MARTECH RCD PRO
User Manual v1.4
MARTECH RCD PRO
List of contents:
1. Basic informations about product .................................................................. 3
1.1 Models supported by RCD PRO (CLIP version) .................................................................................. 3
1.2 Models supported by RCD PRO PC (PC computer application) ........................................................ 3
2. Main functions and possibilites of each module ........................................... 4
2.1 For radios RCD 210 CQ-JV1871G by Matsushita ................................................................................ 4
2.2 For radios RCD 310 / 510 / Seat Ultra Low 250BVX / Skoda Swing................................................... 5
2.3 For radios RCD 500 CQ-EV1572 by Matsushita .................................................................................. 6
2.4 For radios RNS 510 (Siemens / VDO, Continental, Columbus) ........................................................... 6
2.5 For radios RNS 315 EU by Technisat ..................................................................................................... 7
2.6 For radios Navi Dresden 1 by Technisat ................................................................................................ 8
2.7 For radios GAMMA 3 by Philips ............................................................................................................ 9
3. Main functions and possibilites of PC modules .......................................... 10
4. Hardware requirements ................................................................................ 11
4.1 Technical Support activation................................................................................................................. 11
5. Working conditions........................................................................................ 12
6. Working with RCD PRO based on CLIP.................................................... 13
6.1 RCDPRO_RCD210 ................................................................................................................................ 13
6.1.2 Algorithm for reading code from RCD210 series ............................................................................. 13
6.1.3 Diagram connection scheme for RCD210 ......................................................................................... 14
6.2 RCDPRO_RCD310 ................................................................................................................................ 19
6.2.1 Diagram connection scheme for RCD310 / Skoda Swing ................................................................ 20
6.2.2 Diagram connection scheme for Seat Ultra Low MP3 250BVX ..................................................... 23
6.2.3 Diagram connection scheme for RCD510 ......................................................................................... 25
6.2.4 RCDPRO_RCD310_v14 module functions ....................................................................................... 27
6.2.5 Algorithm for reading code from car / navi RCD310, 250BVX, RCD510 ..................................... 29
6.3 RCDPRO_RCD500 ................................................................................................................................ 30
6.3.1 Wiring diagram for RCD500 .............................................................................................................. 30
6.3.2 RCDPRO_RCD500_v10 module functions ....................................................................................... 32
6.3.3 Algorithm for reading code from car / navi RCD500 ...................................................................... 33
6.4 RCDPRO_RNS510 ................................................................................................................................. 34
6.4.1 Diagram connection scheme for RNS510 .......................................................................................... 34
6.4.2 RCDPRO_RNS510 module functions................................................................................................ 35
6.4.3 Algorithm for reading code from car / navi RNS510 ....................................................................... 36
6.4.4 Algorithm for TV-Free – Video in Motion activation ...................................................................... 36
6.5 RCDPRO_RNS315 (version 1.2 and up) .............................................................................................. 38
6.5.1 Expander modification for RNS 315.................................................................................................. 39
6.5.2 Diagram connection scheme for RNS 315 ......................................................................................... 42
6.5.3 Algorithm for reading code from car / navi RNS315 ....................................................................... 44
6.6 RCDPRO_TechniSat.............................................................................................................................. 48
6.6.1 Expander EPMv1.0 modifications for Navi Dresden ....................................................................... 48
6.6.2 Diagram connection scheme for Navi Dresden ................................................................................. 49
6.6.3 Algorithm for code reading from Navi Dresden ............................................................................... 52
6.7 RCDPRO_GAMMA3............................................................................................................................. 54
6.7.1 Diagram connection scheme for GAMMA3...................................................................................... 55
6.7.2 RCDPRO_GAMMA3 module functions ........................................................................................... 59
6.7.3 Algorithm for reading code from GAMMA3 ................................................................................... 60
User manual
2
MARTECH RCD PRO
1. Basic informations about product
RCD PRO it's a new project designed for decoding car radios and navigations.
Project consist of standalone tool based on Martech CLIP (RCD PRO) and additional PC computer
application (RCD PRO PC).
Application works "standalone" - this means you can use it totally without PC computer.
Whole unlock modes, read code process, or read / save memory to file is executed on Martech CLIP
device and MMC card as data carrier.
