PACKAGE HEAT PUMP
INSTALLATION INSTRUCTIONS
Installer: Affix literature adjacent to the unit.
®
is a trademark of Maytag Corporation and is used under
license to Goodman Company, L.P. All rights reserved.
*NOTE: Please contact your distributor or our website
for the applicable product data book referred to in this
Part No. 10730420
Printed in USA
Goodman Company, L.P.
1810 Wilson Parkway • Fayetteville, Tennessee 37334
www.amana-hac.com
©2004 Goodman Company, L.P.
Effective: September 2004
SAFETY INSTRUCTIONS
RECOGNIZE SAFETY SYMBOLS, WORDS, AND LABELS
The following symbols and labels are used throughout this manual to indicate immediate or potential safety hazards. It is the owner’s and
installer’s responsibility to read and comply with all safety information and instructions accompanying these symbols. Failure to heed
safety information increases the risk of personal injury, property damage, and/or product damage.
WARNING
WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death.
CAUTION
CAUTION - Hazards or unsafe practices which COULD result in minor or moderate personal injury, product damage, property damage.
WARNING
TO AVOID PROPERTY DAMAGE, PERSONAL INJURY OR DEATH, DO NOT USE THIS UNIT IF ANY PART HAS BEEN UNDER WATER. IMMEDIATELY CALL A
QUALIFIED SERVICE TECHNICIAN TO INSPECT THE FURNACE AND TO REPLACE ANY PART OF THE CONTROL SYSTEM AND ANY GAS CONTROL HAVING BEEN
UNDER WATER.
WARNING
TO PREVENT PROPERTY DAMAGE, PERSONAL INJURY OR DEATH DUE TO IMPROPER INSTALLATION, ADJUSTMENTS, ALTERATIONS, SERVICE OR MAINTENANCE,
CONSULT THIS MANUAL, THE SERVICE MANUAL, A QUALIFIED INSTALLER OR A SERVICE AGENCY.
WARNING
THIS PRODUCT CONTAINS OR PRODUCES A CHEMICAL(S) WHICH MAY CAUSE DEATH OR SERIOUS ILLNESS AND WHICH ARE KNOWN BY THE STATE OF
CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.
ATTENTION INSTALLING PERSONNEL
As a professional installer you have an obligation to know the product better than the customer. This includes all
safety precautions and related items.
Prior to actual installation, thoroughly familiarize yourself with this Instruction Manual. Pay special attention to all safety
warnings. Often during installation or repair it is possible to place yourself in a position which is more hazardous than
when the unit is in operation.
Remember, it is your responsibility to install the product safely and to know it well enough to be able to instruct a
customer in its safe use.
Safety is a matter of common sense...a matter of thinking before acting. Most dealers have a list of specific good
safety practices...follow them.
The precautions listed in this Installation Manual are intended as supplemental to existing practices. However, if there
is a direct conflict between existing practices and the content of this manual, the precautions listed here take
precedence.
2
GENERAL INFORMATION
conditioned. The loads should be calculated by an approved method
or in accordance with A.S.H.R.A.E. Guide or Manual J - Load Calculations published by the Air Conditioning Contractors of America.
Obtain from:
TO THE INSTALLER
Before installing this unit please read this manual and the Product
Data Book applicable to your model* to familiarize yourself on the
specific items which must be adhered to such as maximum external
static pressure to unit, air temperature rise, minimum or maximum
CFM and motor speed connections.
American National Standards Institute
1430 Broadway
New York, NY 10018
TRANSPORTATION DAMAGE
TO THE OWNER
All units are securely packed in shipping containers tested according to International Safe Transit Association specifications. The carton should be checked upon arrival for external damage. If damage
is found, a request for inspection by carrier agent should be made in
writing immediately.
The unit should be carefully inspected upon arrival for damage and
bolts or screws which may have loosened in transit. In the event of
damage, the consignee should:
1. Make notation on delivery receipt of any visible damage to
shipment or container.
2. Notify carrier promptly and request an inspection.
3. In case of concealed damage, carrier should be notified as
soon as possible-preferably within 5 days.
4. File the claim with the following supporting documents within
the 9 month statute of limitations.
a. Original Bill of Lading, certified copy, or indemnity bond.
b. Original paid freight bill or indemnity in lieu thereof.
c. Original invoice or certified copy thereof, showing trade and
other discounts or reductions.
d. Copy of the inspection report issued by carrier
representative at the time damage is reported to the carrier.
The carrier is responsible for making prompt inspection of
damage and for a thorough investigation of each claim.
The distributor or manufacturer will not accept claims from
dealers for transportation damage.
NOTE: When inspecting the unit for transportation damage, remove
all packaging materials. Recycle or dispose of the packaging material according to local codes.
It is important to complete the owner registration card and mail it
immediately. This will assist us in contacting you if any service or
warranty information should change in the future. When completing
the registration card, be sure to include the Model, Manufacturing
and Serial Numbers, plus the installation date.
The warranty certificate is also supplied with the unit. Read the warranty carefully and note what is covered. Keep the warranty certificate in a safe place so you can find it if necessary.
If additional operating instructions are required, call the dealer where
the purchase was made. Keep this literature in a safe place for future reference.
UNIT PLACEMENT
WARNING
TO PREVENT POSSIBLE EQUIPMENT DAMAGE, PROPERTY DAMAGE, PERSONAL
INJURY OR DEATH, THE FOLLOWING BULLET POINTS MUST BE OBSERVED
WHEN INSTALLING THE UNIT.
ALL INSTALLATIONS:
Ground Level Installations Only:
•
•
When the unit is installed on the ground adjacent to the
building, a level concrete (or equal) base is recommended.
Prepare a base the same physical size as the unit or slightly
larger and 3 inches thick.
The base should also be located where no runoff of water
from higher ground can collect in the unit.
RIGGING AND HANDLING
Rooftop Installations Only:
•
To avoid possible personal injury or property damage, the
roof must have sufficient structural strength to carry the
weight of the unit(s) and snow or water loads as required by
local codes.
• If horizontal air delivery is used, the unit may be installed
directly on wood floors or on Class A, Class B, or Class C
roof covering material.
• To avoid possible personal injury, a safe, flat surface for
service personnel must be provided.
• If vertical air discharge is used and the unit is installed on
combustible flooring or class A, B, or C roofing material,
then the Amana® brand roof curb (PRC06A1 or PRC08A1)
is required.
This unit is approved only for an outdoor installation. To assure
that your unit operates safely and efficiently, it must be installed,
operated, and maintained in accordance with these installation and
operating instructions, all local building codes and ordinances.
The heating and cooling capacities of the unit should be greater than
or equal to the design heating and cooling loads of the area to be
WARNING
TO PREVENT PROPERTY DAMAGE, THE UNIT SHOULD REMAIN IN AN UPRIGHT
POSITION DURING ALL RIGGING AND MOVING OPERATIONS. TO FACILITATE
LIFTING AND MOVING WHEN A CRANE IS USED, PLACE THE UNIT IN AN
ADEQUATE CABLE SLING.
IMPORTANT: If using bottom discharge with roof curb, ductwork
should be attached to the curb prior to installing the unit. Ductwork
dimensions are shown in Amana® brand roof curb installation instructions.
Refer to the Roof Curb Installation Instructions for proper curb installation. Curbing must be installed in compliance with the National
Roofing Contractors Association Manual.
NOTE: Lower unit carefully onto roof mounting curb. While rigging
unit, center of gravity may cause condenser end to be lower than
supply air end.
*NOTE: Please contact your distributor or our website for the applicable product data book referred to in this manual.
3
THERMOSTAT WIRING
Fork Lift From
Back Of Unit
When an electric heater is installed, the thermostat wiring will be
made at the heater accessory box.
If a unit is installed without electric heaters, the low voltage wiring
to the blower section can be cut, either in the control box area or in
the blower section, to allow splicing-in of field-installed wiring, or
connect to terminal strip in unit control box.
See the unit wiring diagram for electrical connections.
