS: ______________________________________________
NAME
________________________________________________________________
NO.
STREET
APT
________________________________________________________________
CITY
STATE/PROVINCE
ZIP/POSTAL CODE
STOLEN UNITS
In the event that your watercraft is stolen, you should notify your area’s distributor
warranty department of such.
Please provide your name, address, phone number, Hull Identification Number and
date it was stolen.
Bombardier will provide a list of stolen units to all authorized Sea-Doo dealers on a
monthly basis to aid in recovery of such units to their owners.
83
smo2003-005a.book Page 84 Friday, November 1, 2002 8:25 AM
CHANGE OF ADDRESS
If your address has changed, be sure to fill out and mail the card provided on this
page.
Such notification is likewise necessary for your own safety even after expiration
of the original warranty, since Bombardier will be in a position to contact you if
correction to your watercraft becomes necessary.
NOTE: This card is strictly for change of address only.
CHANGE OF ADDRESS
✁
AFFIX
PROPER
POSTAGE
BOMBARDIER
RECREATIONAL PRODUCTS
WARRANTY DEPARTMENT
75, J.A. BOMBARDIER ST.
SHERBROOKE (QUEBEC)
CANADA J1L 1W3
smo2003-005a.book Page 85 Friday, November 1, 2002 8:25 AM
WATERCRAFT MODEL No.
HULL
IDENTIFICATION NUMBER (H.I.N.)
ENGINE
IDENTIFICATION NUMBER (E.I.N.)
Owner:
NAME
No.
CITY
STREET
APT
STATE/PROVINCE
ZIP/POSTAL CODE
Purchase Date
YEAR
MONTH
DAY
YEAR
MONTH
DAY
Warranty Expiry Date
To be completed by the authorized Sea-Doo dealer at the time of the sale.
DEALER IMPRINT AREA
Please verify with your selling dealer to ensure your SEA-DOO watercraft
has been registered with Bombardier.
Download PDF

advertising