1.1 Models supported by RCD PRO (CLIP version)
The most popular models supported via this mode are:
•
•
•
•
•
•
•
RCD 210. RCD 500 by Panasonic
Seat Ultra Low 250 BVX / 359 BVX
RCD 310, Skoda Swing manufactured by Blaupunkt
RCD 510, Skoda Bolero by Blaupunkt
RNS 510, Skoda Columbus produced by Siemens VDO / Continental
RNS 315, Navi Dresden 1 produced by TechniSat
VW Gamma 3 by Philips
1.2 Models supported by RCD PRO PC (PC computer application)
Due to frequent updates and a growing list of models, we suggest to download the current list:
http://martech.pl/download/PINOUTS/RCDPRO_models.pdf
The most popular models supported via this mode are:
•
•
•
•
•
•
•
RNS 510 / Skoda Columbus (code change, part number rep air, logo change, device coding,
service commands)
Kenwood from series: KDC, KRC, KVT, DPX, DDX
RCD 310, Skoda Swing, RCD 510, Bolero manufactured by Delphi
Technisat models like Beat, Dance, Gamma V, RCD 210, ULVWCD
Navigations used in Honda cars: BB712PC, BB714PH
Radios from Alfa Romeo, Fiat, Lancia, Iveco cars
Units produced by Sony for Ford: C307, C214, CD132, CD340
Actual program version you can download from this link:
http://martech.pl/download/RCDPRO/rcdpro.zip
User manual
3
MARTECH RCD PRO
2. Main functions and possibilites of each module
Currently there are following applications based on CLIP:
2.1 For radios RCD 210 CQ-JV1871G by Matsushita
(application for these models: RCDPRO_RCD210_vXX.prg, where XX it’s actual version)
•
•
reading out original radio code
keyboard test mode
User manual
4
MARTECH RCD PRO
2.2 For radios RCD 310 / 510 / Seat Ultra Low 250BVX / Skoda Swing
(application for these models: RCDPRO_BP310_vXX.prg, where XX it’s current version)
•
•
•
•
reading out original radio code (fast and slow mode),
read / write memory, counter reset
reading basic device information
keyboard test mode
User manual
5
MARTECH RCD PRO
2.3 For radios RCD 500 CQ-EV1572 by Matsushita
(application for these models: RCDPRO_RCD500_vXX.prg, where XX it’s current version)
•
•
reading basic device informations
reading out original radio code (Fast, 3 seconds process, directly from device mcu)
2.4 For radios RNS 510 (Siemens / VDO, Continental, Columbus)
(application for these models: RCDPRO_RNS510_vXX.prg (where XX it’s current version)
•
•
•
decoding navigatins (by changing code to specified by user)
TV-Free aka Video In Motion activation
service mode on / off
User manual
6
MARTECH RCD PRO
2.5 For radios RNS 315 EU by Technisat
(application for these models: RCDPRO_RNS315_vXX.prg (where XX it’s current version)
•
•
reading out original radio code
keyboard test mode
User manual
7
MARTECH RCD PRO
2.6 For radios Navi Dresden 1 by Technisat
(application for these models: RCDPRO_TechniSat_vXX.prg (where XX it’s current version)
•
•
reading out original radio code
keyboard test mode
User manual
8
MARTECH RCD PRO
2.7 For radios GAMMA 3 by Philips
(application for these models: RCDPRO_GAMMA3t_vXX.prg (where XX it’s current version)
•
•
•
•
reading basic device informations
read/write eeprom memory
reading out original radio code
power on/off test
User manual
9
MARTECH RCD PRO
3. Main functions and possibilites of PC modules
RCD PRO PC it's special PC computer application, which allows to decode car radios made by using
computer and CLIP as hardware dongle. Main advantage is AutoSearch mode, which is developed for
finding correct code on unsupported models. Application recognizes many new algorithms and then it
looks for all possible codes. Automatic updates, easy and user friendly interface to use.
Main functions:
- reading out radio code
- resetting counter of tries
- changing radio code to specified by user (depends on model, manufacturer)
- generating bin files ready to be programmed In EEPROM memory
- AutoSearch code function for models not on supported list or radios which will be produced in future
You can download application from section RCD PRO Service Tools - Technical Support on
http://martech.pl/forum
User manual
10
MARTECH RCD PRO
4. Hardware requirements
For proper work you will need:
- Martech CLIP device with RCD PRO activation
- PC computer with internet connection (needed for downloading tools and updates)
- in case of using standalone to ols on CLIP, mostly there is necessity to use additional expanders.