ROOM THERMOSTAT
OUTDOOR UNIT
PH__C02E
C/X
G
Y
R
O
W1
W2
E
C/X
G
Y
R
O
W
W1
W2
Wiring shown is for D9945804 (THSMEC1H2BA) thermostat.
ROOM THERMOSTAT
C/X
G
Y
R
O
OUTDOOR UNIT
PH__C02E
C/X
G
Y
R
O
W2
E
W1
W2
Rigging
DUCT CONNECTIONS
W
Wiring shown is for 10636701(THSADC1H2BA) or
10636702 (THSMDC1H2BA) thermostat
HORIZONTAL AIRFLOW INSTALLATIONS
PHD60 TWO-STAGE
(24, 30, 36, 42 AND PHB48 MODELS)
Yellow No. 20 Wire in Blower Section
Two three-inch collar connections and two square flanges are shipped
with the unit. The collar connections are located in the return air
opening of the unit. The square flanges are inside the unit blower
compartment. The square flanges can be used for either connecting 16x16 ductwork to the unit or used with a Horizontal Duct Cover
kit (CHK001A).
To install the collar connections, remove the two collars, reverse and
snap them back into place in the outlet and inlet openings. Be sure
the flanges are to the outside of the unit. Secure with screws provided.
ROOM THERMOSTAT
C
G
Y2
OUTDOOR UNIT C/X
G
PHD60C02E
(HEATER KIT CONTROL BOX)
Y1
R
O
W1
W2
Y
R
O
W
W1
W3
W2
Wiring shown is for
1213412 (1F95-371) thermostat.
NOTE: If Electric Heater Kit is not installed or low voltage connection is made
in unit control box, connect as follows.
When using Amana® brand thermostat 1213412 on a two-stage cooling
unit, set the "select system type" on the thermostat programming to
Heat Pump 2 setting. This allows the "Y2" to energize. Any other
setting will cause the unit to be frozen on low stage cooling.
HORIZONTAL AIRFLOW INSTALLATIONS
(PHD48/60 and PHB60 models only)
These units are equipped with 14x14 square supply and return
air(PHD48/60 and PHB60 models only) openings for horizontal
air flow. The openings are flanged for ease of duct connection. A
16x16 Horizontal Duct Cover kit (CHK001A) can be used with the
clips provided with the unit.
THERMOSTAT PLACEMENT
Thermostat should be mounted 5 feet above the floor, on a vibration free inside wall in a room or a hallway that has good air circulation.
Movement of air should not be obstructed by furniture, door, draperies, etc. The thermostat should not be mounted where it will be affected by drafts, hot or cold water pipes or air ducts in walls, radiant
heat from fireplace, lamps, the sun, television, etc. Consult the Instruction Sheet packaged with thermostat for mounting instructions.
ROOM THERMOSTAT
C
G
Y2
Y1
R
O
W1
OUTDOOR UNIT
PHD60C02E
(CONTROL BOX)
C
G
Y
Y1
R
O
W
W2
W3
Wiring shown is for 1213412 (1F95-371) thermostat.
Typical Thermostat and Unit 24 Volt Wiring Hookup
ELECTRICAL CONNECTIONS
NOTE: The units are designed for operation on 60 Hz current and
at the voltages shown on the rating plate. All internal wiring in the
unit is complete. For the PHB**CC and PHD**CC units, the power
supply connection for the heater and unit will be at the circuit breaker
in the heater control box. For all others, the power supply may be
brought into the contactor (refer to unit wiring diagram supplied
with unit). Ensure 24 volt wiring is connected between the unit
control panel and the room thermostat. See the following figures
for low voltage field connection.
WARNING
SHOCK HAZARD!
DISCONNECT ALL ELECTRICAL POWER BEFORE ELECTRICALLY CONNECTING
OR SERVICING THIS UNIT. FAILURE TO DISCONNECT THE ELECTRICAL POWER
BEFORE WORKING ON THIS PRODUCT CAN CREATE A HAZARD LEADING TO
PERSONAL INJURY OR DEATH.
4
Low Voltage
Terminal Strip
CAUTION
TO AVOID PROPERTY DAMAGE OR PERSONAL INJURY DUE TO FIRE, USE
ONLY COPPER CONDUCTORS.
C
G
Y
R
W
CAUTION
ON
W1
ON
W2 O
TO PREVENT IMPROPER AND DANGEROUS OPERATION DUE TO WIRING
ERRORS, LABEL ALL WIRES PRIOR TO DISCONNECTION WHEN SERVICING
CONTROLS.
VERIFY PROPER OPERATION AFTER SERVICING.
The best protection for the wiring is the lowest rated fuse or circuit
breaker which will supply power to the unit during normal operation
without nuisance trips. Such a device will provide maximum circuit
protection. DO NOT EXCEED THE MAXIMUM OVERCURRENT
DEVICE SIZE SHOWN ON UNIT DATA PLATE.
All line voltage connections must be made through weatherproof
fittings. All exterior power supply and ground wiring must be in
approved weatherproof conduit. Low voltage wiring from the unit
control panel to the thermostat requires coded cable.
Low Voltage Connection
Heater Kit Control Box
Low Voltage
Terminal Strip
FLEXIBLE WIRING SETUP
Line and low voltage wiring must enter the unit as shown.
REAR VIEW
ELECTRICAL
Low Voltage Connection
Unit Control Box
T2
RETURN
AIR
SUPPLY
AIR
T1
SIDE VIEW
SIDE VIEW
HEATER
KIT
BLOWER
TO CONTACTOR
GN
BK
ELECTRICAL
LOW
VOLTAGE
THERMOSTAT
BU
G
GY
Y
YL
R
RD
W
BR
W1
BR
RD
5
1
VT
RD
RD
BK
BK
BR
BU
O
0R
For knockout locations, see dimension drawing in the Product Data
Book applicable to your model* . Use the Single Point wiring kit to
add further flexibility to the installation wiring.
BU
RD
BR
YL
1
2
3
4
5
6
7
8
9
L2
USE COPPER
CONDUCTORS
ONLY-75°C MIN
CB1
L1
SEQUENCER #1
BK
FIELD
CONNECTION
208/240 VAC
1ø
L1
4
BK
3
BK
W2
GY
L2
CB2
BK
BK
COMPRESSOR
EVAP
COIL
GND-75
C
ELECT.
CONTROL
BOX
UNIT VOLTAGE
208/230 VAC 1ø
The unit transformer is factory connected for 230V operation. If the
unit is to operate on 208V, reconnect the transformer primary lead
as shown on the unit wiring diagram.
RD
RD
VT
OL
BK
BK
OL
10KW
AIR CIRCULATION AND FILTERS
Field Connection
DOWNSHOT AIRFLOW CONVERSION
Refer to the unit wiring diagram (see back of manual) for electrical
connections. When installed, the unit must be electrically grounded
in accordance with local codes or in the absence of local codes,
with the National Electrical Code, ANSI/NFPA No. 70, and/or the
CSA C22.1 Electrical Code, if an external source is utilized.
Units are shipped from the factory ready for horizontal airflow. These
units can be easily converted from horizontal to downshot airflow
delivery. If conversion to vertical airflow is necessary, proceed as
follows:
Blower Rotation
WARNING
1. Cut insulation around bottom openings and remove panels
from the bottom of the unit, saving the screws holding the
panels in place.
2. From the rear of the unit, remove the four (4) screws
securing the blower assembly in place and loosen the two
(2) screws directly below the duct opening.
TO AVOID THE RISK OF PERSONAL INJURY OR DEATH DUE TO ELECTRICAL
SHOCK, WIRING TO THE UNIT MUST BE POLARIZED AND GROUNDED.
*NOTE: Please contact your distributor or our website for the applicable product data book referred to in this manual.
5
require that cover clips (included with the unit) be installed to ensure a secure fit of the Horizontal Duct Covers.
24, 30, 36, 42 AND PHB48 Models:
Remove
1. Remove and set aside the four (4) supply air side screws.
2. Remove and set aside the two (2) return air side screws.
REMOVE
SCREWS
REMOVE
SCREWS
Loosen
Duct Removal
3. Remove the clamp securing the blower assembly to the
bottom of the unit. Discard clamp and screws.