Details you can see in discussion of individual applications.
- 12V power supply with 3A current efficiency, including wiring for feeding car stereo / navigations.
4.1 Technical Support activation
As additionally you are getting access to special area with applications, user manuals and connection
diagrams – Technical Support.
Together with buying whole set or just an activation you should give your forum nickname to reseller.
It’s main condition to get access to this special section, designed only for application users.
Direct link: http://martech.pl/forum/viewforum.php?f=35
User manual
11
MARTECH RCD PRO
5. Working conditions
Working with RCD PRO module requires from the user the basic knowledge in electronics and manual
skills, which allow to perform the connections soldered to the PCB boards. For this purpose, there are
necessary tools for assembly, sometimes you will have to use hot air station.
We draw attention to the use of appropriate tools. Keep in mind the danger of the emergence of damage
due to ESD electrostatic charge. Please prepare a work station, to guard against unauthorized intruders.
We take no responsibility for any damage or loss caused by a faulty connection or maintenance of
systems, contrary to their purpose.
User manual
12
MARTECH RCD PRO
6. Working with RCD PRO based on CLIP
6.1 RCDPRO_RCD210
Module designed for radios RCD 210 CQ-JV1871G by Matsushita.
Required equipment:
- Martech CLIP with RCD PRO activation
- Martach CLIP Expander v1.1 with RCD210 module
- 12V/3A power supply to power the radio
6.1.2 Algorithm for reading code from RCD210 series
Functional diagram:
1. Remove the metal shields
2. Desolder 93C76 memory (use hot air stadion)
3. Connect the expander signals with radio pcb according to diagram below
User manual
13
MARTECH RCD PRO
6.1.3 Diagram connection scheme for RCD210
RCD210 module signal connections of RJ45 socket:
Pin 1 connect with pin 1 of CN602 socket
Pin 2 connect with pin 9 of CN602 socket
Pin 3 connect with pin 10 of CN602 socket
Pin 4 connect with pin 2 of CN601 socket
Pin 5 connect with pin 8 of CN602 socket
Pin 6 connect with pin 3 of CN602 socket
Pin 7 connect with GND signal of radio
Pin 8 connect with pin 2 of CN602 socket
CN602/601(CP401/402) slots are located on the TOP side of radio PCB board.
Signal connections of expander RJ45 PORT2 socket
Pin 2 – testpoint RST
Pin 5 – testpoint EPM
Testpoints are located on the BOTTOM side of radio PCB board.
User manual
14
MARTECH RCD PRO
Below - indicated testpoints on the PCB board, pin1 from the left side connectors
User manual
15
MARTECH RCD PRO
RST and EPM testpoint signals
4. Assemble the radio in a way that ensures the proper functioning of the device. Enable it by
connecting 12V previously.
5. Run RCDPRO_RCD210 application on your CLIP
6. Choose “Keyboard Test” function. This function carries out keyboard test, program will ask for
confirmation, select „YES”
User manual
16
MARTECH RCD PRO
From the radio screen appears the code 0592, after a short while will approve the OK button code.
If the test is not correct - check the connection point 3
7. Now you should turn off power supply for 10 seconds, then connect wires again. Radio should
be turned off.
8. Select Find Code – Slow Mode
This function searches for the radio code according to the parameters by the user.
There we have the possibility of search settings in auto mode or manual.
Auto mode searches for code since 0000, while in manual mode you can set your code, from
which the search will take place. For this purpose, press Change and using CLIP keys: UP and
DN, set the appropriate value of the initial code. It should be noted that a single push of a code
increment the value of the unit, and longer holding the key UP or DN will increase in increments
of code 10th.
Hit Start - search process starts.
User manual
17
MARTECH RCD PRO
Finding the code will be confirmed by an appropriate message. It may happen that the system
will identify bad code found. This may be due to voltage fluctuation or even tapped the radio. If
necessary, you can continue to code search by selecting Continue.
9. Unplug the cables and desolder all wires.
10. Now you need to solder back the memory 93C76 paying attention to its correct orientation.
Process completed.
User manual
18
MARTECH RCD PRO
6.2 RCDPRO_RCD310
Module designed to work with radios RCD 310 / 510 / Seat Ultra Low 250BVX / Skoda Swing
Required equipment:
- Martech CLIP with RCD PRO activation
- Martech CLIP Expander v1.1
- 12V/3A power supply to power the radio
Functional diagram:
1. Remove the metal shield from the radio, so as to have easy access to testpoints.
2. Choose the correct Expander configuration:
3. Connect the signals according to schedules set out further below.
User manual
19
MARTECH RCD PRO
6.2.1 Diagram connection scheme for RCD310 / Skoda Swing
User manual
20
MARTECH RCD PRO
RCD310 tespoints (PCB side – bottom)
User manual
21
MARTECH RCD PRO
Connect all the signals except TP1, TP2, TP3, TP4, K2 (RCD510) and 5V.
Remember to connect the GND!
All these pictures at better resolution, please visit http://martech.pl/forum - RCD PRO section.
Remember to connect the radio power supply 12V/3A.
+12V GND
User manual
22
MARTECH RCD PRO
6.2.2 Diagram connection scheme for Seat Ultra Low MP3 250BVX
Seat 250BVX testpoints (PCB side – bottom)
Connect all the signals except TP1, TP2, TP3, TP4, K2 (RCD510) and 5V.
Remember to connect the GND!
All these pictures at better resolution, please visit http://martech.pl/forum - RCD PRO section.
User manual
23
MARTECH RCD PRO
Remember to connect the radio power supply 12V/3A.
Attention!
The code for this model is entered by the use of a Rotary Encoder (Big round button) and if you are
failing to read a code number successfully, then it is important to perform a keyboard test. The purpose
of the test is to ensure that the Clip is able to communicate with the stereo, and its function is to select
and enter an incorrect code, putting the unit into SAFE1 or SAFE2 mode. This can, of course be reset
using the other functions from the Clip menu.
If the test is successful, the Clip will display a series of numbers, ie: 0,1,2,3, OK - DONE and you
should see these numbers being automatically selected and entered onto the radio display at the same
time.
However, if the Clip displays the same numbers above, but nothing happens on the radio, or you see the
blank code entry square moving across the radio screen, then the test has been unsuccessful.
If this is the case, then try turning the Rotary Encoder one click clockwise and then perform the test
again. Repeat by turning the Rotary Encoder one click counter clockwise if still unsuccessful.
If all has failed, then you will need to recheck the solder connections that you have made between the
Expander and the radio.
+12V GND
User manual
24
MARTECH RCD PRO
6.2.3 Diagram connection scheme for RCD510
RCD 510 testpoints (PCB side – bottom)
Connect all the signals except K1, K2, K3 and 5V. Remember about GND signal!
8 pin - K2 (RCD510) must be connected to testpoint marked on the photo as K2.
Additionally, you should connect signals TP1, TP2, TP3 and TP4. It appears on the display board.
Disconnect touch panel flex previously
User manual
25
MARTECH RCD PRO
All these pictures at better resolution, please visit http://martech.pl/forum - RCD PRO section.
Remember to connect the radio power supply 12V/3A.
+12V GND
User manual
26
MARTECH RCD PRO
6.2.4 RCDPRO_RCD310_v14 module functions
Standalone application RCDPRO_RCD310_v14 has following features:
1. Read Info – reads details about the connected navigation
2. Read EEPROM – read the contents of the EEPROM SPI 95128 - thanks to this feature you can
perform a backup of memory.
We recommend that you make a backup before starting the code searching.
3. Write EEPROM – writing the contents of the EEPROM SPI 95128 - re-use previously read out
the contents of EEPROM
4. SAFE2 to SAFE0 Reset – allows to reset counter of tries.
Dual enter the wrong code blocks radio / navigation in time 1h. Calling this function resets the
counter, allowing the inclusion of the code.
User manual
27
MARTECH RCD PRO
5. Find Code – Fast Mode – function to find the code according to the old algorithm.
Applies only to models of radios / navigation with the old firmware.
6. Find Code – Slow Mode – code serach function.
It is the function of retrieving the radio code according to the parameters by the user.
There we have the possibility of search settings in auto mode or manual.
Auto mode searches for the first two digits of the code, the search is therefore limited to
checking up to 100 codes. This accelerates the process of finding the correct code for max 20
minutes time. In the case of a bad eeprom readout, countdown starts at 0000 from.
In manual mode you can set your code, from which the search will take place. For this purpose,
press Change and using CLIP keys: UP and DN, set the appropriate value of the initial code.