SUPPLY AIR
{}
Supply Air Side Screws Removal
3. Center flange bracket and unit openings. Attach flange
brackets to the unit using the removed screws in Step 1.
Retighten screws.
4. Drill two 1/8” diameter holes on the return air side as
indicated in the figure below.
5. Secure the return air side flange bracket with the two (2)
self-tapping screws included with the unit.
Airflow
Remove
Clamp Removal
5. Rotate the blower assembly 90° clockwise, setting the
blower assembly outlet on the panel removed from bottom
of the unit.
Ensure the blower motor is oriented with the motor wires
at the bottom. This keeps condensate from puddling
inside the blower motor and causing motor failure. If
the motor is not oriented correctly, loosen the motor belly
band and rotate the motor to the correct position, then
retighten the motor belly band.
Install Screws
Removed From
Back Panel
A
lo
ir f
RETURN AIR
FLANGE BRACKETS
SUPPLY AIR
Drill 2-1/8"
Dia. holes
RETURN AIR
Flange Bracket Installation
6. Align the horizontal duct covers over the flange brackets
just installed and secure with screws included in the
Horizontal Duct Cover kit.
w
Motor Leads MUST
exit at bottom
Vertical Blower Assembly
6. Secure the blower assemblyy with screws removed in step
1.
HORIZONTAL DUCT COVER INSTALLATION
The second step in the downshot airflow conversion is to install Horizontal Duct Covers. Horizontal Duct Covers are an accessory, and
Horizontal Duct Cover Alignment
can be purchased from your authorized dealer. The kit number is
CHK001A.
PHD48/60 and PHB60 Models:
PHB/PHD Models 24, 30, 36, 42, and PHB48 require that the sup1. Install cover clips (included with unit) on the inner flange
ply and return air openings be converted to square. Flanges are
sides using existing flange hole.
shipped with these units to complete this conversion.
2. With self-drilling screws provided, attach clips to the unit.
Models PHD48/60 and PHB60 supply and return air openings are
square and do not require a flange conversion. They do, however,
6
Even though a return air filter is not supplied with this unit, there
must be a means of filtering all return air.
Refer to the following table or the Product Data Book applicable to
your model* for filter size information.
CLIPS
MODEL
PHB24C02*
PHB30C02*
PHB36C02*
PHB42C02*
PHB48C02*
PHB60C02*
SELF-DRILLING
SCREWS
Cover Clip Installation
3. Attach 16x16 horizontal covers using screws provided with
kit to the outer duct opening flange and cover clip holes.
4. Secure the center of the top flat cover flange to the unit
using a self-drilling screw included with the unit.
Horizontal Duct Cover Installation
DUCTWORK
Duct systems and register sizes must be properly designed for the
C.F.M. and external static pressure rating of the unit. Ductwork should
be designed in accordance with the recommended methods of Air
Conditioning Contractors of America Manual D (Residential) or
Manual Q (Commercial). All ductwork exposed to the outdoors must
include a weatherproof barrier and adequate insulation.
A duct system should be installed in accordance with Standards of
the National Board of Fire Underwriters for the Installation of Air Conditioning, Warm Air Heating and Ventilating Systems. Pamphlets No.
90A and 90B.
The warm air supply duct from the unit through a wall fabricated of
combustible material may be installed without clearance. However,
minimum clearances for the unit must be observed (see appendix in
back of manual).
The outlet duct should be provided with an access panel.
For vertical airflow, the ductwork should be attached to the roof curb
prior to installing the unit. Ductwork dimensions are shown in the
Amana ® PRC roof curb installation manual.
If desired, supply and return duct connections to the unit may be
made with flexible connections to reduce possible unit operating
sound transmission.
RATED
DISPOSABLE PERMANENT COOLING
FILTER (ft 2 )2 AIRFLOW
FILTER (ft 2 )1
(CFM)
3.0
1.5
850
3.4
1.7
960
4.0
2
1170
4.5
2.3
1350
5.5
2.8
1550
6.5
3.3
1750
PHB24CC2*
PHB30CC2*
PHB36CC2*
3.0
3.4
4.0
1.5
1.7
2
850
960
1170
PHD24C02*
PHD30C02*
PHD36C02*
PHD42C02*
PHD48C02*
PHD60C02*
3.0
3.4
3.0
3.4
5.5
6.5
1.5
1.7
1.5
1.7
2.8
3.3
810
1020
1100
1200
1550
1750
PHD24CC2*
PHD30CC2*
PHD36CC2*
3.0
3.4
4.0
1.5
1.7
2
810
1020
1100
1
Bas ed on a f ace v elocity of 300 f t./min.
2
Bas ed on a f ace v elocity of 600 f t./min.
If using the Over/Under Transition Kit, the filter(s) may be located in
the return air duct(s) or return air filter grille(s). Filters installed external to the unit should be sized in accordance with their manufacturer
recommendations. A throwaway filter must be sized for a maximum
face velocity of 300 feet per minute.
FILTER INSTALLATION
Important: When installing a filter, the air flow arrows on the filter
must point toward the circulating air blower.
CONDENSATE DRAIN
CONDENSATE DRAIN CONNECTION
An external condensate drain trap is required with this unit. See
your distributor for details. For proper unit operation, the trap must
be filled either before a cooling startup or during a unit “cycle-off”
after 20 minutes of running on first cycle. This drain can be extended using 3/4” PVC piping.
FILTERS
WARNING
TO AVOID PROPERTY DAMAGE, PERSONAL INJURY OR DEATH, DISCONNECT
NEVER OPERATE FURNACE
ELECTRICAL POWER BEFORE REMOVING FILTERS.
WITHOUT A FILTER INSTALLED BECAUSE DUST AND LINT WILL BUILD UP ON
INTERNAL PARTS RESULTING IN LOSS OF EFFICIENCY, EQUIPMENT DAMAGE
AND POSSIBLE FIRE.
*NOTE: Please contact your distributor or our website for the applicable product data book referred to in this manual.
7
OPERATING INSTRUCTIONS
1. Turn ON the electrical power supply to the unit.
2. Place the room thermostat selector switch in the COOL or
HEAT position (or AUTO if available, and if automatic
changeover from cooling to heating is desired).
3. Set the room thermostat to the desired temperature.
1-1/2" Minimum
drop at outlet
MAINTENANCE
90° ELL
WARNING
Condensate
Drain Trap 2-1/2" of
3/4" PVC
TO AVOID PERSONAL INJURY OR DEATH DUE TO ELECTRICAL SHOCK,
Figure 13 - Condensate Drain Connection
DISCONNECT ELECTRICAL POWER BEFORE PERFORMAING ANY
NORMAL SEQUENCE OF OPERATION
MAINTENANCE.
REPLACING OR CLEANING FILTER
NOTE: There is a fan delay on initial power to unit before the low
voltage board resets and is operational.
A return air filter is not supplied with this unit; however, there must be
a means of filtering all of the return air. The filter(s) may be located in
the return air duct(s), or return air filter grille(s). Consult with your
installing dealer for the actual location of the return air filter(s) for
your unit.
Dirty filters are the most common cause of inadequate heating or
cooling performance. Filter inspection should be made at least every two months; more often if necessary because of local conditions
and usage.
Dirty throwaway filters should be discarded and replaced with a new,
clean filter. Dirty permanent filters should be washed with water, thoroughly dried and sprayed with a filter adhesive before being reinstalled. (Filter adhesives may be found at many hardware stores.)
Permanent filters should last several years; however, should one
become torn or uncleanable, it should be replaced.
1. Thermostat calls for heating or cooling. The compressor and
outdoor fan are energized.
2. Approximately 10 seconds later, the indoor fan starts.
3. The unit will deliver heating or cooling to the conditioned
space until the thermostat is satisfied.
NOTE: PHD60 TWO-STAGE COOLING
If the room temperature is 4°F higher than thermostat
setpoint, the indoor fan will run at high speed, and the
compressor at full load. If the room temperature is within
2°F of thermostat setpoint; the indoor fan will shift to low
speed and the compressor will unload to a lower capacity.