It should be noted that a single push of a code increment the value of the unit, and longer holding
the key UP or DN will increase in increments of code 10th.
7. Expander Keyboard Test – this function is checking the correctness of the signals connect the
keyboard section. In addition, in the case of navigation with touch panel, allows you to call
SAFE2.
Properly executed Test will print on the LCD radio / navigation code and approval given him the
OK button. In the case of defective work - please check connections between Expander and radio
/ navigation.
User manual
28
MARTECH RCD PRO
Attention!
SEAT 250BVX is equipped with a universal manipulator. If the keyboard does not pass the test
properly, turn the keypad of a "click" on the right or left. Invoke the keyboard test again to make sure
that the correct configuration.
6.2.5 Algorithm for reading code from car / navi RCD310, 250BVX, RCD510
Functional diagram:
1. Remove the radio metal shields
2. Connect the Expander signals from the radio plate according to the diagram for the radio /
navigation
3. Assemble the radio in a way that ensures the proper functioning of the device.
4. Connect 12V power supply, turn it on
5. Run the application on CLIP
6. Perform Backup EEprom memory, additionally will be checked the connection of EEPROM
memory
7. Perform Keyboard Test, additionally will be checked the keyboard connection
8. Invoke the Find Code - Slow Mode. Be sure to follow the instructions indicated on the CLIP
LCD. If required to turn off the radio for 10 seconds, disconnect the power from the radio this
time, then reconnect power, but do not turn on the radio.
9. Start the process in auto mode, the radio / navigation LCD display will be blinking - this is
normal. In this way, first two digits of code will be calculated to narrow the search to a
maximum of 100 trials.
Search process will start.
If it happens that the search process ends at the first attempt (and the code will be wrong for
example 0499, 1099, 1899), restore the state of the radio / navigation to SAFE0, disconnect
power for 1 minute and follow from step No. 7
If you need to interrupt the process of Slow Mode, hold down the Exit button for about 5
seconds. Interrupting the action of the program in any other way may damage the contents of
EEPROM.
Finding code is signaled by an appropriate message on the LCD CLIP. Write down the code, disconnect
the power supply, desolder expander cables from the radio.
Process Completed.
User manual
29
MARTECH RCD PRO
6.3 RCDPRO_RCD500
Module designed to work with radios RCD 500 CQ-EV1572 by Matsushita
Required equipment:
- Martech CLIP with RCD PRO activation
- 12V/3A power supply to power the radio
6.3.1 Wiring diagram for RCD500
Test points are located on the PCB at the bottom side of the radio.
For the correct operation it requires only: the power connection and radio signals from PORT1 and
PORT2 of the CLIP by the following scheme (pinout is also available from the same application - Help
tab):
PORT1 pin 4 - RST testpoint
PORT1 pin 5 - CNVSS testpoint
PORT2 pin 4 - TXD testpoint
PORT2 pin 5 - RXD testpoint
PORT2 pin 7 - GND testpoint
User manual
30
MARTECH RCD PRO
Remember to connect the radio power supply 12V/3A.
+12V GND
User manual
31
MARTECH RCD PRO
6.3.2 RCDPRO_RCD500_v10 module functions
Standalone RCDPRO_RCD500_v10 application has following features:
- Read Info – reads details about the connected navigation
User manual
32
MARTECH RCD PRO
- Read Code – Reading out original code (fast, 3 seconds process of Reading directly from radio mcu)
- Help – information about pinouts and connections
6.3.3 Algorithm for reading code from car / navi RCD500
Functional diagram:
1. Remove the metal shields of the radio
2. Connect signals from PORT1 and PORT2 with radio pcb, according to above diagram
3. Connect 12V power supply
4. Use Read Info function – addiotnally it will be checked connection of power and transmission
signals.
5. Invoke the function Read Code - the code will be read out and displayed in a few moments
6. Disconnect the power and transmission signals
Process completed.
User manual
33
MARTECH RCD PRO
6.4 RCDPRO_RNS510
Module designed to work with RNS510 (Siemens/VDO, Continental, Columbus) navigations
Required equipment:
- Martech CLIP with RCD PRO activation
- 12V/3A power supply to power the radio
- LTTL to RS232 converter
- cable with 26pin connector for Navi system
6.4.1 Diagram connection scheme for RNS510
LTTL RS232 converter schematic you can find at www.martech.pl/forum. You can make it on the
basis of standard MAX232, also. Power signal can be taken directly from pin1 of RJ45 PORT2 of CLIP.
There is no need to use Martech Expander for these units. In the absence of a plug-for navigation
system, you can use a regular slot with the goldpins in 2.54mm pitch.
User manual
34
MARTECH RCD PRO
Remember to connect the radio power supply 12V/3A.
+12V GND
6.4.2 RCDPRO_RNS510 module functions
RCDPRO_RNS510_v13 has following features:
- Service Mode On – enables service mode. Service mode allows you to edit the code navigation.
Service Mode ON function requires a restart of navigation. This is done by disconnecting the 12V power
supply for a while. After reboot it will goes to service mode.
- Service Mode Off – disabling service mode. Turning this mode will change your navi mode to normal
mode. Requires a restart of navigation. This is done by disconnecting the 12V power supply for a while.
- Set New Navi Code – feature only available in the service mode of navigation.
It allows you to edit the code.
- Enable Video Mode - feature for unlocking possibility of watching video Chile driving.
Does not require the use of the service mode
User manual
35
MARTECH RCD PRO
6.4.3 Algorithm for reading code from car / navi RNS510
Functional diagram:
1. Plug the system in accordance with the model shown above.
2. Connect 12V/3A Power supply to the navigation
3. Use Service Mode On
4. Disconnect and connect +12V power supply - the LCD will display the service mode
5. Use Set New Navi Code function
6. Set up correct code using UP and DN CLIP keys
7. Use Service Mode Off
8. Disconnect and connect +12V power supply
Process completed.
6.4.4 Algorithm for TV-Free – Video in Motion activation
Functional diagram:
1. Plug the system in accordance with the model shown above
2. Connect 12V/3A power supply to the navigation
3. Turn navigation on, be sure it’s in Normal mode (if necessary, use the Service Mode Off)
4. Use Enable Video Mode function
5. Press Start, disconnect the power supply for 2 seconds and then reconnect, then turn on the radio
User manual
36
MARTECH RCD PRO
6. The result of this process is the ability to watch video while driving by passengers
(Note, please be careful!)
User manual
37
MARTECH RCD PRO
6.5 RCDPRO_RNS315 (version 1.2 and up)
Module designed to work with RNS 315 EU TechniSat.
Required equipment:
- Martech CLIP with RCD PRO activation
- SPI_Tool Clip Portable Application version 1.2 and up.
- Martech CLIP Expander v1.1 with RCD210 module
- 12V/3A Power supply (for radio power supply)
Attention!
RNS 315 requires Expander v1.1 modification. Below you will find details.
User manual
38
MARTECH RCD PRO
6.5.1 Expander modification for RNS 315
Expander TOP side. New resistors values.
Values are shown in Ohms. Resistors package size is 0806.
Note! The following modification can be used also for other models which are supported
by the RCDPRO application. Cutting path does not affect on the work of the other applications.
User manual
39
MARTECH RCD PRO
Expander TOP side. Switch power to 3.3V, an additional path must be cut out in the marked location.
User manual
40
MARTECH RCD PRO
Expander Bottom side. Perform the selected connection. The selected resistor should have a value of 0
ohm (short circuit). U10 and U11 signals should be connected to test points located on front panel pcb.
Note! The following modification can be used also for other models which are supported
by the RCDPRO application. Cutting path does not affect for the work of the other applications.
High resolution photos are available under suport area.
User manual
41
MARTECH RCD PRO
6.5.2 Diagram connection scheme for RNS 315
You will need to connect signals to front panel pcb and to the radio motherboard (bottom side)
Below - indicated test points on the radio motherboard. In addition, a voltage divider must be soldered
as below.
For example: R2.2, means second pin of RJ45 expander socket, marked as RADIO2
User manual
42
MARTECH RCD PRO
Below – indicated test points on front panel pcb. Signals U10 and U10 should be connected directly to
pins 10 and 11 of ic 4066 (look on picture above). Touch panel flex connect must be disconnected.
User manual
43
MARTECH RCD PRO
6.5.3 Algorithm for reading code from car / navi RNS315
Initial options : unit must have 3 code tries left
Functional diagram:
1. Remove the radio metal shields and CD drive
2. Desolder EEPROM 95256 from mainboard
3. With SPI_Tool Clip Portable Application version 1.2 make backup and set full memory protect –
function “Protect EEPROM Area”. Note, that SPI Tools work without Expander module!