4. The compressor and outdoor fan will be de-energized when
the thermostat opens.
5. The indoor fan continues to run for approximately 60 seconds
after the thermostat is satisfied. This allows additional cooling
from the indoor coil to be transferred to the conditioned
space. Then, the indoor fan stops.
MAINTAINING CABINET FINISH
Use a fine grade automotive wax on the cabinet finish to maintain
the finish’s original high luster. This is especially important in areas
with high ultraviolet radiation.
CLEAN OUTSIDE COIL (QUALIFIED SERVICER ONLY)
STARTUP AND ADJUSTMENT
The coil with the outside air flowing over it should be inspected annually and cleaned as frequently as necessary to keep the finned
areas free of lint, hair and debris.
WARNING
CONDENSER AND EVAPORATOR MOTORS
TO PREVENT PERSONAL INJURY OR DEATH, ALWAYS DISCONNECT THE
ELECTRICAL POWER BEFORE INSPECTING OR SERVICING THE UNIT. SINCE ALL
Bearings on the evaporator motor and the condenser motor are permanently lubricated. No additional oiling is required.
OF THE COMPRESSOR PROTECTION DEVICES RESET AUTOMATICALLY,
THE CONTACTOR AND OUTDOOR FAN MAY BE ENERGIZED WHEN RESET.
WARNING
WARNING
TO AVOID PERSONAL INJURY OR DEATH DUE TO ELECTRIC SHOCK, DO NOT
REMOVE ANY INTERNAL COMPARTMENT COVERS OR ATTEMPT ANY
THIS UNIT MUST NOT BE USED AS A "CONSTRUCTION HEATER" DURING THE
FINISHING PHASES OF CONSTRUCTION ON A NEW STRUCTURE. THIS TYPE OF
ADJUSTMENT.
USE MAY RESULT IN PREMATURE FAILURE OF THE UNIT DUE TO EXTREMELY
LOW RETURN AIR TERMPERATURES AND EXPOSURE TO CORROSIVE OR VERY
CAUTION
DIRTY ATMOSPHERES.
COMPRESSOR PROTECTION DEVICES
ALWAYS VERIFY PROPER OPERATION AFTER SERVICING.
This package heat pump unit compressor includes components which
are designed to protect the compressor against abnormal operating
conditions.
8
ACCESSORIES
Horizontal Duct Covers (CHK001A)
Single Point Power Connections (SPK**A)
Roof Curb - Heat Pump (PRC06A1)
Roof Curb - Universal (PRC08A1)
Over-Under to Side by Side (PDTROU4A)
Over-Under to Side by Side (PDTROU6A)
Additional accessories, as described above, can be purchased to
fit specific application needs. Accessories can be ordered by the
part numbers in the table and each accessory includes its own
separate instructions.
REPLACEMENT PARTS
Refer to the description in the Parts Catalog when ordering any
part. Be sure to provide the unit model, manufacturing, and serial
numbers with the order.
NOTE: Details for installing and wiring electric heater kits and single
point wiring kits are contained in the installation instructions for these
accessories.
9
WARNING
DISCONNECT ELECTRICAL POWER TO THIS UNIT BEFORE SERVICING OR PERFORMING MAINTENANCE. FAILURE TO DISCONNECT
THE ELECTRICAL POWER BEFORE WORKING ON THIS PRODUCT CAN CREATE A HAZARD LEADING TO PROPERTY DAMAGE,
PERSONAL INJURY OR DEATH.
208 VOLT INSTALLATION
ELECTRIC
HEAT
RELAY
W2 W1 G
E
C
R
W O
Y
ELECTRIC
HEATER
SEQ
NO#1
CAPACITOR
(CAP)
AIR
CIRCULATION
BLOWER
(ACB)
BR
SEQ
NO#1
BR
6
ELECTRIC
HEAT RELAY
230
DFT
COMMON
1
2
HI
3
MED HI
4
5
MED LOW
BU-23
RD-33
WH-7
R
W2
4
9
8
7
START
RELAY
COOLING
BLOWER
SPEED TAP
CAP
CC
L1
PHCB05C1
DOWN
PHB24C02**
L2
208/230 VAC 1Ø
WARNING:DISCONNECT POWER BEFORE SERVICING.
USE COPPER CONDUCTORS ONLY
LOW
PHB30C02**
MED-LOW
PHB36C02**
MED-HIGH
MED
LOW
MED
LOW
MED
LOW
HORIZ
LOW
LOW
LOW
PHCB10C1
DOWN
MED
LOW
MED
LOW
MED
LOW
HORIZ
LOW
LOW
LOW
GY-55
TEST
90
60
30
PHCB15C1
DOWN
HORIZ
MED
HIGH
MED
HIGH
MED
HIGH
MED
HIGH
MED
HIGH
MED
HIGH
PHCB20C1
DOWN
HIGH
HORIZ
TEST
5
90
90
60
30
2
MODEL
NUMBER
HERM
CAPACITOR
22303301 REV. 1
ELECTRIC HEAT BLOWER TAP
T2
FAN
BU-34
C
1
O.D.
FAN
MOTOR
ALTERNATE UNIT POWER REFRIGERANT
LEADS MAY BE USED WITH ELECTRIC
HEATER ACCESSORIES. SEE HEATER
ACCESSORY INSTALLATION INSTRUCTIONS.
COMP
S
COM
RD-27
RD
BK
GN
R
START
DFT
5
COM
T1
R
6
VIEW A-A
OD
CAP
VT
16
DEFROST
BOARD
FAN
HERM
R
COOLING
TAP
1
CAP
FAN
W2
NO
DF2
COM
2
YL
12
BR-11
CAP
3
C
BK-27
1
HI
MD HI
MD LO
LO
NC
A
S
ELECTRIC
HEAT
RELAY
RD-31
DF1
COOLING
SWITCH
RELAY
W
TO
HEATER
KIT
2
G
PIN 1
Y
PIN 3
C
PIN 4
O
PIN 5
R
PIN 6
R
RD
31
1
5
4
O
R
XFMR R
G
XFMR C
C
PIN 7
RD-22
BR-21
RD-13
OR-49
BK-26
VT-18
YL-27
OR-49
BR-21
RD-13
BU-34
GY-70
PIN 8
3
YL-27
O
TEST
A
Y
C
Y
O
SWITCH
RELAY
COMPRESSOR
1 Ø WIRING
RD
10
BK-20
PIN 2
HEAT
TAP
VT
20
BU
23
VT-18
C
O
BK-26
BU-1
PIN 9
COOLING
2
VT-62
BK-19
CC
5
RD-10
COOLING
SWITCH
RELAY
OR-28
W
ACB
RD-27
NO NC
G
C
REVERSING
SOLENOID
(RS)
RD
31
BU-1
VT-20
R
BK-24
RS
4
VT
62
COM
XFMR-R
BK-13
O
USE COPPER
CONDUCTORS
ONLY75 °C MIN
GY-9
LOW
Y
230/208
L2
VT-14
XFMR-C
24V
L1
GY-8
R
COMMON
L1
HIGH
HIGH
HIGH
BR BROWN
60
OR ORANGE
WH WHITE
30
VT VIOLET
BU BLUE
GN GREEN
GY GRAY
TEST
BK BLACK
RD RED
TEST
HIGH
HIGH
COLOR CODE
YL YELLOW
LOW VOLTAGE
LOW VOLTAGE FIELD
ALTERNATE
CONFIGURATION
DETAIL 1
HI VOLTAGE
HI VOLTAGE FIELD
PHB[24-36]C02*
C
G
ELECTRIC
HEAT
RELAY
T1
CONTACTOR(CC)
L2
T2
VT-14(COMMON)
RD-24(COOL)
RD-11
BU-23(HEAT)
DEFROST
THERMOSTAT
(DT)
DT
R
10
90
60
30
GND
RD-6
208
RD-24
TERMINAL BOARD
DEFROST
BOARD
VT-7
LINE
LOAD
FIELDCONNECTION
208/230VAC1Ø
GY-9
TO HEATER KIT
DF1
COM
230/208
HEATER
KIT
DF2
GND
TRANSFORMER
FOR PROPER OPERATION ON 208 VOLT THE
FOLLOWING CHANGE MUST BE MADE:
MOVE RD6 WIRE FROM TRANSFORMER
230 TERMINAL TO 208 TERMINAL.
WARNING
DISCONNECT ELECTRICAL POWER TO THIS UNIT BEFORE SERVICING OR PERFORMING MAINTENANCE. FAILURE TO DISCONNECT
THE ELECTRICAL POWER BEFORE WORKING ON THIS PRODUCT CAN CREATE A HAZARD LEADING TO PROPERTY DAMAGE,
PERSONAL INJURY OR DEATH.