4. Use “Read Status Register” for sure, that EEPROM has protected whole memory area.
5. Solder protected EEPROM on board with crossed WP signal (3pin of Eeprom) to GND (4pin of
EEPROM)
6. Connect the Expander signals from the radio plate according to the diagram to the radio /
navigation
7. Assemble the radio in a way that ensures the proper functioning of the device. Turn it on,
previously connect 12V power supply to the radio.
User manual
44
MARTECH RCD PRO
+12V GND
Run the application RCDPRO_RNS315
User manual
45
MARTECH RCD PRO
8. Perform Keyboard Test, additionally will be checked the keyboard connection
If the test is successful, the Clip will display a series of numbers, ie: 1,5,9,0, OK - DONE and
you should see these numbers being automatically selected and entered onto the radio display at the
same time. However, if the Clip displays the same numbers above, but nothing happens on the radio, or
you see the blank code entry square moving across the radio screen, then the test has been unsuccessful.
If all has failed, then you will need to recheck the solder connections that you have made between the
Expander and the radio.
9. Now you must disconnect radio power supply for 10 seconds, then connect it back but don’t turn
on. Radio must be turned off.
10. Choose function Find Code – Slow Mode
It is the function of retrieving the radio code according to the parameters by the user.
There we have the possibility of search settings in manual mode.
In manual mode you can set your code, from which the search will take place. For this purpose,
press Change and using CLIP keys: UP and DN, set the appropriate value of the initial code.
It should be noted that a single push of a code increment the value of the unit, and longer holding
the key UP or DN will increase in increments of code 10th.
Hit Start - search process starts.
User manual
46
MARTECH RCD PRO
Finding the code will be confirmed by an appropriate message.
11. Unplug the cables and desolder all crosses and wires.
Process completed.
User manual
47
MARTECH RCD PRO
6.6 RCDPRO_TechniSat
Module designed to work with Navi Dresden.
Required equipment:
- Martech CLIP with RCD PRO activation
- Martech CLIP Expander v1.1 with RCD210 module
- 12V/3A Power supply (for radio power supply)
Attention!
Navi Dresden requires EPMv1.0 Expander modification. Below you will find details.
6.6.1 Expander EPMv1.0 modifications for Navi Dresden
Perform selected connection between two signals on EPM module pcb (connect pin 8 of 4066 ic with
pin 6 of RJ45 socket).
High resolution photos are available under suport area.
User manual
48
MARTECH RCD PRO
6.6.2 Diagram connection scheme for Navi Dresden
You will need to connect signals to front panel pcb and to the radio pcb.
Below - indicated test points on the radio motherboard:
For example: R2.2, means pin second of RJ45 expander socket, marked as RADIO2.
User manual
49
MARTECH RCD PRO
Below – indicated test points on front panel pcb (connect signals from EPM to panel pcb):
For example Mx (where x is 1,2,3,4,5,6,7 or 8) means pins in RJ45 socket in EPMv1.0 expander.
Testpoint with arrow marked as M2&M1 means, you must connect both signals (M1, M2) from
EPMv1.0 to this signal on panel pcb.
High resolution photos are available under suport area.
Additionaly, connect signal R2.5 to system connector via 4k7 resistor:
User manual
50
MARTECH RCD PRO
Before starting the process, desolder 24c32 memory or lift up pin 7, then connect it to pin 8 of eeprom.
Example of properly assembled interface:
User manual
51
MARTECH RCD PRO
6.6.3 Algorithm for code reading from Navi Dresden
Functional diagram:
1. Remove the radio metal shields
2. Connect the Expander signals from the radio plate according to the diagram for the radio /
navigation. Run RCDPRO_TechniSat application.
3. Desolder 24c32 memory, located on radio PCB Or lift up pin 7, then connect it to pin 8 of
eeprom.
4. Perform Keyboard Test, additionally will be checked the keyboard connection
5. Program will ask for confirmation, choose „YES”
If the test is successful, the Clip will display a series of numbers, ie: 0,5,9,2, OK - DONE and
you should see these numbers being automatically selected and entered onto the radio display at
the same time. However, if the Clip displays the same numbers above, but nothing happens on
he radio, or you see the blank code entry square moving across the radio screen, then the test has
been unsuccessful.