208 VOLT INSTALLATION
ELECTRIC
HEAT
RELAY
W2 W1 G
E
C
R
W O
Y
ELECTRIC
HEATER
SEQ
NO#1
CAPACITOR
(CAP)
AIR
CIRCULATION
BLOWER
(ACB)
BR
SEQ
NO#1
BR
6
ELECTRIC
HEAT RELAY
230
DFT
C
2
3
4
HI
MED
LOW
BU-23
RD-33
WH-7
YL\BK
W2
A
4
9
8
7
START
RELAY
COOLING
BLOWER
SPEED TAP
PHCB07C1
DOWN
HORIZ
PHCB10C1
DOWN
HORIZ
GY-55
HORIZ
PHCB20C1
DOWN
HORIZ
CAP
CC
L1
PHB42C02**
208/230 VAC 1Ø
TEST
90
60
30
PHCB15C1
DOWN
L2
WARNING:DISCONNECT POWER BEFORE SERVICING.
USE COPPER CONDUCTORS ONLY
PHB48C02**
LOW
MED
LOW
MED
LOW
MED
LOW
MED
LOW
MED
LOW
MED
LOW
MED
MED
HIGH
TEST
5
90
90
60
30
2
MODEL
NUMBER
HERM
CAPACITOR
22303901 REV. 1
ELECTRIC HEAT BLOWER TAP
T2
FAN
BU-34
C
1
O.D.
FAN
MOTOR
ALTERNATE UNIT POWER REFRIGERANT
LEADS MAY BE USED WITH ELECTRIC
HEATER ACCESSORIES. SEE HEATER
ACCESSORY INSTALLATION INSTRUCTIONS.
COMP
S
COM
RD-27
RD
BK
GN
R
START
DFT
5
COM
T1
R
6
VIEW A-A
OD
HERM
VT
16
DEFROST
BOARD
FAN
CAP
R
COOLING
TAP
1
CAP
FAN
W2
COM
2
YL
12
BR-11
CAP
3
C
BK-27
1
HI
MED
LO
NC
NO
O
COOLING
SWITCH
RELAY
DF2
HEAT
TAP
2
A
S
ELECTRIC
HEAT
RELAY
RD-31
DF1
5
W
ACB
2
G
TO
HEATER
KIT
4
Y
PIN 1
C
PIN 2
O
PIN 5
R
PIN 6
R
RD
31
1
5
4
O
R
XFMR R
G
XFMR C
C
PIN 7
RD-22
BR-21
RD-13
OR-49
BK-26
VT-18
YL-27
OR-49
BR-21
RD-13
BU-34
GY-70
PIN 8
3
YL-27
Y
C
Y
O
SWITCH
RELAY
COMPRESSOR
1Ø WIRING
RD
10
BK-19
PIN 3
230/208
VT
20
BU
23
VT-18
BK-20
PIN 4
24V
VT-62
BK-26
PIN 9
COMMON
RD-10
COOLING
SWITCH
RELAY
OR-28
RS
LPS
RD-27
NO NC
G
C
C
O
TEST
VT-20
R
REVERSING
SOLENOID
(RS)
RD
31
YL\BK
COM
XFMR-R
BK-24
W
USE COPPER
CONDUCTORS
ONLY75°C MIN
VT
62
GY-8
BK-13
COOLING
L2
RD-24
Y
CC
L1
GY-9
5
XFMR-C
O
L1
VT-14
LOW
PRESSURE
SWITCH
R
G
ELECTRIC
HEAT
RELAY
T1
CONTACTOR(CC)
L2
T2
VT-14(COMMON)
RD-24(COOL)
RD-11
BU-23(HEAT)
R
11
90
60
30
GND
RD-6
208
COLOR CODE
YL YELLOW
BR BROWN
60
OR ORANGE
WH WHITE
30
VT VIOLET
BU BLUE
GN GREEN
GY GRAY
TEST
BK BLACK
RD RED
TEST
MED
LOW VOLTAGE
LOW VOLTAGE FIELD
ALTERNATE
CONFIGURATION
HIGH
DETAIL 1
HI VOLTAGE
HI VOLTAGE FIELD
PHB[42-48]C02**
R
DT
COMMON
1
DEFROST
THERMOSTAT
(DT)
TERMINAL BOARD
DEFROST
BOARD
VT-7
LINE
LOAD
FIELDCONNECTION
208/230VAC1Ø
GY-9
TO HEATER KIT
DF1
COM
230/208
HEATER
KIT
DF2
GND
TRANSFORMER
FOR PROPER OPERATION ON 208 VOLT THE
FOLLOWING CHANGE MUST BE MADE:
MOVE RD6 WIRE FROM TRANSFORMER
230 TERMINAL TO 208 TERMINAL.
WARNING
DISCONNECT ELECTRICAL POWER TO THIS UNIT BEFORE SERVICING OR PERFORMING MAINTENANCE. FAILURE TO DISCONNECT
THE ELECTRICAL POWER BEFORE WORKING ON THIS PRODUCT CAN CREATE A HAZARD LEADING TO PROPERTY DAMAGE,
PERSONAL INJURY OR DEATH.
208 VOLT INSTALLATION
Y
BLOWER
INTERFACE
HE AT
A
B
C
D
A
B
C
D
COOL
W
NORM
( )+
(-)
T EST
W2
PIN 1
R
O
A
BK
19
VT
20
YL/BK
LOWPRESSURE
SWITCH(LPS)
8
7
DFT
9
BR-11
DF1
VT
16
90
60
30
DF2
O.D.
FAN
MOTOR
1
RD
BK
GN
ALTERNATE UNIT POWER REFRIGERANT
LEADS MAY BE USED WITH ELECTRIC
HEATER ACCESSORIES. SEE HEATER
ACCESSORY INSTALLATION INSTRUCTIONS.
20424101 REV. 3
BU-34
DETAIL 2
R
HERM
COMP
ADJUST
CFM
90
CFM (HEAT)
(COOL)
T2
T1
2
5
START
RELAY
CAP
NORM
A
1350
A
1450
(+)
B
1550
B
1650
B
(-)
C
1750
C
1850
C
TEST
D
1950
D
2000
D
A
TEST
S
1
90
60
30
C
START
208/230 VAC 1 Ø
WARNING:DISCONNECT POWER BEFORE SERVICING.