If all has failed, then you will need to recheck the solder connections that you have made
between the Expander and the radio
6. Now you must disconnect radio power supply for 10 seconds, then connect it back but don’t turn
on. Radio must be turned off.
7. Choose function Find Code – Slow Mode
It is the function of retrieving the radio code according to the parameters by the user.
There we have the possibility of search settings in manual mode.
User manual
52
MARTECH RCD PRO
In manual mode you can set your code, from which the search will take place.
For this purpose, press Change and using CLIP keys: UP and DN, set the appropriate value of
the initial code. It should be noted that a single push of a code increment the value of the unit,
and longer holding the key UP or DN will increase in increments of code 10th.
8. Hit Start - search process starts.
9. Finding the code will be confirmed by an appropriate message.
12. Unplug the cables and desolder all wires.
Process completed
User manual
53
MARTECH RCD PRO
6.7 RCDPRO_GAMMA3
Module designed to work with Gamma 3 by Philips.
Required equipment:
• Martech CLIP with RCD PRO activation
• 12V/3A Power supply (for radio power supply)
Depending on the version we have:
• Radios based on 24c02 i 24c04 (Part number: 357 035 186G)
• Radios based on 24c04 i 24c04 (Part number: 357 035 186D)
Proper system identification is required to properly unlock the radio.
Attention!
GAMMA3 support requires connection to the radio directly from Clip (no Expander).
In addition, you need to build a small layout of the divider on the line with PORT2.4, and the layout of
the transistor and the resistor to the line PORT1.8.
User manual
54
MARTECH RCD PRO
6.7.1 Diagram connection scheme for GAMMA3
For the correct operation it requires only: the power connection and radio signals from PORT1 and
PORT2 of the CLIP by the following scheme:
•
•
•
•
•
from PORT1.4 to radio pcb
from PORT1.5 to radio pcb
from PORT1.8 through a simple arrangement of NPN transistor and a resistor to the radio pcb
from PORT2.4 through a resistor divider to the cassette mechanism PCB
from PORT2.7 to radio GND
User manual
55
MARTECH RCD PRO
Below – indicated test points on the radio motherboard:
It is to build a simple system based on an NPN transistor, and 470 Ohm resistor.
User manual
56
MARTECH RCD PRO
A simple modification should be performed on the cassette mechanism:
You will need two resistors: 2.7k and 5.1k - this is a simple resistor divider.
Radio power should be connected as follows:
User manual
57
MARTECH RCD PRO
Before starting the process, insert the cassette into the radio:
User manual
58
MARTECH RCD PRO
6.7.2 RCDPRO_GAMMA3 module functions
RCDPRO_GAMMA3 has following features:
•
•
•
•
•
Read Info – reads details about the connected radio.
Read EEPROM – reads the contents of the memory – thanks to this feature you can perform a
backup memory.
We recommend that you make a backup before starting the code searching.
Write EEPROM – writing the contents of the EEPROM
Power ON/OFF Test – testing the correctness of the on/off function
Find Code – Slow Mode – code serach function
User manual
59
MARTECH RCD PRO
6.7.3 Algorithm for reading code from GAMMA3
Functional diagram:
1. Remove the radio metal shields. Check on what kind of memories your radio is based and
choose proper one.
2. Connect signals from PORT1 i PORT2 to radio pcb, according to scheme from 6.7.1.
3. Connect 12V radio power supply, put cassette into radio. Be sure radio is turned off.
4. Perform Read Info function – thanks to this you will check system connection.
User manual
60
MARTECH RCD PRO
5. Use Read EEPROM to make security backup of radio memory.
6. Use Find Code – Slow Mode. Connect all signals, 12V power supply, put cassette inside, be sure
radio is turned off.
It is the function of retrieving the radio code according to the parameters by the user.
There we have the possibility of search settings in manual mode.
In manual mode you can set your code, from which the search will take place.
User manual
61
MARTECH RCD PRO
For this purpose, press Change and using CLIP keys: UP and DN, set the appropriate value of
the initial code. It should be noted that a single push of a code increment the value of the unit,
and longer holding the key UP or DN will increase in increments of code 10th.
Hit Start - search process starts.
Code will be read out whitin 56 minutes.
7. Finding the code will be confirmed by an appropriate message.
8. Unplug the cables and desolder all wires.
Process completed.
User manual
62