USE COPPER CONDUCTORS ONLY
COLOR CODE
YL YELLOW
BR BROWN
60
OR ORANGE
WH WHITE
30
VT VIOLET
BU BLUE
GN GREEN
GY GRAY
TEST
BK BLACK
RD RED
TEST
LOW VOLTAGE
LOW VOLTAGE FIELD
ALTERNATE
CONFIGURATION
L2
L1
HERM
RD-27
FAN
COM
FAN
CAPACITOR
DEFROST
BOARD
230/208
CC
BK-27
COM
COMMON
24V
CAP
C
YL
12
W
4
G
5
Y
6
O
1
C
2
R
C
3
VIEW A-A
OD
S
BR-21
CC
CAP
R
VT
62
OR-49
G
LPS
COMPRESSOR
1Ø WIRING
RD
10
RD-13
W
RS
RD
31
RD-10
YL-27
O
Y
O
Y
TO
HEATER
KIT
VT-20
TEST
C2
G
C1
O
R3
R
PIN 2
BK
20
W1
EM/W2
O
R2
R3
C1
C2
G
Y/Y2
R
12
PIN 4
C
REVERSING
SOLENOID
(RS)
BK
24
R
R2
DFT
PIN 5
VT
62
RD-27
BK
13
A
B
C
D
A
B
C
D
YL-27
OR-49
BR-21
RD-13
BU-34
GY-70
PIN 6
FAN
USE COPPER
CONDUCTORS
ONLY75 °C MIN
YL/BK
DEFROST
THERMOSTAT
(DT)
CU T TO
EN ABLE
DE HUM ID IFY
HEAT
COOL
GY
8
R
W1
Y/Y2
ADJUST
A
PIN 3
TEST
BLOWER
INTERFACE
PIN 7
DT
RD
33
W2
EM/W2
SEE DETAIL 2
TERMINAL BOARD
90
60
30
L2
VT-14
GY-8
PIN 8
DEFROST
BOARD
L1
GY-9
PIN 9
DF1
L1
CONTACTOR(CC)
L2
T2
INDUCTOR (OPTIONAL)
HEATER
KIT
DF2
GY-9
RD-31
O
W2
T1
O
W1
GND
RD-6
208
Y
G
230
C
E
VT-7
LINE
LOAD
FIELDCONNECTION
208/230VAC1Ø
DETAIL 1
HI VOLTAGE
HI VOLTAGE FIELD
PHB60 / PHD48C02**
TO HEATER KIT
R
C
AD JUST
NOR M
( )+
(-)
TEST
O
COM
CU T TO
EN ABLE
INDUCTOR (OPTIONAL)
AIR
CIRCULATION
BLOWER
RD-31
(ACB)
DE HUM ID IFY
AIR
CIRCULATION
BLOWER
(ACB)
GND
TRANSFORMER
FOR PROPER OPERATION ON 208 VOLT THE
FOLLOWING CHANGE MUST BE MADE:
MOVE RD6 WIRE FROM TRANSFORMER
230 TERMINAL TO 208 TERMINAL.
VT-14
WARNING
DISCONNECT ELECTRICAL POWER TO THIS UNIT BEFORE SERVICING OR PERFORMING MAINTENANCE. FAILURE TO DISCONNECT
THE ELECTRICAL POWER BEFORE WORKING ON THIS PRODUCT CAN CREATE A HAZARD LEADING TO PROPERTY DAMAGE,
PERSONAL INJURY OR DEATH.
208 VOLT INSTALLATION
ELECTRIC
HEAT
RELAY
W2 W1 G
E
C
R
W O
Y
ELECTRIC
HEATER
SEQ
NO#1
AIR
CIRCULATION
BLOWER
(ACB)
BR
SEQ
NO#1
BR
TO HEATER KIT
ELECTRIC
HEAT RELAY
6
230
DFT
C
4
5
2
HI
3
MED HI
MED LOW
BU-23
RD-33
WH-7
YL\BK
W2
2
1
6
5
4
9
8
7
COMP
C
1
2
5
MODEL
NUMBER
START
RELAY
COOLING
BLOWER
SPEED TAP
PHCB05C1
DOWN
CAP
CC
PHD24C02**
208/230 VAC 1 Ø
GY-55
TEST
90
L2
WARNING:DISCONNECT POWER BEFORE SERVICING.
USE COPPER CONDUCTORS ONLY
LOW
PHD30C02**
MED-LOW
PHD36C02**
MED-HIGH
MED
LOW
MED
LOW
MED
LOW
HORIZ
LOW
MED
MED
PHCB10C1
DOWN
MED
LOW
MED
LOW
MED
LOW
HORIZ
LOW
MED
MED
PHCB15C1
DOWN
HORIZ
MED
HIGH
MED
HIGH
MED
HIGH
MED
HIGH
MED
HIGH
MED
HIGH
PHCB20C1
DOWN
HIGH
HORIZ
TEST
START
T2
HERM
CAPACITOR
22304001 REV. 1
ELECTRIC HEAT BLOWER TAP
S
FAN
BU-34
90
60
30
R
O.D.
FAN
MOTOR
ALTERNATE UNIT POWER REFRIGERANT
LEADS MAY BE USED WITH ELECTRIC
HEATER ACCESSORIES. SEE HEATER
ACCESSORY INSTALLATION INSTRUCTIONS.
RD
BK
GN
COM
T1
90
60
30
VIEW A-A
OD
COM
RD-27
FAN
HERM
VT
16
DEFROST
BOARD
CAP
CAP
DFT
COOLING
TAP
3
YL
12
BR-11
CAP
COM
FAN
R
MD HI
MD LO
LO
C
BK-27
1
HI
NC
NO
R
COOLING
SWITCH
RELAY
DF2
HEAT
TAP
2
A
S
ELECTRIC
HEAT
RELAY
RD-31
DF1
5
W
ACB
2
G
TO
HEATER
KIT
4
Y
PIN 1
C
PIN 2
O
PIN 5
R
PIN 6
R
RD
31
1
5
4
W2
PIN 7
RD-22
BR-21
RD-13
OR-49
BK-26
VT-18
YL-27
OR-49
BR-21
RD-13
BU-34
GY-70
PIN 8
3
YL-27
O
TEST
A
O
R
XFMR R
G
XFMR C
C
SWITCH
RELAY
COMPRESSOR
1Ø WIRING
RD
10
BK-19
PIN 3
230/208
VT
20
BU
23
VT-18
Y
C
Y
O
BK-26
BK-20
PIN 4
24V
VT-62
C
O
COMMON
RD-10
COOLING
SWITCH
RELAY
OR-28
RS
LPS
RD-27
NO NC
G
C
PIN 9
L1
VT-20
R
REVERSING
SOLENOID
(RS)
RD
31
YL\BK
COM
XFMR-R
BK-24
W
USE COPPER
CONDUCTORS
ONLY75°C MIN
VT
62
GY-8
BK-13
COOLING
L2
RD-24
Y
CC
L1
GY-9
LOW
XFMR-C
O
L1
VT-14
LOW
PRESSURE
SWITCH
R
G
ELECTRIC
HEAT
RELAY
T1
CONTACTOR(CC)
L2
T2
VT-14(COMMON)
RD-24(COOL)
RD-11
BU-23(HEAT)
R
13
90
60
30
GND
RD-6
208
HIGH
HIGH
HIGH
BR BROWN
60
OR ORANGE
WH WHITE
30
VT VIOLET
BU BLUE
GN GREEN
GY GRAY
TEST
BK BLACK
RD RED
TEST
HIGH
HIGH
COLOR CODE
YL YELLOW
LOW VOLTAGE
LOW VOLTAGE FIELD
ALTERNATE
CONFIGURATION
DETAIL 1
HI VOLTAGE
HI VOLTAGE FIELD
PHD[24-36]C02**
R
DT
COMMON
1
DEFROST
THERMOSTAT
(DT)
TERMINAL BOARD
DEFROST
BOARD
VT-7
LINE
LOAD
FIELDCONNECTION
208/230VAC1Ø
GY-9
(CAP)
DF1
COM
230/208
HEATER
KIT
DF2
GND
TRANSFORMER
FOR PROPER OPERATION ON 208 VOLT THE
FOLLOWING CHANGE MUST BE MADE:
MOVE RD6 WIRE FROM TRANSFORMER
230 TERMINAL TO 208 TERMINAL.
WARNING
DISCONNECT ELECTRICAL POWER TO THIS UNIT BEFORE SERVICING OR PERFORMING MAINTENANCE. FAILURE TO DISCONNECT
THE ELECTRICAL POWER BEFORE WORKING ON THIS PRODUCT CAN CREATE A HAZARD LEADING TO PROPERTY DAMAGE,
PERSONAL INJURY OR DEATH.
208 VOLT INSTALLATION
AIR
CIRCULATION
BLOWER
(ACB)
Y
BLOWER
INTERFACE
HE AT
A
B
C
D
TO HEATER KIT
A
S
8
7
DFT
9
YL
12
W
4
G
5
Y
6
O
1
C
2
R
DF1
VIEW A-A
90
60
30
DF2
RD
BK
GN
O.D.
FAN
MOTOR
1
ALTERNATE UNIT POWER REFRIGERANT
LEADS MAY BE USED WITH ELECTRIC
HEATER ACCESSORIES. SEE HEATER
ACCESSORY INSTALLATION INSTRUCTIONS.
20473501 REV. 0
BU-34
DETAIL 2
R
HERM
COMP
ADJUST
CFM
CFM (HEAT)
(COOL)
S
T2
T1
2
5
START
RELAY
CAP
NORM
A
800
A
900
A
(+)
B
1000
B
1100
B
(-)
C
1200
C
1200
C
TEST
D
1400
D
1300
D
TEST
C
1
208/230 VAC 1Ø
WARNING:DISCONNECT POWER BEFORE SERVICING.
USE COPPER CONDUCTORS ONLY
90
COLOR CODE
YL YELLOW
BR BROWN
60
OR ORANGE
WH WHITE
30
VT VIOLET
BU BLUE
GN GREEN
GY GRAY
TEST
BK BLACK
RD RED
TEST
ALTERNATE
CONFIGURATION
L2
L1
HERM
RD-27
FAN
COM
FAN
CAPACITOR
DEFROST
BOARD
230/208
CAP
BK-27
COM
COMMON
24V
BR-11
VT
16
90
60
30
C
Y
O
3
CC
OD
C
OR-49
G
CAP
R
VT
62
BR-21
RD-13
W
LPS
COMPRESSOR
1Ø WIRING
RD
10
YL/BK
YL-27
O
RS
VT
20
LOWPRESSURE
SWITCH(LPS)
W1
EM/W2
O
R2
R3
C1
C2
G
Y/Y2
O
TO
HEATER
KIT
BK
19
TEST
C2
G
C1
O
R3
W2
PIN 1
BK
20
R
R
PIN 2
Y
REVERSING
SOLENOID
(RS)
RD
31
RD-10
R
R2
R
PIN 3
R
A
B
C
D
VT-20
W2
W1
DFT
14
PIN 4
C
BK
13
CU T TO
EN ABLE
DE HUM ID IFY
HEAT
A
B
C
D
RD-27
BK
24
O
EM/W2
Y/Y2
(-)
T EST
COOL
YL/BK
DEFROST
THERMOSTAT
(DT)
YL-27
OR-49
BR-21
RD-13
BU-34
GY-70
PIN 5
TERMINAL BOARD
TEST
NORM
( )+
GY
8
DETAIL 1
LOW VOLTAGE
LOW VOLTAGE FIELD
HI VOLTAGE
HI VOLTAGE FIELD
PHD42C02**
ADJUST
A
PIN 6
DT
RD
33
BLOWER
INTERFACE
PIN 7
CC
VT
62
GY-8
PIN 8
START
L2
USE COPPER
CONDUCTORS
ONLY75°C MIN
GY-9
SEE DETAIL 2
FAN
L2
VT-14
DF1
90
60
30
L1
CONTACTOR(CC)
T2
PIN 9
DEFROST
BOARD
L1
T1
GY-9
RD-31
HEATER
KIT
DF2
GND
RD-6
208
O
W2
230
Y
W1
VT-7
LINE
LOAD
FIELDCONNECTION
208/230VAC1Ø
C
G
COOL
E
A
B
C
D
C
AD JUST
NOR M
( )+
(-)
TEST
W
R
COM
CU T TO
EN ABLE
O
DE HUM ID IFY
AIR
CIRCULATION
BLOWER
(ACB)
GND
TRANSFORMER
FOR PROPER OPERATION ON 208 VOLT THE
FOLLOWING CHANGE MUST BE MADE:
MOVE RD6 WIRE FROM TRANSFORMER
230 TERMINAL TO 208 TERMINAL.
VT-14
WARNING
DISCONNECT ELECTRICAL POWER TO THIS UNIT BEFORE SERVICING OR PERFORMING MAINTENANCE. FAILURE TO DISCONNECT
THE ELECTRICAL POWER BEFORE WORKING ON THIS PRODUCT CAN CREATE A HAZARD LEADING TO PROPERTY DAMAGE,
PERSONAL INJURY OR DEATH.
VT-14
208 VOLT INSTALLATION
AIR
CIRCULATION
BLOWER
(ACB)
BLOWER
INTERFACE
HE AT
A
B
C
D
A
B
C
D
COOL
TO HEATER KIT
YL-20
ADJUST
NORM
( )+
(-)
T EST
PIN 2
DFT
DF1
VIEW A-A
OD
TEST
C2
G
ALTERNATE UNIT POWER REFRIGERANT
LEADS MAY BE USED WITH ELECTRIC
HEATER ACCESSORIES. SEE HEATER
ACCESSORY INSTALLATION INSTRUCTIONS.
20484301 REV. 3
BU-34
DETAIL 2
COM
CAP
R
HERM
COMP
ADJUST
CFM
90
CFM (HEAT)
(COOL)
T2
COOL
RELAY
1
T1
CC
2
5
START
RELAY
CAP
L2
NORM
A
1350
A
1450
(+)
B
1550
B
1650
B
(-)
C
1750
C
1850
C
TEST
D
1950
D
2000
D
A
TEST
S
START
90
60
30
C
2ND
STAGE
208/230 VAC 1 Ø
COLOR CODE
YL YELLOW
BR BROWN
60
OR ORANGE
WH WHITE
30
VT VIOLET
BU BLUE
GN GREEN
GY GRAY
TEST
BK BLACK
RD RED
TEST
LOW VOLTAGE
LOW VOLTAGE FIELD
ALTERNATE
CONFIGURATION
L1
WARNING:DISCONNECT POWER BEFORE SERVICING.
USE COPPER CONDUCTORS ONLY
HERM
RD-27
FAN
FAN
FAN
CAPACITOR
DEFROST
BOARD
230/208
CAP
O.D.
FAN
MOTOR
1
RD
BK
GN
2ND STAGE
DEFROST RELAY
BK-27
COM
DF2
CS
BR-11
VT
16
90
60
30
TEST
1
7
CC
24V
2
8
YL
12
BU-34
Y1
9
W
4
2ND
STAGE
DEFR
RELAY
C
OR-49
G
5
Y2
6
O
1
C
2
R
C
Y1
LPS
3
Y
G
DT
3
YL-27
OR-49
Y1
W
2ND STAGE
COOL RELAY
S
RD-13
O
RS
YL-47
R
VT
62
4
O
Y2
COOL
RELAY
YL-29
YL-29
BR-21
5
O
90
60
30
YL
27
COMPRESSOR
1Ø WIRING
RD
10
2ND
STAGE
GY-10
A
TO
HEATER
KIT
VT
20
YL-10
R
W2
PIN 1
R
YL-29
R
C1
C
BK
19
W2
O
PIN 3
W1
EM/W2
O
R2
R3
C1
C2
G
Y/Y2
PIN 4
TERMINAL BOARD
R
DEFROST
BOARD
RD
31
BR-21
BK
20
O
R3
R
15
PIN 5
DT
REVERSING
SOLENOID
(RS)
YL-37
YL-29
OR-49
BR-21
RD-13
BU-34
GY-70
PIN 6
VT-20
RD-10
O
R2
DFT
PIN 7
A
B
C
D
A
B
C
D
RD-27
DEFR
RELAY
Y
W1
PIN 8
BK
13
CU T TO
EN ABLE
DE HUM ID IFY
HEAT
COOL
YL-10
2ND
STAGE
BK
24
VT
62
DETAIL 1
HI VOLTAGE
HI VOLTAGE FIELD
PHD60C02**
BLOWER
INTERFACE
BU
DEFROST
THERMOSTAT
(DT)
USE COPPER
CONDUCTORS
ONLY75°C MIN
YL/BK
C
EM/W2
Y/Y2
A
Y1
COMPR SOLENOID (CS)
GY
RD 8
33
SEE DETAIL 2
PIN 9
DF1
BK40
BU
HEATER
KIT
DF2
L2
LOWPRESSURE
SWITCH(LPS)
T'STAT
BK40
1
W2
INDUCTOR (OPTIONAL)
L1
CONTACTOR(CC)
L2
T2
DISCH
GY-9
2
W1
GY-9
RD-31
L1
3
G
T1
4
E
GND
RD-6
208
5
C
AD JUST
NOR M
( )+
(-)
TEST
W
R
230
FIELDCONNECTION
208/230VAC1Ø
VT-7
LINE
LOAD
CU T TO
EN ABLE
INDUCTOR (OPTIONAL)
Y
O
COM
VT-14
RD-31
DE HUM ID IFY
AIR
CIRCULATION
BLOWER
(ACB)
GND
TRANSFORMER
FOR PROPER OPERATION ON 208 VOLT
THE FOLLOWING CHANGE MUST BE MADE:
MOVE RD6 WIRE FROM TRANSFORMER
230 TERMINAL TO 208 TERMINAL.
WARNING
DISCONNECT ELECTRICAL POWER TO THIS UNIT BEFORE SERVICING OR PERFORMING MAINTENANCE. FAILURE TO DISCONNECT
THE ELECTRICAL POWER BEFORE WORKING ON THIS PRODUCT CAN CREATE A HAZARD LEADING TO PROPERTY DAMAGE,
PERSONAL INJURY OR DEATH.
208 VOLT INSTALLATION
CAPACITOR
(CAP)
GND
TRANSFORMER
FOR PROPER OPERATION ON 208 VOLT THE
FOLLOWING CHANGE MUST BE MADE:
MOVE RD6 WIRE FROM TRANSFORMER
230 TERMINAL TO 208 TERMINAL.
COM
VT-7
LINE
LOAD
230
RD-6
208
BR
BR
AIR
CIRCULATION
BLOWER
(ACB)
6
1
4
5
2
HI
3
MED HI
CONTACTOR(CC)
T2
L2
VT-14(COMMON)
RD-24(COOL)
RD-11
BU-23(HEAT)
MED LOW
L1
T1
GY-9
COMMON
VT-14
BU-23
GY-8
RD-33
XFMR-R
VT-20
R
WH-7
RD-10
G
C
VT-62
OR-28
BK-26
VT
20
BU
23
VT-18
BU-1
COMPRESSOR
1 Ø WIRING
RD
10
BK-19
BK-20
A
O
W2
R
R
DFT
2
1
6
5
4
9
8
7
DEFROST
BOARD
TEST
90
60
30
1
3
S
ELECTRIC
HEAT
RELAY
C
YL
12
BR-11
GY-55
O
A
DF2
TO
HEATER
KIT
2
RD-31
DF1
PIN 1
W
PIN 2
G
PIN 3
C
PIN 4
Y
PIN 5
O
PIN 6
R
RD
31
1
5
4
Y
PIN 7
RD-22
BR-21
RD-13
OR-49
R
BK-26
VT-18
YL-27
OR-49
BR-21
RD-13
BU-34
GY-70
PIN 8
3
YL-27
PIN 9
C
VT
16
COM
O.D.
FAN
MOTOR
GND
T2
BK-27
FAN
T1
HERM
CAPACITOR
RD-27
22304101 REV. 0
BU-34
90
TEST
VIEW A-A
90
60
30
16
COOLING
SWITCH
RELAY
BK-13
REVERSING
SOLENOID
(RS)
RD-27
NO NC
XFMR-C
BK-24
RD
31
BU-1
COM
PHB[24-36]CC2**
VT
62
RD-24
DEFROST
THERMOSTAT
(DT)
USE COPPER
CONDUCTORS
ONLY75 °C MIN
GY-9
LOW
COLOR CODE
YL YELLOW
BR BROWN
60
OR ORANGE
WH WHITE
30
VT VIOLET
BU BLUE
GN GREEN
GY GRAY
TEST
BK BLACK
RD RED
TEST
LOW VOLTAGE
LOW VOLTAGE FIELD
ALTERNATE
CONFIGURATION
DETAIL 1
HI VOLTAGE
HI VOLTAGE FIELD
WARNING
DISCONNECT ELECTRICAL POWER TO THIS UNIT BEFORE SERVICING OR PERFORMING MAINTENANCE. FAILURE TO DISCONNECT
THE ELECTRICAL POWER BEFORE WORKING ON THIS PRODUCT CAN CREATE A HAZARD LEADING TO PROPERTY DAMAGE,
PERSONAL INJURY OR DEATH.
208 VOLT INSTALLATION
GND
TRANSFORMER
FOR PROPER OPERATION ON 208 VOLT THE
FOLLOWING CHANGE MUST BE MADE:
MOVE RD6 WIRE FROM TRANSFORMER
230 TERMINAL TO 208 TERMINAL.
COM
VT-7
LINE
LOAD
230
RD-6
208
L1
T1
CAPACITOR
(CAP)
GY-9
BR
BR
AIR
CIRCULATION
BLOWER
(ACB)
6
COMMON
1
2
HI
3
MED HI
4
5
CONTACTOR(CC)
L2
T2
VT-14(COMMON)
RD-24(COOL)
RD-11
BU-23(HEAT)
MED LOW
VT-14
VT
62
RD-24
LOW
PRESSURE
SWITCH
GY-8
RD-33
VT-20
R
YL\BK
RD-10
G
C
17
VT-62
COOLING
SWITCH
RELAY
BK-13
OR-28
REVERSING
SOLENOID
(RS)
RD-27
NO NC
XFMR-C
BK-24
RD
31
YL\BK
COM
XFMR-R
WH-7
BK-26
VT
20
BU
23
VT-18
COMPRESSOR
1 Ø WIRING
RD
10
BK-19
BK-20
A
Y
O
O
R
R
DFT
2
1
6
5
4
9
8
7
DEFROST
BOARD
TEST
90
60
30
1
3
ELECTRIC
HEAT
RELAY
C
YL
12
BR-11
GY-55
W2
DF2
A
S
RD-31
DF1
TO
HEATER
KIT
W
PIN 1
G
PIN 2
Y
PIN 3
C
PIN 4
O
PIN 5
R
PIN 6
2
4
R
RD
31
1
5
C
PIN 7
RD-22
BR-21
RD-13
OR-49
BK-26
VT-18
YL-27
OR-49
BR-21
RD-13
BU-34
GY-70
PIN 8
3
YL-27
PIN 9
PHD[24-36]CC2**
BU-23
DEFROST
THERMOSTAT
(DT)
USE COPPER
CONDUCTORS
ONLY75°C MIN
GY-9
LOW
VT
16
COM
O.D.
FAN
MOTOR
GND
T2
BK-27
FAN
T1
HERM
CAPACITOR
RD-27
22304201 REV. 0
VIEW A-A
BU-34
TEST
ALTERNATE UNIT POWER REFRIGERANT
LEADS MAY BE USED WITH ELECTRIC
HEATER ACCESSORIES. SEE HEATER
ACCESSORY INSTALLATION INSTRUCTIONS.
90
60
30
RD
BK
GN
90
COLOR CODE
YL YELLOW
BR BROWN
60
OR ORANGE
WH WHITE
30
VT VIOLET
BU BLUE
GN GREEN
GY GRAY
TEST
BK BLACK
RD RED
TEST
LOW VOLTAGE
LOW VOLTAGE FIELD
ALTERNATE
CONFIGURATION
DETAIL 1
HI VOLTAGE
HI VOLTAGE FIELD
CLEARANCES
WARNING
TO
AVOID PROPERTY DAMAGE, PERSONAL INJURY OR DEATH
DUE TO FIRE, CLEARANCES TO COMBUSTIBLE SURFACES LISTED
AS SHOWN MUST BE OBSERVED.
36" Side
Clearance
for Servicing
Recommended
24" Clearance
(Condenser End)
36"
Maximum
Overhang
48" Minimum
Overhang
Vinyl Coated
Canvas
Connections
Insulate
Return
Duct
Minimum 9" Clearance
to Combustibles
36" Clearance for
Service Required
18
0" Minimum
Clearance to
Combustibles
Insulated
Supply
Duct
19
20
©2000-2004 Goodman Company, L.P.
Effective: September 2004